blob: d40192c8de62b3a7136288808f259fade3bed10d [file] [log] [blame]
/*
* Copyright (c) 2012-2015 The Linux Foundation. All rights reserved.
*
* Previously licensed under the ISC license by Qualcomm Atheros, Inc.
*
*
* Permission to use, copy, modify, and/or distribute this software for
* any purpose with or without fee is hereby granted, provided that the
* above copyright notice and this permission notice appear in all
* copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
* WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE
* AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL
* DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR
* PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER
* TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
* PERFORMANCE OF THIS SOFTWARE.
*/
/*
* This file was originally distributed by Qualcomm Atheros, Inc.
* under proprietary terms before Copyright ownership was assigned
* to the Linux Foundation.
*/
//------------------------------------------------------------------------------
// <copyright file="targaddrs.h" company="Atheros">
// Copyright (c) 2010 Atheros Corporation. All rights reserved.
// $ATH_LICENSE_HOSTSDK0_C$
//------------------------------------------------------------------------------
//==============================================================================
// Author(s): ="Atheros"
//==============================================================================
#ifndef __TARGADDRS_H__
#define __TARGADDRS_H__
#if defined(ATH_TARGET)
#include "soc_addrs.h"
#endif
#if !defined(ATH_TARGET)
#include "athstartpack.h"
#endif
/*
* SOC option bits, to enable/disable various features.
* By default, all option bits are 0.
* AR6004: These bits can be set in LOCAL_SCRATCH register 0.
* AR9888: These bits can be set in soc_core register SCRATCH_0.
*/
#define SOC_OPTION_BMI_DISABLE 0x01 /* Disable BMI comm with Host */
#define SOC_OPTION_SERIAL_ENABLE 0x02 /* Enable serial port msgs */
#define SOC_OPTION_WDT_DISABLE 0x04 /* WatchDog Timer override */
#define SOC_OPTION_SLEEP_DISABLE 0x08 /* Disable system sleep */
#define SOC_OPTION_STOP_BOOT 0x10 /* Stop boot processes (for ATE) */
#define SOC_OPTION_ENABLE_NOANI 0x20 /* Operate without ANI */
#define SOC_OPTION_DSET_DISABLE 0x40 /* Ignore DataSets */
#define SOC_OPTION_IGNORE_FLASH 0x80 /* Ignore flash during bootup */
/*
* xxx_HOST_INTEREST_ADDRESS is the address in Target RAM of the
* host_interest structure. It must match the address of the _host_interest
* symbol (see linker script).
*
* Host Interest is shared between Host and Target in order to coordinate
* between the two, and is intended to remain constant (with additions only
* at the end) across software releases.
*
* All addresses are available here so that it's possible to
* write a single binary that works with all Target Types.
* May be used in assembler code as well as C.
*/
#define AR6002_HOST_INTEREST_ADDRESS 0x00500400
#define AR6003_HOST_INTEREST_ADDRESS 0x00540600
#define AR6004_HOST_INTEREST_ADDRESS 0x00400800
#define AR9888_HOST_INTEREST_ADDRESS 0x00400800
#define AR900B_HOST_INTEREST_ADDRESS 0x00400800
#define AR6320_HOST_INTEREST_ADDRESS 0x00400800
#define AR6004_SOC_RESET_ADDRESS 0X00004000
#define AR6004_SOC_RESET_CPU_INIT_RESET_MASK 0X00000800
#if defined(AR6006_MEMORY_NEW_ARCH)
#define AR6006_HOST_INTEREST_ADDRESS 0x00428800
#else
#define AR6006_HOST_INTEREST_ADDRESS 0x00400800
#endif
#define AR6006_SOC_RESET_ADDRESS 0X00004000
#define AR6006_SOC_RESET_CPU_INIT_RESET_MASK 0X00000800
#define HOST_INTEREST_MAX_SIZE 0x200
#if !defined(__ASSEMBLER__)
struct register_dump_s;
struct dbglog_hdr_s;
/*
* These are items that the Host may need to access
* via BMI or via the Diagnostic Window. The position
* of items in this structure must remain constant
* across firmware revisions!
*
* Types for each item must be fixed size across
* target and host platforms.
*
* More items may be added at the end.
*/
PREPACK64 struct host_interest_s {
/*
* Pointer to application-defined area, if any.
* Set by Target application during startup.
*/
A_UINT32 hi_app_host_interest; /* 0x00 */
/* Pointer to register dump area, valid after Target crash. */
A_UINT32 hi_failure_state; /* 0x04 */
/* Pointer to debug logging header */
A_UINT32 hi_dbglog_hdr; /* 0x08 */
/* Save SW ROM version */
A_UINT32 hi_sw_rom_version; /* 0x0c */
/*
* General-purpose flag bits, similar to SOC_OPTION_* flags.
