| // SPDX-License-Identifier: GPL-2.0 |
| // |
| // Freescale ESAI ALSA SoC Digital Audio Interface (DAI) driver |
| // |
| // Copyright (C) 2014 Freescale Semiconductor, Inc. |
| |
| #include <linux/clk.h> |
| #include <linux/dmaengine.h> |
| #include <linux/module.h> |
| #include <linux/of_irq.h> |
| #include <linux/of_platform.h> |
| #include <sound/dmaengine_pcm.h> |
| #include <sound/pcm_params.h> |
| |
| #include "fsl_esai.h" |
| #include "imx-pcm.h" |
| |
| #define FSL_ESAI_FORMATS (SNDRV_PCM_FMTBIT_S8 | \ |
| SNDRV_PCM_FMTBIT_S16_LE | \ |
| SNDRV_PCM_FMTBIT_S20_3LE | \ |
| SNDRV_PCM_FMTBIT_S24_LE) |
| |
| /** |
| * fsl_esai: ESAI private data |
| * |
| * @dma_params_rx: DMA parameters for receive channel |
| * @dma_params_tx: DMA parameters for transmit channel |
| * @pdev: platform device pointer |
| * @regmap: regmap handler |
| * @coreclk: clock source to access register |
| * @extalclk: esai clock source to derive HCK, SCK and FS |
| * @fsysclk: system clock source to derive HCK, SCK and FS |
| * @spbaclk: SPBA clock (optional, depending on SoC design) |
| * @fifo_depth: depth of tx/rx FIFO |
| * @slot_width: width of each DAI slot |
| * @slots: number of slots |
| * @hck_rate: clock rate of desired HCKx clock |
| * @sck_rate: clock rate of desired SCKx clock |
| * @hck_dir: the direction of HCKx pads |
| * @sck_div: if using PSR/PM dividers for SCKx clock |
| * @slave_mode: if fully using DAI slave mode |
| * @synchronous: if using tx/rx synchronous mode |
| * @name: driver name |
| */ |
| struct fsl_esai { |
| struct snd_dmaengine_dai_dma_data dma_params_rx; |
| struct snd_dmaengine_dai_dma_data dma_params_tx; |
| struct platform_device *pdev; |
| struct regmap *regmap; |
| struct clk *coreclk; |
| struct clk *extalclk; |
| struct clk *fsysclk; |
| struct clk *spbaclk; |
| u32 fifo_depth; |
| u32 slot_width; |
| u32 slots; |
| u32 tx_mask; |
| u32 rx_mask; |
| u32 hck_rate[2]; |
| u32 sck_rate[2]; |
| bool hck_dir[2]; |
| bool sck_div[2]; |
| bool slave_mode; |
| bool synchronous; |
| char name[32]; |
| }; |
| |
| static irqreturn_t esai_isr(int irq, void *devid) |
| { |
| struct fsl_esai *esai_priv = (struct fsl_esai *)devid; |
| struct platform_device *pdev = esai_priv->pdev; |
| u32 esr; |
| |
| regmap_read(esai_priv->regmap, REG_ESAI_ESR, &esr); |
| |
| if (esr & ESAI_ESR_TINIT_MASK) |
| dev_dbg(&pdev->dev, "isr: Transmission Initialized\n"); |
| |
| if (esr & ESAI_ESR_RFF_MASK) |
| dev_warn(&pdev->dev, "isr: Receiving overrun\n"); |
| |
| if (esr & ESAI_ESR_TFE_MASK) |
| dev_warn(&pdev->dev, "isr: Transmission underrun\n"); |
| |
| if (esr & ESAI_ESR_TLS_MASK) |
| dev_dbg(&pdev->dev, "isr: Just transmitted the last slot\n"); |
| |
| if (esr & ESAI_ESR_TDE_MASK) |
| dev_dbg(&pdev->dev, "isr: Transmission data exception\n"); |
| |
| if (esr & ESAI_ESR_TED_MASK) |
| dev_dbg(&pdev->dev, "isr: Transmitting even slots\n"); |
| |
| if (esr & ESAI_ESR_TD_MASK) |
| dev_dbg(&pdev->dev, "isr: Transmitting data\n"); |
| |
| if (esr & ESAI_ESR_RLS_MASK) |
| dev_dbg(&pdev->dev, "isr: Just received the last slot\n"); |
| |
| if (esr & ESAI_ESR_RDE_MASK) |
| dev_dbg(&pdev->dev, "isr: Receiving data exception\n"); |
| |
| if (esr & ESAI_ESR_RED_MASK) |
| dev_dbg(&pdev->dev, "isr: Receiving even slots\n"); |
| |
| if (esr & ESAI_ESR_RD_MASK) |
| dev_dbg(&pdev->dev, "isr: Receiving data\n"); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /** |
| * This function is used to calculate the divisors of psr, pm, fp and it is |
| * supposed to be called in set_dai_sysclk() and set_bclk(). |
| * |
| * @ratio: desired overall ratio for the paticipating dividers |
| * @usefp: for HCK setting, there is no need to set fp divider |
| * @fp: bypass other dividers by setting fp directly if fp != 0 |
