| /* | |
| * twl4030.h - header for TWL4030 PM and audio CODEC device | |
| * | |
| * Copyright (C) 2005-2006 Texas Instruments, Inc. | |
| * | |
| * Based on tlv320aic23.c: | |
| * Copyright (c) by Kai Svahn <kai.svahn@nokia.com> | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License as published by | |
| * the Free Software Foundation; either version 2 of the License, or | |
| * (at your option) any later version. | |
| * | |
| * This program is distributed in the hope that it will be useful, | |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| * GNU General Public License for more details. | |
| * | |
| * You should have received a copy of the GNU General Public License | |
| * along with this program; if not, write to the Free Software | |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA | |
| * | |
| */ | |
| #ifndef __TWL4030_H_ | |
| #define __TWL4030_H_ | |
| /* | |
| * Using the twl4030 core we address registers using a pair | |
| * { module id, relative register offset } | |
| * which that core then maps to the relevant | |
| * { i2c slave, absolute register address } | |
| * | |
| * The module IDs are meaningful only to the twl4030 core code, | |
| * which uses them as array indices to look up the first register | |
| * address each module uses within a given i2c slave. | |
| */ | |
| /* Slave 0 (i2c address 0x48) */ | |
| #define TWL4030_MODULE_USB 0x00 | |
| /* Slave 1 (i2c address 0x49) */ | |
| #define TWL4030_MODULE_AUDIO_VOICE 0x01 | |
| #define TWL4030_MODULE_GPIO 0x02 | |
| #define TWL4030_MODULE_INTBR 0x03 | |
| #define TWL4030_MODULE_PIH 0x04 | |
| #define TWL4030_MODULE_TEST 0x05 | |
| /* Slave 2 (i2c address 0x4a) */ | |
| #define TWL4030_MODULE_KEYPAD 0x06 | |
| #define TWL4030_MODULE_MADC 0x07 | |
| #define TWL4030_MODULE_INTERRUPTS 0x08 | |
| #define TWL4030_MODULE_LED 0x09 | |
| #define TWL4030_MODULE_MAIN_CHARGE 0x0A | |
| #define TWL4030_MODULE_PRECHARGE 0x0B | |
| #define TWL4030_MODULE_PWM0 0x0C | |
| #define TWL4030_MODULE_PWM1 0x0D | |
| #define TWL4030_MODULE_PWMA 0x0E | |
| #define TWL4030_MODULE_PWMB 0x0F | |
| /* Slave 3 (i2c address 0x4b) */ | |
| #define TWL4030_MODULE_BACKUP 0x10 | |
| #define TWL4030_MODULE_INT 0x11 | |
| #define TWL4030_MODULE_PM_MASTER 0x12 | |
| #define TWL4030_MODULE_PM_RECEIVER 0x13 | |
| #define TWL4030_MODULE_RTC 0x14 | |
| #define TWL4030_MODULE_SECURED_REG 0x15 | |
| /* | |
| * Read and write single 8-bit registers | |
| */ | |
| int twl4030_i2c_write_u8(u8 mod_no, u8 val, u8 reg); | |
| int twl4030_i2c_read_u8(u8 mod_no, u8 *val, u8 reg); | |
| /* | |
| * Read and write several 8-bit registers at once. | |
| * | |
| * IMPORTANT: For twl4030_i2c_write(), allocate num_bytes + 1 | |
| * for the value, and populate your data starting at offset 1. | |
| */ | |
| int twl4030_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes); | |
| int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes); | |
| /*----------------------------------------------------------------------*/ | |
| /* | |
| * NOTE: at up to 1024 registers, this is a big chip. | |
| * | |
| * Avoid putting register declarations in this file, instead of into | |
| * a driver-private file, unless some of the registers in a block | |
| * need to be shared with other drivers. One example is blocks that | |
| * have Secondary IRQ Handler (SIH) registers. | |
| */ | |