* Can be used by application rather than by OS.
*/
A_UINT32 hi_option_flag; /* 0x10 */
/*
* Boolean that determines whether or not to
* display messages on the serial port.
*/
A_UINT32 hi_serial_enable; /* 0x14 */
/* Start address of DataSet index, if any */
A_UINT32 hi_dset_list_head; /* 0x18 */
/* Override Target application start address */
A_UINT32 hi_app_start; /* 0x1c */
/* Clock and voltage tuning */
A_UINT32 hi_skip_clock_init; /* 0x20 */
A_UINT32 hi_core_clock_setting; /* 0x24 */
A_UINT32 hi_cpu_clock_setting; /* 0x28 */
A_UINT32 hi_system_sleep_setting; /* 0x2c */
A_UINT32 hi_xtal_control_setting; /* 0x30 */
A_UINT32 hi_pll_ctrl_setting_24ghz; /* 0x34 */
A_UINT32 hi_pll_ctrl_setting_5ghz; /* 0x38 */
A_UINT32 hi_ref_voltage_trim_setting; /* 0x3c */
A_UINT32 hi_clock_info; /* 0x40 */
/* Host uses BE CPU or not */
A_UINT32 hi_be; /* 0x44 */
A_UINT32 hi_stack; /* normal stack */ /* 0x48 */
A_UINT32 hi_err_stack; /* error stack */ /* 0x4c */
A_UINT32 hi_desired_cpu_speed_hz; /* 0x50 */
/* Pointer to Board Data */
A_UINT32 hi_board_data; /* 0x54 */
/*
* Indication of Board Data state:
* 0: board data is not yet initialized.
* 1: board data is initialized; unknown size
* >1: number of bytes of initialized board data (varies with board type)
*/
A_UINT32 hi_board_data_initialized; /* 0x58 */
A_UINT32 hi_dset_RAM_index_table; /* 0x5c */
A_UINT32 hi_desired_baud_rate; /* 0x60 */
A_UINT32 hi_dbglog_config; /* 0x64 */
A_UINT32 hi_end_RAM_reserve_sz; /* 0x68 */
A_UINT32 hi_mbox_io_block_sz; /* 0x6c */
A_UINT32 hi_num_bpatch_streams; /* 0x70 -- unused */
A_UINT32 hi_mbox_isr_yield_limit; /* 0x74 */
A_UINT32 hi_refclk_hz; /* 0x78 */
A_UINT32 hi_ext_clk_detected; /* 0x7c */
A_UINT32 hi_dbg_uart_txpin; /* 0x80 */
A_UINT32 hi_dbg_uart_rxpin; /* 0x84 */
A_UINT32 hi_hci_uart_baud; /* 0x88 */
A_UINT32 hi_hci_uart_pin_assignments; /* 0x8C */
/* NOTE: byte [0] = tx pin, [1] = rx pin, [2] = rts pin, [3] = cts pin */
A_UINT32 hi_hci_uart_baud_scale_val; /* 0x90 */
A_UINT32 hi_hci_uart_baud_step_val; /* 0x94 */
A_UINT32 hi_allocram_start; /* 0x98 */
A_UINT32 hi_allocram_sz; /* 0x9c */
A_UINT32 hi_hci_bridge_flags; /* 0xa0 */
A_UINT32 hi_hci_uart_support_pins; /* 0xa4 */
/* NOTE: byte [0] = RESET pin (bit 7 is polarity), bytes[1]..bytes[3] are for future use */
A_UINT32 hi_hci_uart_pwr_mgmt_params; /* 0xa8 */
/* 0xa8 - [1]: 0 = UART FC active low, 1 = UART FC active high
* [31:16]: wakeup timeout in ms
*/
/* Pointer to extended board Data */
A_UINT32 hi_board_ext_data; /* 0xac */
A_UINT32 hi_board_ext_data_config; /* 0xb0 */
/*
* Bit [0] : valid
* Bit[31:16: size
*/
/*
* hi_reset_flag is used to do some stuff when target reset.
* such as restore app_start after warm reset or
* preserve host Interest area, or preserve ROM data, literals etc.
