| /* |
| * Copyright (C) 2016 Freescale Semiconductor, Inc. |
| * Copyright 2017 NXP |
| * |
| * SPDX-License-Identifier: BSD-3-Clause |
| */ |
| |
| /*! |
| * Header file containing the public API for the System Controller (SC) |
| * Power Management (PM) function. This includes functions for power state |
| * control, clock control, reset control, and wake-up event control. |
| * |
| * @addtogroup PM_SVC (SVC) Power Management Service |
| * |
| * Module for the Power Management (PM) service. |
| * |
| * @{ |
| */ |
| |
| #ifndef _SC_PM_API_H |
| #define _SC_PM_API_H |
| |
| /* Includes */ |
| |
| #include <sci/types.h> |
| #include <sci/svc/rm/api.h> |
| |
| /* Defines */ |
| |
| /*! |
| * @name Defines for type widths |
| */ |
| /*@{*/ |
| #define SC_PM_POWER_MODE_W 2 /*!< Width of sc_pm_power_mode_t */ |
| #define SC_PM_CLOCK_MODE_W 3 /*!< Width of sc_pm_clock_mode_t */ |
| #define SC_PM_RESET_TYPE_W 2 /*!< Width of sc_pm_reset_type_t */ |
| #define SC_PM_RESET_REASON_W 3 /*!< Width of sc_pm_reset_reason_t */ |
| /*@}*/ |
| |
| /*! |
| * @name Defines for clock indexes (sc_pm_clk_t) |
| */ |
| /*@{*/ |
| /*@}*/ |
| |
| /*! |
| * @name Defines for ALL parameters |
| */ |
| /*@{*/ |
| #define SC_PM_CLK_ALL UINT8_MAX /*!< All clocks */ |
| /*@}*/ |
| |
| /*! |
| * @name Defines for sc_pm_power_mode_t |
| */ |
| /*@{*/ |
| #define SC_PM_PW_MODE_OFF 0 /*!< Power off */ |
| #define SC_PM_PW_MODE_STBY 1 /*!< Power in standby */ |
| #define SC_PM_PW_MODE_LP 2 /*!< Power in low-power */ |
| #define SC_PM_PW_MODE_ON 3 /*!< Power on */ |
| /*@}*/ |
| |
| /*! |
| * @name Defines for sc_pm_clk_t |
| */ |
| /*@{*/ |
| #define SC_PM_CLK_SLV_BUS 0 /*!< Slave bus clock */ |
| #define SC_PM_CLK_MST_BUS 1 /*!< Master bus clock */ |
| #define SC_PM_CLK_PER 2 /*!< Peripheral clock */ |
| #define SC_PM_CLK_PHY 3 /*!< Phy clock */ |
| #define SC_PM_CLK_MISC 4 /*!< Misc clock */ |
| #define SC_PM_CLK_MISC0 0 /*!< Misc 0 clock */ |
| #define SC_PM_CLK_MISC1 1 /*!< Misc 1 clock */ |
| #define SC_PM_CLK_MISC2 2 /*!< Misc 2 clock */ |
| #define SC_PM_CLK_MISC3 3 /*!< Misc 3 clock */ |
| #define SC_PM_CLK_MISC4 4 /*!< Misc 4 clock */ |
| #define SC_PM_CLK_CPU 2 /*!< CPU clock */ |
| #define SC_PM_CLK_PLL 4 /*!< PLL */ |
| #define SC_PM_CLK_BYPASS 4 /*!< Bypass clock */ |
| /*@}*/ |
| |
| /*! |
| * @name Defines for sc_pm_clk_mode_t |
| */ |
| /*@{*/ |
| #define SC_PM_CLK_MODE_ROM_INIT 0 /*!< Clock is initialized by ROM. */ |
| #define SC_PM_CLK_MODE_OFF 1 /*!< Clock is disabled */ |
| #define SC_PM_CLK_MODE_ON 2 /*!< Clock is enabled. */ |
| #define SC_PM_CLK_MODE_AUTOGATE_SW 3 /*!< Clock is in SW autogate mode */ |
| #define SC_PM_CLK_MODE_AUTOGATE_HW 4 /*!< Clock is in HW autogate mode */ |
| #define SC_PM_CLK_MODE_AUTOGATE_SW_HW 5 /*!< Clock is in SW-HW autogate mode */ |
| /*@}*/ |
| |
| /*! |
| * @name Defines for sc_pm_clk_parent_t |
| */ |
| /*@{*/ |
| #define SC_PM_PARENT_XTAL 0 /*!< Parent is XTAL. */ |
| #define SC_PM_PARENT_PLL0 1 /*!< Parent is PLL0 */ |
| #define SC_PM_PARENT_PLL1 2 /*!< Parent is PLL1 or PLL0/2 */ |
| #define SC_PM_PARENT_PLL2 3 /*!< Parent in PLL2 or PLL0/4 */ |
| #define SC_PM_PARENT_BYPS 4 /*!< Parent is a bypass clock. */ |
| /*@}*/ |
| |
| /*! |
| * @name Defines for sc_pm_reset_type_t |
| */ |
| /*@{*/ |
| #define SC_PM_RESET_TYPE_COLD 0 /*!< Cold reset */ |
| #define SC_PM_RESET_TYPE_WARM 1 /*!< Warm reset */ |
| #define SC_PM_RESET_TYPE_BOARD 2 /*!< Board reset */ |
| /*@}*/ |
| |
| /*! |
| * @name Defines for sc_pm_reset_reason_t |
| */ |
| /*@{*/ |
| #define SC_PM_RESET_REASON_POR 0 /*!< Power on reset */ |
| #define SC_PM_RESET_REASON_WARM 1 /*!< Warm reset */ |
| #define SC_PM_RESET_REASON_SW 2 /*!< Software reset */ |
| #define SC_PM_RESET_REASON_WDOG 3 /*!< Watchdog reset */ |
