| /* | |
| * GPIO Abstraction Layer | |
| * | |
| * Copyright 2006-2010 Analog Devices Inc. | |
| * | |
| * Licensed under the GPL-2 or later | |
| */ | |
| #include <linux/delay.h> | |
| #include <linux/module.h> | |
| #include <linux/err.h> | |
| #include <linux/proc_fs.h> | |
| #include <linux/seq_file.h> | |
| #include <linux/gpio.h> | |
| #include <linux/irq.h> | |
| #if ANOMALY_05000311 || ANOMALY_05000323 | |
| enum { | |
| AWA_data = SYSCR, | |
| AWA_data_clear = SYSCR, | |
| AWA_data_set = SYSCR, | |
| AWA_toggle = SYSCR, | |
| AWA_maska = BFIN_UART_SCR, | |
| AWA_maska_clear = BFIN_UART_SCR, | |
| AWA_maska_set = BFIN_UART_SCR, | |
| AWA_maska_toggle = BFIN_UART_SCR, | |
| AWA_maskb = BFIN_UART_GCTL, | |
| AWA_maskb_clear = BFIN_UART_GCTL, | |
| AWA_maskb_set = BFIN_UART_GCTL, | |
| AWA_maskb_toggle = BFIN_UART_GCTL, | |
| AWA_dir = SPORT1_STAT, | |
| AWA_polar = SPORT1_STAT, | |
| AWA_edge = SPORT1_STAT, | |
| AWA_both = SPORT1_STAT, | |
| #if ANOMALY_05000311 | |
| AWA_inen = TIMER_ENABLE, | |
| #elif ANOMALY_05000323 | |
| AWA_inen = DMA1_1_CONFIG, | |
| #endif | |
| }; | |
| /* Anomaly Workaround */ | |
| #define AWA_DUMMY_READ(name) bfin_read16(AWA_ ## name) | |
| #else | |
| #define AWA_DUMMY_READ(...) do { } while (0) | |
| #endif | |
| static struct gpio_port_t * const gpio_array[] = { | |
| #if defined(BF533_FAMILY) || defined(BF538_FAMILY) | |
| (struct gpio_port_t *) FIO_FLAG_D, | |
| #elif defined(CONFIG_BF52x) || defined(BF537_FAMILY) || defined(CONFIG_BF51x) | |
| (struct gpio_port_t *) PORTFIO, | |
| (struct gpio_port_t *) PORTGIO, | |
| (struct gpio_port_t *) PORTHIO, | |
| #elif defined(BF561_FAMILY) | |
| (struct gpio_port_t *) FIO0_FLAG_D, | |
| (struct gpio_port_t *) FIO1_FLAG_D, | |
| (struct gpio_port_t *) FIO2_FLAG_D, | |
| #else | |
| # error no gpio arrays defined | |
| #endif | |
| }; | |
| #if defined(CONFIG_BF52x) || defined(BF537_FAMILY) || defined(CONFIG_BF51x) | |
| static unsigned short * const port_fer[] = { | |
| (unsigned short *) PORTF_FER, | |
| (unsigned short *) PORTG_FER, | |
| (unsigned short *) PORTH_FER, | |
| }; | |
| # if !defined(BF537_FAMILY) | |
| static unsigned short * const port_mux[] = { | |
| (unsigned short *) PORTF_MUX, | |
| (unsigned short *) PORTG_MUX, | |
| (unsigned short *) PORTH_MUX, | |
| }; | |
| static const | |
| u8 pmux_offset[][16] = { | |
| # if defined(CONFIG_BF52x) | |
| { 0, 0, 0, 0, 0, 0, 0, 0, 2, 2, 4, 6, 8, 8, 10, 10 }, /* PORTF */ | |
| { 0, 0, 0, 0, 0, 2, 2, 4, 4, 6, 8, 10, 10, 10, 12, 12 }, /* PORTG */ | |
| { 0, 0, 0, 0, 0, 0, 0, 0, 2, 4, 4, 4, 4, 4, 4, 4 }, /* PORTH */ | |
| # elif defined(CONFIG_BF51x) | |
| { 0, 2, 2, 2, 2, 2, 2, 4, 6, 6, 6, 8, 8, 8, 8, 10 }, /* PORTF */ | |
| { 0, 0, 0, 2, 4, 6, 6, 6, 8, 10, 10, 12, 14, 14, 14, 14 }, /* PORTG */ | |
| { 0, 0, 0, 0, 2, 2, 4, 6, 10, 10, 10, 10, 10, 10, 10, 10 }, /* PORTH */ | |
| # endif | |
| }; | |
| # endif | |
| #elif defined(BF538_FAMILY) | |
| static unsigned short * const port_fer[] = { | |
| (unsigned short *) PORTCIO_FER, | |
| (unsigned short *) PORTDIO_FER, | |
| (unsigned short *) PORTEIO_FER, | |
| }; | |
| #endif | |
| #define RESOURCE_LABEL_SIZE 16 | |
| static struct str_ident { | |
| char name[RESOURCE_LABEL_SIZE]; | |
| } str_ident[MAX_RESOURCES]; | |
| #if defined(CONFIG_PM) | |
| static struct gpio_port_s gpio_bank_saved[GPIO_BANK_NUM]; | |
| # ifdef BF538_FAMILY | |
| static unsigned short port_fer_saved[3]; | |
| # endif | |
| #endif | |
| static void gpio_error(unsigned gpio) | |
| { | |
| printk(KERN_ERR "bfin-gpio: GPIO %d wasn't requested!\n", gpio); | |
| } | |
| static void set_label(unsigned short ident, const char *label) | |
| { | |
| if (label) { | |
| strncpy(str_ident[ident].name, label, | |
| RESOURCE_LABEL_SIZE); | |
| str_ident[ident].name[RESOURCE_LABEL_SIZE - 1] = 0; | |
| } | |
| } | |
| static char *get_label(unsigned short ident) | |
| { | |
| return (*str_ident[ident].name ? str_ident[ident].name : "UNKNOWN"); | |
| } | |
| static int cmp_label(unsigned short ident, const char *label) | |
| { | |
| if (label == NULL) { | |
| dump_stack(); | |
