| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * MediaTek xHCI Host Controller Driver |
| * |
| * Copyright (c) 2015 MediaTek Inc. |
| * Author: |
| * Chunfeng Yun <chunfeng.yun@mediatek.com> |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/iopoll.h> |
| #include <linux/kernel.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/regmap.h> |
| #include <linux/regulator/consumer.h> |
| |
| #include "xhci.h" |
| #include "xhci-mtk.h" |
| |
| /* ip_pw_ctrl0 register */ |
| #define CTRL0_IP_SW_RST BIT(0) |
| |
| /* ip_pw_ctrl1 register */ |
| #define CTRL1_IP_HOST_PDN BIT(0) |
| |
| /* ip_pw_ctrl2 register */ |
| #define CTRL2_IP_DEV_PDN BIT(0) |
| |
| /* ip_pw_sts1 register */ |
| #define STS1_IP_SLEEP_STS BIT(30) |
| #define STS1_U3_MAC_RST BIT(16) |
| #define STS1_XHCI_RST BIT(11) |
| #define STS1_SYS125_RST BIT(10) |
| #define STS1_REF_RST BIT(8) |
| #define STS1_SYSPLL_STABLE BIT(0) |
| |
| /* ip_xhci_cap register */ |
| #define CAP_U3_PORT_NUM(p) ((p) & 0xff) |
| #define CAP_U2_PORT_NUM(p) (((p) >> 8) & 0xff) |
| |
| /* u3_ctrl_p register */ |
| #define CTRL_U3_PORT_HOST_SEL BIT(2) |
| #define CTRL_U3_PORT_PDN BIT(1) |
| #define CTRL_U3_PORT_DIS BIT(0) |
| |
| /* u2_ctrl_p register */ |
| #define CTRL_U2_PORT_HOST_SEL BIT(2) |
| #define CTRL_U2_PORT_PDN BIT(1) |
| #define CTRL_U2_PORT_DIS BIT(0) |
| |
| /* u2_phy_pll register */ |
| #define CTRL_U2_FORCE_PLL_STB BIT(28) |
| |
| /* usb remote wakeup registers in syscon */ |
| /* mt8173 etc */ |
| #define PERI_WK_CTRL1 0x4 |
| #define WC1_IS_C(x) (((x) & 0xf) << 26) /* cycle debounce */ |
| #define WC1_IS_EN BIT(25) |
| #define WC1_IS_P BIT(6) /* polarity for ip sleep */ |
| |
| /* mt2712 etc */ |
| #define PERI_SSUSB_SPM_CTRL 0x0 |
| #define SSC_IP_SLEEP_EN BIT(4) |
| #define SSC_SPM_INT_EN BIT(1) |
| |
| enum ssusb_uwk_vers { |
| SSUSB_UWK_V1 = 1, |
| SSUSB_UWK_V2, |
| }; |
| |
| static int xhci_mtk_host_enable(struct xhci_hcd_mtk *mtk) |
| { |
| struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs; |
| u32 value, check_val; |
| int u3_ports_disabed = 0; |
| int ret; |
| int i; |
| |
| if (!mtk->has_ippc) |
| return 0; |
| |
| /* power on host ip */ |
| value = readl(&ippc->ip_pw_ctr1); |
| value &= ~CTRL1_IP_HOST_PDN; |
| writel(value, &ippc->ip_pw_ctr1); |
| |
| /* power on and enable u3 ports except skipped ones */ |
| for (i = 0; i < mtk->num_u3_ports; i++) { |
| if ((0x1 << i) & mtk->u3p_dis_msk) { |
| u3_ports_disabed++; |
| continue; |
| } |
| |
| value = readl(&ippc->u3_ctrl_p[i]); |
| value &= ~(CTRL_U3_PORT_PDN | CTRL_U3_PORT_DIS); |
| value |= CTRL_U3_PORT_HOST_SEL; |
| writel(value, &ippc->u3_ctrl_p[i]); |
| } |
| |
| /* power on and enable all u2 ports */ |
| for (i = 0; i < mtk->num_u2_ports; i++) { |
| value = readl(&ippc->u2_ctrl_p[i]); |
| value &= ~(CTRL_U2_PORT_PDN | CTRL_U2_PORT_DIS); |
| value |= CTRL_U2_PORT_HOST_SEL; |
| writel(value, &ippc->u2_ctrl_p[i]); |
| } |
| |
| /* |
| * wait for clocks to be stable, and clock domains reset to |
| * be inactive after power on and enable ports |
| */ |
| check_val = STS1_SYSPLL_STABLE | STS1_REF_RST | |