| #define SC_PM_RESET_REASON_LOCKUP 4 /*!< Lockup reset */ |
| #define SC_PM_RESET_REASON_TAMPER 5 /*!< Tamper reset */ |
| #define SC_PM_RESET_REASON_TEMP 6 /*!< Temp reset */ |
| #define SC_PM_RESET_REASON_LOW_VOLT 7 /*!< Low voltage reset */ |
| /*@}*/ |
| |
| /*! |
| * @name Defines for sc_pm_sys_if_t |
| */ |
| /*@{*/ |
| #define SC_PM_SYS_IF_INTERCONNECT 0 /*!< System interconnect */ |
| #define SC_PM_SYS_IF_MU 1 /*!< AP -> SCU message units */ |
| #define SC_PM_SYS_IF_OCMEM 2 /*!< On-chip memory (ROM/OCRAM) */ |
| #define SC_PM_SYS_IF_DDR 3 /*!< DDR memory */ |
| /*@}*/ |
| |
| /* Types */ |
| |
| /*! |
| * This type is used to declare a power mode. Note resources only use |
| * SC_PM_PW_MODE_OFF and SC_PM_PW_MODE_ON. The other modes are used only |
| * as system power modes. |
| */ |
| typedef uint8_t sc_pm_power_mode_t; |
| |
| /*! |
| * This type is used to declare a clock. |
| */ |
| typedef uint8_t sc_pm_clk_t; |
| |
| /*! |
| * This type is used to declare a clock mode. |
| */ |
| typedef uint8_t sc_pm_clk_mode_t; |
| |
| /*! |
| * This type is used to declare the clock parent. |
| */ |
| typedef uint8_t sc_pm_clk_parent_t; |
| |
| /*! |
| * This type is used to declare clock rates. |
| */ |
| typedef uint32_t sc_pm_clock_rate_t; |
| |
| /*! |
| * This type is used to declare a desired reset type. |
| */ |
| typedef uint8_t sc_pm_reset_type_t; |
| |
| /*! |
| * This type is used to declare a reason for a reset. |
| */ |
| typedef uint8_t sc_pm_reset_reason_t; |
| |
| /*! |
| * This type is used to specify a system-level interface to be power managed. |
| */ |
| typedef uint8_t sc_pm_sys_if_t; |
| |
| /* Functions */ |
| |
| /*! |
| * @name Power Functions |
| * @{ |
| */ |
| |
| /*! |
| * This function sets the system power mode. Only the owner of the |
| * SC_R_SYSTEM resource can do this. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] mode power mode to apply |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid mode, |
| * - SC_ERR_NOACCESS if caller not the owner of SC_R_SYSTEM |
| * |
| * @see sc_pm_set_sys_power_mode(). |
| */ |
| sc_err_t sc_pm_set_sys_power_mode(sc_ipc_t ipc, sc_pm_power_mode_t mode); |
| |
| /*! |
| * This function sets the power mode of a partition. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] pt handle of partition |
| * @param[in] mode power mode to apply |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid partition or mode, |
| * - SC_ERR_NOACCESS if caller's partition is not the owner or |
| * parent of \a pt |
| * |
| * All resources owned by \a pt that are on will have their power |
| * mode changed to \a mode. |
| * |
| * @see sc_pm_set_partition_power_mode(). |
| */ |
| sc_err_t sc_pm_set_partition_power_mode(sc_ipc_t ipc, sc_rm_pt_t pt, |
| sc_pm_power_mode_t mode); |
| |
| /*! |
| * This function gets the power mode of a partition. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] pt handle of partition |
| * @param[out] mode pointer to return power mode |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid partition |
| */ |
| sc_err_t sc_pm_get_sys_power_mode(sc_ipc_t ipc, sc_rm_pt_t pt, |
| sc_pm_power_mode_t *mode); |
| |
| /*! |
| * This function sets the power mode of a resource. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] resource ID of the resource |
| * @param[in] mode power mode to apply |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid resource or mode, |
| * - SC_ERR_NOACCESS if caller's partition is not the resource owner |
| * or parent of the owner |
| * |
| * Resources set to SC_PM_PW_MODE_ON will reflect the |
| * power mode of the partition and will change as that changes. |
| * |
| * Note some resources are still not accessible even when powered up if bus |
| * transactions go through a fabric not powered up. Examples of this are |