| * @tx: current setting is for playback or capture |
| */ |
| static int fsl_esai_divisor_cal(struct snd_soc_dai *dai, bool tx, u32 ratio, |
| bool usefp, u32 fp) |
| { |
| struct fsl_esai *esai_priv = snd_soc_dai_get_drvdata(dai); |
| u32 psr, pm = 999, maxfp, prod, sub, savesub, i, j; |
| |
| maxfp = usefp ? 16 : 1; |
| |
| if (usefp && fp) |
| goto out_fp; |
| |
| if (ratio > 2 * 8 * 256 * maxfp || ratio < 2) { |
| dev_err(dai->dev, "the ratio is out of range (2 ~ %d)\n", |
| 2 * 8 * 256 * maxfp); |
| return -EINVAL; |
| } else if (ratio % 2) { |
| dev_err(dai->dev, "the raio must be even if using upper divider\n"); |
| return -EINVAL; |
| } |
| |
| ratio /= 2; |
| |
| psr = ratio <= 256 * maxfp ? ESAI_xCCR_xPSR_BYPASS : ESAI_xCCR_xPSR_DIV8; |
| |
| /* Do not loop-search if PM (1 ~ 256) alone can serve the ratio */ |
| if (ratio <= 256) { |
| pm = ratio; |
| fp = 1; |
| goto out; |
| } |
| |
| /* Set the max fluctuation -- 0.1% of the max devisor */ |
| savesub = (psr ? 1 : 8) * 256 * maxfp / 1000; |
| |
| /* Find the best value for PM */ |
| for (i = 1; i <= 256; i++) { |
| for (j = 1; j <= maxfp; j++) { |
| /* PSR (1 or 8) * PM (1 ~ 256) * FP (1 ~ 16) */ |
| prod = (psr ? 1 : 8) * i * j; |
| |
| if (prod == ratio) |
| sub = 0; |
| else if (prod / ratio == 1) |
| sub = prod - ratio; |
| else if (ratio / prod == 1) |
| sub = ratio - prod; |
| else |
| continue; |
| |
| /* Calculate the fraction */ |
| sub = sub * 1000 / ratio; |
| if (sub < savesub) { |
| savesub = sub; |
| pm = i; |
| fp = j; |
| } |
| |
| /* We are lucky */ |
| if (savesub == 0) |
| goto out; |
| } |
| } |
| |
| if (pm == 999) { |
| dev_err(dai->dev, "failed to calculate proper divisors\n"); |
| return -EINVAL; |
| } |
| |
| out: |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xCCR(tx), |
| ESAI_xCCR_xPSR_MASK | ESAI_xCCR_xPM_MASK, |
| psr | ESAI_xCCR_xPM(pm)); |
| |
| out_fp: |
| /* Bypass fp if not being required */ |
| if (maxfp <= 1) |
| return 0; |
| |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xCCR(tx), |
| ESAI_xCCR_xFP_MASK, ESAI_xCCR_xFP(fp)); |
| |
| return 0; |
| } |
| |
| /** |
| * This function mainly configures the clock frequency of MCLK (HCKT/HCKR) |
| * |
| * @Parameters: |
| * clk_id: The clock source of HCKT/HCKR |
| * (Input from outside; output from inside, FSYS or EXTAL) |
| * freq: The required clock rate of HCKT/HCKR |
| * dir: The clock direction of HCKT/HCKR |
| * |
| * Note: If the direction is input, we do not care about clk_id. |
| */ |
| static int fsl_esai_set_dai_sysclk(struct snd_soc_dai *dai, int clk_id, |
| unsigned int freq, int dir) |
| { |
| struct fsl_esai *esai_priv = snd_soc_dai_get_drvdata(dai); |
| struct clk *clksrc = esai_priv->extalclk; |
| bool tx = clk_id <= ESAI_HCKT_EXTAL; |
| bool in = dir == SND_SOC_CLOCK_IN; |
| u32 ratio, ecr = 0; |
| unsigned long clk_rate; |
| int ret; |
| |
| if (freq == 0) { |
| dev_err(dai->dev, "%sput freq of HCK%c should not be 0Hz\n", |
| in ? "in" : "out", tx ? 'T' : 'R'); |
| return -EINVAL; |
| } |
| |
| /* Bypass divider settings if the requirement doesn't change */ |
| if (freq == esai_priv->hck_rate[tx] && dir == esai_priv->hck_dir[tx]) |
| return 0; |
| |
| /* sck_div can be only bypassed if ETO/ERO=0 and SNC_SOC_CLOCK_OUT */ |
| esai_priv->sck_div[tx] = true; |
| |
| /* Set the direction of HCKT/HCKR pins */ |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xCCR(tx), |
| ESAI_xCCR_xHCKD, in ? 0 : ESAI_xCCR_xHCKD); |
| |
| if (in) |
| goto out; |
| |
| switch (clk_id) { |
| case ESAI_HCKT_FSYS: |
| case ESAI_HCKR_FSYS: |
| clksrc = esai_priv->fsysclk; |
| break; |
| case ESAI_HCKT_EXTAL: |
| ecr |= ESAI_ECR_ETI; |
| break; |
| case ESAI_HCKR_EXTAL: |
| ecr |= ESAI_ECR_ERI; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| if (IS_ERR(clksrc)) { |
