| /* |
| * Custom OID/ioctl definitions for |
| * Broadcom 802.11abg Networking Device Driver |
| * |
| * Definitions subject to change without notice. |
| * |
| * Copyright (C) 1999-2017, Broadcom Corporation |
| * |
| * Unless you and Broadcom execute a separate written software license |
| * agreement governing use of this software, this software is licensed to you |
| * under the terms of the GNU General Public License version 2 (the "GPL"), |
| * available at http://www.broadcom.com/licenses/GPLv2.php, with the |
| * following added to such license: |
| * |
| * As a special exception, the copyright holders of this software give you |
| * permission to link this software with independent modules, and to copy and |
| * distribute the resulting executable under terms of your choice, provided that |
| * you also meet, for each linked independent module, the terms and conditions of |
| * the license of that module. An independent module is a module which is not |
| * derived from this software. The special exception does not apply to any |
| * modifications of the software. |
| * |
| * Notwithstanding the above, under no circumstances may you combine this |
| * software in any way with any other Broadcom software provided under a license |
| * other than the GPL, without Broadcom's express prior written consent. |
| * |
| * |
| * <<Broadcom-WL-IPTag/Open:>> |
| * |
| * $Id: wlioctl_defs.h 655604 2016-08-22 16:49:21Z $ |
| */ |
| |
| |
| #ifndef wlioctl_defs_h |
| #define wlioctl_defs_h |
| |
| |
| |
| |
| /* All builds use the new 11ac ratespec/chanspec */ |
| #undef D11AC_IOTYPES |
| #define D11AC_IOTYPES |
| |
| /* WL_RSPEC defines for rate information */ |
| #define WL_RSPEC_RATE_MASK 0x000000FF /* rate or HT MCS value */ |
| #define WL_RSPEC_VHT_MCS_MASK 0x0000000F /* VHT MCS value */ |
| #define WL_RSPEC_VHT_NSS_MASK 0x000000F0 /* VHT Nss value */ |
| #define WL_RSPEC_VHT_NSS_SHIFT 4 /* VHT Nss value shift */ |
| #define WL_RSPEC_TXEXP_MASK 0x00000300 |
| #define WL_RSPEC_TXEXP_SHIFT 8 |
| #define WL_RSPEC_BW_MASK 0x00070000 /* bandwidth mask */ |
| #define WL_RSPEC_BW_SHIFT 16 /* bandwidth shift */ |
| #define WL_RSPEC_STBC 0x00100000 /* STBC encoding, Nsts = 2 x Nss */ |
| #define WL_RSPEC_TXBF 0x00200000 /* bit indicates TXBF mode */ |
| #define WL_RSPEC_LDPC 0x00400000 /* bit indicates adv coding in use */ |
| #define WL_RSPEC_SGI 0x00800000 /* Short GI mode */ |
| #define WL_RSPEC_ENCODING_MASK 0x03000000 /* Encoding of Rate/MCS field */ |
| #define WL_RSPEC_OVERRIDE_RATE 0x40000000 /* bit indicate to override mcs only */ |
| #define WL_RSPEC_OVERRIDE_MODE 0x80000000 /* bit indicates override both rate & mode */ |
| |
| /* WL_RSPEC_ENCODING field defs */ |
| #define WL_RSPEC_ENCODE_RATE 0x00000000 /* Legacy rate is stored in RSPEC_RATE_MASK */ |
| #define WL_RSPEC_ENCODE_HT 0x01000000 /* HT MCS is stored in RSPEC_RATE_MASK */ |
| #define WL_RSPEC_ENCODE_VHT 0x02000000 /* VHT MCS and Nss is stored in RSPEC_RATE_MASK */ |
| |
| /* WL_RSPEC_BW field defs */ |
| #define WL_RSPEC_BW_UNSPECIFIED 0 |
| #define WL_RSPEC_BW_20MHZ 0x00010000 |
| #define WL_RSPEC_BW_40MHZ 0x00020000 |
| #define WL_RSPEC_BW_80MHZ 0x00030000 |
| #define WL_RSPEC_BW_160MHZ 0x00040000 |
| #define WL_RSPEC_BW_10MHZ 0x00050000 |
| #define WL_RSPEC_BW_5MHZ 0x00060000 |
| #define WL_RSPEC_BW_2P5MHZ 0x00070000 |
| |
| /* Legacy defines for the nrate iovar */ |
| #define OLD_NRATE_MCS_INUSE 0x00000080 /* MSC in use,indicates b0-6 holds an mcs */ |
| #define OLD_NRATE_RATE_MASK 0x0000007f /* rate/mcs value */ |
| #define OLD_NRATE_STF_MASK 0x0000ff00 /* stf mode mask: siso, cdd, stbc, sdm */ |
| #define OLD_NRATE_STF_SHIFT 8 /* stf mode shift */ |
| #define OLD_NRATE_OVERRIDE 0x80000000 /* bit indicates override both rate & mode */ |
| #define OLD_NRATE_OVERRIDE_MCS_ONLY 0x40000000 /* bit indicate to override mcs only */ |
| #define OLD_NRATE_SGI 0x00800000 /* sgi mode */ |
| #define OLD_NRATE_LDPC_CODING 0x00400000 /* bit indicates adv coding in use */ |
| |
| #define OLD_NRATE_STF_SISO 0 /* stf mode SISO */ |
| #define OLD_NRATE_STF_CDD 1 /* stf mode CDD */ |
| #define OLD_NRATE_STF_STBC 2 /* stf mode STBC */ |
| #define OLD_NRATE_STF_SDM 3 /* stf mode SDM */ |
| |
| #define HIGHEST_SINGLE_STREAM_MCS 7 /* MCS values greater than this enable multiple streams */ |
| #define WLC_11N_N_PROP_MCS 6 |
| #define WLC_11N_FIRST_PROP_MCS 87 |
| #define WLC_11N_LAST_PROP_MCS 102 |
| |
| #define MAX_CCA_CHANNELS 38 /* Max number of 20 Mhz wide channels */ |
| #define MAX_CCA_SECS 60 /* CCA keeps this many seconds history */ |
| |
| #define IBSS_MED 15 /* Mediom in-bss congestion percentage */ |
| #define IBSS_HI 25 /* Hi in-bss congestion percentage */ |
| #define OBSS_MED 12 |
| #define OBSS_HI 25 |
| #define INTERFER_MED 5 |
| #define INTERFER_HI 10 |
| |
| #define CCA_FLAG_2G_ONLY 0x01 /* Return a channel from 2.4 Ghz band */ |
| #define CCA_FLAG_5G_ONLY 0x02 /* Return a channel from 2.4 Ghz band */ |
| #define CCA_FLAG_IGNORE_DURATION 0x04 /* Ignore dwell time for each channel */ |
| #define CCA_FLAGS_PREFER_1_6_11 0x10 |
| #define CCA_FLAG_IGNORE_INTERFER 0x20 /* do not exlude channel based on interfer level */ |
| |
| #define CCA_ERRNO_BAND 1 /* After filtering for band pref, no choices left */ |
| #define CCA_ERRNO_DURATION 2 /* After filtering for duration, no choices left */ |
| #define CCA_ERRNO_PREF_CHAN 3 /* After filtering for chan pref, no choices left */ |
| #define CCA_ERRNO_INTERFER 4 /* After filtering for interference, no choices left */ |
| #define CCA_ERRNO_TOO_FEW 5 /* Only 1 channel was input */ |
| |
| #define WL_STA_AID(a) ((a) &~ 0xc000) |
| |
| /* Flags for sta_info_t indicating properties of STA */ |
| #define WL_STA_BRCM 0x00000001 /* Running a Broadcom driver */ |
| #define WL_STA_WME 0x00000002 /* WMM association */ |
| #define WL_STA_NONERP 0x00000004 /* No ERP */ |
| #define WL_STA_AUTHE 0x00000008 /* Authenticated */ |
| #define WL_STA_ASSOC 0x00000010 /* Associated */ |
| #define WL_STA_AUTHO 0x00000020 /* Authorized */ |
| #define WL_STA_WDS 0x00000040 /* Wireless Distribution System */ |
| #define WL_STA_WDS_LINKUP 0x00000080 /* WDS traffic/probes flowing properly */ |
| #define WL_STA_PS 0x00000100 /* STA is in power save mode from AP's viewpoint */ |
| #define WL_STA_APSD_BE 0x00000200 /* APSD delv/trigger for AC_BE is default enabled */ |
| #define WL_STA_APSD_BK 0x00000400 /* APSD delv/trigger for AC_BK is default enabled */ |
| #define WL_STA_APSD_VI 0x00000800 /* APSD delv/trigger for AC_VI is default enabled */ |
| #define WL_STA_APSD_VO 0x00001000 /* APSD delv/trigger for AC_VO is default enabled */ |
| #define WL_STA_N_CAP 0x00002000 /* STA 802.11n capable */ |
| #define WL_STA_SCBSTATS 0x00004000 /* Per STA debug stats */ |
| #define WL_STA_AMPDU_CAP 0x00008000 /* STA AMPDU capable */ |
| #define WL_STA_AMSDU_CAP 0x00010000 /* STA AMSDU capable */ |
| #define WL_STA_MIMO_PS 0x00020000 /* mimo ps mode is enabled */ |
| #define WL_STA_MIMO_RTS 0x00040000 /* send rts in mimo ps mode */ |
| #define WL_STA_RIFS_CAP 0x00080000 /* rifs enabled */ |
| #define WL_STA_VHT_CAP 0x00100000 /* STA VHT(11ac) capable */ |
| #define WL_STA_WPS 0x00200000 /* WPS state */ |
| #define WL_STA_DWDS_CAP 0x01000000 /* DWDS CAP */ |
| #define WL_STA_DWDS 0x02000000 /* DWDS active */ |
| #define WL_WDS_LINKUP WL_STA_WDS_LINKUP /* deprecated */ |
| |
| /* STA HT cap fields */ |
| #define WL_STA_CAP_LDPC_CODING 0x0001 /* Support for rx of LDPC coded pkts */ |
| #define WL_STA_CAP_40MHZ 0x0002 /* FALSE:20Mhz, TRUE:20/40MHZ supported */ |
| #define WL_STA_CAP_MIMO_PS_MASK 0x000C /* Mimo PS mask */ |
| #define WL_STA_CAP_MIMO_PS_SHIFT 0x0002 /* Mimo PS shift */ |
| #define WL_STA_CAP_MIMO_PS_OFF 0x0003 /* Mimo PS, no restriction */ |
| #define WL_STA_CAP_MIMO_PS_RTS 0x0001 /* Mimo PS, send RTS/CTS around MIMO frames */ |
| #define WL_STA_CAP_MIMO_PS_ON 0x0000 /* Mimo PS, MIMO disallowed */ |
| #define WL_STA_CAP_GF 0x0010 /* Greenfield preamble support */ |
| #define WL_STA_CAP_SHORT_GI_20 0x0020 /* 20MHZ short guard interval support */ |
| #define WL_STA_CAP_SHORT_GI_40 0x0040 /* 40Mhz short guard interval support */ |
| #define WL_STA_CAP_TX_STBC 0x0080 /* Tx STBC support */ |
| #define WL_STA_CAP_RX_STBC_MASK 0x0300 /* Rx STBC mask */ |
| #define WL_STA_CAP_RX_STBC_SHIFT 8 /* Rx STBC shift */ |
| #define WL_STA_CAP_DELAYED_BA 0x0400 /* delayed BA support */ |
| #define WL_STA_CAP_MAX_AMSDU 0x0800 /* Max AMSDU size in bytes , 0=3839, 1=7935 */ |
| #define WL_STA_CAP_DSSS_CCK 0x1000 /* DSSS/CCK supported by the BSS */ |
| #define WL_STA_CAP_PSMP 0x2000 /* Power Save Multi Poll support */ |
| #define WL_STA_CAP_40MHZ_INTOLERANT 0x4000 /* 40MHz Intolerant */ |
| #define WL_STA_CAP_LSIG_TXOP 0x8000 /* L-SIG TXOP protection support */ |
| |
| #define WL_STA_CAP_RX_STBC_NO 0x0 /* no rx STBC support */ |
| #define WL_STA_CAP_RX_STBC_ONE_STREAM 0x1 /* rx STBC support of 1 spatial stream */ |
| #define WL_STA_CAP_RX_STBC_TWO_STREAM 0x2 /* rx STBC support of 1-2 spatial streams */ |
| #define WL_STA_CAP_RX_STBC_THREE_STREAM 0x3 /* rx STBC support of 1-3 spatial streams */ |
| |
| /* scb vht flags */ |
| #define WL_STA_VHT_LDPCCAP 0x0001 |
| #define WL_STA_SGI80 0x0002 |
| #define WL_STA_SGI160 0x0004 |
| #define WL_STA_VHT_TX_STBCCAP 0x0008 |
| #define WL_STA_VHT_RX_STBCCAP 0x0010 |
| #define WL_STA_SU_BEAMFORMER 0x0020 |
| #define WL_STA_SU_BEAMFORMEE 0x0040 |
| #define WL_STA_MU_BEAMFORMER 0x0080 |
| #define WL_STA_MU_BEAMFORMEE 0x0100 |
| #define WL_STA_VHT_TXOP_PS 0x0200 |
| #define WL_STA_HTC_VHT_CAP 0x0400 |
| |
| /* Values for TX Filter override mode */ |
| #define WLC_TXFILTER_OVERRIDE_DISABLED 0 |
| #define WLC_TXFILTER_OVERRIDE_ENABLED 1 |
| |
| #define WL_IOCTL_ACTION_GET 0x0 |
| #define WL_IOCTL_ACTION_SET 0x1 |
| #define WL_IOCTL_ACTION_OVL_IDX_MASK 0x1e |
| #define WL_IOCTL_ACTION_OVL_RSV 0x20 |
| #define WL_IOCTL_ACTION_OVL 0x40 |
| #define WL_IOCTL_ACTION_MASK 0x7e |
| #define WL_IOCTL_ACTION_OVL_SHIFT 1 |
| |
| /* For WLC_SET_INFRA ioctl & infra_configuration iovar SET/GET operations */ |
| #define WL_BSSTYPE_INDEP 0 |
| #define WL_BSSTYPE_INFRA 1 |
| #define WL_BSSTYPE_ANY 2 /* deprecated */ |
| #define WL_BSSTYPE_MESH 3 |
| /* Bitmask for scan_type */ |
| #define WL_SCANFLAGS_PASSIVE 0x01 /* force passive scan */ |
| #define WL_SCANFLAGS_RESERVED 0x02 /* Reserved */ |
| #define WL_SCANFLAGS_PROHIBITED 0x04 /* allow scanning prohibited channels */ |
| #define WL_SCANFLAGS_OFFCHAN 0x08 /* allow scanning/reporting off-channel APs */ |
| #define WL_SCANFLAGS_HOTSPOT 0x10 /* automatic ANQP to hotspot APs */ |
| #define WL_SCANFLAGS_SWTCHAN 0x20 /* Force channel switch for differerent bandwidth */ |
| #define WL_SCANFLAGS_FORCE_PARALLEL 0x40 /* Force parallel scan even when actcb_fn_t is on. |
| * by default parallel scan will be disabled if actcb_fn_t |
| * is provided. |
| */ |
| #define WL_SCANFLAGS_SISO 0x40 /* Use 1 RX chain for scanning */ |
| #define WL_SCANFLAGS_MIMO 0x80 /* Force MIMO scanning */ |
| |
| /* wl_iscan_results status values */ |
| #define WL_SCAN_RESULTS_SUCCESS 0 |
| #define WL_SCAN_RESULTS_PARTIAL 1 |
| #define WL_SCAN_RESULTS_PENDING 2 |
| #define WL_SCAN_RESULTS_ABORTED 3 |
| #define WL_SCAN_RESULTS_NO_MEM 4 |
| |
| #define SCANOL_ENABLED (1 << 0) |
| #define SCANOL_BCAST_SSID (1 << 1) |
| #define SCANOL_NOTIFY_BCAST_SSID (1 << 2) |
| #define SCANOL_RESULTS_PER_CYCLE (1 << 3) |
| |
| /* scan times in milliseconds */ |
| #define SCANOL_HOME_TIME 45 /* for home channel processing */ |
