Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.txt - linux-imx - Git at Google

 Qualcomm MSM8996 TLMM block

 This binding describes the Top Level Mode Multiplexer block found in the
 MSM8996 platform.

 - compatible:
 	Usage: required
 	Value type: <string>
 	Definition: must be "qcom,msm8996-pinctrl"

 - reg:
 	Usage: required
 	Value type: <prop-encoded-array>
 	Definition: the base address and size of the TLMM register space.

 - interrupts:
 	Usage: required
 	Value type: <prop-encoded-array>
 	Definition: should specify the TLMM summary IRQ.

 - interrupt-controller:
 	Usage: required
 	Value type: <none>
 	Definition: identifies this node as an interrupt controller

 - #interrupt-cells:
 	Usage: required
 	Value type: <u32>
 	Definition: must be 2. Specifying the pin number and flags, as defined
 		    in <dt-bindings/interrupt-controller/irq.h>

 - gpio-controller:
 	Usage: required
 	Value type: <none>
 	Definition: identifies this node as a gpio controller

 - #gpio-cells:
 	Usage: required
 	Value type: <u32>
 	Definition: must be 2. Specifying the pin number and flags, as defined
 		    in <dt-bindings/gpio/gpio.h>

 Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
 a general description of GPIO and interrupt bindings.

 Please refer to pinctrl-bindings.txt in this directory for details of the
 common pinctrl bindings used by client devices, including the meaning of the
 phrase "pin configuration node".

 The pin configuration nodes act as a container for an arbitrary number of
 subnodes. Each of these subnodes represents some desired configuration for a
 pin, a group, or a list of pins or groups. This configuration can include the
 mux function to select on those pin(s)/group(s), and various pin configuration
 parameters, such as pull-up, drive strength, etc.


 PIN CONFIGURATION NODES:

 The name of each subnode is not important; all subnodes should be enumerated
 and processed purely based on their content.

 Each subnode only affects those parameters that are explicitly listed. In
 other words, a subnode that lists a mux function but no pin configuration
 parameters implies no information about any pin configuration parameters.
 Similarly, a pin subnode that describes a pullup parameter implies no
 information about e.g. the mux function.


 The following generic properties as defined in pinctrl-bindings.txt are valid
 to specify in a pin configuration subnode:

 - pins:
 	Usage: required
 	Value type: <string-array>
 	Definition: List of gpio pins affected by the properties specified in
 		    this subnode.

 		    Valid pins are:
 		      gpio0-gpio149
 		        Supports mux, bias and drive-strength

 		      sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd,
 		      sdc2_data sdc1_rclk
 		        Supports bias and drive-strength

 - function:
 	Usage: required
 	Value type: <string>
 	Definition: Specify the alternative function to be configured for the
 		    specified pins. Functions are only valid for gpio pins.
 		    Valid values are:

