| /* |
| * Analogix DP (Display port) core register interface driver. |
| * |
| * Copyright (C) 2012 Samsung Electronics Co., Ltd. |
| * Author: Jingoo Han <jg1.han@samsung.com> |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/device.h> |
| #include <linux/gpio.h> |
| #include <linux/io.h> |
| #include <linux/iopoll.h> |
| |
| #include <drm/bridge/analogix_dp.h> |
| |
| #include "analogix_dp_core.h" |
| #include "analogix_dp_reg.h" |
| |
| #define COMMON_INT_MASK_1 0 |
| #define COMMON_INT_MASK_2 0 |
| #define COMMON_INT_MASK_3 0 |
| #define COMMON_INT_MASK_4 (HOTPLUG_CHG | HPD_LOST | PLUG) |
| #define INT_STA_MASK INT_HPD |
| |
| void analogix_dp_enable_video_mute(struct analogix_dp_device *dp, bool enable) |
| { |
| u32 reg; |
| |
| if (enable) { |
| reg = readl(dp->reg_base + ANALOGIX_DP_VIDEO_CTL_1); |
| reg |= HDCP_VIDEO_MUTE; |
| writel(reg, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_1); |
| } else { |
| reg = readl(dp->reg_base + ANALOGIX_DP_VIDEO_CTL_1); |
| reg &= ~HDCP_VIDEO_MUTE; |
| writel(reg, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_1); |
| } |
| } |
| |
| void analogix_dp_stop_video(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_VIDEO_CTL_1); |
| reg &= ~VIDEO_EN; |
| writel(reg, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_1); |
| } |
| |
| void analogix_dp_lane_swap(struct analogix_dp_device *dp, bool enable) |
| { |
| u32 reg; |
| |
| if (enable) |
| reg = LANE3_MAP_LOGIC_LANE_0 | LANE2_MAP_LOGIC_LANE_1 | |
| LANE1_MAP_LOGIC_LANE_2 | LANE0_MAP_LOGIC_LANE_3; |
| else |
| reg = LANE3_MAP_LOGIC_LANE_3 | LANE2_MAP_LOGIC_LANE_2 | |
| LANE1_MAP_LOGIC_LANE_1 | LANE0_MAP_LOGIC_LANE_0; |
| |
| writel(reg, dp->reg_base + ANALOGIX_DP_LANE_MAP); |
| } |
| |
| void analogix_dp_init_analog_param(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = TX_TERMINAL_CTRL_50_OHM; |
| writel(reg, dp->reg_base + ANALOGIX_DP_ANALOG_CTL_1); |
| |
| reg = SEL_24M | TX_DVDD_BIT_1_0625V; |
| writel(reg, dp->reg_base + ANALOGIX_DP_ANALOG_CTL_2); |
| |
| if (dp->plat_data && is_rockchip(dp->plat_data->dev_type)) { |
| reg = REF_CLK_24M; |
| if (dp->plat_data->dev_type == RK3288_DP) |
| reg ^= REF_CLK_MASK; |
| |
| writel(reg, dp->reg_base + ANALOGIX_DP_PLL_REG_1); |
| writel(0x95, dp->reg_base + ANALOGIX_DP_PLL_REG_2); |
| writel(0x40, dp->reg_base + ANALOGIX_DP_PLL_REG_3); |
| writel(0x58, dp->reg_base + ANALOGIX_DP_PLL_REG_4); |
| writel(0x22, dp->reg_base + ANALOGIX_DP_PLL_REG_5); |
| } |
| |
| reg = DRIVE_DVDD_BIT_1_0625V | VCO_BIT_600_MICRO; |
| writel(reg, dp->reg_base + ANALOGIX_DP_ANALOG_CTL_3); |
| |
| reg = PD_RING_OSC | AUX_TERMINAL_CTRL_50_OHM | |
| TX_CUR1_2X | TX_CUR_16_MA; |
| writel(reg, dp->reg_base + ANALOGIX_DP_PLL_FILTER_CTL_1); |
| |
| reg = CH3_AMP_400_MV | CH2_AMP_400_MV | |
| CH1_AMP_400_MV | CH0_AMP_400_MV; |
| writel(reg, dp->reg_base + ANALOGIX_DP_TX_AMP_TUNING_CTL); |
| } |
| |
| void analogix_dp_init_interrupt(struct analogix_dp_device *dp) |
| { |
| /* Set interrupt pin assertion polarity as high */ |
| writel(INT_POL1 | INT_POL0, dp->reg_base + ANALOGIX_DP_INT_CTL); |
| |
| /* Clear pending regisers */ |
| writel(0xff, dp->reg_base + ANALOGIX_DP_COMMON_INT_STA_1); |
| writel(0x4f, dp->reg_base + ANALOGIX_DP_COMMON_INT_STA_2); |
| writel(0xe0, dp->reg_base + ANALOGIX_DP_COMMON_INT_STA_3); |
| writel(0xe7, dp->reg_base + ANALOGIX_DP_COMMON_INT_STA_4); |
| writel(0x63, dp->reg_base + ANALOGIX_DP_INT_STA); |
| |
| /* 0:mask,1: unmask */ |
| writel(0x00, dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_1); |
| writel(0x00, dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_2); |
| writel(0x00, dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_3); |
| writel(0x00, dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_4); |
| writel(0x00, dp->reg_base + ANALOGIX_DP_INT_STA_MASK); |
| } |
| |
| void analogix_dp_reset(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| analogix_dp_stop_video(dp); |
| analogix_dp_enable_video_mute(dp, 0); |
| |
| if (dp->plat_data && is_rockchip(dp->plat_data->dev_type)) |
| reg = RK_VID_CAP_FUNC_EN_N | RK_VID_FIFO_FUNC_EN_N | |
| SW_FUNC_EN_N; |
| else |
| reg = MASTER_VID_FUNC_EN_N | SLAVE_VID_FUNC_EN_N | |
| AUD_FIFO_FUNC_EN_N | AUD_FUNC_EN_N | |
| HDCP_FUNC_EN_N | SW_FUNC_EN_N; |
| |
| writel(reg, dp->reg_base + ANALOGIX_DP_FUNC_EN_1); |
| |
| reg = SSC_FUNC_EN_N | AUX_FUNC_EN_N | |
| SERDES_FIFO_FUNC_EN_N | |
| LS_CLK_DOMAIN_FUNC_EN_N; |
| writel(reg, dp->reg_base + ANALOGIX_DP_FUNC_EN_2); |
| |