| dev_err(dai->dev, "no assigned %s clock\n", |
| clk_id % 2 ? "extal" : "fsys"); |
| return PTR_ERR(clksrc); |
| } |
| clk_rate = clk_get_rate(clksrc); |
| |
| ratio = clk_rate / freq; |
| if (ratio * freq > clk_rate) |
| ret = ratio * freq - clk_rate; |
| else if (ratio * freq < clk_rate) |
| ret = clk_rate - ratio * freq; |
| else |
| ret = 0; |
| |
| /* Block if clock source can not be divided into the required rate */ |
| if (ret != 0 && clk_rate / ret < 1000) { |
| dev_err(dai->dev, "failed to derive required HCK%c rate\n", |
| tx ? 'T' : 'R'); |
| return -EINVAL; |
| } |
| |
| /* Only EXTAL source can be output directly without using PSR and PM */ |
| if (ratio == 1 && clksrc == esai_priv->extalclk) { |
| /* Bypass all the dividers if not being needed */ |
| ecr |= tx ? ESAI_ECR_ETO : ESAI_ECR_ERO; |
| goto out; |
| } else if (ratio < 2) { |
| /* The ratio should be no less than 2 if using other sources */ |
| dev_err(dai->dev, "failed to derive required HCK%c rate\n", |
| tx ? 'T' : 'R'); |
| return -EINVAL; |
| } |
| |
| ret = fsl_esai_divisor_cal(dai, tx, ratio, false, 0); |
| if (ret) |
| return ret; |
| |
| esai_priv->sck_div[tx] = false; |
| |
| out: |
| esai_priv->hck_dir[tx] = dir; |
| esai_priv->hck_rate[tx] = freq; |
| |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_ECR, |
| tx ? ESAI_ECR_ETI | ESAI_ECR_ETO : |
| ESAI_ECR_ERI | ESAI_ECR_ERO, ecr); |
| |
| return 0; |
| } |
| |
| /** |
| * This function configures the related dividers according to the bclk rate |
| */ |
| static int fsl_esai_set_bclk(struct snd_soc_dai *dai, bool tx, u32 freq) |
| { |
| struct fsl_esai *esai_priv = snd_soc_dai_get_drvdata(dai); |
| u32 hck_rate = esai_priv->hck_rate[tx]; |
| u32 sub, ratio = hck_rate / freq; |
| int ret; |
| |
| /* Don't apply for fully slave mode or unchanged bclk */ |
| if (esai_priv->slave_mode || esai_priv->sck_rate[tx] == freq) |
| return 0; |
| |
| if (ratio * freq > hck_rate) |
| sub = ratio * freq - hck_rate; |
| else if (ratio * freq < hck_rate) |
| sub = hck_rate - ratio * freq; |
| else |
| sub = 0; |
| |
| /* Block if clock source can not be divided into the required rate */ |
| if (sub != 0 && hck_rate / sub < 1000) { |
| dev_err(dai->dev, "failed to derive required SCK%c rate\n", |
| tx ? 'T' : 'R'); |
| return -EINVAL; |
| } |
| |
| /* The ratio should be contented by FP alone if bypassing PM and PSR */ |
| if (!esai_priv->sck_div[tx] && (ratio > 16 || ratio == 0)) { |
| dev_err(dai->dev, "the ratio is out of range (1 ~ 16)\n"); |
| return -EINVAL; |
| } |
| |
| ret = fsl_esai_divisor_cal(dai, tx, ratio, true, |
| esai_priv->sck_div[tx] ? 0 : ratio); |
| if (ret) |
| return ret; |
| |
| /* Save current bclk rate */ |
| esai_priv->sck_rate[tx] = freq; |
| |
| return 0; |
| } |
| |
| static int fsl_esai_set_dai_tdm_slot(struct snd_soc_dai *dai, u32 tx_mask, |
| u32 rx_mask, int slots, int slot_width) |
| { |
| struct fsl_esai *esai_priv = snd_soc_dai_get_drvdata(dai); |
| |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_TCCR, |
| ESAI_xCCR_xDC_MASK, ESAI_xCCR_xDC(slots)); |
| |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_RCCR, |
| ESAI_xCCR_xDC_MASK, ESAI_xCCR_xDC(slots)); |
| |
| esai_priv->slot_width = slot_width; |
| esai_priv->slots = slots; |
| esai_priv->tx_mask = tx_mask; |
| esai_priv->rx_mask = rx_mask; |
| |
| return 0; |
| } |
| |
| static int fsl_esai_set_dai_fmt(struct snd_soc_dai *dai, unsigned int fmt) |
| { |
| struct fsl_esai *esai_priv = snd_soc_dai_get_drvdata(dai); |
| u32 xcr = 0, xccr = 0, mask; |
| |
| /* DAI mode */ |
| switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { |
| case SND_SOC_DAIFMT_I2S: |
| /* Data on rising edge of bclk, frame low, 1clk before data */ |
| xcr |= ESAI_xCR_xFSR; |
