| /* |
| * Copyright (c) 2016 Linaro Ltd. |
| * Copyright (c) 2016 Hisilicon Limited. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| */ |
| |
| #include "hisi_sas.h" |
| #define DRV_NAME "hisi_sas_v2_hw" |
| |
| /* global registers need init*/ |
| #define DLVRY_QUEUE_ENABLE 0x0 |
| #define IOST_BASE_ADDR_LO 0x8 |
| #define IOST_BASE_ADDR_HI 0xc |
| #define ITCT_BASE_ADDR_LO 0x10 |
| #define ITCT_BASE_ADDR_HI 0x14 |
| #define IO_BROKEN_MSG_ADDR_LO 0x18 |
| #define IO_BROKEN_MSG_ADDR_HI 0x1c |
| #define PHY_CONTEXT 0x20 |
| #define PHY_STATE 0x24 |
| #define PHY_PORT_NUM_MA 0x28 |
| #define PORT_STATE 0x2c |
| #define PORT_STATE_PHY8_PORT_NUM_OFF 16 |
| #define PORT_STATE_PHY8_PORT_NUM_MSK (0xf << PORT_STATE_PHY8_PORT_NUM_OFF) |
| #define PORT_STATE_PHY8_CONN_RATE_OFF 20 |
| #define PORT_STATE_PHY8_CONN_RATE_MSK (0xf << PORT_STATE_PHY8_CONN_RATE_OFF) |
| #define PHY_CONN_RATE 0x30 |
| #define HGC_TRANS_TASK_CNT_LIMIT 0x38 |
| #define AXI_AHB_CLK_CFG 0x3c |
| #define ITCT_CLR 0x44 |
| #define ITCT_CLR_EN_OFF 16 |
| #define ITCT_CLR_EN_MSK (0x1 << ITCT_CLR_EN_OFF) |
| #define ITCT_DEV_OFF 0 |
| #define ITCT_DEV_MSK (0x7ff << ITCT_DEV_OFF) |
| #define AXI_USER1 0x48 |
| #define AXI_USER2 0x4c |
| #define IO_SATA_BROKEN_MSG_ADDR_LO 0x58 |
| #define IO_SATA_BROKEN_MSG_ADDR_HI 0x5c |
| #define SATA_INITI_D2H_STORE_ADDR_LO 0x60 |
| #define SATA_INITI_D2H_STORE_ADDR_HI 0x64 |
| #define HGC_SAS_TX_OPEN_FAIL_RETRY_CTRL 0x84 |
| #define HGC_SAS_TXFAIL_RETRY_CTRL 0x88 |
| #define HGC_GET_ITV_TIME 0x90 |
| #define DEVICE_MSG_WORK_MODE 0x94 |
| #define OPENA_WT_CONTI_TIME 0x9c |
| #define I_T_NEXUS_LOSS_TIME 0xa0 |
| #define MAX_CON_TIME_LIMIT_TIME 0xa4 |
| #define BUS_INACTIVE_LIMIT_TIME 0xa8 |
| #define REJECT_TO_OPEN_LIMIT_TIME 0xac |
| #define CFG_AGING_TIME 0xbc |
| #define HGC_DFX_CFG2 0xc0 |
| #define HGC_IOMB_PROC1_STATUS 0x104 |
| #define CFG_1US_TIMER_TRSH 0xcc |
| #define HGC_INVLD_DQE_INFO 0x148 |
| #define HGC_INVLD_DQE_INFO_FB_CH0_OFF 9 |
| #define HGC_INVLD_DQE_INFO_FB_CH0_MSK (0x1 << HGC_INVLD_DQE_INFO_FB_CH0_OFF) |
| #define HGC_INVLD_DQE_INFO_FB_CH3_OFF 18 |
| #define INT_COAL_EN 0x19c |
| #define OQ_INT_COAL_TIME 0x1a0 |
| #define OQ_INT_COAL_CNT 0x1a4 |
| #define ENT_INT_COAL_TIME 0x1a8 |
| #define ENT_INT_COAL_CNT 0x1ac |
| #define OQ_INT_SRC 0x1b0 |
| #define OQ_INT_SRC_MSK 0x1b4 |
| #define ENT_INT_SRC1 0x1b8 |
| #define ENT_INT_SRC1_D2H_FIS_CH0_OFF 0 |
| #define ENT_INT_SRC1_D2H_FIS_CH0_MSK (0x1 << ENT_INT_SRC1_D2H_FIS_CH0_OFF) |
| #define ENT_INT_SRC1_D2H_FIS_CH1_OFF 8 |
| #define ENT_INT_SRC1_D2H_FIS_CH1_MSK (0x1 << ENT_INT_SRC1_D2H_FIS_CH1_OFF) |
| #define ENT_INT_SRC2 0x1bc |
| #define ENT_INT_SRC3 0x1c0 |
| #define ENT_INT_SRC3_ITC_INT_OFF 15 |
| #define ENT_INT_SRC3_ITC_INT_MSK (0x1 << ENT_INT_SRC3_ITC_INT_OFF) |
| #define ENT_INT_SRC_MSK1 0x1c4 |
| #define ENT_INT_SRC_MSK2 0x1c8 |
| #define ENT_INT_SRC_MSK3 0x1cc |
| #define ENT_INT_SRC_MSK3_ENT95_MSK_OFF 31 |
| #define ENT_INT_SRC_MSK3_ENT95_MSK_MSK (0x1 << ENT_INT_SRC_MSK3_ENT95_MSK_OFF) |
| #define SAS_ECC_INTR_MSK 0x1ec |
| #define HGC_ERR_STAT_EN 0x238 |
| #define DLVRY_Q_0_BASE_ADDR_LO 0x260 |
| #define DLVRY_Q_0_BASE_ADDR_HI 0x264 |
| #define DLVRY_Q_0_DEPTH 0x268 |
| #define DLVRY_Q_0_WR_PTR 0x26c |
| #define DLVRY_Q_0_RD_PTR 0x270 |
| #define HYPER_STREAM_ID_EN_CFG 0xc80 |
| #define OQ0_INT_SRC_MSK 0xc90 |
| #define COMPL_Q_0_BASE_ADDR_LO 0x4e0 |
| #define COMPL_Q_0_BASE_ADDR_HI 0x4e4 |
| #define COMPL_Q_0_DEPTH 0x4e8 |
| #define COMPL_Q_0_WR_PTR 0x4ec |
| #define COMPL_Q_0_RD_PTR 0x4f0 |
| |
| /* phy registers need init */ |
| #define PORT_BASE (0x2000) |
| |
| #define PHY_CFG (PORT_BASE + 0x0) |
| #define HARD_PHY_LINKRATE (PORT_BASE + 0x4) |
| #define PHY_CFG_ENA_OFF 0 |
| #define PHY_CFG_ENA_MSK (0x1 << PHY_CFG_ENA_OFF) |
| #define PHY_CFG_DC_OPT_OFF 2 |
| #define PHY_CFG_DC_OPT_MSK (0x1 << PHY_CFG_DC_OPT_OFF) |
| #define PROG_PHY_LINK_RATE (PORT_BASE + 0x8) |
| #define PROG_PHY_LINK_RATE_MAX_OFF 0 |
| #define PROG_PHY_LINK_RATE_MAX_MSK (0xff << PROG_PHY_LINK_RATE_MAX_OFF) |
| #define PHY_CTRL (PORT_BASE + 0x14) |
| #define PHY_CTRL_RESET_OFF 0 |
| #define PHY_CTRL_RESET_MSK (0x1 << PHY_CTRL_RESET_OFF) |
| #define SAS_PHY_CTRL (PORT_BASE + 0x20) |
| #define SL_CFG (PORT_BASE + 0x84) |
| #define PHY_PCN (PORT_BASE + 0x44) |
| #define SL_TOUT_CFG (PORT_BASE + 0x8c) |
| #define SL_CONTROL (PORT_BASE + 0x94) |
| #define SL_CONTROL_NOTIFY_EN_OFF 0 |
| #define SL_CONTROL_NOTIFY_EN_MSK (0x1 << SL_CONTROL_NOTIFY_EN_OFF) |
| #define SL_CONTROL_CTA_OFF 17 |
| #define SL_CONTROL_CTA_MSK (0x1 << SL_CONTROL_CTA_OFF) |
| #define TX_ID_DWORD0 (PORT_BASE + 0x9c) |
| #define TX_ID_DWORD1 (PORT_BASE + 0xa0) |
| #define TX_ID_DWORD2 (PORT_BASE + 0xa4) |
| #define TX_ID_DWORD3 (PORT_BASE + 0xa8) |
| #define TX_ID_DWORD4 (PORT_BASE + 0xaC) |
| #define TX_ID_DWORD5 (PORT_BASE + 0xb0) |
| #define TX_ID_DWORD6 (PORT_BASE + 0xb4) |
| #define TXID_AUTO (PORT_BASE + 0xb8) |
| #define TXID_AUTO_CT3_OFF 1 |
| #define TXID_AUTO_CT3_MSK (0x1 << TXID_AUTO_CT3_OFF) |
| #define RX_IDAF_DWORD0 (PORT_BASE + 0xc4) |
| #define RX_IDAF_DWORD1 (PORT_BASE + 0xc8) |
| #define RX_IDAF_DWORD2 (PORT_BASE + 0xcc) |
| #define RX_IDAF_DWORD3 (PORT_BASE + 0xd0) |
| #define RX_IDAF_DWORD4 (PORT_BASE + 0xd4) |
| #define RX_IDAF_DWORD5 (PORT_BASE + 0xd8) |
| #define RX_IDAF_DWORD6 (PORT_BASE + 0xdc) |
| #define RXOP_CHECK_CFG_H (PORT_BASE + 0xfc) |
| #define DONE_RECEIVED_TIME (PORT_BASE + 0x11c) |
| #define CHL_INT0 (PORT_BASE + 0x1b4) |
| #define CHL_INT0_HOTPLUG_TOUT_OFF 0 |
| #define CHL_INT0_HOTPLUG_TOUT_MSK (0x1 << CHL_INT0_HOTPLUG_TOUT_OFF) |
| #define CHL_INT0_SL_RX_BCST_ACK_OFF 1 |
| #define CHL_INT0_SL_RX_BCST_ACK_MSK (0x1 << CHL_INT0_SL_RX_BCST_ACK_OFF) |
| #define CHL_INT0_SL_PHY_ENABLE_OFF 2 |
| #define CHL_INT0_SL_PHY_ENABLE_MSK (0x1 << CHL_INT0_SL_PHY_ENABLE_OFF) |
| #define CHL_INT0_NOT_RDY_OFF 4 |
| #define CHL_INT0_NOT_RDY_MSK (0x1 << CHL_INT0_NOT_RDY_OFF) |
| #define CHL_INT0_PHY_RDY_OFF 5 |
| #define CHL_INT0_PHY_RDY_MSK (0x1 << CHL_INT0_PHY_RDY_OFF) |
| #define CHL_INT1 (PORT_BASE + 0x1b8) |
| #define CHL_INT1_DMAC_TX_ECC_ERR_OFF 15 |
| #define CHL_INT1_DMAC_TX_ECC_ERR_MSK (0x1 << CHL_INT1_DMAC_TX_ECC_ERR_OFF) |
| #define CHL_INT1_DMAC_RX_ECC_ERR_OFF 17 |
| #define CHL_INT1_DMAC_RX_ECC_ERR_MSK (0x1 << CHL_INT1_DMAC_RX_ECC_ERR_OFF) |
| #define CHL_INT2 (PORT_BASE + 0x1bc) |
| #define CHL_INT0_MSK (PORT_BASE + 0x1c0) |
| #define CHL_INT1_MSK (PORT_BASE + 0x1c4) |
| #define CHL_INT2_MSK (PORT_BASE + 0x1c8) |
| #define CHL_INT_COAL_EN (PORT_BASE + 0x1d0) |
| #define PHY_CTRL_RDY_MSK (PORT_BASE + 0x2b0) |
| #define PHYCTRL_NOT_RDY_MSK (PORT_BASE + 0x2b4) |
| #define PHYCTRL_DWS_RESET_MSK (PORT_BASE + 0x2b8) |
| #define PHYCTRL_PHY_ENA_MSK (PORT_BASE + 0x2bc) |
| #define SL_RX_BCAST_CHK_MSK (PORT_BASE + 0x2c0) |
| #define PHYCTRL_OOB_RESTART_MSK (PORT_BASE + 0x2c4) |
| #define DMA_TX_STATUS (PORT_BASE + 0x2d0) |
| #define DMA_TX_STATUS_BUSY_OFF 0 |
| #define DMA_TX_STATUS_BUSY_MSK (0x1 << DMA_TX_STATUS_BUSY_OFF) |
| #define DMA_RX_STATUS (PORT_BASE + 0x2e8) |
| #define DMA_RX_STATUS_BUSY_OFF 0 |
| #define DMA_RX_STATUS_BUSY_MSK (0x1 << DMA_RX_STATUS_BUSY_OFF) |
| |
| #define AXI_CFG (0x5100) |
| #define AM_CFG_MAX_TRANS (0x5010) |
| #define AM_CFG_SINGLE_PORT_MAX_TRANS (0x5014) |
| |
| /* HW dma structures */ |
| /* Delivery queue header */ |
| /* dw0 */ |
| #define CMD_HDR_ABORT_FLAG_OFF 0 |
| #define CMD_HDR_ABORT_FLAG_MSK (0x3 << CMD_HDR_ABORT_FLAG_OFF) |
| #define CMD_HDR_ABORT_DEVICE_TYPE_OFF 2 |
| #define CMD_HDR_ABORT_DEVICE_TYPE_MSK (0x1 << CMD_HDR_ABORT_DEVICE_TYPE_OFF) |
| #define CMD_HDR_RESP_REPORT_OFF 5 |
| #define CMD_HDR_RESP_REPORT_MSK (0x1 << CMD_HDR_RESP_REPORT_OFF) |
| #define CMD_HDR_TLR_CTRL_OFF 6 |
| #define CMD_HDR_TLR_CTRL_MSK (0x3 << CMD_HDR_TLR_CTRL_OFF) |
| #define CMD_HDR_PORT_OFF 18 |
| #define CMD_HDR_PORT_MSK (0xf << CMD_HDR_PORT_OFF) |
| #define CMD_HDR_PRIORITY_OFF 27 |
| #define CMD_HDR_PRIORITY_MSK (0x1 << CMD_HDR_PRIORITY_OFF) |
| #define CMD_HDR_CMD_OFF 29 |
| #define CMD_HDR_CMD_MSK (0x7 << CMD_HDR_CMD_OFF) |
| /* dw1 */ |
| #define CMD_HDR_DIR_OFF 5 |
| #define CMD_HDR_DIR_MSK (0x3 << CMD_HDR_DIR_OFF) |
| #define CMD_HDR_RESET_OFF 7 |
| #define CMD_HDR_RESET_MSK (0x1 << CMD_HDR_RESET_OFF) |
| #define CMD_HDR_VDTL_OFF 10 |
| #define CMD_HDR_VDTL_MSK (0x1 << CMD_HDR_VDTL_OFF) |
| #define CMD_HDR_FRAME_TYPE_OFF 11 |
| #define CMD_HDR_FRAME_TYPE_MSK (0x1f << CMD_HDR_FRAME_TYPE_OFF) |
| #define CMD_HDR_DEV_ID_OFF 16 |
| #define CMD_HDR_DEV_ID_MSK (0xffff << CMD_HDR_DEV_ID_OFF) |
| /* dw2 */ |
| #define CMD_HDR_CFL_OFF 0 |
| #define CMD_HDR_CFL_MSK (0x1ff << CMD_HDR_CFL_OFF) |
| #define CMD_HDR_NCQ_TAG_OFF 10 |
| #define CMD_HDR_NCQ_TAG_MSK (0x1f << CMD_HDR_NCQ_TAG_OFF) |
| #define CMD_HDR_MRFL_OFF 15 |
| #define CMD_HDR_MRFL_MSK (0x1ff << CMD_HDR_MRFL_OFF) |
| #define CMD_HDR_SG_MOD_OFF 24 |
| #define CMD_HDR_SG_MOD_MSK (0x3 << CMD_HDR_SG_MOD_OFF) |
| #define CMD_HDR_FIRST_BURST_OFF 26 |
| #define CMD_HDR_FIRST_BURST_MSK (0x1 << CMD_HDR_SG_MOD_OFF) |
| /* dw3 */ |
| #define CMD_HDR_IPTT_OFF 0 |
| #define CMD_HDR_IPTT_MSK (0xffff << CMD_HDR_IPTT_OFF) |
| /* dw6 */ |
| #define CMD_HDR_DIF_SGL_LEN_OFF 0 |
| #define CMD_HDR_DIF_SGL_LEN_MSK (0xffff << CMD_HDR_DIF_SGL_LEN_OFF) |
| #define CMD_HDR_DATA_SGL_LEN_OFF 16 |
| #define CMD_HDR_DATA_SGL_LEN_MSK (0xffff << CMD_HDR_DATA_SGL_LEN_OFF) |
| #define CMD_HDR_ABORT_IPTT_OFF 16 |
| #define CMD_HDR_ABORT_IPTT_MSK (0xffff << CMD_HDR_ABORT_IPTT_OFF) |
| |
