blob: 67412136eeba1760b2d117fb1f468eb1a0168d38 [file] [log] [blame]
Atmel AT91 Evaluation kits
Index
- I. Board mapping & boot media
- II. NAND partition table
- III. watchdog support
I. Board mapping & boot media
------------------------------------------------------------------------------
AT91SAM9260EK, AT91SAM9G20EK & AT91SAM9XEEK
------------------------------------------------------------------------------
Memory map
0x20000000 - 23FFFFFF SDRAM (64 MB)
0xC0000000 - Cxxxxxxx Atmel Dataflash card (J13)
0xD0000000 - D07FFFFF Soldered Atmel Dataflash (AT45DB642)
Environment variables
U-Boot environment variables can be stored at different places:
- Dataflash on SPI chip select 1 (default)
- Dataflash on SPI chip select 0 (dataflash card)
- Nand flash.
You can choose your storage location at config step (here for at91sam9260ek) :
make at91sam9260ek_nandflash_config - use nand flash
make at91sam9260ek_dataflash_cs0_config - use data flash (spi cs0)
make at91sam9260ek_dataflash_cs1_config - use data flash (spi cs1)
------------------------------------------------------------------------------
AT91SAM9261EK, AT91SAM9G10EK
------------------------------------------------------------------------------
Memory map
0x20000000 - 23FFFFFF SDRAM (64 MB)
0xC0000000 - C07FFFFF Soldered Atmel Dataflash (AT45DB642)
0xD0000000 - Dxxxxxxx Atmel Dataflash card (J22)
Environment variables
U-Boot environment variables can be stored at different places:
- Dataflash on SPI chip select 0 (default)
- Dataflash on SPI chip select 3 (dataflash card)
- Nand flash.
You can choose your storage location at config step (here for at91sam9260ek) :
make at91sam9261ek_nandflash_config - use nand flash
make at91sam9261ek_dataflash_cs0_config - use data flash (spi cs0)
make at91sam9261ek_dataflash_cs3_config - use data flash (spi cs3)
------------------------------------------------------------------------------
AT91SAM9263EK
------------------------------------------------------------------------------
Memory map
0x20000000 - 23FFFFFF SDRAM (64 MB)
0xC0000000 - Cxxxxxxx Atmel Dataflash card (J9)
Environment variables
U-Boot environment variables can be stored at different places:
- Dataflash on SPI chip select 0 (dataflash card)
- Nand flash.
- Nor flash (not populate by default)
You can choose your storage location at config step (here for at91sam9260ek) :
make at91sam9263ek_nandflash_config - use nand flash
make at91sam9263ek_dataflash_cs0_config - use data flash (spi cs0)
make at91sam9263ek_norflash_config - use nor flash
You can choose to boot directly from U-Boot at config step
make at91sam9263ek_norflash_boot_config - boot from nor flash
------------------------------------------------------------------------------
AT91SAM9M10G45EK
------------------------------------------------------------------------------
Memory map
0x70000000 - 77FFFFFF SDRAM (128 MB)
Environment variables
U-Boot environment variables can be stored at different places:
- Nand flash.
You can choose your storage location at config step (here for at91sam9m10g45ek) :
make at91sam9m10g45ek_nandflash_config - use nand flash
------------------------------------------------------------------------------
AT91SAM9RLEK
------------------------------------------------------------------------------
Memory map
0x20000000 - 23FFFFFF SDRAM (64 MB)
0xC0000000 - C07FFFFF Soldered Atmel Dataflash (AT45DB642)
Environment variables
U-Boot environment variables can be stored at different places:
- Dataflash on SPI chip select 0
- Nand flash.
You can choose your storage location at config step (here for at91sam9rlek) :
make at91sam9rlek_nandflash_config - use nand flash
------------------------------------------------------------------------------
AT91SAM9N12EK, AT91SAM9X5EK
------------------------------------------------------------------------------
Memory map
0x20000000 - 27FFFFFF SDRAM (128 MB)
Environment variables
U-Boot environment variables can be stored at different places:
- Nand flash.
- SD/MMC card
- Serialflash/Dataflash on SPI chip select 0
You can choose your storage location at config step (here for at91sam9x5ek) :
make at91sam9x5ek_dataflash_config - use data flash
make at91sam9x5ek_mmc_config - use sd/mmc card
make at91sam9x5ek_nandflash_config - use nand flash
make at91sam9x5ek_spiflash_config - use serial flash
------------------------------------------------------------------------------
SAMA5D3XEK
------------------------------------------------------------------------------
Memory map
0x20000000 - 3FFFFFFF SDRAM (512 MB)
Environment variables
U-Boot environment variables can be stored at different places:
- Nand flash.
- SD/MMC card
- Serialflash on SPI chip select 0
You can choose your storage location at config step (here for sama5d3xek) :
make sama5d3xek_mmc_config - use SD/MMC card
make sama5d3xek_nandflash_config - use nand flash
make sama5d3xek_serialflash_config - use serial flash
II. NAND partition table
All the board support boot from NAND flash will use the following NAND
partition table
0x00000000 - 0x0003FFFF bootstrap (256 KiB)
0x00040000 - 0x000BFFFF u-boot (512 KiB)
0x000C0000 - 0x000FFFFF env (256 KiB)
0x00100000 - 0x0013FFFF env_redundant (256 KiB)
0x00140000 - 0x0017FFFF spare (256 KiB)
0x00180000 - 0x001FFFFF dtb (512 KiB)
0x00200000 - 0x007FFFFF kernel (6 MiB)
0x00800000 - 0xxxxxxxxx rootfs (All left)
III. Watchdog support
For security reasons, the at91 watchdog is running at boot time and,
if deactivated, cannot be used anymore.
If you want to use the watchdog, you will need to keep it running in
your code (make sure not to disable it in AT91Bootstrap for instance).
In the U-Boot configuration, the AT91 watchdog support is enabled using
the CONFIG_AT91SAM9_WATCHDOG and CONFIG_HW_WATCHDOG options.