| /* |
| * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include "msm8996.dtsi" |
| #include "pm8994.dtsi" |
| #include "pmi8994.dtsi" |
| #include "apq8096-db820c-pins.dtsi" |
| #include "apq8096-db820c-pmic-pins.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/gpio/gpio.h> |
| |
| /* |
| * GPIO name legend: proper name = the GPIO line is used as GPIO |
| * NC = not connected (pin out but not routed from the chip to |
| * anything the board) |
| * "[PER]" = pin is muxed for [peripheral] (not GPIO) |
| * LSEC = Low Speed External Connector |
| * P HSEC = Primary High Speed External Connector |
| * S HSEC = Secondary High Speed External Connector |
| * J14 = Camera Connector |
| * TP = Test Points |
| * |
| * Line names are taken from the schematic "DragonBoard 820c", |
| * drawing no: LM25-P2751-1 |
| * |
| * For the lines routed to the external connectors the |
| * lines are named after the 96Boards CE Specification 1.0, |
| * Appendix "Expansion Connector Signal Description". |
| * |
| * When the 96Board naming of a line and the schematic name of |
| * the same line are in conflict, the 96Board specification |
| * takes precedence, which means that the external UART on the |
| * LSEC is named UART0 while the schematic and SoC names this |
| * UART3. This is only for the informational lines i.e. "[FOO]", |
| * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only |
| * ones actually used for GPIO. |
| */ |
| |
| / { |
| aliases { |
| serial0 = &blsp2_uart1; |
| serial1 = &blsp2_uart2; |
| serial2 = &blsp1_uart1; |
| i2c0 = &blsp1_i2c2; |
| i2c1 = &blsp2_i2c1; |
| i2c2 = &blsp2_i2c0; |
| spi0 = &blsp1_spi0; |
| spi1 = &blsp2_spi5; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| clocks { |
| divclk4: divclk4 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| clock-output-names = "divclk4"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&divclk4_pin_a>; |
| }; |
| }; |
| |
| soc { |
| serial@7570000 { |
| label = "BT-UART"; |
| status = "okay"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp1_uart1_default>; |
| pinctrl-1 = <&blsp1_uart1_sleep>; |
| |
| bluetooth { |
| compatible = "qcom,qca6174-bt"; |
| |
| /* bt_disable_n gpio */ |
| enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; |
| |
| clocks = <&divclk4>; |
| }; |
| }; |
| |
| serial@75b0000 { |
| label = "LS-UART1"; |
| status = "okay"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp2_uart1_2pins_default>; |
| pinctrl-1 = <&blsp2_uart1_2pins_sleep>; |
| }; |
| |
| serial@75b1000 { |
| label = "LS-UART0"; |
| status = "disabled"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp2_uart2_4pins_default>; |
| pinctrl-1 = <&blsp2_uart2_4pins_sleep>; |
| }; |
| |
| i2c@7577000 { |
| /* On Low speed expansion */ |
| label = "LS-I2C0"; |
| status = "okay"; |
| }; |
| |
| i2c@75b6000 { |
| /* On Low speed expansion */ |
| label = "LS-I2C1"; |
| status = "okay"; |
| }; |
| |
| spi@7575000 { |
| /* On Low speed expansion */ |
| label = "LS-SPI0"; |