| xccr |= ESAI_xCCR_xFSP | ESAI_xCCR_xCKP | ESAI_xCCR_xHCKP; |
| break; |
| case SND_SOC_DAIFMT_LEFT_J: |
| /* Data on rising edge of bclk, frame high */ |
| xccr |= ESAI_xCCR_xCKP | ESAI_xCCR_xHCKP; |
| break; |
| case SND_SOC_DAIFMT_RIGHT_J: |
| /* Data on rising edge of bclk, frame high, right aligned */ |
| xccr |= ESAI_xCCR_xCKP | ESAI_xCCR_xHCKP; |
| xcr |= ESAI_xCR_xWA; |
| break; |
| case SND_SOC_DAIFMT_DSP_A: |
| /* Data on rising edge of bclk, frame high, 1clk before data */ |
| xcr |= ESAI_xCR_xFSL | ESAI_xCR_xFSR; |
| xccr |= ESAI_xCCR_xCKP | ESAI_xCCR_xHCKP; |
| break; |
| case SND_SOC_DAIFMT_DSP_B: |
| /* Data on rising edge of bclk, frame high */ |
| xcr |= ESAI_xCR_xFSL; |
| xccr |= ESAI_xCCR_xCKP | ESAI_xCCR_xHCKP; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| /* DAI clock inversion */ |
| switch (fmt & SND_SOC_DAIFMT_INV_MASK) { |
| case SND_SOC_DAIFMT_NB_NF: |
| /* Nothing to do for both normal cases */ |
| break; |
| case SND_SOC_DAIFMT_IB_NF: |
| /* Invert bit clock */ |
| xccr ^= ESAI_xCCR_xCKP | ESAI_xCCR_xHCKP; |
| break; |
| case SND_SOC_DAIFMT_NB_IF: |
| /* Invert frame clock */ |
| xccr ^= ESAI_xCCR_xFSP; |
| break; |
| case SND_SOC_DAIFMT_IB_IF: |
| /* Invert both clocks */ |
| xccr ^= ESAI_xCCR_xCKP | ESAI_xCCR_xHCKP | ESAI_xCCR_xFSP; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| esai_priv->slave_mode = false; |
| |
| /* DAI clock master masks */ |
| switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { |
| case SND_SOC_DAIFMT_CBM_CFM: |
| esai_priv->slave_mode = true; |
| break; |
| case SND_SOC_DAIFMT_CBS_CFM: |
| xccr |= ESAI_xCCR_xCKD; |
| break; |
| case SND_SOC_DAIFMT_CBM_CFS: |
| xccr |= ESAI_xCCR_xFSD; |
| break; |
| case SND_SOC_DAIFMT_CBS_CFS: |
| xccr |= ESAI_xCCR_xFSD | ESAI_xCCR_xCKD; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| mask = ESAI_xCR_xFSL | ESAI_xCR_xFSR | ESAI_xCR_xWA; |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_TCR, mask, xcr); |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_RCR, mask, xcr); |
| |
| mask = ESAI_xCCR_xCKP | ESAI_xCCR_xHCKP | ESAI_xCCR_xFSP | |
| ESAI_xCCR_xFSD | ESAI_xCCR_xCKD; |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_TCCR, mask, xccr); |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_RCCR, mask, xccr); |
| |
| return 0; |
| } |
| |
| static int fsl_esai_startup(struct snd_pcm_substream *substream, |
| struct snd_soc_dai *dai) |
| { |
| struct fsl_esai *esai_priv = snd_soc_dai_get_drvdata(dai); |
| int ret; |
| |
| /* |
| * Some platforms might use the same bit to gate all three or two of |
| * clocks, so keep all clocks open/close at the same time for safety |
| */ |
| ret = clk_prepare_enable(esai_priv->coreclk); |
| if (ret) |
| return ret; |
| if (!IS_ERR(esai_priv->spbaclk)) { |
| ret = clk_prepare_enable(esai_priv->spbaclk); |
| if (ret) |
| goto err_spbaclk; |
| } |
| if (!IS_ERR(esai_priv->extalclk)) { |
| ret = clk_prepare_enable(esai_priv->extalclk); |
| if (ret) |
| goto err_extalck; |
| } |
| if (!IS_ERR(esai_priv->fsysclk)) { |
| ret = clk_prepare_enable(esai_priv->fsysclk); |
| if (ret) |
| goto err_fsysclk; |
| } |
| |
| if (!dai->active) { |
| /* Set synchronous mode */ |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_SAICR, |
| ESAI_SAICR_SYNC, esai_priv->synchronous ? |
| ESAI_SAICR_SYNC : 0); |
| |
| /* Set a default slot number -- 2 */ |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_TCCR, |
| ESAI_xCCR_xDC_MASK, ESAI_xCCR_xDC(2)); |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_RCCR, |
| ESAI_xCCR_xDC_MASK, ESAI_xCCR_xDC(2)); |
| } |
| |
| return 0; |
| |
| err_fsysclk: |
| if (!IS_ERR(esai_priv->extalclk)) |
| clk_disable_unprepare(esai_priv->extalclk); |
| err_extalck: |
| if (!IS_ERR(esai_priv->spbaclk)) |