 		    blsp_uart1, blsp_spi1, blsp_i2c1, blsp_uim1, atest_tsens,
 		    bimc_dte1, dac_calib0, blsp_spi8, blsp_uart8, blsp_uim8,
 		    qdss_cti_trig_out_b, bimc_dte0, dac_calib1, qdss_cti_trig_in_b,
 		    dac_calib2, atest_tsens2, atest_usb1, blsp_spi10, blsp_uart10,
 		    blsp_uim10, atest_bbrx1, atest_usb13, atest_bbrx0, atest_usb12,
 		    mdp_vsync, edp_lcd, blsp_i2c10, atest_gpsadc1, atest_usb11,
 		    atest_gpsadc0, edp_hot, atest_usb10, m_voc, dac_gpio, atest_char,
 		    cam_mclk, pll_bypassnl, qdss_stm7, blsp_i2c8, qdss_tracedata_b,
 		    pll_reset, qdss_stm6, qdss_stm5, qdss_stm4, atest_usb2, cci_i2c,
 		    qdss_stm3, dac_calib3, atest_usb23, atest_char3, dac_calib4,
 		    qdss_stm2, atest_usb22, atest_char2, qdss_stm1, dac_calib5,
 		    atest_usb21, atest_char1, dbg_out, qdss_stm0, dac_calib6,
 		    atest_usb20, atest_char0, dac_calib10, qdss_stm10,
 		    qdss_cti_trig_in_a, cci_timer4, blsp_spi6, blsp_uart6, blsp_uim6,
 		    blsp2_spi, qdss_stm9, qdss_cti_trig_out_a, dac_calib11,
 		    qdss_stm8, cci_timer0, qdss_stm13, dac_calib7, cci_timer1,
 		    qdss_stm12, dac_calib8, cci_timer2, blsp1_spi, qdss_stm11,
 		    dac_calib9, cci_timer3, cci_async, dac_calib12, blsp_i2c6,
 		    qdss_tracectl_a, dac_calib13, qdss_traceclk_a, dac_calib14,
 		    dac_calib15, hdmi_rcv, dac_calib16, hdmi_cec, pwr_modem,
 		    dac_calib17, hdmi_ddc, pwr_nav, dac_calib18, pwr_crypto,
 		    dac_calib19, hdmi_hot, dac_calib20, dac_calib21, pci_e0,
 		    dac_calib22, dac_calib23, dac_calib24, tsif1_sync, dac_calib25,
 		    sd_write, tsif1_error, blsp_spi2, blsp_uart2, blsp_uim2,
 		    qdss_cti, blsp_i2c2, blsp_spi3, blsp_uart3, blsp_uim3, blsp_i2c3,
 		    uim3, blsp_spi9, blsp_uart9, blsp_uim9, blsp10_spi, blsp_i2c9,
 		    blsp_spi7, blsp_uart7, blsp_uim7, qdss_tracedata_a, blsp_i2c7,
 		    qua_mi2s, gcc_gp1_clk_a, ssc_irq, uim4, blsp_spi11, blsp_uart11,
 		    blsp_uim11, gcc_gp2_clk_a, gcc_gp3_clk_a, blsp_i2c11, cri_trng0,
 		    cri_trng1, cri_trng, qdss_stm18, pri_mi2s, qdss_stm17, blsp_spi4,
 		    blsp_uart4, blsp_uim4, qdss_stm16, qdss_stm15, blsp_i2c4,
 		    qdss_stm14, dac_calib26, spkr_i2s, audio_ref, lpass_slimbus,
 		    isense_dbg, tsense_pwm1, tsense_pwm2, btfm_slimbus, ter_mi2s,
 		    qdss_stm22, qdss_stm21, qdss_stm20, qdss_stm19, gcc_gp1_clk_b,
 		    sec_mi2s, blsp_spi5, blsp_uart5, blsp_uim5, gcc_gp2_clk_b,
 		    gcc_gp3_clk_b, blsp_i2c5, blsp_spi12, blsp_uart12, blsp_uim12,
 		    qdss_stm25, qdss_stm31, blsp_i2c12, qdss_stm30, qdss_stm29,
 		    tsif1_clk, qdss_stm28, tsif1_en, tsif1_data, sdc4_cmd, qdss_stm27,
 		    qdss_traceclk_b, tsif2_error, sdc43, vfr_1, qdss_stm26, tsif2_clk,
 		    sdc4_clk, qdss_stm24, tsif2_en, sdc42, qdss_stm23, qdss_tracectl_b,
 		    sd_card, tsif2_data, sdc41, tsif2_sync, sdc40, mdp_vsync_p_b,
 		    ldo_en, mdp_vsync_s_b, ldo_update, blsp11_uart_tx_b, blsp11_uart_rx_b,
 		    blsp11_i2c_sda_b, prng_rosc, blsp11_i2c_scl_b, uim2, uim1, uim_batt,
 		    pci_e2, pa_indicator, adsp_ext, ddr_bist, qdss_tracedata_11,
 		    qdss_tracedata_12, modem_tsync, nav_dr, nav_pps, pci_e1, gsm_tx,
 		    qspi_cs, ssbi2, ssbi1, mss_lte, qspi_clk, qspi0, qspi1, qspi2, qspi3,
 		    gpio

 - bias-disable:
 	Usage: optional
 	Value type: <none>
 	Definition: The specified pins should be configued as no pull.

 - bias-pull-down:
 	Usage: optional
 	Value type: <none>
 	Definition: The specified pins should be configued as pull down.

 - bias-pull-up:
 	Usage: optional
 	Value type: <none>
 	Definition: The specified pins should be configued as pull up.

 - output-high:
 	Usage: optional
 	Value type: <none>
 	Definition: The specified pins are configured in output mode, driven
 		    high.
 		    Not valid for sdc pins.

 - output-low:
 	Usage: optional
 	Value type: <none>
 	Definition: The specified pins are configured in output mode, driven
 		    low.
 		    Not valid for sdc pins.