| status = "okay"; |
| }; |
| |
| i2c@75b5000 { |
| /* On High speed expansion */ |
| label = "HS-I2C2"; |
| status = "okay"; |
| }; |
| |
| spi@75ba000{ |
| /* On High speed expansion */ |
| label = "HS-SPI1"; |
| status = "okay"; |
| }; |
| |
| sdhci@74a4900 { |
| /* External SD card */ |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; |
| pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; |
| cd-gpios = <&msmgpio 38 0x1>; |
| vmmc-supply = <&pm8994_l21>; |
| vqmmc-supply = <&pm8994_l13>; |
| status = "okay"; |
| }; |
| |
| phy@627000 { |
| status = "okay"; |
| }; |
| |
| ufshc@624000 { |
| status = "okay"; |
| }; |
| |
| pinctrl@1010000 { |
| gpio-line-names = |
| "[SPI0_DOUT]", /* GPIO_0, BLSP1_SPI_MOSI, LSEC pin 14 */ |
| "[SPI0_DIN]", /* GPIO_1, BLSP1_SPI_MISO, LSEC pin 10 */ |
| "[SPI0_CS]", /* GPIO_2, BLSP1_SPI_CS_N, LSEC pin 12 */ |
| "[SPI0_SCLK]", /* GPIO_3, BLSP1_SPI_CLK, LSEC pin 8 */ |
| "[UART1_TxD]", /* GPIO_4, BLSP8_UART_TX, LSEC pin 11 */ |
| "[UART1_RxD]", /* GPIO_5, BLSP8_UART_RX, LSEC pin 13 */ |
| "[I2C1_SDA]", /* GPIO_6, BLSP8_I2C_SDA, LSEC pin 21 */ |
| "[I2C1_SCL]", /* GPIO_7, BLSP8_I2C_SCL, LSEC pin 19 */ |
| "GPIO-H", /* GPIO_8, LCD0_RESET_N, LSEC pin 30 */ |
| "TP93", /* GPIO_9 */ |
| "GPIO-G", /* GPIO_10, MDP_VSYNC_P, LSEC pin 29 */ |
| "[MDP_VSYNC_S]", /* GPIO_11, S HSEC pin 55 */ |
| "NC", /* GPIO_12 */ |
| "[CSI0_MCLK]", /* GPIO_13, CAM_MCLK0, P HSEC pin 15 */ |
| "[CAM_MCLK1]", /* GPIO_14, J14 pin 11 */ |
| "[CSI1_MCLK]", /* GPIO_15, CAM_MCLK2, P HSEC pin 17 */ |
| "TP99", /* GPIO_16 */ |
| "[I2C2_SDA]", /* GPIO_17, CCI_I2C_SDA0, P HSEC pin 34 */ |
| "[I2C2_SCL]", /* GPIO_18, CCI_I2C_SCL0, P HSEC pin 32 */ |
| "[CCI_I2C_SDA1]", /* GPIO_19, S HSEC pin 38 */ |
| "[CCI_I2C_SCL1]", /* GPIO_20, S HSEC pin 36 */ |
| "FLASH_STROBE_EN", /* GPIO_21, S HSEC pin 5 */ |
| "FLASH_STROBE_TRIG", /* GPIO_22, S HSEC pin 1 */ |
| "GPIO-K", /* GPIO_23, CAM2_RST_N, LSEC pin 33 */ |
| "GPIO-D", /* GPIO_24, LSEC pin 26 */ |
| "GPIO-I", /* GPIO_25, CAM0_RST_N, LSEC pin 31 */ |
| "GPIO-J", /* GPIO_26, CAM0_STANDBY_N, LSEC pin 32 */ |
| "BLSP6_I2C_SDA", /* GPIO_27 */ |
| "BLSP6_I2C_SCL", /* GPIO_28 */ |
| "GPIO-B", /* GPIO_29, TS0_RESET_N, LSEC pin 24 */ |
| "GPIO30", /* GPIO_30, S HSEC pin 4 */ |
| "HDMI_CEC", /* GPIO_31 */ |
| "HDMI_DDC_CLOCK", /* GPIO_32 */ |
| "HDMI_DDC_DATA", /* GPIO_33 */ |
| "HDMI_HOT_PLUG_DETECT", /* GPIO_34 */ |
| "PCIE0_RST_N", /* GPIO_35 */ |
| "PCIE0_CLKREQ_N", /* GPIO_36 */ |
| "PCIE0_WAKE", /* GPIO_37 */ |
| "SD_CARD_DET_N", /* GPIO_38 */ |
| "TSIF1_SYNC", /* GPIO_39, S HSEC pin 48 */ |
| "W_DISABLE_N", /* GPIO_40 */ |
| "[BLSP9_UART_TX]", /* GPIO_41 */ |
| "[BLSP9_UART_RX]", /* GPIO_42 */ |
| "[BLSP2_UART_CTS_N]", /* GPIO_43 */ |
| "[BLSP2_UART_RFR_N]", /* GPIO_44 */ |
| "[BLSP3_UART_TX]", /* GPIO_45 */ |
| "[BLSP3_UART_RX]", /* GPIO_46 */ |
| "[I2C0_SDA]", /* GPIO_47, LS_I2C0_SDA, LSEC pin 17 */ |
| "[I2C0_SCL]", /* GPIO_48, LS_I2C0_SCL, LSEC pin 15 */ |
| "[UART0_TxD]", /* GPIO_49, BLSP9_UART_TX, LSEC pin 5 */ |
