| # This file allows user to override the factory |
| |
| # defaults for the WLAN Driver |
| |
| |
| # Enable IMPS or not |
| gEnableImps=1 |
| |
| # Enable/Disable Idle Scan |
| |
| gEnableIdleScan=0 |
| |
| |
| # Increase sleep duration (seconds) during IMPS |
| # 0 implies no periodic wake up from IMPS. Periodic wakeup is |
| # unnecessary if Idle Scan is disabled. |
| gImpsModSleepTime=0 |
| |
| |
| # Enable BMPS or not |
| gEnableBmps=1 |
| |
| # Enable suspend or not |
| |
| # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter |
| |
| gEnableSuspend=3 |
| |
| |
| # Phy Mode (auto, b, g, n, etc) |
| # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac |
| # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only |
| # 7 = 11b only 8 = 11ac only. |
| gDot11Mode=0 |
| |
| |
| # CSR Roaming Enable(1) Disable(0) |
| |
| gRoamingTime=0 |
| |
| |
| # Assigned MAC Addresses - This will be used until NV items are in place |
| |
| # Each byte of MAC address is represented in Hex format as XX |
| |
| Intf0MacAddress=000AF58989FF |
| Intf1MacAddress=000AF58989FE |
| Intf2MacAddress=000AF58989FD |
| |
| Intf3MacAddress=000AF58989FC |
| |
| |
| # UAPSD service interval for VO,VI, BE, BK traffic |
| |
| InfraUapsdVoSrvIntv=0 |
| |
| InfraUapsdViSrvIntv=0 |
| |
| InfraUapsdBeSrvIntv=0 |
| |
| InfraUapsdBkSrvIntv=0 |
| |
| # Flag to allow STA send AddTspec even when ACM is Off |
| gAddTSWhenACMIsOff=1 |
| |
| # Make 1x1 the default antenna configuration |
| |
| gNumRxAnt=1 |
| |
| |
| # Beacon filtering frequency (unit in beacon intervals) |
| |
| gNthBeaconFilter=50 |
| |
| |
| # Enable WAPI or not |
| |
| # WAPIIsEnabled=0 |
| |
| |
| # Flags to filter Mcast abd Bcast RX packets. |
| |
| # Value 0: No filtering, 1: Filter all Multicast. |
| |
| # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast |
| |
| McastBcastFilter=3 |
| |
| |
| #Flag to enable HostARPOffload feature or not |
| |
| hostArpOffload=1 |
| |
| #Flag to enable TCPChkSumOffld feature or not |
| |
| gEnableTCPChkSumOffld=1 |
| |
| #Flag to enable HostNSOffload feature or not |
| |
| hostNSOffload=1 |
| |
| #Flag to enable IPChkSumOffld feature or not |
| |
| gEnableIPChecksumOffload=0 |
| |
| #SoftAP Related Parameters |
| |
| # AP MAc addr |
| |
| gAPMacAddr=000AF589dcab |
| |
| |
| # 802.11n Protection flag |
| |
| gEnableApProt=1 |
| |
| |
| #Enable OBSS protection |
| |
| gEnableApOBSSProt=1 |
| |
| |
| #Enable/Disable UAPSD for SoftAP |
| |
| gEnableApUapsd=1 |
| |
| |
| # Fixed Rate |
| |
| gFixedRate=0 |
| |
| |
| # Maximum Tx power |
| |
| # gTxPowerCap=30 |
| |
| |
| # Fragmentation Threshold |
| |
| # gFragmentationThreshold=2346 |
| |
| |
| # RTS threshold |
| |
| RTSThreshold=192000 |
| |
| |
| # Intra-BSS forward |
| |
| gDisableIntraBssFwd=0 |
| |
| |
| # WMM Enable/Disable |
| |
| WmmIsEnabled=0 |
| |
| |
| # 802.11d support |
| |
| g11dSupportEnabled=1 |
| |
| # 802.11h support |
| |
| g11hSupportEnabled=1 |
| |
| # ESE Support and fast transition |
| EseEnabled=0 |
| ImplicitQosIsEnabled=0 |
| gNeighborScanTimerPeriod=200 |
| |
| gNeighborLookupThreshold=76 |
| gNeighborReassocThreshold=81 |
| |
| gNeighborScanChannelMinTime=20 |
| gNeighborScanChannelMaxTime=30 |
| gMaxNeighborReqTries=3 |
| |
| # Legacy (non-ESE, non-802.11r) Fast Roaming Support |
| # To enable, set FastRoamEnabled=1 |