| #define SCANOL_ASSOC_TIME 20 /* dwell on a channel while associated */ |
| #define SCANOL_UNASSOC_TIME 40 /* dwell on a channel while unassociated */ |
| #define SCANOL_PASSIVE_TIME 110 /* listen on a channelfor passive scan */ |
| #define SCANOL_AWAY_LIMIT 100 /* max time to be away from home channel */ |
| #define SCANOL_IDLE_REST_TIME 40 |
| #define SCANOL_IDLE_REST_MULTIPLIER 0 |
| #define SCANOL_ACTIVE_REST_TIME 20 |
| #define SCANOL_ACTIVE_REST_MULTIPLIER 0 |
| #define SCANOL_CYCLE_IDLE_REST_TIME 300000 /* Idle Rest Time between Scan Cycle (msec) */ |
| #define SCANOL_CYCLE_IDLE_REST_MULTIPLIER 0 /* Idle Rest Time Multiplier */ |
| #define SCANOL_CYCLE_ACTIVE_REST_TIME 200 |
| #define SCANOL_CYCLE_ACTIVE_REST_MULTIPLIER 0 |
| #define SCANOL_MAX_REST_TIME 3600000 /* max rest time between scan cycle (msec) */ |
| #define SCANOL_CYCLE_DEFAULT 0 /* default for Max Scan Cycle, 0 = forever */ |
| #define SCANOL_CYCLE_MAX 864000 /* Max Scan Cycle */ |
| /* 10 sec/scan cycle => 100 days */ |
| #define SCANOL_NPROBES 2 /* for Active scan; send n probes on each channel */ |
| #define SCANOL_NPROBES_MAX 5 /* for Active scan; send n probes on each channel */ |
| #define SCANOL_SCAN_START_DLY 10 /* delay start of offload scan (sec) */ |
| #define SCANOL_SCAN_START_DLY_MAX 240 /* delay start of offload scan (sec) */ |
| #define SCANOL_MULTIPLIER_MAX 10 /* Max Multiplier */ |
| #define SCANOL_UNASSOC_TIME_MAX 100 /* max dwell on a channel while unassociated */ |
| #define SCANOL_PASSIVE_TIME_MAX 500 /* max listen on a channel for passive scan */ |
| #define SCANOL_SSID_MAX 16 /* max supported preferred SSID */ |
| |
| /* masks for channel and ssid count */ |
| #define WL_SCAN_PARAMS_COUNT_MASK 0x0000ffff |
| #define WL_SCAN_PARAMS_NSSID_SHIFT 16 |
| |
| #define WL_SCAN_ACTION_START 1 |
| #define WL_SCAN_ACTION_CONTINUE 2 |
| #define WL_SCAN_ACTION_ABORT 3 |
| |
| #define ANTENNA_NUM_1 1 /* total number of antennas to be used */ |
| #define ANTENNA_NUM_2 2 |
| #define ANTENNA_NUM_3 3 |
| #define ANTENNA_NUM_4 4 |
| |
| #define ANT_SELCFG_AUTO 0x80 /* bit indicates antenna sel AUTO */ |
| #define ANT_SELCFG_MASK 0x33 /* antenna configuration mask */ |
| #define ANT_SELCFG_TX_UNICAST 0 /* unicast tx antenna configuration */ |
| #define ANT_SELCFG_RX_UNICAST 1 /* unicast rx antenna configuration */ |
| #define ANT_SELCFG_TX_DEF 2 /* default tx antenna configuration */ |
| #define ANT_SELCFG_RX_DEF 3 /* default rx antenna configuration */ |
| |
| /* interference source detection and identification mode */ |
| #define ITFR_MODE_DISABLE 0 /* disable feature */ |
| #define ITFR_MODE_MANUAL_ENABLE 1 /* enable manual detection */ |
| #define ITFR_MODE_AUTO_ENABLE 2 /* enable auto detection */ |
| |
| /* bit definitions for flags in interference source report */ |
| #define ITFR_INTERFERENCED 1 /* interference detected */ |
| #define ITFR_HOME_CHANNEL 2 /* home channel has interference */ |
| #define ITFR_NOISY_ENVIRONMENT 4 /* noisy environemnt so feature stopped */ |
| |
| #define WL_NUM_RPI_BINS 8 |
| #define WL_RM_TYPE_BASIC 1 |
| #define WL_RM_TYPE_CCA 2 |
| #define WL_RM_TYPE_RPI 3 |
| #define WL_RM_TYPE_ABORT -1 /* ABORT any in-progress RM request */ |
| |
| #define WL_RM_FLAG_PARALLEL (1<<0) |
| |
| #define WL_RM_FLAG_LATE (1<<1) |
| #define WL_RM_FLAG_INCAPABLE (1<<2) |
| #define WL_RM_FLAG_REFUSED (1<<3) |
| |
| /* flags */ |
| #define WLC_ASSOC_REQ_IS_REASSOC 0x01 /* assoc req was actually a reassoc */ |
| |
| #define WLC_CIS_DEFAULT 0 /* built-in default */ |
| #define WLC_CIS_SROM 1 /* source is sprom */ |
| #define WLC_CIS_OTP 2 /* source is otp */ |
| |
| /* PCL - Power Control Loop */ |
| /* current gain setting is replaced by user input */ |
| #define WL_ATTEN_APP_INPUT_PCL_OFF 0 /* turn off PCL, apply supplied input */ |
| #define WL_ATTEN_PCL_ON 1 /* turn on PCL */ |
| /* current gain setting is maintained */ |
| #define WL_ATTEN_PCL_OFF 2 /* turn off PCL. */ |
| |
| /* defines used by poweridx iovar - it controls power in a-band */ |
| /* current gain setting is maintained */ |
| #define WL_PWRIDX_PCL_OFF -2 /* turn off PCL. */ |
| #define WL_PWRIDX_PCL_ON -1 /* turn on PCL */ |
| #define WL_PWRIDX_LOWER_LIMIT -2 /* lower limit */ |
| #define WL_PWRIDX_UPPER_LIMIT 63 /* upper limit */ |
| /* value >= 0 causes |
| * - input to be set to that value |
| * - PCL to be off |
| */ |
| |
| #define BCM_MAC_STATUS_INDICATION (0x40010200L) |
| |
| /* Values for TX Filter override mode */ |
| #define WLC_TXFILTER_OVERRIDE_DISABLED 0 |
| #define WLC_TXFILTER_OVERRIDE_ENABLED 1 |
| |
| /* magic pattern used for mismatch driver and wl */ |
| #define WL_TXFIFO_SZ_MAGIC 0xa5a5 |
| |
| /* check this magic number */ |
| #define WLC_IOCTL_MAGIC 0x14e46c77 |
| |
| |
| /* bss_info_cap_t flags */ |
| #define WL_BSS_FLAGS_FROM_BEACON 0x01 /* bss_info derived from beacon */ |
| #define WL_BSS_FLAGS_FROM_CACHE 0x02 /* bss_info collected from cache */ |
| #define WL_BSS_FLAGS_RSSI_ONCHANNEL 0x04 /* rssi info received on channel (vs offchannel) */ |
| #define WL_BSS_FLAGS_HS20 0x08 /* hotspot 2.0 capable */ |
| #define WL_BSS_FLAGS_RSSI_INVALID 0x10 /* BSS contains invalid RSSI */ |
| #define WL_BSS_FLAGS_RSSI_INACCURATE 0x20 /* BSS contains inaccurate RSSI */ |
| #define WL_BSS_FLAGS_SNR_INVALID 0x40 /* BSS contains invalid SNR */ |
| #define WL_BSS_FLAGS_NF_INVALID 0x80 /* BSS contains invalid noise floor */ |
| |
| /* bit definitions for bcnflags in wl_bss_info */ |
| #define WL_BSS_BCNFLAGS_INTERWORK_PRESENT 0x01 /* beacon had IE, accessnet valid */ |
| #define WL_BSS_BCNFLAGS_INTERWORK_PRESENT_VALID 0x02 /* on indicates support for this API */ |
| |
| /* bssinfo flag for nbss_cap */ |
| #define VHT_BI_SGI_80MHZ 0x00000100 |
| #define VHT_BI_80MHZ 0x00000200 |
| #define VHT_BI_160MHZ 0x00000400 |
| #define VHT_BI_8080MHZ 0x00000800 |
| |
| /* reference to wl_ioctl_t struct used by usermode driver */ |
| #define ioctl_subtype set /* subtype param */ |
| #define ioctl_pid used /* pid param */ |
| #define ioctl_status needed /* status param */ |
| |
| |
| /* Enumerate crypto algorithms */ |
| #define CRYPTO_ALGO_OFF 0 |
| #define CRYPTO_ALGO_WEP1 1 |
| #define CRYPTO_ALGO_TKIP 2 |
| #define CRYPTO_ALGO_WEP128 3 |
| #define CRYPTO_ALGO_AES_CCM 4 |
| #define CRYPTO_ALGO_AES_OCB_MSDU 5 |
| #define CRYPTO_ALGO_AES_OCB_MPDU 6 |
| #if !defined(BCMEXTCCX) |
| #define CRYPTO_ALGO_NALG 7 |
| #else |
| #define CRYPTO_ALGO_CKIP 7 |
| #define CRYPTO_ALGO_CKIP_MMH 8 |
| #define CRYPTO_ALGO_WEP_MMH 9 |
| #define CRYPTO_ALGO_NALG 10 |
| #endif |
| |
| #define CRYPTO_ALGO_SMS4 11 |
| #define CRYPTO_ALGO_PMK 12 /* for 802.1x supp to set PMK before 4-way */ |
| #define CRYPTO_ALGO_BIP 13 /* 802.11w BIP (aes cmac) */ |
| |
| #define CRYPTO_ALGO_AES_GCM 14 /* 128 bit GCM */ |
| #define CRYPTO_ALGO_AES_CCM256 15 /* 256 bit CCM */ |
| #define CRYPTO_ALGO_AES_GCM256 16 /* 256 bit GCM */ |
| #define CRYPTO_ALGO_BIP_CMAC256 17 /* 256 bit BIP CMAC */ |
| #define CRYPTO_ALGO_BIP_GMAC 18 /* 128 bit BIP GMAC */ |
| #define CRYPTO_ALGO_BIP_GMAC256 19 /* 256 bit BIP GMAC */ |
| |
| #define CRYPTO_ALGO_NONE CRYPTO_ALGO_OFF |
| |
| /* algo bit vector */ |
| #define KEY_ALGO_MASK(_algo) (1 << _algo) |
| |
| #if defined(BCMEXTCCX) |
| #define KEY_ALGO_MASK_CCX (KEY_ALGO_MASK(CRYPTO_ALGO_CKIP) | \ |
| KEY_ALGO_MASK(CRYPTO_ALGO_CKIP_MMH) | \ |
| KEY_ALGO_MASK(CRYPTO_ALGO_WEP_MMH)) |
| #endif |
| |
| #define KEY_ALGO_MASK_WEP (KEY_ALGO_MASK(CRYPTO_ALGO_WEP1) | \ |
| KEY_ALGO_MASK(CRYPTO_ALGO_WEP128) | \ |
| KEY_ALGO_MASK(CRYPTO_ALGO_NALG)) |
| |
| #define KEY_ALGO_MASK_AES (KEY_ALGO_MASK(CRYPTO_ALGO_AES_CCM) | \ |
| KEY_ALGO_MASK(CRYPTO_ALGO_AES_CCM256) | \ |
| KEY_ALGO_MASK(CRYPTO_ALGO_AES_GCM) | \ |
| KEY_ALGO_MASK(CRYPTO_ALGO_AES_GCM256)) |
| #define KEY_ALGO_MASK_TKIP (KEY_ALGO_MASK(CRYPTO_ALGO_TKIP)) |
| #define KEY_ALGO_MASK_WAPI (KEY_ALGO_MASK(CRYPTO_ALGO_SMS4)) |
| |
| #define WSEC_GEN_MIC_ERROR 0x0001 |
| #define WSEC_GEN_REPLAY 0x0002 |
| #define WSEC_GEN_ICV_ERROR 0x0004 |
| #define WSEC_GEN_MFP_ACT_ERROR 0x0008 |
| #define WSEC_GEN_MFP_DISASSOC_ERROR 0x0010 |
| #define WSEC_GEN_MFP_DEAUTH_ERROR 0x0020 |
| |
| #define WL_SOFT_KEY (1 << 0) /* Indicates this key is using soft encrypt */ |
| #define WL_PRIMARY_KEY (1 << 1) /* Indicates this key is the primary (ie tx) key */ |
| #if defined(BCMEXTCCX) |
| #define WL_CKIP_KP (1 << 4) /* CMIC */ |
| #define WL_CKIP_MMH (1 << 5) /* CKIP */ |
| #else |
| #define WL_KF_RES_4 (1 << 4) /* Reserved for backward compat */ |
| #define WL_KF_RES_5 (1 << 5) /* Reserved for backward compat */ |
| #endif |
| #define WL_IBSS_PEER_GROUP_KEY (1 << 6) /* Indicates a group key for a IBSS PEER */ |
| |
| /* wireless security bitvec */ |
| #define WEP_ENABLED 0x0001 |
| #define TKIP_ENABLED 0x0002 |
| #define AES_ENABLED 0x0004 |
| #define WSEC_SWFLAG 0x0008 |
| #define SES_OW_ENABLED 0x0040 /* to go into transition mode without setting wep */ |
| #ifdef BCMWAPI_WPI |
| #define SMS4_ENABLED 0x0100 |
| #endif /* BCMWAPI_WPI */ |
| |
| #define WSEC_WEP_ENABLED(wsec) ((wsec) & WEP_ENABLED) |
| #define WSEC_TKIP_ENABLED(wsec) ((wsec) & TKIP_ENABLED) |
| #define WSEC_AES_ENABLED(wsec) ((wsec) & AES_ENABLED) |
| |
| #ifdef BCMWAPI_WPI |
| #define WSEC_ENABLED(wsec) ((wsec) & (WEP_ENABLED | TKIP_ENABLED | AES_ENABLED | SMS4_ENABLED)) |
| #else /* BCMWAPI_WPI */ |
| #define WSEC_ENABLED(wsec) ((wsec) & (WEP_ENABLED | TKIP_ENABLED | AES_ENABLED)) |
| #endif /* BCMWAPI_WPI */ |
| |
| #define WSEC_SES_OW_ENABLED(wsec) ((wsec) & SES_OW_ENABLED) |
| #ifdef BCMWAPI_WAI |
| #define WSEC_SMS4_ENABLED(wsec) ((wsec) & SMS4_ENABLED) |
| #endif /* BCMWAPI_WAI */ |
| |
| |
| /* Following macros are not used any more. Just kept here to |
| * avoid build issue in BISON/CARIBOU branch |
| */ |
| #define MFP_CAPABLE 0x0200 |
| #define MFP_REQUIRED 0x0400 |
| #define MFP_SHA256 0x0800 /* a special configuration for STA for WIFI test tool */ |
| |
| /* WPA authentication mode bitvec */ |
| #define WPA_AUTH_DISABLED 0x0000 /* Legacy (i.e., non-WPA) */ |
| #define WPA_AUTH_NONE 0x0001 /* none (IBSS) */ |
| #define WPA_AUTH_UNSPECIFIED 0x0002 /* over 802.1x */ |
| #define WPA_AUTH_PSK 0x0004 /* Pre-shared key */ |
| #if defined(BCMEXTCCX) |
| #define WPA_AUTH_CCKM 0x0008 /* CCKM */ |
| #define WPA2_AUTH_CCKM 0x0010 /* CCKM2 */ |
| #endif |
| /* #define WPA_AUTH_8021X 0x0020 */ /* 802.1x, reserved */ |
| #define WPA2_AUTH_UNSPECIFIED 0x0040 /* over 802.1x */ |
| #define WPA2_AUTH_PSK 0x0080 /* Pre-shared key */ |
| #define BRCM_AUTH_PSK 0x0100 /* BRCM specific PSK */ |
| #define BRCM_AUTH_DPT 0x0200 /* DPT PSK without group keys */ |
| #if defined(BCMWAPI_WAI) || defined(BCMWAPI_WPI) |
| #define WPA_AUTH_WAPI 0x0400 |
| #define WAPI_AUTH_NONE WPA_AUTH_NONE /* none (IBSS) */ |
| #define WAPI_AUTH_UNSPECIFIED 0x0400 /* over AS */ |
| #define WAPI_AUTH_PSK 0x0800 /* Pre-shared key */ |
| #endif /* BCMWAPI_WAI || BCMWAPI_WPI */ |
| #define WPA2_AUTH_1X_SHA256 0x1000 /* 1X with SHA256 key derivation */ |
| #define WPA2_AUTH_TPK 0x2000 /* TDLS Peer Key */ |
| #define WPA2_AUTH_FT 0x4000 /* Fast Transition. */ |
| #define WPA2_AUTH_PSK_SHA256 0x8000 /* PSK with SHA256 key derivation */ |
| /* WPA2_AUTH_SHA256 not used anymore. Just kept here to avoid build issue in DINGO */ |
| #define WPA2_AUTH_SHA256 0x8000 |
| #define WPA_AUTH_PFN_ANY 0xffffffff /* for PFN, match only ssid */ |
| |
| /* pmkid */ |
| #define MAXPMKID 16 |
| |
| /* SROM12 changes */ |
| #define WLC_IOCTL_MAXLEN 8192 /* max length ioctl buffer required */ |
| |
| |
| #define WLC_IOCTL_SMLEN 256 /* "small" length ioctl buffer required */ |