*/
A_UINT32 hi_reset_flag; /* 0xb4 */
/* indicate hi_reset_flag is valid */
A_UINT32 hi_reset_flag_valid; /* 0xb8 */
A_UINT32 hi_hci_uart_pwr_mgmt_params_ext; /* 0xbc */
/* 0xbc - [31:0]: idle timeout in ms
*/
/* ACS flags */
A_UINT32 hi_acs_flags; /* 0xc0 */
A_UINT32 hi_console_flags; /* 0xc4 */
A_UINT32 hi_nvram_state; /* 0xc8 */
A_UINT32 hi_option_flag2; /* 0xcc */
/* If non-zero, override values sent to Host in WMI_READY event. */
A_UINT32 hi_sw_version_override; /* 0xd0 */
A_UINT32 hi_abi_version_override; /* 0xd4 */
/* Percentage of high priority RX traffic to total expected RX traffic -
* applicable only to ar6004 */
A_UINT32 hi_hp_rx_traffic_ratio; /* 0xd8 */
/* test applications flags */
A_UINT32 hi_test_apps_related ; /* 0xdc */
/* location of test script */
A_UINT32 hi_ota_testscript; /* 0xe0 */
/* location of CAL data */
A_UINT32 hi_cal_data; /* 0xe4 */
/* Number of packet log buffers */
A_UINT32 hi_pktlog_num_buffers; /* 0xe8 */
/* wow extension configuration */
A_UINT32 hi_wow_ext_config; /* 0xec */
A_UINT32 hi_pwr_save_flags; /* 0xf0 */
/* Spatial Multiplexing Power Save (SMPS) options */
A_UINT32 hi_smps_options; /* 0xf4 */
/* Interconnect-specific state */
A_UINT32 hi_interconnect_state; /* 0xf8 */
/* Coex configuration flags */
A_UINT32 hi_coex_config; /* 0xfc */
/* Early allocation support */
A_UINT32 hi_early_alloc; /* 0x100 */
/* FW swap field */
/* Bits of this 32bit word will be used to pass specific swap
instruction to FW */
/* Bit 0 -- AP Nart descriptor no swap. When this bit is set
FW will not swap TX descriptor. Meaning packets are formed
on the target processor.*/
/* Bit 1 -- TBD */
A_UINT32 hi_fw_swap; /* 0x104 */
/* global arenas pointer address, used by host driver debug */
A_UINT32 hi_dynamic_mem_arenas_addr; /* 0x108 */
/* allocated bytes of DRAM use by allocated */
A_UINT32 hi_dynamic_mem_allocated; /* 0x10C */
/* remaining bytes of DRAM */
A_UINT32 hi_dynamic_mem_remaining; /* 0x110 */
/* memory track count, configured by host */
A_UINT32 hi_dynamic_mem_track_max; /* 0x114 */
/* minidump buffer */
A_UINT32 hi_minidump; /* 0x118 */
/* bdata's sig and key addr */
A_UINT32 hi_bd_sig_key; /* 0x11c */
} POSTPACK64;
/* bitmap for hi_test_apps_related */
#define HI_TEST_APPS_TESTSCRIPT_LOADED 0x00000001
#define HI_TEST_APPS_CAL_DATA_AVAIL 0x00000002
/* Bits defined in hi_option_flag */
#define HI_OPTION_TIMER_WAR 0x01 /* Enable timer workaround */
#define HI_OPTION_BMI_CRED_LIMIT 0x02 /* Limit BMI command credits */
#define HI_OPTION_RELAY_DOT11_HDR 0x04 /* Relay Dot11 hdr to/from host */
#define HI_OPTION_MAC_ADDR_METHOD 0x08 /* MAC addr method 0-locally administred 1-globally unique addrs */
#define HI_OPTION_FW_BRIDGE 0x10 /* Firmware Bridging */
#define HI_OPTION_ENABLE_PROFILE 0x20 /* Enable CPU profiling */
#define HI_OPTION_DISABLE_DBGLOG 0x40 /* Disable debug logging */
#define HI_OPTION_SKIP_ERA_TRACKING 0x80 /* Skip Era Tracking */
#define HI_OPTION_PAPRD_DISABLE 0x100 /* Disable PAPRD (debug) */
#define HI_OPTION_NUM_DEV_LSB 0x200
#define HI_OPTION_NUM_DEV_MSB 0x800
#define HI_OPTION_DEV_MODE_LSB 0x1000
#define HI_OPTION_DEV_MODE_MSB 0x8000000