| #define TWL4030_SIH_CTRL_EXCLEN_MASK BIT(0) | |
| #define TWL4030_SIH_CTRL_PENDDIS_MASK BIT(1) | |
| #define TWL4030_SIH_CTRL_COR_MASK BIT(2) | |
| /*----------------------------------------------------------------------*/ | |
| /* | |
| * GPIO Block Register offsets (use TWL4030_MODULE_GPIO) | |
| */ | |
| #define REG_GPIODATAIN1 0x0 | |
| #define REG_GPIODATAIN2 0x1 | |
| #define REG_GPIODATAIN3 0x2 | |
| #define REG_GPIODATADIR1 0x3 | |
| #define REG_GPIODATADIR2 0x4 | |
| #define REG_GPIODATADIR3 0x5 | |
| #define REG_GPIODATAOUT1 0x6 | |
| #define REG_GPIODATAOUT2 0x7 | |
| #define REG_GPIODATAOUT3 0x8 | |
| #define REG_CLEARGPIODATAOUT1 0x9 | |
| #define REG_CLEARGPIODATAOUT2 0xA | |
| #define REG_CLEARGPIODATAOUT3 0xB | |
| #define REG_SETGPIODATAOUT1 0xC | |
| #define REG_SETGPIODATAOUT2 0xD | |
| #define REG_SETGPIODATAOUT3 0xE | |
| #define REG_GPIO_DEBEN1 0xF | |
| #define REG_GPIO_DEBEN2 0x10 | |
| #define REG_GPIO_DEBEN3 0x11 | |
| #define REG_GPIO_CTRL 0x12 | |
| #define REG_GPIOPUPDCTR1 0x13 | |
| #define REG_GPIOPUPDCTR2 0x14 | |
| #define REG_GPIOPUPDCTR3 0x15 | |
| #define REG_GPIOPUPDCTR4 0x16 | |
| #define REG_GPIOPUPDCTR5 0x17 | |
| #define REG_GPIO_ISR1A 0x19 | |
| #define REG_GPIO_ISR2A 0x1A | |
| #define REG_GPIO_ISR3A 0x1B | |
| #define REG_GPIO_IMR1A 0x1C | |
| #define REG_GPIO_IMR2A 0x1D | |
| #define REG_GPIO_IMR3A 0x1E | |
| #define REG_GPIO_ISR1B 0x1F | |
| #define REG_GPIO_ISR2B 0x20 | |
| #define REG_GPIO_ISR3B 0x21 | |
| #define REG_GPIO_IMR1B 0x22 | |
| #define REG_GPIO_IMR2B 0x23 | |
| #define REG_GPIO_IMR3B 0x24 | |
| #define REG_GPIO_EDR1 0x28 | |
| #define REG_GPIO_EDR2 0x29 | |
| #define REG_GPIO_EDR3 0x2A | |
| #define REG_GPIO_EDR4 0x2B | |
| #define REG_GPIO_EDR5 0x2C | |
| #define REG_GPIO_SIH_CTRL 0x2D | |
| /* Up to 18 signals are available as GPIOs, when their | |
| * pins are not assigned to another use (such as ULPI/USB). | |
| */ | |
| #define TWL4030_GPIO_MAX 18 | |
| /*----------------------------------------------------------------------*/ | |
| /* | |
| * Keypad register offsets (use TWL4030_MODULE_KEYPAD) | |
| * ... SIH/interrupt only | |
| */ | |
| #define TWL4030_KEYPAD_KEYP_ISR1 0x11 | |
| #define TWL4030_KEYPAD_KEYP_IMR1 0x12 | |
| #define TWL4030_KEYPAD_KEYP_ISR2 0x13 | |
| #define TWL4030_KEYPAD_KEYP_IMR2 0x14 | |
| #define TWL4030_KEYPAD_KEYP_SIR 0x15 /* test register */ | |
| #define TWL4030_KEYPAD_KEYP_EDR 0x16 | |
| #define TWL4030_KEYPAD_KEYP_SIH_CTRL 0x17 | |
| /*----------------------------------------------------------------------*/ | |
| /* | |
| * Multichannel ADC register offsets (use TWL4030_MODULE_MADC) | |
| * ... SIH/interrupt only | |
| */ | |
| #define TWL4030_MADC_ISR1 0x61 | |
| #define TWL4030_MADC_IMR1 0x62 | |
| #define TWL4030_MADC_ISR2 0x63 | |
| #define TWL4030_MADC_IMR2 0x64 | |
| #define TWL4030_MADC_SIR 0x65 /* test register */ | |
| #define TWL4030_MADC_EDR 0x66 | |
| #define TWL4030_MADC_SIH_CTRL 0x67 | |
| /*----------------------------------------------------------------------*/ | |
| /* | |
| * Battery charger register offsets (use TWL4030_MODULE_INTERRUPTS) | |
| */ | |
| #define TWL4030_INTERRUPTS_BCIISR1A 0x0 | |
| #define TWL4030_INTERRUPTS_BCIISR2A 0x1 | |
| #define TWL4030_INTERRUPTS_BCIIMR1A 0x2 | |
| #define TWL4030_INTERRUPTS_BCIIMR2A 0x3 | |
| #define TWL4030_INTERRUPTS_BCIISR1B 0x4 | |
