| /* |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| /dts-v1/; |
| |
| #include <dt-bindings/input/input.h> |
| #include "omap443x.dtsi" |
| #include "motorola-cpcap-mapphone.dtsi" |
| |
| / { |
| model = "Motorola Droid 4 XT894"; |
| compatible = "motorola,droid4", "ti,omap4430", "ti,omap4"; |
| |
| chosen { |
| stdout-path = &uart3; |
| }; |
| |
| aliases { |
| display0 = &lcd0; |
| display1 = &hdmi0; |
| }; |
| |
| /* |
| * We seem to have only 1021 MB accessible, 1021 - 1022 is locked, |
| * then 1023 - 1024 seems to contain mbm. |
| */ |
| memory { |
| device_type = "memory"; |
| reg = <0x80000000 0x3fd00000>; /* 1021 MB */ |
| }; |
| |
| /* Poweroff GPIO probably connected to CPCAP */ |
| gpio-poweroff { |
| compatible = "gpio-poweroff"; |
| pinctrl-0 = <&poweroff_gpio>; |
| pinctrl-names = "default"; |
| gpios = <&gpio2 18 GPIO_ACTIVE_LOW>; /* gpio50 */ |
| }; |
| |
| hdmi0: connector { |
| compatible = "hdmi-connector"; |
| pinctrl-0 = <&hdmi_hpd_gpio>; |
| pinctrl-names = "default"; |
| label = "hdmi"; |
| type = "d"; |
| |
| hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; /* gpio63 */ |
| |
| port { |
| hdmi_connector_in: endpoint { |
| remote-endpoint = <&hdmi_out>; |
| }; |
| }; |
| }; |
| |
| /* |
| * HDMI 5V regulator probably sourced from battery. Let's keep |
| * keep this as always enabled for HDMI to work until we've |
| * figured what the encoder chip is. |
| */ |
| hdmi_regulator: regulator-hdmi { |
| compatible = "regulator-fixed"; |
| regulator-name = "hdmi"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* gpio59 */ |
| enable-active-high; |
| regulator-always-on; |
| }; |
| |
| /* HS USB Host PHY on PORT 1 */ |
| hsusb1_phy: hsusb1_phy { |
| compatible = "usb-nop-xceiv"; |
| }; |
| |
| /* LCD regulator from sw5 source */ |
| lcd_regulator: regulator-lcd { |
| compatible = "regulator-fixed"; |
| regulator-name = "lcd"; |
| regulator-min-microvolt = <5050000>; |
| regulator-max-microvolt = <5050000>; |
| gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>; /* gpio96 */ |
| enable-active-high; |
| vin-supply = <&sw5>; |
| }; |
| |
| /* This is probably coming straight from the battery.. */ |
| wl12xx_vmmc: regulator-wl12xx { |
| compatible = "regulator-fixed"; |
| regulator-name = "vwl1271"; |
| regulator-min-microvolt = <1650000>; |
| regulator-max-microvolt = <1650000>; |
| gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; /* gpio94 */ |
| startup-delay-us = <70000>; |
| enable-active-high; |
| }; |
| |
| gpio_keys { |
| compatible = "gpio-keys"; |
| |
| volume_down { |
| label = "Volume Down"; |
| gpios = <&gpio5 26 GPIO_ACTIVE_LOW>; /* gpio154 */ |
| linux,code = <KEY_VOLUMEDOWN>; |
| linux,can-disable; |
| }; |
| |
| slider { |
| label = "Keypad Slide"; |
| gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */ |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_KEYPAD_SLIDE>; |
| linux,can-disable; |
| |
| }; |
| }; |
| }; |
| |
| &dss { |
| status = "okay"; |
| }; |
| |
| &gpio6 { |
| touchscreen_reset { |
| gpio-hog; |
| gpios = <13 0>; |
| output-high; |
| line-name = "touchscreen-reset"; |
| }; |
| |
| pwm8: dmtimer-pwm-8 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vibrator_direction_pin>; |
| |
| compatible = "ti,omap-dmtimer-pwm"; |
| #pwm-cells = <3>; |
| ti,timers = <&timer8>; |
| ti,clock-source = <0x01>; |
| }; |
| |
| pwm9: dmtimer-pwm-9 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vibrator_enable_pin>; |
| |
| compatible = "ti,omap-dmtimer-pwm"; |
| #pwm-cells = <3>; |