| "[UART0_RxD]", /* GPIO_50, BLSP9_UART_RX, LSEC pin 7 */ |
| "[UART0_CTS]", /* GPIO_51, BLSP9_UART_CTS_N, LSEC pin 3 */ |
| "[UART0_RTS]", /* GPIO_52, BLSP9_UART_RFR_N, LSEC pin 9 */ |
| "[CODEC_INT1_N]", /* GPIO_53 */ |
| "[CODEC_INT2_N]", /* GPIO_54 */ |
| "[BLSP7_I2C_SDA]", /* GPIO_55 */ |
| "[BLSP7_I2C_SCL]", /* GPIO_56 */ |
| "MI2S_MCLK", /* GPIO_57, S HSEC pin 3 */ |
| "[PCM_CLK]", /* GPIO_58, QUA_MI2S_SCK, LSEC pin 18 */ |
| "[PCM_FS]", /* GPIO_59, QUA_MI2S_WS, LSEC pin 16 */ |
| "[PCM_DO]", /* GPIO_60, QUA_MI2S_DATA0, LSEC pin 20 */ |
| "[PCM_DI]", /* GPIO_61, QUA_MI2S_DATA1, LSEC pin 22 */ |
| "GPIO-E", /* GPIO_62, LSEC pin 27 */ |
| "TP87", /* GPIO_63 */ |
| "[CODEC_RST_N]", /* GPIO_64 */ |
| "[PCM1_CLK]", /* GPIO_65 */ |
| "[PCM1_SYNC]", /* GPIO_66 */ |
| "[PCM1_DIN]", /* GPIO_67 */ |
| "[PCM1_DOUT]", /* GPIO_68 */ |
| "AUDIO_REF_CLK", /* GPIO_69 */ |
| "SLIMBUS_CLK", /* GPIO_70 */ |
| "SLIMBUS_DATA0", /* GPIO_71 */ |
| "SLIMBUS_DATA1", /* GPIO_72 */ |
| "NC", /* GPIO_73 */ |
| "NC", /* GPIO_74 */ |
| "NC", /* GPIO_75 */ |
| "NC", /* GPIO_76 */ |
| "TP94", /* GPIO_77 */ |
| "NC", /* GPIO_78 */ |
| "TP95", /* GPIO_79 */ |
| "GPIO-A", /* GPIO_80, MEMS_RESET_N, LSEC pin 23 */ |
| "TP88", /* GPIO_81 */ |
| "TP89", /* GPIO_82 */ |
| "TP90", /* GPIO_83 */ |
| "TP91", /* GPIO_84 */ |
| "[SD_DAT0]", /* GPIO_85, BLSP12_SPI_MOSI, P HSEC pin 1 */ |
| "[SD_CMD]", /* GPIO_86, BLSP12_SPI_MISO, P HSEC pin 11 */ |
| "[SD_DAT3]", /* GPIO_87, BLSP12_SPI_CS_N, P HSEC pin 7 */ |
| "[SD_SCLK]", /* GPIO_88, BLSP12_SPI_CLK, P HSEC pin 9 */ |
| "TSIF1_CLK", /* GPIO_89, S HSEC pin 42 */ |
| "TSIF1_EN", /* GPIO_90, S HSEC pin 46 */ |
| "TSIF1_DATA", /* GPIO_91, S HSEC pin 44 */ |
| "NC", /* GPIO_92 */ |
| "TSIF2_CLK", /* GPIO_93, S HSEC pin 52 */ |
| "TSIF2_EN", /* GPIO_94, S HSEC pin 56 */ |
| "TSIF2_DATA", /* GPIO_95, S HSEC pin 54 */ |
| "TSIF2_SYNC", /* GPIO_96, S HSEC pin 58 */ |
| "NC", /* GPIO_97 */ |
| "CAM1_STANDBY_N", /* GPIO_98 */ |
| "NC", /* GPIO_99 */ |
| "NC", /* GPIO_100 */ |
| "[LCD1_RESET_N]", /* GPIO_101, S HSEC pin 51 */ |
| "BOOT_CONFIG1", /* GPIO_102 */ |
| "USB_HUB_RESET", /* GPIO_103 */ |
| "CAM1_RST_N", /* GPIO_104 */ |
| "NC", /* GPIO_105 */ |
| "NC", /* GPIO_106 */ |
| "NC", /* GPIO_107 */ |
| "NC", /* GPIO_108 */ |
| "NC", /* GPIO_109 */ |
| "NC", /* GPIO_110 */ |
| "NC", /* GPIO_111 */ |
| "NC", /* GPIO_112 */ |
| "PMI8994_BUA", /* GPIO_113 */ |
| "PCIE2_RST_N", /* GPIO_114 */ |
| "PCIE2_CLKREQ_N", /* GPIO_115 */ |
| "PCIE2_WAKE", /* GPIO_116 */ |
| "SSC_IRQ_0", /* GPIO_117 */ |
| "SSC_IRQ_1", /* GPIO_118 */ |
| "SSC_IRQ_2", /* GPIO_119 */ |
| "NC", /* GPIO_120 */ |
| "GPIO121", /* GPIO_121, S HSEC pin 2 */ |
| "NC", /* GPIO_122 */ |
| "SSC_IRQ_6", /* GPIO_123 */ |
| "SSC_IRQ_7", /* GPIO_124 */ |
| "GPIO-C", /* GPIO_125, TS_INT0, LSEC pin 25 */ |
| "BOOT_CONFIG5", /* GPIO_126 */ |
| "NC", /* GPIO_127 */ |
| "NC", /* GPIO_128 */ |
| "BOOT_CONFIG7", /* GPIO_129 */ |
| "PCIE1_RST_N", /* GPIO_130 */ |