| clk_disable_unprepare(esai_priv->spbaclk); |
| err_spbaclk: |
| clk_disable_unprepare(esai_priv->coreclk); |
| |
| return ret; |
| } |
| |
| static int fsl_esai_hw_params(struct snd_pcm_substream *substream, |
| struct snd_pcm_hw_params *params, |
| struct snd_soc_dai *dai) |
| { |
| struct fsl_esai *esai_priv = snd_soc_dai_get_drvdata(dai); |
| bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; |
| u32 width = params_width(params); |
| u32 channels = params_channels(params); |
| u32 pins = DIV_ROUND_UP(channels, esai_priv->slots); |
| u32 slot_width = width; |
| u32 bclk, mask, val; |
| int ret; |
| |
| /* Override slot_width if being specifically set */ |
| if (esai_priv->slot_width) |
| slot_width = esai_priv->slot_width; |
| |
| bclk = params_rate(params) * slot_width * esai_priv->slots; |
| |
| ret = fsl_esai_set_bclk(dai, tx, bclk); |
| if (ret) |
| return ret; |
| |
| /* Use Normal mode to support monaural audio */ |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xCR(tx), |
| ESAI_xCR_xMOD_MASK, params_channels(params) > 1 ? |
| ESAI_xCR_xMOD_NETWORK : 0); |
| |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xFCR(tx), |
| ESAI_xFCR_xFR_MASK, ESAI_xFCR_xFR); |
| |
| mask = ESAI_xFCR_xFR_MASK | ESAI_xFCR_xWA_MASK | ESAI_xFCR_xFWM_MASK | |
| (tx ? ESAI_xFCR_TE_MASK | ESAI_xFCR_TIEN : ESAI_xFCR_RE_MASK); |
| val = ESAI_xFCR_xWA(width) | ESAI_xFCR_xFWM(esai_priv->fifo_depth) | |
| (tx ? ESAI_xFCR_TE(pins) | ESAI_xFCR_TIEN : ESAI_xFCR_RE(pins)); |
| |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xFCR(tx), mask, val); |
| |
| mask = ESAI_xCR_xSWS_MASK | (tx ? ESAI_xCR_PADC : 0); |
| val = ESAI_xCR_xSWS(slot_width, width) | (tx ? ESAI_xCR_PADC : 0); |
| |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xCR(tx), mask, val); |
| |
| /* Remove ESAI personal reset by configuring ESAI_PCRC and ESAI_PRRC */ |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_PRRC, |
| ESAI_PRRC_PDC_MASK, ESAI_PRRC_PDC(ESAI_GPIO)); |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_PCRC, |
| ESAI_PCRC_PC_MASK, ESAI_PCRC_PC(ESAI_GPIO)); |
| return 0; |
| } |
| |
| static void fsl_esai_shutdown(struct snd_pcm_substream *substream, |
| struct snd_soc_dai *dai) |
| { |
| struct fsl_esai *esai_priv = snd_soc_dai_get_drvdata(dai); |
| |
| if (!IS_ERR(esai_priv->fsysclk)) |
| clk_disable_unprepare(esai_priv->fsysclk); |
| if (!IS_ERR(esai_priv->extalclk)) |
| clk_disable_unprepare(esai_priv->extalclk); |
| if (!IS_ERR(esai_priv->spbaclk)) |
| clk_disable_unprepare(esai_priv->spbaclk); |
| clk_disable_unprepare(esai_priv->coreclk); |
| } |
| |
| static int fsl_esai_trigger(struct snd_pcm_substream *substream, int cmd, |
| struct snd_soc_dai *dai) |
| { |
| struct fsl_esai *esai_priv = snd_soc_dai_get_drvdata(dai); |
| bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; |
| u8 i, channels = substream->runtime->channels; |
| u32 pins = DIV_ROUND_UP(channels, esai_priv->slots); |
| u32 mask; |
| |
| switch (cmd) { |
| case SNDRV_PCM_TRIGGER_START: |
| case SNDRV_PCM_TRIGGER_RESUME: |
| case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xFCR(tx), |
| ESAI_xFCR_xFEN_MASK, ESAI_xFCR_xFEN); |
| |
| /* Write initial words reqiured by ESAI as normal procedure */ |
| for (i = 0; tx && i < channels; i++) |
| regmap_write(esai_priv->regmap, REG_ESAI_ETDR, 0x0); |
| |
| /* |
| * When set the TE/RE in the end of enablement flow, there |
| * will be channel swap issue for multi data line case. |
| * In order to workaround this issue, we switch the bit |
| * enablement sequence to below sequence |
| * 1) clear the xSMB & xSMA: which is done in probe and |
| * stop state. |
| * 2) set TE/RE |
| * 3) set xSMB |
| * 4) set xSMA: xSMA is the last one in this flow, which |
| * will trigger esai to start. |