| * resources in display and capture subsystems which require the display |
| * controller or the imaging subsytem to be powered up first. |
| * |
| * @see sc_pm_set_sys_power_mode(). |
| */ |
| sc_err_t sc_pm_set_resource_power_mode(sc_ipc_t ipc, sc_rsrc_t resource, |
| sc_pm_power_mode_t mode); |
| |
| /*! |
| * This function gets the power mode of a resource. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] resource ID of the resource |
| * @param[out] mode pointer to return power mode |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Note only SC_PM_PW_MODE_OFF and SC_PM_PW_MODE_ON are valid. The value |
| * returned does not reflect the power mode of the partition.. |
| */ |
| sc_err_t sc_pm_get_resource_power_mode(sc_ipc_t ipc, sc_rsrc_t resource, |
| sc_pm_power_mode_t *mode); |
| |
| /*! |
| * This function requests the low power mode some of the resources |
| * can enter based on their state. This API is only valid for the |
| * following resources : SC_R_A53, SC_R_A53_0, SC_R_A53_1, SC_A53_2, |
| * SC_A53_3, SC_R_A72, SC_R_A72_0, SC_R_A72_1, SC_R_CC1, SC_R_A35, |
| * SC_R_A35_0, SC_R_A35_1, SC_R_A35_2, SC_R_A35_3. |
| * For all other resources it will return SC_ERR_PARAM. |
| * This function will set the low power mode the cores, cluster |
| * and cluster associated resources will enter when all the cores |
| * in a given cluster execute WFI |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] resource ID of the resource |
| * @param[out] mode pointer to return power mode |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| */ |
| sc_err_t sc_pm_req_low_power_mode(sc_ipc_t ipc, sc_rsrc_t resource, |
| sc_pm_power_mode_t mode); |
| |
| /*! |
| * This function is used to set the resume address of a CPU. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] resource ID of the CPU resource |
| * @param[in] address 64-bit resume address |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid resource or address, |
| * - SC_ERR_NOACCESS if caller's partition is not the parent of the |
| * resource (CPU) owner |
| */ |
| sc_err_t sc_pm_set_cpu_resume_addr(sc_ipc_t ipc, sc_rsrc_t resource, |
| sc_faddr_t address); |
| |
| /*! |
| * This function requests the power mode configuration for system-level |
| * interfaces including messaging units, interconnect, and memories. This API |
| * is only valid for the following resources : SC_R_A53, SC_R_A72, and |
| * SC_R_M4_x_PID_y. For all other resources, it will return SC_ERR_PARAM. |
| * The requested power mode will be captured and applied to system-level |
| * resources as system conditions allow. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] resource ID of the resource |
| * @param[in] sys_if system-level interface to be configured |
| * @param[in] hpm high-power mode for the system interface |
| * @param[in] lpm low-power mode for the system interface |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| */ |
| sc_err_t sc_pm_req_sys_if_power_mode(sc_ipc_t ipc, sc_rsrc_t resource, |
| sc_pm_sys_if_t sys_if, sc_pm_power_mode_t hpm, sc_pm_power_mode_t lpm); |
| |
| /* @} */ |
| |
| /*! |
| * @name Clock/PLL Functions |
| * @{ |
| */ |
| |
| /*! |
| * This function sets the rate of a resource's clock/PLL. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] resource ID of the resource |
| * @param[in] clk clock/PLL to affect |
| * @param[in,out] rate pointer to rate to set, |
| * return actual rate |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid resource or clock/PLL, |
| * - SC_ERR_NOACCESS if caller's partition is not the resource owner |
| * or parent of the owner, |
| * - SC_ERR_UNAVAILABLE if clock/PLL not applicable to this resource, |
| * - SC_ERR_LOCKED if rate locked (usually because shared clock/PLL) |
| * |