| "PCIE1_CLKREQ_N", /* GPIO_131 */ |
| "PCIE1_WAKE", /* GPIO_132 */ |
| "GPIO-L", /* GPIO_133, CAM2_STANDBY_N, LSEC pin 34 */ |
| "NC", /* GPIO_134 */ |
| "NC", /* GPIO_135 */ |
| "BOOT_CONFIG8", /* GPIO_136 */ |
| "NC", /* GPIO_137 */ |
| "NC", /* GPIO_138 */ |
| "GPS_SSBI2", /* GPIO_139 */ |
| "GPS_SSBI1", /* GPIO_140 */ |
| "NC", /* GPIO_141 */ |
| "NC", /* GPIO_142 */ |
| "NC", /* GPIO_143 */ |
| "BOOT_CONFIG6", /* GPIO_144 */ |
| "NC", /* GPIO_145 */ |
| "NC", /* GPIO_146 */ |
| "NC", /* GPIO_147 */ |
| "NC", /* GPIO_148 */ |
| "NC"; /* GPIO_149 */ |
| }; |
| |
| qcom,spmi@400f000 { |
| pmic@0 { |
| gpios@c000 { |
| gpio-line-names = |
| "NC", |
| "KEY_VOLP_N", |
| "NC", |
| "BL1_PWM", |
| "GPIO-F", /* BL0_PWM, LSEC pin 28 */ |
| "BL1_EN", |
| "NC", |
| "WLAN_EN", |
| "NC", |
| "NC", |
| "NC", |
| "NC", |
| "NC", |
| "NC", |
| "DIVCLK1", |
| "DIVCLK2", |
| "DIVCLK3", |
| "DIVCLK4", |
| "BT_EN", |
| "PMIC_SLB", |
| "PMIC_BUA", |
| "USB_VBUS_DET"; |
| }; |
| |
| mpps@a000 { |
| gpio-line-names = |
| "VDDPX_BIAS", |
| "WIFI_LED", |
| "NC", |
| "BT_LED", |
| "PM_MPP05", |
| "PM_MPP06", |
| "PM_MPP07", |
| "NC"; |
| }; |
| }; |
| |
| pmic@2 { |
| gpios@c000 { |
| gpio-line-names = |
| "NC", |
| "SPKR_AMP_EN1", |
| "SPKR_AMP_EN2", |
| "TP61", |
| "NC", |
| "USB2_VBUS_DET", |
| "NC", |
| "NC", |
| "NC", |
| "NC"; |
| }; |
| }; |
| }; |
| |
| phy@34000 { |
| status = "okay"; |
| }; |
| |
| phy@7410000 { |
| status = "okay"; |
| }; |
| |
| phy@7411000 { |
| status = "okay"; |
| }; |
| |
| phy@7412000 { |
| status = "okay"; |
| }; |
| |
| usb@6a00000 { |
| status = "okay"; |
| |
| dwc3@6a00000 { |
| extcon = <&usb3_id>; |
| dr_mode = "otg"; |
| }; |
| }; |
| |
| usb3_id: usb3-id { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpio = <&pm8994_gpios 22 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb3_vbus_det_gpio>; |
| }; |
| |
| usb@7600000 { |
| status = "okay"; |
| |
| dwc3@7600000 { |
| extcon = <&usb2_id>; |
| dr_mode = "otg"; |
| maximum-speed = "high-speed"; |
| }; |
| }; |
| |
| usb2_id: usb2-id { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpio = <&pmi8994_gpios 6 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb2_vbus_det_gpio>; |
| }; |
| |
| wlan_en: wlan-en-1-8v { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_en_gpios>; |
| compatible = "regulator-fixed"; |
| regulator-name = "wlan-en-regulator"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| gpio = <&pm8994_gpios 8 0>; |
| |
| /* WLAN card specific delay */ |
| startup-delay-us = <70000>; |
| enable-active-high; |
| }; |
| |
| agnoc@0 { |
| pcie@600000 { |
| status = "okay"; |
| perst-gpio = <&msmgpio 35 GPIO_ACTIVE_LOW>; |
| vddpe-3v3-supply = <&wlan_en>; |
| }; |
| |
| pcie@608000 { |
| status = "okay"; |
| perst-gpio = <&msmgpio 130 GPIO_ACTIVE_LOW>; |
| }; |
| |
| pcie@610000 { |
| status = "okay"; |
| perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| }; |
| |
| |
| gpio_keys { |
