| /* | |
| * Philips UCB1400 touchscreen driver | |
| * | |
| * Author: Nicolas Pitre | |
| * Created: September 25, 2006 | |
| * Copyright: MontaVista Software, Inc. | |
| * | |
| * Spliting done by: Marek Vasut <marek.vasut@gmail.com> | |
| * If something doesnt work and it worked before spliting, e-mail me, | |
| * dont bother Nicolas please ;-) | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License version 2 as | |
| * published by the Free Software Foundation. | |
| * | |
| * This code is heavily based on ucb1x00-*.c copyrighted by Russell King | |
| * covering the UCB1100, UCB1200 and UCB1300.. Support for the UCB1400 has | |
| * been made separate from ucb1x00-core/ucb1x00-ts on Russell's request. | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/init.h> | |
| #include <linux/completion.h> | |
| #include <linux/delay.h> | |
| #include <linux/input.h> | |
| #include <linux/device.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/suspend.h> | |
| #include <linux/slab.h> | |
| #include <linux/kthread.h> | |
| #include <linux/freezer.h> | |
| #include <linux/ucb1400.h> | |
| static int adcsync; | |
| static int ts_delay = 55; /* us */ | |
| static int ts_delay_pressure; /* us */ | |
| /* Switch to interrupt mode. */ | |
| static inline void ucb1400_ts_mode_int(struct snd_ac97 *ac97) | |
| { | |
| ucb1400_reg_write(ac97, UCB_TS_CR, | |
| UCB_TS_CR_TSMX_POW | UCB_TS_CR_TSPX_POW | | |
| UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_GND | | |
| UCB_TS_CR_MODE_INT); | |
| } | |
| /* | |
| * Switch to pressure mode, and read pressure. We don't need to wait | |
| * here, since both plates are being driven. | |
| */ | |
| static inline unsigned int ucb1400_ts_read_pressure(struct ucb1400_ts *ucb) | |
| { | |
| ucb1400_reg_write(ucb->ac97, UCB_TS_CR, | |
| UCB_TS_CR_TSMX_POW | UCB_TS_CR_TSPX_POW | | |
| UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_GND | | |
| UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA); | |
| udelay(ts_delay_pressure); | |
| return ucb1400_adc_read(ucb->ac97, UCB_ADC_INP_TSPY, adcsync); | |
| } | |
| /* | |
| * Switch to X position mode and measure Y plate. We switch the plate | |
| * configuration in pressure mode, then switch to position mode. This | |
| * gives a faster response time. Even so, we need to wait about 55us | |
| * for things to stabilise. | |
| */ | |
| static inline unsigned int ucb1400_ts_read_xpos(struct ucb1400_ts *ucb) | |
| { | |
| ucb1400_reg_write(ucb->ac97, UCB_TS_CR, | |
| UCB_TS_CR_TSMX_GND | UCB_TS_CR_TSPX_POW | | |
| UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA); | |
| ucb1400_reg_write(ucb->ac97, UCB_TS_CR, | |
| UCB_TS_CR_TSMX_GND | UCB_TS_CR_TSPX_POW | | |
| UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA); | |
| ucb1400_reg_write(ucb->ac97, UCB_TS_CR, | |
| UCB_TS_CR_TSMX_GND | UCB_TS_CR_TSPX_POW | | |
| UCB_TS_CR_MODE_POS | UCB_TS_CR_BIAS_ENA); | |