| usleep_range(20, 30); |
| |
| analogix_dp_lane_swap(dp, 0); |
| |
| writel(0x0, dp->reg_base + ANALOGIX_DP_SYS_CTL_1); |
| writel(0x40, dp->reg_base + ANALOGIX_DP_SYS_CTL_2); |
| writel(0x0, dp->reg_base + ANALOGIX_DP_SYS_CTL_3); |
| writel(0x0, dp->reg_base + ANALOGIX_DP_SYS_CTL_4); |
| |
| writel(0x0, dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL); |
| writel(0x0, dp->reg_base + ANALOGIX_DP_HDCP_CTL); |
| |
| writel(0x5e, dp->reg_base + ANALOGIX_DP_HPD_DEGLITCH_L); |
| writel(0x1a, dp->reg_base + ANALOGIX_DP_HPD_DEGLITCH_H); |
| |
| writel(0x10, dp->reg_base + ANALOGIX_DP_LINK_DEBUG_CTL); |
| |
| writel(0x0, dp->reg_base + ANALOGIX_DP_PHY_TEST); |
| |
| writel(0x0, dp->reg_base + ANALOGIX_DP_VIDEO_FIFO_THRD); |
| writel(0x20, dp->reg_base + ANALOGIX_DP_AUDIO_MARGIN); |
| |
| writel(0x4, dp->reg_base + ANALOGIX_DP_M_VID_GEN_FILTER_TH); |
| writel(0x2, dp->reg_base + ANALOGIX_DP_M_AUD_GEN_FILTER_TH); |
| |
| writel(0x00000101, dp->reg_base + ANALOGIX_DP_SOC_GENERAL_CTL); |
| } |
| |
| void analogix_dp_swreset(struct analogix_dp_device *dp) |
| { |
| writel(RESET_DP_TX, dp->reg_base + ANALOGIX_DP_TX_SW_RESET); |
| } |
| |
| void analogix_dp_config_interrupt(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| /* 0: mask, 1: unmask */ |
| reg = COMMON_INT_MASK_1; |
| writel(reg, dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_1); |
| |
| reg = COMMON_INT_MASK_2; |
| writel(reg, dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_2); |
| |
| reg = COMMON_INT_MASK_3; |
| writel(reg, dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_3); |
| |
| reg = COMMON_INT_MASK_4; |
| writel(reg, dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_4); |
| |
| reg = INT_STA_MASK; |
| writel(reg, dp->reg_base + ANALOGIX_DP_INT_STA_MASK); |
| } |
| |
| void analogix_dp_mute_hpd_interrupt(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| /* 0: mask, 1: unmask */ |
| reg = readl(dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_4); |
| reg &= ~COMMON_INT_MASK_4; |
| writel(reg, dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_4); |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_INT_STA_MASK); |
| reg &= ~INT_STA_MASK; |
| writel(reg, dp->reg_base + ANALOGIX_DP_INT_STA_MASK); |
| } |
| |
| void analogix_dp_unmute_hpd_interrupt(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| /* 0: mask, 1: unmask */ |
| reg = COMMON_INT_MASK_4; |
| writel(reg, dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_4); |
| |
| reg = INT_STA_MASK; |
| writel(reg, dp->reg_base + ANALOGIX_DP_INT_STA_MASK); |
| } |
| |
| enum pll_status analogix_dp_get_pll_lock_status(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_DEBUG_CTL); |
| if (reg & PLL_LOCK) |
| return PLL_LOCKED; |
| else |
| return PLL_UNLOCKED; |
| } |
| |
| void analogix_dp_set_pll_power_down(struct analogix_dp_device *dp, bool enable) |
| { |
| u32 reg; |
| u32 mask = DP_PLL_PD; |
| u32 pd_addr = ANALOGIX_DP_PLL_CTL; |
| |
| if (dp->plat_data && is_rockchip(dp->plat_data->dev_type)) { |
| pd_addr = ANALOGIX_DP_PD; |
| mask = RK_PLL_PD; |
| } |
| |
| reg = readl(dp->reg_base + pd_addr); |
| if (enable) |
| reg |= mask; |
| else |
| reg &= ~mask; |
| writel(reg, dp->reg_base + pd_addr); |
| } |
| |
| void analogix_dp_set_analog_power_down(struct analogix_dp_device *dp, |
| enum analog_power_block block, |
| bool enable) |
| { |
| u32 reg; |
| u32 phy_pd_addr = ANALOGIX_DP_PHY_PD; |
| u32 mask; |
| |
| if (dp->plat_data && is_rockchip(dp->plat_data->dev_type)) |
| phy_pd_addr = ANALOGIX_DP_PD; |
| |
| switch (block) { |
| case AUX_BLOCK: |
| if (dp->plat_data && is_rockchip(dp->plat_data->dev_type)) |
| mask = RK_AUX_PD; |
| else |
| mask = AUX_PD; |
| |
| reg = readl(dp->reg_base + phy_pd_addr); |
| if (enable) |
| reg |= mask; |
| else |
| reg &= ~mask; |
| writel(reg, dp->reg_base + phy_pd_addr); |
| break; |
| case CH0_BLOCK: |
| mask = CH0_PD; |
| reg = readl(dp->reg_base + phy_pd_addr); |
| |
| if (enable) |
| reg |= mask; |
| else |
| reg &= ~mask; |
| writel(reg, dp->reg_base + phy_pd_addr); |
| break; |
| case CH1_BLOCK: |
| mask = CH1_PD; |
| reg = readl(dp->reg_base + phy_pd_addr); |
| |
| if (enable) |
| reg |= mask; |
| else |
| reg &= ~mask; |
| writel(reg, dp->reg_base + phy_pd_addr); |
| break; |
| case CH2_BLOCK: |
| mask = CH2_PD; |
| reg = readl(dp->reg_base + phy_pd_addr); |
| |
| if (enable) |
| reg |= mask; |
| else |
| reg &= ~mask; |
| writel(reg, dp->reg_base + phy_pd_addr); |
| break; |
| case CH3_BLOCK: |