| compatible = "gpio-keys"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| autorepeat; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&volume_up_gpio>; |
| |
| button@0 { |
| label = "Volume Up"; |
| linux,code = <KEY_VOLUMEUP>; |
| gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| rpm-glink { |
| rpm_requests { |
| pm8994-regulators { |
| vdd_l1-supply = <&pm8994_s3>; |
| vdd_l2_l26_l28-supply = <&pm8994_s3>; |
| vdd_l3_l11-supply = <&pm8994_s3>; |
| vdd_l4_l27_l31-supply = <&pm8994_s3>; |
| vdd_l5_l7-supply = <&pm8994_s5>; |
| vdd_l14_l15-supply = <&pm8994_s5>; |
| vdd_l20_l21-supply = <&pm8994_s5>; |
| vdd_l25-supply = <&pm8994_s3>; |
| |
| s3 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| |
| /** |
| * 1.8v required on LS expansion |
| * for mezzanine boards |
| */ |
| s4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |
| s5 { |
| regulator-min-microvolt = <2150000>; |
| regulator-max-microvolt = <2150000>; |
| }; |
| s7 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| }; |
| |
| l1 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| }; |
| l2 { |
| regulator-min-microvolt = <1250000>; |
| regulator-max-microvolt = <1250000>; |
| }; |
| l3 { |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <850000>; |
| }; |
| l4 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| l6 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| l8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| l9 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| l10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| l11 { |
| regulator-min-microvolt = <1150000>; |
| regulator-max-microvolt = <1150000>; |
| }; |
| l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| l13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| l14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| l15 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| l16 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| l17 { |
| regulator-min-microvolt = <2500000>; |
| regulator-max-microvolt = <2500000>; |
| }; |
| l18 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2900000>; |
| }; |
| l19 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| l20 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-allow-set-load; |
| }; |
| l21 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-allow-set-load; |
| regulator-system-load = <200000>; |
| }; |
| l22 { |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| l23 { |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| l24 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| }; |
| l25 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-allow-set-load; |
| }; |
| l27 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| }; |
| l28 { |
| regulator-min-microvolt = <925000>; |
| regulator-max-microvolt = <925000>; |
| regulator-allow-set-load; |
| }; |
| l29 { |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| l30 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| l32 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| }; |
| }; |
| }; |
| }; |