| #define WLC_IOCTL_MEDLEN 1536 /* "med" length ioctl buffer required */ |
| #if defined(LCNCONF) || defined(LCN40CONF) || defined(LCN20CONF) |
| #define WLC_SAMPLECOLLECT_MAXLEN 8192 /* Max Sample Collect buffer */ |
| #else |
| #define WLC_SAMPLECOLLECT_MAXLEN 10240 /* Max Sample Collect buffer for two cores */ |
| #endif |
| #define WLC_SAMPLECOLLECT_MAXLEN_LCN40 8192 |
| |
| /* common ioctl definitions */ |
| #define WLC_GET_MAGIC 0 |
| #define WLC_GET_VERSION 1 |
| #define WLC_UP 2 |
| #define WLC_DOWN 3 |
| #define WLC_GET_LOOP 4 |
| #define WLC_SET_LOOP 5 |
| #define WLC_DUMP 6 |
| #define WLC_GET_MSGLEVEL 7 |
| #define WLC_SET_MSGLEVEL 8 |
| #define WLC_GET_PROMISC 9 |
| #define WLC_SET_PROMISC 10 |
| /* #define WLC_OVERLAY_IOCTL 11 */ /* not supported */ |
| #define WLC_GET_RATE 12 |
| #define WLC_GET_MAX_RATE 13 |
| #define WLC_GET_INSTANCE 14 |
| /* #define WLC_GET_FRAG 15 */ /* no longer supported */ |
| /* #define WLC_SET_FRAG 16 */ /* no longer supported */ |
| /* #define WLC_GET_RTS 17 */ /* no longer supported */ |
| /* #define WLC_SET_RTS 18 */ /* no longer supported */ |
| #define WLC_GET_INFRA 19 |
| #define WLC_SET_INFRA 20 |
| #define WLC_GET_AUTH 21 |
| #define WLC_SET_AUTH 22 |
| #define WLC_GET_BSSID 23 |
| #define WLC_SET_BSSID 24 |
| #define WLC_GET_SSID 25 |
| #define WLC_SET_SSID 26 |
| #define WLC_RESTART 27 |
| #define WLC_TERMINATED 28 |
| /* #define WLC_DUMP_SCB 28 */ /* no longer supported */ |
| #define WLC_GET_CHANNEL 29 |
| #define WLC_SET_CHANNEL 30 |
| #define WLC_GET_SRL 31 |
| #define WLC_SET_SRL 32 |
| #define WLC_GET_LRL 33 |
| #define WLC_SET_LRL 34 |
| #define WLC_GET_PLCPHDR 35 |
| #define WLC_SET_PLCPHDR 36 |
| #define WLC_GET_RADIO 37 |
| #define WLC_SET_RADIO 38 |
| #define WLC_GET_PHYTYPE 39 |
| #define WLC_DUMP_RATE 40 |
| #define WLC_SET_RATE_PARAMS 41 |
| #define WLC_GET_FIXRATE 42 |
| #define WLC_SET_FIXRATE 43 |
| /* #define WLC_GET_WEP 42 */ /* no longer supported */ |
| /* #define WLC_SET_WEP 43 */ /* no longer supported */ |
| #define WLC_GET_KEY 44 |
| #define WLC_SET_KEY 45 |
| #define WLC_GET_REGULATORY 46 |
| #define WLC_SET_REGULATORY 47 |
| #define WLC_GET_PASSIVE_SCAN 48 |
| #define WLC_SET_PASSIVE_SCAN 49 |
| #define WLC_SCAN 50 |
| #define WLC_SCAN_RESULTS 51 |
| #define WLC_DISASSOC 52 |
| #define WLC_REASSOC 53 |
| #define WLC_GET_ROAM_TRIGGER 54 |
| #define WLC_SET_ROAM_TRIGGER 55 |
| #define WLC_GET_ROAM_DELTA 56 |
| #define WLC_SET_ROAM_DELTA 57 |
| #define WLC_GET_ROAM_SCAN_PERIOD 58 |
| #define WLC_SET_ROAM_SCAN_PERIOD 59 |
| #define WLC_EVM 60 /* diag */ |
| #define WLC_GET_TXANT 61 |
| #define WLC_SET_TXANT 62 |
| #define WLC_GET_ANTDIV 63 |
| #define WLC_SET_ANTDIV 64 |
| /* #define WLC_GET_TXPWR 65 */ /* no longer supported */ |
| /* #define WLC_SET_TXPWR 66 */ /* no longer supported */ |
| #define WLC_GET_CLOSED 67 |
| #define WLC_SET_CLOSED 68 |
| #define WLC_GET_MACLIST 69 |
| #define WLC_SET_MACLIST 70 |
| #define WLC_GET_RATESET 71 |
| #define WLC_SET_RATESET 72 |
| /* #define WLC_GET_LOCALE 73 */ /* no longer supported */ |
| #define WLC_LONGTRAIN 74 |
| #define WLC_GET_BCNPRD 75 |
| #define WLC_SET_BCNPRD 76 |
| #define WLC_GET_DTIMPRD 77 |
| #define WLC_SET_DTIMPRD 78 |
| #define WLC_GET_SROM 79 |
| #define WLC_SET_SROM 80 |
| #define WLC_GET_WEP_RESTRICT 81 |
| #define WLC_SET_WEP_RESTRICT 82 |
| #define WLC_GET_COUNTRY 83 |
| #define WLC_SET_COUNTRY 84 |
| #define WLC_GET_PM 85 |
| #define WLC_SET_PM 86 |
| #define WLC_GET_WAKE 87 |
| #define WLC_SET_WAKE 88 |
| /* #define WLC_GET_D11CNTS 89 */ /* -> "counters" iovar */ |
| #define WLC_GET_FORCELINK 90 /* ndis only */ |
| #define WLC_SET_FORCELINK 91 /* ndis only */ |
| #define WLC_FREQ_ACCURACY 92 /* diag */ |
| #define WLC_CARRIER_SUPPRESS 93 /* diag */ |
| #define WLC_GET_PHYREG 94 |
| #define WLC_SET_PHYREG 95 |
| #define WLC_GET_RADIOREG 96 |
| #define WLC_SET_RADIOREG 97 |
| #define WLC_GET_REVINFO 98 |
| #define WLC_GET_UCANTDIV 99 |
| #define WLC_SET_UCANTDIV 100 |
| #define WLC_R_REG 101 |
| #define WLC_W_REG 102 |
| /* #define WLC_DIAG_LOOPBACK 103 old tray diag */ |
| /* #define WLC_RESET_D11CNTS 104 */ /* -> "reset_d11cnts" iovar */ |
| #define WLC_GET_MACMODE 105 |
| #define WLC_SET_MACMODE 106 |
| #define WLC_GET_MONITOR 107 |
| #define WLC_SET_MONITOR 108 |
| #define WLC_GET_GMODE 109 |
| #define WLC_SET_GMODE 110 |
| #define WLC_GET_LEGACY_ERP 111 |
| #define WLC_SET_LEGACY_ERP 112 |
| #define WLC_GET_RX_ANT 113 |
| #define WLC_GET_CURR_RATESET 114 /* current rateset */ |
| #define WLC_GET_SCANSUPPRESS 115 |
| #define WLC_SET_SCANSUPPRESS 116 |
| #define WLC_GET_AP 117 |
| #define WLC_SET_AP 118 |
| #define WLC_GET_EAP_RESTRICT 119 |
| #define WLC_SET_EAP_RESTRICT 120 |
| #define WLC_SCB_AUTHORIZE 121 |
| #define WLC_SCB_DEAUTHORIZE 122 |
| #define WLC_GET_WDSLIST 123 |
| #define WLC_SET_WDSLIST 124 |
| #define WLC_GET_ATIM 125 |
| #define WLC_SET_ATIM 126 |
| #define WLC_GET_RSSI 127 |
| #define WLC_GET_PHYANTDIV 128 |
| #define WLC_SET_PHYANTDIV 129 |
| #define WLC_AP_RX_ONLY 130 |
| #define WLC_GET_TX_PATH_PWR 131 |
| #define WLC_SET_TX_PATH_PWR 132 |
| #define WLC_GET_WSEC 133 |
| #define WLC_SET_WSEC 134 |
| #define WLC_GET_PHY_NOISE 135 |
| #define WLC_GET_BSS_INFO 136 |
| #define WLC_GET_PKTCNTS 137 |
| #define WLC_GET_LAZYWDS 138 |
| #define WLC_SET_LAZYWDS 139 |
| #define WLC_GET_BANDLIST 140 |
| |
| #define WLC_GET_BAND 141 |
| #define WLC_SET_BAND 142 |
| #define WLC_SCB_DEAUTHENTICATE 143 |
| #define WLC_GET_SHORTSLOT 144 |
| #define WLC_GET_SHORTSLOT_OVERRIDE 145 |
| #define WLC_SET_SHORTSLOT_OVERRIDE 146 |
| #define WLC_GET_SHORTSLOT_RESTRICT 147 |
| #define WLC_SET_SHORTSLOT_RESTRICT 148 |
| #define WLC_GET_GMODE_PROTECTION 149 |
| #define WLC_GET_GMODE_PROTECTION_OVERRIDE 150 |
| #define WLC_SET_GMODE_PROTECTION_OVERRIDE 151 |
| #define WLC_UPGRADE 152 |
| /* #define WLC_GET_MRATE 153 */ /* no longer supported */ |
| /* #define WLC_SET_MRATE 154 */ /* no longer supported */ |
| #define WLC_GET_IGNORE_BCNS 155 |
| #define WLC_SET_IGNORE_BCNS 156 |
| #define WLC_GET_SCB_TIMEOUT 157 |
| #define WLC_SET_SCB_TIMEOUT 158 |
| #define WLC_GET_ASSOCLIST 159 |
| #define WLC_GET_CLK 160 |
| #define WLC_SET_CLK 161 |
| #define WLC_GET_UP 162 |
| #define WLC_OUT 163 |
| #define WLC_GET_WPA_AUTH 164 |
| #define WLC_SET_WPA_AUTH 165 |
| #define WLC_GET_UCFLAGS 166 |
| #define WLC_SET_UCFLAGS 167 |
| #define WLC_GET_PWRIDX 168 |
| #define WLC_SET_PWRIDX 169 |
| #define WLC_GET_TSSI 170 |
| #define WLC_GET_SUP_RATESET_OVERRIDE 171 |
| #define WLC_SET_SUP_RATESET_OVERRIDE 172 |
| /* #define WLC_SET_FAST_TIMER 173 */ /* no longer supported */ |
| /* #define WLC_GET_FAST_TIMER 174 */ /* no longer supported */ |
| /* #define WLC_SET_SLOW_TIMER 175 */ /* no longer supported */ |
| /* #define WLC_GET_SLOW_TIMER 176 */ /* no longer supported */ |
| /* #define WLC_DUMP_PHYREGS 177 */ /* no longer supported */ |
| #define WLC_GET_PROTECTION_CONTROL 178 |
| #define WLC_SET_PROTECTION_CONTROL 179 |
| #define WLC_GET_PHYLIST 180 |
| #define WLC_ENCRYPT_STRENGTH 181 /* ndis only */ |
| #define WLC_DECRYPT_STATUS 182 /* ndis only */ |
| #define WLC_GET_KEY_SEQ 183 |
| #define WLC_GET_SCAN_CHANNEL_TIME 184 |
| #define WLC_SET_SCAN_CHANNEL_TIME 185 |
| #define WLC_GET_SCAN_UNASSOC_TIME 186 |
| #define WLC_SET_SCAN_UNASSOC_TIME 187 |
| #define WLC_GET_SCAN_HOME_TIME 188 |
| #define WLC_SET_SCAN_HOME_TIME 189 |
| #define WLC_GET_SCAN_NPROBES 190 |
| #define WLC_SET_SCAN_NPROBES 191 |
| #define WLC_GET_PRB_RESP_TIMEOUT 192 |
| #define WLC_SET_PRB_RESP_TIMEOUT 193 |
| #define WLC_GET_ATTEN 194 |
| #define WLC_SET_ATTEN 195 |
| #define WLC_GET_SHMEM 196 /* diag */ |
| #define WLC_SET_SHMEM 197 /* diag */ |
| /* #define WLC_GET_GMODE_PROTECTION_CTS 198 */ /* no longer supported */ |
| /* #define WLC_SET_GMODE_PROTECTION_CTS 199 */ /* no longer supported */ |
| #define WLC_SET_WSEC_TEST 200 |
| #define WLC_SCB_DEAUTHENTICATE_FOR_REASON 201 |
| #define WLC_TKIP_COUNTERMEASURES 202 |
| #define WLC_GET_PIOMODE 203 |
| #define WLC_SET_PIOMODE 204 |
| #define WLC_SET_ASSOC_PREFER 205 |
| #define WLC_GET_ASSOC_PREFER 206 |
| #define WLC_SET_ROAM_PREFER 207 |
| #define WLC_GET_ROAM_PREFER 208 |
| #define WLC_SET_LED 209 |
| #define WLC_GET_LED 210 |
| #define WLC_GET_INTERFERENCE_MODE 211 |
| #define WLC_SET_INTERFERENCE_MODE 212 |
| #define WLC_GET_CHANNEL_QA 213 |
| #define WLC_START_CHANNEL_QA 214 |
| #define WLC_GET_CHANNEL_SEL 215 |
| #define WLC_START_CHANNEL_SEL 216 |
| #define WLC_GET_VALID_CHANNELS 217 |
| #define WLC_GET_FAKEFRAG 218 |
| #define WLC_SET_FAKEFRAG 219 |
| #define WLC_GET_PWROUT_PERCENTAGE 220 |
| #define WLC_SET_PWROUT_PERCENTAGE 221 |
| #define WLC_SET_BAD_FRAME_PREEMPT 222 |
| #define WLC_GET_BAD_FRAME_PREEMPT 223 |
| #define WLC_SET_LEAP_LIST 224 |
| #define WLC_GET_LEAP_LIST 225 |
| #define WLC_GET_CWMIN 226 |
| #define WLC_SET_CWMIN 227 |
| #define WLC_GET_CWMAX 228 |
| #define WLC_SET_CWMAX 229 |
| #define WLC_GET_WET 230 |
| #define WLC_SET_WET 231 |
| #define WLC_GET_PUB 232 |
| /* #define WLC_SET_GLACIAL_TIMER 233 */ /* no longer supported */ |
| /* #define WLC_GET_GLACIAL_TIMER 234 */ /* no longer supported */ |
| #define WLC_GET_KEY_PRIMARY 235 |
| #define WLC_SET_KEY_PRIMARY 236 |
| |
| |
| /* #define WLC_DUMP_RADIOREGS 237 */ /* no longer supported */ |
| #define WLC_GET_ACI_ARGS 238 |
| #define WLC_SET_ACI_ARGS 239 |
| #define WLC_UNSET_CALLBACK 240 |
| #define WLC_SET_CALLBACK 241 |
| #define WLC_GET_RADAR 242 |
| #define WLC_SET_RADAR 243 |
| #define WLC_SET_SPECT_MANAGMENT 244 |
| #define WLC_GET_SPECT_MANAGMENT 245 |
| #define WLC_WDS_GET_REMOTE_HWADDR 246 /* handled in wl_linux.c/wl_vx.c */ |
| #define WLC_WDS_GET_WPA_SUP 247 |
| #define WLC_SET_CS_SCAN_TIMER 248 |
| #define WLC_GET_CS_SCAN_TIMER 249 |
| #define WLC_MEASURE_REQUEST 250 |
| #define WLC_INIT 251 |
| #define WLC_SEND_QUIET 252 |
| #define WLC_KEEPALIVE 253 |
| #define WLC_SEND_PWR_CONSTRAINT 254 |
| #define WLC_UPGRADE_STATUS 255 |
| #define WLC_CURRENT_PWR 256 |
| #define WLC_GET_SCAN_PASSIVE_TIME 257 |
| #define WLC_SET_SCAN_PASSIVE_TIME 258 |
| #define WLC_LEGACY_LINK_BEHAVIOR 259 |
| #define WLC_GET_CHANNELS_IN_COUNTRY 260 |
| #define WLC_GET_COUNTRY_LIST 261 |
| #define WLC_GET_VAR 262 /* get value of named variable */ |
| #define WLC_SET_VAR 263 /* set named variable to value */ |
| #define WLC_NVRAM_GET 264 /* deprecated */ |
| #define WLC_NVRAM_SET 265 |
| #define WLC_NVRAM_DUMP 266 |
| #define WLC_REBOOT 267 |
| #define WLC_SET_WSEC_PMK 268 |
| #define WLC_GET_AUTH_MODE 269 |
| #define WLC_SET_AUTH_MODE 270 |
| #define WLC_GET_WAKEENTRY 271 |
| #define WLC_SET_WAKEENTRY 272 |
| #define WLC_NDCONFIG_ITEM 273 /* currently handled in wl_oid.c */ |
| #define WLC_NVOTPW 274 |
| #define WLC_OTPW 275 |
| #define WLC_IOV_BLOCK_GET 276 |
| #define WLC_IOV_MODULES_GET 277 |
| #define WLC_SOFT_RESET 278 |
| #define WLC_GET_ALLOW_MODE 279 |
| #define WLC_SET_ALLOW_MODE 280 |
| #define WLC_GET_DESIRED_BSSID 281 |
| #define WLC_SET_DESIRED_BSSID 282 |
| #define WLC_DISASSOC_MYAP 283 |
| #define WLC_GET_NBANDS 284 /* for Dongle EXT_STA support */ |
| #define WLC_GET_BANDSTATES 285 /* for Dongle EXT_STA support */ |
| #define WLC_GET_WLC_BSS_INFO 286 /* for Dongle EXT_STA support */ |
| #define WLC_GET_ASSOC_INFO 287 /* for Dongle EXT_STA support */ |
| #define WLC_GET_OID_PHY 288 /* for Dongle EXT_STA support */ |
| #define WLC_SET_OID_PHY 289 /* for Dongle EXT_STA support */ |
| #define WLC_SET_ASSOC_TIME 290 /* for Dongle EXT_STA support */ |