| udelay(ts_delay); | |
| return ucb1400_adc_read(ucb->ac97, UCB_ADC_INP_TSPY, adcsync); | |
| } | |
| /* | |
| * Switch to Y position mode and measure X plate. We switch the plate | |
| * configuration in pressure mode, then switch to position mode. This | |
| * gives a faster response time. Even so, we need to wait about 55us | |
| * for things to stabilise. | |
| */ | |
| static inline unsigned int ucb1400_ts_read_ypos(struct ucb1400_ts *ucb) | |
| { | |
| ucb1400_reg_write(ucb->ac97, UCB_TS_CR, | |
| UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_POW | | |
| UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA); | |
| ucb1400_reg_write(ucb->ac97, UCB_TS_CR, | |
| UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_POW | | |
| UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA); | |
| ucb1400_reg_write(ucb->ac97, UCB_TS_CR, | |
| UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_POW | | |
| UCB_TS_CR_MODE_POS | UCB_TS_CR_BIAS_ENA); | |
| udelay(ts_delay); | |
| return ucb1400_adc_read(ucb->ac97, UCB_ADC_INP_TSPX, adcsync); | |
| } | |
| /* | |
| * Switch to X plate resistance mode. Set MX to ground, PX to | |
| * supply. Measure current. | |
| */ | |
| static inline unsigned int ucb1400_ts_read_xres(struct ucb1400_ts *ucb) | |
| { | |
| ucb1400_reg_write(ucb->ac97, UCB_TS_CR, | |
| UCB_TS_CR_TSMX_GND | UCB_TS_CR_TSPX_POW | | |
| UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA); | |
| return ucb1400_adc_read(ucb->ac97, 0, adcsync); | |
| } | |
| /* | |
| * Switch to Y plate resistance mode. Set MY to ground, PY to | |
| * supply. Measure current. | |
| */ | |
| static inline unsigned int ucb1400_ts_read_yres(struct ucb1400_ts *ucb) | |
| { | |
| ucb1400_reg_write(ucb->ac97, UCB_TS_CR, | |
| UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_POW | | |
| UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA); | |
| return ucb1400_adc_read(ucb->ac97, 0, adcsync); | |
| } | |
| static inline int ucb1400_ts_pen_down(struct snd_ac97 *ac97) | |
| { | |
| unsigned short val = ucb1400_reg_read(ac97, UCB_TS_CR); | |
| return val & (UCB_TS_CR_TSPX_LOW | UCB_TS_CR_TSMX_LOW); | |
| } | |
| static inline void ucb1400_ts_irq_enable(struct snd_ac97 *ac97) | |
| { | |
| ucb1400_reg_write(ac97, UCB_IE_CLEAR, UCB_IE_TSPX); | |
| ucb1400_reg_write(ac97, UCB_IE_CLEAR, 0); | |
| ucb1400_reg_write(ac97, UCB_IE_FAL, UCB_IE_TSPX); | |
| } | |
| static inline void ucb1400_ts_irq_disable(struct snd_ac97 *ac97) | |
| { | |
| ucb1400_reg_write(ac97, UCB_IE_FAL, 0); | |
| } | |
| static void ucb1400_ts_evt_add(struct input_dev *idev, u16 pressure, u16 x, u16 y) | |
| { | |
| input_report_abs(idev, ABS_X, x); | |
| input_report_abs(idev, ABS_Y, y); | |
| input_report_abs(idev, ABS_PRESSURE, pressure); | |
| input_sync(idev); | |
| } | |
| static void ucb1400_ts_event_release(struct input_dev *idev) | |
| { | |
| input_report_abs(idev, ABS_PRESSURE, 0); | |
