| /* |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| chosen { |
| stdout-path = &uart1; |
| }; |
| |
| cpus { |
| cpu@0 { |
| cpu0-supply = <&vcc>; |
| }; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x80000000 0>; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| user0 { |
| label = "user0"; |
| gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* LEDA */ |
| linux,default-trigger = "none"; |
| }; |
| }; |
| |
| wl12xx_vmmc: wl12xx_vmmc { |
| compatible = "regulator-fixed"; |
| regulator-name = "vwl1271"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| gpio = <&gpio5 29 0>; /* gpio157 */ |
| startup-delay-us = <70000>; |
| enable-active-high; |
| vin-supply = <&vmmc2>; |
| }; |
| }; |
| |
| &gpmc { |
| ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */ |
| |
| nand@0,0 { |
| compatible = "ti,omap2-nand"; |
| reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ |
| interrupt-parent = <&gpmc>; |
| interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ |
| <1 IRQ_TYPE_NONE>; /* termcount */ |
| linux,mtd-name = "micron,mt29f4g16abbda3w"; |
| nand-bus-width = <16>; |
| ti,nand-ecc-opt = "bch8"; |
| rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */ |
| gpmc,sync-clk-ps = <0>; |
| gpmc,cs-on-ns = <0>; |
| gpmc,cs-rd-off-ns = <44>; |
| gpmc,cs-wr-off-ns = <44>; |
| gpmc,adv-on-ns = <6>; |
| gpmc,adv-rd-off-ns = <34>; |
| gpmc,adv-wr-off-ns = <44>; |
| gpmc,we-off-ns = <40>; |
| gpmc,oe-off-ns = <54>; |
| gpmc,access-ns = <64>; |
| gpmc,rd-cycle-ns = <82>; |
| gpmc,wr-cycle-ns = <82>; |
| gpmc,wr-access-ns = <40>; |
| gpmc,wr-data-mux-bus-ns = <0>; |
| gpmc,device-width = <2>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| /* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */ |
| |
| x-loader@0 { |
| label = "x-loader"; |
| reg = <0 0x80000>; |
| }; |
| |
| bootloaders@80000 { |
| label = "u-boot"; |
| reg = <0x80000 0x1e0000>; |
| }; |
| |
| bootloaders_env@260000 { |
| label = "u-boot-env"; |
| reg = <0x260000 0x20000>; |
| }; |
| |
| kernel@280000 { |
| label = "kernel"; |
| reg = <0x280000 0x400000>; |
| }; |
| |
| filesystem@680000 { |
| label = "fs"; |
| reg = <0x680000 0>; /* 0 = MTDPART_SIZ_FULL */ |
| }; |
| }; |
| }; |
| |
| &i2c1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c1_pins>; |
| clock-frequency = <2600000>; |
| |
| twl: twl@48 { |
| reg = <0x48>; |
| interrupts = <7>; /* SYS_NIRQ cascaded to intc */ |
| interrupt-parent = <&intc>; |
| twl_audio: audio { |
| compatible = "ti,twl4030-audio"; |
| codec { |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <400000>; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <400000>; |
| at24@50 { |
| compatible = "atmel,24c64"; |
| readonly; |
| reg = <0x50>; |
| }; |
| }; |
| |
| /* |
| * Only found on the wireless SOM. For the SOM without wireless, the pins for |
| * MMC3 can be routed with jumpers to the second MMC slot on the devkit and |
| * gpio157 is not connected. So this should be OK to keep common for now, |
| * probably device tree overlays is the way to go with the various SOM and |
| * jumpering combinations for the long run. |
| */ |
| &mmc3 { |
| interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>; |
| pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>; |
| pinctrl-names = "default"; |
| vmmc-supply = <&wl12xx_vmmc>; |
| non-removable; |
| bus-width = <4>; |
| cap-power-off-card; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| wlcore: wlcore@2 { |
| compatible = "ti,wl1283"; |
| reg = <2>; |
| interrupt-parent = <&gpio5>; |
| interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */ |
| ref-clock-frequency = <26000000>; |
| tcxo-clock-frequency = <26000000>; |
| }; |
| }; |
| |
| &omap3_pmx_core { |
| mmc3_pins: pinmux_mm3_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */ |
| OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ |
| OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ |
| OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ |
| OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ |
| OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */ |
| >; |
| }; |
| mcbsp2_pins: pinmux_mcbsp2_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */ |
| OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */ |
| OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */ |
| OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */ |
| >; |
| }; |
| uart2_pins: pinmux_uart2_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */ |
| OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/ |
| OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ |
| OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ |
| OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */ |
| >; |
| }; |
| mcspi1_pins: pinmux_mcspi1_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ |
| OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ |
| OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ |
| OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ |
| >; |
| }; |
| hsusb_otg_pins: pinmux_hsusb_otg_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ |
| OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ |
| OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ |
| OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ |
| |
| OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */ |
| OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ |
| OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ |
| OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */ |
| OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */ |
| OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */ |
| OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */ |
| OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ |
| >; |
| }; |
| i2c1_pins: pinmux_i2c1_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ |
| OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ |
| >; |
| }; |
| }; |
| |
| &uart2 { |
| interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart2_pins>; |
| }; |
| |
| &mcspi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcspi1_pins>; |
| }; |
| |
| &omap3_pmx_core2 { |
| mmc3_core2_pins: pinmux_mmc3_core2_pins { |
| pinctrl-single,pins = < |
| OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ |
| OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ |
| >; |
| }; |
| }; |
| |
| #include "twl4030.dtsi" |
| #include "twl4030_omap3.dtsi" |
| |
| &twl { |
| twl_power: power { |
| compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle"; |
| ti,use_poweroff; |
| }; |
| }; |
| |
| &twl_gpio { |
| ti,use-leds; |
| }; |