| printk(KERN_ERR "Please provide none-null label\n"); | |
| } | |
| if (label) | |
| return strcmp(str_ident[ident].name, label); | |
| else | |
| return -EINVAL; | |
| } | |
| #define map_entry(m, i) reserved_##m##_map[gpio_bank(i)] | |
| #define is_reserved(m, i, e) (map_entry(m, i) & gpio_bit(i)) | |
| #define reserve(m, i) (map_entry(m, i) |= gpio_bit(i)) | |
| #define unreserve(m, i) (map_entry(m, i) &= ~gpio_bit(i)) | |
| #define DECLARE_RESERVED_MAP(m, c) static unsigned short reserved_##m##_map[c] | |
| DECLARE_RESERVED_MAP(gpio, GPIO_BANK_NUM); | |
| DECLARE_RESERVED_MAP(peri, DIV_ROUND_UP(MAX_RESOURCES, GPIO_BANKSIZE)); | |
| DECLARE_RESERVED_MAP(gpio_irq, GPIO_BANK_NUM); | |
| inline int check_gpio(unsigned gpio) | |
| { | |
| if (gpio >= MAX_BLACKFIN_GPIOS) | |
| return -EINVAL; | |
| return 0; | |
| } | |
| static void port_setup(unsigned gpio, unsigned short usage) | |
| { | |
| #if defined(BF538_FAMILY) | |
| /* | |
| * BF538/9 Port C,D and E are special. | |
| * Inverted PORT_FER polarity on CDE and no PORF_FER on F | |
| * Regular PORT F GPIOs are handled here, CDE are exclusively | |
| * managed by GPIOLIB | |
| */ | |
| if (gpio < MAX_BLACKFIN_GPIOS || gpio >= MAX_RESOURCES) | |
| return; | |
| gpio -= MAX_BLACKFIN_GPIOS; | |
| if (usage == GPIO_USAGE) | |
| *port_fer[gpio_bank(gpio)] |= gpio_bit(gpio); | |
| else | |
| *port_fer[gpio_bank(gpio)] &= ~gpio_bit(gpio); | |
| SSYNC(); | |
| return; | |
| #endif | |
| if (check_gpio(gpio)) | |
| return; | |
| #if defined(CONFIG_BF52x) || defined(BF537_FAMILY) || defined(CONFIG_BF51x) | |
| if (usage == GPIO_USAGE) | |
| *port_fer[gpio_bank(gpio)] &= ~gpio_bit(gpio); | |
| else | |
| *port_fer[gpio_bank(gpio)] |= gpio_bit(gpio); | |
| SSYNC(); | |
| #endif | |
| } | |
| #ifdef BF537_FAMILY | |
| static const s8 port_mux[] = { | |
| [GPIO_PF0] = 3, | |
| [GPIO_PF1] = 3, | |
| [GPIO_PF2] = 4, | |
| [GPIO_PF3] = 4, | |
| [GPIO_PF4] = 5, | |
| [GPIO_PF5] = 6, | |
| [GPIO_PF6] = 7, | |
| [GPIO_PF7] = 8, | |
| [GPIO_PF8 ... GPIO_PF15] = -1, | |
| [GPIO_PG0 ... GPIO_PG7] = -1, | |
| [GPIO_PG8] = 9, | |
| [GPIO_PG9] = 9, | |
| [GPIO_PG10] = 10, | |
| [GPIO_PG11] = 10, | |
| [GPIO_PG12] = 10, | |
| [GPIO_PG13] = 11, | |
| [GPIO_PG14] = 11, | |
| [GPIO_PG15] = 11, | |
| [GPIO_PH0 ... GPIO_PH15] = -1, | |
| [PORT_PJ0 ... PORT_PJ3] = -1, | |
| [PORT_PJ4] = 1, | |
| [PORT_PJ5] = 1, | |
| [PORT_PJ6 ... PORT_PJ9] = -1, | |
| [PORT_PJ10] = 0, | |
| [PORT_PJ11] = 0, | |
| }; | |
| static int portmux_group_check(unsigned short per) | |
| { | |
| u16 ident = P_IDENT(per); | |
| u16 function = P_FUNCT2MUX(per); | |
| s8 offset = port_mux[ident]; | |
| u16 m, pmux, pfunc, mask; | |
| if (offset < 0) | |
| return 0; | |
| pmux = bfin_read_PORT_MUX(); | |
| for (m = 0; m < ARRAY_SIZE(port_mux); ++m) { | |
| if (m == ident) | |
| continue; | |
| if (port_mux[m] != offset) | |
| continue; | |
| if (!is_reserved(peri, m, 1)) | |
| continue; | |
| if (offset == 1) | |
| mask = 3; | |
| else | |
| mask = 1; | |
| pfunc = (pmux >> offset) & mask; | |
| if (pfunc != (function & mask)) { | |
| pr_err("pin group conflict! request pin %d func %d conflict with pin %d func %d\n", | |
| ident, function, m, pfunc); | |
| return -EINVAL; | |
| } | |
| } | |
| return 0; | |
| } | |
| static void portmux_setup(unsigned short per) | |
| { | |
| u16 ident = P_IDENT(per); | |
| u16 function = P_FUNCT2MUX(per); | |
| s8 offset = port_mux[ident]; | |
| u16 pmux, mask; | |
| if (offset == -1) | |
| return; | |
| pmux = bfin_read_PORT_MUX(); | |
| if (offset == 1) | |
| mask = 3; | |
| else | |
| mask = 1; | |
| pmux &= ~(mask << offset); | |
| pmux |= ((function & mask) << offset); | |
| bfin_write_PORT_MUX(pmux); | |
| } | |
| #elif defined(CONFIG_BF52x) || defined(CONFIG_BF51x) | |
| static int portmux_group_check(unsigned short per) | |
| { | |
| u16 ident = P_IDENT(per); | |
| u16 function = P_FUNCT2MUX(per); | |
| u8 offset = pmux_offset[gpio_bank(ident)][gpio_sub_n(ident)]; | |
| u16 pin, gpiopin, pfunc; | |
| for (pin = 0; pin < GPIO_BANKSIZE; ++pin) { | |
| if (offset != pmux_offset[gpio_bank(ident)][pin]) | |