| mask = CH3_PD; |
| reg = readl(dp->reg_base + phy_pd_addr); |
| |
| if (enable) |
| reg |= mask; |
| else |
| reg &= ~mask; |
| writel(reg, dp->reg_base + phy_pd_addr); |
| break; |
| case ANALOG_TOTAL: |
| /* |
| * There is no bit named DP_PHY_PD, so We used DP_INC_BG |
| * to power off everything instead of DP_PHY_PD in |
| * Rockchip |
| */ |
| if (dp->plat_data && is_rockchip(dp->plat_data->dev_type)) |
| mask = DP_INC_BG; |
| else |
| mask = DP_PHY_PD; |
| |
| reg = readl(dp->reg_base + phy_pd_addr); |
| if (enable) |
| reg |= mask; |
| else |
| reg &= ~mask; |
| |
| writel(reg, dp->reg_base + phy_pd_addr); |
| if (dp->plat_data && is_rockchip(dp->plat_data->dev_type)) |
| usleep_range(10, 15); |
| break; |
| case POWER_ALL: |
| if (enable) { |
| reg = DP_ALL_PD; |
| writel(reg, dp->reg_base + phy_pd_addr); |
| } else { |
| reg = DP_ALL_PD; |
| writel(reg, dp->reg_base + phy_pd_addr); |
| usleep_range(10, 15); |
| reg &= ~DP_INC_BG; |
| writel(reg, dp->reg_base + phy_pd_addr); |
| usleep_range(10, 15); |
| |
| writel(0x00, dp->reg_base + phy_pd_addr); |
| } |
| break; |
| default: |
| break; |
| } |
| } |
| |
| int analogix_dp_init_analog_func(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| int timeout_loop = 0; |
| |
| analogix_dp_set_analog_power_down(dp, POWER_ALL, 0); |
| |
| reg = PLL_LOCK_CHG; |
| writel(reg, dp->reg_base + ANALOGIX_DP_COMMON_INT_STA_1); |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_DEBUG_CTL); |
| reg &= ~(F_PLL_LOCK | PLL_LOCK_CTRL); |
| writel(reg, dp->reg_base + ANALOGIX_DP_DEBUG_CTL); |
| |
| /* Power up PLL */ |
| if (analogix_dp_get_pll_lock_status(dp) == PLL_UNLOCKED) { |
| analogix_dp_set_pll_power_down(dp, 0); |
| |
| while (analogix_dp_get_pll_lock_status(dp) == PLL_UNLOCKED) { |
| timeout_loop++; |
| if (DP_TIMEOUT_LOOP_COUNT < timeout_loop) { |
| dev_err(dp->dev, "failed to get pll lock status\n"); |
| return -ETIMEDOUT; |
| } |
| usleep_range(10, 20); |
| } |
| } |
| |
| /* Enable Serdes FIFO function and Link symbol clock domain module */ |
| reg = readl(dp->reg_base + ANALOGIX_DP_FUNC_EN_2); |
| reg &= ~(SERDES_FIFO_FUNC_EN_N | LS_CLK_DOMAIN_FUNC_EN_N |
| | AUX_FUNC_EN_N); |
| writel(reg, dp->reg_base + ANALOGIX_DP_FUNC_EN_2); |
| return 0; |
| } |
| |
| void analogix_dp_clear_hotplug_interrupts(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| if (gpio_is_valid(dp->hpd_gpio)) |
| return; |
| |
| reg = HOTPLUG_CHG | HPD_LOST | PLUG; |
| writel(reg, dp->reg_base + ANALOGIX_DP_COMMON_INT_STA_4); |
| |
| reg = INT_HPD; |
| writel(reg, dp->reg_base + ANALOGIX_DP_INT_STA); |
| } |
| |
| void analogix_dp_init_hpd(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| if (gpio_is_valid(dp->hpd_gpio)) |
| return; |
| |
| analogix_dp_clear_hotplug_interrupts(dp); |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_3); |
| reg &= ~(F_HPD | HPD_CTRL); |
| writel(reg, dp->reg_base + ANALOGIX_DP_SYS_CTL_3); |
| } |
| |
| void analogix_dp_force_hpd(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_3); |
| reg = (F_HPD | HPD_CTRL); |
| writel(reg, dp->reg_base + ANALOGIX_DP_SYS_CTL_3); |
| } |
| |
| enum dp_irq_type analogix_dp_get_irq_type(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| if (gpio_is_valid(dp->hpd_gpio)) { |
| reg = gpio_get_value(dp->hpd_gpio); |
| if (reg) |
| return DP_IRQ_TYPE_HP_CABLE_IN; |
| else |
| return DP_IRQ_TYPE_HP_CABLE_OUT; |
| } else { |
| /* Parse hotplug interrupt status register */ |
| reg = readl(dp->reg_base + ANALOGIX_DP_COMMON_INT_STA_4); |
| |
| if (reg & PLUG) |
| return DP_IRQ_TYPE_HP_CABLE_IN; |
| |
| if (reg & HPD_LOST) |
| return DP_IRQ_TYPE_HP_CABLE_OUT; |
| |
| if (reg & HOTPLUG_CHG) |
| return DP_IRQ_TYPE_HP_CHANGE; |
| |
| return DP_IRQ_TYPE_UNKNOWN; |
| } |
| } |
| |
| void analogix_dp_reset_aux(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| /* Disable AUX channel module */ |
| reg = readl(dp->reg_base + ANALOGIX_DP_FUNC_EN_2); |
| reg |= AUX_FUNC_EN_N; |
| writel(reg, dp->reg_base + ANALOGIX_DP_FUNC_EN_2); |
| } |
| |
| void analogix_dp_init_aux(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| /* Clear inerrupts related to AUX channel */ |
| reg = RPLY_RECEIV | AUX_ERR; |
| writel(reg, dp->reg_base + ANALOGIX_DP_INT_STA); |
| |
| analogix_dp_set_analog_power_down(dp, AUX_BLOCK, true); |
| usleep_range(10, 11); |
| analogix_dp_set_analog_power_down(dp, AUX_BLOCK, false); |
| |
| analogix_dp_reset_aux(dp); |
| |
| /* AUX_BIT_PERIOD_EXPECTED_DELAY doesn't apply to Rockchip IP */ |
