| # | |
| # Phy drivers for Broadcom platforms | |
| # | |
| config PHY_CYGNUS_PCIE | |
| tristate "Broadcom Cygnus PCIe PHY driver" | |
| depends on OF && (ARCH_BCM_CYGNUS || COMPILE_TEST) | |
| select GENERIC_PHY | |
| default ARCH_BCM_CYGNUS | |
| help | |
| Enable this to support the Broadcom Cygnus PCIe PHY. | |
| If unsure, say N. | |
| config BCM_KONA_USB2_PHY | |
| tristate "Broadcom Kona USB2 PHY Driver" | |
| depends on HAS_IOMEM | |
| select GENERIC_PHY | |
| help | |
| Enable this to support the Broadcom Kona USB 2.0 PHY. | |
| config PHY_BCM_NS_USB2 | |
| tristate "Broadcom Northstar USB 2.0 PHY Driver" | |
| depends on ARCH_BCM_IPROC || COMPILE_TEST | |
| depends on HAS_IOMEM && OF | |
| select GENERIC_PHY | |
| help | |
| Enable this to support Broadcom USB 2.0 PHY connected to the USB | |
| controller on Northstar family. | |
| config PHY_BCM_NS_USB3 | |
| tristate "Broadcom Northstar USB 3.0 PHY Driver" | |
| depends on ARCH_BCM_IPROC || COMPILE_TEST | |
| depends on HAS_IOMEM && OF | |
| depends on MDIO_BUS | |
| select GENERIC_PHY | |
| help | |
| Enable this to support Broadcom USB 3.0 PHY connected to the USB | |
| controller on Northstar family. | |
| config PHY_NS2_PCIE | |
| tristate "Broadcom Northstar2 PCIe PHY driver" | |
| depends on OF && MDIO_BUS_MUX_BCM_IPROC | |
| select GENERIC_PHY | |
| default ARCH_BCM_IPROC | |
| help | |
| Enable this to support the Broadcom Northstar2 PCIe PHY. | |
| If unsure, say N. | |
| config PHY_NS2_USB_DRD | |
| tristate "Broadcom Northstar2 USB DRD PHY support" | |
| depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST) | |
| select GENERIC_PHY | |
| select EXTCON | |
| default ARCH_BCM_IPROC | |
| help | |
| Enable this to support the Broadcom Northstar2 USB DRD PHY. | |
| This driver initializes the PHY in either HOST or DEVICE mode. | |
| The host or device configuration is read from device tree. | |
| If unsure, say N. | |
| config PHY_BRCM_SATA | |
| tristate "Broadcom SATA PHY driver" | |
| depends on ARCH_BRCMSTB || ARCH_BCM_IPROC || BMIPS_GENERIC || COMPILE_TEST | |
| depends on OF | |
| select GENERIC_PHY | |
| default ARCH_BCM_IPROC | |
| help | |
| Enable this to support the Broadcom SATA PHY. | |
| If unsure, say N. | |
| config PHY_BRCM_USB | |
| tristate "Broadcom STB USB PHY driver" | |
| depends on ARCH_BRCMSTB | |
| depends on OF | |
| select GENERIC_PHY | |
| select SOC_BRCMSTB | |
| default ARCH_BRCMSTB | |
| help | |
| Enable this to support the Broadcom STB USB PHY. | |
| This driver is required by the USB XHCI, EHCI and OHCI | |
| drivers. | |
| If unsure, say N. |