| ti,timers = <&timer9>; |
| ti,clock-source = <0x01>; |
| }; |
| |
| vibrator { |
| compatible = "pwm-vibrator"; |
| pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>; |
| pwm-names = "enable", "direction"; |
| direction-duty-cycle-ns = <10000000>; |
| }; |
| |
| }; |
| |
| &dsi1 { |
| status = "okay"; |
| vdd-supply = <&vcsi>; |
| |
| port { |
| dsi1_out_ep: endpoint { |
| remote-endpoint = <&lcd0_in>; |
| lanes = <0 1 2 3 4 5>; |
| }; |
| }; |
| |
| lcd0: display { |
| compatible = "panel-dsi-cm"; |
| label = "lcd0"; |
| vddi-supply = <&lcd_regulator>; |
| reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* gpio101 */ |
| |
| panel-timing { |
| clock-frequency = <0>; /* Calculated by dsi */ |
| |
| hback-porch = <2>; |
| hactive = <540>; |
| hfront-porch = <0>; |
| hsync-len = <2>; |
| |
| vback-porch = <1>; |
| vactive = <960>; |
| vfront-porch = <0>; |
| vsync-len = <1>; |
| |
| hsync-active = <0>; |
| vsync-active = <0>; |
| de-active = <1>; |
| pixelclk-active = <1>; |
| }; |
| |
| port { |
| lcd0_in: endpoint { |
| remote-endpoint = <&dsi1_out_ep>; |
| }; |
| }; |
| }; |
| }; |
| |
| &hdmi { |
| status = "okay"; |
| pinctrl-0 = <&dss_hdmi_pins>; |
| pinctrl-names = "default"; |
| vdda-supply = <&vdac>; |
| |
| port { |
| hdmi_out: endpoint { |
| remote-endpoint = <&hdmi_connector_in>; |
| lanes = <1 0 3 2 5 4 7 6>; |
| }; |
| }; |
| }; |
| |
| &i2c1 { |
| tmp105@48 { |
| compatible = "ti,tmp105"; |
| reg = <0x48>; |
| pinctrl-0 = <&tmp105_irq>; |
| pinctrl-names = "default"; |
| /* kpd_row0.gpio_178 */ |
| interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING |
| &omap4_pmx_core 0x14e>; |
| interrupt-names = "irq", "wakeup"; |
| wakeup-source; |
| }; |
| }; |
| |
| &keypad { |
| keypad,num-rows = <8>; |
| keypad,num-columns = <8>; |
| linux,keymap = < |
| |
| /* Row 1 */ |
| MATRIX_KEY(0, 2, KEY_1) |
| MATRIX_KEY(0, 6, KEY_2) |
| MATRIX_KEY(2, 3, KEY_3) |
| MATRIX_KEY(0, 7, KEY_4) |
| MATRIX_KEY(0, 4, KEY_5) |
| MATRIX_KEY(5, 5, KEY_6) |
| MATRIX_KEY(0, 1, KEY_7) |
| MATRIX_KEY(0, 5, KEY_8) |
| MATRIX_KEY(0, 0, KEY_9) |
| MATRIX_KEY(1, 6, KEY_0) |
| |
| /* Row 2 */ |
| MATRIX_KEY(3, 4, KEY_APOSTROPHE) |
| MATRIX_KEY(7, 6, KEY_Q) |
| MATRIX_KEY(7, 7, KEY_W) |
| MATRIX_KEY(7, 2, KEY_E) |
| MATRIX_KEY(1, 0, KEY_R) |
| MATRIX_KEY(4, 4, KEY_T) |
| MATRIX_KEY(1, 2, KEY_Y) |
| MATRIX_KEY(6, 7, KEY_U) |
| MATRIX_KEY(2, 2, KEY_I) |
| MATRIX_KEY(5, 6, KEY_O) |
| MATRIX_KEY(3, 7, KEY_P) |
| MATRIX_KEY(6, 5, KEY_BACKSPACE) |
| |
| /* Row 3 */ |
| MATRIX_KEY(5, 4, KEY_TAB) |
| MATRIX_KEY(5, 7, KEY_A) |
| MATRIX_KEY(2, 7, KEY_S) |
| MATRIX_KEY(7, 0, KEY_D) |
| MATRIX_KEY(2, 6, KEY_F) |
| MATRIX_KEY(6, 2, KEY_G) |
| MATRIX_KEY(6, 6, KEY_H) |
| MATRIX_KEY(1, 4, KEY_J) |
| MATRIX_KEY(3, 1, KEY_K) |
| MATRIX_KEY(2, 1, KEY_L) |
| MATRIX_KEY(4, 6, KEY_ENTER) |
| |
| /* Row 4 */ |
| MATRIX_KEY(3, 6, KEY_LEFTSHIFT) /* KEY_CAPSLOCK */ |
| MATRIX_KEY(6, 1, KEY_Z) |
| MATRIX_KEY(7, 4, KEY_X) |
| MATRIX_KEY(5, 1, KEY_C) |
| MATRIX_KEY(1, 7, KEY_V) |
| MATRIX_KEY(2, 4, KEY_B) |
| MATRIX_KEY(4, 1, KEY_N) |
| MATRIX_KEY(1, 1, KEY_M) |
| MATRIX_KEY(3, 5, KEY_COMMA) |
| MATRIX_KEY(5, 2, KEY_DOT) |
| MATRIX_KEY(6, 3, KEY_UP) |
| MATRIX_KEY(7, 3, KEY_OK) |
| |
| /* Row 5 */ |
| MATRIX_KEY(2, 5, KEY_LEFTCTRL) /* KEY_LEFTSHIFT */ |
| MATRIX_KEY(4, 5, KEY_LEFTALT) /* SYM */ |
| MATRIX_KEY(6, 0, KEY_MINUS) |
| MATRIX_KEY(4, 7, KEY_EQUAL) |
| MATRIX_KEY(1, 5, KEY_SPACE) |
| MATRIX_KEY(3, 2, KEY_SLASH) |
| MATRIX_KEY(4, 3, KEY_LEFT) |
| MATRIX_KEY(5, 3, KEY_DOWN) |