| if (dp->plat_data && is_rockchip(dp->plat_data->dev_type)) |
| reg = 0; |
| else |
| reg = AUX_BIT_PERIOD_EXPECTED_DELAY(3); |
| |
| /* Disable AUX transaction H/W retry */ |
| reg |= AUX_HW_RETRY_COUNT_SEL(0) | |
| AUX_HW_RETRY_INTERVAL_600_MICROSECONDS; |
| |
| writel(reg, dp->reg_base + ANALOGIX_DP_AUX_HW_RETRY_CTL); |
| |
| /* Receive AUX Channel DEFER commands equal to DEFFER_COUNT*64 */ |
| reg = DEFER_CTRL_EN | DEFER_COUNT(1); |
| writel(reg, dp->reg_base + ANALOGIX_DP_AUX_CH_DEFER_CTL); |
| |
| /* Enable AUX channel module */ |
| reg = readl(dp->reg_base + ANALOGIX_DP_FUNC_EN_2); |
| reg &= ~AUX_FUNC_EN_N; |
| writel(reg, dp->reg_base + ANALOGIX_DP_FUNC_EN_2); |
| } |
| |
| int analogix_dp_get_plug_in_status(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| if (gpio_is_valid(dp->hpd_gpio)) { |
| if (gpio_get_value(dp->hpd_gpio)) |
| return 0; |
| } else { |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_3); |
| if (reg & HPD_STATUS) |
| return 0; |
| } |
| |
| return -EINVAL; |
| } |
| |
| void analogix_dp_enable_sw_function(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_FUNC_EN_1); |
| reg &= ~SW_FUNC_EN_N; |
| writel(reg, dp->reg_base + ANALOGIX_DP_FUNC_EN_1); |
| } |
| |
| int analogix_dp_start_aux_transaction(struct analogix_dp_device *dp) |
| { |
| int reg; |
| int retval = 0; |
| int timeout_loop = 0; |
| |
| /* Enable AUX CH operation */ |
| reg = readl(dp->reg_base + ANALOGIX_DP_AUX_CH_CTL_2); |
| reg |= AUX_EN; |
| writel(reg, dp->reg_base + ANALOGIX_DP_AUX_CH_CTL_2); |
| |
| /* Is AUX CH command reply received? */ |
| reg = readl(dp->reg_base + ANALOGIX_DP_INT_STA); |
| while (!(reg & RPLY_RECEIV)) { |
| timeout_loop++; |
| if (DP_TIMEOUT_LOOP_COUNT < timeout_loop) { |
| dev_err(dp->dev, "AUX CH command reply failed!\n"); |
| return -ETIMEDOUT; |
| } |
| reg = readl(dp->reg_base + ANALOGIX_DP_INT_STA); |
| usleep_range(10, 11); |
| } |
| |
| /* Clear interrupt source for AUX CH command reply */ |
| writel(RPLY_RECEIV, dp->reg_base + ANALOGIX_DP_INT_STA); |
| |
| /* Clear interrupt source for AUX CH access error */ |
| reg = readl(dp->reg_base + ANALOGIX_DP_INT_STA); |
| if (reg & AUX_ERR) { |
| writel(AUX_ERR, dp->reg_base + ANALOGIX_DP_INT_STA); |
| return -EREMOTEIO; |
| } |
| |
| /* Check AUX CH error access status */ |
| reg = readl(dp->reg_base + ANALOGIX_DP_AUX_CH_STA); |
| if ((reg & AUX_STATUS_MASK) != 0) { |
| dev_err(dp->dev, "AUX CH error happens: %d\n\n", |
| reg & AUX_STATUS_MASK); |
| return -EREMOTEIO; |
| } |
| |
| return retval; |
| } |
| |
| int analogix_dp_write_byte_to_dpcd(struct analogix_dp_device *dp, |
| unsigned int reg_addr, |
| unsigned char data) |
| { |
| u32 reg; |
| int i; |
| int retval; |
| |
| for (i = 0; i < 3; i++) { |
| /* Clear AUX CH data buffer */ |
| reg = BUF_CLR; |
| writel(reg, dp->reg_base + ANALOGIX_DP_BUFFER_DATA_CTL); |
| |
| /* Select DPCD device address */ |
| reg = AUX_ADDR_7_0(reg_addr); |
| writel(reg, dp->reg_base + ANALOGIX_DP_AUX_ADDR_7_0); |
| reg = AUX_ADDR_15_8(reg_addr); |
| writel(reg, dp->reg_base + ANALOGIX_DP_AUX_ADDR_15_8); |
| reg = AUX_ADDR_19_16(reg_addr); |
| writel(reg, dp->reg_base + ANALOGIX_DP_AUX_ADDR_19_16); |
| |
| /* Write data buffer */ |
| reg = (unsigned int)data; |
| writel(reg, dp->reg_base + ANALOGIX_DP_BUF_DATA_0); |
| |
| /* |
| * Set DisplayPort transaction and write 1 byte |
| * If bit 3 is 1, DisplayPort transaction. |
| * If Bit 3 is 0, I2C transaction. |
| */ |
| reg = AUX_TX_COMM_DP_TRANSACTION | AUX_TX_COMM_WRITE; |
| writel(reg, dp->reg_base + ANALOGIX_DP_AUX_CH_CTL_1); |
| |
| /* Start AUX transaction */ |
| retval = analogix_dp_start_aux_transaction(dp); |
| if (retval == 0) |
| break; |
| |
| dev_dbg(dp->dev, "%s: Aux Transaction fail!\n", __func__); |
| } |
| |
| return retval; |
| } |
| |
| void analogix_dp_set_link_bandwidth(struct analogix_dp_device *dp, u32 bwtype) |
| { |
| u32 reg; |
| |
| reg = bwtype; |
| if ((bwtype == DP_LINK_BW_2_7) || (bwtype == DP_LINK_BW_1_62)) |
| writel(reg, dp->reg_base + ANALOGIX_DP_LINK_BW_SET); |
| } |
| |
| void analogix_dp_get_link_bandwidth(struct analogix_dp_device *dp, u32 *bwtype) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_LINK_BW_SET); |
| *bwtype = reg; |
| } |
| |
| void analogix_dp_set_lane_count(struct analogix_dp_device *dp, u32 count) |
| { |
| u32 reg; |
| |
| reg = count; |
| writel(reg, dp->reg_base + ANALOGIX_DP_LANE_COUNT_SET); |
| } |
| |
| void analogix_dp_get_lane_count(struct analogix_dp_device *dp, u32 *count) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_LANE_COUNT_SET); |