| */ |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xCR(tx), |
| tx ? ESAI_xCR_TE_MASK : ESAI_xCR_RE_MASK, |
| tx ? ESAI_xCR_TE(pins) : ESAI_xCR_RE(pins)); |
| mask = tx ? esai_priv->tx_mask : esai_priv->rx_mask; |
| |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xSMB(tx), |
| ESAI_xSMB_xS_MASK, ESAI_xSMB_xS(mask)); |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xSMA(tx), |
| ESAI_xSMA_xS_MASK, ESAI_xSMA_xS(mask)); |
| |
| break; |
| case SNDRV_PCM_TRIGGER_SUSPEND: |
| case SNDRV_PCM_TRIGGER_STOP: |
| case SNDRV_PCM_TRIGGER_PAUSE_PUSH: |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xCR(tx), |
| tx ? ESAI_xCR_TE_MASK : ESAI_xCR_RE_MASK, 0); |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xSMA(tx), |
| ESAI_xSMA_xS_MASK, 0); |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xSMB(tx), |
| ESAI_xSMB_xS_MASK, 0); |
| |
| /* Disable and reset FIFO */ |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xFCR(tx), |
| ESAI_xFCR_xFR | ESAI_xFCR_xFEN, ESAI_xFCR_xFR); |
| regmap_update_bits(esai_priv->regmap, REG_ESAI_xFCR(tx), |
| ESAI_xFCR_xFR, 0); |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static const struct snd_soc_dai_ops fsl_esai_dai_ops = { |
| .startup = fsl_esai_startup, |
| .shutdown = fsl_esai_shutdown, |
| .trigger = fsl_esai_trigger, |
| .hw_params = fsl_esai_hw_params, |
| .set_sysclk = fsl_esai_set_dai_sysclk, |
| .set_fmt = fsl_esai_set_dai_fmt, |
| .set_tdm_slot = fsl_esai_set_dai_tdm_slot, |
| }; |
| |
| static int fsl_esai_dai_probe(struct snd_soc_dai *dai) |
| { |
| struct fsl_esai *esai_priv = snd_soc_dai_get_drvdata(dai); |
| |
| snd_soc_dai_init_dma_data(dai, &esai_priv->dma_params_tx, |
| &esai_priv->dma_params_rx); |
| |
| return 0; |
| } |
| |
| static struct snd_soc_dai_driver fsl_esai_dai = { |
| .probe = fsl_esai_dai_probe, |
| .playback = { |
| .stream_name = "CPU-Playback", |
| .channels_min = 1, |
| .channels_max = 12, |
| .rates = SNDRV_PCM_RATE_8000_192000, |
| .formats = FSL_ESAI_FORMATS, |
| }, |
| .capture = { |
| .stream_name = "CPU-Capture", |
| .channels_min = 1, |
| .channels_max = 8, |
| .rates = SNDRV_PCM_RATE_8000_192000, |
| .formats = FSL_ESAI_FORMATS, |
| }, |
| .ops = &fsl_esai_dai_ops, |
| }; |
| |
| static const struct snd_soc_component_driver fsl_esai_component = { |
| .name = "fsl-esai", |
| }; |
| |
| static const struct reg_default fsl_esai_reg_defaults[] = { |
| {REG_ESAI_ETDR, 0x00000000}, |
| {REG_ESAI_ECR, 0x00000000}, |
| {REG_ESAI_TFCR, 0x00000000}, |
| {REG_ESAI_RFCR, 0x00000000}, |
| {REG_ESAI_TX0, 0x00000000}, |
| {REG_ESAI_TX1, 0x00000000}, |
| {REG_ESAI_TX2, 0x00000000}, |
| {REG_ESAI_TX3, 0x00000000}, |
| {REG_ESAI_TX4, 0x00000000}, |
| {REG_ESAI_TX5, 0x00000000}, |
| {REG_ESAI_TSR, 0x00000000}, |
| {REG_ESAI_SAICR, 0x00000000}, |
| {REG_ESAI_TCR, 0x00000000}, |
| {REG_ESAI_TCCR, 0x00000000}, |
| {REG_ESAI_RCR, 0x00000000}, |
| {REG_ESAI_RCCR, 0x00000000}, |
| {REG_ESAI_TSMA, 0x0000ffff}, |
| {REG_ESAI_TSMB, 0x0000ffff}, |
| {REG_ESAI_RSMA, 0x0000ffff}, |
| {REG_ESAI_RSMB, 0x0000ffff}, |
| {REG_ESAI_PRRC, 0x00000000}, |
| {REG_ESAI_PCRC, 0x00000000}, |
| }; |
| |
| static bool fsl_esai_readable_reg(struct device *dev, unsigned int reg) |
| { |
| switch (reg) { |
| case REG_ESAI_ERDR: |
| case REG_ESAI_ECR: |
| case REG_ESAI_ESR: |
| case REG_ESAI_TFCR: |
| case REG_ESAI_TFSR: |
| case REG_ESAI_RFCR: |
| case REG_ESAI_RFSR: |
| case REG_ESAI_RX0: |
| case REG_ESAI_RX1: |
| case REG_ESAI_RX2: |
| case REG_ESAI_RX3: |
| case REG_ESAI_SAISR: |
| case REG_ESAI_SAICR: |
| case REG_ESAI_TCR: |
| case REG_ESAI_TCCR: |
| case REG_ESAI_RCR: |
| case REG_ESAI_RCCR: |
| case REG_ESAI_TSMA: |
| case REG_ESAI_TSMB: |
| case REG_ESAI_RSMA: |
| case REG_ESAI_RSMB: |
| case REG_ESAI_PRRC: |
| case REG_ESAI_PCRC: |
| return true; |