| /* Completion header */ |
| /* dw0 */ |
| #define CMPLT_HDR_RSPNS_XFRD_OFF 10 |
| #define CMPLT_HDR_RSPNS_XFRD_MSK (0x1 << CMPLT_HDR_RSPNS_XFRD_OFF) |
| #define CMPLT_HDR_ERX_OFF 12 |
| #define CMPLT_HDR_ERX_MSK (0x1 << CMPLT_HDR_ERX_OFF) |
| #define CMPLT_HDR_ABORT_STAT_OFF 13 |
| #define CMPLT_HDR_ABORT_STAT_MSK (0x7 << CMPLT_HDR_ABORT_STAT_OFF) |
| /* abort_stat */ |
| #define STAT_IO_NOT_VALID 0x1 |
| #define STAT_IO_NO_DEVICE 0x2 |
| #define STAT_IO_COMPLETE 0x3 |
| #define STAT_IO_ABORTED 0x4 |
| /* dw1 */ |
| #define CMPLT_HDR_IPTT_OFF 0 |
| #define CMPLT_HDR_IPTT_MSK (0xffff << CMPLT_HDR_IPTT_OFF) |
| #define CMPLT_HDR_DEV_ID_OFF 16 |
| #define CMPLT_HDR_DEV_ID_MSK (0xffff << CMPLT_HDR_DEV_ID_OFF) |
| |
| /* ITCT header */ |
| /* qw0 */ |
| #define ITCT_HDR_DEV_TYPE_OFF 0 |
| #define ITCT_HDR_DEV_TYPE_MSK (0x3 << ITCT_HDR_DEV_TYPE_OFF) |
| #define ITCT_HDR_VALID_OFF 2 |
| #define ITCT_HDR_VALID_MSK (0x1 << ITCT_HDR_VALID_OFF) |
| #define ITCT_HDR_MCR_OFF 5 |
| #define ITCT_HDR_MCR_MSK (0xf << ITCT_HDR_MCR_OFF) |
| #define ITCT_HDR_VLN_OFF 9 |
| #define ITCT_HDR_VLN_MSK (0xf << ITCT_HDR_VLN_OFF) |
| #define ITCT_HDR_PORT_ID_OFF 28 |
| #define ITCT_HDR_PORT_ID_MSK (0xf << ITCT_HDR_PORT_ID_OFF) |
| /* qw2 */ |
| #define ITCT_HDR_INLT_OFF 0 |
| #define ITCT_HDR_INLT_MSK (0xffffULL << ITCT_HDR_INLT_OFF) |
| #define ITCT_HDR_BITLT_OFF 16 |
| #define ITCT_HDR_BITLT_MSK (0xffffULL << ITCT_HDR_BITLT_OFF) |
| #define ITCT_HDR_MCTLT_OFF 32 |
| #define ITCT_HDR_MCTLT_MSK (0xffffULL << ITCT_HDR_MCTLT_OFF) |
| #define ITCT_HDR_RTOLT_OFF 48 |
| #define ITCT_HDR_RTOLT_MSK (0xffffULL << ITCT_HDR_RTOLT_OFF) |
| |
| struct hisi_sas_complete_v2_hdr { |
| __le32 dw0; |
| __le32 dw1; |
| __le32 act; |
| __le32 dw3; |
| }; |
| |
| struct hisi_sas_err_record_v2 { |
| /* dw0 */ |
| __le32 trans_tx_fail_type; |
| |
| /* dw1 */ |
| __le32 trans_rx_fail_type; |
| |
| /* dw2 */ |
| __le16 dma_tx_err_type; |
| __le16 sipc_rx_err_type; |
| |
| /* dw3 */ |
| __le32 dma_rx_err_type; |
| }; |
| |
| enum { |
| HISI_SAS_PHY_PHY_UPDOWN, |
| HISI_SAS_PHY_CHNL_INT, |
| HISI_SAS_PHY_INT_NR |
| }; |
| |
| enum { |
| TRANS_TX_FAIL_BASE = 0x0, /* dw0 */ |
| TRANS_RX_FAIL_BASE = 0x100, /* dw1 */ |
| DMA_TX_ERR_BASE = 0x200, /* dw2 bit 15-0 */ |
| SIPC_RX_ERR_BASE = 0x300, /* dw2 bit 31-16*/ |
| DMA_RX_ERR_BASE = 0x400, /* dw3 */ |
| |
| /* trans tx*/ |
| TRANS_TX_OPEN_FAIL_WITH_IT_NEXUS_LOSS = TRANS_TX_FAIL_BASE, /* 0x0 */ |
| TRANS_TX_ERR_PHY_NOT_ENABLE, /* 0x1 */ |
| TRANS_TX_OPEN_CNX_ERR_WRONG_DESTINATION, /* 0x2 */ |
| TRANS_TX_OPEN_CNX_ERR_ZONE_VIOLATION, /* 0x3 */ |
| TRANS_TX_OPEN_CNX_ERR_BY_OTHER, /* 0x4 */ |
| RESERVED0, /* 0x5 */ |
| TRANS_TX_OPEN_CNX_ERR_AIP_TIMEOUT, /* 0x6 */ |
| TRANS_TX_OPEN_CNX_ERR_STP_RESOURCES_BUSY, /* 0x7 */ |
| TRANS_TX_OPEN_CNX_ERR_PROTOCOL_NOT_SUPPORTED, /* 0x8 */ |
| TRANS_TX_OPEN_CNX_ERR_CONNECTION_RATE_NOT_SUPPORTED, /* 0x9 */ |
| TRANS_TX_OPEN_CNX_ERR_BAD_DESTINATION, /* 0xa */ |
| TRANS_TX_OPEN_CNX_ERR_BREAK_RCVD, /* 0xb */ |
| TRANS_TX_OPEN_CNX_ERR_LOW_PHY_POWER, /* 0xc */ |
| TRANS_TX_OPEN_CNX_ERR_PATHWAY_BLOCKED, /* 0xd */ |
| TRANS_TX_OPEN_CNX_ERR_OPEN_TIMEOUT, /* 0xe */ |
| TRANS_TX_OPEN_CNX_ERR_NO_DESTINATION, /* 0xf */ |
| TRANS_TX_OPEN_RETRY_ERR_THRESHOLD_REACHED, /* 0x10 */ |
| TRANS_TX_ERR_FRAME_TXED, /* 0x11 */ |
| TRANS_TX_ERR_WITH_BREAK_TIMEOUT, /* 0x12 */ |
| TRANS_TX_ERR_WITH_BREAK_REQUEST, /* 0x13 */ |
| TRANS_TX_ERR_WITH_BREAK_RECEVIED, /* 0x14 */ |
| TRANS_TX_ERR_WITH_CLOSE_TIMEOUT, /* 0x15 */ |
| TRANS_TX_ERR_WITH_CLOSE_NORMAL, /* 0x16 for ssp*/ |
| TRANS_TX_ERR_WITH_CLOSE_PHYDISALE, /* 0x17 */ |
| TRANS_TX_ERR_WITH_CLOSE_DWS_TIMEOUT, /* 0x18 */ |
| TRANS_TX_ERR_WITH_CLOSE_COMINIT, /* 0x19 */ |
| TRANS_TX_ERR_WITH_NAK_RECEVIED, /* 0x1a for ssp*/ |
| TRANS_TX_ERR_WITH_ACK_NAK_TIMEOUT, /* 0x1b for ssp*/ |
| /*IO_TX_ERR_WITH_R_ERR_RECEVIED, [> 0x1b for sata/stp<] */ |
| TRANS_TX_ERR_WITH_CREDIT_TIMEOUT, /* 0x1c for ssp */ |
| /*IO_RX_ERR_WITH_SATA_DEVICE_LOST 0x1c for sata/stp */ |
| TRANS_TX_ERR_WITH_IPTT_CONFLICT, /* 0x1d for ssp/smp */ |
| TRANS_TX_ERR_WITH_OPEN_BY_DES_OR_OTHERS, /* 0x1e */ |
| /*IO_TX_ERR_WITH_SYNC_RXD, [> 0x1e <] for sata/stp */ |
| TRANS_TX_ERR_WITH_WAIT_RECV_TIMEOUT, /* 0x1f for sata/stp */ |
| |
| /* trans rx */ |
| TRANS_RX_ERR_WITH_RXFRAME_CRC_ERR = TRANS_RX_FAIL_BASE, /* 0x100 */ |
| TRANS_RX_ERR_WITH_RXFIS_8B10B_DISP_ERR, /* 0x101 for sata/stp */ |
| TRANS_RX_ERR_WITH_RXFRAME_HAVE_ERRPRM, /* 0x102 for ssp/smp */ |
| /*IO_ERR_WITH_RXFIS_8B10B_CODE_ERR, [> 0x102 <] for sata/stp */ |
| TRANS_RX_ERR_WITH_RXFIS_DECODE_ERROR, /* 0x103 for sata/stp */ |
| TRANS_RX_ERR_WITH_RXFIS_CRC_ERR, /* 0x104 for sata/stp */ |
| TRANS_RX_ERR_WITH_RXFRAME_LENGTH_OVERRUN, /* 0x105 for smp */ |
| /*IO_ERR_WITH_RXFIS_TX SYNCP, [> 0x105 <] for sata/stp */ |
| TRANS_RX_ERR_WITH_RXFIS_RX_SYNCP, /* 0x106 for sata/stp*/ |
| TRANS_RX_ERR_WITH_LINK_BUF_OVERRUN, /* 0x107 */ |
| TRANS_RX_ERR_WITH_BREAK_TIMEOUT, /* 0x108 */ |
| TRANS_RX_ERR_WITH_BREAK_REQUEST, /* 0x109 */ |
| TRANS_RX_ERR_WITH_BREAK_RECEVIED, /* 0x10a */ |
| RESERVED1, /* 0x10b */ |
| TRANS_RX_ERR_WITH_CLOSE_NORMAL, /* 0x10c */ |
| TRANS_RX_ERR_WITH_CLOSE_PHY_DISABLE, /* 0x10d */ |
| TRANS_RX_ERR_WITH_CLOSE_DWS_TIMEOUT, /* 0x10e */ |
| TRANS_RX_ERR_WITH_CLOSE_COMINIT, /* 0x10f */ |
| TRANS_RX_ERR_WITH_DATA_LEN0, /* 0x110 for ssp/smp */ |
| TRANS_RX_ERR_WITH_BAD_HASH, /* 0x111 for ssp */ |
| /*IO_RX_ERR_WITH_FIS_TOO_SHORT, [> 0x111 <] for sata/stp */ |
| TRANS_RX_XRDY_WLEN_ZERO_ERR, /* 0x112 for ssp*/ |
| /*IO_RX_ERR_WITH_FIS_TOO_LONG, [> 0x112 <] for sata/stp */ |
| TRANS_RX_SSP_FRM_LEN_ERR, /* 0x113 for ssp */ |
| /*IO_RX_ERR_WITH_SATA_DEVICE_LOST, [> 0x113 <] for sata */ |
| RESERVED2, /* 0x114 */ |
| RESERVED3, /* 0x115 */ |
| RESERVED4, /* 0x116 */ |
| RESERVED5, /* 0x117 */ |
| TRANS_RX_ERR_WITH_BAD_FRM_TYPE, /* 0x118 */ |
| TRANS_RX_SMP_FRM_LEN_ERR, /* 0x119 */ |
| TRANS_RX_SMP_RESP_TIMEOUT_ERR, /* 0x11a */ |
| RESERVED6, /* 0x11b */ |
| RESERVED7, /* 0x11c */ |
| RESERVED8, /* 0x11d */ |
| RESERVED9, /* 0x11e */ |
| TRANS_RX_R_ERR, /* 0x11f */ |
| |
| /* dma tx */ |
| DMA_TX_DIF_CRC_ERR = DMA_TX_ERR_BASE, /* 0x200 */ |
| DMA_TX_DIF_APP_ERR, /* 0x201 */ |
| DMA_TX_DIF_RPP_ERR, /* 0x202 */ |
| DMA_TX_DATA_SGL_OVERFLOW, /* 0x203 */ |
| DMA_TX_DIF_SGL_OVERFLOW, /* 0x204 */ |
| DMA_TX_UNEXP_XFER_ERR, /* 0x205 */ |
| DMA_TX_UNEXP_RETRANS_ERR, /* 0x206 */ |
| DMA_TX_XFER_LEN_OVERFLOW, /* 0x207 */ |
| DMA_TX_XFER_OFFSET_ERR, /* 0x208 */ |
| DMA_TX_RAM_ECC_ERR, /* 0x209 */ |
| DMA_TX_DIF_LEN_ALIGN_ERR, /* 0x20a */ |
| |
| /* sipc rx */ |
| SIPC_RX_FIS_STATUS_ERR_BIT_VLD = SIPC_RX_ERR_BASE, /* 0x300 */ |
| SIPC_RX_PIO_WRSETUP_STATUS_DRQ_ERR, /* 0x301 */ |
| SIPC_RX_FIS_STATUS_BSY_BIT_ERR, /* 0x302 */ |
| SIPC_RX_WRSETUP_LEN_ODD_ERR, /* 0x303 */ |
| SIPC_RX_WRSETUP_LEN_ZERO_ERR, /* 0x304 */ |
| SIPC_RX_WRDATA_LEN_NOT_MATCH_ERR, /* 0x305 */ |
| SIPC_RX_NCQ_WRSETUP_OFFSET_ERR, /* 0x306 */ |
| SIPC_RX_NCQ_WRSETUP_AUTO_ACTIVE_ERR, /* 0x307 */ |
| SIPC_RX_SATA_UNEXP_FIS_ERR, /* 0x308 */ |
| SIPC_RX_WRSETUP_ESTATUS_ERR, /* 0x309 */ |
| SIPC_RX_DATA_UNDERFLOW_ERR, /* 0x30a */ |
| |
| /* dma rx */ |
| DMA_RX_DIF_CRC_ERR = DMA_RX_ERR_BASE, /* 0x400 */ |
| DMA_RX_DIF_APP_ERR, /* 0x401 */ |
| DMA_RX_DIF_RPP_ERR, /* 0x402 */ |
| DMA_RX_DATA_SGL_OVERFLOW, /* 0x403 */ |
| DMA_RX_DIF_SGL_OVERFLOW, /* 0x404 */ |
| DMA_RX_DATA_LEN_OVERFLOW, /* 0x405 */ |
| DMA_RX_DATA_LEN_UNDERFLOW, /* 0x406 */ |
| DMA_RX_DATA_OFFSET_ERR, /* 0x407 */ |
| RESERVED10, /* 0x408 */ |
| DMA_RX_SATA_FRAME_TYPE_ERR, /* 0x409 */ |
| DMA_RX_RESP_BUF_OVERFLOW, /* 0x40a */ |
| DMA_RX_UNEXP_RETRANS_RESP_ERR, /* 0x40b */ |
| DMA_RX_UNEXP_NORM_RESP_ERR, /* 0x40c */ |
| DMA_RX_UNEXP_RDFRAME_ERR, /* 0x40d */ |
| DMA_RX_PIO_DATA_LEN_ERR, /* 0x40e */ |
| DMA_RX_RDSETUP_STATUS_ERR, /* 0x40f */ |
| DMA_RX_RDSETUP_STATUS_DRQ_ERR, /* 0x410 */ |
| DMA_RX_RDSETUP_STATUS_BSY_ERR, /* 0x411 */ |
| DMA_RX_RDSETUP_LEN_ODD_ERR, /* 0x412 */ |
| DMA_RX_RDSETUP_LEN_ZERO_ERR, /* 0x413 */ |
| DMA_RX_RDSETUP_LEN_OVER_ERR, /* 0x414 */ |
| DMA_RX_RDSETUP_OFFSET_ERR, /* 0x415 */ |
| DMA_RX_RDSETUP_ACTIVE_ERR, /* 0x416 */ |
| DMA_RX_RDSETUP_ESTATUS_ERR, /* 0x417 */ |
| DMA_RX_RAM_ECC_ERR, /* 0x418 */ |
| DMA_RX_UNKNOWN_FRM_ERR, /* 0x419 */ |
| }; |
| |
| #define HISI_SAS_COMMAND_ENTRIES_V2_HW 4096 |
| |
| #define DIR_NO_DATA 0 |
| #define DIR_TO_INI 1 |
| #define DIR_TO_DEVICE 2 |
| #define DIR_RESERVED 3 |
| |
| #define SATA_PROTOCOL_NONDATA 0x1 |
| #define SATA_PROTOCOL_PIO 0x2 |
| #define SATA_PROTOCOL_DMA 0x4 |
| #define SATA_PROTOCOL_FPDMA 0x8 |
| #define SATA_PROTOCOL_ATAPI 0x10 |
| |
| static u32 hisi_sas_read32(struct hisi_hba *hisi_hba, u32 off) |
| { |
| void __iomem *regs = hisi_hba->regs + off; |
| |
| return readl(regs); |
| } |
| |
| static u32 hisi_sas_read32_relaxed(struct hisi_hba *hisi_hba, u32 off) |
| { |
| void __iomem *regs = hisi_hba->regs + off; |
| |
| return readl_relaxed(regs); |
| } |
| |
| static void hisi_sas_write32(struct hisi_hba *hisi_hba, u32 off, u32 val) |
| { |
| void __iomem *regs = hisi_hba->regs + off; |
| |
| writel(val, regs); |
| } |
| |
| static void hisi_sas_phy_write32(struct hisi_hba *hisi_hba, int phy_no, |
| u32 off, u32 val) |
| { |
| void __iomem *regs = hisi_hba->regs + (0x400 * phy_no) + off; |
| |
| writel(val, regs); |
| } |
| |
| static u32 hisi_sas_phy_read32(struct hisi_hba *hisi_hba, |
| int phy_no, u32 off) |
| { |
| void __iomem *regs = hisi_hba->regs + (0x400 * phy_no) + off; |
| |
| return readl(regs); |
| } |
| |