| # To disable, set FastRoamEnabled=0 |
| FastRoamEnabled=1 |
| |
| #Check if the AP to which we are roaming is better than current AP in terms of RSSI. |
| #Checking is disabled if set to Zero.Otherwise it will use this value as to how better |
| #the RSSI of the new/roamable AP should be for roaming |
| RoamRssiDiff=3 |
| |
| # If the RSSI of any available candidate is better than currently associated |
| # AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without |
| # registering for reassoc threshold). |
| # NOTE: Value of 0 means that we would register for reassoc threshold. |
| gImmediateRoamRssiDiff=10 |
| |
| # To enable, set gRoamIntraBand=1 (Roaming within band) |
| # To disable, set gRoamIntraBand=0 (Roaming across band) |
| gRoamIntraBand=0 |
| |
| # SAP Country code |
| |
| # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. |
| |
| # Example |
| |
| # US Indoor, USI |
| |
| # Korea Outdoor, KRO |
| |
| # Japan without optional byte, JP |
| |
| # France without optional byte, FR |
| |
| #gAPCntryCode=USI |
| |
| |
| #Short Guard Interval Enable/disable |
| |
| gShortGI20Mhz=1 |
| |
| gShortGI40Mhz=1 |
| |
| |
| #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled |
| |
| gAPAutoShutOff=0 |
| |
| |
| # SAP auto channel selection configuration |
| |
| # 0 = disable auto channel selection |
| |
| # 1 = enable auto channel selection, channel provided by supplicant will be ignored |
| |
| gApAutoChannelSelection=0 |
| |
| |
| # Listen Energy Detect Mode Configuration |
| |
| # Valid values 0-128 |
| |
| # 128 means disable Energy Detect feature |
| |
| # 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. |
| |
| # 10-128 are reserved. |
| |
| # The EDET threshold mapping is as follows in 3dB step: |
| |
| # 0 = -60 dBm |
| |
| # 1 = -63 dBm |
| |
| # 2 = -66 dBm |
| |
| # ... |
| |
| # 7 = -81 dBm |
| |
| # 8 = -84 dBm |
| |
| # 9 = -87 dBm |
| |
| # Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: |
| |
| # |
| |
| # Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. |
| |
| # |
| |
| gEnablePhyAgcListenMode=128 |
| |
| |
| #Preferred band (both or 2.4 only or 5 only) |
| |
| BandCapability=0 |
| |
| |
| #Beacon Early Termination (1 = enable the BET feature, 0 = disable) |
| |
| enableBeaconEarlyTermination=0 |
| |
| beaconEarlyTerminationWakeInterval=3 |
| |
| |
| #SOFTAP Channel Range selection |
| |
| gAPChannelSelectStartChannel=1 |
| |
| gAPChannelSelectEndChannel=11 |
| |
| |
| #SOFTAP Channel Range selection Operating band |
| |
| # 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND |
| |
| gAPChannelSelectOperatingBand=0 |
| |
| |
| #Channel Bonding |
| gChannelBondingMode5GHz=1 |
| |
| |
| #Enable Keep alive with non-zero period value |
| |
| gStaKeepAlivePeriod = 30 |
| |
| #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). |
| #For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) |
| #For both active and power save clients. |
| |
| #Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. |
| #If doesn't honor for 5 seconds then DUT remove client. |
| |
| #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on |
| #11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. |
| #Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. |
| |
| #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period |
| #where we send NULL frame. |
| |
| #gApLinkMonitorPeriod = 10 |