| *count = reg; |
| } |
| |
| void analogix_dp_enable_enhanced_mode(struct analogix_dp_device *dp, |
| bool enable) |
| { |
| u32 reg; |
| |
| if (enable) { |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_4); |
| reg |= ENHANCED; |
| writel(reg, dp->reg_base + ANALOGIX_DP_SYS_CTL_4); |
| } else { |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_4); |
| reg &= ~ENHANCED; |
| writel(reg, dp->reg_base + ANALOGIX_DP_SYS_CTL_4); |
| } |
| } |
| |
| void analogix_dp_set_training_pattern(struct analogix_dp_device *dp, |
| enum pattern_set pattern) |
| { |
| u32 reg; |
| |
| switch (pattern) { |
| case PRBS7: |
| reg = SCRAMBLING_ENABLE | LINK_QUAL_PATTERN_SET_PRBS7; |
| writel(reg, dp->reg_base + ANALOGIX_DP_TRAINING_PTN_SET); |
| break; |
| case D10_2: |
| reg = SCRAMBLING_ENABLE | LINK_QUAL_PATTERN_SET_D10_2; |
| writel(reg, dp->reg_base + ANALOGIX_DP_TRAINING_PTN_SET); |
| break; |
| case TRAINING_PTN1: |
| reg = SCRAMBLING_DISABLE | SW_TRAINING_PATTERN_SET_PTN1; |
| writel(reg, dp->reg_base + ANALOGIX_DP_TRAINING_PTN_SET); |
| break; |
| case TRAINING_PTN2: |
| reg = SCRAMBLING_DISABLE | SW_TRAINING_PATTERN_SET_PTN2; |
| writel(reg, dp->reg_base + ANALOGIX_DP_TRAINING_PTN_SET); |
| break; |
| case DP_NONE: |
| reg = SCRAMBLING_ENABLE | |
| LINK_QUAL_PATTERN_SET_DISABLE | |
| SW_TRAINING_PATTERN_SET_NORMAL; |
| writel(reg, dp->reg_base + ANALOGIX_DP_TRAINING_PTN_SET); |
| break; |
| default: |
| break; |
| } |
| } |
| |
| void analogix_dp_set_lane0_pre_emphasis(struct analogix_dp_device *dp, |
| u32 level) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_LN0_LINK_TRAINING_CTL); |
| reg &= ~PRE_EMPHASIS_SET_MASK; |
| reg |= level << PRE_EMPHASIS_SET_SHIFT; |
| writel(reg, dp->reg_base + ANALOGIX_DP_LN0_LINK_TRAINING_CTL); |
| } |
| |
| void analogix_dp_set_lane1_pre_emphasis(struct analogix_dp_device *dp, |
| u32 level) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_LN1_LINK_TRAINING_CTL); |
| reg &= ~PRE_EMPHASIS_SET_MASK; |
| reg |= level << PRE_EMPHASIS_SET_SHIFT; |
| writel(reg, dp->reg_base + ANALOGIX_DP_LN1_LINK_TRAINING_CTL); |
| } |
| |
| void analogix_dp_set_lane2_pre_emphasis(struct analogix_dp_device *dp, |
| u32 level) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_LN2_LINK_TRAINING_CTL); |
| reg &= ~PRE_EMPHASIS_SET_MASK; |
| reg |= level << PRE_EMPHASIS_SET_SHIFT; |
| writel(reg, dp->reg_base + ANALOGIX_DP_LN2_LINK_TRAINING_CTL); |
| } |
| |
| void analogix_dp_set_lane3_pre_emphasis(struct analogix_dp_device *dp, |
| u32 level) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_LN3_LINK_TRAINING_CTL); |
| reg &= ~PRE_EMPHASIS_SET_MASK; |
| reg |= level << PRE_EMPHASIS_SET_SHIFT; |
| writel(reg, dp->reg_base + ANALOGIX_DP_LN3_LINK_TRAINING_CTL); |
| } |
| |
| void analogix_dp_set_lane0_link_training(struct analogix_dp_device *dp, |
| u32 training_lane) |
| { |
| u32 reg; |
| |
| reg = training_lane; |
| writel(reg, dp->reg_base + ANALOGIX_DP_LN0_LINK_TRAINING_CTL); |
| } |
| |
| void analogix_dp_set_lane1_link_training(struct analogix_dp_device *dp, |
| u32 training_lane) |
| { |
| u32 reg; |
| |
| reg = training_lane; |
| writel(reg, dp->reg_base + ANALOGIX_DP_LN1_LINK_TRAINING_CTL); |
| } |
| |
| void analogix_dp_set_lane2_link_training(struct analogix_dp_device *dp, |
| u32 training_lane) |
| { |
| u32 reg; |
| |
| reg = training_lane; |
| writel(reg, dp->reg_base + ANALOGIX_DP_LN2_LINK_TRAINING_CTL); |
| } |
| |
| void analogix_dp_set_lane3_link_training(struct analogix_dp_device *dp, |
| u32 training_lane) |
| { |
| u32 reg; |
| |
| reg = training_lane; |
| writel(reg, dp->reg_base + ANALOGIX_DP_LN3_LINK_TRAINING_CTL); |
| } |
| |
| u32 analogix_dp_get_lane0_link_training(struct analogix_dp_device *dp) |
| { |
| return readl(dp->reg_base + ANALOGIX_DP_LN0_LINK_TRAINING_CTL); |
| } |
| |
| u32 analogix_dp_get_lane1_link_training(struct analogix_dp_device *dp) |
| { |
| return readl(dp->reg_base + ANALOGIX_DP_LN1_LINK_TRAINING_CTL); |
| } |
| |
| u32 analogix_dp_get_lane2_link_training(struct analogix_dp_device *dp) |
| { |
| return readl(dp->reg_base + ANALOGIX_DP_LN2_LINK_TRAINING_CTL); |
| } |
| |
| u32 analogix_dp_get_lane3_link_training(struct analogix_dp_device *dp) |
| { |
| return readl(dp->reg_base + ANALOGIX_DP_LN3_LINK_TRAINING_CTL); |
| } |
| |
| void analogix_dp_reset_macro(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_PHY_TEST); |
| reg |= MACRO_RST; |