| /* This function needs to be protected from pre-emption. */ |
| static int |
| slot_index_alloc_quirk_v2_hw(struct hisi_hba *hisi_hba, int *slot_idx, |
| struct domain_device *device) |
| { |
| unsigned int index = 0; |
| void *bitmap = hisi_hba->slot_index_tags; |
| int sata_dev = dev_is_sata(device); |
| |
| while (1) { |
| index = find_next_zero_bit(bitmap, hisi_hba->slot_index_count, |
| index); |
| if (index >= hisi_hba->slot_index_count) |
| return -SAS_QUEUE_FULL; |
| /* |
| * SAS IPTT bit0 should be 1 |
| */ |
| if (sata_dev || (index & 1)) |
| break; |
| index++; |
| } |
| |
| set_bit(index, bitmap); |
| *slot_idx = index; |
| return 0; |
| } |
| |
| static struct |
| hisi_sas_device *alloc_dev_quirk_v2_hw(struct domain_device *device) |
| { |
| struct hisi_hba *hisi_hba = device->port->ha->lldd_ha; |
| struct hisi_sas_device *sas_dev = NULL; |
| int i, sata_dev = dev_is_sata(device); |
| |
| spin_lock(&hisi_hba->lock); |
| for (i = 0; i < HISI_SAS_MAX_DEVICES; i++) { |
| /* |
| * SATA device id bit0 should be 0 |
| */ |
| if (sata_dev && (i & 1)) |
| continue; |
| if (hisi_hba->devices[i].dev_type == SAS_PHY_UNUSED) { |
| hisi_hba->devices[i].device_id = i; |
| sas_dev = &hisi_hba->devices[i]; |
| sas_dev->dev_status = HISI_SAS_DEV_NORMAL; |
| sas_dev->dev_type = device->dev_type; |
| sas_dev->hisi_hba = hisi_hba; |
| sas_dev->sas_device = device; |
| break; |
| } |
| } |
| spin_unlock(&hisi_hba->lock); |
| |
| return sas_dev; |
| } |
| |
| static void config_phy_opt_mode_v2_hw(struct hisi_hba *hisi_hba, int phy_no) |
| { |
| u32 cfg = hisi_sas_phy_read32(hisi_hba, phy_no, PHY_CFG); |
| |
| cfg &= ~PHY_CFG_DC_OPT_MSK; |
| cfg |= 1 << PHY_CFG_DC_OPT_OFF; |
| hisi_sas_phy_write32(hisi_hba, phy_no, PHY_CFG, cfg); |
| } |
| |
| static void config_id_frame_v2_hw(struct hisi_hba *hisi_hba, int phy_no) |
| { |
| struct sas_identify_frame identify_frame; |
| u32 *identify_buffer; |
| |
| memset(&identify_frame, 0, sizeof(identify_frame)); |
| identify_frame.dev_type = SAS_END_DEVICE; |
| identify_frame.frame_type = 0; |
| identify_frame._un1 = 1; |
| identify_frame.initiator_bits = SAS_PROTOCOL_ALL; |
| identify_frame.target_bits = SAS_PROTOCOL_NONE; |
| memcpy(&identify_frame._un4_11[0], hisi_hba->sas_addr, SAS_ADDR_SIZE); |
| memcpy(&identify_frame.sas_addr[0], hisi_hba->sas_addr, SAS_ADDR_SIZE); |
| identify_frame.phy_id = phy_no; |
| identify_buffer = (u32 *)(&identify_frame); |
| |
| hisi_sas_phy_write32(hisi_hba, phy_no, TX_ID_DWORD0, |
| __swab32(identify_buffer[0])); |
| hisi_sas_phy_write32(hisi_hba, phy_no, TX_ID_DWORD1, |
| __swab32(identify_buffer[1])); |
| hisi_sas_phy_write32(hisi_hba, phy_no, TX_ID_DWORD2, |
| __swab32(identify_buffer[2])); |
| hisi_sas_phy_write32(hisi_hba, phy_no, TX_ID_DWORD3, |
| __swab32(identify_buffer[3])); |
| hisi_sas_phy_write32(hisi_hba, phy_no, TX_ID_DWORD4, |
| __swab32(identify_buffer[4])); |
| hisi_sas_phy_write32(hisi_hba, phy_no, TX_ID_DWORD5, |
| __swab32(identify_buffer[5])); |
| } |
| |
| static void setup_itct_v2_hw(struct hisi_hba *hisi_hba, |
| struct hisi_sas_device *sas_dev) |
| { |
| struct domain_device *device = sas_dev->sas_device; |
| struct device *dev = &hisi_hba->pdev->dev; |
| u64 qw0, device_id = sas_dev->device_id; |
| struct hisi_sas_itct *itct = &hisi_hba->itct[device_id]; |
| struct domain_device *parent_dev = device->parent; |
| struct hisi_sas_port *port = device->port->lldd_port; |
| |
| memset(itct, 0, sizeof(*itct)); |
| |
| /* qw0 */ |
| qw0 = 0; |
| switch (sas_dev->dev_type) { |
| case SAS_END_DEVICE: |
| case SAS_EDGE_EXPANDER_DEVICE: |
| case SAS_FANOUT_EXPANDER_DEVICE: |
| qw0 = HISI_SAS_DEV_TYPE_SSP << ITCT_HDR_DEV_TYPE_OFF; |
| break; |
| case SAS_SATA_DEV: |
| case SAS_SATA_PENDING: |
| if (parent_dev && DEV_IS_EXPANDER(parent_dev->dev_type)) |
| qw0 = HISI_SAS_DEV_TYPE_STP << ITCT_HDR_DEV_TYPE_OFF; |
| else |
| qw0 = HISI_SAS_DEV_TYPE_SATA << ITCT_HDR_DEV_TYPE_OFF; |
| break; |
| default: |
| dev_warn(dev, "setup itct: unsupported dev type (%d)\n", |
| sas_dev->dev_type); |
| } |
| |
| qw0 |= ((1 << ITCT_HDR_VALID_OFF) | |
| (device->linkrate << ITCT_HDR_MCR_OFF) | |
| (1 << ITCT_HDR_VLN_OFF) | |
| (port->id << ITCT_HDR_PORT_ID_OFF)); |
| itct->qw0 = cpu_to_le64(qw0); |
| |
| /* qw1 */ |
| memcpy(&itct->sas_addr, device->sas_addr, SAS_ADDR_SIZE); |
| itct->sas_addr = __swab64(itct->sas_addr); |
| |
| /* qw2 */ |
| if (!dev_is_sata(device)) |
| itct->qw2 = cpu_to_le64((500ULL << ITCT_HDR_INLT_OFF) | |
| (0x1ULL << ITCT_HDR_BITLT_OFF) | |
| (0x32ULL << ITCT_HDR_MCTLT_OFF) | |
| (0x1ULL << ITCT_HDR_RTOLT_OFF)); |
| } |
| |
| static void free_device_v2_hw(struct hisi_hba *hisi_hba, |
| struct hisi_sas_device *sas_dev) |
| { |
| u64 qw0, dev_id = sas_dev->device_id; |
| struct device *dev = &hisi_hba->pdev->dev; |
| struct hisi_sas_itct *itct = &hisi_hba->itct[dev_id]; |
| u32 reg_val = hisi_sas_read32(hisi_hba, ENT_INT_SRC3); |
| int i; |
| |
| /* clear the itct interrupt state */ |
| if (ENT_INT_SRC3_ITC_INT_MSK & reg_val) |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC3, |
| ENT_INT_SRC3_ITC_INT_MSK); |
| |
| /* clear the itct int*/ |
| for (i = 0; i < 2; i++) { |
| /* clear the itct table*/ |
| reg_val = hisi_sas_read32(hisi_hba, ITCT_CLR); |
| reg_val |= ITCT_CLR_EN_MSK | (dev_id & ITCT_DEV_MSK); |
| hisi_sas_write32(hisi_hba, ITCT_CLR, reg_val); |
| |
| udelay(10); |
| reg_val = hisi_sas_read32(hisi_hba, ENT_INT_SRC3); |
| if (ENT_INT_SRC3_ITC_INT_MSK & reg_val) { |
| dev_dbg(dev, "got clear ITCT done interrupt\n"); |
| |
| /* invalid the itct state*/ |
| qw0 = cpu_to_le64(itct->qw0); |
| qw0 &= ~(1 << ITCT_HDR_VALID_OFF); |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC3, |
| ENT_INT_SRC3_ITC_INT_MSK); |
| hisi_hba->devices[dev_id].dev_type = SAS_PHY_UNUSED; |
| hisi_hba->devices[dev_id].dev_status = HISI_SAS_DEV_NORMAL; |
| |
| /* clear the itct */ |
| hisi_sas_write32(hisi_hba, ITCT_CLR, 0); |
| dev_dbg(dev, "clear ITCT ok\n"); |
| break; |
| } |
| } |
| } |
| |
| static int reset_hw_v2_hw(struct hisi_hba *hisi_hba) |
| { |
| int i, reset_val; |
| u32 val; |
| unsigned long end_time; |
| struct device *dev = &hisi_hba->pdev->dev; |
| |
| /* The mask needs to be set depending on the number of phys */ |
| if (hisi_hba->n_phy == 9) |
| reset_val = 0x1fffff; |
| else |
| reset_val = 0x7ffff; |
| |
| hisi_sas_write32(hisi_hba, DLVRY_QUEUE_ENABLE, 0); |
| |
| /* Disable all of the PHYs */ |
| for (i = 0; i < hisi_hba->n_phy; i++) { |
| u32 phy_cfg = hisi_sas_phy_read32(hisi_hba, i, PHY_CFG); |
| |
| phy_cfg &= ~PHY_CTRL_RESET_MSK; |
| hisi_sas_phy_write32(hisi_hba, i, PHY_CFG, phy_cfg); |
| } |
| udelay(50); |
| |
| /* Ensure DMA tx & rx idle */ |
| for (i = 0; i < hisi_hba->n_phy; i++) { |
| u32 dma_tx_status, dma_rx_status; |
| |
| end_time = jiffies + msecs_to_jiffies(1000); |
| |
| while (1) { |
| dma_tx_status = hisi_sas_phy_read32(hisi_hba, i, |
| DMA_TX_STATUS); |
| dma_rx_status = hisi_sas_phy_read32(hisi_hba, i, |
| DMA_RX_STATUS); |
| |
| if (!(dma_tx_status & DMA_TX_STATUS_BUSY_MSK) && |
| !(dma_rx_status & DMA_RX_STATUS_BUSY_MSK)) |
| break; |
| |
| msleep(20); |
| if (time_after(jiffies, end_time)) |
| return -EIO; |
| } |
| } |
| |
| /* Ensure axi bus idle */ |
| end_time = jiffies + msecs_to_jiffies(1000); |
| while (1) { |
| u32 axi_status = |
| hisi_sas_read32(hisi_hba, AXI_CFG); |
| |
| if (axi_status == 0) |
| break; |
| |
| msleep(20); |
| if (time_after(jiffies, end_time)) |
| return -EIO; |
| } |
| |
| if (ACPI_HANDLE(dev)) { |
| acpi_status s; |
| |
| s = acpi_evaluate_object(ACPI_HANDLE(dev), "_RST", NULL, NULL); |
| if (ACPI_FAILURE(s)) { |
| dev_err(dev, "Reset failed\n"); |
| return -EIO; |
| } |
| } else if (hisi_hba->ctrl) { |
| /* reset and disable clock*/ |
| regmap_write(hisi_hba->ctrl, hisi_hba->ctrl_reset_reg, |
| reset_val); |
| regmap_write(hisi_hba->ctrl, hisi_hba->ctrl_clock_ena_reg + 4, |
| reset_val); |
| msleep(1); |
| regmap_read(hisi_hba->ctrl, hisi_hba->ctrl_reset_sts_reg, &val); |
| if (reset_val != (val & reset_val)) { |
| dev_err(dev, "SAS reset fail.\n"); |
| return -EIO; |
| } |
| |
| /* De-reset and enable clock*/ |
| regmap_write(hisi_hba->ctrl, hisi_hba->ctrl_reset_reg + 4, |
| reset_val); |
| regmap_write(hisi_hba->ctrl, hisi_hba->ctrl_clock_ena_reg, |
| reset_val); |
| msleep(1); |
| regmap_read(hisi_hba->ctrl, hisi_hba->ctrl_reset_sts_reg, |
| &val); |
| if (val & reset_val) { |
| dev_err(dev, "SAS de-reset fail.\n"); |
| return -EIO; |
| } |
| } else |
| dev_warn(dev, "no reset method\n"); |
| |
| return 0; |
| } |
| |
| static void init_reg_v2_hw(struct hisi_hba *hisi_hba) |
| { |
| struct device *dev = &hisi_hba->pdev->dev; |
| int i; |
| |
| /* Global registers init */ |
| |
| /* Deal with am-max-transmissions quirk */ |
| if (device_property_present(dev, "hip06-sas-v2-quirk-amt")) { |
| hisi_sas_write32(hisi_hba, AM_CFG_MAX_TRANS, 0x2020); |
| hisi_sas_write32(hisi_hba, AM_CFG_SINGLE_PORT_MAX_TRANS, |
| 0x2020); |
| } /* Else, use defaults -> do nothing */ |
| |
| hisi_sas_write32(hisi_hba, DLVRY_QUEUE_ENABLE, |
| (u32)((1ULL << hisi_hba->queue_count) - 1)); |
| hisi_sas_write32(hisi_hba, AXI_USER1, 0xc0000000); |
| hisi_sas_write32(hisi_hba, AXI_USER2, 0x10000); |
| hisi_sas_write32(hisi_hba, HGC_SAS_TXFAIL_RETRY_CTRL, 0x108); |
| hisi_sas_write32(hisi_hba, HGC_SAS_TX_OPEN_FAIL_RETRY_CTRL, 0x7FF); |
| hisi_sas_write32(hisi_hba, OPENA_WT_CONTI_TIME, 0x1); |
| hisi_sas_write32(hisi_hba, I_T_NEXUS_LOSS_TIME, 0x1F4); |