| #define WLC_GET_DESIRED_SSID 291 /* for Dongle EXT_STA support */ |
| #define WLC_GET_CHANSPEC 292 /* for Dongle EXT_STA support */ |
| #define WLC_GET_ASSOC_STATE 293 /* for Dongle EXT_STA support */ |
| #define WLC_SET_PHY_STATE 294 /* for Dongle EXT_STA support */ |
| #define WLC_GET_SCAN_PENDING 295 /* for Dongle EXT_STA support */ |
| #define WLC_GET_SCANREQ_PENDING 296 /* for Dongle EXT_STA support */ |
| #define WLC_GET_PREV_ROAM_REASON 297 /* for Dongle EXT_STA support */ |
| #define WLC_SET_PREV_ROAM_REASON 298 /* for Dongle EXT_STA support */ |
| #define WLC_GET_BANDSTATES_PI 299 /* for Dongle EXT_STA support */ |
| #define WLC_GET_PHY_STATE 300 /* for Dongle EXT_STA support */ |
| #define WLC_GET_BSS_WPA_RSN 301 /* for Dongle EXT_STA support */ |
| #define WLC_GET_BSS_WPA2_RSN 302 /* for Dongle EXT_STA support */ |
| #define WLC_GET_BSS_BCN_TS 303 /* for Dongle EXT_STA support */ |
| #define WLC_GET_INT_DISASSOC 304 /* for Dongle EXT_STA support */ |
| #define WLC_SET_NUM_PEERS 305 /* for Dongle EXT_STA support */ |
| #define WLC_GET_NUM_BSS 306 /* for Dongle EXT_STA support */ |
| #define WLC_PHY_SAMPLE_COLLECT 307 /* phy sample collect mode */ |
| /* #define WLC_UM_PRIV 308 */ /* Deprecated: usermode driver */ |
| #define WLC_GET_CMD 309 |
| /* #define WLC_LAST 310 */ /* Never used - can be reused */ |
| #define WLC_SET_INTERFERENCE_OVERRIDE_MODE 311 /* set inter mode override */ |
| #define WLC_GET_INTERFERENCE_OVERRIDE_MODE 312 /* get inter mode override */ |
| /* #define WLC_GET_WAI_RESTRICT 313 */ |
| /* #define WLC_SET_WAI_RESTRICT 314 */ |
| /* #define WLC_SET_WAI_REKEY 315 */ |
| #define WLC_SET_NAT_CONFIG 316 /* for configuring NAT filter driver */ |
| #define WLC_GET_NAT_STATE 317 |
| #define WLC_GET_TXBF_RATESET 318 |
| #define WLC_SET_TXBF_RATESET 319 |
| #define WLC_SCAN_CQ 320 |
| #define WLC_GET_RSSI_QDB 321 /* qdB portion of the RSSI */ |
| #define WLC_DUMP_RATESET 322 |
| #define WLC_ECHO 323 |
| #define WLC_LAST 324 |
| #ifndef EPICTRL_COOKIE |
| #define EPICTRL_COOKIE 0xABADCEDE |
| #endif |
| |
| /* vx wlc ioctl's offset */ |
| #define CMN_IOCTL_OFF 0x180 |
| |
| /* |
| * custom OID support |
| * |
| * 0xFF - implementation specific OID |
| * 0xE4 - first byte of Broadcom PCI vendor ID |
| * 0x14 - second byte of Broadcom PCI vendor ID |
| * 0xXX - the custom OID number |
| */ |
| |
| /* begin 0x1f values beyond the start of the ET driver range. */ |
| #define WL_OID_BASE 0xFFE41420 |
| |
| /* NDIS overrides */ |
| #define OID_WL_GETINSTANCE (WL_OID_BASE + WLC_GET_INSTANCE) |
| #define OID_WL_GET_FORCELINK (WL_OID_BASE + WLC_GET_FORCELINK) |
| #define OID_WL_SET_FORCELINK (WL_OID_BASE + WLC_SET_FORCELINK) |
| #define OID_WL_ENCRYPT_STRENGTH (WL_OID_BASE + WLC_ENCRYPT_STRENGTH) |
| #define OID_WL_DECRYPT_STATUS (WL_OID_BASE + WLC_DECRYPT_STATUS) |
| #define OID_LEGACY_LINK_BEHAVIOR (WL_OID_BASE + WLC_LEGACY_LINK_BEHAVIOR) |
| #define OID_WL_NDCONFIG_ITEM (WL_OID_BASE + WLC_NDCONFIG_ITEM) |
| |
| /* EXT_STA Dongle suuport */ |
| #define OID_STA_CHANSPEC (WL_OID_BASE + WLC_GET_CHANSPEC) |
| #define OID_STA_NBANDS (WL_OID_BASE + WLC_GET_NBANDS) |
| #define OID_STA_GET_PHY (WL_OID_BASE + WLC_GET_OID_PHY) |
| #define OID_STA_SET_PHY (WL_OID_BASE + WLC_SET_OID_PHY) |
| #define OID_STA_ASSOC_TIME (WL_OID_BASE + WLC_SET_ASSOC_TIME) |
| #define OID_STA_DESIRED_SSID (WL_OID_BASE + WLC_GET_DESIRED_SSID) |
| #define OID_STA_SET_PHY_STATE (WL_OID_BASE + WLC_SET_PHY_STATE) |
| #define OID_STA_SCAN_PENDING (WL_OID_BASE + WLC_GET_SCAN_PENDING) |
| #define OID_STA_SCANREQ_PENDING (WL_OID_BASE + WLC_GET_SCANREQ_PENDING) |
| #define OID_STA_GET_ROAM_REASON (WL_OID_BASE + WLC_GET_PREV_ROAM_REASON) |
| #define OID_STA_SET_ROAM_REASON (WL_OID_BASE + WLC_SET_PREV_ROAM_REASON) |
| #define OID_STA_GET_PHY_STATE (WL_OID_BASE + WLC_GET_PHY_STATE) |
| #define OID_STA_INT_DISASSOC (WL_OID_BASE + WLC_GET_INT_DISASSOC) |
| #define OID_STA_SET_NUM_PEERS (WL_OID_BASE + WLC_SET_NUM_PEERS) |
| #define OID_STA_GET_NUM_BSS (WL_OID_BASE + WLC_GET_NUM_BSS) |
| |
| /* NAT filter driver support */ |
| #define OID_NAT_SET_CONFIG (WL_OID_BASE + WLC_SET_NAT_CONFIG) |
| #define OID_NAT_GET_STATE (WL_OID_BASE + WLC_GET_NAT_STATE) |
| |
| #define WL_DECRYPT_STATUS_SUCCESS 1 |
| #define WL_DECRYPT_STATUS_FAILURE 2 |
| #define WL_DECRYPT_STATUS_UNKNOWN 3 |
| |
| /* allows user-mode app to poll the status of USB image upgrade */ |
| #define WLC_UPGRADE_SUCCESS 0 |
| #define WLC_UPGRADE_PENDING 1 |
| |
| /* WLC_GET_AUTH, WLC_SET_AUTH values */ |
| #define WL_AUTH_OPEN_SYSTEM 0 /* d11 open authentication */ |
| #define WL_AUTH_SHARED_KEY 1 /* d11 shared authentication */ |
| #define WL_AUTH_OPEN_SHARED 2 /* try open, then shared if open failed w/rc 13 */ |
| |
| /* a large TX Power as an init value to factor out of MIN() calculations, |
| * keep low enough to fit in an int8, units are .25 dBm |
| */ |
| #define WLC_TXPWR_MAX (127) /* ~32 dBm = 1,500 mW */ |
| |
| /* "diag" iovar argument and error code */ |
| #define WL_DIAG_INTERRUPT 1 /* d11 loopback interrupt test */ |
| #define WL_DIAG_LOOPBACK 2 /* d11 loopback data test */ |
| #define WL_DIAG_MEMORY 3 /* d11 memory test */ |
| #define WL_DIAG_LED 4 /* LED test */ |
| #define WL_DIAG_REG 5 /* d11/phy register test */ |
| #define WL_DIAG_SROM 6 /* srom read/crc test */ |
| #define WL_DIAG_DMA 7 /* DMA test */ |
| #define WL_DIAG_LOOPBACK_EXT 8 /* enhenced d11 loopback data test */ |
| |
| #define WL_DIAGERR_SUCCESS 0 |
| #define WL_DIAGERR_FAIL_TO_RUN 1 /* unable to run requested diag */ |
| #define WL_DIAGERR_NOT_SUPPORTED 2 /* diag requested is not supported */ |
| #define WL_DIAGERR_INTERRUPT_FAIL 3 /* loopback interrupt test failed */ |
| #define WL_DIAGERR_LOOPBACK_FAIL 4 /* loopback data test failed */ |
| #define WL_DIAGERR_SROM_FAIL 5 /* srom read failed */ |
| #define WL_DIAGERR_SROM_BADCRC 6 /* srom crc failed */ |
| #define WL_DIAGERR_REG_FAIL 7 /* d11/phy register test failed */ |
| #define WL_DIAGERR_MEMORY_FAIL 8 /* d11 memory test failed */ |
| #define WL_DIAGERR_NOMEM 9 /* diag test failed due to no memory */ |
| #define WL_DIAGERR_DMA_FAIL 10 /* DMA test failed */ |
| |
| #define WL_DIAGERR_MEMORY_TIMEOUT 11 /* d11 memory test didn't finish in time */ |
| #define WL_DIAGERR_MEMORY_BADPATTERN 12 /* d11 memory test result in bad pattern */ |
| |
| /* band types */ |
| #define WLC_BAND_AUTO 0 /* auto-select */ |
| #define WLC_BAND_5G 1 /* 5 Ghz */ |
| #define WLC_BAND_2G 2 /* 2.4 Ghz */ |
| #define WLC_BAND_ALL 3 /* all bands */ |
| #define WLC_BAND_INVALID -1 /* Invalid band */ |
| |
| /* band range returned by band_range iovar */ |
| #define WL_CHAN_FREQ_RANGE_2G 0 |
| #define WL_CHAN_FREQ_RANGE_5GL 1 |
| #define WL_CHAN_FREQ_RANGE_5GM 2 |
| #define WL_CHAN_FREQ_RANGE_5GH 3 |
| |
| #define WL_CHAN_FREQ_RANGE_5GLL_5BAND 4 |
| #define WL_CHAN_FREQ_RANGE_5GLH_5BAND 5 |
| #define WL_CHAN_FREQ_RANGE_5GML_5BAND 6 |
| #define WL_CHAN_FREQ_RANGE_5GMH_5BAND 7 |
| #define WL_CHAN_FREQ_RANGE_5GH_5BAND 8 |
| |
| #define WL_CHAN_FREQ_RANGE_5G_BAND0 1 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND1 2 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND2 3 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND3 4 |
| #define WL_CHAN_FREQ_RANGE_5G_4BAND 5 |
| |
| /* SROM12 */ |
| #define WL_CHAN_FREQ_RANGE_5G_BAND4 5 |
| #define WL_CHAN_FREQ_RANGE_2G_40 6 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND0_40 7 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND1_40 8 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND2_40 9 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND3_40 10 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND4_40 11 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND0_80 12 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND1_80 13 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND2_80 14 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND3_80 15 |
| #define WL_CHAN_FREQ_RANGE_5G_BAND4_80 16 |
| |
| #define WL_CHAN_FREQ_RANGE_5G_5BAND 18 |
| #define WL_CHAN_FREQ_RANGE_5G_5BAND_40 19 |
| #define WL_CHAN_FREQ_RANGE_5G_5BAND_80 20 |
| |
| #define WLC_MACMODE_DISABLED 0 /* MAC list disabled */ |
| #define WLC_MACMODE_DENY 1 /* Deny specified (i.e. allow unspecified) */ |
| #define WLC_MACMODE_ALLOW 2 /* Allow specified (i.e. deny unspecified) */ |
| |
| /* |
| * 54g modes (basic bits may still be overridden) |
| * |
| * GMODE_LEGACY_B Rateset: 1b, 2b, 5.5, 11 |
| * Preamble: Long |
| * Shortslot: Off |
| * GMODE_AUTO Rateset: 1b, 2b, 5.5b, 11b, 18, 24, 36, 54 |
| * Extended Rateset: 6, 9, 12, 48 |
| * Preamble: Long |
| * Shortslot: Auto |
| * GMODE_ONLY Rateset: 1b, 2b, 5.5b, 11b, 18, 24b, 36, 54 |
| * Extended Rateset: 6b, 9, 12b, 48 |
| * Preamble: Short required |
| * Shortslot: Auto |
| * GMODE_B_DEFERRED Rateset: 1b, 2b, 5.5b, 11b, 18, 24, 36, 54 |
| * Extended Rateset: 6, 9, 12, 48 |
| * Preamble: Long |
| * Shortslot: On |
| * GMODE_PERFORMANCE Rateset: 1b, 2b, 5.5b, 6b, 9, 11b, 12b, 18, 24b, 36, 48, 54 |
| * Preamble: Short required |
| * Shortslot: On and required |
| * GMODE_LRS Rateset: 1b, 2b, 5.5b, 11b |
| * Extended Rateset: 6, 9, 12, 18, 24, 36, 48, 54 |
| * Preamble: Long |
| * Shortslot: Auto |
| */ |
| #define GMODE_LEGACY_B 0 |
| #define GMODE_AUTO 1 |
| #define GMODE_ONLY 2 |
| #define GMODE_B_DEFERRED 3 |
| #define GMODE_PERFORMANCE 4 |
| #define GMODE_LRS 5 |
| #define GMODE_MAX 6 |
| |
| /* values for PLCPHdr_override */ |
| #define WLC_PLCP_AUTO -1 |
| #define WLC_PLCP_SHORT 0 |
| #define WLC_PLCP_LONG 1 |
| |
| /* values for g_protection_override and n_protection_override */ |
| #define WLC_PROTECTION_AUTO -1 |
| #define WLC_PROTECTION_OFF 0 |
| #define WLC_PROTECTION_ON 1 |
| #define WLC_PROTECTION_MMHDR_ONLY 2 |
| #define WLC_PROTECTION_CTS_ONLY 3 |
| |
| /* values for g_protection_control and n_protection_control */ |
| #define WLC_PROTECTION_CTL_OFF 0 |
| #define WLC_PROTECTION_CTL_LOCAL 1 |
| #define WLC_PROTECTION_CTL_OVERLAP 2 |
| |
| /* values for n_protection */ |
| #define WLC_N_PROTECTION_OFF 0 |
| #define WLC_N_PROTECTION_OPTIONAL 1 |
| #define WLC_N_PROTECTION_20IN40 2 |
| #define WLC_N_PROTECTION_MIXEDMODE 3 |
| |
| /* values for n_preamble_type */ |
| #define WLC_N_PREAMBLE_MIXEDMODE 0 |
| #define WLC_N_PREAMBLE_GF 1 |
| #define WLC_N_PREAMBLE_GF_BRCM 2 |
| |
| /* values for band specific 40MHz capabilities (deprecated) */ |
| #define WLC_N_BW_20ALL 0 |
| #define WLC_N_BW_40ALL 1 |
| #define WLC_N_BW_20IN2G_40IN5G 2 |
| |
| #define WLC_BW_20MHZ_BIT (1<<0) |
| #define WLC_BW_40MHZ_BIT (1<<1) |
| #define WLC_BW_80MHZ_BIT (1<<2) |
| #define WLC_BW_160MHZ_BIT (1<<3) |
| #define WLC_BW_10MHZ_BIT (1<<4) |
| #define WLC_BW_5MHZ_BIT (1<<5) |
| #define WLC_BW_2P5MHZ_BIT (1<<6) |
| /* Bandwidth capabilities */ |
| #define WLC_BW_CAP_20MHZ (WLC_BW_20MHZ_BIT) |
| #define WLC_BW_CAP_40MHZ (WLC_BW_40MHZ_BIT|WLC_BW_20MHZ_BIT) |
| #define WLC_BW_CAP_80MHZ (WLC_BW_80MHZ_BIT|WLC_BW_40MHZ_BIT|WLC_BW_20MHZ_BIT) |
| #define WLC_BW_CAP_160MHZ (WLC_BW_160MHZ_BIT|WLC_BW_80MHZ_BIT| \ |
| WLC_BW_40MHZ_BIT|WLC_BW_20MHZ_BIT) |
| #define WLC_BW_CAP_2P5MHZ (WLC_BW_2P5MHZ_BIT) |
| #define WLC_BW_CAP_5MHZ (WLC_BW_5MHZ_BIT) |
| #define WLC_BW_CAP_10MHZ (WLC_BW_10MHZ_BIT) |
| #define WLC_BW_CAP_UNRESTRICTED 0xFF |
| |
| #define WL_BW_CAP_20MHZ(bw_cap) (((bw_cap) & WLC_BW_20MHZ_BIT) ? TRUE : FALSE) |
| #define WL_BW_CAP_40MHZ(bw_cap) (((bw_cap) & WLC_BW_40MHZ_BIT) ? TRUE : FALSE) |
| #define WL_BW_CAP_80MHZ(bw_cap) (((bw_cap) & WLC_BW_80MHZ_BIT) ? TRUE : FALSE) |
| #define WL_BW_CAP_160MHZ(bw_cap)(((bw_cap) & WLC_BW_160MHZ_BIT) ? TRUE : FALSE) |