| writel(reg, dp->reg_base + ANALOGIX_DP_PHY_TEST); |
| |
| /* 10 us is the minimum reset time. */ |
| usleep_range(10, 20); |
| |
| reg &= ~MACRO_RST; |
| writel(reg, dp->reg_base + ANALOGIX_DP_PHY_TEST); |
| } |
| |
| void analogix_dp_init_video(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = VSYNC_DET | VID_FORMAT_CHG | VID_CLK_CHG; |
| writel(reg, dp->reg_base + ANALOGIX_DP_COMMON_INT_STA_1); |
| |
| reg = 0x0; |
| writel(reg, dp->reg_base + ANALOGIX_DP_SYS_CTL_1); |
| |
| reg = CHA_CRI(4) | CHA_CTRL; |
| writel(reg, dp->reg_base + ANALOGIX_DP_SYS_CTL_2); |
| |
| reg = 0x0; |
| writel(reg, dp->reg_base + ANALOGIX_DP_SYS_CTL_3); |
| |
| reg = VID_HRES_TH(2) | VID_VRES_TH(0); |
| writel(reg, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_8); |
| } |
| |
| void analogix_dp_set_video_color_format(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| /* Configure the input color depth, color space, dynamic range */ |
| reg = (dp->video_info.dynamic_range << IN_D_RANGE_SHIFT) | |
| (dp->video_info.color_depth << IN_BPC_SHIFT) | |
| (dp->video_info.color_space << IN_COLOR_F_SHIFT); |
| writel(reg, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_2); |
| |
| /* Set Input Color YCbCr Coefficients to ITU601 or ITU709 */ |
| reg = readl(dp->reg_base + ANALOGIX_DP_VIDEO_CTL_3); |
| reg &= ~IN_YC_COEFFI_MASK; |
| if (dp->video_info.ycbcr_coeff) |
| reg |= IN_YC_COEFFI_ITU709; |
| else |
| reg |= IN_YC_COEFFI_ITU601; |
| writel(reg, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_3); |
| } |
| |
| int analogix_dp_is_slave_video_stream_clock_on(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_1); |
| writel(reg, dp->reg_base + ANALOGIX_DP_SYS_CTL_1); |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_1); |
| |
| if (!(reg & DET_STA)) { |
| dev_dbg(dp->dev, "Input stream clock not detected.\n"); |
| return -EINVAL; |
| } |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_2); |
| writel(reg, dp->reg_base + ANALOGIX_DP_SYS_CTL_2); |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_2); |
| dev_dbg(dp->dev, "wait SYS_CTL_2.\n"); |
| |
| if (reg & CHA_STA) { |
| dev_dbg(dp->dev, "Input stream clk is changing\n"); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| void analogix_dp_set_video_cr_mn(struct analogix_dp_device *dp, |
| enum clock_recovery_m_value_type type, |
| u32 m_value, u32 n_value) |
| { |
| u32 reg; |
| |
| if (type == REGISTER_M) { |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_4); |
| reg |= FIX_M_VID; |
| writel(reg, dp->reg_base + ANALOGIX_DP_SYS_CTL_4); |
| reg = m_value & 0xff; |
| writel(reg, dp->reg_base + ANALOGIX_DP_M_VID_0); |
| reg = (m_value >> 8) & 0xff; |
| writel(reg, dp->reg_base + ANALOGIX_DP_M_VID_1); |
| reg = (m_value >> 16) & 0xff; |
| writel(reg, dp->reg_base + ANALOGIX_DP_M_VID_2); |
| |
| reg = n_value & 0xff; |
| writel(reg, dp->reg_base + ANALOGIX_DP_N_VID_0); |
| reg = (n_value >> 8) & 0xff; |
| writel(reg, dp->reg_base + ANALOGIX_DP_N_VID_1); |
| reg = (n_value >> 16) & 0xff; |
| writel(reg, dp->reg_base + ANALOGIX_DP_N_VID_2); |
| } else { |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_4); |
| reg &= ~FIX_M_VID; |
| writel(reg, dp->reg_base + ANALOGIX_DP_SYS_CTL_4); |
| |
| writel(0x00, dp->reg_base + ANALOGIX_DP_N_VID_0); |
| writel(0x80, dp->reg_base + ANALOGIX_DP_N_VID_1); |
| writel(0x00, dp->reg_base + ANALOGIX_DP_N_VID_2); |
| } |
| } |
| |
| void analogix_dp_set_video_timing_mode(struct analogix_dp_device *dp, u32 type) |
| { |
| u32 reg; |
| |
| if (type == VIDEO_TIMING_FROM_CAPTURE) { |
| reg = readl(dp->reg_base + ANALOGIX_DP_VIDEO_CTL_10); |
| reg &= ~FORMAT_SEL; |
| writel(reg, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_10); |
| } else { |
| reg = readl(dp->reg_base + ANALOGIX_DP_VIDEO_CTL_10); |
| reg |= FORMAT_SEL; |
| writel(reg, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_10); |
| } |
| } |
| |
| void analogix_dp_enable_video_master(struct analogix_dp_device *dp, bool enable) |
| { |
| u32 reg; |
| |
| if (enable) { |
| reg = readl(dp->reg_base + ANALOGIX_DP_SOC_GENERAL_CTL); |
| reg &= ~VIDEO_MODE_MASK; |
| reg |= VIDEO_MASTER_MODE_EN | VIDEO_MODE_MASTER_MODE; |
| writel(reg, dp->reg_base + ANALOGIX_DP_SOC_GENERAL_CTL); |
| } else { |
| reg = readl(dp->reg_base + ANALOGIX_DP_SOC_GENERAL_CTL); |
| reg &= ~VIDEO_MODE_MASK; |
| reg |= VIDEO_MODE_SLAVE_MODE; |
| writel(reg, dp->reg_base + ANALOGIX_DP_SOC_GENERAL_CTL); |
| } |
| } |
| |
| void analogix_dp_start_video(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_VIDEO_CTL_1); |