| hisi_sas_write32(hisi_hba, MAX_CON_TIME_LIMIT_TIME, 0x32); |
| hisi_sas_write32(hisi_hba, BUS_INACTIVE_LIMIT_TIME, 0x1); |
| hisi_sas_write32(hisi_hba, CFG_AGING_TIME, 0x1); |
| hisi_sas_write32(hisi_hba, HGC_ERR_STAT_EN, 0x1); |
| hisi_sas_write32(hisi_hba, HGC_GET_ITV_TIME, 0x1); |
| hisi_sas_write32(hisi_hba, INT_COAL_EN, 0x1); |
| hisi_sas_write32(hisi_hba, OQ_INT_COAL_TIME, 0x1); |
| hisi_sas_write32(hisi_hba, OQ_INT_COAL_CNT, 0x1); |
| hisi_sas_write32(hisi_hba, ENT_INT_COAL_TIME, 0x1); |
| hisi_sas_write32(hisi_hba, ENT_INT_COAL_CNT, 0x1); |
| hisi_sas_write32(hisi_hba, OQ_INT_SRC, 0x0); |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC1, 0xffffffff); |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC2, 0xffffffff); |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC3, 0xffffffff); |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC_MSK1, 0x7efefefe); |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC_MSK2, 0x7efefefe); |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC_MSK3, 0x7ffffffe); |
| hisi_sas_write32(hisi_hba, SAS_ECC_INTR_MSK, 0xfffff3c0); |
| for (i = 0; i < hisi_hba->queue_count; i++) |
| hisi_sas_write32(hisi_hba, OQ0_INT_SRC_MSK+0x4*i, 0); |
| |
| hisi_sas_write32(hisi_hba, AXI_AHB_CLK_CFG, 1); |
| hisi_sas_write32(hisi_hba, HYPER_STREAM_ID_EN_CFG, 1); |
| |
| for (i = 0; i < hisi_hba->n_phy; i++) { |
| hisi_sas_phy_write32(hisi_hba, i, PROG_PHY_LINK_RATE, 0x855); |
| hisi_sas_phy_write32(hisi_hba, i, SAS_PHY_CTRL, 0x30b9908); |
| hisi_sas_phy_write32(hisi_hba, i, SL_TOUT_CFG, 0x7d7d7d7d); |
| hisi_sas_phy_write32(hisi_hba, i, SL_CONTROL, 0x0); |
| hisi_sas_phy_write32(hisi_hba, i, TXID_AUTO, 0x2); |
| hisi_sas_phy_write32(hisi_hba, i, DONE_RECEIVED_TIME, 0x10); |
| hisi_sas_phy_write32(hisi_hba, i, CHL_INT0, 0xffffffff); |
| hisi_sas_phy_write32(hisi_hba, i, CHL_INT1, 0xffffffff); |
| hisi_sas_phy_write32(hisi_hba, i, CHL_INT2, 0xffffffff); |
| hisi_sas_phy_write32(hisi_hba, i, RXOP_CHECK_CFG_H, 0x1000); |
| hisi_sas_phy_write32(hisi_hba, i, CHL_INT1_MSK, 0xffffffff); |
| hisi_sas_phy_write32(hisi_hba, i, CHL_INT2_MSK, 0x8ffffbff); |
| hisi_sas_phy_write32(hisi_hba, i, SL_CFG, 0x23f801fc); |
| hisi_sas_phy_write32(hisi_hba, i, PHY_CTRL_RDY_MSK, 0x0); |
| hisi_sas_phy_write32(hisi_hba, i, PHYCTRL_NOT_RDY_MSK, 0x0); |
| hisi_sas_phy_write32(hisi_hba, i, PHYCTRL_DWS_RESET_MSK, 0x0); |
| hisi_sas_phy_write32(hisi_hba, i, PHYCTRL_PHY_ENA_MSK, 0x0); |
| hisi_sas_phy_write32(hisi_hba, i, SL_RX_BCAST_CHK_MSK, 0x0); |
| hisi_sas_phy_write32(hisi_hba, i, CHL_INT_COAL_EN, 0x0); |
| hisi_sas_phy_write32(hisi_hba, i, PHYCTRL_OOB_RESTART_MSK, 0x0); |
| hisi_sas_phy_write32(hisi_hba, i, PHY_CTRL, 0x199B694); |
| } |
| |
| for (i = 0; i < hisi_hba->queue_count; i++) { |
| /* Delivery queue */ |
| hisi_sas_write32(hisi_hba, |
| DLVRY_Q_0_BASE_ADDR_HI + (i * 0x14), |
| upper_32_bits(hisi_hba->cmd_hdr_dma[i])); |
| |
| hisi_sas_write32(hisi_hba, DLVRY_Q_0_BASE_ADDR_LO + (i * 0x14), |
| lower_32_bits(hisi_hba->cmd_hdr_dma[i])); |
| |
| hisi_sas_write32(hisi_hba, DLVRY_Q_0_DEPTH + (i * 0x14), |
| HISI_SAS_QUEUE_SLOTS); |
| |
| /* Completion queue */ |
| hisi_sas_write32(hisi_hba, COMPL_Q_0_BASE_ADDR_HI + (i * 0x14), |
| upper_32_bits(hisi_hba->complete_hdr_dma[i])); |
| |
| hisi_sas_write32(hisi_hba, COMPL_Q_0_BASE_ADDR_LO + (i * 0x14), |
| lower_32_bits(hisi_hba->complete_hdr_dma[i])); |
| |
| hisi_sas_write32(hisi_hba, COMPL_Q_0_DEPTH + (i * 0x14), |
| HISI_SAS_QUEUE_SLOTS); |
| } |
| |
| /* itct */ |
| hisi_sas_write32(hisi_hba, ITCT_BASE_ADDR_LO, |
| lower_32_bits(hisi_hba->itct_dma)); |
| |
| hisi_sas_write32(hisi_hba, ITCT_BASE_ADDR_HI, |
| upper_32_bits(hisi_hba->itct_dma)); |
| |
| /* iost */ |
| hisi_sas_write32(hisi_hba, IOST_BASE_ADDR_LO, |
| lower_32_bits(hisi_hba->iost_dma)); |
| |
| hisi_sas_write32(hisi_hba, IOST_BASE_ADDR_HI, |
| upper_32_bits(hisi_hba->iost_dma)); |
| |
| /* breakpoint */ |
| hisi_sas_write32(hisi_hba, IO_BROKEN_MSG_ADDR_LO, |
| lower_32_bits(hisi_hba->breakpoint_dma)); |
| |
| hisi_sas_write32(hisi_hba, IO_BROKEN_MSG_ADDR_HI, |
| upper_32_bits(hisi_hba->breakpoint_dma)); |
| |
| /* SATA broken msg */ |
| hisi_sas_write32(hisi_hba, IO_SATA_BROKEN_MSG_ADDR_LO, |
| lower_32_bits(hisi_hba->sata_breakpoint_dma)); |
| |
| hisi_sas_write32(hisi_hba, IO_SATA_BROKEN_MSG_ADDR_HI, |
| upper_32_bits(hisi_hba->sata_breakpoint_dma)); |
| |
| /* SATA initial fis */ |
| hisi_sas_write32(hisi_hba, SATA_INITI_D2H_STORE_ADDR_LO, |
| lower_32_bits(hisi_hba->initial_fis_dma)); |
| |
| hisi_sas_write32(hisi_hba, SATA_INITI_D2H_STORE_ADDR_HI, |
| upper_32_bits(hisi_hba->initial_fis_dma)); |
| } |
| |
| static int hw_init_v2_hw(struct hisi_hba *hisi_hba) |
| { |
| struct device *dev = &hisi_hba->pdev->dev; |
| int rc; |
| |
| rc = reset_hw_v2_hw(hisi_hba); |
| if (rc) { |
| dev_err(dev, "hisi_sas_reset_hw failed, rc=%d", rc); |
| return rc; |
| } |
| |
| msleep(100); |
| init_reg_v2_hw(hisi_hba); |
| |
| return 0; |
| } |
| |
| static void enable_phy_v2_hw(struct hisi_hba *hisi_hba, int phy_no) |
| { |
| u32 cfg = hisi_sas_phy_read32(hisi_hba, phy_no, PHY_CFG); |
| |
| cfg |= PHY_CFG_ENA_MSK; |
| hisi_sas_phy_write32(hisi_hba, phy_no, PHY_CFG, cfg); |
| } |
| |
| static void disable_phy_v2_hw(struct hisi_hba *hisi_hba, int phy_no) |
| { |
| u32 cfg = hisi_sas_phy_read32(hisi_hba, phy_no, PHY_CFG); |
| |
| cfg &= ~PHY_CFG_ENA_MSK; |
| hisi_sas_phy_write32(hisi_hba, phy_no, PHY_CFG, cfg); |
| } |
| |
| static void start_phy_v2_hw(struct hisi_hba *hisi_hba, int phy_no) |
| { |
| config_id_frame_v2_hw(hisi_hba, phy_no); |
| config_phy_opt_mode_v2_hw(hisi_hba, phy_no); |
| enable_phy_v2_hw(hisi_hba, phy_no); |
| } |
| |
| static void stop_phy_v2_hw(struct hisi_hba *hisi_hba, int phy_no) |
| { |
| disable_phy_v2_hw(hisi_hba, phy_no); |
| } |
| |
| static void phy_hard_reset_v2_hw(struct hisi_hba *hisi_hba, int phy_no) |
| { |
| stop_phy_v2_hw(hisi_hba, phy_no); |
| msleep(100); |
| start_phy_v2_hw(hisi_hba, phy_no); |
| } |
| |
| static void start_phys_v2_hw(unsigned long data) |
| { |
| struct hisi_hba *hisi_hba = (struct hisi_hba *)data; |
| int i; |
| |
| for (i = 0; i < hisi_hba->n_phy; i++) |
| start_phy_v2_hw(hisi_hba, i); |
| } |
| |
| static void phys_init_v2_hw(struct hisi_hba *hisi_hba) |
| { |
| struct timer_list *timer = &hisi_hba->timer; |
| |
| setup_timer(timer, start_phys_v2_hw, (unsigned long)hisi_hba); |
| mod_timer(timer, jiffies + HZ); |
| } |
| |
| static void sl_notify_v2_hw(struct hisi_hba *hisi_hba, int phy_no) |
| { |
| u32 sl_control; |
| |
| sl_control = hisi_sas_phy_read32(hisi_hba, phy_no, SL_CONTROL); |
| sl_control |= SL_CONTROL_NOTIFY_EN_MSK; |
| hisi_sas_phy_write32(hisi_hba, phy_no, SL_CONTROL, sl_control); |
| msleep(1); |
| sl_control = hisi_sas_phy_read32(hisi_hba, phy_no, SL_CONTROL); |
| sl_control &= ~SL_CONTROL_NOTIFY_EN_MSK; |
| hisi_sas_phy_write32(hisi_hba, phy_no, SL_CONTROL, sl_control); |
| } |
| |
| static int get_wideport_bitmap_v2_hw(struct hisi_hba *hisi_hba, int port_id) |
| { |
| int i, bitmap = 0; |
| u32 phy_port_num_ma = hisi_sas_read32(hisi_hba, PHY_PORT_NUM_MA); |
| u32 phy_state = hisi_sas_read32(hisi_hba, PHY_STATE); |
| |
| for (i = 0; i < (hisi_hba->n_phy < 9 ? hisi_hba->n_phy : 8); i++) |
| if (phy_state & 1 << i) |
| if (((phy_port_num_ma >> (i * 4)) & 0xf) == port_id) |
| bitmap |= 1 << i; |
| |
| if (hisi_hba->n_phy == 9) { |
| u32 port_state = hisi_sas_read32(hisi_hba, PORT_STATE); |
| |
| if (phy_state & 1 << 8) |
| if (((port_state & PORT_STATE_PHY8_PORT_NUM_MSK) >> |
| PORT_STATE_PHY8_PORT_NUM_OFF) == port_id) |
| bitmap |= 1 << 9; |
| } |
| |
| return bitmap; |
| } |
| |
| /** |
| * This function allocates across all queues to load balance. |
| * Slots are allocated from queues in a round-robin fashion. |
| * |
| * The callpath to this function and upto writing the write |
| * queue pointer should be safe from interruption. |
| */ |
| static int get_free_slot_v2_hw(struct hisi_hba *hisi_hba, int *q, int *s) |
| { |
| struct device *dev = &hisi_hba->pdev->dev; |
| struct hisi_sas_dq *dq; |
| u32 r, w; |
| int queue = hisi_hba->queue; |
| |
| while (1) { |
| dq = &hisi_hba->dq[queue]; |
| w = dq->wr_point; |
| r = hisi_sas_read32_relaxed(hisi_hba, |
| DLVRY_Q_0_RD_PTR + (queue * 0x14)); |
| if (r == (w+1) % HISI_SAS_QUEUE_SLOTS) { |
| queue = (queue + 1) % hisi_hba->queue_count; |
| if (queue == hisi_hba->queue) { |
| dev_warn(dev, "could not find free slot\n"); |
| return -EAGAIN; |
| } |
| continue; |
| } |
| break; |
| } |
| hisi_hba->queue = (queue + 1) % hisi_hba->queue_count; |
| *q = queue; |
| *s = w; |
| return 0; |
| } |
| |
| static void start_delivery_v2_hw(struct hisi_hba *hisi_hba) |
| { |
| int dlvry_queue = hisi_hba->slot_prep->dlvry_queue; |
| int dlvry_queue_slot = hisi_hba->slot_prep->dlvry_queue_slot; |
| struct hisi_sas_dq *dq = &hisi_hba->dq[dlvry_queue]; |
| |
| dq->wr_point = ++dlvry_queue_slot % HISI_SAS_QUEUE_SLOTS; |
| hisi_sas_write32(hisi_hba, DLVRY_Q_0_WR_PTR + (dlvry_queue * 0x14), |
| dq->wr_point); |
| } |
| |
| static int prep_prd_sge_v2_hw(struct hisi_hba *hisi_hba, |
| struct hisi_sas_slot *slot, |
| struct hisi_sas_cmd_hdr *hdr, |
| struct scatterlist *scatter, |
| int n_elem) |
| { |
| struct device *dev = &hisi_hba->pdev->dev; |
| struct scatterlist *sg; |
| int i; |
| |
| if (n_elem > HISI_SAS_SGE_PAGE_CNT) { |
| dev_err(dev, "prd err: n_elem(%d) > HISI_SAS_SGE_PAGE_CNT", |
| n_elem); |
| return -EINVAL; |
| } |
| |