| STS1_SYS125_RST | STS1_XHCI_RST; |
| |
| if (mtk->num_u3_ports > u3_ports_disabed) |
| check_val |= STS1_U3_MAC_RST; |
| |
| ret = readl_poll_timeout(&ippc->ip_pw_sts1, value, |
| (check_val == (value & check_val)), 100, 20000); |
| if (ret) { |
| dev_err(mtk->dev, "clocks are not stable (0x%x)\n", value); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int xhci_mtk_host_disable(struct xhci_hcd_mtk *mtk) |
| { |
| struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs; |
| u32 value; |
| int ret; |
| int i; |
| |
| if (!mtk->has_ippc) |
| return 0; |
| |
| /* power down u3 ports except skipped ones */ |
| for (i = 0; i < mtk->num_u3_ports; i++) { |
| if ((0x1 << i) & mtk->u3p_dis_msk) |
| continue; |
| |
| value = readl(&ippc->u3_ctrl_p[i]); |
| value |= CTRL_U3_PORT_PDN; |
| writel(value, &ippc->u3_ctrl_p[i]); |
| } |
| |
| /* power down all u2 ports */ |
| for (i = 0; i < mtk->num_u2_ports; i++) { |
| value = readl(&ippc->u2_ctrl_p[i]); |
| value |= CTRL_U2_PORT_PDN; |
| writel(value, &ippc->u2_ctrl_p[i]); |
| } |
| |
| /* power down host ip */ |
| value = readl(&ippc->ip_pw_ctr1); |
| value |= CTRL1_IP_HOST_PDN; |
| writel(value, &ippc->ip_pw_ctr1); |
| |
| /* wait for host ip to sleep */ |
| ret = readl_poll_timeout(&ippc->ip_pw_sts1, value, |
| (value & STS1_IP_SLEEP_STS), 100, 100000); |
| if (ret) { |
| dev_err(mtk->dev, "ip sleep failed!!!\n"); |
| return ret; |
| } |
| return 0; |
| } |
| |
| static int xhci_mtk_ssusb_config(struct xhci_hcd_mtk *mtk) |
| { |
| struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs; |
| u32 value; |
| |
| if (!mtk->has_ippc) |
| return 0; |
| |
| /* reset whole ip */ |
| value = readl(&ippc->ip_pw_ctr0); |
| value |= CTRL0_IP_SW_RST; |
| writel(value, &ippc->ip_pw_ctr0); |
| udelay(1); |
| value = readl(&ippc->ip_pw_ctr0); |
| value &= ~CTRL0_IP_SW_RST; |
| writel(value, &ippc->ip_pw_ctr0); |
| |
| /* |
| * device ip is default power-on in fact |
| * power down device ip, otherwise ip-sleep will fail |
| */ |
| value = readl(&ippc->ip_pw_ctr2); |
| value |= CTRL2_IP_DEV_PDN; |
| writel(value, &ippc->ip_pw_ctr2); |
| |
| value = readl(&ippc->ip_xhci_cap); |
| mtk->num_u3_ports = CAP_U3_PORT_NUM(value); |
| mtk->num_u2_ports = CAP_U2_PORT_NUM(value); |
| dev_dbg(mtk->dev, "%s u2p:%d, u3p:%d\n", __func__, |
| mtk->num_u2_ports, mtk->num_u3_ports); |
| |
| return xhci_mtk_host_enable(mtk); |
| } |
| |
| static int xhci_mtk_clks_get(struct xhci_hcd_mtk *mtk) |
| { |
| struct device *dev = mtk->dev; |
| |
| mtk->sys_clk = devm_clk_get(dev, "sys_ck"); |
| if (IS_ERR(mtk->sys_clk)) { |
| dev_err(dev, "fail to get sys_ck\n"); |
| return PTR_ERR(mtk->sys_clk); |
| } |
| |
| mtk->xhci_clk = devm_clk_get_optional(dev, "xhci_ck"); |
| if (IS_ERR(mtk->xhci_clk)) |
| return PTR_ERR(mtk->xhci_clk); |
| |
| mtk->ref_clk = devm_clk_get_optional(dev, "ref_ck"); |
| if (IS_ERR(mtk->ref_clk)) |
| return PTR_ERR(mtk->ref_clk); |
| |
| mtk->mcu_clk = devm_clk_get_optional(dev, "mcu_ck"); |
| if (IS_ERR(mtk->mcu_clk)) |
| return PTR_ERR(mtk->mcu_clk); |
| |
| mtk->dma_clk = devm_clk_get_optional(dev, "dma_ck"); |
