blob: c1ebc1065fc167114fbcded5a22762bfea269aa8 [file] [log] [blame] [edit]
/*
* Copyright 2010 Tilera Corporation. All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation, version 2.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or
* NON INFRINGEMENT. See the GNU General Public License for
* more details.
*/
#include <linux/export.h>
#include <asm/page.h>
#include <asm/cacheflush.h>
#include <arch/icache.h>
#include <arch/spr_def.h>
void __flush_icache_range(unsigned long start, unsigned long end)
{
invalidate_icache((const void *)start, end - start, PAGE_SIZE);
}
/* Force a load instruction to issue. */
static inline void force_load(char *p)
{
*(volatile char *)p;
}
/*
* Flush and invalidate a VA range that is homed remotely on a single
* core (if "!hfh") or homed via hash-for-home (if "hfh"), waiting
* until the memory controller holds the flushed values.
*/
void __attribute__((optimize("omit-frame-pointer")))
finv_buffer_remote(void *buffer, size_t size, int hfh)
{
char *p, *base;
size_t step_size, load_count;
/*
* On TILEPro the striping granularity is a fixed 8KB; on
* TILE-Gx it is configurable, and we rely on the fact that
* the hypervisor always configures maximum striping, so that
* bits 9 and 10 of the PA are part of the stripe function, so
* every 512 bytes we hit a striping boundary.
*
*/
#ifdef __tilegx__
const unsigned long STRIPE_WIDTH = 512;
#else
const unsigned long STRIPE_WIDTH = 8192;
#endif
#ifdef __tilegx__
/*
* On TILE-Gx, we must disable the dstream prefetcher before doing
* a cache flush; otherwise, we could end up with data in the cache
* that we don't want there. Note that normally we'd do an mf
* after the SPR write to disabling the prefetcher, but we do one
* below, before any further loads, so there's no need to do it
* here.
*/
uint_reg_t old_dstream_pf = __insn_mfspr(SPR_DSTREAM_PF);
__insn_mtspr(SPR_DSTREAM_PF, 0);
#endif
/*
* Flush and invalidate the buffer out of the local L1/L2
* and request the home cache to flush and invalidate as well.
*/
__finv_buffer(buffer, size);
/*
* Wait for the home cache to acknowledge that it has processed
* all the flush-and-invalidate requests. This does not mean
* that the flushed data has reached the memory controller yet,
* but it does mean the home cache is processing the flushes.
*/
__insn_mf();
/*
* Issue a load to the last cache line, which can't complete
* until all the previously-issued flushes to the same memory
* controller have also completed. If we weren't striping
* memory, that one load would be sufficient, but since we may
* be, we also need to back up to the last load issued to
* another memory controller, which would be the point where
* we crossed a "striping" boundary (the granularity of striping
* across memory controllers). Keep backing up and doing this
* until we are before the beginning of the buffer, or have
* hit all the controllers.
*
* If we are flushing a hash-for-home buffer, it's even worse.
* Each line may be homed on a different tile, and each tile
* may have up to four lines that are on different
* controllers. So as we walk backwards, we have to touch
* enough cache lines to satisfy these constraints. In
* practice this ends up being close enough to "load from
* every cache line on a full memory stripe on each
* controller" that we simply do that, to simplify the logic.
*
* On TILE-Gx the hash-for-home function is much more complex,
* with the upshot being we can't readily guarantee we have
* hit both entries in the 128-entry AMT that were hit by any
* load in the entire range, so we just re-load them all.
* With larger buffers, we may want to consider using a hypervisor
* trap to issue loads directly to each hash-for-home tile for
* each controller (doing it from Linux would trash the TLB).
*/
if (hfh) {
step_size = L2_CACHE_BYTES;
#ifdef __tilegx__
load_count = (size + L2_CACHE_BYTES - 1) / L2_CACHE_BYTES;
#else
load_count = (STRIPE_WIDTH / L2_CACHE_BYTES) *
(1 << CHIP_LOG_NUM_MSHIMS());
#endif
} else {
step_size = STRIPE_WIDTH;
load_count = (1 << CHIP_LOG_NUM_MSHIMS());
}
/* Load the last byte of the buffer. */
p = (char *)buffer + size - 1;
force_load(p);
/* Bump down to the end of the previous stripe or cache line. */
p -= step_size;
p = (char *)((unsigned long)p | (step_size - 1));
/* Figure out how far back we need to go. */
base = p - (step_size * (load_count - 2));
if ((unsigned long)base < (unsigned long)buffer)
base = buffer;
/* Fire all the loads we need. */
for (; p >= base; p -= step_size)
force_load(p);
/*
* Repeat, but with finv's instead of loads, to get rid of the
* data we just loaded into our own cache and the old home L3.
* The finv's are guaranteed not to actually flush the data in
* the buffer back to their home, since we just read it, so the
* lines are clean in cache; we will only invalidate those lines.
*/
p = (char *)buffer + size - 1;
__insn_finv(p);
p -= step_size;
p = (char *)((unsigned long)p | (step_size - 1));
for (; p >= base; p -= step_size)
__insn_finv(p);
/* Wait for these finv's (and thus the first finvs) to be done. */
__insn_mf();
#ifdef __tilegx__
/* Reenable the prefetcher. */
__insn_mtspr(SPR_DSTREAM_PF, old_dstream_pf);
#endif
}
EXPORT_SYMBOL_GPL(finv_buffer_remote);