| * DMA40 DMA Controller |
| |
| Required properties: |
| - compatible: "stericsson,dma40" |
| - reg: Address range of the DMAC registers |
| - reg-names: Names of the above areas to use during resource look-up |
| - interrupt: Should contain the DMAC interrupt number |
| - #dma-cells: must be <3> |
| - memcpy-channels: Channels to be used for memcpy |
| |
| Optional properties: |
| - dma-channels: Number of channels supported by hardware - if not present |
| the driver will attempt to obtain the information from H/W |
| - disabled-channels: Channels which can not be used |
| |
| Example: |
| |
| dma: dma-controller@801C0000 { |
| compatible = "stericsson,db8500-dma40", "stericsson,dma40"; |
| reg = <0x801C0000 0x1000 0x40010000 0x800>; |
| reg-names = "base", "lcpa"; |
| interrupt-parent = <&intc>; |
| interrupts = <0 25 0x4>; |
| |
| #dma-cells = <2>; |
| memcpy-channels = <56 57 58 59 60>; |
| disabled-channels = <12>; |
| dma-channels = <8>; |
| }; |
| |
| Clients |
| Required properties: |
| - dmas: Comma separated list of dma channel requests |
| - dma-names: Names of the aforementioned requested channels |
| |
| Each dmas request consists of 4 cells: |
| 1. A phandle pointing to the DMA controller |
| 2. Device signal number, the signal line for single and burst requests |
| connected from the device to the DMA40 engine |
| 3. The DMA request line number (only when 'use fixed channel' is set) |
| 4. A 32bit mask specifying; mode, direction and endianness |
| [NB: This list will grow] |
| 0x00000001: Mode: |
| Logical channel when unset |
| Physical channel when set |
| 0x00000002: Direction: |
| Memory to Device when unset |
| Device to Memory when set |
| 0x00000004: Endianness: |
| Little endian when unset |
| Big endian when set |
| 0x00000008: Use fixed channel: |
| Use automatic channel selection when unset |
| Use DMA request line number when set |
| 0x00000010: Set channel as high priority: |
| Normal priority when unset |
| High priority when set |
| |
| Existing signal numbers for the DB8500 ASIC. Unless specified, the signals are |
| bidirectional, i.e. the same for RX and TX operations: |
| |
| 0: SPI controller 0 |
| 1: SD/MMC controller 0 (unused) |
| 2: SD/MMC controller 1 (unused) |
| 3: SD/MMC controller 2 (unused) |
| 4: I2C port 1 |
| 5: I2C port 3 |
| 6: I2C port 2 |
| 7: I2C port 4 |
| 8: Synchronous Serial Port SSP0 |
| 9: Synchronous Serial Port SSP1 |
| 10: Multi-Channel Display Engine MCDE RX |
| 11: UART port 2 |
| 12: UART port 1 |
| 13: UART port 0 |
| 14: Multirate Serial Port MSP2 |
| 15: I2C port 0 |
| 16: USB OTG in/out endpoints 7 & 15 |
| 17: USB OTG in/out endpoints 6 & 14 |
| 18: USB OTG in/out endpoints 5 & 13 |
| 19: USB OTG in/out endpoints 4 & 12 |
| 20: SLIMbus or HSI channel 0 |
| 21: SLIMbus or HSI channel 1 |
| 22: SLIMbus or HSI channel 2 |
| 23: SLIMbus or HSI channel 3 |
| 24: Multimedia DSP SXA0 |
| 25: Multimedia DSP SXA1 |
| 26: Multimedia DSP SXA2 |
| 27: Multimedia DSP SXA3 |
| 28: SD/MM controller 2 |
| 29: SD/MM controller 0 |
| 30: MSP port 1 on DB8500 v1, MSP port 3 on DB8500 v2 |
| 31: MSP port 0 or SLIMbus channel 0 |
| 32: SD/MM controller 1 |
| 33: SPI controller 2 |
| 34: i2c3 RX2 TX2 |
| 35: SPI controller 1 |
| 36: USB OTG in/out endpoints 3 & 11 |
| 37: USB OTG in/out endpoints 2 & 10 |
| 38: USB OTG in/out endpoints 1 & 9 |
| 39: USB OTG in/out endpoints 8 |
| 40: SPI controller 3 |
| 41: SD/MM controller 3 |
| 42: SD/MM controller 4 |
| 43: SD/MM controller 5 |
| 44: Multimedia DSP SXA4 |
| 45: Multimedia DSP SXA5 |
| 46: SLIMbus channel 8 or Multimedia DSP SXA6 |
| 47: SLIMbus channel 9 or Multimedia DSP SXA7 |
| 48: Crypto Accelerator 1 |
| 49: Crypto Accelerator 1 TX or Hash Accelerator 1 TX |
| 50: Hash Accelerator 1 TX |
| 51: memcpy TX (to be used by the DMA driver for memcpy operations) |
| 52: SLIMbus or HSI channel 4 |
| 53: SLIMbus or HSI channel 5 |
| 54: SLIMbus or HSI channel 6 |
| 55: SLIMbus or HSI channel 7 |
| 56: memcpy (to be used by the DMA driver for memcpy operations) |
| 57: memcpy (to be used by the DMA driver for memcpy operations) |
| 58: memcpy (to be used by the DMA driver for memcpy operations) |
| 59: memcpy (to be used by the DMA driver for memcpy operations) |
| 60: memcpy (to be used by the DMA driver for memcpy operations) |
| 61: Crypto Accelerator 0 |
| 62: Crypto Accelerator 0 TX or Hash Accelerator 0 TX |
| 63: Hash Accelerator 0 TX |
| |
| Example: |
| |
| uart@80120000 { |
| compatible = "arm,pl011", "arm,primecell"; |
| reg = <0x80120000 0x1000>; |
| interrupts = <0 11 0x4>; |
| |
| dmas = <&dma 13 0 0x2>, /* Logical - DevToMem */ |
| <&dma 13 0 0x0>; /* Logical - MemToDev */ |
| dma-names = "rx", "rx"; |
| |
| }; |