| slot->sge_page = dma_pool_alloc(hisi_hba->sge_page_pool, GFP_ATOMIC, |
| &slot->sge_page_dma); |
| if (!slot->sge_page) |
| return -ENOMEM; |
| |
| for_each_sg(scatter, sg, n_elem, i) { |
| struct hisi_sas_sge *entry = &slot->sge_page->sge[i]; |
| |
| entry->addr = cpu_to_le64(sg_dma_address(sg)); |
| entry->page_ctrl_0 = entry->page_ctrl_1 = 0; |
| entry->data_len = cpu_to_le32(sg_dma_len(sg)); |
| entry->data_off = 0; |
| } |
| |
| hdr->prd_table_addr = cpu_to_le64(slot->sge_page_dma); |
| |
| hdr->sg_len = cpu_to_le32(n_elem << CMD_HDR_DATA_SGL_LEN_OFF); |
| |
| return 0; |
| } |
| |
| static int prep_smp_v2_hw(struct hisi_hba *hisi_hba, |
| struct hisi_sas_slot *slot) |
| { |
| struct sas_task *task = slot->task; |
| struct hisi_sas_cmd_hdr *hdr = slot->cmd_hdr; |
| struct domain_device *device = task->dev; |
| struct device *dev = &hisi_hba->pdev->dev; |
| struct hisi_sas_port *port = slot->port; |
| struct scatterlist *sg_req, *sg_resp; |
| struct hisi_sas_device *sas_dev = device->lldd_dev; |
| dma_addr_t req_dma_addr; |
| unsigned int req_len, resp_len; |
| int elem, rc; |
| |
| /* |
| * DMA-map SMP request, response buffers |
| */ |
| /* req */ |
| sg_req = &task->smp_task.smp_req; |
| elem = dma_map_sg(dev, sg_req, 1, DMA_TO_DEVICE); |
| if (!elem) |
| return -ENOMEM; |
| req_len = sg_dma_len(sg_req); |
| req_dma_addr = sg_dma_address(sg_req); |
| |
| /* resp */ |
| sg_resp = &task->smp_task.smp_resp; |
| elem = dma_map_sg(dev, sg_resp, 1, DMA_FROM_DEVICE); |
| if (!elem) { |
| rc = -ENOMEM; |
| goto err_out_req; |
| } |
| resp_len = sg_dma_len(sg_resp); |
| if ((req_len & 0x3) || (resp_len & 0x3)) { |
| rc = -EINVAL; |
| goto err_out_resp; |
| } |
| |
| /* create header */ |
| /* dw0 */ |
| hdr->dw0 = cpu_to_le32((port->id << CMD_HDR_PORT_OFF) | |
| (1 << CMD_HDR_PRIORITY_OFF) | /* high pri */ |
| (2 << CMD_HDR_CMD_OFF)); /* smp */ |
| |
| /* map itct entry */ |
| hdr->dw1 = cpu_to_le32((sas_dev->device_id << CMD_HDR_DEV_ID_OFF) | |
| (1 << CMD_HDR_FRAME_TYPE_OFF) | |
| (DIR_NO_DATA << CMD_HDR_DIR_OFF)); |
| |
| /* dw2 */ |
| hdr->dw2 = cpu_to_le32((((req_len - 4) / 4) << CMD_HDR_CFL_OFF) | |
| (HISI_SAS_MAX_SMP_RESP_SZ / 4 << |
| CMD_HDR_MRFL_OFF)); |
| |
| hdr->transfer_tags = cpu_to_le32(slot->idx << CMD_HDR_IPTT_OFF); |
| |
| hdr->cmd_table_addr = cpu_to_le64(req_dma_addr); |
| hdr->sts_buffer_addr = cpu_to_le64(slot->status_buffer_dma); |
| |
| return 0; |
| |
| err_out_resp: |
| dma_unmap_sg(dev, &slot->task->smp_task.smp_resp, 1, |
| DMA_FROM_DEVICE); |
| err_out_req: |
| dma_unmap_sg(dev, &slot->task->smp_task.smp_req, 1, |
| DMA_TO_DEVICE); |
| return rc; |
| } |
| |
| static int prep_ssp_v2_hw(struct hisi_hba *hisi_hba, |
| struct hisi_sas_slot *slot, int is_tmf, |
| struct hisi_sas_tmf_task *tmf) |
| { |
| struct sas_task *task = slot->task; |
| struct hisi_sas_cmd_hdr *hdr = slot->cmd_hdr; |
| struct domain_device *device = task->dev; |
| struct hisi_sas_device *sas_dev = device->lldd_dev; |
| struct hisi_sas_port *port = slot->port; |
| struct sas_ssp_task *ssp_task = &task->ssp_task; |
| struct scsi_cmnd *scsi_cmnd = ssp_task->cmd; |
| int has_data = 0, rc, priority = is_tmf; |
| u8 *buf_cmd; |
| u32 dw1 = 0, dw2 = 0; |
| |
| hdr->dw0 = cpu_to_le32((1 << CMD_HDR_RESP_REPORT_OFF) | |
| (2 << CMD_HDR_TLR_CTRL_OFF) | |
| (port->id << CMD_HDR_PORT_OFF) | |
| (priority << CMD_HDR_PRIORITY_OFF) | |
| (1 << CMD_HDR_CMD_OFF)); /* ssp */ |
| |
| dw1 = 1 << CMD_HDR_VDTL_OFF; |
| if (is_tmf) { |
| dw1 |= 2 << CMD_HDR_FRAME_TYPE_OFF; |
| dw1 |= DIR_NO_DATA << CMD_HDR_DIR_OFF; |
| } else { |
| dw1 |= 1 << CMD_HDR_FRAME_TYPE_OFF; |
| switch (scsi_cmnd->sc_data_direction) { |
| case DMA_TO_DEVICE: |
| has_data = 1; |
| dw1 |= DIR_TO_DEVICE << CMD_HDR_DIR_OFF; |
| break; |
| case DMA_FROM_DEVICE: |
| has_data = 1; |
| dw1 |= DIR_TO_INI << CMD_HDR_DIR_OFF; |
| break; |
| default: |
| dw1 &= ~CMD_HDR_DIR_MSK; |
| } |
| } |
| |
| /* map itct entry */ |
| dw1 |= sas_dev->device_id << CMD_HDR_DEV_ID_OFF; |
| hdr->dw1 = cpu_to_le32(dw1); |
| |
| dw2 = (((sizeof(struct ssp_command_iu) + sizeof(struct ssp_frame_hdr) |
| + 3) / 4) << CMD_HDR_CFL_OFF) | |
| ((HISI_SAS_MAX_SSP_RESP_SZ / 4) << CMD_HDR_MRFL_OFF) | |
| (2 << CMD_HDR_SG_MOD_OFF); |
| hdr->dw2 = cpu_to_le32(dw2); |
| |
| hdr->transfer_tags = cpu_to_le32(slot->idx); |
| |
| if (has_data) { |
| rc = prep_prd_sge_v2_hw(hisi_hba, slot, hdr, task->scatter, |
| slot->n_elem); |
| if (rc) |
| return rc; |
| } |
| |
| hdr->data_transfer_len = cpu_to_le32(task->total_xfer_len); |
| hdr->cmd_table_addr = cpu_to_le64(slot->command_table_dma); |
| hdr->sts_buffer_addr = cpu_to_le64(slot->status_buffer_dma); |
| |
| buf_cmd = slot->command_table + sizeof(struct ssp_frame_hdr); |
| |
| memcpy(buf_cmd, &task->ssp_task.LUN, 8); |
| if (!is_tmf) { |
| buf_cmd[9] = task->ssp_task.task_attr | |
| (task->ssp_task.task_prio << 3); |
| memcpy(buf_cmd + 12, task->ssp_task.cmd->cmnd, |
| task->ssp_task.cmd->cmd_len); |
| } else { |
| buf_cmd[10] = tmf->tmf; |
| switch (tmf->tmf) { |
| case TMF_ABORT_TASK: |
| case TMF_QUERY_TASK: |
| buf_cmd[12] = |
| (tmf->tag_of_task_to_be_managed >> 8) & 0xff; |
| buf_cmd[13] = |
| tmf->tag_of_task_to_be_managed & 0xff; |
| break; |
| default: |
| break; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static void sata_done_v2_hw(struct hisi_hba *hisi_hba, struct sas_task *task, |
| struct hisi_sas_slot *slot) |
| { |
| struct task_status_struct *ts = &task->task_status; |
| struct ata_task_resp *resp = (struct ata_task_resp *)ts->buf; |
| struct dev_to_host_fis *d2h = slot->status_buffer + |
| sizeof(struct hisi_sas_err_record); |
| |
| resp->frame_len = sizeof(struct dev_to_host_fis); |
| memcpy(&resp->ending_fis[0], d2h, sizeof(struct dev_to_host_fis)); |
| |
| ts->buf_valid_size = sizeof(*resp); |
| } |
| |
| /* by default, task resp is complete */ |
| static void slot_err_v2_hw(struct hisi_hba *hisi_hba, |
| struct sas_task *task, |
| struct hisi_sas_slot *slot) |
| { |
| struct task_status_struct *ts = &task->task_status; |
| struct hisi_sas_err_record_v2 *err_record = slot->status_buffer; |
| u32 trans_tx_fail_type = cpu_to_le32(err_record->trans_tx_fail_type); |
| u32 trans_rx_fail_type = cpu_to_le32(err_record->trans_rx_fail_type); |
| u16 dma_tx_err_type = cpu_to_le16(err_record->dma_tx_err_type); |
| u16 sipc_rx_err_type = cpu_to_le16(err_record->sipc_rx_err_type); |
| u32 dma_rx_err_type = cpu_to_le32(err_record->dma_rx_err_type); |
| int error = -1; |
| |
| if (dma_rx_err_type) { |
| error = ffs(dma_rx_err_type) |
| - 1 + DMA_RX_ERR_BASE; |
| } else if (sipc_rx_err_type) { |
| error = ffs(sipc_rx_err_type) |
| - 1 + SIPC_RX_ERR_BASE; |
| } else if (dma_tx_err_type) { |
| error = ffs(dma_tx_err_type) |
| - 1 + DMA_TX_ERR_BASE; |
| } else if (trans_rx_fail_type) { |
| error = ffs(trans_rx_fail_type) |
| - 1 + TRANS_RX_FAIL_BASE; |
| } else if (trans_tx_fail_type) { |
| error = ffs(trans_tx_fail_type) |
| - 1 + TRANS_TX_FAIL_BASE; |
| } |
| |
| switch (task->task_proto) { |
| case SAS_PROTOCOL_SSP: |
| { |
| switch (error) { |
| case TRANS_TX_OPEN_CNX_ERR_NO_DESTINATION: |
| { |
| ts->stat = SAS_OPEN_REJECT; |
| ts->open_rej_reason = SAS_OREJ_NO_DEST; |
| break; |
| } |
| case TRANS_TX_OPEN_CNX_ERR_PATHWAY_BLOCKED: |
| { |
| ts->stat = SAS_OPEN_REJECT; |
| ts->open_rej_reason = SAS_OREJ_PATH_BLOCKED; |
| break; |
| } |
| case TRANS_TX_OPEN_CNX_ERR_PROTOCOL_NOT_SUPPORTED: |
| { |
| ts->stat = SAS_OPEN_REJECT; |
| ts->open_rej_reason = SAS_OREJ_EPROTO; |
| break; |
| } |
| case TRANS_TX_OPEN_CNX_ERR_CONNECTION_RATE_NOT_SUPPORTED: |
| { |
| ts->stat = SAS_OPEN_REJECT; |
| ts->open_rej_reason = SAS_OREJ_CONN_RATE; |
| break; |
| } |
| case TRANS_TX_OPEN_CNX_ERR_BAD_DESTINATION: |
| { |
| ts->stat = SAS_OPEN_REJECT; |
| ts->open_rej_reason = SAS_OREJ_BAD_DEST; |
| break; |
| } |
| case TRANS_TX_OPEN_CNX_ERR_BREAK_RCVD: |
| { |
| ts->stat = SAS_OPEN_REJECT; |
| ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; |
| break; |
| } |
| case TRANS_TX_OPEN_CNX_ERR_WRONG_DESTINATION: |
| { |
| ts->stat = SAS_OPEN_REJECT; |
| ts->open_rej_reason = SAS_OREJ_WRONG_DEST; |
| break; |
| } |
| case TRANS_TX_OPEN_CNX_ERR_ZONE_VIOLATION: |
| { |
| ts->stat = SAS_OPEN_REJECT; |
| ts->open_rej_reason = SAS_OREJ_UNKNOWN; |
| break; |
| } |
| case TRANS_TX_OPEN_CNX_ERR_LOW_PHY_POWER: |
| { |
| /* not sure */ |
| ts->stat = SAS_DEV_NO_RESPONSE; |
| break; |
| } |
| case TRANS_RX_ERR_WITH_CLOSE_PHY_DISABLE: |
| { |
| ts->stat = SAS_PHY_DOWN; |
| break; |
| } |
| case TRANS_TX_OPEN_CNX_ERR_OPEN_TIMEOUT: |
| { |
| ts->stat = SAS_OPEN_TO; |
| break; |
| } |
| case DMA_RX_DATA_LEN_OVERFLOW: |
| { |
| ts->stat = SAS_DATA_OVERRUN; |
| ts->residual = 0; |
| break; |
| } |
| case DMA_RX_DATA_LEN_UNDERFLOW: |
| case SIPC_RX_DATA_UNDERFLOW_ERR: |
| { |
| ts->residual = trans_tx_fail_type; |
| ts->stat = SAS_DATA_UNDERRUN; |
| break; |
| } |
| case TRANS_TX_ERR_FRAME_TXED: |
| { |
| /* This will request a retry */ |
| ts->stat = SAS_QUEUE_FULL; |
| slot->abort = 1; |
| break; |
| } |
| case TRANS_TX_OPEN_FAIL_WITH_IT_NEXUS_LOSS: |
| case TRANS_TX_ERR_PHY_NOT_ENABLE: |
| case TRANS_TX_OPEN_CNX_ERR_BY_OTHER: |
| case TRANS_TX_OPEN_CNX_ERR_AIP_TIMEOUT: |
| case TRANS_TX_OPEN_RETRY_ERR_THRESHOLD_REACHED: |
| case TRANS_TX_ERR_WITH_BREAK_TIMEOUT: |
| case TRANS_TX_ERR_WITH_BREAK_REQUEST: |
| case TRANS_TX_ERR_WITH_BREAK_RECEVIED: |
| case TRANS_TX_ERR_WITH_CLOSE_TIMEOUT: |
| case TRANS_TX_ERR_WITH_CLOSE_NORMAL: |
| case TRANS_TX_ERR_WITH_CLOSE_DWS_TIMEOUT: |