| * Refer to the [Clock List](@ref CLOCKS) for valid clock/PLL values. |
| */ |
| sc_err_t sc_pm_set_clock_rate(sc_ipc_t ipc, sc_rsrc_t resource, |
| sc_pm_clk_t clk, sc_pm_clock_rate_t *rate); |
| |
| /*! |
| * This function gets the rate of a resource's clock/PLL. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] resource ID of the resource |
| * @param[in] clk clock/PLL to affect |
| * @param[out] rate pointer to return rate |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid resource or clock/PLL, |
| * - SC_ERR_NOACCESS if caller's partition is not the resource owner |
| * or parent of the owner, |
| * - SC_ERR_UNAVAILABLE if clock/PLL not applicable to this resource |
| * |
| * Refer to the [Clock List](@ref CLOCKS) for valid clock/PLL values. |
| */ |
| sc_err_t sc_pm_get_clock_rate(sc_ipc_t ipc, sc_rsrc_t resource, |
| sc_pm_clk_t clk, sc_pm_clock_rate_t *rate); |
| |
| /*! |
| * This function enables/disables a resource's clock. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] resource ID of the resource |
| * @param[in] clk clock to affect |
| * @param[in] enable enable if true; otherwise disabled |
| * @param[in] autog HW auto clock gating |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid resource or clock, |
| * - SC_ERR_NOACCESS if caller's partition is not the resource owner |
| * or parent of the owner, |
| * - SC_ERR_UNAVAILABLE if clock not applicable to this resource |
| * |
| * Refer to the [Clock List](@ref CLOCKS) for valid clock values. |
| */ |
| sc_err_t sc_pm_clock_enable(sc_ipc_t ipc, sc_rsrc_t resource, |
| sc_pm_clk_t clk, bool enable, bool autog); |
| |
| /*! |
| * This function sets the parent of a resource's clock. |
| * This function should only be called when the clock is disabled. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] resource ID of the resource |
| * @param[in] clk clock to affect |
| * @param[in] parent New parent of the clock. |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid resource or clock, |
| * - SC_ERR_NOACCESS if caller's partition is not the resource owner |
| * or parent of the owner, |
| * - SC_ERR_UNAVAILABLE if clock not applicable to this resource |
| * - SC_ERR_BUSY if clock is currently enabled. |
| * |
| * Refer to the [Clock List](@ref CLOCKS) for valid clock values. |
| */ |
| sc_err_t sc_pm_set_clock_parent(sc_ipc_t ipc, sc_rsrc_t resource, |
| sc_pm_clk_t clk, sc_pm_clk_parent_t parent); |
| |
| /*! |
| * This function gets the parent of a resource's clock. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] resource ID of the resource |
| * @param[in] clk clock to affect |
| * @param[out] parent pointer to return parent of clock. |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid resource or clock, |
| * - SC_ERR_NOACCESS if caller's partition is not the resource owner |
| * or parent of the owner, |
| * - SC_ERR_UNAVAILABLE if clock not applicable to this resource |
| * |
| * Refer to the [Clock List](@ref CLOCKS) for valid clock values. |
| */ |
| sc_err_t sc_pm_get_clock_parent(sc_ipc_t ipc, sc_rsrc_t resource, |
| sc_pm_clk_t clk, sc_pm_clk_parent_t *parent); |
| |
| /* @} */ |
| |
| /*! |
| * @name Reset Functions |
| * @{ |
| */ |
| |
| /*! |
| * This function is used to reset the system. Only the owner of the |
| * SC_R_SYSTEM resource can do this. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] type reset type |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid type |
| * |
| * If this function returns, then the reset did not occur due to an |
| * invalid parameter. |
| */ |
| sc_err_t sc_pm_reset(sc_ipc_t ipc, sc_pm_reset_type_t type); |
| |
| /*! |
| * This function gets a caller's reset reason. |
| * |
| * @param[in] ipc IPC handle |
| * @param[out] reason pointer to return reset reason |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| */ |