| continue; | |
| gpiopin = gpio_bank(ident) * GPIO_BANKSIZE + pin; | |
| if (gpiopin == ident) | |
| continue; | |
| if (!is_reserved(peri, gpiopin, 1)) | |
| continue; | |
| pfunc = *port_mux[gpio_bank(ident)]; | |
| pfunc = (pfunc >> offset) & 3; | |
| if (pfunc != function) { | |
| pr_err("pin group conflict! request pin %d func %d conflict with pin %d func %d\n", | |
| ident, function, gpiopin, pfunc); | |
| return -EINVAL; | |
| } | |
| } | |
| return 0; | |
| } | |
| inline void portmux_setup(unsigned short per) | |
| { | |
| u16 ident = P_IDENT(per); | |
| u16 function = P_FUNCT2MUX(per); | |
| u8 offset = pmux_offset[gpio_bank(ident)][gpio_sub_n(ident)]; | |
| u16 pmux; | |
| pmux = *port_mux[gpio_bank(ident)]; | |
| if (((pmux >> offset) & 3) == function) | |
| return; | |
| pmux &= ~(3 << offset); | |
| pmux |= (function & 3) << offset; | |
| *port_mux[gpio_bank(ident)] = pmux; | |
| SSYNC(); | |
| } | |
| #else | |
| # define portmux_setup(...) do { } while (0) | |
| static int portmux_group_check(unsigned short per) | |
| { | |
| return 0; | |
| } | |
| #endif | |
| /*********************************************************** | |
| * | |
| * FUNCTIONS: Blackfin General Purpose Ports Access Functions | |
| * | |
| * INPUTS/OUTPUTS: | |
| * gpio - GPIO Number between 0 and MAX_BLACKFIN_GPIOS | |
| * | |
| * | |
| * DESCRIPTION: These functions abstract direct register access | |
| * to Blackfin processor General Purpose | |
| * Ports Regsiters | |
| * | |
| * CAUTION: These functions do not belong to the GPIO Driver API | |
| ************************************************************* | |
| * MODIFICATION HISTORY : | |
| **************************************************************/ | |
| /* Set a specific bit */ | |
| #define SET_GPIO(name) \ | |
| void set_gpio_ ## name(unsigned gpio, unsigned short arg) \ | |
| { \ | |
| unsigned long flags; \ | |
| flags = hard_local_irq_save(); \ | |
| if (arg) \ | |
| gpio_array[gpio_bank(gpio)]->name |= gpio_bit(gpio); \ | |
| else \ | |
| gpio_array[gpio_bank(gpio)]->name &= ~gpio_bit(gpio); \ | |
| AWA_DUMMY_READ(name); \ | |
| hard_local_irq_restore(flags); \ | |
| } \ | |
| EXPORT_SYMBOL(set_gpio_ ## name); | |
| SET_GPIO(dir) /* set_gpio_dir() */ | |
| SET_GPIO(inen) /* set_gpio_inen() */ | |
| SET_GPIO(polar) /* set_gpio_polar() */ | |
| SET_GPIO(edge) /* set_gpio_edge() */ | |
| SET_GPIO(both) /* set_gpio_both() */ | |
| #define SET_GPIO_SC(name) \ | |
| void set_gpio_ ## name(unsigned gpio, unsigned short arg) \ | |
| { \ | |
| unsigned long flags; \ | |
| if (ANOMALY_05000311 || ANOMALY_05000323) \ | |
| flags = hard_local_irq_save(); \ | |
| if (arg) \ | |
| gpio_array[gpio_bank(gpio)]->name ## _set = gpio_bit(gpio); \ | |
| else \ | |
| gpio_array[gpio_bank(gpio)]->name ## _clear = gpio_bit(gpio); \ | |
| if (ANOMALY_05000311 || ANOMALY_05000323) { \ | |
| AWA_DUMMY_READ(name); \ | |
| hard_local_irq_restore(flags); \ | |
| } \ | |
| } \ | |
| EXPORT_SYMBOL(set_gpio_ ## name); | |
| SET_GPIO_SC(maska) | |
| SET_GPIO_SC(maskb) | |
| SET_GPIO_SC(data) | |
| void set_gpio_toggle(unsigned gpio) | |
| { | |
| unsigned long flags; | |
| if (ANOMALY_05000311 || ANOMALY_05000323) | |
| flags = hard_local_irq_save(); | |
| gpio_array[gpio_bank(gpio)]->toggle = gpio_bit(gpio); | |
| if (ANOMALY_05000311 || ANOMALY_05000323) { | |
| AWA_DUMMY_READ(toggle); | |
| hard_local_irq_restore(flags); | |
| } | |
| } | |
| EXPORT_SYMBOL(set_gpio_toggle); | |
| /*Set current PORT date (16-bit word)*/ | |
| #define SET_GPIO_P(name) \ | |
| void set_gpiop_ ## name(unsigned gpio, unsigned short arg) \ | |
| { \ | |
| unsigned long flags; \ | |
| if (ANOMALY_05000311 || ANOMALY_05000323) \ | |
| flags = hard_local_irq_save(); \ | |
| gpio_array[gpio_bank(gpio)]->name = arg; \ | |
| if (ANOMALY_05000311 || ANOMALY_05000323) { \ | |
| AWA_DUMMY_READ(name); \ | |
| hard_local_irq_restore(flags); \ | |
| } \ | |
| } \ | |
| EXPORT_SYMBOL(set_gpiop_ ## name); | |
| SET_GPIO_P(data) | |
| SET_GPIO_P(dir) | |
| SET_GPIO_P(inen) | |
| SET_GPIO_P(polar) | |
| SET_GPIO_P(edge) | |
| SET_GPIO_P(both) | |
