| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * dts file for Xilinx ZynqMP ZCU106 |
| * |
| * (C) Copyright 2016, Xilinx, Inc. |
| * |
| * Michal Simek <michal.simek@xilinx.com> |
| */ |
| |
| /dts-v1/; |
| |
| #include "zynqmp.dtsi" |
| #include "zynqmp-clk.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/gpio/gpio.h> |
| |
| / { |
| model = "ZynqMP ZCU106 RevA"; |
| compatible = "xlnx,zynqmp-zcu106-revA", "xlnx,zynqmp-zcu106", "xlnx,zynqmp"; |
| |
| aliases { |
| ethernet0 = &gem3; |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| mmc0 = &sdhci1; |
| rtc0 = &rtc; |
| serial0 = &uart0; |
| serial1 = &uart1; |
| serial2 = &dcc; |
| }; |
| |
| chosen { |
| bootargs = "earlycon"; |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| memory@0 { |
| device_type = "memory"; |
| reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| autorepeat; |
| sw19 { |
| label = "sw19"; |
| gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; |
| linux,code = <KEY_DOWN>; |
| gpio-key,wakeup; |
| autorepeat; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| heartbeat-led { |
| label = "heartbeat"; |
| gpios = <&gpio 23 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| }; |
| }; |
| |
| &can1 { |
| status = "okay"; |
| }; |
| |
| &dcc { |
| status = "okay"; |
| }; |
| |
| /* fpd_dma clk 667MHz, lpd_dma 500MHz */ |
| &fpd_dma_chan1 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan2 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan3 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan4 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan5 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan6 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan7 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan8 { |
| status = "okay"; |
| }; |
| |
| &gem3 { |
| status = "okay"; |
| phy-handle = <&phy0>; |
| phy-mode = "rgmii-id"; |
| phy0: phy@c { |
| reg = <0xc>; |
| ti,rx-internal-delay = <0x8>; |
| ti,tx-internal-delay = <0xa>; |
| ti,fifo-depth = <0x1>; |
| }; |
| }; |
| |
| &gpio { |
| status = "okay"; |
| }; |
| |
| &i2c0 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| tca6416_u97: gpio@20 { |
| compatible = "ti,tca6416"; |
| reg = <0x20>; |
| gpio-controller; /* interrupt not connected */ |
| #gpio-cells = <2>; |
| /* |
| * IRQ not connected |
| * Lines: |
| * 0 - SFP_SI5328_INT_ALM |
| * 1 - HDMI_SI5328_INT_ALM |
| * 5 - IIC_MUX_RESET_B |
| * 6 - GEM3_EXP_RESET_B |
| * 10 - FMC_HPC0_PRSNT_M2C_B |
| * 11 - FMC_HPC1_PRSNT_M2C_B |
| * 2-4, 7, 12-17 - not connected |
| */ |
| }; |
| |
| tca6416_u61: gpio@21 { |
| compatible = "ti,tca6416"; |
| reg = <0x21>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| /* |
| * IRQ not connected |
| * Lines: |
| * 0 - VCCPSPLL_EN |
| * 1 - MGTRAVCC_EN |
| * 2 - MGTRAVTT_EN |
| * 3 - VCCPSDDRPLL_EN |
| * 4 - MIO26_PMU_INPUT_LS |
| * 5 - PL_PMBUS_ALERT |
| * 6 - PS_PMBUS_ALERT |
| * 7 - MAXIM_PMBUS_ALERT |
| * 10 - PL_DDR4_VTERM_EN |
| * 11 - PL_DDR4_VPP_2V5_EN |
| * 12 - PS_DIMM_VDDQ_TO_PSVCCO_ON |
| * 13 - PS_DIMM_SUSPEND_EN |
| * 14 - PS_DDR4_VTERM_EN |
| * 15 - PS_DDR4_VPP_2V5_EN |
| * 16 - 17 - not connected |
| */ |
| }; |
| |
| i2c-mux@75 { /* u60 */ |
| compatible = "nxp,pca9544"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x75>; |
| i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| /* PS_PMBUS */ |
| ina226@40 { /* u76 */ |
| compatible = "ti,ina226"; |
| reg = <0x40>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@41 { /* u77 */ |
| compatible = "ti,ina226"; |
| reg = <0x41>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@42 { /* u78 */ |
| compatible = "ti,ina226"; |
| reg = <0x42>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@43 { /* u87 */ |
| compatible = "ti,ina226"; |
| reg = <0x43>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@44 { /* u85 */ |
| compatible = "ti,ina226"; |
| reg = <0x44>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@45 { /* u86 */ |
| compatible = "ti,ina226"; |
| reg = <0x45>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@46 { /* u93 */ |
| compatible = "ti,ina226"; |
| reg = <0x46>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@47 { /* u88 */ |
| compatible = "ti,ina226"; |
| reg = <0x47>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@4a { /* u15 */ |
| compatible = "ti,ina226"; |
| reg = <0x4a>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@4b { /* u92 */ |
| compatible = "ti,ina226"; |
| reg = <0x4b>; |
| shunt-resistor = <5000>; |
| }; |
| }; |
| i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| /* PL_PMBUS */ |
| ina226@40 { /* u79 */ |
| compatible = "ti,ina226"; |
| reg = <0x40>; |
| shunt-resistor = <2000>; |
| }; |
| ina226@41 { /* u81 */ |
| compatible = "ti,ina226"; |
| reg = <0x41>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@42 { /* u80 */ |
| compatible = "ti,ina226"; |
| reg = <0x42>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@43 { /* u84 */ |
| compatible = "ti,ina226"; |
| reg = <0x43>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@44 { /* u16 */ |
| compatible = "ti,ina226"; |
| reg = <0x44>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@45 { /* u65 */ |