| default: |
| return false; |
| } |
| } |
| |
| static bool fsl_esai_volatile_reg(struct device *dev, unsigned int reg) |
| { |
| switch (reg) { |
| case REG_ESAI_ERDR: |
| case REG_ESAI_ESR: |
| case REG_ESAI_TFSR: |
| case REG_ESAI_RFSR: |
| case REG_ESAI_RX0: |
| case REG_ESAI_RX1: |
| case REG_ESAI_RX2: |
| case REG_ESAI_RX3: |
| case REG_ESAI_SAISR: |
| return true; |
| default: |
| return false; |
| } |
| } |
| |
| static bool fsl_esai_writeable_reg(struct device *dev, unsigned int reg) |
| { |
| switch (reg) { |
| case REG_ESAI_ETDR: |
| case REG_ESAI_ECR: |
| case REG_ESAI_TFCR: |
| case REG_ESAI_RFCR: |
| case REG_ESAI_TX0: |
| case REG_ESAI_TX1: |
| case REG_ESAI_TX2: |
| case REG_ESAI_TX3: |
| case REG_ESAI_TX4: |
| case REG_ESAI_TX5: |
| case REG_ESAI_TSR: |
| case REG_ESAI_SAICR: |
| case REG_ESAI_TCR: |
| case REG_ESAI_TCCR: |
| case REG_ESAI_RCR: |
| case REG_ESAI_RCCR: |
| case REG_ESAI_TSMA: |
| case REG_ESAI_TSMB: |
| case REG_ESAI_RSMA: |
| case REG_ESAI_RSMB: |
| case REG_ESAI_PRRC: |
| case REG_ESAI_PCRC: |
| return true; |
| default: |
| return false; |
| } |
| } |
| |
| static const struct regmap_config fsl_esai_regmap_config = { |
| .reg_bits = 32, |
| .reg_stride = 4, |
| .val_bits = 32, |
| |
| .max_register = REG_ESAI_PCRC, |
| .reg_defaults = fsl_esai_reg_defaults, |
| .num_reg_defaults = ARRAY_SIZE(fsl_esai_reg_defaults), |
| .readable_reg = fsl_esai_readable_reg, |
| .volatile_reg = fsl_esai_volatile_reg, |
| .writeable_reg = fsl_esai_writeable_reg, |
| .cache_type = REGCACHE_FLAT, |
| }; |
| |
| static int fsl_esai_probe(struct platform_device *pdev) |
| { |
| struct device_node *np = pdev->dev.of_node; |
| struct fsl_esai *esai_priv; |
| struct resource *res; |
| const __be32 *iprop; |
| void __iomem *regs; |
| int irq, ret; |
| |
| esai_priv = devm_kzalloc(&pdev->dev, sizeof(*esai_priv), GFP_KERNEL); |
| if (!esai_priv) |
| return -ENOMEM; |
| |
| esai_priv->pdev = pdev; |
| strncpy(esai_priv->name, np->name, sizeof(esai_priv->name) - 1); |
| |
| /* Get the addresses and IRQ */ |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| regs = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(regs)) |
| return PTR_ERR(regs); |
| |
| esai_priv->regmap = devm_regmap_init_mmio_clk(&pdev->dev, |
| "core", regs, &fsl_esai_regmap_config); |
| if (IS_ERR(esai_priv->regmap)) { |
| dev_err(&pdev->dev, "failed to init regmap: %ld\n", |
| PTR_ERR(esai_priv->regmap)); |
| return PTR_ERR(esai_priv->regmap); |
| } |
| |
| esai_priv->coreclk = devm_clk_get(&pdev->dev, "core"); |
| if (IS_ERR(esai_priv->coreclk)) { |
| dev_err(&pdev->dev, "failed to get core clock: %ld\n", |
| PTR_ERR(esai_priv->coreclk)); |
| return PTR_ERR(esai_priv->coreclk); |
| } |
| |
| esai_priv->extalclk = devm_clk_get(&pdev->dev, "extal"); |
| if (IS_ERR(esai_priv->extalclk)) |
| dev_warn(&pdev->dev, "failed to get extal clock: %ld\n", |
| PTR_ERR(esai_priv->extalclk)); |
| |
| esai_priv->fsysclk = devm_clk_get(&pdev->dev, "fsys"); |
| if (IS_ERR(esai_priv->fsysclk)) |
| dev_warn(&pdev->dev, "failed to get fsys clock: %ld\n", |
| PTR_ERR(esai_priv->fsysclk)); |
| |
| esai_priv->spbaclk = devm_clk_get(&pdev->dev, "spba"); |
| if (IS_ERR(esai_priv->spbaclk)) |
| dev_warn(&pdev->dev, "failed to get spba clock: %ld\n", |
| PTR_ERR(esai_priv->spbaclk)); |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) { |
| dev_err(&pdev->dev, "no irq for node %s\n", pdev->name); |
| return irq; |
| } |
| |
| ret = devm_request_irq(&pdev->dev, irq, esai_isr, 0, |
| esai_priv->name, esai_priv); |
| if (ret) { |
| dev_err(&pdev->dev, "failed to claim irq %u\n", irq); |
| return ret; |
| } |
| |
| /* Set a default slot number */ |
| esai_priv->slots = 2; |
| |
| /* Set a default master/slave state */ |
| esai_priv->slave_mode = true; |