| SET_GPIO_P(maska) | |
| SET_GPIO_P(maskb) | |
| /* Get a specific bit */ | |
| #define GET_GPIO(name) \ | |
| unsigned short get_gpio_ ## name(unsigned gpio) \ | |
| { \ | |
| unsigned long flags; \ | |
| unsigned short ret; \ | |
| if (ANOMALY_05000311 || ANOMALY_05000323) \ | |
| flags = hard_local_irq_save(); \ | |
| ret = 0x01 & (gpio_array[gpio_bank(gpio)]->name >> gpio_sub_n(gpio)); \ | |
| if (ANOMALY_05000311 || ANOMALY_05000323) { \ | |
| AWA_DUMMY_READ(name); \ | |
| hard_local_irq_restore(flags); \ | |
| } \ | |
| return ret; \ | |
| } \ | |
| EXPORT_SYMBOL(get_gpio_ ## name); | |
| GET_GPIO(data) | |
| GET_GPIO(dir) | |
| GET_GPIO(inen) | |
| GET_GPIO(polar) | |
| GET_GPIO(edge) | |
| GET_GPIO(both) | |
| GET_GPIO(maska) | |
| GET_GPIO(maskb) | |
| /*Get current PORT date (16-bit word)*/ | |
| #define GET_GPIO_P(name) \ | |
| unsigned short get_gpiop_ ## name(unsigned gpio) \ | |
| { \ | |
| unsigned long flags; \ | |
| unsigned short ret; \ | |
| if (ANOMALY_05000311 || ANOMALY_05000323) \ | |
| flags = hard_local_irq_save(); \ | |
| ret = (gpio_array[gpio_bank(gpio)]->name); \ | |
| if (ANOMALY_05000311 || ANOMALY_05000323) { \ | |
| AWA_DUMMY_READ(name); \ | |
| hard_local_irq_restore(flags); \ | |
| } \ | |
| return ret; \ | |
| } \ | |
| EXPORT_SYMBOL(get_gpiop_ ## name); | |
| GET_GPIO_P(data) | |
| GET_GPIO_P(dir) | |
| GET_GPIO_P(inen) | |
| GET_GPIO_P(polar) | |
| GET_GPIO_P(edge) | |
| GET_GPIO_P(both) | |
| GET_GPIO_P(maska) | |
| GET_GPIO_P(maskb) | |
| #ifdef CONFIG_PM | |
| DECLARE_RESERVED_MAP(wakeup, GPIO_BANK_NUM); | |
| static const unsigned int sic_iwr_irqs[] = { | |
| #if defined(BF533_FAMILY) | |
| IRQ_PROG_INTB | |
| #elif defined(BF537_FAMILY) | |
| IRQ_PF_INTB_WATCH, IRQ_PORTG_INTB, IRQ_PH_INTB_MAC_TX | |
| #elif defined(BF538_FAMILY) | |
| IRQ_PORTF_INTB | |
| #elif defined(CONFIG_BF52x) || defined(CONFIG_BF51x) | |
| IRQ_PORTF_INTB, IRQ_PORTG_INTB, IRQ_PORTH_INTB | |
| #elif defined(BF561_FAMILY) | |
| IRQ_PROG0_INTB, IRQ_PROG1_INTB, IRQ_PROG2_INTB | |
| #else | |
| # error no SIC_IWR defined | |
| #endif | |
| }; | |
| /*********************************************************** | |
| * | |
| * FUNCTIONS: Blackfin PM Setup API | |
| * | |
| * INPUTS/OUTPUTS: | |
| * gpio - GPIO Number between 0 and MAX_BLACKFIN_GPIOS | |
| * type - | |
| * PM_WAKE_RISING | |
| * PM_WAKE_FALLING | |
| * PM_WAKE_HIGH | |
| * PM_WAKE_LOW | |
| * PM_WAKE_BOTH_EDGES | |
| * | |
| * DESCRIPTION: Blackfin PM Driver API | |
| * | |
| * CAUTION: | |
| ************************************************************* | |
| * MODIFICATION HISTORY : | |
| **************************************************************/ | |
| int bfin_gpio_pm_wakeup_ctrl(unsigned gpio, unsigned ctrl) | |
| { | |
| unsigned long flags; | |
| if (check_gpio(gpio) < 0) | |
| return -EINVAL; | |
| flags = hard_local_irq_save(); | |
| if (ctrl) | |
| reserve(wakeup, gpio); | |
| else | |
| unreserve(wakeup, gpio); | |
| set_gpio_maskb(gpio, ctrl); | |
| hard_local_irq_restore(flags); | |
| return 0; | |
| } | |
| int bfin_gpio_pm_standby_ctrl(unsigned ctrl) | |
| { | |
| u16 bank, mask, i; | |
| for (i = 0; i < MAX_BLACKFIN_GPIOS; i += GPIO_BANKSIZE) { | |
| mask = map_entry(wakeup, i); | |
| bank = gpio_bank(i); | |
| if (mask) | |
| bfin_internal_set_wake(sic_iwr_irqs[bank], ctrl); | |
| } | |
| return 0; | |
| } | |
| void bfin_gpio_pm_hibernate_suspend(void) | |
| { | |
| int i, bank; | |
| #ifdef BF538_FAMILY | |
| for (i = 0; i < ARRAY_SIZE(port_fer_saved); ++i) | |
| port_fer_saved[i] = *port_fer[i]; | |
| #endif | |
| for (i = 0; i < MAX_BLACKFIN_GPIOS; i += GPIO_BANKSIZE) { | |
| bank = gpio_bank(i); | |
| #if defined(CONFIG_BF52x) || defined(BF537_FAMILY) || defined(CONFIG_BF51x) | |
| gpio_bank_saved[bank].fer = *port_fer[bank]; | |
| #if defined(CONFIG_BF52x) || defined(CONFIG_BF51x) | |
| gpio_bank_saved[bank].mux = *port_mux[bank]; | |
| #else | |
| if (bank == 0) | |
| gpio_bank_saved[bank].mux = bfin_read_PORT_MUX(); | |
| #endif | |
| #endif | |
| gpio_bank_saved[bank].data = gpio_array[bank]->data; | |
| gpio_bank_saved[bank].inen = gpio_array[bank]->inen; | |