#define HI_OPTION_NO_LFT_STBL 0x10000000 /* Disable LowFreq Timer Stabilization */
#define HI_OPTION_SKIP_REG_SCAN 0x20000000 /* Skip regulatory scan */
#define HI_OPTION_INIT_REG_SCAN 0x40000000 /* Do regulatory scan during init before
* sending WMI ready event to host */
#define HI_OPTION_SKIP_MEMMAP 0x80000000 /* REV6: Do not adjust memory map */
#define HI_OPTION_MAC_ADDR_METHOD_SHIFT 3
/* 2 bits of hi_option_flag are used to represent 3 modes */
#define HI_OPTION_FW_MODE_IBSS 0x0 /* IBSS Mode */
#define HI_OPTION_FW_MODE_BSS_STA 0x1 /* STA Mode */
#define HI_OPTION_FW_MODE_AP 0x2 /* AP Mode */
#define HI_OPTION_FW_MODE_BT30AMP 0x3 /* BT30 AMP Mode */
/* 2 bits of hi_option flag are usedto represent 4 submodes */
#define HI_OPTION_FW_SUBMODE_NONE 0x0 /* Normal mode */
#define HI_OPTION_FW_SUBMODE_P2PDEV 0x1 /* p2p device mode */
#define HI_OPTION_FW_SUBMODE_P2PCLIENT 0x2 /* p2p client mode */
#define HI_OPTION_FW_SUBMODE_P2PGO 0x3 /* p2p go mode */
/* Num dev Mask */
#define HI_OPTION_NUM_DEV_MASK 0x7
#define HI_OPTION_NUM_DEV_SHIFT 0x9
/* firmware bridging */
#define HI_OPTION_FW_BRIDGE_SHIFT 0x04
/* Fw Mode/SubMode Mask
|-------------------------------------------------------------------------------|
| SUB | SUB | SUB | SUB | | | | |
| MODE[3] | MODE[2] | MODE[1] | MODE[0] | MODE[3] | MODE[2] | MODE[1] | MODE[0] |
| (2) | (2) | (2) | (2) | (2) | (2) | (2) | (2) |
|-------------------------------------------------------------------------------|
*/
#define HI_OPTION_FW_MODE_BITS 0x2
#define HI_OPTION_FW_MODE_MASK 0x3
#define HI_OPTION_FW_MODE_SHIFT 0xC
#define HI_OPTION_ALL_FW_MODE_MASK 0xFF
#define HI_OPTION_FW_SUBMODE_BITS 0x2
#define HI_OPTION_FW_SUBMODE_MASK 0x3
#define HI_OPTION_FW_SUBMODE_SHIFT 0x14
#define HI_OPTION_ALL_FW_SUBMODE_MASK 0xFF00
#define HI_OPTION_ALL_FW_SUBMODE_SHIFT 0x8
/* hi_option_flag2 options */
#define HI_OPTION_OFFLOAD_AMSDU 0x01
#define HI_OPTION_DFS_SUPPORT 0x02 /* Enable DFS support */
#define HI_OPTION_ENABLE_RFKILL 0x04 /* RFKill Enable Feature*/
#define HI_OPTION_RADIO_RETENTION_DISABLE 0x08 /* Disable radio retention */
#define HI_OPTION_EARLY_CFG_DONE 0x10 /* Early configuration is complete */
#define HI_OPTION_RF_KILL_SHIFT 0x2
#define HI_OPTION_RF_KILL_MASK 0x1
/* AR9888 1.0 only. Enable/disable CDC max perf support from host */
#define HI_OPTION_DISABLE_CDC_MAX_PERF_WAR 0x20
#define CDC_MAX_PERF_WAR_ENABLED() \
(!(HOST_INTEREST->hi_option_flag2 & HI_OPTION_DISABLE_CDC_MAX_PERF_WAR))
#define HI_OPTION_USE_EXT_LDO 0x40 /* use LDO27 for 1.1V instead of PMU */
#define HI_OPTION_DBUART_SUPPORT 0x80 /* Enable uart debug support */
#define HT_OPTION_GPIO_WAKEUP_SUPPORT 0x200 /* GPIO wake up support */
#define GPIO_WAKEUP_ENABLED() \
(HOST_INTEREST->hi_option_flag2 & HT_OPTION_GPIO_WAKEUP_SUPPORT)
/* hi_reset_flag */
#define HI_RESET_FLAG_PRESERVE_APP_START 0x01 /* preserve App Start address */
#define HI_RESET_FLAG_PRESERVE_HOST_INTEREST 0x02 /* preserve host interest */
#define HI_RESET_FLAG_PRESERVE_ROMDATA 0x04 /* preserve ROM data */
#define HI_RESET_FLAG_PRESERVE_NVRAM_STATE 0x08
#define HI_RESET_FLAG_PRESERVE_BOOT_INFO 0x10