| MATRIX_KEY(3, 3, KEY_RIGHT) |
| |
| /* Side buttons, KEY_VOLUMEDOWN and KEY_PWER are on CPCAP? */ |
| MATRIX_KEY(5, 0, KEY_VOLUMEUP) |
| >; |
| }; |
| |
| &mmc1 { |
| vmmc-supply = <&vwlan2>; |
| bus-width = <4>; |
| cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* gpio176 */ |
| }; |
| |
| &mmc2 { |
| vmmc-supply = <&vsdio>; |
| bus-width = <8>; |
| ti,non-removable; |
| }; |
| |
| &mmc3 { |
| vmmc-supply = <&wl12xx_vmmc>; |
| interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH |
| &omap4_pmx_core 0xde>; |
| |
| non-removable; |
| bus-width = <4>; |
| cap-power-off-card; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| wlcore: wlcore@2 { |
| compatible = "ti,wl1285", "ti,wl1283"; |
| reg = <2>; |
| interrupt-parent = <&gpio4>; |
| interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; /* gpio100 */ |
| ref-clock-frequency = <26000000>; |
| tcxo-clock-frequency = <26000000>; |
| }; |
| }; |
| |
| &i2c1 { |
| lm3532@38 { |
| compatible = "ti,lm3532"; |
| reg = <0x38>; |
| |
| enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>; |
| |
| backlight { |
| compatible = "ti,lm3532-backlight"; |
| |
| lcd { |
| led-sources = <0 1 2>; |
| ramp-up-msec = <1>; |
| ramp-down-msec = <0>; |
| }; |
| }; |
| }; |
| }; |
| |
| /* |
| * REVISIT: Add gpio173 reset pin handling to the driver, see gpio-hog above. |
| * If the GPIO reset is used, we probably need to have /lib/firmware/maxtouch.fw |
| * available. See "mxt-app" and "droid4-touchscreen-firmware" tools for more |
| * information. |
| */ |
| &i2c2 { |
| tsp@4a { |
| compatible = "atmel,maxtouch"; |
| reg = <0x4a>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&touchscreen_pins>; |
| |
| /* gpio_183 with sys_nirq2 pad as wakeup */ |
| interrupts-extended = <&gpio6 23 IRQ_TYPE_EDGE_FALLING |
| &omap4_pmx_core 0x160>; |
| interrupt-names = "irq", "wakeup"; |
| wakeup-source; |
| }; |
| |
| isl29030@44 { |
| compatible = "isil,isl29030"; |
| reg = <0x44>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&als_proximity_pins>; |
| |
| interrupt-parent = <&gpio6>; |
| interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */ |
| }; |
| }; |
| |
| &omap4_pmx_core { |
| |
| /* hdmi_hpd.gpio_63 */ |
| hdmi_hpd_gpio: pinmux_hdmi_hpd_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3) |
| >; |
| }; |
| |
| /* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */ |
| dss_hdmi_pins: pinmux_dss_hdmi_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) |
| OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0) |
| OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0) |
| >; |
| }; |
| |
| /* gpmc_ncs0.gpio_50 */ |
| poweroff_gpio: pinmux_poweroff_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3) |
| >; |
| }; |
| |
| /* kpd_row0.gpio_178 */ |
| tmp105_irq: pinmux_tmp105_irq { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3) |
| >; |
| }; |
| |
| usb_gpio_mux_sel1: pinmux_usb_gpio_mux_sel1_pins { |
| /* gpio_60 */ |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) |
| >; |
| }; |
| |
| touchscreen_pins: pinmux_touchscreen_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3) |
| >; |
| }; |
| |
| als_proximity_pins: pinmux_als_proximity_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3) |
| >; |
| }; |
| |
| usb_ulpi_pins: pinmux_usb_ulpi_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x196, MUX_MODE7) |
| OMAP4_IOPAD(0x198, MUX_MODE7) |
| OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0) |
| OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0) |
| OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0) |
| OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0) |
| OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0) |
| OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0) |
| OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0) |
| OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0) |
| OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0) |
| OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0) |
| OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0) |
| OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0) |
| >; |
| }; |
| |
| /* usb0_otg_dp and usb0_otg_dm */ |
| usb_utmi_pins: pinmux_usb_utmi_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0) |
| OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0) |
| OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7) |
| >; |
| }; |
| |
| /* uart3_tx_irtx and uart3_rx_irrx */ |
| uart3_pins: pinmux_uart3_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x196, MUX_MODE7) |
| OMAP4_IOPAD(0x198, MUX_MODE7) |
| OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1ba, MUX_MODE2) |
| OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2) |
| OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7) |
| OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7) |
| >; |
| }; |
| |
| uart4_pins: pinmux_uart4_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0) /* uart4_rx */ |
| OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0) /* uart4_tx */ |
| OMAP4_IOPAD(0x110, PIN_INPUT_PULLUP | MUX_MODE5) /* uart4_cts */ |
| OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5) /* uart4_rts */ |
| >; |
| }; |
| }; |
| |
| &omap4_pmx_wkup { |
| usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins { |
| /* gpio_wk0 */ |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3) |
| >; |
| }; |
| |
| vibrator_direction_pin: pinmux_vibrator_direction_pin { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1) /* dmtimer8_pwm_evt (gpio_27) */ |
| >; |
| }; |
| |
| vibrator_enable_pin: pinmux_vibrator_enable_pin { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1) /* dmtimer9_pwm_evt (gpio_28) */ |
| >; |
| }; |
| }; |
| |
| &uart3 { |
| interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH |
| &omap4_pmx_core 0x17c>; |
| }; |
| |
| &uart4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart4_pins>; |
| |
| bluetooth { |
| compatible = "ti,wl1285-st"; |
| enable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; /* gpio 174 */ |
| max-speed = <3686400>; |
| }; |
| }; |
| |
| &usbhsehci { |
| phys = <&hsusb1_phy>; |
| }; |
| |
| &usbhshost { |
| port1-mode = "ohci-phy-4pin-dpdm"; |
| port2-mode = "ehci-tll"; |
| }; |
| |
| /* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */ |
| &usb_otg_hs { |
| interface-type = <1>; |
| mode = <3>; |
| power = <50>; |
| }; |
| |
| &i2c4 { |
| ak8975: magnetometer@c { |
| compatible = "asahi-kasei,ak8975"; |
| reg = <0x0c>; |
| |
| vdd-supply = <&vhvio>; |
| |
| interrupt-parent = <&gpio6>; |
| interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */ |
| |
| rotation-matrix = "-1", "0", "0", |
| "0", "1", "0", |
| "0", "0", "-1"; |
| |
| }; |
| |
| lis3dh: accelerometer@18 { |
| compatible = "st,lis3dh-accel"; |
| reg = <0x18>; |
| |
| vdd-supply = <&vhvio>; |
| |
| interrupt-parent = <&gpio2>; |
| interrupts = <2 IRQ_TYPE_EDGE_BOTH>; /* gpio34 */ |
| |
| rotation-matrix = "0", "-1", "0", |
| "1", "0", "0", |
| "0", "0", "1"; |
| }; |
| }; |