| reg |= VIDEO_EN; |
| writel(reg, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_1); |
| } |
| |
| int analogix_dp_is_video_stream_on(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_3); |
| writel(reg, dp->reg_base + ANALOGIX_DP_SYS_CTL_3); |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_SYS_CTL_3); |
| if (!(reg & STRM_VALID)) { |
| dev_dbg(dp->dev, "Input video stream is not detected.\n"); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| void analogix_dp_config_video_slave_mode(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_FUNC_EN_1); |
| if (dp->plat_data && is_rockchip(dp->plat_data->dev_type)) { |
| reg &= ~(RK_VID_CAP_FUNC_EN_N | RK_VID_FIFO_FUNC_EN_N); |
| } else { |
| reg &= ~(MASTER_VID_FUNC_EN_N | SLAVE_VID_FUNC_EN_N); |
| reg |= MASTER_VID_FUNC_EN_N; |
| } |
| writel(reg, dp->reg_base + ANALOGIX_DP_FUNC_EN_1); |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_VIDEO_CTL_10); |
| reg &= ~INTERACE_SCAN_CFG; |
| reg |= (dp->video_info.interlaced << 2); |
| writel(reg, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_10); |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_VIDEO_CTL_10); |
| reg &= ~VSYNC_POLARITY_CFG; |
| reg |= (dp->video_info.v_sync_polarity << 1); |
| writel(reg, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_10); |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_VIDEO_CTL_10); |
| reg &= ~HSYNC_POLARITY_CFG; |
| reg |= (dp->video_info.h_sync_polarity << 0); |
| writel(reg, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_10); |
| |
| reg = AUDIO_MODE_SPDIF_MODE | VIDEO_MODE_SLAVE_MODE; |
| writel(reg, dp->reg_base + ANALOGIX_DP_SOC_GENERAL_CTL); |
| } |
| |
| void analogix_dp_enable_scrambling(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_TRAINING_PTN_SET); |
| reg &= ~SCRAMBLING_DISABLE; |
| writel(reg, dp->reg_base + ANALOGIX_DP_TRAINING_PTN_SET); |
| } |
| |
| void analogix_dp_disable_scrambling(struct analogix_dp_device *dp) |
| { |
| u32 reg; |
| |
| reg = readl(dp->reg_base + ANALOGIX_DP_TRAINING_PTN_SET); |
| reg |= SCRAMBLING_DISABLE; |
| writel(reg, dp->reg_base + ANALOGIX_DP_TRAINING_PTN_SET); |
| } |
| |
| void analogix_dp_enable_psr_crc(struct analogix_dp_device *dp) |
| { |
| writel(PSR_VID_CRC_ENABLE, dp->reg_base + ANALOGIX_DP_CRC_CON); |
| } |
| |
| static ssize_t analogix_dp_get_psr_status(struct analogix_dp_device *dp) |
| { |
| ssize_t val; |
| u8 status; |
| |
| val = drm_dp_dpcd_readb(&dp->aux, DP_PSR_STATUS, &status); |
| if (val < 0) { |
| dev_err(dp->dev, "PSR_STATUS read failed ret=%zd", val); |
| return val; |
| } |
| return status; |
| } |
| |
| int analogix_dp_send_psr_spd(struct analogix_dp_device *dp, |
| struct edp_vsc_psr *vsc, bool blocking) |
| { |
| unsigned int val; |
| int ret; |
| ssize_t psr_status; |
| |
| /* don't send info frame */ |
| val = readl(dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL); |
| val &= ~IF_EN; |
| writel(val, dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL); |
| |
| /* configure single frame update mode */ |
| writel(PSR_FRAME_UP_TYPE_BURST | PSR_CRC_SEL_HARDWARE, |
| dp->reg_base + ANALOGIX_DP_PSR_FRAME_UPDATE_CTRL); |
| |
| /* configure VSC HB0~HB3 */ |
| writel(vsc->sdp_header.HB0, dp->reg_base + ANALOGIX_DP_SPD_HB0); |
| writel(vsc->sdp_header.HB1, dp->reg_base + ANALOGIX_DP_SPD_HB1); |
| writel(vsc->sdp_header.HB2, dp->reg_base + ANALOGIX_DP_SPD_HB2); |
| writel(vsc->sdp_header.HB3, dp->reg_base + ANALOGIX_DP_SPD_HB3); |
| |
| /* configure reused VSC PB0~PB3, magic number from vendor */ |
| writel(0x00, dp->reg_base + ANALOGIX_DP_SPD_PB0); |
| writel(0x16, dp->reg_base + ANALOGIX_DP_SPD_PB1); |
| writel(0xCE, dp->reg_base + ANALOGIX_DP_SPD_PB2); |
| writel(0x5D, dp->reg_base + ANALOGIX_DP_SPD_PB3); |
| |
| /* configure DB0 / DB1 values */ |
| writel(vsc->DB0, dp->reg_base + ANALOGIX_DP_VSC_SHADOW_DB0); |
| writel(vsc->DB1, dp->reg_base + ANALOGIX_DP_VSC_SHADOW_DB1); |
| |
| /* set reuse spd inforframe */ |
| val = readl(dp->reg_base + ANALOGIX_DP_VIDEO_CTL_3); |
| val |= REUSE_SPD_EN; |
| writel(val, dp->reg_base + ANALOGIX_DP_VIDEO_CTL_3); |
| |
| /* mark info frame update */ |
| val = readl(dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL); |
| val = (val | IF_UP) & ~IF_EN; |
| writel(val, dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL); |
| |
| /* send info frame */ |
| val = readl(dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL); |
| val |= IF_EN; |