| return PTR_ERR_OR_ZERO(mtk->dma_clk); |
| } |
| |
| static int xhci_mtk_clks_enable(struct xhci_hcd_mtk *mtk) |
| { |
| int ret; |
| |
| ret = clk_prepare_enable(mtk->ref_clk); |
| if (ret) { |
| dev_err(mtk->dev, "failed to enable ref_clk\n"); |
| goto ref_clk_err; |
| } |
| |
| ret = clk_prepare_enable(mtk->sys_clk); |
| if (ret) { |
| dev_err(mtk->dev, "failed to enable sys_clk\n"); |
| goto sys_clk_err; |
| } |
| |
| ret = clk_prepare_enable(mtk->xhci_clk); |
| if (ret) { |
| dev_err(mtk->dev, "failed to enable xhci_clk\n"); |
| goto xhci_clk_err; |
| } |
| |
| ret = clk_prepare_enable(mtk->mcu_clk); |
| if (ret) { |
| dev_err(mtk->dev, "failed to enable mcu_clk\n"); |
| goto mcu_clk_err; |
| } |
| |
| ret = clk_prepare_enable(mtk->dma_clk); |
| if (ret) { |
| dev_err(mtk->dev, "failed to enable dma_clk\n"); |
| goto dma_clk_err; |
| } |
| |
| return 0; |
| |
| dma_clk_err: |
| clk_disable_unprepare(mtk->mcu_clk); |
| mcu_clk_err: |
| clk_disable_unprepare(mtk->xhci_clk); |
| xhci_clk_err: |
| clk_disable_unprepare(mtk->sys_clk); |
| sys_clk_err: |
| clk_disable_unprepare(mtk->ref_clk); |
| ref_clk_err: |
| return ret; |
| } |
| |
| static void xhci_mtk_clks_disable(struct xhci_hcd_mtk *mtk) |
| { |
| clk_disable_unprepare(mtk->dma_clk); |
| clk_disable_unprepare(mtk->mcu_clk); |
| clk_disable_unprepare(mtk->xhci_clk); |
| clk_disable_unprepare(mtk->sys_clk); |
| clk_disable_unprepare(mtk->ref_clk); |
| } |
| |
| /* only clocks can be turn off for ip-sleep wakeup mode */ |
| static void usb_wakeup_ip_sleep_set(struct xhci_hcd_mtk *mtk, bool enable) |
| { |
| u32 reg, msk, val; |
| |
| switch (mtk->uwk_vers) { |
| case SSUSB_UWK_V1: |
| reg = mtk->uwk_reg_base + PERI_WK_CTRL1; |
| msk = WC1_IS_EN | WC1_IS_C(0xf) | WC1_IS_P; |
| val = enable ? (WC1_IS_EN | WC1_IS_C(0x8)) : 0; |
| break; |
| case SSUSB_UWK_V2: |
| reg = mtk->uwk_reg_base + PERI_SSUSB_SPM_CTRL; |
| msk = SSC_IP_SLEEP_EN | SSC_SPM_INT_EN; |
| val = enable ? msk : 0; |
| break; |
| default: |
| return; |
| } |
| regmap_update_bits(mtk->uwk, reg, msk, val); |
| } |
| |
| static int usb_wakeup_of_property_parse(struct xhci_hcd_mtk *mtk, |
| struct device_node *dn) |
| { |
| struct of_phandle_args args; |
| int ret; |
| |
| /* Wakeup function is optional */ |
| mtk->uwk_en = of_property_read_bool(dn, "wakeup-source"); |
| if (!mtk->uwk_en) |
| return 0; |
| |
| ret = of_parse_phandle_with_fixed_args(dn, |
| "mediatek,syscon-wakeup", 2, 0, &args); |
| if (ret) |
| return ret; |
| |
| mtk->uwk_reg_base = args.args[0]; |
| mtk->uwk_vers = args.args[1]; |
| mtk->uwk = syscon_node_to_regmap(args.np); |
| of_node_put(args.np); |
| dev_info(mtk->dev, "uwk - reg:0x%x, version:%d\n", |
| mtk->uwk_reg_base, mtk->uwk_vers); |
| |
| return PTR_ERR_OR_ZERO(mtk->uwk); |
| |
| } |
| |
| static void usb_wakeup_set(struct xhci_hcd_mtk *mtk, bool enable) |
| { |
| if (mtk->uwk_en) |
| usb_wakeup_ip_sleep_set(mtk, enable); |
| } |
| |
| static int xhci_mtk_setup(struct usb_hcd *hcd); |
| static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = { |
| .reset = xhci_mtk_setup, |
| }; |
| |