| case TRANS_TX_ERR_WITH_CLOSE_COMINIT: |
| case TRANS_TX_ERR_WITH_NAK_RECEVIED: |
| case TRANS_TX_ERR_WITH_ACK_NAK_TIMEOUT: |
| case TRANS_TX_ERR_WITH_IPTT_CONFLICT: |
| case TRANS_TX_ERR_WITH_CREDIT_TIMEOUT: |
| case TRANS_RX_ERR_WITH_RXFRAME_CRC_ERR: |
| case TRANS_RX_ERR_WITH_RXFIS_8B10B_DISP_ERR: |
| case TRANS_RX_ERR_WITH_RXFRAME_HAVE_ERRPRM: |
| case TRANS_RX_ERR_WITH_BREAK_TIMEOUT: |
| case TRANS_RX_ERR_WITH_BREAK_REQUEST: |
| case TRANS_RX_ERR_WITH_BREAK_RECEVIED: |
| case TRANS_RX_ERR_WITH_CLOSE_NORMAL: |
| case TRANS_RX_ERR_WITH_CLOSE_DWS_TIMEOUT: |
| case TRANS_RX_ERR_WITH_CLOSE_COMINIT: |
| case TRANS_RX_ERR_WITH_DATA_LEN0: |
| case TRANS_RX_ERR_WITH_BAD_HASH: |
| case TRANS_RX_XRDY_WLEN_ZERO_ERR: |
| case TRANS_RX_SSP_FRM_LEN_ERR: |
| case TRANS_RX_ERR_WITH_BAD_FRM_TYPE: |
| case DMA_TX_UNEXP_XFER_ERR: |
| case DMA_TX_UNEXP_RETRANS_ERR: |
| case DMA_TX_XFER_LEN_OVERFLOW: |
| case DMA_TX_XFER_OFFSET_ERR: |
| case DMA_RX_DATA_OFFSET_ERR: |
| case DMA_RX_UNEXP_NORM_RESP_ERR: |
| case DMA_RX_UNEXP_RDFRAME_ERR: |
| case DMA_RX_UNKNOWN_FRM_ERR: |
| { |
| ts->stat = SAS_OPEN_REJECT; |
| ts->open_rej_reason = SAS_OREJ_UNKNOWN; |
| break; |
| } |
| default: |
| break; |
| } |
| } |
| break; |
| case SAS_PROTOCOL_SMP: |
| ts->stat = SAM_STAT_CHECK_CONDITION; |
| break; |
| |
| case SAS_PROTOCOL_SATA: |
| case SAS_PROTOCOL_STP: |
| case SAS_PROTOCOL_SATA | SAS_PROTOCOL_STP: |
| { |
| switch (error) { |
| case TRANS_TX_OPEN_CNX_ERR_LOW_PHY_POWER: |
| case TRANS_TX_OPEN_CNX_ERR_PATHWAY_BLOCKED: |
| case TRANS_TX_OPEN_CNX_ERR_NO_DESTINATION: |
| { |
| ts->resp = SAS_TASK_UNDELIVERED; |
| ts->stat = SAS_DEV_NO_RESPONSE; |
| break; |
| } |
| case TRANS_TX_OPEN_CNX_ERR_PROTOCOL_NOT_SUPPORTED: |
| case TRANS_TX_OPEN_CNX_ERR_CONNECTION_RATE_NOT_SUPPORTED: |
| case TRANS_TX_OPEN_CNX_ERR_BAD_DESTINATION: |
| case TRANS_TX_OPEN_CNX_ERR_BREAK_RCVD: |
| case TRANS_TX_OPEN_CNX_ERR_WRONG_DESTINATION: |
| case TRANS_TX_OPEN_CNX_ERR_ZONE_VIOLATION: |
| case TRANS_TX_OPEN_CNX_ERR_STP_RESOURCES_BUSY: |
| { |
| ts->stat = SAS_OPEN_REJECT; |
| break; |
| } |
| case TRANS_TX_OPEN_CNX_ERR_OPEN_TIMEOUT: |
| { |
| ts->stat = SAS_OPEN_TO; |
| break; |
| } |
| case DMA_RX_DATA_LEN_OVERFLOW: |
| { |
| ts->stat = SAS_DATA_OVERRUN; |
| break; |
| } |
| case TRANS_TX_OPEN_FAIL_WITH_IT_NEXUS_LOSS: |
| case TRANS_TX_ERR_PHY_NOT_ENABLE: |
| case TRANS_TX_OPEN_CNX_ERR_BY_OTHER: |
| case TRANS_TX_OPEN_CNX_ERR_AIP_TIMEOUT: |
| case TRANS_TX_OPEN_RETRY_ERR_THRESHOLD_REACHED: |
| case TRANS_TX_ERR_WITH_BREAK_TIMEOUT: |
| case TRANS_TX_ERR_WITH_BREAK_REQUEST: |
| case TRANS_TX_ERR_WITH_BREAK_RECEVIED: |
| case TRANS_TX_ERR_WITH_CLOSE_TIMEOUT: |
| case TRANS_TX_ERR_WITH_CLOSE_NORMAL: |
| case TRANS_TX_ERR_WITH_CLOSE_DWS_TIMEOUT: |
| case TRANS_TX_ERR_WITH_CLOSE_COMINIT: |
| case TRANS_TX_ERR_WITH_NAK_RECEVIED: |
| case TRANS_TX_ERR_WITH_ACK_NAK_TIMEOUT: |
| case TRANS_TX_ERR_WITH_CREDIT_TIMEOUT: |
| case TRANS_TX_ERR_WITH_WAIT_RECV_TIMEOUT: |
| case TRANS_RX_ERR_WITH_RXFIS_8B10B_DISP_ERR: |
| case TRANS_RX_ERR_WITH_RXFRAME_HAVE_ERRPRM: |
| case TRANS_RX_ERR_WITH_RXFIS_DECODE_ERROR: |
| case TRANS_RX_ERR_WITH_RXFIS_CRC_ERR: |
| case TRANS_RX_ERR_WITH_RXFRAME_LENGTH_OVERRUN: |
| case TRANS_RX_ERR_WITH_RXFIS_RX_SYNCP: |
| case TRANS_RX_ERR_WITH_CLOSE_NORMAL: |
| case TRANS_RX_ERR_WITH_CLOSE_PHY_DISABLE: |
| case TRANS_RX_ERR_WITH_CLOSE_DWS_TIMEOUT: |
| case TRANS_RX_ERR_WITH_CLOSE_COMINIT: |
| case TRANS_RX_ERR_WITH_DATA_LEN0: |
| case TRANS_RX_ERR_WITH_BAD_HASH: |
| case TRANS_RX_XRDY_WLEN_ZERO_ERR: |
| case TRANS_RX_SSP_FRM_LEN_ERR: |
| case SIPC_RX_FIS_STATUS_ERR_BIT_VLD: |
| case SIPC_RX_PIO_WRSETUP_STATUS_DRQ_ERR: |
| case SIPC_RX_FIS_STATUS_BSY_BIT_ERR: |
| case SIPC_RX_WRSETUP_LEN_ODD_ERR: |
| case SIPC_RX_WRSETUP_LEN_ZERO_ERR: |
| case SIPC_RX_WRDATA_LEN_NOT_MATCH_ERR: |
| case SIPC_RX_SATA_UNEXP_FIS_ERR: |
| case DMA_RX_SATA_FRAME_TYPE_ERR: |
| case DMA_RX_UNEXP_RDFRAME_ERR: |
| case DMA_RX_PIO_DATA_LEN_ERR: |
| case DMA_RX_RDSETUP_STATUS_ERR: |
| case DMA_RX_RDSETUP_STATUS_DRQ_ERR: |
| case DMA_RX_RDSETUP_STATUS_BSY_ERR: |
| case DMA_RX_RDSETUP_LEN_ODD_ERR: |
| case DMA_RX_RDSETUP_LEN_ZERO_ERR: |
| case DMA_RX_RDSETUP_LEN_OVER_ERR: |
| case DMA_RX_RDSETUP_OFFSET_ERR: |
| case DMA_RX_RDSETUP_ACTIVE_ERR: |
| case DMA_RX_RDSETUP_ESTATUS_ERR: |
| case DMA_RX_UNKNOWN_FRM_ERR: |
| { |
| ts->stat = SAS_OPEN_REJECT; |
| break; |
| } |
| default: |
| { |
| ts->stat = SAS_PROTO_RESPONSE; |
| break; |
| } |
| } |
| sata_done_v2_hw(hisi_hba, task, slot); |
| } |
| break; |
| default: |
| break; |
| } |
| } |
| |
| static int |
| slot_complete_v2_hw(struct hisi_hba *hisi_hba, struct hisi_sas_slot *slot, |
| int abort) |
| { |
| struct sas_task *task = slot->task; |
| struct hisi_sas_device *sas_dev; |
| struct device *dev = &hisi_hba->pdev->dev; |
| struct task_status_struct *ts; |
| struct domain_device *device; |
| enum exec_status sts; |
| struct hisi_sas_complete_v2_hdr *complete_queue = |
| hisi_hba->complete_hdr[slot->cmplt_queue]; |
| struct hisi_sas_complete_v2_hdr *complete_hdr = |
| &complete_queue[slot->cmplt_queue_slot]; |
| |
| if (unlikely(!task || !task->lldd_task || !task->dev)) |
| return -EINVAL; |
| |
| ts = &task->task_status; |
| device = task->dev; |
| sas_dev = device->lldd_dev; |
| |
| task->task_state_flags &= |
| ~(SAS_TASK_STATE_PENDING | SAS_TASK_AT_INITIATOR); |
| task->task_state_flags |= SAS_TASK_STATE_DONE; |
| |
| memset(ts, 0, sizeof(*ts)); |
| ts->resp = SAS_TASK_COMPLETE; |
| |
| if (unlikely(!sas_dev || abort)) { |
| if (!sas_dev) |
| dev_dbg(dev, "slot complete: port has not device\n"); |
| ts->stat = SAS_PHY_DOWN; |
| goto out; |
| } |
| |
| /* Use SAS+TMF status codes */ |
| switch ((complete_hdr->dw0 & CMPLT_HDR_ABORT_STAT_MSK) |
| >> CMPLT_HDR_ABORT_STAT_OFF) { |
| case STAT_IO_ABORTED: |
| /* this io has been aborted by abort command */ |
| ts->stat = SAS_ABORTED_TASK; |
| goto out; |
| case STAT_IO_COMPLETE: |
| /* internal abort command complete */ |
| ts->stat = TMF_RESP_FUNC_COMPLETE; |
| goto out; |
| case STAT_IO_NO_DEVICE: |
| ts->stat = TMF_RESP_FUNC_COMPLETE; |
| goto out; |
| case STAT_IO_NOT_VALID: |
| /* abort single io, controller don't find |
| * the io need to abort |
| */ |
| ts->stat = TMF_RESP_FUNC_FAILED; |
| goto out; |
| default: |
| break; |
| } |
| |
| if ((complete_hdr->dw0 & CMPLT_HDR_ERX_MSK) && |
| (!(complete_hdr->dw0 & CMPLT_HDR_RSPNS_XFRD_MSK))) { |
| |
| slot_err_v2_hw(hisi_hba, task, slot); |
| if (unlikely(slot->abort)) { |
| queue_work(hisi_hba->wq, &slot->abort_slot); |
| /* immediately return and do not complete */ |
| return ts->stat; |
| } |
| goto out; |
| } |
| |
| switch (task->task_proto) { |
| case SAS_PROTOCOL_SSP: |
| { |
| struct ssp_response_iu *iu = slot->status_buffer + |
| sizeof(struct hisi_sas_err_record); |
| |
| sas_ssp_task_response(dev, task, iu); |
| break; |
| } |
| case SAS_PROTOCOL_SMP: |
| { |
| struct scatterlist *sg_resp = &task->smp_task.smp_resp; |
| void *to; |
| |
| ts->stat = SAM_STAT_GOOD; |
| to = kmap_atomic(sg_page(sg_resp)); |
| |
| dma_unmap_sg(dev, &task->smp_task.smp_resp, 1, |
| DMA_FROM_DEVICE); |
| dma_unmap_sg(dev, &task->smp_task.smp_req, 1, |
| DMA_TO_DEVICE); |
| memcpy(to + sg_resp->offset, |
| slot->status_buffer + |
| sizeof(struct hisi_sas_err_record), |
| sg_dma_len(sg_resp)); |
| kunmap_atomic(to); |
| break; |
| } |
| case SAS_PROTOCOL_SATA: |
| case SAS_PROTOCOL_STP: |
| case SAS_PROTOCOL_SATA | SAS_PROTOCOL_STP: |
| { |
| ts->stat = SAM_STAT_GOOD; |
| sata_done_v2_hw(hisi_hba, task, slot); |
| break; |
| } |
| default: |
| ts->stat = SAM_STAT_CHECK_CONDITION; |
| break; |
| } |
| |
| if (!slot->port->port_attached) { |
| dev_err(dev, "slot complete: port %d has removed\n", |
| slot->port->sas_port.id); |
| ts->stat = SAS_PHY_DOWN; |
| } |
| |
| out: |
| if (sas_dev && sas_dev->running_req) |
| sas_dev->running_req--; |
| |
| hisi_sas_slot_task_free(hisi_hba, task, slot); |
| sts = ts->stat; |
| |
| if (task->task_done) |
| task->task_done(task); |
| |
| return sts; |
| } |
| |
| static u8 get_ata_protocol(u8 cmd, int direction) |
| { |
| switch (cmd) { |
| case ATA_CMD_FPDMA_WRITE: |
| case ATA_CMD_FPDMA_READ: |
| case ATA_CMD_FPDMA_RECV: |
| case ATA_CMD_FPDMA_SEND: |
| case ATA_CMD_NCQ_NON_DATA: |
| return SATA_PROTOCOL_FPDMA; |
| |
| case ATA_CMD_ID_ATA: |
| case ATA_CMD_PMP_READ: |
| case ATA_CMD_READ_LOG_EXT: |
| case ATA_CMD_PIO_READ: |
| case ATA_CMD_PIO_READ_EXT: |
| case ATA_CMD_PMP_WRITE: |
| case ATA_CMD_WRITE_LOG_EXT: |
| case ATA_CMD_PIO_WRITE: |
| case ATA_CMD_PIO_WRITE_EXT: |
| return SATA_PROTOCOL_PIO; |
| |
| case ATA_CMD_READ: |
| case ATA_CMD_READ_EXT: |
| case ATA_CMD_READ_LOG_DMA_EXT: |
| case ATA_CMD_WRITE: |
| case ATA_CMD_WRITE_EXT: |
| case ATA_CMD_WRITE_QUEUED: |
| case ATA_CMD_WRITE_LOG_DMA_EXT: |
| return SATA_PROTOCOL_DMA; |
| |
| case ATA_CMD_DOWNLOAD_MICRO: |
| case ATA_CMD_DEV_RESET: |
| case ATA_CMD_CHK_POWER: |
| case ATA_CMD_FLUSH: |
| case ATA_CMD_FLUSH_EXT: |
| case ATA_CMD_VERIFY: |
| case ATA_CMD_VERIFY_EXT: |
| case ATA_CMD_SET_FEATURES: |
| case ATA_CMD_STANDBY: |
| case ATA_CMD_STANDBYNOW1: |
| return SATA_PROTOCOL_NONDATA; |
| default: |
| if (direction == DMA_NONE) |
| return SATA_PROTOCOL_NONDATA; |
| return SATA_PROTOCOL_PIO; |
| } |
| } |
| |
| static int get_ncq_tag_v2_hw(struct sas_task *task, u32 *tag) |
| { |
| struct ata_queued_cmd *qc = task->uldd_task; |
| |
| if (qc) { |
| if (qc->tf.command == ATA_CMD_FPDMA_WRITE || |
| qc->tf.command == ATA_CMD_FPDMA_READ) { |