 - drive-strength:
 	Usage: optional
 	Value type: <u32>
 	Definition: Selects the drive strength for the specified pins, in mA.
 		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16

 Example:

 	tlmm: pinctrl@01010000 {
 		compatible = "qcom,msm8996-pinctrl";
 		reg = <0x01010000 0x300000>;
 		interrupts = <0 208 0>;
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;

 		uart_console_active: uart_console_active {
 			mux {
 				pins = "gpio4", "gpio5";
 				function = "blsp_uart8";
 			};

 			config {
 				pins = "gpio4", "gpio5";
 				drive-strength = <2>;
 				bias-disable;
 			};
 		};
 	};
	Qualcomm MSM8996 TLMM block

	This binding describes the Top Level Mode Multiplexer block found in the
	MSM8996 platform.

	- compatible:
	Usage: required
	Value type: <string>
	Definition: must be "qcom,msm8996-pinctrl"

	- reg:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: the base address and size of the TLMM register space.

	- interrupts:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: should specify the TLMM summary IRQ.

	- interrupt-controller:
	Usage: required
	Value type: <none>
	Definition: identifies this node as an interrupt controller

	- #interrupt-cells:
	Usage: required
	Value type: <u32>
	Definition: must be 2. Specifying the pin number and flags, as defined
	in <dt-bindings/interrupt-controller/irq.h>

	- gpio-controller:
	Usage: required
	Value type: <none>
	Definition: identifies this node as a gpio controller

	- #gpio-cells:
	Usage: required
	Value type: <u32>
	Definition: must be 2. Specifying the pin number and flags, as defined
	in <dt-bindings/gpio/gpio.h>

	Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
	a general description of GPIO and interrupt bindings.

	Please refer to pinctrl-bindings.txt in this directory for details of the
	common pinctrl bindings used by client devices, including the meaning of the
	phrase "pin configuration node".

	The pin configuration nodes act as a container for an arbitrary number of
	subnodes. Each of these subnodes represents some desired configuration for a
	pin, a group, or a list of pins or groups. This configuration can include the
	mux function to select on those pin(s)/group(s), and various pin configuration
	parameters, such as pull-up, drive strength, etc.


	PIN CONFIGURATION NODES:

	The name of each subnode is not important; all subnodes should be enumerated
	and processed purely based on their content.

	Each subnode only affects those parameters that are explicitly listed. In
	other words, a subnode that lists a mux function but no pin configuration
	parameters implies no information about any pin configuration parameters.
	Similarly, a pin subnode that describes a pullup parameter implies no
	information about e.g. the mux function.


	The following generic properties as defined in pinctrl-bindings.txt are valid
	to specify in a pin configuration subnode:

	- pins:
	Usage: required
	Value type: <string-array>
	Definition: List of gpio pins affected by the properties specified in
	this subnode.

	Valid pins are:
	gpio0-gpio149
	Supports mux, bias and drive-strength

	sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd,
	sdc2_data sdc1_rclk
	Supports bias and drive-strength

	- function:
	Usage: required
	Value type: <string>
	Definition: Specify the alternative function to be configured for the
	specified pins. Functions are only valid for gpio pins.
	Valid values are:

	blsp_uart1, blsp_spi1, blsp_i2c1, blsp_uim1, atest_tsens,
	bimc_dte1, dac_calib0, blsp_spi8, blsp_uart8, blsp_uim8,
	qdss_cti_trig_out_b, bimc_dte0, dac_calib1, qdss_cti_trig_in_b,
	dac_calib2, atest_tsens2, atest_usb1, blsp_spi10, blsp_uart10,
	blsp_uim10, atest_bbrx1, atest_usb13, atest_bbrx0, atest_usb12,
	mdp_vsync, edp_lcd, blsp_i2c10, atest_gpsadc1, atest_usb11,
	atest_gpsadc0, edp_hot, atest_usb10, m_voc, dac_gpio, atest_char,
	cam_mclk, pll_bypassnl, qdss_stm7, blsp_i2c8, qdss_tracedata_b,
	pll_reset, qdss_stm6, qdss_stm5, qdss_stm4, atest_usb2, cci_i2c,
	qdss_stm3, dac_calib3, atest_usb23, atest_char3, dac_calib4,
	qdss_stm2, atest_usb22, atest_char2, qdss_stm1, dac_calib5,
	atest_usb21, atest_char1, dbg_out, qdss_stm0, dac_calib6,
	atest_usb20, atest_char0, dac_calib10, qdss_stm10,
	qdss_cti_trig_in_a, cci_timer4, blsp_spi6, blsp_uart6, blsp_uim6,
	blsp2_spi, qdss_stm9, qdss_cti_trig_out_a, dac_calib11,
	qdss_stm8, cci_timer0, qdss_stm13, dac_calib7, cci_timer1,
	qdss_stm12, dac_calib8, cci_timer2, blsp1_spi, qdss_stm11,
	dac_calib9, cci_timer3, cci_async, dac_calib12, blsp_i2c6,
	qdss_tracectl_a, dac_calib13, qdss_traceclk_a, dac_calib14,
	dac_calib15, hdmi_rcv, dac_calib16, hdmi_cec, pwr_modem,
	dac_calib17, hdmi_ddc, pwr_nav, dac_calib18, pwr_crypto,
	dac_calib19, hdmi_hot, dac_calib20, dac_calib21, pci_e0,
	dac_calib22, dac_calib23, dac_calib24, tsif1_sync, dac_calib25,
	sd_write, tsif1_error, blsp_spi2, blsp_uart2, blsp_uim2,
	qdss_cti, blsp_i2c2, blsp_spi3, blsp_uart3, blsp_uim3, blsp_i2c3,
	uim3, blsp_spi9, blsp_uart9, blsp_uim9, blsp10_spi, blsp_i2c9,
	blsp_spi7, blsp_uart7, blsp_uim7, qdss_tracedata_a, blsp_i2c7,
	qua_mi2s, gcc_gp1_clk_a, ssc_irq, uim4, blsp_spi11, blsp_uart11,
	blsp_uim11, gcc_gp2_clk_a, gcc_gp3_clk_a, blsp_i2c11, cri_trng0,
	cri_trng1, cri_trng, qdss_stm18, pri_mi2s, qdss_stm17, blsp_spi4,
	blsp_uart4, blsp_uim4, qdss_stm16, qdss_stm15, blsp_i2c4,
	qdss_stm14, dac_calib26, spkr_i2s, audio_ref, lpass_slimbus,
	isense_dbg, tsense_pwm1, tsense_pwm2, btfm_slimbus, ter_mi2s,
	qdss_stm22, qdss_stm21, qdss_stm20, qdss_stm19, gcc_gp1_clk_b,
	sec_mi2s, blsp_spi5, blsp_uart5, blsp_uim5, gcc_gp2_clk_b,
	gcc_gp3_clk_b, blsp_i2c5, blsp_spi12, blsp_uart12, blsp_uim12,
	qdss_stm25, qdss_stm31, blsp_i2c12, qdss_stm30, qdss_stm29,
	tsif1_clk, qdss_stm28, tsif1_en, tsif1_data, sdc4_cmd, qdss_stm27,
	qdss_traceclk_b, tsif2_error, sdc43, vfr_1, qdss_stm26, tsif2_clk,
	sdc4_clk, qdss_stm24, tsif2_en, sdc42, qdss_stm23, qdss_tracectl_b,
	sd_card, tsif2_data, sdc41, tsif2_sync, sdc40, mdp_vsync_p_b,
	ldo_en, mdp_vsync_s_b, ldo_update, blsp11_uart_tx_b, blsp11_uart_rx_b,
	blsp11_i2c_sda_b, prng_rosc, blsp11_i2c_scl_b, uim2, uim1, uim_batt,
	pci_e2, pa_indicator, adsp_ext, ddr_bist, qdss_tracedata_11,
	qdss_tracedata_12, modem_tsync, nav_dr, nav_pps, pci_e1, gsm_tx,
	qspi_cs, ssbi2, ssbi1, mss_lte, qspi_clk, qspi0, qspi1, qspi2, qspi3,
	gpio

	- bias-disable:
	Usage: optional
	Value type: <none>
	Definition: The specified pins should be configued as no pull.

	- bias-pull-down:
	Usage: optional
	Value type: <none>
	Definition: The specified pins should be configued as pull down.

	- bias-pull-up:
	Usage: optional
	Value type: <none>
	Definition: The specified pins should be configued as pull up.

	- output-high:
	Usage: optional
	Value type: <none>
	Definition: The specified pins are configured in output mode, driven
	high.
	Not valid for sdc pins.

	- output-low:
	Usage: optional
	Value type: <none>
	Definition: The specified pins are configured in output mode, driven
	low.
	Not valid for sdc pins.

	- drive-strength:
	Usage: optional
	Value type: <u32>
	Definition: Selects the drive strength for the specified pins, in mA.
	Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16

	Example:

	tlmm: pinctrl@01010000 {
	compatible = "qcom,msm8996-pinctrl";
	reg = <0x01010000 0x300000>;
	interrupts = <0 208 0>;
	gpio-controller;
	#gpio-cells = <2>;
	interrupt-controller;
	#interrupt-cells = <2>;

	uart_console_active: uart_console_active {
	mux {
	pins = "gpio4", "gpio5";
	function = "blsp_uart8";
	};

	config {
	pins = "gpio4", "gpio5";
	drive-strength = <2>;
	bias-disable;
	};
	};
	};