| gpio_bank_saved[bank].polar = gpio_array[bank]->polar; | |
| gpio_bank_saved[bank].dir = gpio_array[bank]->dir; | |
| gpio_bank_saved[bank].edge = gpio_array[bank]->edge; | |
| gpio_bank_saved[bank].both = gpio_array[bank]->both; | |
| gpio_bank_saved[bank].maska = gpio_array[bank]->maska; | |
| } | |
| #ifdef BFIN_SPECIAL_GPIO_BANKS | |
| bfin_special_gpio_pm_hibernate_suspend(); | |
| #endif | |
| AWA_DUMMY_READ(maska); | |
| } | |
| void bfin_gpio_pm_hibernate_restore(void) | |
| { | |
| int i, bank; | |
| #ifdef BF538_FAMILY | |
| for (i = 0; i < ARRAY_SIZE(port_fer_saved); ++i) | |
| *port_fer[i] = port_fer_saved[i]; | |
| #endif | |
| for (i = 0; i < MAX_BLACKFIN_GPIOS; i += GPIO_BANKSIZE) { | |
| bank = gpio_bank(i); | |
| #if defined(CONFIG_BF52x) || defined(BF537_FAMILY) || defined(CONFIG_BF51x) | |
| #if defined(CONFIG_BF52x) || defined(CONFIG_BF51x) | |
| *port_mux[bank] = gpio_bank_saved[bank].mux; | |
| #else | |
| if (bank == 0) | |
| bfin_write_PORT_MUX(gpio_bank_saved[bank].mux); | |
| #endif | |
| *port_fer[bank] = gpio_bank_saved[bank].fer; | |
| #endif | |
| gpio_array[bank]->inen = gpio_bank_saved[bank].inen; | |
| gpio_array[bank]->data_set = gpio_bank_saved[bank].data | |
| & gpio_bank_saved[bank].dir; | |
| gpio_array[bank]->dir = gpio_bank_saved[bank].dir; | |
| gpio_array[bank]->polar = gpio_bank_saved[bank].polar; | |
| gpio_array[bank]->edge = gpio_bank_saved[bank].edge; | |
| gpio_array[bank]->both = gpio_bank_saved[bank].both; | |
| gpio_array[bank]->maska = gpio_bank_saved[bank].maska; | |
| } | |
| #ifdef BFIN_SPECIAL_GPIO_BANKS | |
| bfin_special_gpio_pm_hibernate_restore(); | |
| #endif | |
| AWA_DUMMY_READ(maska); | |
| } | |
| #endif | |
| /*********************************************************** | |
| * | |
| * FUNCTIONS: Blackfin Peripheral Resource Allocation | |
| * and PortMux Setup | |
| * | |
| * INPUTS/OUTPUTS: | |
| * per Peripheral Identifier | |
| * label String | |
| * | |
| * DESCRIPTION: Blackfin Peripheral Resource Allocation and Setup API | |
| * | |
| * CAUTION: | |
| ************************************************************* | |
| * MODIFICATION HISTORY : | |
| **************************************************************/ | |
| int peripheral_request(unsigned short per, const char *label) | |
| { | |
| unsigned long flags; | |
| unsigned short ident = P_IDENT(per); | |
| /* | |
| * Don't cares are pins with only one dedicated function | |
| */ | |
| if (per & P_DONTCARE) | |
| return 0; | |
| if (!(per & P_DEFINED)) | |
| return -ENODEV; | |
| BUG_ON(ident >= MAX_RESOURCES); | |
| flags = hard_local_irq_save(); | |
| /* If a pin can be muxed as either GPIO or peripheral, make | |
| * sure it is not already a GPIO pin when we request it. | |
| */ | |
| if (unlikely(!check_gpio(ident) && is_reserved(gpio, ident, 1))) { | |
| if (system_state == SYSTEM_BOOTING) | |
| dump_stack(); | |
| printk(KERN_ERR | |
| "%s: Peripheral %d is already reserved as GPIO by %s !\n", | |
| __func__, ident, get_label(ident)); | |
| hard_local_irq_restore(flags); | |
| return -EBUSY; | |
| } | |
| if (unlikely(is_reserved(peri, ident, 1))) { | |
| /* | |
| * Pin functions like AMC address strobes my | |
| * be requested and used by several drivers | |
| */ | |
| if (!(per & P_MAYSHARE)) { | |
| /* | |
| * Allow that the identical pin function can | |
| * be requested from the same driver twice | |
| */ | |
| if (cmp_label(ident, label) == 0) | |
| goto anyway; | |
| if (system_state == SYSTEM_BOOTING) | |
| dump_stack(); | |
| printk(KERN_ERR | |
| "%s: Peripheral %d function %d is already reserved by %s !\n", | |
| __func__, ident, P_FUNCT2MUX(per), get_label(ident)); | |
| hard_local_irq_restore(flags); | |
| return -EBUSY; | |
| } | |
| } | |
| if (unlikely(portmux_group_check(per))) { | |
| hard_local_irq_restore(flags); | |
| return -EBUSY; | |
| } | |
| anyway: | |
| reserve(peri, ident); | |
| portmux_setup(per); | |
| port_setup(ident, PERIPHERAL_USAGE); | |
| hard_local_irq_restore(flags); | |
| set_label(ident, label); | |
| return 0; | |
| } | |