| static struct hc_driver __read_mostly xhci_mtk_hc_driver; |
| |
| static int xhci_mtk_ldos_enable(struct xhci_hcd_mtk *mtk) |
| { |
| int ret; |
| |
| ret = regulator_enable(mtk->vbus); |
| if (ret) { |
| dev_err(mtk->dev, "failed to enable vbus\n"); |
| return ret; |
| } |
| |
| ret = regulator_enable(mtk->vusb33); |
| if (ret) { |
| dev_err(mtk->dev, "failed to enable vusb33\n"); |
| regulator_disable(mtk->vbus); |
| return ret; |
| } |
| return 0; |
| } |
| |
| static void xhci_mtk_ldos_disable(struct xhci_hcd_mtk *mtk) |
| { |
| regulator_disable(mtk->vbus); |
| regulator_disable(mtk->vusb33); |
| } |
| |
| static void xhci_mtk_quirks(struct device *dev, struct xhci_hcd *xhci) |
| { |
| struct usb_hcd *hcd = xhci_to_hcd(xhci); |
| struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd); |
| |
| /* |
| * As of now platform drivers don't provide MSI support so we ensure |
| * here that the generic code does not try to make a pci_dev from our |
| * dev struct in order to setup MSI |
| */ |
| xhci->quirks |= XHCI_PLAT; |
| xhci->quirks |= XHCI_MTK_HOST; |
| /* |
| * MTK host controller gives a spurious successful event after a |
| * short transfer. Ignore it. |
| */ |
| xhci->quirks |= XHCI_SPURIOUS_SUCCESS; |
| if (mtk->lpm_support) |
| xhci->quirks |= XHCI_LPM_SUPPORT; |
| } |
| |
| /* called during probe() after chip reset completes */ |
| static int xhci_mtk_setup(struct usb_hcd *hcd) |
| { |
| struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd); |
| int ret; |
| |
| if (usb_hcd_is_primary_hcd(hcd)) { |
| ret = xhci_mtk_ssusb_config(mtk); |
| if (ret) |
| return ret; |
| } |
| |
| ret = xhci_gen_setup(hcd, xhci_mtk_quirks); |
| if (ret) |
| return ret; |
| |
| if (usb_hcd_is_primary_hcd(hcd)) { |
| ret = xhci_mtk_sch_init(mtk); |
| if (ret) |
| return ret; |
| } |
| |
| return ret; |
| } |
| |
| static int xhci_mtk_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct device_node *node = dev->of_node; |
| struct xhci_hcd_mtk *mtk; |
| const struct hc_driver *driver; |
| struct xhci_hcd *xhci; |
| struct resource *res; |
| struct usb_hcd *hcd; |
| int ret = -ENODEV; |
| int irq; |
| |
| if (usb_disabled()) |
| return -ENODEV; |
| |
| driver = &xhci_mtk_hc_driver; |
| mtk = devm_kzalloc(dev, sizeof(*mtk), GFP_KERNEL); |
| if (!mtk) |
| return -ENOMEM; |
| |
| mtk->dev = dev; |
| mtk->vbus = devm_regulator_get(dev, "vbus"); |
| if (IS_ERR(mtk->vbus)) { |
| dev_err(dev, "fail to get vbus\n"); |
| return PTR_ERR(mtk->vbus); |
| } |
| |
| mtk->vusb33 = devm_regulator_get(dev, "vusb33"); |
| if (IS_ERR(mtk->vusb33)) { |
| dev_err(dev, "fail to get vusb33\n"); |
| return PTR_ERR(mtk->vusb33); |
| } |
| |
| ret = xhci_mtk_clks_get(mtk); |
| if (ret) |
| return ret; |
| |
| mtk->lpm_support = of_property_read_bool(node, "usb3-lpm-capable"); |
| /* optional property, ignore the error if it does not exist */ |
| of_property_read_u32(node, "mediatek,u3p-dis-msk", |
| &mtk->u3p_dis_msk); |
| |
| ret = usb_wakeup_of_property_parse(mtk, node); |
| if (ret) { |
| dev_err(dev, "failed to parse uwk property\n"); |
| return ret; |
| } |
| |