| *tag = qc->tag; |
| return 1; |
| } |
| } |
| return 0; |
| } |
| |
| static int prep_ata_v2_hw(struct hisi_hba *hisi_hba, |
| struct hisi_sas_slot *slot) |
| { |
| struct sas_task *task = slot->task; |
| struct domain_device *device = task->dev; |
| struct domain_device *parent_dev = device->parent; |
| struct hisi_sas_device *sas_dev = device->lldd_dev; |
| struct hisi_sas_cmd_hdr *hdr = slot->cmd_hdr; |
| struct hisi_sas_port *port = device->port->lldd_port; |
| u8 *buf_cmd; |
| int has_data = 0, rc = 0, hdr_tag = 0; |
| u32 dw1 = 0, dw2 = 0; |
| |
| /* create header */ |
| /* dw0 */ |
| hdr->dw0 = cpu_to_le32(port->id << CMD_HDR_PORT_OFF); |
| if (parent_dev && DEV_IS_EXPANDER(parent_dev->dev_type)) |
| hdr->dw0 |= cpu_to_le32(3 << CMD_HDR_CMD_OFF); |
| else |
| hdr->dw0 |= cpu_to_le32(4 << CMD_HDR_CMD_OFF); |
| |
| /* dw1 */ |
| switch (task->data_dir) { |
| case DMA_TO_DEVICE: |
| has_data = 1; |
| dw1 |= DIR_TO_DEVICE << CMD_HDR_DIR_OFF; |
| break; |
| case DMA_FROM_DEVICE: |
| has_data = 1; |
| dw1 |= DIR_TO_INI << CMD_HDR_DIR_OFF; |
| break; |
| default: |
| dw1 &= ~CMD_HDR_DIR_MSK; |
| } |
| |
| if (0 == task->ata_task.fis.command) |
| dw1 |= 1 << CMD_HDR_RESET_OFF; |
| |
| dw1 |= (get_ata_protocol(task->ata_task.fis.command, task->data_dir)) |
| << CMD_HDR_FRAME_TYPE_OFF; |
| dw1 |= sas_dev->device_id << CMD_HDR_DEV_ID_OFF; |
| hdr->dw1 = cpu_to_le32(dw1); |
| |
| /* dw2 */ |
| if (task->ata_task.use_ncq && get_ncq_tag_v2_hw(task, &hdr_tag)) { |
| task->ata_task.fis.sector_count |= (u8) (hdr_tag << 3); |
| dw2 |= hdr_tag << CMD_HDR_NCQ_TAG_OFF; |
| } |
| |
| dw2 |= (HISI_SAS_MAX_STP_RESP_SZ / 4) << CMD_HDR_CFL_OFF | |
| 2 << CMD_HDR_SG_MOD_OFF; |
| hdr->dw2 = cpu_to_le32(dw2); |
| |
| /* dw3 */ |
| hdr->transfer_tags = cpu_to_le32(slot->idx); |
| |
| if (has_data) { |
| rc = prep_prd_sge_v2_hw(hisi_hba, slot, hdr, task->scatter, |
| slot->n_elem); |
| if (rc) |
| return rc; |
| } |
| |
| |
| hdr->data_transfer_len = cpu_to_le32(task->total_xfer_len); |
| hdr->cmd_table_addr = cpu_to_le64(slot->command_table_dma); |
| hdr->sts_buffer_addr = cpu_to_le64(slot->status_buffer_dma); |
| |
| buf_cmd = slot->command_table; |
| |
| if (likely(!task->ata_task.device_control_reg_update)) |
| task->ata_task.fis.flags |= 0x80; /* C=1: update ATA cmd reg */ |
| /* fill in command FIS */ |
| memcpy(buf_cmd, &task->ata_task.fis, sizeof(struct host_to_dev_fis)); |
| |
| return 0; |
| } |
| |
| static int prep_abort_v2_hw(struct hisi_hba *hisi_hba, |
| struct hisi_sas_slot *slot, |
| int device_id, int abort_flag, int tag_to_abort) |
| { |
| struct sas_task *task = slot->task; |
| struct domain_device *dev = task->dev; |
| struct hisi_sas_cmd_hdr *hdr = slot->cmd_hdr; |
| struct hisi_sas_port *port = slot->port; |
| |
| /* dw0 */ |
| hdr->dw0 = cpu_to_le32((5 << CMD_HDR_CMD_OFF) | /*abort*/ |
| (port->id << CMD_HDR_PORT_OFF) | |
| ((dev_is_sata(dev) ? 1:0) << |
| CMD_HDR_ABORT_DEVICE_TYPE_OFF) | |
| (abort_flag << CMD_HDR_ABORT_FLAG_OFF)); |
| |
| /* dw1 */ |
| hdr->dw1 = cpu_to_le32(device_id << CMD_HDR_DEV_ID_OFF); |
| |
| /* dw7 */ |
| hdr->dw7 = cpu_to_le32(tag_to_abort << CMD_HDR_ABORT_IPTT_OFF); |
| hdr->transfer_tags = cpu_to_le32(slot->idx); |
| |
| return 0; |
| } |
| |
| static int phy_up_v2_hw(int phy_no, struct hisi_hba *hisi_hba) |
| { |
| int i, res = 0; |
| u32 context, port_id, link_rate, hard_phy_linkrate; |
| struct hisi_sas_phy *phy = &hisi_hba->phy[phy_no]; |
| struct asd_sas_phy *sas_phy = &phy->sas_phy; |
| struct device *dev = &hisi_hba->pdev->dev; |
| u32 *frame_rcvd = (u32 *)sas_phy->frame_rcvd; |
| struct sas_identify_frame *id = (struct sas_identify_frame *)frame_rcvd; |
| |
| hisi_sas_phy_write32(hisi_hba, phy_no, PHYCTRL_PHY_ENA_MSK, 1); |
| |
| /* Check for SATA dev */ |
| context = hisi_sas_read32(hisi_hba, PHY_CONTEXT); |
| if (context & (1 << phy_no)) |
| goto end; |
| |
| if (phy_no == 8) { |
| u32 port_state = hisi_sas_read32(hisi_hba, PORT_STATE); |
| |
| port_id = (port_state & PORT_STATE_PHY8_PORT_NUM_MSK) >> |
| PORT_STATE_PHY8_PORT_NUM_OFF; |
| link_rate = (port_state & PORT_STATE_PHY8_CONN_RATE_MSK) >> |
| PORT_STATE_PHY8_CONN_RATE_OFF; |
| } else { |
| port_id = hisi_sas_read32(hisi_hba, PHY_PORT_NUM_MA); |
| port_id = (port_id >> (4 * phy_no)) & 0xf; |
| link_rate = hisi_sas_read32(hisi_hba, PHY_CONN_RATE); |
| link_rate = (link_rate >> (phy_no * 4)) & 0xf; |
| } |
| |
| if (port_id == 0xf) { |
| dev_err(dev, "phyup: phy%d invalid portid\n", phy_no); |
| res = IRQ_NONE; |
| goto end; |
| } |
| |
| for (i = 0; i < 6; i++) { |
| u32 idaf = hisi_sas_phy_read32(hisi_hba, phy_no, |
| RX_IDAF_DWORD0 + (i * 4)); |
| frame_rcvd[i] = __swab32(idaf); |
| } |
| |
| sas_phy->linkrate = link_rate; |
| hard_phy_linkrate = hisi_sas_phy_read32(hisi_hba, phy_no, |
| HARD_PHY_LINKRATE); |
| phy->maximum_linkrate = hard_phy_linkrate & 0xf; |
| phy->minimum_linkrate = (hard_phy_linkrate >> 4) & 0xf; |
| |
| sas_phy->oob_mode = SAS_OOB_MODE; |
| memcpy(sas_phy->attached_sas_addr, &id->sas_addr, SAS_ADDR_SIZE); |
| dev_info(dev, "phyup: phy%d link_rate=%d\n", phy_no, link_rate); |
| phy->port_id = port_id; |
| phy->phy_type &= ~(PORT_TYPE_SAS | PORT_TYPE_SATA); |
| phy->phy_type |= PORT_TYPE_SAS; |
| phy->phy_attached = 1; |
| phy->identify.device_type = id->dev_type; |
| phy->frame_rcvd_size = sizeof(struct sas_identify_frame); |
| if (phy->identify.device_type == SAS_END_DEVICE) |
| phy->identify.target_port_protocols = |
| SAS_PROTOCOL_SSP; |
| else if (phy->identify.device_type != SAS_PHY_UNUSED) |
| phy->identify.target_port_protocols = |
| SAS_PROTOCOL_SMP; |
| queue_work(hisi_hba->wq, &phy->phyup_ws); |
| |
| end: |
| hisi_sas_phy_write32(hisi_hba, phy_no, CHL_INT0, |
| CHL_INT0_SL_PHY_ENABLE_MSK); |
| hisi_sas_phy_write32(hisi_hba, phy_no, PHYCTRL_PHY_ENA_MSK, 0); |
| |
| return res; |
| } |
| |
| static int phy_down_v2_hw(int phy_no, struct hisi_hba *hisi_hba) |
| { |
| int res = 0; |
| u32 phy_state, sl_ctrl, txid_auto; |
| |
| hisi_sas_phy_write32(hisi_hba, phy_no, PHYCTRL_NOT_RDY_MSK, 1); |
| |
| phy_state = hisi_sas_read32(hisi_hba, PHY_STATE); |
| hisi_sas_phy_down(hisi_hba, phy_no, (phy_state & 1 << phy_no) ? 1 : 0); |
| |
| sl_ctrl = hisi_sas_phy_read32(hisi_hba, phy_no, SL_CONTROL); |
| hisi_sas_phy_write32(hisi_hba, phy_no, SL_CONTROL, |
| sl_ctrl & ~SL_CONTROL_CTA_MSK); |
| |
| txid_auto = hisi_sas_phy_read32(hisi_hba, phy_no, TXID_AUTO); |
| hisi_sas_phy_write32(hisi_hba, phy_no, TXID_AUTO, |
| txid_auto | TXID_AUTO_CT3_MSK); |
| |
| hisi_sas_phy_write32(hisi_hba, phy_no, CHL_INT0, CHL_INT0_NOT_RDY_MSK); |
| hisi_sas_phy_write32(hisi_hba, phy_no, PHYCTRL_NOT_RDY_MSK, 0); |
| |
| return res; |
| } |
| |
| static irqreturn_t int_phy_updown_v2_hw(int irq_no, void *p) |
| { |
| struct hisi_hba *hisi_hba = p; |
| u32 irq_msk; |
| int phy_no = 0; |
| irqreturn_t res = IRQ_HANDLED; |
| |
| irq_msk = (hisi_sas_read32(hisi_hba, HGC_INVLD_DQE_INFO) |
| >> HGC_INVLD_DQE_INFO_FB_CH0_OFF) & 0x1ff; |
| while (irq_msk) { |
| if (irq_msk & 1) { |
| u32 irq_value = hisi_sas_phy_read32(hisi_hba, phy_no, |
| CHL_INT0); |
| |
| if (irq_value & CHL_INT0_SL_PHY_ENABLE_MSK) |
| /* phy up */ |
| if (phy_up_v2_hw(phy_no, hisi_hba)) { |
| res = IRQ_NONE; |
| goto end; |
| } |
| |
| if (irq_value & CHL_INT0_NOT_RDY_MSK) |
| /* phy down */ |
| if (phy_down_v2_hw(phy_no, hisi_hba)) { |
| res = IRQ_NONE; |
| goto end; |
| } |
| } |
| irq_msk >>= 1; |
| phy_no++; |
| } |
| |
| end: |
| return res; |
| } |
| |
| static void phy_bcast_v2_hw(int phy_no, struct hisi_hba *hisi_hba) |
| { |
| struct hisi_sas_phy *phy = &hisi_hba->phy[phy_no]; |
| struct asd_sas_phy *sas_phy = &phy->sas_phy; |
| struct sas_ha_struct *sas_ha = &hisi_hba->sha; |
| |
| hisi_sas_phy_write32(hisi_hba, phy_no, SL_RX_BCAST_CHK_MSK, 1); |
| sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD); |
| hisi_sas_phy_write32(hisi_hba, phy_no, CHL_INT0, |
| CHL_INT0_SL_RX_BCST_ACK_MSK); |
| hisi_sas_phy_write32(hisi_hba, phy_no, SL_RX_BCAST_CHK_MSK, 0); |
| } |
| |
| static irqreturn_t int_chnl_int_v2_hw(int irq_no, void *p) |
| { |
| struct hisi_hba *hisi_hba = p; |
| struct device *dev = &hisi_hba->pdev->dev; |
| u32 ent_msk, ent_tmp, irq_msk; |
| int phy_no = 0; |
| |
| ent_msk = hisi_sas_read32(hisi_hba, ENT_INT_SRC_MSK3); |
| ent_tmp = ent_msk; |
| ent_msk |= ENT_INT_SRC_MSK3_ENT95_MSK_MSK; |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC_MSK3, ent_msk); |
| |
| irq_msk = (hisi_sas_read32(hisi_hba, HGC_INVLD_DQE_INFO) >> |
| HGC_INVLD_DQE_INFO_FB_CH3_OFF) & 0x1ff; |
| |
| while (irq_msk) { |
| if (irq_msk & (1 << phy_no)) { |
| u32 irq_value0 = hisi_sas_phy_read32(hisi_hba, phy_no, |
| CHL_INT0); |
| u32 irq_value1 = hisi_sas_phy_read32(hisi_hba, phy_no, |
| CHL_INT1); |
| u32 irq_value2 = hisi_sas_phy_read32(hisi_hba, phy_no, |
| CHL_INT2); |
| |
| if (irq_value1) { |
| if (irq_value1 & (CHL_INT1_DMAC_RX_ECC_ERR_MSK | |
| CHL_INT1_DMAC_TX_ECC_ERR_MSK)) |
| panic("%s: DMAC RX/TX ecc bad error! (0x%x)", |
| dev_name(dev), irq_value1); |
| |
| hisi_sas_phy_write32(hisi_hba, phy_no, |
| CHL_INT1, irq_value1); |
| } |
| |
| if (irq_value2) |
| hisi_sas_phy_write32(hisi_hba, phy_no, |
| CHL_INT2, irq_value2); |
| |
| |
| if (irq_value0) { |
| if (irq_value0 & CHL_INT0_SL_RX_BCST_ACK_MSK) |
| phy_bcast_v2_hw(phy_no, hisi_hba); |
| |
| hisi_sas_phy_write32(hisi_hba, phy_no, |
| CHL_INT0, irq_value0 |
| & (~CHL_INT0_HOTPLUG_TOUT_MSK) |
| & (~CHL_INT0_SL_PHY_ENABLE_MSK) |
| & (~CHL_INT0_NOT_RDY_MSK)); |