| writel(val, dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL); |
| |
| if (!blocking) |
| return 0; |
| |
| ret = readx_poll_timeout(analogix_dp_get_psr_status, dp, psr_status, |
| psr_status >= 0 && |
| ((vsc->DB1 && psr_status == DP_PSR_SINK_ACTIVE_RFB) || |
| (!vsc->DB1 && psr_status == DP_PSR_SINK_INACTIVE)), 1500, |
| DP_TIMEOUT_PSR_LOOP_MS * 1000); |
| if (ret) { |
| dev_warn(dp->dev, "Failed to apply PSR %d\n", ret); |
| return ret; |
| } |
| return 0; |
| } |
| |
| ssize_t analogix_dp_transfer(struct analogix_dp_device *dp, |
| struct drm_dp_aux_msg *msg) |
| { |
| u32 reg; |
| u32 status_reg; |
| u8 *buffer = msg->buffer; |
| unsigned int i; |
| int num_transferred = 0; |
| int ret; |
| |
| /* Buffer size of AUX CH is 16 bytes */ |
| if (WARN_ON(msg->size > 16)) |
| return -E2BIG; |
| |
| /* Clear AUX CH data buffer */ |
| reg = BUF_CLR; |
| writel(reg, dp->reg_base + ANALOGIX_DP_BUFFER_DATA_CTL); |
| |
| switch (msg->request & ~DP_AUX_I2C_MOT) { |
| case DP_AUX_I2C_WRITE: |
| reg = AUX_TX_COMM_WRITE | AUX_TX_COMM_I2C_TRANSACTION; |
| if (msg->request & DP_AUX_I2C_MOT) |
| reg |= AUX_TX_COMM_MOT; |
| break; |
| |
| case DP_AUX_I2C_READ: |
| reg = AUX_TX_COMM_READ | AUX_TX_COMM_I2C_TRANSACTION; |
| if (msg->request & DP_AUX_I2C_MOT) |
| reg |= AUX_TX_COMM_MOT; |
| break; |
| |
| case DP_AUX_NATIVE_WRITE: |
| reg = AUX_TX_COMM_WRITE | AUX_TX_COMM_DP_TRANSACTION; |
| break; |
| |
| case DP_AUX_NATIVE_READ: |
| reg = AUX_TX_COMM_READ | AUX_TX_COMM_DP_TRANSACTION; |
| break; |
| |
| default: |
| return -EINVAL; |
| } |
| |
| reg |= AUX_LENGTH(msg->size); |
| writel(reg, dp->reg_base + ANALOGIX_DP_AUX_CH_CTL_1); |
| |
| /* Select DPCD device address */ |
| reg = AUX_ADDR_7_0(msg->address); |
| writel(reg, dp->reg_base + ANALOGIX_DP_AUX_ADDR_7_0); |
| reg = AUX_ADDR_15_8(msg->address); |
| writel(reg, dp->reg_base + ANALOGIX_DP_AUX_ADDR_15_8); |
| reg = AUX_ADDR_19_16(msg->address); |
| writel(reg, dp->reg_base + ANALOGIX_DP_AUX_ADDR_19_16); |
| |
| if (!(msg->request & DP_AUX_I2C_READ)) { |
| for (i = 0; i < msg->size; i++) { |
| reg = buffer[i]; |
| writel(reg, dp->reg_base + ANALOGIX_DP_BUF_DATA_0 + |
| 4 * i); |
| num_transferred++; |
| } |
| } |
| |
| /* Enable AUX CH operation */ |
| reg = AUX_EN; |
| |
| /* Zero-sized messages specify address-only transactions. */ |
| if (msg->size < 1) |
| reg |= ADDR_ONLY; |
| |
| writel(reg, dp->reg_base + ANALOGIX_DP_AUX_CH_CTL_2); |
| |
| ret = readx_poll_timeout(readl, dp->reg_base + ANALOGIX_DP_AUX_CH_CTL_2, |
| reg, !(reg & AUX_EN), 25, 500 * 1000); |
| if (ret) { |
| dev_err(dp->dev, "AUX CH enable timeout!\n"); |
| goto aux_error; |
| } |
| |
| /* TODO: Wait for an interrupt instead of looping? */ |
| /* Is AUX CH command reply received? */ |
| ret = readx_poll_timeout(readl, dp->reg_base + ANALOGIX_DP_INT_STA, |
| reg, reg & RPLY_RECEIV, 10, 20 * 1000); |
| if (ret) { |
| dev_err(dp->dev, "AUX CH cmd reply timeout!\n"); |
| goto aux_error; |
| } |
| |
| /* Clear interrupt source for AUX CH command reply */ |
| writel(RPLY_RECEIV, dp->reg_base + ANALOGIX_DP_INT_STA); |
| |
| /* Clear interrupt source for AUX CH access error */ |
| reg = readl(dp->reg_base + ANALOGIX_DP_INT_STA); |
| status_reg = readl(dp->reg_base + ANALOGIX_DP_AUX_CH_STA); |
| if ((reg & AUX_ERR) || (status_reg & AUX_STATUS_MASK)) { |
| writel(AUX_ERR, dp->reg_base + ANALOGIX_DP_INT_STA); |
| |
| dev_warn(dp->dev, "AUX CH error happened: %#x (%d)\n", |
| status_reg & AUX_STATUS_MASK, !!(reg & AUX_ERR)); |
| goto aux_error; |
| } |
| |
| if (msg->request & DP_AUX_I2C_READ) { |
| for (i = 0; i < msg->size; i++) { |
| reg = readl(dp->reg_base + ANALOGIX_DP_BUF_DATA_0 + |
| 4 * i); |
| buffer[i] = (unsigned char)reg; |
| num_transferred++; |
| } |
| } |
| |
| /* Check if Rx sends defer */ |
| reg = readl(dp->reg_base + ANALOGIX_DP_AUX_RX_COMM); |
| if (reg == AUX_RX_COMM_AUX_DEFER) |
| msg->reply = DP_AUX_NATIVE_REPLY_DEFER; |
| else if (reg == AUX_RX_COMM_I2C_DEFER) |
| msg->reply = DP_AUX_I2C_REPLY_DEFER; |
| else if ((msg->request & ~DP_AUX_I2C_MOT) == DP_AUX_I2C_WRITE || |
| (msg->request & ~DP_AUX_I2C_MOT) == DP_AUX_I2C_READ) |
| msg->reply = DP_AUX_I2C_REPLY_ACK; |
| else if ((msg->request & ~DP_AUX_I2C_MOT) == DP_AUX_NATIVE_WRITE || |
| (msg->request & ~DP_AUX_I2C_MOT) == DP_AUX_NATIVE_READ) |
| msg->reply = DP_AUX_NATIVE_REPLY_ACK; |
| |
| return num_transferred > 0 ? num_transferred : -EBUSY; |
| |
| aux_error: |
| /* if aux err happen, reset aux */ |
| analogix_dp_init_aux(dp); |
| |
| return -EREMOTEIO; |
| } |