| #define WL_BW_CAP_2P5MHZ(bw_cap)(((bw_cap) & WLC_BW_2P5MHZ_BIT) ? TRUE : FALSE) |
| #define WL_BW_CAP_5MHZ(bw_cap) (((bw_cap) & WLC_BW_5MHZ_BIT) ? TRUE : FALSE) |
| #define WL_BW_CAP_10MHZ(bw_cap) (((bw_cap) & WLC_BW_10MHZ_BIT) ? TRUE : FALSE) |
| /* values to force tx/rx chain */ |
| #define WLC_N_TXRX_CHAIN0 0 |
| #define WLC_N_TXRX_CHAIN1 1 |
| |
| /* bitflags for SGI support (sgi_rx iovar) */ |
| #define WLC_N_SGI_20 0x01 |
| #define WLC_N_SGI_40 0x02 |
| #define WLC_VHT_SGI_80 0x04 |
| #define WLC_VHT_SGI_160 0x08 |
| |
| /* when sgi_tx==WLC_SGI_ALL, bypass rate selection, enable sgi for all mcs */ |
| #define WLC_SGI_ALL 0x02 |
| |
| #define LISTEN_INTERVAL 10 |
| /* interference mitigation options */ |
| #define INTERFERE_OVRRIDE_OFF -1 /* interference override off */ |
| #define INTERFERE_NONE 0 /* off */ |
| #define NON_WLAN 1 /* foreign/non 802.11 interference, no auto detect */ |
| #define WLAN_MANUAL 2 /* ACI: no auto detection */ |
| #define WLAN_AUTO 3 /* ACI: auto detect */ |
| #define WLAN_AUTO_W_NOISE 4 /* ACI: auto - detect and non 802.11 interference */ |
| #define AUTO_ACTIVE (1 << 7) /* Auto is currently active */ |
| |
| /* interfernece mode bit-masks (ACPHY) */ |
| #define ACPHY_ACI_GLITCHBASED_DESENSE 1 /* bit 0 */ |
| #define ACPHY_ACI_HWACI_PKTGAINLMT 2 /* bit 1 */ |
| #define ACPHY_ACI_W2NB_PKTGAINLMT 4 /* bit 2 */ |
| #define ACPHY_ACI_PREEMPTION 8 /* bit 3 */ |
| #define ACPHY_HWACI_MITIGATION 16 /* bit 4 */ |
| #define ACPHY_LPD_PREEMPTION 32 /* bit 5 */ |
| #define ACPHY_HWOBSS_MITIGATION 64 /* bit 6 */ |
| #define ACPHY_ACI_MAX_MODE 127 |
| |
| /* AP environment */ |
| #define AP_ENV_DETECT_NOT_USED 0 /* We aren't using AP environment detection */ |
| #define AP_ENV_DENSE 1 /* "Corporate" or other AP dense environment */ |
| #define AP_ENV_SPARSE 2 /* "Home" or other sparse environment */ |
| #define AP_ENV_INDETERMINATE 3 /* AP environment hasn't been identified */ |
| |
| #define TRIGGER_NOW 0 |
| #define TRIGGER_CRS 0x01 |
| #define TRIGGER_CRSDEASSERT 0x02 |
| #define TRIGGER_GOODFCS 0x04 |
| #define TRIGGER_BADFCS 0x08 |
| #define TRIGGER_BADPLCP 0x10 |
| #define TRIGGER_CRSGLITCH 0x20 |
| |
| #define WL_SAMPLEDATA_HEADER_TYPE 1 |
| #define WL_SAMPLEDATA_HEADER_SIZE 80 /* sample collect header size (bytes) */ |
| #define WL_SAMPLEDATA_TYPE 2 |
| #define WL_SAMPLEDATA_SEQ 0xff /* sequence # */ |
| #define WL_SAMPLEDATA_MORE_DATA 0x100 /* more data mask */ |
| |
| /* WL_OTA START */ |
| #define WL_OTA_ARG_PARSE_BLK_SIZE 1200 |
| #define WL_OTA_TEST_MAX_NUM_RATE 30 |
| #define WL_OTA_TEST_MAX_NUM_SEQ 100 |
| #define WL_OTA_TEST_MAX_NUM_RSSI 85 |
| #define WL_THRESHOLD_LO_BAND 70 /* range from 5250MHz - 5350MHz */ |
| |
| /* radar iovar SET defines */ |
| #define WL_RADAR_DETECTOR_OFF 0 /* radar detector off */ |
| #define WL_RADAR_DETECTOR_ON 1 /* radar detector on */ |
| #define WL_RADAR_SIMULATED 2 /* force radar detector to declare |
| * detection once |
| */ |
| #define WL_RADAR_SIMULATED_SC 3 /* force radar detector to declare |
| * detection once on scan core |
| * if available and active |
| */ |
| #define WL_RSSI_ANT_VERSION 1 /* current version of wl_rssi_ant_t */ |
| #define WL_ANT_RX_MAX 2 /* max 2 receive antennas */ |
| #define WL_ANT_HT_RX_MAX 4 /* max 4 receive antennas/cores */ |
| #define WL_ANT_IDX_1 0 /* antenna index 1 */ |
| #define WL_ANT_IDX_2 1 /* antenna index 2 */ |
| |
| #ifndef WL_RSSI_ANT_MAX |
| #define WL_RSSI_ANT_MAX 4 /* max possible rx antennas */ |
| #elif WL_RSSI_ANT_MAX != 4 |
| #error "WL_RSSI_ANT_MAX does not match" |
| #endif |
| |
| /* dfs_status iovar-related defines */ |
| |
| /* cac - channel availability check, |
| * ism - in-service monitoring |
| * csa - channel switching announcement |
| */ |
| |
| /* cac state values */ |
| #define WL_DFS_CACSTATE_IDLE 0 /* state for operating in non-radar channel */ |
| #define WL_DFS_CACSTATE_PREISM_CAC 1 /* CAC in progress */ |
| #define WL_DFS_CACSTATE_ISM 2 /* ISM in progress */ |
| #define WL_DFS_CACSTATE_CSA 3 /* csa */ |
| #define WL_DFS_CACSTATE_POSTISM_CAC 4 /* ISM CAC */ |
| #define WL_DFS_CACSTATE_PREISM_OOC 5 /* PREISM OOC */ |
| #define WL_DFS_CACSTATE_POSTISM_OOC 6 /* POSTISM OOC */ |
| #define WL_DFS_CACSTATES 7 /* this many states exist */ |
| |
| /* Defines used with channel_bandwidth for curpower */ |
| #define WL_BW_20MHZ 0 |
| #define WL_BW_40MHZ 1 |
| #define WL_BW_80MHZ 2 |
| #define WL_BW_160MHZ 3 |
| #define WL_BW_8080MHZ 4 |
| #define WL_BW_2P5MHZ 5 |
| #define WL_BW_5MHZ 6 |
| #define WL_BW_10MHZ 7 |
| |
| /* tx_power_t.flags bits */ |
| #define WL_TX_POWER_F_ENABLED 1 |
| #define WL_TX_POWER_F_HW 2 |
| #define WL_TX_POWER_F_MIMO 4 |
| #define WL_TX_POWER_F_SISO 8 |
| #define WL_TX_POWER_F_HT 0x10 |
| #define WL_TX_POWER_F_VHT 0x20 |
| #define WL_TX_POWER_F_OPENLOOP 0x40 |
| #define WL_TX_POWER_F_PROP11NRATES 0x80 |
| #define WL_TX_POWER_F_UNIT_QDBM 0x100 |
| /* Message levels */ |
| #define WL_ERROR_VAL 0x00000001 |
| #define WL_TRACE_VAL 0x00000002 |
| #define WL_PRHDRS_VAL 0x00000004 |
| #define WL_PRPKT_VAL 0x00000008 |
| #define WL_INFORM_VAL 0x00000010 |
| #define WL_TMP_VAL 0x00000020 |
| #define WL_OID_VAL 0x00000040 |
| #define WL_RATE_VAL 0x00000080 |
| #define WL_ASSOC_VAL 0x00000100 |
| #define WL_PRUSR_VAL 0x00000200 |
| #define WL_PS_VAL 0x00000400 |
| #define WL_TXPWR_VAL 0x00000000 /* retired in TOT on 6/10/2009 */ |
| #define WL_MODE_SWITCH_VAL 0x00000800 /* Using retired TXPWR val */ |
| #define WL_PORT_VAL 0x00001000 |
| #define WL_DUAL_VAL 0x00002000 |
| #define WL_WSEC_VAL 0x00004000 |
| #define WL_WSEC_DUMP_VAL 0x00008000 |
| #define WL_LOG_VAL 0x00010000 |
| #define WL_NRSSI_VAL 0x00000000 /* retired in TOT on 6/10/2009 */ |
| #define WL_BCNTRIM_VAL 0x00020000 /* Using retired NRSSI VAL */ |
| #define WL_LOFT_VAL 0x00000000 /* retired in TOT on 6/10/2009 */ |
| #define WL_PFN_VAL 0x00040000 /* Using retired LOFT_VAL */ |
| #define WL_REGULATORY_VAL 0x00080000 |
| #define WL_CSA_VAL 0x00080000 /* Reusing REGULATORY_VAL due to lackof bits */ |
| #define WL_TAF_VAL 0x00100000 |
| #define WL_RADAR_VAL 0x00000000 /* retired in TOT on 6/10/2009 */ |
| #define WL_WDI_VAL 0x00200000 /* Using retired WL_RADAR_VAL VAL */ |
| #define WL_MPC_VAL 0x00400000 |
| #define WL_APSTA_VAL 0x00800000 |
| #define WL_DFS_VAL 0x01000000 |
| #define WL_BA_VAL 0x00000000 /* retired in TOT on 6/14/2010 */ |
| #define WL_MUMIMO_VAL 0x02000000 /* Using retired WL_BA_VAL */ |
| #define WL_ACI_VAL 0x04000000 |
| #define WL_PRMAC_VAL 0x04000000 |
| #define WL_MBSS_VAL 0x04000000 |
| #define WL_CAC_VAL 0x08000000 |
| #define WL_AMSDU_VAL 0x10000000 |
| #define WL_AMPDU_VAL 0x20000000 |
| #define WL_FFPLD_VAL 0x40000000 |
| #define WL_ROAM_EXP_VAL 0x80000000 |
| |
| /* wl_msg_level is full. For new bits take the next one and AND with |
| * wl_msg_level2 in wl_dbg.h |
| */ |
| #define WL_DPT_VAL 0x00000001 |
| /* re-using WL_DPT_VAL */ |
| /* re-using WL_MESH_VAL */ |
| #define WL_NATOE_VAL 0x00000001 |
| #define WL_MESH_VAL 0x00000001 |
| #define WL_SCAN_VAL 0x00000002 |
| #define WL_WOWL_VAL 0x00000004 |
| #define WL_COEX_VAL 0x00000008 |
| #define WL_RTDC_VAL 0x00000010 |
| #define WL_PROTO_VAL 0x00000020 |
| #define WL_BTA_VAL 0x00000040 |
| #define WL_CHANINT_VAL 0x00000080 |
| #define WL_WMF_VAL 0x00000100 |
| #define WL_P2P_VAL 0x00000200 |
| #define WL_ITFR_VAL 0x00000400 |
| #define WL_MCHAN_VAL 0x00000800 |
| #define WL_TDLS_VAL 0x00001000 |
| #define WL_MCNX_VAL 0x00002000 |
| #define WL_PROT_VAL 0x00004000 |
| #define WL_PSTA_VAL 0x00008000 |
| #define WL_TSO_VAL 0x00010000 |
| #define WL_TRF_MGMT_VAL 0x00020000 |
| #define WL_LPC_VAL 0x00040000 |
| #define WL_L2FILTER_VAL 0x00080000 |
| #define WL_TXBF_VAL 0x00100000 |
| #define WL_P2PO_VAL 0x00200000 |
| #define WL_TBTT_VAL 0x00400000 |
| #define WL_FBT_VAL 0x00800000 |
| #define WL_RRM_VAL 0x00800000 /* reuse */ |
| #define WL_MQ_VAL 0x01000000 |
| |
| /* This level is currently used in Phoenix2 only */ |
| #define WL_SRSCAN_VAL 0x02000000 |
| |
| #define WL_WNM_VAL 0x04000000 |
| /* re-using WL_WNM_VAL for MBO */ |
| #define WL_MBO_VAL 0x04000000 |
| #define WL_PWRSEL_VAL 0x10000000 |
| #define WL_NET_DETECT_VAL 0x20000000 |
| #define WL_PCIE_VAL 0x40000000 |
| #define WL_PMDUR_VAL 0x80000000 |
| |
| |
| /* use top-bit for WL_TIME_STAMP_VAL because this is a modifier |
| * rather than a message-type of its own |
| */ |
| #define WL_TIMESTAMP_VAL 0x80000000 |
| |
| /* max # of leds supported by GPIO (gpio pin# == led index#) */ |
| #define WL_LED_NUMGPIO 32 /* gpio 0-31 */ |
| |
| /* led per-pin behaviors */ |
| #define WL_LED_OFF 0 /* always off */ |
| #define WL_LED_ON 1 /* always on */ |
| #define WL_LED_ACTIVITY 2 /* activity */ |
| #define WL_LED_RADIO 3 /* radio enabled */ |
| #define WL_LED_ARADIO 4 /* 5 Ghz radio enabled */ |
| #define WL_LED_BRADIO 5 /* 2.4Ghz radio enabled */ |
| #define WL_LED_BGMODE 6 /* on if gmode, off if bmode */ |
| #define WL_LED_WI1 7 |
| #define WL_LED_WI2 8 |
| #define WL_LED_WI3 9 |
| #define WL_LED_ASSOC 10 /* associated state indicator */ |
| #define WL_LED_INACTIVE 11 /* null behavior (clears default behavior) */ |
| #define WL_LED_ASSOCACT 12 /* on when associated; blink fast for activity */ |
| #define WL_LED_WI4 13 |
| #define WL_LED_WI5 14 |
| #define WL_LED_BLINKSLOW 15 /* blink slow */ |
| #define WL_LED_BLINKMED 16 /* blink med */ |
| #define WL_LED_BLINKFAST 17 /* blink fast */ |
| #define WL_LED_BLINKCUSTOM 18 /* blink custom */ |
| #define WL_LED_BLINKPERIODIC 19 /* blink periodic (custom 1000ms / off 400ms) */ |
| #define WL_LED_ASSOC_WITH_SEC 20 /* when connected with security */ |
| /* keep on for 300 sec */ |
| #define WL_LED_START_OFF 21 /* off upon boot, could be turned on later */ |
| #define WL_LED_WI6 22 |
| #define WL_LED_WI7 23 |
| #define WL_LED_WI8 24 |
| #define WL_LED_NUMBEHAVIOR 25 |
| |
| /* led behavior numeric value format */ |
| #define WL_LED_BEH_MASK 0x3f /* behavior mask */ |
| #define WL_LED_PMU_OVERRIDE 0x40 /* need to set PMU Override bit for the GPIO */ |
| #define WL_LED_AL_MASK 0x80 /* activelow (polarity) bit */ |
| |
| /* number of bytes needed to define a proper bit mask for MAC event reporting */ |
| #define BCMIO_ROUNDUP(x, y) ((((x) + ((y) - 1)) / (y)) * (y)) |
| #define BCMIO_NBBY 8 |
| #define WL_EVENTING_MASK_LEN 16 |
| |
| #define WL_EVENTING_MASK_EXT_LEN \ |
| MAX(WL_EVENTING_MASK_LEN, (ROUNDUP(WLC_E_LAST, NBBY)/NBBY)) |
| |
| /* join preference types */ |
| #define WL_JOIN_PREF_RSSI 1 /* by RSSI */ |
| #define WL_JOIN_PREF_WPA 2 /* by akm and ciphers */ |
| #define WL_JOIN_PREF_BAND 3 /* by 802.11 band */ |
| #define WL_JOIN_PREF_RSSI_DELTA 4 /* by 802.11 band only if RSSI delta condition matches */ |
| #define WL_JOIN_PREF_TRANS_PREF 5 /* defined by requesting AP */ |
| |
| /* band preference */ |
| #define WLJP_BAND_ASSOC_PREF 255 /* use what WLC_SET_ASSOC_PREFER ioctl specifies */ |
| |
| /* any multicast cipher suite */ |
| #define WL_WPA_ACP_MCS_ANY "\x00\x00\x00\x00" |
| |
| /* 802.11h measurement types */ |
| #define WLC_MEASURE_TPC 1 |
| #define WLC_MEASURE_CHANNEL_BASIC 2 |
| #define WLC_MEASURE_CHANNEL_CCA 3 |
| #define WLC_MEASURE_CHANNEL_RPI 4 |
| |
| /* regulatory enforcement levels */ |
| #define SPECT_MNGMT_OFF 0 /* both 11h and 11d disabled */ |
| #define SPECT_MNGMT_LOOSE_11H 1 /* allow non-11h APs in scan lists */ |
| #define SPECT_MNGMT_STRICT_11H 2 /* prune out non-11h APs from scan list */ |
| #define SPECT_MNGMT_STRICT_11D 3 /* switch to 802.11D mode */ |