| EXPORT_SYMBOL(peripheral_request); | |
| int peripheral_request_list(const unsigned short per[], const char *label) | |
| { | |
| u16 cnt; | |
| int ret; | |
| for (cnt = 0; per[cnt] != 0; cnt++) { | |
| ret = peripheral_request(per[cnt], label); | |
| if (ret < 0) { | |
| for ( ; cnt > 0; cnt--) | |
| peripheral_free(per[cnt - 1]); | |
| return ret; | |
| } | |
| } | |
| return 0; | |
| } | |
| EXPORT_SYMBOL(peripheral_request_list); | |
| void peripheral_free(unsigned short per) | |
| { | |
| unsigned long flags; | |
| unsigned short ident = P_IDENT(per); | |
| if (per & P_DONTCARE) | |
| return; | |
| if (!(per & P_DEFINED)) | |
| return; | |
| flags = hard_local_irq_save(); | |
| if (unlikely(!is_reserved(peri, ident, 0))) { | |
| hard_local_irq_restore(flags); | |
| return; | |
| } | |
| if (!(per & P_MAYSHARE)) | |
| port_setup(ident, GPIO_USAGE); | |
| unreserve(peri, ident); | |
| set_label(ident, "free"); | |
| hard_local_irq_restore(flags); | |
| } | |
| EXPORT_SYMBOL(peripheral_free); | |
| void peripheral_free_list(const unsigned short per[]) | |
| { | |
| u16 cnt; | |
| for (cnt = 0; per[cnt] != 0; cnt++) | |
| peripheral_free(per[cnt]); | |
| } | |
| EXPORT_SYMBOL(peripheral_free_list); | |
| /*********************************************************** | |
| * | |
| * FUNCTIONS: Blackfin GPIO Driver | |
| * | |
| * INPUTS/OUTPUTS: | |
| * gpio PIO Number between 0 and MAX_BLACKFIN_GPIOS | |
| * label String | |
| * | |
| * DESCRIPTION: Blackfin GPIO Driver API | |
| * | |
| * CAUTION: | |
| ************************************************************* | |
| * MODIFICATION HISTORY : | |
| **************************************************************/ | |
| int bfin_gpio_request(unsigned gpio, const char *label) | |
| { | |
| unsigned long flags; | |
| if (check_gpio(gpio) < 0) | |
| return -EINVAL; | |
| flags = hard_local_irq_save(); | |
| /* | |
| * Allow that the identical GPIO can | |
| * be requested from the same driver twice | |
| * Do nothing and return - | |
| */ | |
| if (cmp_label(gpio, label) == 0) { | |
| hard_local_irq_restore(flags); | |
| return 0; | |
| } | |
| if (unlikely(is_reserved(gpio, gpio, 1))) { | |
| if (system_state == SYSTEM_BOOTING) | |
| dump_stack(); | |
| printk(KERN_ERR "bfin-gpio: GPIO %d is already reserved by %s !\n", | |
| gpio, get_label(gpio)); | |
| hard_local_irq_restore(flags); | |
| return -EBUSY; | |
| } | |
| if (unlikely(is_reserved(peri, gpio, 1))) { | |
| if (system_state == SYSTEM_BOOTING) | |
| dump_stack(); | |
| printk(KERN_ERR | |
| "bfin-gpio: GPIO %d is already reserved as Peripheral by %s !\n", | |
| gpio, get_label(gpio)); | |
| hard_local_irq_restore(flags); | |
| return -EBUSY; | |
| } | |
| if (unlikely(is_reserved(gpio_irq, gpio, 1))) { | |
| printk(KERN_NOTICE "bfin-gpio: GPIO %d is already reserved as gpio-irq!" | |
| " (Documentation/blackfin/bfin-gpio-notes.txt)\n", gpio); | |
| } else { /* Reset POLAR setting when acquiring a gpio for the first time */ | |
| set_gpio_polar(gpio, 0); | |
| } | |
| reserve(gpio, gpio); | |
| set_label(gpio, label); | |
| hard_local_irq_restore(flags); | |
| port_setup(gpio, GPIO_USAGE); | |
| return 0; | |
| } | |
| EXPORT_SYMBOL(bfin_gpio_request); | |
| void bfin_gpio_free(unsigned gpio) | |
| { | |
| unsigned long flags; | |
| if (check_gpio(gpio) < 0) | |
| return; | |
| might_sleep(); | |
| flags = hard_local_irq_save(); | |
| if (unlikely(!is_reserved(gpio, gpio, 0))) { | |
| if (system_state == SYSTEM_BOOTING) | |
| dump_stack(); | |
| gpio_error(gpio); | |
| hard_local_irq_restore(flags); | |
| return; | |
| } | |
| unreserve(gpio, gpio); | |
| set_label(gpio, "free"); | |
| hard_local_irq_restore(flags); | |
| } | |
| EXPORT_SYMBOL(bfin_gpio_free); | |
| #ifdef BFIN_SPECIAL_GPIO_BANKS | |
| DECLARE_RESERVED_MAP(special_gpio, gpio_bank(MAX_RESOURCES)); | |
| int bfin_special_gpio_request(unsigned gpio, const char *label) | |
| { | |
| unsigned long flags; | |
| flags = hard_local_irq_save(); | |
| /* | |
| * Allow that the identical GPIO can | |
| * be requested from the same driver twice | |
| * Do nothing and return - | |