| input_sync(idev); | |
| } | |
| static void ucb1400_handle_pending_irq(struct ucb1400_ts *ucb) | |
| { | |
| unsigned int isr; | |
| isr = ucb1400_reg_read(ucb->ac97, UCB_IE_STATUS); | |
| ucb1400_reg_write(ucb->ac97, UCB_IE_CLEAR, isr); | |
| ucb1400_reg_write(ucb->ac97, UCB_IE_CLEAR, 0); | |
| if (isr & UCB_IE_TSPX) { | |
| ucb1400_ts_irq_disable(ucb->ac97); | |
| enable_irq(ucb->irq); | |
| } else | |
| printk(KERN_ERR "ucb1400: unexpected IE_STATUS = %#x\n", isr); | |
| } | |
| static int ucb1400_ts_thread(void *_ucb) | |
| { | |
| struct ucb1400_ts *ucb = _ucb; | |
| struct task_struct *tsk = current; | |
| int valid = 0; | |
| struct sched_param param = { .sched_priority = 1 }; | |
| sched_setscheduler(tsk, SCHED_FIFO, ¶m); | |
| set_freezable(); | |
| while (!kthread_should_stop()) { | |
| unsigned int x, y, p; | |
| long timeout; | |
| ucb->ts_restart = 0; | |
| if (ucb->irq_pending) { | |
| ucb->irq_pending = 0; | |
| ucb1400_handle_pending_irq(ucb); | |
| } | |
| ucb1400_adc_enable(ucb->ac97); | |
| x = ucb1400_ts_read_xpos(ucb); | |
| y = ucb1400_ts_read_ypos(ucb); | |
| p = ucb1400_ts_read_pressure(ucb); | |
| ucb1400_adc_disable(ucb->ac97); | |
| /* Switch back to interrupt mode. */ | |
| ucb1400_ts_mode_int(ucb->ac97); | |
| msleep(10); | |
| if (ucb1400_ts_pen_down(ucb->ac97)) { | |
| ucb1400_ts_irq_enable(ucb->ac97); | |
| /* | |
| * If we spat out a valid sample set last time, | |
| * spit out a "pen off" sample here. | |
| */ | |
| if (valid) { | |
| ucb1400_ts_event_release(ucb->ts_idev); | |
| valid = 0; | |
| } | |
| timeout = MAX_SCHEDULE_TIMEOUT; | |
| } else { | |
| valid = 1; | |
| ucb1400_ts_evt_add(ucb->ts_idev, p, x, y); | |
| timeout = msecs_to_jiffies(10); | |
| } | |
| wait_event_freezable_timeout(ucb->ts_wait, | |
| ucb->irq_pending || ucb->ts_restart || | |
| kthread_should_stop(), timeout); | |
| } | |
| /* Send the "pen off" if we are stopping with the pen still active */ | |
| if (valid) | |
| ucb1400_ts_event_release(ucb->ts_idev); | |
| ucb->ts_task = NULL; | |
| return 0; | |
| } | |
| /* | |
| * A restriction with interrupts exists when using the ucb1400, as | |
| * the codec read/write routines may sleep while waiting for codec | |
| * access completion and uses semaphores for access control to the | |
| * AC97 bus. A complete codec read cycle could take anywhere from | |
| * 60 to 100uSec so we *definitely* don't want to spin inside the | |
| * interrupt handler waiting for codec access. So, we handle the | |
| * interrupt by scheduling a RT kernel thread to run in process | |
| * context instead of interrupt context. | |
| */ | |
| static irqreturn_t ucb1400_hard_irq(int irqnr, void *devid) | |
| { | |
| struct ucb1400_ts *ucb = devid; | |
| if (irqnr == ucb->irq) { | |
| disable_irq(ucb->irq); | |
| ucb->irq_pending = 1; | |
| wake_up(&ucb->ts_wait); | |
| return IRQ_HANDLED; | |
| } | |
| return IRQ_NONE; | |
| } | |