| sc_err_t sc_pm_reset_reason(sc_ipc_t ipc, sc_pm_reset_reason_t *reason); |
| |
| /*! |
| * This function is used to boot a partition. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] pt handle of partition to boot |
| * @param[in] resource_cpu ID of the CPU resource to start |
| * @param[in] boot_addr 64-bit boot address |
| * @param[in] resource_mu ID of the MU that must be powered |
| * @param[in] resource_dev ID of the boot device that must be powered |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid partition, resource, or addr, |
| * - SC_ERR_NOACCESS if caller's partition is not the parent of the |
| * partition to boot |
| */ |
| sc_err_t sc_pm_boot(sc_ipc_t ipc, sc_rm_pt_t pt, |
| sc_rsrc_t resource_cpu, sc_faddr_t boot_addr, |
| sc_rsrc_t resource_mu, sc_rsrc_t resource_dev); |
| |
| /*! |
| * This function is used to reboot the caller's partition. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] type reset type |
| * |
| * If \a type is SC_PM_RESET_TYPE_COLD, then most peripherals owned by |
| * the calling partition will be reset if possible. SC state (partitions, |
| * power, clocks, etc.) is reset. The boot SW of the booting CPU must be |
| * able to handle peripherals that that are not reset. |
| * |
| * If \a type is SC_PM_RESET_TYPE_WARM, then only the boot CPU is reset. |
| * SC state (partitions, power, clocks, etc.) are NOT reset. The boot SW |
| * of the booting CPU must be able to handle peripherals and SC state that |
| * that are not reset. |
| * |
| * If \a type is SC_PM_RESET_TYPE_BOARD, then return with no action. |
| * |
| * If this function returns, then the reset did not occur due to an |
| * invalid parameter. |
| */ |
| void sc_pm_reboot(sc_ipc_t ipc, sc_pm_reset_type_t type); |
| |
| /*! |
| * This function is used to reboot a partition. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] pt handle of partition to reboot |
| * @param[in] type reset type |
| * |
| * If \a type is SC_PM_RESET_TYPE_COLD, then most peripherals owned by |
| * the calling partition will be reset if possible. SC state (partitions, |
| * power, clocks, etc.) is reset. The boot SW of the booting CPU must be |
| * able to handle peripherals that that are not reset. |
| * |
| * If \a type is SC_PM_RESET_TYPE_WARM, then only the boot CPU is reset. |
| * SC state (partitions, power, clocks, etc.) are NOT reset. The boot SW |
| * of the booting CPU must be able to handle peripherals and SC state that |
| * that are not reset. |
| * |
| * If \a type is SC_PM_RESET_TYPE_BOARD, then return with no action. |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid partition or type |
| * - SC_ERR_NOACCESS if caller's partition is not the parent of \a pt, |
| * |
| * Most peripherals owned by the partition will be reset if |
| * possible. SC state (partitions, power, clocks, etc.) is reset. The |
| * boot SW of the booting CPU must be able to handle peripherals that |
| * that are not reset. |
| */ |
| sc_err_t sc_pm_reboot_partition(sc_ipc_t ipc, sc_rm_pt_t pt, |
| sc_pm_reset_type_t type); |
| |
| /*! |
| * This function is used to start/stop a CPU. |
| * |
| * @param[in] ipc IPC handle |
| * @param[in] resource ID of the CPU resource |
| * @param[in] enable start if true; otherwise stop |
| * @param[in] address 64-bit boot address |
| * |
| * @return Returns an error code (SC_ERR_NONE = success). |
| * |
| * Return errors: |
| * - SC_ERR_PARM if invalid resource or address, |
| * - SC_ERR_NOACCESS if caller's partition is not the parent of the |
| * resource (CPU) owner |
| */ |
| sc_err_t sc_pm_cpu_start(sc_ipc_t ipc, sc_rsrc_t resource, bool enable, |
| sc_faddr_t address); |
| |
| /* @} */ |
| |
| #endif /* _SC_PM_API_H */ |
| |
| /**@}*/ |