| |
| /* Determine the FIFO depth */ |
| iprop = of_get_property(np, "fsl,fifo-depth", NULL); |
| if (iprop) |
| esai_priv->fifo_depth = be32_to_cpup(iprop); |
| else |
| esai_priv->fifo_depth = 64; |
| |
| esai_priv->dma_params_tx.maxburst = 16; |
| esai_priv->dma_params_rx.maxburst = 16; |
| esai_priv->dma_params_tx.addr = res->start + REG_ESAI_ETDR; |
| esai_priv->dma_params_rx.addr = res->start + REG_ESAI_ERDR; |
| |
| esai_priv->synchronous = |
| of_property_read_bool(np, "fsl,esai-synchronous"); |
| |
| /* Implement full symmetry for synchronous mode */ |
| if (esai_priv->synchronous) { |
| fsl_esai_dai.symmetric_rates = 1; |
| fsl_esai_dai.symmetric_channels = 1; |
| fsl_esai_dai.symmetric_samplebits = 1; |
| } |
| |
| dev_set_drvdata(&pdev->dev, esai_priv); |
| |
| /* Reset ESAI unit */ |
| ret = regmap_write(esai_priv->regmap, REG_ESAI_ECR, ESAI_ECR_ERST); |
| if (ret) { |
| dev_err(&pdev->dev, "failed to reset ESAI: %d\n", ret); |
| return ret; |
| } |
| |
| /* |
| * We need to enable ESAI so as to access some of its registers. |
| * Otherwise, we would fail to dump regmap from user space. |
| */ |
| ret = regmap_write(esai_priv->regmap, REG_ESAI_ECR, ESAI_ECR_ESAIEN); |
| if (ret) { |
| dev_err(&pdev->dev, "failed to enable ESAI: %d\n", ret); |
| return ret; |
| } |
| |
| esai_priv->tx_mask = 0xFFFFFFFF; |
| esai_priv->rx_mask = 0xFFFFFFFF; |
| |
| /* Clear the TSMA, TSMB, RSMA, RSMB */ |
| regmap_write(esai_priv->regmap, REG_ESAI_TSMA, 0); |
| regmap_write(esai_priv->regmap, REG_ESAI_TSMB, 0); |
| regmap_write(esai_priv->regmap, REG_ESAI_RSMA, 0); |
| regmap_write(esai_priv->regmap, REG_ESAI_RSMB, 0); |
| |
| ret = devm_snd_soc_register_component(&pdev->dev, &fsl_esai_component, |
| &fsl_esai_dai, 1); |
| if (ret) { |
| dev_err(&pdev->dev, "failed to register DAI: %d\n", ret); |
| return ret; |
| } |
| |
| ret = imx_pcm_dma_init(pdev, IMX_ESAI_DMABUF_SIZE); |
| if (ret) |
| dev_err(&pdev->dev, "failed to init imx pcm dma: %d\n", ret); |
| |
| return ret; |
| } |
| |
| static const struct of_device_id fsl_esai_dt_ids[] = { |
| { .compatible = "fsl,imx35-esai", }, |
| { .compatible = "fsl,vf610-esai", }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(of, fsl_esai_dt_ids); |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int fsl_esai_suspend(struct device *dev) |
| { |
| struct fsl_esai *esai = dev_get_drvdata(dev); |
| |
| regcache_cache_only(esai->regmap, true); |
| regcache_mark_dirty(esai->regmap); |
| |
| return 0; |
| } |
| |
| static int fsl_esai_resume(struct device *dev) |
| { |
| struct fsl_esai *esai = dev_get_drvdata(dev); |
| int ret; |
| |
| regcache_cache_only(esai->regmap, false); |
| |
| /* FIFO reset for safety */ |
| regmap_update_bits(esai->regmap, REG_ESAI_TFCR, |
| ESAI_xFCR_xFR, ESAI_xFCR_xFR); |
| regmap_update_bits(esai->regmap, REG_ESAI_RFCR, |
| ESAI_xFCR_xFR, ESAI_xFCR_xFR); |
| |
| ret = regcache_sync(esai->regmap); |
| if (ret) |
| return ret; |
| |
| /* FIFO reset done */ |
| regmap_update_bits(esai->regmap, REG_ESAI_TFCR, ESAI_xFCR_xFR, 0); |
| regmap_update_bits(esai->regmap, REG_ESAI_RFCR, ESAI_xFCR_xFR, 0); |
| |
| return 0; |
| } |
| #endif /* CONFIG_PM_SLEEP */ |
| |
| static const struct dev_pm_ops fsl_esai_pm_ops = { |
| SET_SYSTEM_SLEEP_PM_OPS(fsl_esai_suspend, fsl_esai_resume) |
| }; |
| |
| static struct platform_driver fsl_esai_driver = { |
| .probe = fsl_esai_probe, |
| .driver = { |
| .name = "fsl-esai-dai", |
| .pm = &fsl_esai_pm_ops, |
| .of_match_table = fsl_esai_dt_ids, |
| }, |
| }; |
| |
| module_platform_driver(fsl_esai_driver); |
| |
| MODULE_AUTHOR("Freescale Semiconductor, Inc."); |
| MODULE_DESCRIPTION("Freescale ESAI CPU DAI driver"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_ALIAS("platform:fsl-esai-dai"); |