| #define TWL4030_INTERRUPTS_BCIISR2B 0x5 | |
| #define TWL4030_INTERRUPTS_BCIIMR1B 0x6 | |
| #define TWL4030_INTERRUPTS_BCIIMR2B 0x7 | |
| #define TWL4030_INTERRUPTS_BCISIR1 0x8 /* test register */ | |
| #define TWL4030_INTERRUPTS_BCISIR2 0x9 /* test register */ | |
| #define TWL4030_INTERRUPTS_BCIEDR1 0xa | |
| #define TWL4030_INTERRUPTS_BCIEDR2 0xb | |
| #define TWL4030_INTERRUPTS_BCIEDR3 0xc | |
| #define TWL4030_INTERRUPTS_BCISIHCTRL 0xd | |
| /*----------------------------------------------------------------------*/ | |
| /* | |
| * Power Interrupt block register offsets (use TWL4030_MODULE_INT) | |
| */ | |
| #define TWL4030_INT_PWR_ISR1 0x0 | |
| #define TWL4030_INT_PWR_IMR1 0x1 | |
| #define TWL4030_INT_PWR_ISR2 0x2 | |
| #define TWL4030_INT_PWR_IMR2 0x3 | |
| #define TWL4030_INT_PWR_SIR 0x4 /* test register */ | |
| #define TWL4030_INT_PWR_EDR1 0x5 | |
| #define TWL4030_INT_PWR_EDR2 0x6 | |
| #define TWL4030_INT_PWR_SIH_CTRL 0x7 | |
| /*----------------------------------------------------------------------*/ | |
| /* Power bus message definitions */ | |
| #define DEV_GRP_NULL 0x0 | |
| #define DEV_GRP_P1 0x1 | |
| #define DEV_GRP_P2 0x2 | |
| #define DEV_GRP_P3 0x4 | |
| #define RES_GRP_RES 0x0 | |
| #define RES_GRP_PP 0x1 | |
| #define RES_GRP_RC 0x2 | |
| #define RES_GRP_PP_RC 0x3 | |
| #define RES_GRP_PR 0x4 | |
| #define RES_GRP_PP_PR 0x5 | |
| #define RES_GRP_RC_PR 0x6 | |
| #define RES_GRP_ALL 0x7 | |
| #define RES_TYPE2_R0 0x0 | |
| #define RES_TYPE_ALL 0x7 | |
| #define RES_STATE_WRST 0xF | |
| #define RES_STATE_ACTIVE 0xE | |
| #define RES_STATE_SLEEP 0x8 | |
| #define RES_STATE_OFF 0x0 | |
| /* | |
| * Power Bus Message Format ... these can be sent individually by Linux, | |
| * but are usually part of downloaded scripts that are run when various | |
| * power events are triggered. | |
| * | |
| * Broadcast Message (16 Bits): | |
| * DEV_GRP[15:13] MT[12] RES_GRP[11:9] RES_TYPE2[8:7] RES_TYPE[6:4] | |
| * RES_STATE[3:0] | |
| * | |
| * Singular Message (16 Bits): | |
| * DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0] | |
| */ | |
| #define MSG_BROADCAST(devgrp, grp, type, type2, state) \ | |
| ( (devgrp) << 13 | 1 << 12 | (grp) << 9 | (type2) << 7 \ | |
| | (type) << 4 | (state)) | |
| #define MSG_SINGULAR(devgrp, id, state) \ | |
| ((devgrp) << 13 | 0 << 12 | (id) << 4 | (state)) | |
| /*----------------------------------------------------------------------*/ | |
| struct twl4030_bci_platform_data { | |
| int *battery_tmp_tbl; | |
| unsigned int tblsize; | |
| }; | |
| /* TWL4030_GPIO_MAX (18) GPIOs, with interrupts */ | |
| struct twl4030_gpio_platform_data { | |
| int gpio_base; | |
| unsigned irq_base, irq_end; | |
| /* package the two LED signals as output-only GPIOs? */ | |
| bool use_leds; | |
| /* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */ | |
| u8 mmc_cd; | |
| /* if BIT(N) is set, or VMMC(n+1) is linked, debounce GPIO-N */ | |
| u32 debounce; | |
| /* For gpio-N, bit (1 << N) in "pullups" is set if that pullup | |
| * should be enabled. Else, if that bit is set in "pulldowns", | |
| * that pulldown is enabled. Don't waste power by letting any | |
| * digital inputs float... | |
| */ | |
| u32 pullups; | |
| u32 pulldowns; | |
| int (*setup)(struct device *dev, | |
| unsigned gpio, unsigned ngpio); | |
| int (*teardown)(struct device *dev, | |
| unsigned gpio, unsigned ngpio); | |
