drivers/input/misc/rb532_button.c

/*
 * Support for the S1 button on Routerboard 532
 *
 * Copyright (C) 2009  Phil Sutter <n0-1@freewrt.org>
 */

#include <linux/input-polldev.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>

#include <asm/mach-rc32434/gpio.h>
#include <asm/mach-rc32434/rb.h>

#define DRV_NAME "rb532-button"

#define RB532_BTN_RATE 100 /* msec */
#define RB532_BTN_KSYM BTN_0

/* The S1 button state is provided by GPIO pin 1. But as this
 * pin is also used for uart input as alternate function, the
 * operational modes must be switched first:
 * 1) disable uart using set_latch_u5()
 * 2) turn off alternate function implicitly through
 *    gpio_direction_input()
 * 3) read the GPIO's current value
 * 4) undo step 2 by enabling alternate function (in this
 *    mode the GPIO direction is fixed, so no change needed)
 * 5) turn on uart again
 * The GPIO value occurs to be inverted, so pin high means
 * button is not pressed.
 */
static bool rb532_button_pressed(void)
{
	int val;

	set_latch_u5(0, LO_FOFF);
	gpio_direction_input(GPIO_BTN_S1);

	val = gpio_get_value(GPIO_BTN_S1);

	rb532_gpio_set_func(GPIO_BTN_S1);
	set_latch_u5(LO_FOFF, 0);

	return !val;
}

static void rb532_button_poll(struct input_polled_dev *poll_dev)
{
	input_report_key(poll_dev->input, RB532_BTN_KSYM,
			 rb532_button_pressed());
	input_sync(poll_dev->input);
}

static int rb532_button_probe(struct platform_device *pdev)
{
	struct input_polled_dev *poll_dev;
	int error;

	poll_dev = input_allocate_polled_device();
	if (!poll_dev)
		return -ENOMEM;

	poll_dev->poll = rb532_button_poll;
	poll_dev->poll_interval = RB532_BTN_RATE;

	poll_dev->input->name = "rb532 button";
	poll_dev->input->phys = "rb532/button0";
	poll_dev->input->id.bustype = BUS_HOST;
	poll_dev->input->dev.parent = &pdev->dev;

	dev_set_drvdata(&pdev->dev, poll_dev);

	input_set_capability(poll_dev->input, EV_KEY, RB532_BTN_KSYM);

	error = input_register_polled_device(poll_dev);
	if (error) {
		input_free_polled_device(poll_dev);
		return error;
	}

	return 0;
}

static int rb532_button_remove(struct platform_device *pdev)
{
	struct input_polled_dev *poll_dev = dev_get_drvdata(&pdev->dev);

	input_unregister_polled_device(poll_dev);
	input_free_polled_device(poll_dev);

	return 0;
}

static struct platform_driver rb532_button_driver = {
	.probe = rb532_button_probe,
	.remove = rb532_button_remove,
	.driver = {
		.name = DRV_NAME,
	},
};
module_platform_driver(rb532_button_driver);

MODULE_AUTHOR("Phil Sutter <n0-1@freewrt.org>");
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Support for S1 button on Routerboard 532");
MODULE_ALIAS("platform:" DRV_NAME);