| */ | |
| if (cmp_label(gpio, label) == 0) { | |
| hard_local_irq_restore(flags); | |
| return 0; | |
| } | |
| if (unlikely(is_reserved(special_gpio, gpio, 1))) { | |
| hard_local_irq_restore(flags); | |
| printk(KERN_ERR "bfin-gpio: GPIO %d is already reserved by %s !\n", | |
| gpio, get_label(gpio)); | |
| return -EBUSY; | |
| } | |
| if (unlikely(is_reserved(peri, gpio, 1))) { | |
| hard_local_irq_restore(flags); | |
| printk(KERN_ERR | |
| "bfin-gpio: GPIO %d is already reserved as Peripheral by %s !\n", | |
| gpio, get_label(gpio)); | |
| return -EBUSY; | |
| } | |
| reserve(special_gpio, gpio); | |
| reserve(peri, gpio); | |
| set_label(gpio, label); | |
| hard_local_irq_restore(flags); | |
| port_setup(gpio, GPIO_USAGE); | |
| return 0; | |
| } | |
| EXPORT_SYMBOL(bfin_special_gpio_request); | |
| void bfin_special_gpio_free(unsigned gpio) | |
| { | |
| unsigned long flags; | |
| might_sleep(); | |
| flags = hard_local_irq_save(); | |
| if (unlikely(!is_reserved(special_gpio, gpio, 0))) { | |
| gpio_error(gpio); | |
| hard_local_irq_restore(flags); | |
| return; | |
| } | |
| unreserve(special_gpio, gpio); | |
| unreserve(peri, gpio); | |
| set_label(gpio, "free"); | |
| hard_local_irq_restore(flags); | |
| } | |
| EXPORT_SYMBOL(bfin_special_gpio_free); | |
| #endif | |
| int bfin_gpio_irq_request(unsigned gpio, const char *label) | |
| { | |
| unsigned long flags; | |
| if (check_gpio(gpio) < 0) | |
| return -EINVAL; | |
| flags = hard_local_irq_save(); | |
| if (unlikely(is_reserved(peri, gpio, 1))) { | |
| if (system_state == SYSTEM_BOOTING) | |
| dump_stack(); | |
| printk(KERN_ERR | |
| "bfin-gpio: GPIO %d is already reserved as Peripheral by %s !\n", | |
| gpio, get_label(gpio)); | |
| hard_local_irq_restore(flags); | |
| return -EBUSY; | |
| } | |
| if (unlikely(is_reserved(gpio, gpio, 1))) | |
| printk(KERN_NOTICE "bfin-gpio: GPIO %d is already reserved by %s! " | |
| "(Documentation/blackfin/bfin-gpio-notes.txt)\n", | |
| gpio, get_label(gpio)); | |
| reserve(gpio_irq, gpio); | |
| set_label(gpio, label); | |
| hard_local_irq_restore(flags); | |
| port_setup(gpio, GPIO_USAGE); | |
| return 0; | |
| } | |
| void bfin_gpio_irq_free(unsigned gpio) | |
| { | |
| unsigned long flags; | |
| if (check_gpio(gpio) < 0) | |
| return; | |
| flags = hard_local_irq_save(); | |
| if (unlikely(!is_reserved(gpio_irq, gpio, 0))) { | |
| if (system_state == SYSTEM_BOOTING) | |
| dump_stack(); | |
| gpio_error(gpio); | |
| hard_local_irq_restore(flags); | |
| return; | |
| } | |
| unreserve(gpio_irq, gpio); | |
| set_label(gpio, "free"); | |
| hard_local_irq_restore(flags); | |
| } | |
| static inline void __bfin_gpio_direction_input(unsigned gpio) | |
| { | |
| gpio_array[gpio_bank(gpio)]->dir &= ~gpio_bit(gpio); | |
| gpio_array[gpio_bank(gpio)]->inen |= gpio_bit(gpio); | |
| } | |
| int bfin_gpio_direction_input(unsigned gpio) | |
| { | |
| unsigned long flags; | |
| if (unlikely(!is_reserved(gpio, gpio, 0))) { | |
| gpio_error(gpio); | |
| return -EINVAL; | |
| } | |
| flags = hard_local_irq_save(); | |
| __bfin_gpio_direction_input(gpio); | |
| AWA_DUMMY_READ(inen); | |
| hard_local_irq_restore(flags); | |
| return 0; | |
| } | |
| EXPORT_SYMBOL(bfin_gpio_direction_input); | |
| void bfin_gpio_irq_prepare(unsigned gpio) | |
| { | |
| port_setup(gpio, GPIO_USAGE); | |
| } | |
| void bfin_gpio_set_value(unsigned gpio, int arg) | |
| { | |
| if (arg) | |
| gpio_array[gpio_bank(gpio)]->data_set = gpio_bit(gpio); | |
| else | |
| gpio_array[gpio_bank(gpio)]->data_clear = gpio_bit(gpio); | |
| } | |
| EXPORT_SYMBOL(bfin_gpio_set_value); | |
| int bfin_gpio_direction_output(unsigned gpio, int value) | |
| { | |
| unsigned long flags; | |
| if (unlikely(!is_reserved(gpio, gpio, 0))) { | |
| gpio_error(gpio); | |
| return -EINVAL; | |
| } | |
| flags = hard_local_irq_save(); | |
| gpio_array[gpio_bank(gpio)]->inen &= ~gpio_bit(gpio); | |
| gpio_set_value(gpio, value); | |
| gpio_array[gpio_bank(gpio)]->dir |= gpio_bit(gpio); | |
| AWA_DUMMY_READ(dir); | |
| hard_local_irq_restore(flags); | |
| return 0; | |
| } | |
| EXPORT_SYMBOL(bfin_gpio_direction_output); | |