#define HI_RESET_FLAG_WARM_RESET 0x20
/* define hi_fw_swap bits */
#define HI_DESC_IN_FW_BIT 0x01
#define HI_RESET_FLAG_IS_VALID 0x12345678 /* indicate the reset flag is valid */
#define ON_RESET_FLAGS_VALID() \
(HOST_INTEREST->hi_reset_flag_valid == HI_RESET_FLAG_IS_VALID)
#define RESET_FLAGS_VALIDATE() \
(HOST_INTEREST->hi_reset_flag_valid = HI_RESET_FLAG_IS_VALID)
#define RESET_FLAGS_INVALIDATE() \
(HOST_INTEREST->hi_reset_flag_valid = 0)
#define ON_RESET_PRESERVE_APP_START() \
(HOST_INTEREST->hi_reset_flag & HI_RESET_FLAG_PRESERVE_APP_START)
#define ON_RESET_PRESERVE_NVRAM_STATE() \
(HOST_INTEREST->hi_reset_flag & HI_RESET_FLAG_PRESERVE_NVRAM_STATE)
#define ON_RESET_PRESERVE_HOST_INTEREST() \
(HOST_INTEREST->hi_reset_flag & HI_RESET_FLAG_PRESERVE_HOST_INTEREST)
#define ON_RESET_PRESERVE_ROMDATA() \
(HOST_INTEREST->hi_reset_flag & HI_RESET_FLAG_PRESERVE_ROMDATA)
#define ON_RESET_PRESERVE_BOOT_INFO() \
(HOST_INTEREST->hi_reset_flag & HI_RESET_FLAG_PRESERVE_BOOT_INFO)
#define ON_RESET_WARM_RESET() \
(HOST_INTEREST->hi_reset_flag & HI_RESET_FLAG_WARM_RESET)
/* host CPU endianness */
#define HOST_ON_BE_CPU() \
(HOST_INTEREST->hi_be)
/* AP nart no swap descriptor flag. Decsriptors are created on the target processor. */
#define DESC_IN_FW() \
(HOST_INTEREST->hi_fw_swap & HI_DESC_IN_FW_BIT)
#define HI_ACS_FLAGS_SDIO_SWAP_MAILBOX_SET (1 << 0)
#define HI_ACS_FLAGS_SDIO_REDUCE_TX_COMPL_SET (1 << 1)
#define HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE (1 << 2)
#define HI_ACS_FLAGS_SDIO_SWAP_MAILBOX_FW_ACK (1 << 16)
#define HI_ACS_FLAGS_SDIO_REDUCE_TX_COMPL_FW_ACK (1 << 17)
/* CONSOLE FLAGS
*
* Bit Range Meaning
* --------- --------------------------------
* 2..0 UART ID (0 = Default)
* 3 Baud Select (0 = 9600, 1 = 115200)
* 30..4 Reserved
* 31 Enable Console
*
* */
#define HI_CONSOLE_FLAGS_ENABLE (1 << 31)
#define HI_CONSOLE_FLAGS_UART_MASK (0x7)
#define HI_CONSOLE_FLAGS_UART_SHIFT 0
#define HI_CONSOLE_FLAGS_BAUD_SELECT (1 << 3)
/* SM power save options */
#define HI_SMPS_ALLOW_MASK (0x00000001)
#define HI_SMPS_MODE_MASK (0x00000002)
#define HI_SMPS_MODE_STATIC (0x00000000)
#define HI_SMPS_MODE_DYNAMIC (0x00000002)
#define HI_SMPS_DISABLE_AUTO_MODE (0x00000004)
#define HI_SMPS_DATA_THRESH_MASK (0x000007f8)
#define HI_SMPS_DATA_THRESH_SHIFT (3)
#define HI_SMPS_RSSI_THRESH_MASK (0x0007f800)
#define HI_SMPS_RSSI_THRESH_SHIFT (11)
#define HI_SMPS_LOWPWR_CM_MASK (0x00380000)
#define HI_SMPS_LOWPWR_CM_SHIFT (15)
#define HI_SMPS_HIPWR_CM_MASK (0x03c00000)
#define HI_SMPS_HIPWR_CM_SHIFT (19)
#define HOST_INTEREST_SMPS_GET_MODE() (HOST_INTEREST->hi_smps_options & HI_SMPS_MODE_MASK)
#define HOST_INTEREST_SMPS_GET_DATA_THRESH() ((HOST_INTEREST->hi_smps_options & HI_SMPS_DATA_THRESH_MASK) >> HI_SMPS_DATA_THRESH_SHIFT)
#define HOST_INTEREST_SMPS_SET_DATA_THRESH(x) (((x) << HI_SMPS_DATA_THRESH_SHIFT) & HI_SMPS_DATA_THRESH_MASK)
#define HOST_INTEREST_SMPS_GET_RSSI_THRESH() ((HOST_INTEREST->hi_smps_options & HI_SMPS_RSSI_THRESH_MASK) >> HI_SMPS_RSSI_THRESH_SHIFT)
#define HOST_INTEREST_SMPS_SET_RSSI_THRESH(x) (((x) << HI_SMPS_RSSI_THRESH_SHIFT) & HI_SMPS_RSSI_THRESH_MASK)