| pm_runtime_enable(dev); |
| pm_runtime_get_sync(dev); |
| device_enable_async_suspend(dev); |
| |
| ret = xhci_mtk_ldos_enable(mtk); |
| if (ret) |
| goto disable_pm; |
| |
| ret = xhci_mtk_clks_enable(mtk); |
| if (ret) |
| goto disable_ldos; |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) { |
| ret = irq; |
| goto disable_clk; |
| } |
| |
| /* Initialize dma_mask and coherent_dma_mask to 32-bits */ |
| ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32)); |
| if (ret) |
| goto disable_clk; |
| |
| hcd = usb_create_hcd(driver, dev, dev_name(dev)); |
| if (!hcd) { |
| ret = -ENOMEM; |
| goto disable_clk; |
| } |
| |
| /* |
| * USB 2.0 roothub is stored in the platform_device. |
| * Swap it with mtk HCD. |
| */ |
| mtk->hcd = platform_get_drvdata(pdev); |
| platform_set_drvdata(pdev, mtk); |
| |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mac"); |
| hcd->regs = devm_ioremap_resource(dev, res); |
| if (IS_ERR(hcd->regs)) { |
| ret = PTR_ERR(hcd->regs); |
| goto put_usb2_hcd; |
| } |
| hcd->rsrc_start = res->start; |
| hcd->rsrc_len = resource_size(res); |
| |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ippc"); |
| if (res) { /* ippc register is optional */ |
| mtk->ippc_regs = devm_ioremap_resource(dev, res); |
| if (IS_ERR(mtk->ippc_regs)) { |
| ret = PTR_ERR(mtk->ippc_regs); |
| goto put_usb2_hcd; |
| } |
| mtk->has_ippc = true; |
| } else { |
| mtk->has_ippc = false; |
| } |
| |
| device_init_wakeup(dev, true); |
| |
| xhci = hcd_to_xhci(hcd); |
| xhci->main_hcd = hcd; |
| |
| /* |
| * imod_interval is the interrupt moderation value in nanoseconds. |
| * The increment interval is 8 times as much as that defined in |
| * the xHCI spec on MTK's controller. |
| */ |
| xhci->imod_interval = 5000; |
| device_property_read_u32(dev, "imod-interval-ns", &xhci->imod_interval); |
| |
| xhci->shared_hcd = usb_create_shared_hcd(driver, dev, |
| dev_name(dev), hcd); |
| if (!xhci->shared_hcd) { |
| ret = -ENOMEM; |
| goto disable_device_wakeup; |
| } |
| |
| ret = usb_add_hcd(hcd, irq, IRQF_SHARED); |
| if (ret) |
| goto put_usb3_hcd; |
| |
| if (HCC_MAX_PSA(xhci->hcc_params) >= 4) |
| xhci->shared_hcd->can_do_streams = 1; |
| |
| ret = usb_add_hcd(xhci->shared_hcd, irq, IRQF_SHARED); |
| if (ret) |
| goto dealloc_usb2_hcd; |
| |
| return 0; |
| |
| dealloc_usb2_hcd: |
| usb_remove_hcd(hcd); |
| |
| put_usb3_hcd: |
| xhci_mtk_sch_exit(mtk); |
| usb_put_hcd(xhci->shared_hcd); |
| |
| disable_device_wakeup: |
| device_init_wakeup(dev, false); |
| |
| put_usb2_hcd: |
| usb_put_hcd(hcd); |
| |
| disable_clk: |
| xhci_mtk_clks_disable(mtk); |
| |
| disable_ldos: |
| xhci_mtk_ldos_disable(mtk); |
| |
| disable_pm: |
| pm_runtime_put_sync(dev); |
| pm_runtime_disable(dev); |
| return ret; |
| } |
| |
| static int xhci_mtk_remove(struct platform_device *dev) |
| { |
| struct xhci_hcd_mtk *mtk = platform_get_drvdata(dev); |
| struct usb_hcd *hcd = mtk->hcd; |
| struct xhci_hcd *xhci = hcd_to_xhci(hcd); |
| struct usb_hcd *shared_hcd = xhci->shared_hcd; |
| |
| usb_remove_hcd(shared_hcd); |
| xhci->shared_hcd = NULL; |