| }; | |
| struct twl4030_madc_platform_data { | |
| int irq_line; | |
| }; | |
| struct twl4030_keypad_data { | |
| int rows; | |
| int cols; | |
| int *keymap; | |
| int irq; | |
| unsigned int keymapsize; | |
| unsigned int rep:1; | |
| }; | |
| enum twl4030_usb_mode { | |
| T2_USB_MODE_ULPI = 1, | |
| T2_USB_MODE_CEA2011_3PIN = 2, | |
| }; | |
| struct twl4030_usb_data { | |
| enum twl4030_usb_mode usb_mode; | |
| }; | |
| struct twl4030_platform_data { | |
| unsigned irq_base, irq_end; | |
| struct twl4030_bci_platform_data *bci; | |
| struct twl4030_gpio_platform_data *gpio; | |
| struct twl4030_madc_platform_data *madc; | |
| struct twl4030_keypad_data *keypad; | |
| struct twl4030_usb_data *usb; | |
| /* LDO regulators */ | |
| struct regulator_init_data *vdac; | |
| struct regulator_init_data *vpll1; | |
| struct regulator_init_data *vpll2; | |
| struct regulator_init_data *vmmc1; | |
| struct regulator_init_data *vmmc2; | |
| struct regulator_init_data *vsim; | |
| struct regulator_init_data *vaux1; | |
| struct regulator_init_data *vaux2; | |
| struct regulator_init_data *vaux3; | |
| struct regulator_init_data *vaux4; | |
| /* REVISIT more to come ... _nothing_ should be hard-wired */ | |
| }; | |
| /*----------------------------------------------------------------------*/ | |
| int twl4030_sih_setup(int module); | |
| /* Offsets to Power Registers */ | |
| #define TWL4030_VDAC_DEV_GRP 0x3B | |
| #define TWL4030_VDAC_DEDICATED 0x3E | |
| #define TWL4030_VAUX1_DEV_GRP 0x17 | |
| #define TWL4030_VAUX1_DEDICATED 0x1A | |
| #define TWL4030_VAUX2_DEV_GRP 0x1B | |
| #define TWL4030_VAUX2_DEDICATED 0x1E | |
| #define TWL4030_VAUX3_DEV_GRP 0x1F | |
| #define TWL4030_VAUX3_DEDICATED 0x22 | |
| #if defined(CONFIG_TWL4030_BCI_BATTERY) || \ | |
| defined(CONFIG_TWL4030_BCI_BATTERY_MODULE) | |
| extern int twl4030charger_usb_en(int enable); | |
| #else | |
| static inline int twl4030charger_usb_en(int enable) { return 0; } | |
| #endif | |
| /*----------------------------------------------------------------------*/ | |
| /* Linux-specific regulator identifiers ... for now, we only support | |
| * the LDOs, and leave the three buck converters alone. VDD1 and VDD2 | |
| * need to tie into hardware based voltage scaling (cpufreq etc), while | |
| * VIO is generally fixed. | |
| */ | |
| /* EXTERNAL dc-to-dc buck converters */ | |
| #define TWL4030_REG_VDD1 0 | |
| #define TWL4030_REG_VDD2 1 | |
| #define TWL4030_REG_VIO 2 | |
| /* EXTERNAL LDOs */ | |
| #define TWL4030_REG_VDAC 3 | |
| #define TWL4030_REG_VPLL1 4 | |
| #define TWL4030_REG_VPLL2 5 /* not on all chips */ | |
| #define TWL4030_REG_VMMC1 6 | |
| #define TWL4030_REG_VMMC2 7 /* not on all chips */ | |
| #define TWL4030_REG_VSIM 8 /* not on all chips */ | |
| #define TWL4030_REG_VAUX1 9 /* not on all chips */ | |
| #define TWL4030_REG_VAUX2_4030 10 /* (twl4030-specific) */ | |
| #define TWL4030_REG_VAUX2 11 /* (twl5030 and newer) */ | |
| #define TWL4030_REG_VAUX3 12 /* not on all chips */ | |
| #define TWL4030_REG_VAUX4 13 /* not on all chips */ | |
| /* INTERNAL LDOs */ | |
| #define TWL4030_REG_VINTANA1 14 | |
| #define TWL4030_REG_VINTANA2 15 | |
| #define TWL4030_REG_VINTDIG 16 | |
| #define TWL4030_REG_VUSB1V5 17 | |
| #define TWL4030_REG_VUSB1V8 18 | |
| #define TWL4030_REG_VUSB3V1 19 | |
| #endif /* End of __TWL4030_H */ |