#define HOST_INTEREST_SMPS_SET_LOWPWR_CM() ((HOST_INTEREST->hi_smps_options & HI_SMPS_LOWPWR_CM_MASK) >> HI_SMPS_LOWPWR_CM_SHIFT)
#define HOST_INTEREST_SMPS_SET_HIPWR_CM() ((HOST_INTEREST->hi_smps_options << HI_SMPS_HIPWR_CM_MASK) & HI_SMPS_HIPWR_CM_SHIFT)
#define HOST_INTEREST_SMPS_IS_AUTO_MODE_DISABLED() (HOST_INTEREST->hi_smps_options & HI_SMPS_DISABLE_AUTO_MODE)
/* WOW Extension configuration
*
* Bit Range Meaning
* --------- --------------------------------
* 8..0 Size of each WOW pattern (max 511)
* 15..9 Number of patterns per list (max 127)
* 17..16 Number of lists (max 4)
* 30..18 Reserved
* 31 Enabled
*
* set values (except enable) to zeros for default settings
*
* */
#define HI_WOW_EXT_ENABLED_MASK (1 << 31)
#define HI_WOW_EXT_NUM_LIST_SHIFT 16
#define HI_WOW_EXT_NUM_LIST_MASK (0x3 << HI_WOW_EXT_NUM_LIST_SHIFT)
#define HI_WOW_EXT_NUM_PATTERNS_SHIFT 9
#define HI_WOW_EXT_NUM_PATTERNS_MASK (0x7F << HI_WOW_EXT_NUM_PATTERNS_SHIFT)
#define HI_WOW_EXT_PATTERN_SIZE_SHIFT 0
#define HI_WOW_EXT_PATTERN_SIZE_MASK (0x1FF << HI_WOW_EXT_PATTERN_SIZE_SHIFT)
#define HI_WOW_EXT_MAKE_CONFIG(num_lists,count,size) \
((((num_lists) << HI_WOW_EXT_NUM_LIST_SHIFT) & HI_WOW_EXT_NUM_LIST_MASK) | \
(((count) << HI_WOW_EXT_NUM_PATTERNS_SHIFT) & HI_WOW_EXT_NUM_PATTERNS_MASK) | \
(((size) << HI_WOW_EXT_PATTERN_SIZE_SHIFT) & HI_WOW_EXT_PATTERN_SIZE_MASK))
#define HI_WOW_EXT_GET_NUM_LISTS(config) \
(((config) & HI_WOW_EXT_NUM_LIST_MASK) >> HI_WOW_EXT_NUM_LIST_SHIFT)
#define HI_WOW_EXT_GET_NUM_PATTERNS(config) \
(((config) & HI_WOW_EXT_NUM_PATTERNS_MASK) >> HI_WOW_EXT_NUM_PATTERNS_SHIFT)
#define HI_WOW_EXT_GET_PATTERN_SIZE(config) \
(((config) & HI_WOW_EXT_PATTERN_SIZE_MASK) >> HI_WOW_EXT_PATTERN_SIZE_SHIFT)
/*
* Early allocation configuration
* Support RAM bank configuration before BMI done and this eases the memory
* allocation at very early stage
* Bit Range Meaning
* --------- ----------------------------------
* [0:3] number of bank assigned to be IRAM
* [4:15] reserved
* [16:31] magic number
*
* Note:
* 1. target firmware would check magic number and if it's a match, firmware
* would consider the bits[0:15] are valid and base on that to calculate
* the end of DRAM. Early allocation would be located at that area and
* may be reclaimed when necesary
* 2. if no magic number is found, early allocation would happen at "_end"
* symbol of ROM which is located before the app-data and might NOT be
* re-claimable. If this is adopted, link script should keep this in
* mind to avoid data corruption.
*/
#define HI_EARLY_ALLOC_MAGIC 0x6d8a
#define HI_EARLY_ALLOC_MAGIC_MASK 0xffff0000
#define HI_EARLY_ALLOC_MAGIC_SHIFT 16
#define HI_EARLY_ALLOC_IRAM_BANKS_MASK 0x0000000f
#define HI_EARLY_ALLOC_IRAM_BANKS_SHIFT 0
#define HI_EARLY_ALLOC_VALID() \
((((HOST_INTEREST->hi_early_alloc) & HI_EARLY_ALLOC_MAGIC_MASK) >> HI_EARLY_ALLOC_MAGIC_SHIFT) \
== (HI_EARLY_ALLOC_MAGIC))
#define HI_EARLY_ALLOC_GET_IRAM_BANKS() \
(((HOST_INTEREST->hi_early_alloc) & HI_EARLY_ALLOC_IRAM_BANKS_MASK) >> HI_EARLY_ALLOC_IRAM_BANKS_SHIFT)
/*
* Intended for use by Host software, this macro returns the Target RAM
* address of any item in the host_interest structure.