| static int ucb1400_ts_open(struct input_dev *idev) | |
| { | |
| struct ucb1400_ts *ucb = input_get_drvdata(idev); | |
| int ret = 0; | |
| BUG_ON(ucb->ts_task); | |
| ucb->ts_task = kthread_run(ucb1400_ts_thread, ucb, "UCB1400_ts"); | |
| if (IS_ERR(ucb->ts_task)) { | |
| ret = PTR_ERR(ucb->ts_task); | |
| ucb->ts_task = NULL; | |
| } | |
| return ret; | |
| } | |
| static void ucb1400_ts_close(struct input_dev *idev) | |
| { | |
| struct ucb1400_ts *ucb = input_get_drvdata(idev); | |
| if (ucb->ts_task) | |
| kthread_stop(ucb->ts_task); | |
| ucb1400_ts_irq_disable(ucb->ac97); | |
| ucb1400_reg_write(ucb->ac97, UCB_TS_CR, 0); | |
| } | |
| #ifndef NO_IRQ | |
| #define NO_IRQ 0 | |
| #endif | |
| /* | |
| * Try to probe our interrupt, rather than relying on lots of | |
| * hard-coded machine dependencies. | |
| */ | |
| static int ucb1400_ts_detect_irq(struct ucb1400_ts *ucb) | |
| { | |
| unsigned long mask, timeout; | |
| mask = probe_irq_on(); | |
| /* Enable the ADC interrupt. */ | |
| ucb1400_reg_write(ucb->ac97, UCB_IE_RIS, UCB_IE_ADC); | |
| ucb1400_reg_write(ucb->ac97, UCB_IE_FAL, UCB_IE_ADC); | |
| ucb1400_reg_write(ucb->ac97, UCB_IE_CLEAR, 0xffff); | |
| ucb1400_reg_write(ucb->ac97, UCB_IE_CLEAR, 0); | |
| /* Cause an ADC interrupt. */ | |
| ucb1400_reg_write(ucb->ac97, UCB_ADC_CR, UCB_ADC_ENA); | |
| ucb1400_reg_write(ucb->ac97, UCB_ADC_CR, UCB_ADC_ENA | UCB_ADC_START); | |
| /* Wait for the conversion to complete. */ | |
| timeout = jiffies + HZ/2; | |
| while (!(ucb1400_reg_read(ucb->ac97, UCB_ADC_DATA) & | |
| UCB_ADC_DAT_VALID)) { | |
| cpu_relax(); | |
| if (time_after(jiffies, timeout)) { | |
| printk(KERN_ERR "ucb1400: timed out in IRQ probe\n"); | |
| probe_irq_off(mask); | |
| return -ENODEV; | |
| } | |
| } | |
| ucb1400_reg_write(ucb->ac97, UCB_ADC_CR, 0); | |
| /* Disable and clear interrupt. */ | |
| ucb1400_reg_write(ucb->ac97, UCB_IE_RIS, 0); | |
| ucb1400_reg_write(ucb->ac97, UCB_IE_FAL, 0); | |
| ucb1400_reg_write(ucb->ac97, UCB_IE_CLEAR, 0xffff); | |
| ucb1400_reg_write(ucb->ac97, UCB_IE_CLEAR, 0); | |
| /* Read triggered interrupt. */ | |
| ucb->irq = probe_irq_off(mask); | |
| if (ucb->irq < 0 || ucb->irq == NO_IRQ) | |
| return -ENODEV; | |
| return 0; | |
| } | |
| static int ucb1400_ts_probe(struct platform_device *dev) | |
| { | |
| int error, x_res, y_res; | |
| struct ucb1400_ts *ucb = dev->dev.platform_data; | |
| ucb->ts_idev = input_allocate_device(); | |
| if (!ucb->ts_idev) { | |
| error = -ENOMEM; | |
| goto err; | |
| } | |
| error = ucb1400_ts_detect_irq(ucb); | |
| if (error) { | |
| printk(KERN_ERR "UCB1400: IRQ probe failed\n"); | |
| goto err_free_devs; | |
| } | |
| init_waitqueue_head(&ucb->ts_wait); | |
| error = request_irq(ucb->irq, ucb1400_hard_irq, IRQF_TRIGGER_RISING, | |
| "UCB1400", ucb); | |
| if (error) { | |
| printk(KERN_ERR "ucb1400: unable to grab irq%d: %d\n", | |
| ucb->irq, error); | |
| goto err_free_devs; | |