| /* SPECT_MNGMT_LOOSE_11H_D - same as SPECT_MNGMT_LOOSE with the exception that Country IE |
| * adoption is done regardless of capability spectrum_management |
| */ |
| #define SPECT_MNGMT_LOOSE_11H_D 4 /* operation defined above */ |
| |
| /* bit position in per_chan_info; these depend on current country/regulatory domain */ |
| #define WL_CHAN_VALID_HW (1 << 0) /* valid with current HW */ |
| #define WL_CHAN_VALID_SW (1 << 1) /* valid with current country setting */ |
| #define WL_CHAN_BAND_5G (1 << 2) /* 5GHz-band channel */ |
| #define WL_CHAN_RADAR (1 << 3) /* radar sensitive channel */ |
| #define WL_CHAN_INACTIVE (1 << 4) /* temporarily inactive due to radar */ |
| #define WL_CHAN_PASSIVE (1 << 5) /* channel is in passive mode */ |
| #define WL_CHAN_RESTRICTED (1 << 6) /* restricted use channel */ |
| #define WL_CHAN_RADAR_EU_WEATHER (1 << 7) /* EU Radar weather channel. Implies an |
| * EU Radar channel. |
| */ |
| /* following definition is for precommit; will be removed once wl, acsd switch to the new def */ |
| #define WL_CHAN_WEATHER_RADAR WL_CHAN_RADAR_EU_WEATHER |
| |
| /* BTC mode used by "btc_mode" iovar */ |
| #define WL_BTC_DISABLE 0 /* disable BT coexistence */ |
| #define WL_BTC_FULLTDM 1 /* full TDM COEX */ |
| #define WL_BTC_ENABLE 1 /* full TDM COEX to maintain backward compatiblity */ |
| #define WL_BTC_PREMPT 2 /* full TDM COEX with preemption */ |
| #define WL_BTC_LITE 3 /* light weight coex for large isolation platform */ |
| #define WL_BTC_PARALLEL 4 /* BT and WLAN run in parallel with separate antenna */ |
| #define WL_BTC_HYBRID 5 /* hybrid coex, only ack is allowed to transmit in BT slot */ |
| #define WL_BTC_DEFAULT 8 /* set the default mode for the device */ |
| #define WL_INF_BTC_DISABLE 0 |
| #define WL_INF_BTC_ENABLE 1 |
| #define WL_INF_BTC_AUTO 3 |
| |
| /* BTC wire used by "btc_wire" iovar */ |
| #define WL_BTC_DEFWIRE 0 /* use default wire setting */ |
| #define WL_BTC_2WIRE 2 /* use 2-wire BTC */ |
| #define WL_BTC_3WIRE 3 /* use 3-wire BTC */ |
| #define WL_BTC_4WIRE 4 /* use 4-wire BTC */ |
| |
| /* BTC flags: BTC configuration that can be set by host */ |
| #define WL_BTC_FLAG_PREMPT (1 << 0) |
| #define WL_BTC_FLAG_BT_DEF (1 << 1) |
| #define WL_BTC_FLAG_ACTIVE_PROT (1 << 2) |
| #define WL_BTC_FLAG_SIM_RSP (1 << 3) |
| #define WL_BTC_FLAG_PS_PROTECT (1 << 4) |
| #define WL_BTC_FLAG_SIM_TX_LP (1 << 5) |
| #define WL_BTC_FLAG_ECI (1 << 6) |
| #define WL_BTC_FLAG_LIGHT (1 << 7) |
| #define WL_BTC_FLAG_PARALLEL (1 << 8) |
| |
| /* maximum channels returned by the get valid channels iovar */ |
| #define WL_NUMCHANNELS 64 |
| |
| /* max number of chanspecs (used by the iovar to calc. buf space) */ |
| #ifdef WL11AC_80P80 |
| #define WL_NUMCHANSPECS 206 |
| #else |
| #define WL_NUMCHANSPECS 110 |
| #endif |
| |
| /* WDS link local endpoint WPA role */ |
| #define WL_WDS_WPA_ROLE_AUTH 0 /* authenticator */ |
| #define WL_WDS_WPA_ROLE_SUP 1 /* supplicant */ |
| #define WL_WDS_WPA_ROLE_AUTO 255 /* auto, based on mac addr value */ |
| |
| /* Base offset values */ |
| #define WL_PKT_FILTER_BASE_PKT 0 |
| #define WL_PKT_FILTER_BASE_END 1 |
| #define WL_PKT_FILTER_BASE_D11_H 2 /* May be removed */ |
| #define WL_PKT_FILTER_BASE_D11_D 3 /* May be removed */ |
| #define WL_PKT_FILTER_BASE_ETH_H 4 |
| #define WL_PKT_FILTER_BASE_ETH_D 5 |
| #define WL_PKT_FILTER_BASE_ARP_H 6 |
| #define WL_PKT_FILTER_BASE_ARP_D 7 /* May be removed */ |
| #define WL_PKT_FILTER_BASE_IP4_H 8 |
| #define WL_PKT_FILTER_BASE_IP4_D 9 |
| #define WL_PKT_FILTER_BASE_IP6_H 10 |
| #define WL_PKT_FILTER_BASE_IP6_D 11 |
| #define WL_PKT_FILTER_BASE_TCP_H 12 |
| #define WL_PKT_FILTER_BASE_TCP_D 13 /* May be removed */ |
| #define WL_PKT_FILTER_BASE_UDP_H 14 |
| #define WL_PKT_FILTER_BASE_UDP_D 15 |
| #define WL_PKT_FILTER_BASE_IP6_P 16 |
| #define WL_PKT_FILTER_BASE_COUNT 17 /* May be removed */ |
| |
| /* String mapping for bases that may be used by applications or debug */ |
| #define WL_PKT_FILTER_BASE_NAMES \ |
| { "START", WL_PKT_FILTER_BASE_PKT }, \ |
| { "END", WL_PKT_FILTER_BASE_END }, \ |
| { "ETH_H", WL_PKT_FILTER_BASE_ETH_H }, \ |
| { "ETH_D", WL_PKT_FILTER_BASE_ETH_D }, \ |
| { "D11_H", WL_PKT_FILTER_BASE_D11_H }, \ |
| { "D11_D", WL_PKT_FILTER_BASE_D11_D }, \ |
| { "ARP_H", WL_PKT_FILTER_BASE_ARP_H }, \ |
| { "IP4_H", WL_PKT_FILTER_BASE_IP4_H }, \ |
| { "IP4_D", WL_PKT_FILTER_BASE_IP4_D }, \ |
| { "IP6_H", WL_PKT_FILTER_BASE_IP6_H }, \ |
| { "IP6_D", WL_PKT_FILTER_BASE_IP6_D }, \ |
| { "IP6_P", WL_PKT_FILTER_BASE_IP6_P }, \ |
| { "TCP_H", WL_PKT_FILTER_BASE_TCP_H }, \ |
| { "TCP_D", WL_PKT_FILTER_BASE_TCP_D }, \ |
| { "UDP_H", WL_PKT_FILTER_BASE_UDP_H }, \ |
| { "UDP_D", WL_PKT_FILTER_BASE_UDP_D } |
| |
| /* Flags for a pattern list element */ |
| #define WL_PKT_FILTER_MFLAG_NEG 0x0001 |
| |
| /* |
| * Packet engine interface |
| */ |
| |
| #define WL_PKTENG_PER_TX_START 0x01 |
| #define WL_PKTENG_PER_TX_STOP 0x02 |
| #define WL_PKTENG_PER_RX_START 0x04 |
| #define WL_PKTENG_PER_RX_WITH_ACK_START 0x05 |
| #define WL_PKTENG_PER_TX_WITH_ACK_START 0x06 |
| #define WL_PKTENG_PER_RX_STOP 0x08 |
| #define WL_PKTENG_PER_MASK 0xff |
| |
| #define WL_PKTENG_SYNCHRONOUS 0x100 /* synchronous flag */ |
| #define WL_PKTENG_SYNCHRONOUS_UNBLK 0x200 /* synchronous unblock flag */ |
| #ifdef PKTENG_LONGPKTSZ |
| /* max pktsz limit for pkteng */ |
| #define WL_PKTENG_MAXPKTSZ PKTENG_LONGPKTSZ |
| #else |
| #define WL_PKTENG_MAXPKTSZ 16384 |
| #endif |
| |
| #define NUM_80211b_RATES 4 |
| #define NUM_80211ag_RATES 8 |
| #define NUM_80211n_RATES 32 |
| #define NUM_80211_RATES (NUM_80211b_RATES+NUM_80211ag_RATES+NUM_80211n_RATES) |
| |
| /* |
| * WOWL capability/override settings |
| */ |
| #define WL_WOWL_MAGIC (1 << 0) /* Wakeup on Magic packet */ |
| #define WL_WOWL_NET (1 << 1) /* Wakeup on Netpattern */ |
| #define WL_WOWL_DIS (1 << 2) /* Wakeup on loss-of-link due to Disassoc/Deauth */ |
| #define WL_WOWL_RETR (1 << 3) /* Wakeup on retrograde TSF */ |
| #define WL_WOWL_BCN (1 << 4) /* Wakeup on loss of beacon */ |
| #define WL_WOWL_TST (1 << 5) /* Wakeup after test */ |
| #define WL_WOWL_M1 (1 << 6) /* Wakeup after PTK refresh */ |
| #define WL_WOWL_EAPID (1 << 7) /* Wakeup after receipt of EAP-Identity Req */ |
| #define WL_WOWL_PME_GPIO (1 << 8) /* Wakeind via PME(0) or GPIO(1) */ |
| #define WL_WOWL_ULP_BAILOUT (1 << 8) /* wakeind via unknown pkt by basic ULP-offloads - |
| * WL_WOWL_ULP_BAILOUT - same as WL_WOWL_PME_GPIO used only for DONGLE BUILDS |
| */ |
| #define WL_WOWL_NEEDTKIP1 (1 << 9) /* need tkip phase 1 key to be updated by the driver */ |
| #define WL_WOWL_GTK_FAILURE (1 << 10) /* enable wakeup if GTK fails */ |
| #define WL_WOWL_EXTMAGPAT (1 << 11) /* support extended magic packets */ |
| #define WL_WOWL_ARPOFFLOAD (1 << 12) /* support ARP/NS/keepalive offloading */ |
| #define WL_WOWL_WPA2 (1 << 13) /* read protocol version for EAPOL frames */ |
| #define WL_WOWL_KEYROT (1 << 14) /* If the bit is set, use key rotaton */ |
| #define WL_WOWL_BCAST (1 << 15) /* If the bit is set, frm received was bcast frame */ |
| #define WL_WOWL_SCANOL (1 << 16) /* If the bit is set, scan offload is enabled */ |
| #define WL_WOWL_TCPKEEP_TIME (1 << 17) /* Wakeup on tcpkeep alive timeout */ |
| #define WL_WOWL_MDNS_CONFLICT (1 << 18) /* Wakeup on mDNS Conflict Resolution */ |
| #define WL_WOWL_MDNS_SERVICE (1 << 19) /* Wakeup on mDNS Service Connect */ |
| #define WL_WOWL_TCPKEEP_DATA (1 << 20) /* tcp keepalive got data */ |
| #define WL_WOWL_FW_HALT (1 << 21) /* Firmware died in wowl mode */ |
| #define WL_WOWL_ENAB_HWRADIO (1 << 22) /* Enable detection of radio button changes */ |
| #define WL_WOWL_MIC_FAIL (1 << 23) /* Offloads detected MIC failure(s) */ |
| #define WL_WOWL_UNASSOC (1 << 24) /* Wakeup in Unassociated state (Net/Magic Pattern) */ |
| #define WL_WOWL_SECURE (1 << 25) /* Wakeup if received matched secured pattern */ |
| #define WL_WOWL_EXCESS_WAKE (1 << 26) /* Excess wake */ |
| #define WL_WOWL_LINKDOWN (1 << 31) /* Link Down indication in WoWL mode */ |
| |
| #define WL_WOWL_TCPKEEP (1 << 20) /* temp copy to satisfy automerger */ |
| #define MAGIC_PKT_MINLEN 102 /* Magic pkt min length is 6 * 0xFF + 16 * ETHER_ADDR_LEN */ |
| |
| #define WOWL_PATTEN_TYPE_ARP (1 << 0) /* ARP offload Pattern */ |
| #define WOWL_PATTEN_TYPE_NA (1 << 1) /* NA offload Pattern */ |
| |
| #define MAGIC_PKT_MINLEN 102 /* Magic pkt min length is 6 * 0xFF + 16 * ETHER_ADDR_LEN */ |
| #define MAGIC_PKT_NUM_MAC_ADDRS 16 |
| |
| /* Overlap BSS Scan parameters default, minimum, maximum */ |
| #define WLC_OBSS_SCAN_PASSIVE_DWELL_DEFAULT 20 /* unit TU */ |
| #define WLC_OBSS_SCAN_PASSIVE_DWELL_MIN 5 /* unit TU */ |
| #define WLC_OBSS_SCAN_PASSIVE_DWELL_MAX 1000 /* unit TU */ |
| #define WLC_OBSS_SCAN_ACTIVE_DWELL_DEFAULT 10 /* unit TU */ |
| #define WLC_OBSS_SCAN_ACTIVE_DWELL_MIN 10 /* unit TU */ |
| #define WLC_OBSS_SCAN_ACTIVE_DWELL_MAX 1000 /* unit TU */ |
| #define WLC_OBSS_SCAN_WIDTHSCAN_INTERVAL_DEFAULT 300 /* unit Sec */ |
| #define WLC_OBSS_SCAN_WIDTHSCAN_INTERVAL_MIN 10 /* unit Sec */ |
| #define WLC_OBSS_SCAN_WIDTHSCAN_INTERVAL_MAX 900 /* unit Sec */ |
| #define WLC_OBSS_SCAN_CHANWIDTH_TRANSITION_DLY_DEFAULT 5 |
| #define WLC_OBSS_SCAN_CHANWIDTH_TRANSITION_DLY_MIN 5 |
| #define WLC_OBSS_SCAN_CHANWIDTH_TRANSITION_DLY_MAX 100 |
| #define WLC_OBSS_SCAN_PASSIVE_TOTAL_PER_CHANNEL_DEFAULT 200 /* unit TU */ |
| #define WLC_OBSS_SCAN_PASSIVE_TOTAL_PER_CHANNEL_MIN 200 /* unit TU */ |
| #define WLC_OBSS_SCAN_PASSIVE_TOTAL_PER_CHANNEL_MAX 10000 /* unit TU */ |
| #define WLC_OBSS_SCAN_ACTIVE_TOTAL_PER_CHANNEL_DEFAULT 20 /* unit TU */ |
| #define WLC_OBSS_SCAN_ACTIVE_TOTAL_PER_CHANNEL_MIN 20 /* unit TU */ |
| #define WLC_OBSS_SCAN_ACTIVE_TOTAL_PER_CHANNEL_MAX 10000 /* unit TU */ |
| #define WLC_OBSS_SCAN_ACTIVITY_THRESHOLD_DEFAULT 25 /* unit percent */ |
| #define WLC_OBSS_SCAN_ACTIVITY_THRESHOLD_MIN 0 /* unit percent */ |
| #define WLC_OBSS_SCAN_ACTIVITY_THRESHOLD_MAX 100 /* unit percent */ |
| |
| #define WL_MIN_NUM_OBSS_SCAN_ARG 7 /* minimum number of arguments required for OBSS Scan */ |
| |
| #define WL_COEX_INFO_MASK 0x07 |
| #define WL_COEX_INFO_REQ 0x01 |
| #define WL_COEX_40MHZ_INTOLERANT 0x02 |
| #define WL_COEX_WIDTH20 0x04 |
| |
| #define WLC_RSSI_INVALID 0 /* invalid RSSI value */ |
| |
| #define MAX_RSSI_LEVELS 8 |
| |
| /* **** EXTLOG **** */ |
| #define EXTLOG_CUR_VER 0x0100 |
| |
| #define MAX_ARGSTR_LEN 18 /* At least big enough for storing ETHER_ADDR_STR_LEN */ |
| |
| /* log modules (bitmap) */ |
| #define LOG_MODULE_COMMON 0x0001 |
| #define LOG_MODULE_ASSOC 0x0002 |
| #define LOG_MODULE_EVENT 0x0004 |
| #define LOG_MODULE_MAX 3 /* Update when adding module */ |
| |
| /* log levels */ |
| #define WL_LOG_LEVEL_DISABLE 0 |
| #define WL_LOG_LEVEL_ERR 1 |
| #define WL_LOG_LEVEL_WARN 2 |
| #define WL_LOG_LEVEL_INFO 3 |
| #define WL_LOG_LEVEL_MAX WL_LOG_LEVEL_INFO /* Update when adding level */ |
| |
| /* flag */ |
| #define LOG_FLAG_EVENT 1 |
| |
| /* log arg_type */ |
| #define LOG_ARGTYPE_NULL 0 |
| #define LOG_ARGTYPE_STR 1 /* %s */ |
| #define LOG_ARGTYPE_INT 2 /* %d */ |
| #define LOG_ARGTYPE_INT_STR 3 /* %d...%s */ |
| #define LOG_ARGTYPE_STR_INT 4 /* %s...%d */ |
| |
| /* 802.11 Mgmt Packet flags */ |
| #define VNDR_IE_BEACON_FLAG 0x1 |
| #define VNDR_IE_PRBRSP_FLAG 0x2 |
| #define VNDR_IE_ASSOCRSP_FLAG 0x4 |
| #define VNDR_IE_AUTHRSP_FLAG 0x8 |
| #define VNDR_IE_PRBREQ_FLAG 0x10 |
| #define VNDR_IE_ASSOCREQ_FLAG 0x20 |
| #define VNDR_IE_IWAPID_FLAG 0x40 /* vendor IE in IW advertisement protocol ID field */ |