* Example: target_addr = AR6002_HOST_INTEREST_ITEM_ADDRESS(hi_board_data);
*/
#define AR6002_HOST_INTEREST_ITEM_ADDRESS(item) \
(A_UINT32)((size_t)&((((struct host_interest_s *)(AR6002_HOST_INTEREST_ADDRESS))->item)))
#define AR6003_HOST_INTEREST_ITEM_ADDRESS(item) \
(A_UINT32)((size_t)&((((struct host_interest_s *)(AR6003_HOST_INTEREST_ADDRESS))->item)))
#define AR6004_HOST_INTEREST_ITEM_ADDRESS(item) \
(A_UINT32)((size_t)&((((struct host_interest_s *)(AR6004_HOST_INTEREST_ADDRESS))->item)))
#define AR6006_HOST_INTEREST_ITEM_ADDRESS(item) \
(A_UINT32)((size_t)&((((struct host_interest_s *)(AR6006_HOST_INTEREST_ADDRESS))->item)))
#define AR9888_HOST_INTEREST_ITEM_ADDRESS(item) \
(A_UINT32)((size_t)&((((struct host_interest_s *)(AR9888_HOST_INTEREST_ADDRESS))->item)))
#define AR6320_HOST_INTEREST_ITEM_ADDRESS(item) \
(A_UINT32)((size_t)&((((struct host_interest_s *)(AR6320_HOST_INTEREST_ADDRESS))->item)))
#define AR900B_HOST_INTEREST_ITEM_ADDRESS(item) \
(A_UINT32)((size_t)&((((struct host_interest_s *)(AR900B_HOST_INTEREST_ADDRESS))->item)))
#define HOST_INTEREST_DBGLOG_IS_ENABLED() \
(!((volatile A_UINT32)HOST_INTEREST->hi_option_flag & HI_OPTION_DISABLE_DBGLOG))
#define HOST_INTEREST_PKTLOG_IS_ENABLED() \
(((volatile A_UINT32)HOST_INTEREST->hi_pktlog_num_buffers))
#define HOST_INTEREST_PROFILE_IS_ENABLED() \
((volatile A_UINT32)HOST_INTEREST->hi_option_flag & HI_OPTION_ENABLE_PROFILE)
#define LF_TIMER_STABILIZATION_IS_ENABLED() \
(!((volatile A_UINT32)HOST_INTEREST->hi_option_flag & HI_OPTION_NO_LFT_STBL))
#define IS_AMSDU_OFFLAOD_ENABLED() \
(((volatile A_UINT32)HOST_INTEREST->hi_option_flag2 & HI_OPTION_OFFLOAD_AMSDU))
#define HOST_INTEREST_DFS_IS_ENABLED() \
(((volatile A_UINT32)HOST_INTEREST->hi_option_flag2 & HI_OPTION_DFS_SUPPORT))
#define HOST_INTEREST_EARLY_CFG_DONE() \
(((volatile A_UINT32)HOST_INTEREST->hi_option_flag2 & HI_OPTION_EARLY_CFG_DONE))
/*power save flag bit definitions*/
#define HI_PWR_SAVE_LPL_ENABLED 0x1
/*b1-b3 reserved*/
/*b4-b5 : dev0 LPL type : 0 - none
1- Reduce Pwr Search
2- Reduce Pwr Listen*/
/*b6-b7 : dev1 LPL type and so on for Max 8 devices*/
#define HI_PWR_SAVE_LPL_DEV0_LSB 4
#define HI_PWR_SAVE_LPL_DEV_MASK 0x3
/*power save related utility macros*/
#define HI_LPL_ENABLED() \
((HOST_INTEREST->hi_pwr_save_flags & HI_PWR_SAVE_LPL_ENABLED))
#define HI_DEV_LPL_TYPE_GET(_devix) \
(HOST_INTEREST->hi_pwr_save_flags & \
((HI_PWR_SAVE_LPL_DEV_MASK) << \
(HI_PWR_SAVE_LPL_DEV0_LSB + \
(_devix)*2)))
#define HOST_INTEREST_SMPS_IS_ALLOWED() \
((HOST_INTEREST->hi_smps_options & HI_SMPS_ALLOW_MASK))
/* Convert a Target virtual address into a Target physical address */
#define AR6002_VTOP(vaddr) ((vaddr) & 0x001fffff)
#define AR6003_VTOP(vaddr) ((vaddr) & 0x001fffff)
#define AR6004_VTOP(vaddr) (vaddr)
#define AR6006_VTOP(vaddr) (vaddr)
#define AR9888_VTOP(vaddr) (vaddr)
#define AR6320_VTOP(vaddr) (vaddr)
#define AR900B_VTOP(vaddr) (vaddr)
#define TARG_VTOP(TargetType, vaddr) \