| } | |
| printk(KERN_DEBUG "UCB1400: found IRQ %d\n", ucb->irq); | |
| input_set_drvdata(ucb->ts_idev, ucb); | |
| ucb->ts_idev->dev.parent = &dev->dev; | |
| ucb->ts_idev->name = "UCB1400 touchscreen interface"; | |
| ucb->ts_idev->id.vendor = ucb1400_reg_read(ucb->ac97, | |
| AC97_VENDOR_ID1); | |
| ucb->ts_idev->id.product = ucb->id; | |
| ucb->ts_idev->open = ucb1400_ts_open; | |
| ucb->ts_idev->close = ucb1400_ts_close; | |
| ucb->ts_idev->evbit[0] = BIT_MASK(EV_ABS); | |
| ucb1400_adc_enable(ucb->ac97); | |
| x_res = ucb1400_ts_read_xres(ucb); | |
| y_res = ucb1400_ts_read_yres(ucb); | |
| ucb1400_adc_disable(ucb->ac97); | |
| printk(KERN_DEBUG "UCB1400: x/y = %d/%d\n", x_res, y_res); | |
| input_set_abs_params(ucb->ts_idev, ABS_X, 0, x_res, 0, 0); | |
| input_set_abs_params(ucb->ts_idev, ABS_Y, 0, y_res, 0, 0); | |
| input_set_abs_params(ucb->ts_idev, ABS_PRESSURE, 0, 0, 0, 0); | |
| error = input_register_device(ucb->ts_idev); | |
| if (error) | |
| goto err_free_irq; | |
| return 0; | |
| err_free_irq: | |
| free_irq(ucb->irq, ucb); | |
| err_free_devs: | |
| input_free_device(ucb->ts_idev); | |
| err: | |
| return error; | |
| } | |
| static int ucb1400_ts_remove(struct platform_device *dev) | |
| { | |
| struct ucb1400_ts *ucb = dev->dev.platform_data; | |
| free_irq(ucb->irq, ucb); | |
| input_unregister_device(ucb->ts_idev); | |
| return 0; | |
| } | |
| #ifdef CONFIG_PM | |
| static int ucb1400_ts_resume(struct platform_device *dev) | |
| { | |
| struct ucb1400_ts *ucb = platform_get_drvdata(dev); | |
| if (ucb->ts_task) { | |
| /* | |
| * Restart the TS thread to ensure the | |
| * TS interrupt mode is set up again | |
| * after sleep. | |
| */ | |
| ucb->ts_restart = 1; | |
| wake_up(&ucb->ts_wait); | |
| } | |
| return 0; | |
| } | |
| #else | |
| #define ucb1400_ts_resume NULL | |
| #endif | |
| static struct platform_driver ucb1400_ts_driver = { | |
| .probe = ucb1400_ts_probe, | |
| .remove = ucb1400_ts_remove, | |
| .resume = ucb1400_ts_resume, | |
| .driver = { | |
| .name = "ucb1400_ts", | |
| }, | |
| }; | |
| static int __init ucb1400_ts_init(void) | |
| { | |
| return platform_driver_register(&ucb1400_ts_driver); | |
| } | |
| static void __exit ucb1400_ts_exit(void) | |
| { | |
| platform_driver_unregister(&ucb1400_ts_driver); | |
| } | |
| module_param(adcsync, bool, 0444); | |
| MODULE_PARM_DESC(adcsync, "Synchronize touch readings with ADCSYNC pin."); | |
| module_param(ts_delay, int, 0444); | |
| MODULE_PARM_DESC(ts_delay, "Delay between panel setup and" | |
| " position read. Default = 55us."); | |
| module_param(ts_delay_pressure, int, 0444); | |
| MODULE_PARM_DESC(ts_delay_pressure, | |
| "delay between panel setup and pressure read." | |
| " Default = 0us."); | |
| module_init(ucb1400_ts_init); | |
| module_exit(ucb1400_ts_exit); | |
| MODULE_DESCRIPTION("Philips UCB1400 touchscreen driver"); | |
| MODULE_LICENSE("GPL"); |