| |
| #gGoLinkMonitorPeriod = 10 |
| |
| #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. |
| #Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. |
| |
| |
| gGoKeepAlivePeriod = 20 |
| |
| gApKeepAlivePeriod = 20 |
| |
| |
| #If set will start with active scan after driver load, otherwise will start with |
| |
| #passive scan to find out the domain |
| |
| gEnableBypass11d=1 |
| |
| |
| #If set to 0, will not scan DFS channels |
| |
| gEnableDFSChnlScan=1 |
| |
| |
| gVhtChannelWidth=2 |
| gEnableLogp=1 |
| |
| |
| # Enable Automatic Tx Power control |
| |
| gEnableAutomaticTxPowerControl=1 |
| |
| # 0 for OLPC 1 for CLPC and SCPC |
| gEnableCloseLoop=1 |
| |
| #Data Inactivity Timeout when in powersave (in ms) |
| gDataInactivityTimeout=200 |
| |
| # VHT Tx/Rx MCS values |
| # Valid values are 0,1,2. If commented out, the default value is 0. |
| # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| gVhtRxMCS=2 |
| gVhtTxMCS=2 |
| |
| # VHT Tx/Rx MCS values for 2x2 |
| # Valid values are 0,1,2. If commented out, the default value is 0. |
| # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| gEnable2x2=1 |
| gVhtRxMCS2x2=0 |
| gVhtTxMCS2x2=2 |
| |
| # Scan Timing Parameters |
| # gPassiveMaxChannelTime=110 |
| # gPassiveMinChannelTime=60 |
| # gActiveMaxChannelTime=40 |
| # gActiveMinChannelTime=20 |
| |
| #If set to 0, MCC is not allowed. |
| gEnableMCCMode=1 |
| |
| # 1=enable STBC; 0=disable STBC |
| gEnableRXSTBC=1 |
| |
| # 1=enable tx STBC; 0=disable |
| gEnableTXSTBC=1 |
| |
| # 1=enable rx LDPC; 0=disable |
| gEnableRXLDPC=1 |
| |
| # Enable Active mode offload |
| gEnableActiveModeOffload=1 |
| |
| #Enable Scan Results Aging based on timer |
| #Timer value is in seconds |
| #If Set to 0 it will not enable the feature |
| gScanAgingTime=0 |
| |
| #Enable Power saving mechanism Based on Android Framework |
| #If set to 0 Driver internally control the Power saving mechanism |
| #If set to 1 Android Framwrok control the Power saving mechanism |
| isAndroidPsEn=0 |
| |
| #disable LDPC in STA mode if the AP is TXBF capable |
| gDisableLDPCWithTxbfAP=1 |
| |
| #Enable thermal mitigation |
| gThermalMitigationEnable=1 |
| gThermalTempMinLevel1=90 |
| gThermalTempMaxLevel0=110 |
| gThermalTempMaxLevel1=115 |
| gThrottlePeriod=100 |
| |
| gEnableFastRoamInConcurrency=1 |
| |
| #List of Country codes for which 11ac needs to be disabled |
| #Each country code must be delimited by comma(,) |
| gListOfNon11acCountryCode=RU,UA,ZA |
| |
| #Maxium Channel time in msec |
| gMaxMediumTime = 6000 |
| |
| # 802.11K support |
| gRrmEnable=1 |
| gRrmOperChanMax=8 |
| gRrmNonOperChanMax=8 |
| gRrmRandIntvl=100 |
| |
| #Scan offload |
| gEnableDirectedScanOffload=1 |
| |
| #FlexConnect Power Factor |
| #Default is set to 0 (disable) |
| gFlexConnectPowerFactor=0 |
| |
| #Disable split scan, the FW will take care of it |
| gNumChanCombinedConc=60 |
| |
| #Enable Power Save offload |
| gEnablePowerSaveOffload=1 |
| |
| #Enable firmware uart print |
| gEnablefwprint=0 |
| |
| #Enable firmware log |
| gEnablefwlog=1 |
| |
| #IPA config |
| gIPAEnable=1 |
| gIPADescSize=800 |
| gIPAPreFilterEnable=1 |
| gIPARMEnable=1 |
| |
| #P2P Listen offload |
| gEnableP2pListenOffload=1 |
| |
| # Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k) |
| gVhtAmpduLenExponent=7 |
| |
| # Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets) |
| gVhtMpduLen=0 |
| |
| # Maximum number of wow filters required |
| #gMaxWoWFilters=22 |
| |
| # WOW Enable/Disable. |
| # 0 - Disable both magic pattern match and pattern byte match. |
| # 1 - Enable magic pattern match on all interfaces. |
| # 2 - Enable pattern byte match on all interfaces. |
| # 3 - Enable both magic patter and pattern byte match on all interfaces. |
| # Default value of gEnableWoW is 3. |
| # gEnableWoW=0 |
| |
| # Enable or Disable MCC Adaptive Scheduler at the FW |
| # 1=Enable (default), 0=Disable |
| gEnableMCCAdaptiveScheduler=1 |
| |
| #Enable or Disable p2p device address administered |
| isP2pDeviceAddrAdministrated=0 |
| |
| #Disable scan_pno by default |
| gPNOScanSupport=0 |
| |
| #Enable TDLS |
| gEnableTDLSSupport=1 |
| |
| # Regulatory Setting; 0=STRICT; 1=CUSTOM |
| gRegulatoryChangeCountry=1 |
| |
| # Disable FW log function by default |
| gFwDebugLogType=0 |
| gFwDebugModuleLoglevel=0,0 |
| |
| # Enable or Disable Rx thread |
| # 1=Enable (default), 0=Disable |
| gEnableRxThread=0 |
| |
| # Enable or Disable FW self-recovery |
| # Currently, It's for USB only. |
| # 1=Enable, 0=Disable (default) |
| gEnableFwSelfRecovery=0 |
| |
| # Enable or Disable SAP suspend |
| # 1=Enable (default), 0=Disable |
| gEnableSapSuspend=0 |
| |
| # Enable TxBF |
| gTxBFEnable=1 |
| |
| # Enable or Disable DHCP Server offload |
| # 1=Enable, 0=Disable (default) |
| gDHCPServerOffloadEnable=0 |
| # Set max number of DHCP Clients |
| # Its value could not be greater than 10 |
| #gDHCPMaxNumClients=10 |
| # Set DHCP server IP |
| # 4th field could not be greater than 99, that is xxx,xxx,xxx,0 ~ xxx,xxx,xxx,99 |
| # 1st field could not be within the range of 224 ~ 239 (multicast IP address) |
| #gDHCPServerIP=192,168,1,2 |
| |
| # gEnableSAPAuthOffload: Enable Software AP Authentication Offload feature |
| # 1=Enable, 0=Disable (default) |
| gEnableSAPAuthOffload=0 |
| # gSAPAuthOffloadSec: Software AP Authentication Offload security Type, 0: disabled, 1: WPA2-PSK CCMP |
| # gSAPAuthOffloadSec=1 |
| # gSAPAuthOffloadKey: Passphrase of Security |
| # gSAPAuthOffloadKey=12345678 |
| |
| |
| # Enable or Disable UDP response offload feature |
| # 1=Enable, 0=Disable (default) |
| gudp_resp_offload_support=0 |
| # Set UDP packet dest port |
| # It's value is between 0 and 65535 |
| # Default is 0 |
| # gudp_resp_offload_dest_port=0 |
| # Set UDP payload filter |
| # It is only include Arabic numerals and English letter |
| # It's length should be between 1 and 127 |
| # gudp_resp_offload_payload_filter=require status |
| # Set UDP response payload |
| # It is only include Arabic numerals and English letter |
| # It's length should be between 1 and 127 |
| # gudp_resp_offload_response_payload=status=off |
| |
| |
| |
| |
| # Enable or Disable WOW Pulse feature |
| # 1 = Enable, 0 = Disable (default) |
| gwow_pulse_support = 0 |
| # GPIO PIN |
| # It's value is between 0 and 255 |
| # Default is 35 |
| # gwow_pulse_pin = 35 |
| # Set WOW Pulse interval low |
| # It's value is between 160 and 480 |
| # gwow_pulse_interval_low = 180 |
| # Set WOW Pulse interval high |
| # It's value is between 20 and 40 |
| # gwow_pulse_interval_high = 20 |
| |
| |
| END |
| |
| # Note: Configuration parser would not read anything past the END marker |
| |