(((TargetType) == TARGET_TYPE_AR6002) ? AR6002_VTOP(vaddr) : \
(((TargetType) == TARGET_TYPE_AR6003) ? AR6003_VTOP(vaddr) : \
(((TargetType) == TARGET_TYPE_AR6004) ? AR6004_VTOP(vaddr) : \
(((TargetType) == TARGET_TYPE_AR6006) ? AR6006_VTOP(vaddr) : \
(((TargetType) == TARGET_TYPE_AR9888) ? AR9888_VTOP(vaddr) : \
(((TargetType) == TARGET_TYPE_AR6320) ? AR6320_VTOP(vaddr) : \
(((TargetType) == TARGET_TYPE_AR900B) ? AR900B_VTOP(vaddr) : \
0)))))))
#define HOST_INTEREST_ITEM_ADDRESS(TargetType, item) \
(((TargetType) == TARGET_TYPE_AR6002) ? AR6002_HOST_INTEREST_ITEM_ADDRESS(item) : \
(((TargetType) == TARGET_TYPE_AR6003) ? AR6003_HOST_INTEREST_ITEM_ADDRESS(item) : \
(((TargetType) == TARGET_TYPE_AR6004) ? AR6004_HOST_INTEREST_ITEM_ADDRESS(item) : \
(((TargetType) == TARGET_TYPE_AR6006) ? AR6006_HOST_INTEREST_ITEM_ADDRESS(item) : \
(((TargetType) == TARGET_TYPE_AR9888) ? AR9888_HOST_INTEREST_ITEM_ADDRESS(item) : \
(((TargetType) == TARGET_TYPE_AR6320) ? AR6320_HOST_INTEREST_ITEM_ADDRESS(item) : \
(((TargetType) == TARGET_TYPE_AR6320V2) ? AR6320_HOST_INTEREST_ITEM_ADDRESS(item) : \
(((TargetType) == TARGET_TYPE_AR900B) ? AR900B_HOST_INTEREST_ITEM_ADDRESS(item) : \
0))))))))
#define AR6002_BOARD_DATA_SZ 768
#define AR6002_BOARD_EXT_DATA_SZ 0
#define AR6003_BOARD_DATA_SZ 1024
/* Reserve 1024 bytes for extended board data */
#if defined(AR6002_REV43)
#define AR6003_BOARD_EXT_DATA_SZ 1024
#else
#define AR6003_BOARD_EXT_DATA_SZ 768
#endif
#define AR6004_BOARD_DATA_SZ 7168
#define AR6004_BOARD_EXT_DATA_SZ 0
#define AR9888_BOARD_DATA_SZ 7168
#define AR9888_BOARD_EXT_DATA_SZ 0
#define AR6320_BOARD_DATA_SZ 8192
#define AR6320_BOARD_EXT_DATA_SZ 0
#define AR900B_BOARD_DATA_SZ 7168
#define AR900B_BOARD_EXT_DATA_SZ 0
#define AR6003_REV3_APP_START_OVERRIDE 0x946100
#define AR6003_REV3_APP_LOAD_ADDRESS 0x545000
#define AR6003_REV3_BOARD_EXT_DATA_ADDRESS 0x542330
#define AR6003_REV3_DATASET_PATCH_ADDRESS 0x57FF74
#define AR6003_REV3_RAM_RESERVE_SIZE 4096
#define AR6004_REV1_BOARD_DATA_ADDRESS 0x423900
#define AR6004_REV1_RAM_RESERVE_SIZE 19456
#define AR6004_REV1_DATASET_PATCH_ADDRESS 0x425294
#define AR6004_REV2_BOARD_DATA_ADDRESS 0x426400
#define AR6004_REV2_RAM_RESERVE_SIZE 7168
#define AR6004_REV2_DATASET_PATCH_ADDRESS 0x435294
#define AR6004_REV5_BOARD_DATA_ADDRESS 0x436400
#define AR6004_REV5_RAM_RESERVE_SIZE 7168
#define AR6004_REV5_DATASET_PATCH_ADDRESS 0x437860
/* Reserve 4K for OTA test script */
#define AR6004_REV1_RAM_RESERVE_SIZE_FOR_TEST_SCRIPT 4096
#define AR6004_REV1_TEST_SCRIPT_ADDRESS 0x422900
/* # of A_UINT32 entries in targregs, used by DIAG_FETCH_TARG_REGS */
#define AR6003_FETCH_TARG_REGS_COUNT 64
#define AR6004_FETCH_TARG_REGS_COUNT 64
#define AR9888_FETCH_TARG_REGS_COUNT 64
#define AR6320_FETCH_TARG_REGS_COUNT 64
#define AR900B_FETCH_TARG_REGS_COUNT 64
#endif /* !__ASSEMBLER__ */
#ifndef ATH_TARGET
#include "athendpack.h"
#endif
#endif /* __TARGADDRS_H__ */