| Getty |
| |
| ??? Should getty open tty with or without O_NONBLOCK? |
| For serial lines, it means "should getty wait for Carrier Detect pin?" |
| I checked other getties: |
| |
| - agetty always uses O_NONBLOCK |
| - mgetty uses O_NONBLOCK unless run with -b, or as "getty" |
| |
| ??? If we decided to use O_NONBLOCK (perhaps optionally with -b), |
| when getty should send -I INITSTR data to tty? After open succeeds? |
| What if we also want to initialize *modem* with some AT commands? |
| |
| ??? Should we check/create /var/lock/LCK..ttyPFX lockfiles? |
| |
| ??? mgetty opens tty but does NOT lock it, then waits for input via |
| select/poll, and when input is available, it checks lock file. |
| If it exists, mgetty exits (it assumes someone else uses the line). |
| If no, it creates the file (lock the tty). Sounds like a good algorithm |
| to use if we are called with -w... |
| |
| Getty should establish a new session and process group, and ensure |
| that tty is a ctty. |
| |
| ??? Should getty ensure that other processes which might have opened |
| fds to this tty be disconnected? agetty has a -R option which makes |
| agetty call vhangup() after tty is opened. (Then agetty opens it again, |
| since it probably vhangup'ed its own fd too). |
| |
| Getty should leave the tty in approximately the same state as "stty sane" |
| before it execs login program. Minor things we do conditionally are: |
| c_iflag |= ICRNL; // if '\r' was used to end username |
| |
| ??? mgetty uses per-tty file to ignore connects, /etc/nologin.ttyxx - |
| is it useful? |
| |
| It should be possible to run "getty 0 -" from a shell prompt. |
| [This currently doesn't work from interactive shell since setsid() |
| fails in process group leader. The workaround is to run it as a child |
| of something. sh -c 'getty - 0; true' usually works. Should we fix this?] |
| It should leave tty in a sane state when it exits (Ctrl-D, -t SEC timeout): |
| echo should be on, speed, control chars properly set, etc. |
| (However, it can't restore ctty. The symptom is that "</dev/tty" |
| fails in the parent shell after getty exits: /dev/tty can't be opened). |
| |
| Getty should write LOGIN_PROCESS utmp record before it starts waiting |
| for username to be entered. |
| |
| Login |
| |
| Login should not try to set up tty parameters - apart from switching echo |
| off while entering password, and switching it back on after. |
| |
| Login should not leave "echo off" state when it times out reading password |
| or otherwise terminates (Ctrl-C, Ctrl-D etc). |
| |
| ??? Should login establish a new session and/or process group, and ensure |
| that tty is a ctty? Without this, running login directly (not via getty) |
| from e.g. initscript will usually result with a login session without |
| ctty and without session/pgrp properly created... |
| |
| It should be possible to run "login [USER]" from a shell prompt, |
| and it should work (not block/die/error out). |
| Similarly to getty, it should leave tty in the sane state when it exits. |
| |
| ??? Should login write LOGIN_PROCESS utmp record before it starts waiting |
| for username/password to be entered? |
| |
| Login should write USER_PROCESS utmp record just before it is about |
| to exec user's shell. |