| device_init_wakeup(&dev->dev, false); |
| |
| usb_remove_hcd(hcd); |
| usb_put_hcd(shared_hcd); |
| usb_put_hcd(hcd); |
| xhci_mtk_sch_exit(mtk); |
| xhci_mtk_clks_disable(mtk); |
| xhci_mtk_ldos_disable(mtk); |
| pm_runtime_put_sync(&dev->dev); |
| pm_runtime_disable(&dev->dev); |
| |
| return 0; |
| } |
| |
| /* |
| * if ip sleep fails, and all clocks are disabled, access register will hang |
| * AHB bus, so stop polling roothubs to avoid regs access on bus suspend. |
| * and no need to check whether ip sleep failed or not; this will cause SPM |
| * to wake up system immediately after system suspend complete if ip sleep |
| * fails, it is what we wanted. |
| */ |
| static int __maybe_unused xhci_mtk_suspend(struct device *dev) |
| { |
| struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev); |
| struct usb_hcd *hcd = mtk->hcd; |
| struct xhci_hcd *xhci = hcd_to_xhci(hcd); |
| |
| xhci_dbg(xhci, "%s: stop port polling\n", __func__); |
| clear_bit(HCD_FLAG_POLL_RH, &hcd->flags); |
| del_timer_sync(&hcd->rh_timer); |
| clear_bit(HCD_FLAG_POLL_RH, &xhci->shared_hcd->flags); |
| del_timer_sync(&xhci->shared_hcd->rh_timer); |
| |
| xhci_mtk_host_disable(mtk); |
| xhci_mtk_clks_disable(mtk); |
| usb_wakeup_set(mtk, true); |
| return 0; |
| } |
| |
| static int __maybe_unused xhci_mtk_resume(struct device *dev) |
| { |
| struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev); |
| struct usb_hcd *hcd = mtk->hcd; |
| struct xhci_hcd *xhci = hcd_to_xhci(hcd); |
| |
| usb_wakeup_set(mtk, false); |
| xhci_mtk_clks_enable(mtk); |
| xhci_mtk_host_enable(mtk); |
| |
| xhci_dbg(xhci, "%s: restart port polling\n", __func__); |
| set_bit(HCD_FLAG_POLL_RH, &xhci->shared_hcd->flags); |
| usb_hcd_poll_rh_status(xhci->shared_hcd); |
| set_bit(HCD_FLAG_POLL_RH, &hcd->flags); |
| usb_hcd_poll_rh_status(hcd); |
| return 0; |
| } |
| |
| static const struct dev_pm_ops xhci_mtk_pm_ops = { |
| SET_SYSTEM_SLEEP_PM_OPS(xhci_mtk_suspend, xhci_mtk_resume) |
| }; |
| #define DEV_PM_OPS IS_ENABLED(CONFIG_PM) ? &xhci_mtk_pm_ops : NULL |
| |
| #ifdef CONFIG_OF |
| static const struct of_device_id mtk_xhci_of_match[] = { |
| { .compatible = "mediatek,mt8173-xhci"}, |
| { .compatible = "mediatek,mtk-xhci"}, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, mtk_xhci_of_match); |
| #endif |
| |
| static struct platform_driver mtk_xhci_driver = { |
| .probe = xhci_mtk_probe, |
| .remove = xhci_mtk_remove, |
| .driver = { |
| .name = "xhci-mtk", |
| .pm = DEV_PM_OPS, |
| .of_match_table = of_match_ptr(mtk_xhci_of_match), |
| }, |
| }; |
| MODULE_ALIAS("platform:xhci-mtk"); |
| |
| static int __init xhci_mtk_init(void) |
| { |
| xhci_init_driver(&xhci_mtk_hc_driver, &xhci_mtk_overrides); |
| return platform_driver_register(&mtk_xhci_driver); |
| } |
| module_init(xhci_mtk_init); |
| |
| static void __exit xhci_mtk_exit(void) |
| { |
| platform_driver_unregister(&mtk_xhci_driver); |
| } |
| module_exit(xhci_mtk_exit); |
| |
| MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>"); |
| MODULE_DESCRIPTION("MediaTek xHCI Host Controller Driver"); |
| MODULE_LICENSE("GPL v2"); |