| compatible = "ti,ina226"; |
| reg = <0x45>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@46 { /* u74 */ |
| compatible = "ti,ina226"; |
| reg = <0x46>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@47 { /* u75 */ |
| compatible = "ti,ina226"; |
| reg = <0x47>; |
| shunt-resistor = <5000>; |
| }; |
| }; |
| i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| /* MAXIM_PMBUS - 00 */ |
| max15301@a { /* u46 */ |
| compatible = "maxim,max15301"; |
| reg = <0xa>; |
| }; |
| max15303@b { /* u4 */ |
| compatible = "maxim,max15303"; |
| reg = <0xb>; |
| }; |
| max15303@10 { /* u13 */ |
| compatible = "maxim,max15303"; |
| reg = <0x10>; |
| }; |
| max15301@13 { /* u47 */ |
| compatible = "maxim,max15301"; |
| reg = <0x13>; |
| }; |
| max15303@14 { /* u7 */ |
| compatible = "maxim,max15303"; |
| reg = <0x14>; |
| }; |
| max15303@15 { /* u6 */ |
| compatible = "maxim,max15303"; |
| reg = <0x15>; |
| }; |
| max15303@16 { /* u10 */ |
| compatible = "maxim,max15303"; |
| reg = <0x16>; |
| }; |
| max15303@17 { /* u9 */ |
| compatible = "maxim,max15303"; |
| reg = <0x17>; |
| }; |
| max15301@18 { /* u63 */ |
| compatible = "maxim,max15301"; |
| reg = <0x18>; |
| }; |
| max15303@1a { /* u49 */ |
| compatible = "maxim,max15303"; |
| reg = <0x1a>; |
| }; |
| max15303@1b { /* u8 */ |
| compatible = "maxim,max15303"; |
| reg = <0x1b>; |
| }; |
| max15303@1d { /* u18 */ |
| compatible = "maxim,max15303"; |
| reg = <0x1d>; |
| }; |
| |
| max20751@72 { /* u95 */ |
| compatible = "maxim,max20751"; |
| reg = <0x72>; |
| }; |
| max20751@73 { /* u96 */ |
| compatible = "maxim,max20751"; |
| reg = <0x73>; |
| }; |
| }; |
| /* Bus 3 is not connected */ |
| }; |
| }; |
| |
| &i2c1 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| /* PL i2c via PCA9306 - u45 */ |
| i2c-mux@74 { /* u34 */ |
| compatible = "nxp,pca9548"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x74>; |
| i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| /* |
| * IIC_EEPROM 1kB memory which uses 256B blocks |
| * where every block has different address. |
| * 0 - 256B address 0x54 |
| * 256B - 512B address 0x55 |
| * 512B - 768B address 0x56 |
| * 768B - 1024B address 0x57 |
| */ |
| eeprom: eeprom@54 { /* u23 */ |
| compatible = "atmel,24c08"; |
| reg = <0x54>; |
| }; |
| }; |
| i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| si5341: clock-generator@36 { /* SI5341 - u69 */ |
| reg = <0x36>; |
| }; |
| |
| }; |
| i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| si570_1: clock-generator@5d { /* USER SI570 - u42 */ |
| #clock-cells = <0>; |
| compatible = "silabs,si570"; |
| reg = <0x5d>; |
| temperature-stability = <50>; |
| factory-fout = <300000000>; |
| clock-frequency = <300000000>; |
| }; |
| }; |
| i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| si570_2: clock-generator@5d { /* USER MGT SI570 - u56 */ |
| #clock-cells = <0>; |
| compatible = "silabs,si570"; |
| reg = <0x5d>; |
| temperature-stability = <50>; /* copy from zc702 */ |
| factory-fout = <156250000>; |
| clock-frequency = <148500000>; |
| }; |
| }; |
| i2c@4 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <4>; |
| si5328: clock-generator@69 {/* SI5328 - u20 */ |
| reg = <0x69>; |
| }; |
| }; |
| i2c@5 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <5>; /* FAN controller */ |
| temp@4c {/* lm96163 - u128 */ |
| compatible = "national,lm96163"; |
| reg = <0x4c>; |
| }; |
| }; |
| /* 6 - 7 unconnected */ |
| }; |
| |
| i2c-mux@75 { |
| compatible = "nxp,pca9548"; /* u135 */ |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x75>; |
| |
| i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| /* HPC0_IIC */ |
| }; |
| i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| /* HPC1_IIC */ |
| }; |
| i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| /* SYSMON */ |
| }; |
| i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| /* DDR4 SODIMM */ |
| }; |
| i2c@4 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <4>; |
| /* SEP 3 */ |
| }; |
| i2c@5 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <5>; |
| /* SEP 2 */ |
| }; |
| i2c@6 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <6>; |
| /* SEP 1 */ |
| }; |
| i2c@7 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <7>; |
| /* SEP 0 */ |
| }; |
| }; |
| }; |
| |
| &rtc { |
| status = "okay"; |
| }; |
| |
| &sata { |
| status = "okay"; |
| /* SATA OOB timing settings */ |
| ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; |
| ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; |
| ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; |
| ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>; |
| ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; |
| ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; |
| ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; |
| ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; |
| }; |
| |
| /* SD1 with level shifter */ |
| &sdhci1 { |
| status = "okay"; |
| no-1-8-v; |
| }; |
| |
| &uart0 { |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| status = "okay"; |
| }; |
| |
| /* ULPI SMSC USB3320 */ |
| &usb0 { |
| status = "okay"; |
| }; |
| |
| &watchdog0 { |
| status = "okay"; |
| }; |