| #define VNDR_IE_AUTHREQ_FLAG 0x80 |
| #define VNDR_IE_CUSTOM_FLAG 0x100 /* allow custom IE id */ |
| |
| #if defined(WLP2P) |
| /* P2P Action Frames flags (spec ordered) */ |
| #define VNDR_IE_GONREQ_FLAG 0x001000 |
| #define VNDR_IE_GONRSP_FLAG 0x002000 |
| #define VNDR_IE_GONCFM_FLAG 0x004000 |
| #define VNDR_IE_INVREQ_FLAG 0x008000 |
| #define VNDR_IE_INVRSP_FLAG 0x010000 |
| #define VNDR_IE_DISREQ_FLAG 0x020000 |
| #define VNDR_IE_DISRSP_FLAG 0x040000 |
| #define VNDR_IE_PRDREQ_FLAG 0x080000 |
| #define VNDR_IE_PRDRSP_FLAG 0x100000 |
| |
| #define VNDR_IE_P2PAF_SHIFT 12 |
| #endif /* WLP2P */ |
| |
| /* channel interference measurement (chanim) related defines */ |
| |
| /* chanim mode */ |
| #define CHANIM_DISABLE 0 /* disabled */ |
| #define CHANIM_DETECT 1 /* detection only */ |
| #define CHANIM_EXT 2 /* external state machine */ |
| #define CHANIM_ACT 3 /* full internal state machine, detect + act */ |
| #define CHANIM_MODE_MAX 4 |
| |
| /* define for apcs reason code */ |
| #define APCS_INIT 0 |
| #define APCS_IOCTL 1 |
| #define APCS_CHANIM 2 |
| #define APCS_CSTIMER 3 |
| #define APCS_BTA 4 |
| #define APCS_TXDLY 5 |
| #define APCS_NONACSD 6 |
| #define APCS_DFS_REENTRY 7 |
| #define APCS_TXFAIL 8 |
| #define APCS_MAX 9 |
| |
| /* number of ACS record entries */ |
| #define CHANIM_ACS_RECORD 10 |
| |
| /* CHANIM */ |
| #define CCASTATS_TXDUR 0 |
| #define CCASTATS_INBSS 1 |
| #define CCASTATS_OBSS 2 |
| #define CCASTATS_NOCTG 3 |
| #define CCASTATS_NOPKT 4 |
| #define CCASTATS_DOZE 5 |
| #define CCASTATS_TXOP 6 |
| #define CCASTATS_GDTXDUR 7 |
| #define CCASTATS_BDTXDUR 8 |
| |
| #ifndef WLCHANIM_V2 |
| #define CCASTATS_MAX 9 |
| #else /* WLCHANIM_V2 */ |
| #define CCASTATS_MYRX 9 |
| #define CCASTATS_MAX 10 |
| #endif /* WLCHANIM_V2 */ |
| |
| #define WL_CHANIM_COUNT_ALL 0xff |
| #define WL_CHANIM_COUNT_ONE 0x1 |
| |
| /* ap tpc modes */ |
| #define AP_TPC_OFF 0 |
| #define AP_TPC_BSS_PWR 1 /* BSS power control */ |
| #define AP_TPC_AP_PWR 2 /* AP power control */ |
| #define AP_TPC_AP_BSS_PWR 3 /* Both AP and BSS power control */ |
| #define AP_TPC_MAX_LINK_MARGIN 127 |
| |
| /* ap tpc modes */ |
| #define AP_TPC_OFF 0 |
| #define AP_TPC_BSS_PWR 1 /* BSS power control */ |
| #define AP_TPC_AP_PWR 2 /* AP power control */ |
| #define AP_TPC_AP_BSS_PWR 3 /* Both AP and BSS power control */ |
| #define AP_TPC_MAX_LINK_MARGIN 127 |
| |
| /* state */ |
| #define WL_P2P_DISC_ST_SCAN 0 |
| #define WL_P2P_DISC_ST_LISTEN 1 |
| #define WL_P2P_DISC_ST_SEARCH 2 |
| |
| /* i/f type */ |
| #define WL_P2P_IF_CLIENT 0 |
| #define WL_P2P_IF_GO 1 |
| #define WL_P2P_IF_DYNBCN_GO 2 |
| #define WL_P2P_IF_DEV 3 |
| |
| /* count */ |
| #define WL_P2P_SCHED_RSVD 0 |
| #define WL_P2P_SCHED_REPEAT 255 /* anything > 255 will be treated as 255 */ |
| |
| #define WL_P2P_SCHED_FIXED_LEN 3 |
| |
| /* schedule type */ |
| #define WL_P2P_SCHED_TYPE_ABS 0 /* Scheduled Absence */ |
| #define WL_P2P_SCHED_TYPE_REQ_ABS 1 /* Requested Absence */ |
| |
| /* schedule action during absence periods (for WL_P2P_SCHED_ABS type) */ |
| #define WL_P2P_SCHED_ACTION_NONE 0 /* no action */ |
| #define WL_P2P_SCHED_ACTION_DOZE 1 /* doze */ |
| /* schedule option - WL_P2P_SCHED_TYPE_REQ_ABS */ |
| #define WL_P2P_SCHED_ACTION_GOOFF 2 /* turn off GO beacon/prbrsp functions */ |
| /* schedule option - WL_P2P_SCHED_TYPE_XXX */ |
| #define WL_P2P_SCHED_ACTION_RESET 255 /* reset */ |
| |
| /* schedule option - WL_P2P_SCHED_TYPE_ABS */ |
| #define WL_P2P_SCHED_OPTION_NORMAL 0 /* normal start/interval/duration/count */ |
| #define WL_P2P_SCHED_OPTION_BCNPCT 1 /* percentage of beacon interval */ |
| /* schedule option - WL_P2P_SCHED_TYPE_REQ_ABS */ |
| #define WL_P2P_SCHED_OPTION_TSFOFS 2 /* normal start/internal/duration/count with |
| * start being an offset of the 'current' TSF |
| */ |
| |
| /* feature flags */ |
| #define WL_P2P_FEAT_GO_CSA (1 << 0) /* GO moves with the STA using CSA method */ |
| #define WL_P2P_FEAT_GO_NOLEGACY (1 << 1) /* GO does not probe respond to non-p2p probe |
| * requests |
| */ |
| #define WL_P2P_FEAT_RESTRICT_DEV_RESP (1 << 2) /* Restrict p2p dev interface from responding */ |
| |
| /* n-mode support capability */ |
| /* 2x2 includes both 1x1 & 2x2 devices |
| * reserved #define 2 for future when we want to separate 1x1 & 2x2 and |
| * control it independently |
| */ |
| #define WL_11N_2x2 1 |
| #define WL_11N_3x3 3 |
| #define WL_11N_4x4 4 |
| |
| /* define 11n feature disable flags */ |
| #define WLFEATURE_DISABLE_11N 0x00000001 |
| #define WLFEATURE_DISABLE_11N_STBC_TX 0x00000002 |
| #define WLFEATURE_DISABLE_11N_STBC_RX 0x00000004 |
| #define WLFEATURE_DISABLE_11N_SGI_TX 0x00000008 |
| #define WLFEATURE_DISABLE_11N_SGI_RX 0x00000010 |
| #define WLFEATURE_DISABLE_11N_AMPDU_TX 0x00000020 |
| #define WLFEATURE_DISABLE_11N_AMPDU_RX 0x00000040 |
| #define WLFEATURE_DISABLE_11N_GF 0x00000080 |
| |
| /* Proxy STA modes */ |
| #define PSTA_MODE_DISABLED 0 |
| #define PSTA_MODE_PROXY 1 |
| #define PSTA_MODE_REPEATER 2 |
| |
| /* op code in nat_cfg */ |
| #define NAT_OP_ENABLE 1 /* enable NAT on given interface */ |
| #define NAT_OP_DISABLE 2 /* disable NAT on given interface */ |
| #define NAT_OP_DISABLE_ALL 3 /* disable NAT on all interfaces */ |
| |
| /* NAT state */ |
| #define NAT_STATE_ENABLED 1 /* NAT is enabled */ |
| #define NAT_STATE_DISABLED 2 /* NAT is disabled */ |
| |
| #define CHANNEL_5G_LOW_START 36 /* 5G low (36..48) CDD enable/disable bit mask */ |
| #define CHANNEL_5G_MID_START 52 /* 5G mid (52..64) CDD enable/disable bit mask */ |
| #define CHANNEL_5G_HIGH_START 100 /* 5G high (100..140) CDD enable/disable bit mask */ |
| #define CHANNEL_5G_UPPER_START 149 /* 5G upper (149..161) CDD enable/disable bit mask */ |
| |
| /* D0 Coalescing */ |
| #define IPV4_ARP_FILTER 0x0001 |
| #define IPV4_NETBT_FILTER 0x0002 |
| #define IPV4_LLMNR_FILTER 0x0004 |
| #define IPV4_SSDP_FILTER 0x0008 |
| #define IPV4_WSD_FILTER 0x0010 |
| #define IPV6_NETBT_FILTER 0x0200 |
| #define IPV6_LLMNR_FILTER 0x0400 |
| #define IPV6_SSDP_FILTER 0x0800 |
| #define IPV6_WSD_FILTER 0x1000 |
| |
| /* Network Offload Engine */ |
| #define NWOE_OL_ENABLE 0x00000001 |
| |
| /* |
| * Traffic management structures/defines. |
| */ |
| |
| /* Traffic management bandwidth parameters */ |
| #define TRF_MGMT_MAX_PRIORITIES 3 |
| |
| #define TRF_MGMT_FLAG_ADD_DSCP 0x0001 /* Add DSCP to IP TOS field */ |
| #define TRF_MGMT_FLAG_DISABLE_SHAPING 0x0002 /* Don't shape traffic */ |
| #define TRF_MGMT_FLAG_MANAGE_LOCAL_TRAFFIC 0x0008 /* Manage traffic over our local subnet */ |
| #define TRF_MGMT_FLAG_FILTER_ON_MACADDR 0x0010 /* filter on MAC address */ |
| #define TRF_MGMT_FLAG_NO_RX 0x0020 /* do not apply fiters to rx packets */ |
| |
| #define TRF_FILTER_MAC_ADDR 0x0001 /* L2 filter use dst mac address for filtering */ |
| #define TRF_FILTER_IP_ADDR 0x0002 /* L3 filter use ip ddress for filtering */ |
| #define TRF_FILTER_L4 0x0004 /* L4 filter use tcp/udp for filtering */ |
| #define TRF_FILTER_DWM 0x0008 /* L3 filter use DSCP for filtering */ |
| #define TRF_FILTER_FAVORED 0x0010 /* Tag the packet FAVORED */ |
| |
| /* WNM/NPS subfeatures mask */ |
| #define WL_WNM_BSSTRANS 0x00000001 |
| #define WL_WNM_PROXYARP 0x00000002 |
| #define WL_WNM_MAXIDLE 0x00000004 |
| #define WL_WNM_TIMBC 0x00000008 |
| #define WL_WNM_TFS 0x00000010 |
| #define WL_WNM_SLEEP 0x00000020 |
| #define WL_WNM_DMS 0x00000040 |
| #define WL_WNM_FMS 0x00000080 |
| #define WL_WNM_NOTIF 0x00000100 |
| #define WL_WNM_WBTEXT 0x00000200 |
| #define WL_WNM_MAX 0x00000400 |
| #ifdef WLWNM_BRCM |
| #define BRCM_WNM_FEATURE_SET\ |
| (WL_WNM_PROXYARP | \ |
| WL_WNM_SLEEP | \ |
| WL_WNM_FMS | \ |
| WL_WNM_TFS | \ |
| WL_WNM_TIMBC | \ |
| WL_WNM_BSSTRANS | \ |
| WL_WNM_DMS | \ |
| WL_WNM_NOTIF | \ |
| 0) |
| #endif /* WLWNM_BRCM */ |
| #ifndef ETHER_MAX_DATA |
| #define ETHER_MAX_DATA 1500 |
| #endif /* ETHER_MAX_DATA */ |
| |
| /* Different discovery modes for dpt */ |
| #define DPT_DISCOVERY_MANUAL 0x01 /* manual discovery mode */ |
| #define DPT_DISCOVERY_AUTO 0x02 /* auto discovery mode */ |
| #define DPT_DISCOVERY_SCAN 0x04 /* scan-based discovery mode */ |
| |
| /* different path selection values */ |
| #define DPT_PATHSEL_AUTO 0 /* auto mode for path selection */ |
| #define DPT_PATHSEL_DIRECT 1 /* always use direct DPT path */ |
| #define DPT_PATHSEL_APPATH 2 /* always use AP path */ |
| |
| /* different ops for deny list */ |
| #define DPT_DENY_LIST_ADD 1 /* add to dpt deny list */ |
| #define DPT_DENY_LIST_REMOVE 2 /* remove from dpt deny list */ |
| |
| /* different ops for manual end point */ |
| #define DPT_MANUAL_EP_CREATE 1 /* create manual dpt endpoint */ |
| #define DPT_MANUAL_EP_MODIFY 2 /* modify manual dpt endpoint */ |
| #define DPT_MANUAL_EP_DELETE 3 /* delete manual dpt endpoint */ |
| |
| /* flags to indicate DPT status */ |
| #define DPT_STATUS_ACTIVE 0x01 /* link active (though may be suspended) */ |
| #define DPT_STATUS_AES 0x02 /* link secured through AES encryption */ |
| #define DPT_STATUS_FAILED 0x04 /* DPT link failed */ |
| |
| #ifdef WLTDLS |
| /* different ops for manual end point */ |
| #define TDLS_MANUAL_EP_CREATE 1 /* create manual dpt endpoint */ |
| #define TDLS_MANUAL_EP_MODIFY 2 /* modify manual dpt endpoint */ |
| #define TDLS_MANUAL_EP_DELETE 3 /* delete manual dpt endpoint */ |
| #define TDLS_MANUAL_EP_PM 4 /* put dpt endpoint in PM mode */ |
| #define TDLS_MANUAL_EP_WAKE 5 /* wake up dpt endpoint from PM */ |
| #define TDLS_MANUAL_EP_DISCOVERY 6 /* discover if endpoint is TDLS capable */ |
| #define TDLS_MANUAL_EP_CHSW 7 /* channel switch */ |
| #define TDLS_MANUAL_EP_WFD_TPQ 8 /* WiFi-Display Tunneled Probe reQuest */ |
| |
| /* modes */ |
| #define TDLS_WFD_IE_TX 0 |
| #define TDLS_WFD_IE_RX 1 |
| #define TDLS_WFD_PROBE_IE_TX 2 |
| #define TDLS_WFD_PROBE_IE_RX 3 |
| #endif /* WLTDLS */ |
| |
| /* define for flag */ |
| #define TSPEC_PENDING 0 /* TSPEC pending */ |
| #define TSPEC_ACCEPTED 1 /* TSPEC accepted */ |
| #define TSPEC_REJECTED 2 /* TSPEC rejected */ |
| #define TSPEC_UNKNOWN 3 /* TSPEC unknown */ |
| #define TSPEC_STATUS_MASK 7 /* TSPEC status mask */ |
| |
| |
| /* Software feature flag defines used by wlfeatureflag */ |
| #ifdef WLAFTERBURNER |
| #define WL_SWFL_ABBFL 0x0001 /* Allow Afterburner on systems w/o hardware BFL */ |
| #define WL_SWFL_ABENCORE 0x0002 /* Allow AB on non-4318E chips */ |
| #endif /* WLAFTERBURNER */ |
| #define WL_SWFL_NOHWRADIO 0x0004 |
| #define WL_SWFL_FLOWCONTROL 0x0008 /* Enable backpressure to OS stack */ |
| #define WL_SWFL_WLBSSSORT 0x0010 /* Per-port supports sorting of BSS */ |
| |
| #define WL_LIFETIME_MAX 0xFFFF /* Max value in ms */ |
| |
| #define CSA_BROADCAST_ACTION_FRAME 0 /* csa broadcast action frame */ |
| #define CSA_UNICAST_ACTION_FRAME 1 /* csa unicast action frame */ |
| |
| /* Roaming trigger definitions for WLC_SET_ROAM_TRIGGER. |
| * |
| * (-100 < value < 0) value is used directly as a roaming trigger in dBm |
| * (0 <= value) value specifies a logical roaming trigger level from |
| * the list below |
| * |
| * WLC_GET_ROAM_TRIGGER always returns roaming trigger value in dBm, never |
| * the logical roam trigger value. |
| */ |
| #define WLC_ROAM_TRIGGER_DEFAULT 0 /* default roaming trigger */ |
| #define WLC_ROAM_TRIGGER_BANDWIDTH 1 /* optimize for bandwidth roaming trigger */ |
| #define WLC_ROAM_TRIGGER_DISTANCE 2 /* optimize for distance roaming trigger */ |
| #define WLC_ROAM_TRIGGER_AUTO 3 /* auto-detect environment */ |
| #define WLC_ROAM_TRIGGER_MAX_VALUE 3 /* max. valid value */ |