| int bfin_gpio_get_value(unsigned gpio) | |
| { | |
| unsigned long flags; | |
| if (unlikely(get_gpio_edge(gpio))) { | |
| int ret; | |
| flags = hard_local_irq_save(); | |
| set_gpio_edge(gpio, 0); | |
| ret = get_gpio_data(gpio); | |
| set_gpio_edge(gpio, 1); | |
| hard_local_irq_restore(flags); | |
| return ret; | |
| } else | |
| return get_gpio_data(gpio); | |
| } | |
| EXPORT_SYMBOL(bfin_gpio_get_value); | |
| /* If we are booting from SPI and our board lacks a strong enough pull up, | |
| * the core can reset and execute the bootrom faster than the resistor can | |
| * pull the signal logically high. To work around this (common) error in | |
| * board design, we explicitly set the pin back to GPIO mode, force /CS | |
| * high, and wait for the electrons to do their thing. | |
| * | |
| * This function only makes sense to be called from reset code, but it | |
| * lives here as we need to force all the GPIO states w/out going through | |
| * BUG() checks and such. | |
| */ | |
| void bfin_reset_boot_spi_cs(unsigned short pin) | |
| { | |
| unsigned short gpio = P_IDENT(pin); | |
| port_setup(gpio, GPIO_USAGE); | |
| gpio_array[gpio_bank(gpio)]->data_set = gpio_bit(gpio); | |
| AWA_DUMMY_READ(data_set); | |
| udelay(1); | |
| } | |
| #if defined(CONFIG_PROC_FS) | |
| static int gpio_proc_show(struct seq_file *m, void *v) | |
| { | |
| int c, irq, gpio; | |
| for (c = 0; c < MAX_RESOURCES; c++) { | |
| irq = is_reserved(gpio_irq, c, 1); | |
| gpio = is_reserved(gpio, c, 1); | |
| if (!check_gpio(c) && (gpio || irq)) | |
| seq_printf(m, "GPIO_%d: \t%s%s \t\tGPIO %s\n", c, | |
| get_label(c), (gpio && irq) ? " *" : "", | |
| get_gpio_dir(c) ? "OUTPUT" : "INPUT"); | |
| else if (is_reserved(peri, c, 1)) | |
| seq_printf(m, "GPIO_%d: \t%s \t\tPeripheral\n", c, get_label(c)); | |
| else | |
| continue; | |
| } | |
| return 0; | |
| } | |
| static int gpio_proc_open(struct inode *inode, struct file *file) | |
| { | |
| return single_open(file, gpio_proc_show, NULL); | |
| } | |
| static const struct file_operations gpio_proc_ops = { | |
| .open = gpio_proc_open, | |
| .read = seq_read, | |
| .llseek = seq_lseek, | |
| .release = single_release, | |
| }; | |
| static __init int gpio_register_proc(void) | |
| { | |
| struct proc_dir_entry *proc_gpio; | |
| proc_gpio = proc_create("gpio", 0, NULL, &gpio_proc_ops); | |
| return proc_gpio == NULL; | |
| } | |
| __initcall(gpio_register_proc); | |
| #endif | |
| #ifdef CONFIG_GPIOLIB | |
| static int bfin_gpiolib_direction_input(struct gpio_chip *chip, unsigned gpio) | |
| { | |
| return bfin_gpio_direction_input(gpio); | |
| } | |
| static int bfin_gpiolib_direction_output(struct gpio_chip *chip, unsigned gpio, int level) | |
| { | |
| return bfin_gpio_direction_output(gpio, level); | |
| } | |
| static int bfin_gpiolib_get_value(struct gpio_chip *chip, unsigned gpio) | |
| { | |
| return bfin_gpio_get_value(gpio); | |
| } | |
| static void bfin_gpiolib_set_value(struct gpio_chip *chip, unsigned gpio, int value) | |
| { | |
| return bfin_gpio_set_value(gpio, value); | |
| } | |
| static int bfin_gpiolib_gpio_request(struct gpio_chip *chip, unsigned gpio) | |
| { | |
| return bfin_gpio_request(gpio, chip->label); | |
| } | |
| static void bfin_gpiolib_gpio_free(struct gpio_chip *chip, unsigned gpio) | |
| { | |
| return bfin_gpio_free(gpio); | |
| } | |
| static int bfin_gpiolib_gpio_to_irq(struct gpio_chip *chip, unsigned gpio) | |
| { | |
| return gpio + GPIO_IRQ_BASE; | |
| } | |
| static struct gpio_chip bfin_chip = { | |
| .label = "BFIN-GPIO", | |
| .direction_input = bfin_gpiolib_direction_input, | |
| .get = bfin_gpiolib_get_value, | |
| .direction_output = bfin_gpiolib_direction_output, | |
| .set = bfin_gpiolib_set_value, | |
| .request = bfin_gpiolib_gpio_request, | |
| .free = bfin_gpiolib_gpio_free, | |
| .to_irq = bfin_gpiolib_gpio_to_irq, | |
| .base = 0, | |
| .ngpio = MAX_BLACKFIN_GPIOS, | |
| }; | |
| static int __init bfin_gpiolib_setup(void) | |
| { | |
| return gpiochip_add(&bfin_chip); | |
| } | |
| arch_initcall(bfin_gpiolib_setup); | |
| #endif |