| } |
| } |
| irq_msk &= ~(1 << phy_no); |
| phy_no++; |
| } |
| |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC_MSK3, ent_tmp); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t cq_interrupt_v2_hw(int irq_no, void *p) |
| { |
| struct hisi_sas_cq *cq = p; |
| struct hisi_hba *hisi_hba = cq->hisi_hba; |
| struct hisi_sas_slot *slot; |
| struct hisi_sas_itct *itct; |
| struct hisi_sas_complete_v2_hdr *complete_queue; |
| u32 irq_value, rd_point = cq->rd_point, wr_point, dev_id; |
| int queue = cq->id; |
| |
| complete_queue = hisi_hba->complete_hdr[queue]; |
| irq_value = hisi_sas_read32(hisi_hba, OQ_INT_SRC); |
| |
| hisi_sas_write32(hisi_hba, OQ_INT_SRC, 1 << queue); |
| |
| wr_point = hisi_sas_read32(hisi_hba, COMPL_Q_0_WR_PTR + |
| (0x14 * queue)); |
| |
| while (rd_point != wr_point) { |
| struct hisi_sas_complete_v2_hdr *complete_hdr; |
| int iptt; |
| |
| complete_hdr = &complete_queue[rd_point]; |
| |
| /* Check for NCQ completion */ |
| if (complete_hdr->act) { |
| u32 act_tmp = complete_hdr->act; |
| int ncq_tag_count = ffs(act_tmp); |
| |
| dev_id = (complete_hdr->dw1 & CMPLT_HDR_DEV_ID_MSK) >> |
| CMPLT_HDR_DEV_ID_OFF; |
| itct = &hisi_hba->itct[dev_id]; |
| |
| /* The NCQ tags are held in the itct header */ |
| while (ncq_tag_count) { |
| __le64 *ncq_tag = &itct->qw4_15[0]; |
| |
| ncq_tag_count -= 1; |
| iptt = (ncq_tag[ncq_tag_count / 5] |
| >> (ncq_tag_count % 5) * 12) & 0xfff; |
| |
| slot = &hisi_hba->slot_info[iptt]; |
| slot->cmplt_queue_slot = rd_point; |
| slot->cmplt_queue = queue; |
| slot_complete_v2_hw(hisi_hba, slot, 0); |
| |
| act_tmp &= ~(1 << ncq_tag_count); |
| ncq_tag_count = ffs(act_tmp); |
| } |
| } else { |
| iptt = (complete_hdr->dw1) & CMPLT_HDR_IPTT_MSK; |
| slot = &hisi_hba->slot_info[iptt]; |
| slot->cmplt_queue_slot = rd_point; |
| slot->cmplt_queue = queue; |
| slot_complete_v2_hw(hisi_hba, slot, 0); |
| } |
| |
| if (++rd_point >= HISI_SAS_QUEUE_SLOTS) |
| rd_point = 0; |
| } |
| |
| /* update rd_point */ |
| cq->rd_point = rd_point; |
| hisi_sas_write32(hisi_hba, COMPL_Q_0_RD_PTR + (0x14 * queue), rd_point); |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t sata_int_v2_hw(int irq_no, void *p) |
| { |
| struct hisi_sas_phy *phy = p; |
| struct hisi_hba *hisi_hba = phy->hisi_hba; |
| struct asd_sas_phy *sas_phy = &phy->sas_phy; |
| struct device *dev = &hisi_hba->pdev->dev; |
| struct hisi_sas_initial_fis *initial_fis; |
| struct dev_to_host_fis *fis; |
| u32 ent_tmp, ent_msk, ent_int, port_id, link_rate, hard_phy_linkrate; |
| irqreturn_t res = IRQ_HANDLED; |
| u8 attached_sas_addr[SAS_ADDR_SIZE] = {0}; |
| int phy_no, offset; |
| |
| phy_no = sas_phy->id; |
| initial_fis = &hisi_hba->initial_fis[phy_no]; |
| fis = &initial_fis->fis; |
| |
| offset = 4 * (phy_no / 4); |
| ent_msk = hisi_sas_read32(hisi_hba, ENT_INT_SRC_MSK1 + offset); |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC_MSK1 + offset, |
| ent_msk | 1 << ((phy_no % 4) * 8)); |
| |
| ent_int = hisi_sas_read32(hisi_hba, ENT_INT_SRC1 + offset); |
| ent_tmp = ent_int & (1 << (ENT_INT_SRC1_D2H_FIS_CH1_OFF * |
| (phy_no % 4))); |
| ent_int >>= ENT_INT_SRC1_D2H_FIS_CH1_OFF * (phy_no % 4); |
| if ((ent_int & ENT_INT_SRC1_D2H_FIS_CH0_MSK) == 0) { |
| dev_warn(dev, "sata int: phy%d did not receive FIS\n", phy_no); |
| res = IRQ_NONE; |
| goto end; |
| } |
| |
| if (unlikely(phy_no == 8)) { |
| u32 port_state = hisi_sas_read32(hisi_hba, PORT_STATE); |
| |
| port_id = (port_state & PORT_STATE_PHY8_PORT_NUM_MSK) >> |
| PORT_STATE_PHY8_PORT_NUM_OFF; |
| link_rate = (port_state & PORT_STATE_PHY8_CONN_RATE_MSK) >> |
| PORT_STATE_PHY8_CONN_RATE_OFF; |
| } else { |
| port_id = hisi_sas_read32(hisi_hba, PHY_PORT_NUM_MA); |
| port_id = (port_id >> (4 * phy_no)) & 0xf; |
| link_rate = hisi_sas_read32(hisi_hba, PHY_CONN_RATE); |
| link_rate = (link_rate >> (phy_no * 4)) & 0xf; |
| } |
| |
| if (port_id == 0xf) { |
| dev_err(dev, "sata int: phy%d invalid portid\n", phy_no); |
| res = IRQ_NONE; |
| goto end; |
| } |
| |
| sas_phy->linkrate = link_rate; |
| hard_phy_linkrate = hisi_sas_phy_read32(hisi_hba, phy_no, |
| HARD_PHY_LINKRATE); |
| phy->maximum_linkrate = hard_phy_linkrate & 0xf; |
| phy->minimum_linkrate = (hard_phy_linkrate >> 4) & 0xf; |
| |
| sas_phy->oob_mode = SATA_OOB_MODE; |
| /* Make up some unique SAS address */ |
| attached_sas_addr[0] = 0x50; |
| attached_sas_addr[7] = phy_no; |
| memcpy(sas_phy->attached_sas_addr, attached_sas_addr, SAS_ADDR_SIZE); |
| memcpy(sas_phy->frame_rcvd, fis, sizeof(struct dev_to_host_fis)); |
| dev_info(dev, "sata int phyup: phy%d link_rate=%d\n", phy_no, link_rate); |
| phy->phy_type &= ~(PORT_TYPE_SAS | PORT_TYPE_SATA); |
| phy->port_id = port_id; |
| phy->phy_type |= PORT_TYPE_SATA; |
| phy->phy_attached = 1; |
| phy->identify.device_type = SAS_SATA_DEV; |
| phy->frame_rcvd_size = sizeof(struct dev_to_host_fis); |
| phy->identify.target_port_protocols = SAS_PROTOCOL_SATA; |
| queue_work(hisi_hba->wq, &phy->phyup_ws); |
| |
| end: |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC1 + offset, ent_tmp); |
| hisi_sas_write32(hisi_hba, ENT_INT_SRC_MSK1 + offset, ent_msk); |
| |
| return res; |
| } |
| |
| static irq_handler_t phy_interrupts[HISI_SAS_PHY_INT_NR] = { |
| int_phy_updown_v2_hw, |
| int_chnl_int_v2_hw, |
| }; |
| |
| /** |
| * There is a limitation in the hip06 chipset that we need |
| * to map in all mbigen interrupts, even if they are not used. |
| */ |
| static int interrupt_init_v2_hw(struct hisi_hba *hisi_hba) |
| { |
| struct platform_device *pdev = hisi_hba->pdev; |
| struct device *dev = &pdev->dev; |
| int i, irq, rc, irq_map[128]; |
| |
| |
| for (i = 0; i < 128; i++) |
| irq_map[i] = platform_get_irq(pdev, i); |
| |
| for (i = 0; i < HISI_SAS_PHY_INT_NR; i++) { |
| int idx = i; |
| |
| irq = irq_map[idx + 1]; /* Phy up/down is irq1 */ |
| if (!irq) { |
| dev_err(dev, "irq init: fail map phy interrupt %d\n", |
| idx); |
| return -ENOENT; |
| } |
| |
| rc = devm_request_irq(dev, irq, phy_interrupts[i], 0, |
| DRV_NAME " phy", hisi_hba); |
| if (rc) { |
| dev_err(dev, "irq init: could not request " |
| "phy interrupt %d, rc=%d\n", |
| irq, rc); |
| return -ENOENT; |
| } |
| } |
| |
| for (i = 0; i < hisi_hba->n_phy; i++) { |
| struct hisi_sas_phy *phy = &hisi_hba->phy[i]; |
| int idx = i + 72; /* First SATA interrupt is irq72 */ |
| |
| irq = irq_map[idx]; |
| if (!irq) { |
| dev_err(dev, "irq init: fail map phy interrupt %d\n", |
| idx); |
| return -ENOENT; |
| } |
| |
| rc = devm_request_irq(dev, irq, sata_int_v2_hw, 0, |
| DRV_NAME " sata", phy); |
| if (rc) { |
| dev_err(dev, "irq init: could not request " |
| "sata interrupt %d, rc=%d\n", |
| irq, rc); |
| return -ENOENT; |
| } |
| } |
| |
| for (i = 0; i < hisi_hba->queue_count; i++) { |
| int idx = i + 96; /* First cq interrupt is irq96 */ |
| |
| irq = irq_map[idx]; |
| if (!irq) { |
| dev_err(dev, |
| "irq init: could not map cq interrupt %d\n", |
| idx); |
| return -ENOENT; |
| } |
| rc = devm_request_irq(dev, irq, cq_interrupt_v2_hw, 0, |
| DRV_NAME " cq", &hisi_hba->cq[i]); |
| if (rc) { |
| dev_err(dev, |
| "irq init: could not request cq interrupt %d, rc=%d\n", |
| irq, rc); |
| return -ENOENT; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int hisi_sas_v2_init(struct hisi_hba *hisi_hba) |
| { |
| int rc; |
| |
| rc = hw_init_v2_hw(hisi_hba); |
| if (rc) |
| return rc; |
| |
| rc = interrupt_init_v2_hw(hisi_hba); |
| if (rc) |
| return rc; |
| |
| phys_init_v2_hw(hisi_hba); |
| |
| return 0; |
| } |
| |
| static const struct hisi_sas_hw hisi_sas_v2_hw = { |
| .hw_init = hisi_sas_v2_init, |
| .setup_itct = setup_itct_v2_hw, |
| .slot_index_alloc = slot_index_alloc_quirk_v2_hw, |
| .alloc_dev = alloc_dev_quirk_v2_hw, |
| .sl_notify = sl_notify_v2_hw, |
| .get_wideport_bitmap = get_wideport_bitmap_v2_hw, |
| .free_device = free_device_v2_hw, |
| .prep_smp = prep_smp_v2_hw, |
| .prep_ssp = prep_ssp_v2_hw, |
| .prep_stp = prep_ata_v2_hw, |
| .prep_abort = prep_abort_v2_hw, |
| .get_free_slot = get_free_slot_v2_hw, |
| .start_delivery = start_delivery_v2_hw, |
| .slot_complete = slot_complete_v2_hw, |
| .phy_enable = enable_phy_v2_hw, |
| .phy_disable = disable_phy_v2_hw, |
| .phy_hard_reset = phy_hard_reset_v2_hw, |
| .max_command_entries = HISI_SAS_COMMAND_ENTRIES_V2_HW, |
| .complete_hdr_size = sizeof(struct hisi_sas_complete_v2_hdr), |
| }; |
| |
| static int hisi_sas_v2_probe(struct platform_device *pdev) |
| { |
| return hisi_sas_probe(pdev, &hisi_sas_v2_hw); |
| } |
| |
| static int hisi_sas_v2_remove(struct platform_device *pdev) |
| { |
| return hisi_sas_remove(pdev); |
| } |
| |
| static const struct of_device_id sas_v2_of_match[] = { |
| { .compatible = "hisilicon,hip06-sas-v2",}, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, sas_v2_of_match); |
| |
| static const struct acpi_device_id sas_v2_acpi_match[] = { |
| { "HISI0162", 0 }, |
| { } |
| }; |
| |
| MODULE_DEVICE_TABLE(acpi, sas_v2_acpi_match); |
| |
| static struct platform_driver hisi_sas_v2_driver = { |
| .probe = hisi_sas_v2_probe, |
| .remove = hisi_sas_v2_remove, |
| .driver = { |
| .name = DRV_NAME, |
| .of_match_table = sas_v2_of_match, |
| .acpi_match_table = ACPI_PTR(sas_v2_acpi_match), |
| }, |
| }; |
| |
| module_platform_driver(hisi_sas_v2_driver); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_AUTHOR("John Garry <john.garry@huawei.com>"); |
| MODULE_DESCRIPTION("HISILICON SAS controller v2 hw driver"); |
| MODULE_ALIAS("platform:" DRV_NAME); |