| |
| #define WLC_ROAM_NEVER_ROAM_TRIGGER (-100) /* Avoid Roaming by setting a large value */ |
| |
| /* Preferred Network Offload (PNO, formerly PFN) defines */ |
| #define WPA_AUTH_PFN_ANY 0xffffffff /* for PFN, match only ssid */ |
| |
| #define SORT_CRITERIA_BIT 0 |
| #define AUTO_NET_SWITCH_BIT 1 |
| #define ENABLE_BKGRD_SCAN_BIT 2 |
| #define IMMEDIATE_SCAN_BIT 3 |
| #define AUTO_CONNECT_BIT 4 |
| #define ENABLE_BD_SCAN_BIT 5 |
| #define ENABLE_ADAPTSCAN_BIT 6 |
| #define IMMEDIATE_EVENT_BIT 8 |
| #define SUPPRESS_SSID_BIT 9 |
| #define ENABLE_NET_OFFLOAD_BIT 10 |
| /* report found/lost events for SSID and BSSID networks seperately */ |
| #define REPORT_SEPERATELY_BIT 11 |
| #define BESTN_BSSID_ONLY_BIT 12 |
| |
| #define SORT_CRITERIA_MASK 0x0001 |
| #define AUTO_NET_SWITCH_MASK 0x0002 |
| #define ENABLE_BKGRD_SCAN_MASK 0x0004 |
| #define IMMEDIATE_SCAN_MASK 0x0008 |
| #define AUTO_CONNECT_MASK 0x0010 |
| |
| #define ENABLE_BD_SCAN_MASK 0x0020 |
| #define ENABLE_ADAPTSCAN_MASK 0x00c0 |
| #define IMMEDIATE_EVENT_MASK 0x0100 |
| #define SUPPRESS_SSID_MASK 0x0200 |
| #define ENABLE_NET_OFFLOAD_MASK 0x0400 |
| /* report found/lost events for SSID and BSSID networks seperately */ |
| #define REPORT_SEPERATELY_MASK 0x0800 |
| #define BESTN_BSSID_ONLY_MASK 0x1000 |
| |
| #define PFN_VERSION 2 |
| #ifdef PFN_SCANRESULT_2 |
| #define PFN_SCANRESULT_VERSION 2 |
| #else |
| #define PFN_SCANRESULT_VERSION 1 |
| #endif /* PFN_SCANRESULT_2 */ |
| #ifndef MAX_PFN_LIST_COUNT |
| #define MAX_PFN_LIST_COUNT 16 |
| #endif /* MAX_PFN_LIST_COUNT */ |
| |
| #define PFN_COMPLETE 1 |
| #define PFN_INCOMPLETE 0 |
| |
| #define DEFAULT_BESTN 2 |
| #define DEFAULT_MSCAN 0 |
| #define DEFAULT_REPEAT 10 |
| #define DEFAULT_EXP 2 |
| |
| #define PFN_PARTIAL_SCAN_BIT 0 |
| #define PFN_PARTIAL_SCAN_MASK 1 |
| |
| #define WL_PFN_SUPPRESSFOUND_MASK 0x08 |
| #define WL_PFN_SUPPRESSLOST_MASK 0x10 |
| #define WL_PFN_SSID_A_BAND_TRIG 0x20 |
| #define WL_PFN_SSID_BG_BAND_TRIG 0x40 |
| #define WL_PFN_SSID_IMPRECISE_MATCH 0x80 |
| #define WL_PFN_SSID_SAME_NETWORK 0x10000 |
| #define WL_PFN_SUPPRESS_AGING_MASK 0x20000 |
| #define WL_PFN_FLUSH_ALL_SSIDS 0x40000 |
| #define WL_PFN_RSSI_MASK 0xff00 |
| #define WL_PFN_RSSI_SHIFT 8 |
| |
| #define WL_PFN_REPORT_ALLNET 0 |
| #define WL_PFN_REPORT_SSIDNET 1 |
| #define WL_PFN_REPORT_BSSIDNET 2 |
| |
| #define WL_PFN_CFG_FLAGS_PROHIBITED 0x00000001 /* Accept and use prohibited channels */ |
| #define WL_PFN_CFG_FLAGS_HISTORY_OFF 0x00000002 /* Scan history suppressed */ |
| |
| #define WL_PFN_HIDDEN_BIT 2 |
| #define PNO_SCAN_MAX_FW 508*1000 /* max time scan time in msec */ |
| #define PNO_SCAN_MAX_FW_SEC PNO_SCAN_MAX_FW/1000 /* max time scan time in SEC */ |
| #define PNO_SCAN_MIN_FW_SEC 10 /* min time scan time in SEC */ |
| #define WL_PFN_HIDDEN_MASK 0x4 |
| #define MAX_SSID_WHITELIST_NUM 4 |
| #define MAX_BSSID_PREF_LIST_NUM 32 |
| #define MAX_BSSID_BLACKLIST_NUM 32 |
| |
| #ifndef BESTN_MAX |
| #define BESTN_MAX 10 |
| #endif |
| |
| #ifndef MSCAN_MAX |
| #define MSCAN_MAX 32 |
| #endif |
| |
| /* TCP Checksum Offload error injection for testing */ |
| #define TOE_ERRTEST_TX_CSUM 0x00000001 |
| #define TOE_ERRTEST_RX_CSUM 0x00000002 |
| #define TOE_ERRTEST_RX_CSUM2 0x00000004 |
| |
| /* ARP Offload feature flags for arp_ol iovar */ |
| #define ARP_OL_AGENT 0x00000001 |
| #define ARP_OL_SNOOP 0x00000002 |
| #define ARP_OL_HOST_AUTO_REPLY 0x00000004 |
| #define ARP_OL_PEER_AUTO_REPLY 0x00000008 |
| |
| /* ARP Offload error injection */ |
| #define ARP_ERRTEST_REPLY_PEER 0x1 |
| #define ARP_ERRTEST_REPLY_HOST 0x2 |
| |
| #define ARP_MULTIHOMING_MAX 8 /* Maximum local host IP addresses */ |
| #define ND_MULTIHOMING_MAX 10 /* Maximum local host IP addresses */ |
| #define ND_REQUEST_MAX 5 /* Max set of offload params */ |
| /* AOAC wake event flag */ |
| #define WAKE_EVENT_NLO_DISCOVERY_BIT 1 |
| #define WAKE_EVENT_AP_ASSOCIATION_LOST_BIT 2 |
| #define WAKE_EVENT_GTK_HANDSHAKE_ERROR_BIT 4 |
| #define WAKE_EVENT_4WAY_HANDSHAKE_REQUEST_BIT 8 |
| #define WAKE_EVENT_NET_PACKET_BIT 0x10 |
| |
| #define MAX_NUM_WOL_PATTERN 22 /* LOGO requirements min 22 */ |
| |
| |
| /* Packet filter operation mode */ |
| /* True: 1; False: 0 */ |
| #define PKT_FILTER_MODE_FORWARD_ON_MATCH 1 |
| /* Enable and disable pkt_filter as a whole */ |
| #define PKT_FILTER_MODE_DISABLE 2 |
| /* Cache first matched rx pkt(be queried by host later) */ |
| #define PKT_FILTER_MODE_PKT_CACHE_ON_MATCH 4 |
| /* If pkt_filter is enabled and no filter is set, don't forward anything */ |
| #define PKT_FILTER_MODE_PKT_FORWARD_OFF_DEFAULT 8 |
| |
| #ifdef DONGLEOVERLAYS |
| #define OVERLAY_IDX_MASK 0x000000ff |
| #define OVERLAY_IDX_SHIFT 0 |
| #define OVERLAY_FLAGS_MASK 0xffffff00 |
| #define OVERLAY_FLAGS_SHIFT 8 |
| /* overlay written to device memory immediately after loading the base image */ |
| #define OVERLAY_FLAG_POSTLOAD 0x100 |
| /* defer overlay download until the device responds w/WLC_E_OVL_DOWNLOAD event */ |
| #define OVERLAY_FLAG_DEFER_DL 0x200 |
| /* overlay downloaded prior to the host going to sleep */ |
| #define OVERLAY_FLAG_PRESLEEP 0x400 |
| #define OVERLAY_DOWNLOAD_CHUNKSIZE 1024 |
| #endif /* DONGLEOVERLAYS */ |
| |
| /* reuse two number in the sc/rc space */ |
| #define SMFS_CODE_MALFORMED 0xFFFE |
| #define SMFS_CODE_IGNORED 0xFFFD |
| |
| /* RFAWARE def */ |
| #define BCM_ACTION_RFAWARE 0x77 |
| #define BCM_ACTION_RFAWARE_DCS 0x01 |
| |
| /* DCS reason code define */ |
| #define BCM_DCS_IOVAR 0x1 |
| #define BCM_DCS_UNKNOWN 0xFF |
| |
| #ifdef PROP_TXSTATUS |
| /* Bit definitions for tlv iovar */ |
| /* |
| * enable RSSI signals: |
| * WLFC_CTL_TYPE_RSSI |
| */ |
| #define WLFC_FLAGS_RSSI_SIGNALS 0x0001 |
| |
| /* enable (if/mac_open, if/mac_close,, mac_add, mac_del) signals: |
| * |
| * WLFC_CTL_TYPE_MAC_OPEN |
| * WLFC_CTL_TYPE_MAC_CLOSE |
| * |
| * WLFC_CTL_TYPE_INTERFACE_OPEN |
| * WLFC_CTL_TYPE_INTERFACE_CLOSE |
| * |
| * WLFC_CTL_TYPE_MACDESC_ADD |
| * WLFC_CTL_TYPE_MACDESC_DEL |
| * |
| */ |
| #define WLFC_FLAGS_XONXOFF_SIGNALS 0x0002 |
| |
| /* enable (status, fifo_credit, mac_credit) signals |
| * WLFC_CTL_TYPE_MAC_REQUEST_CREDIT |
| * WLFC_CTL_TYPE_TXSTATUS |
| * WLFC_CTL_TYPE_FIFO_CREDITBACK |
| */ |
| #define WLFC_FLAGS_CREDIT_STATUS_SIGNALS 0x0004 |
| |
| #define WLFC_FLAGS_HOST_PROPTXSTATUS_ACTIVE 0x0008 |
| #define WLFC_FLAGS_PSQ_GENERATIONFSM_ENABLE 0x0010 |
| #define WLFC_FLAGS_PSQ_ZERO_BUFFER_ENABLE 0x0020 |
| #define WLFC_FLAGS_HOST_RXRERODER_ACTIVE 0x0040 |
| #define WLFC_FLAGS_PKT_STAMP_SIGNALS 0x0080 |
| |
| #endif /* PROP_TXSTATUS */ |
| |
| #define WL_TIMBC_STATUS_AP_UNKNOWN 255 /* AP status for internal use only */ |
| |
| #define WL_DFRTS_LOGIC_OFF 0 /* Feature is disabled */ |
| #define WL_DFRTS_LOGIC_OR 1 /* OR all non-zero threshold conditions */ |
| #define WL_DFRTS_LOGIC_AND 2 /* AND all non-zero threshold conditions */ |
| |
| /* Definitions for Reliable Multicast */ |
| #define WL_RELMCAST_MAX_CLIENT 32 |
| #define WL_RELMCAST_FLAG_INBLACKLIST 1 |
| #define WL_RELMCAST_FLAG_ACTIVEACKER 2 |
| #define WL_RELMCAST_FLAG_RELMCAST 4 |
| |
| /* structures for proximity detection device role */ |
| #define WL_PROXD_MODE_DISABLE 0 |
| #define WL_PROXD_MODE_NEUTRAL 1 |
| #define WL_PROXD_MODE_INITIATOR 2 |
| #define WL_PROXD_MODE_TARGET 3 |
| #define WL_PROXD_RANDOM_WAKEUP 0x8000 |
| |
| |
| #ifdef NET_DETECT |
| #define NET_DETECT_MAX_WAKE_DATA_SIZE 2048 |
| #define NET_DETECT_MAX_PROFILES 16 |
| #define NET_DETECT_MAX_CHANNELS 50 |
| #endif /* NET_DETECT */ |
| |
| |
| /* Bit masks for radio disabled status - returned by WL_GET_RADIO */ |
| #define WL_RADIO_SW_DISABLE (1<<0) |
| #define WL_RADIO_HW_DISABLE (1<<1) |
| #define WL_RADIO_MPC_DISABLE (1<<2) |
| #define WL_RADIO_COUNTRY_DISABLE (1<<3) /* some countries don't support any channel */ |
| #define WL_RADIO_PERCORE_DISABLE (1<<4) /* Radio diable per core for DVT */ |
| |
| #define WL_SPURAVOID_OFF 0 |
| #define WL_SPURAVOID_ON1 1 |
| #define WL_SPURAVOID_ON2 2 |
| |
| |
| #define WL_4335_SPURAVOID_ON1 1 |
| #define WL_4335_SPURAVOID_ON2 2 |
| #define WL_4335_SPURAVOID_ON3 3 |
| #define WL_4335_SPURAVOID_ON4 4 |
| #define WL_4335_SPURAVOID_ON5 5 |
| #define WL_4335_SPURAVOID_ON6 6 |
| #define WL_4335_SPURAVOID_ON7 7 |
| #define WL_4335_SPURAVOID_ON8 8 |
| #define WL_4335_SPURAVOID_ON9 9 |
| |
| /* Override bit for WLC_SET_TXPWR. if set, ignore other level limits */ |
| #define WL_TXPWR_OVERRIDE (1U<<31) |
| #define WL_TXPWR_2G (1U<<30) |
| #define WL_TXPWR_5G (1U<<29) |
| #define WL_TXPWR_NEG (1U<<28) |
| |
| #define WL_TXPWR_MASK (~(0x7<<29)) |
| #define WL_TXPWR_CORE_MAX (3) |
| #define WL_TXPWR_CORE0_MASK (0x000000FF) |
| #define WL_TXPWR_CORE0_SHIFT (0) |
| #define WL_TXPWR_CORE1_MASK (0x0000FF00) |
| #define WL_TXPWR_CORE1_SHIFT (8) |
| #define WL_TXPWR_CORE2_MASK (0x00FF0000) |
| #define WL_TXPWR_CORE2_SHIFT (16) |
| |
| /* phy types (returned by WLC_GET_PHYTPE) */ |
| #define WLC_PHY_TYPE_A 0 |
| #define WLC_PHY_TYPE_B 1 |
| #define WLC_PHY_TYPE_G 2 |
| #define WLC_PHY_TYPE_N 4 |
| #define WLC_PHY_TYPE_LP 5 |
| #define WLC_PHY_TYPE_SSN 6 |
| #define WLC_PHY_TYPE_HT 7 |
| #define WLC_PHY_TYPE_LCN 8 |
| #define WLC_PHY_TYPE_LCN40 10 |
| #define WLC_PHY_TYPE_AC 11 |
| #define WLC_PHY_TYPE_LCN20 12 |
| #define WLC_PHY_TYPE_NULL 0xf |
| |
| /* Values for PM */ |
| #define PM_OFF 0 |
| #define PM_MAX 1 |
| #define PM_FAST 2 |
| #define PM_FORCE_OFF 3 /* use this bit to force PM off even bt is active */ |
| |
| #define WL_WME_CNT_VERSION 1 /* current version of wl_wme_cnt_t */ |
| |
| /* fbt_cap: FBT assoc / reassoc modes. */ |
| #define WLC_FBT_CAP_DRV_4WAY_AND_REASSOC 1 /* Driver 4-way handshake & reassoc (WLFBT). */ |
| |
| /* monitor_promisc_level bits */ |
| #define WL_MONPROMISC_PROMISC 0x0001 |
| #define WL_MONPROMISC_CTRL 0x0002 |
| #define WL_MONPROMISC_FCS 0x0004 |
| |
| /* TCP Checksum Offload defines */ |
| #define TOE_TX_CSUM_OL 0x00000001 |
| #define TOE_RX_CSUM_OL 0x00000002 |
| |
| /* Wi-Fi Display Services (WFDS) */ |
| #define WL_P2P_SOCIAL_CHANNELS_MAX WL_NUMCHANNELS |
| #define MAX_WFDS_SEEK_SVC 4 /* Max # of wfds services to seek */ |
| #define MAX_WFDS_ADVERT_SVC 4 /* Max # of wfds services to advertise */ |
| #define MAX_WFDS_SVC_NAME_LEN 200 /* maximum service_name length */ |
| #define MAX_WFDS_ADV_SVC_INFO_LEN 65000 /* maximum adv service_info length */ |
| #define P2P_WFDS_HASH_LEN 6 /* Length of a WFDS service hash */ |
| #define MAX_WFDS_SEEK_SVC_INFO_LEN 255 /* maximum seek service_info req length */ |
| #define MAX_WFDS_SEEK_SVC_NAME_LEN 200 /* maximum service_name length */ |
| |
| /* ap_isolate bitmaps */ |
| #define AP_ISOLATE_DISABLED 0x0 |
| #define AP_ISOLATE_SENDUP_ALL 0x01 |
| #define AP_ISOLATE_SENDUP_MCAST 0x02 |
| |
| /* Type values for the wl_pwrstats_t data field */ |
| #define WL_PWRSTATS_TYPE_PHY 0 /**< struct wl_pwr_phy_stats */ |
| #define WL_PWRSTATS_TYPE_SCAN 1 /**< struct wl_pwr_scan_stats */ |
| #define WL_PWRSTATS_TYPE_USB_HSIC 2 /**< struct wl_pwr_usb_hsic_stats */ |
| #define WL_PWRSTATS_TYPE_PM_AWAKE1 3 /**< struct wl_pwr_pm_awake_stats_v1 */ |
| #define WL_PWRSTATS_TYPE_CONNECTION 4 /* struct wl_pwr_connect_stats; assoc and key-exch time */ |
| #define WL_PWRSTATS_TYPE_PCIE 6 /**< struct wl_pwr_pcie_stats */ |
| #define WL_PWRSTATS_TYPE_PM_AWAKE2 7 /**< struct wl_pwr_pm_awake_stats_v2 */ |
| #define WL_PWRSTATS_TYPE_SDIO 8 /* struct wl_pwr_sdio_stats */ |
| #define WL_PWRSTATS_TYPE_MIMO_PS_METRICS 9 /* struct wl_mimo_meas_metrics_t */ |
| |
| #endif /* wlioctl_defs_h */ |