blob: ccc2f9c09d19ef30e5e6215c5b7958d175a694c4 [file] [log] [blame]
/*
* Copyright 2014 Freescale Semiconductor, Inc.
*
* Configuration settings for the Freescale i.MX6SX Sabresd board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include "mx6_common.h"
#define CONFIG_DBG_MONITOR
#ifdef CONFIG_SPL
#include "imx6_spl.h"
#endif
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART1_BASE
#ifdef CONFIG_IMX_BOOTAUX
/* Set to QSPI2 B flash at default */
#ifdef CONFIG_DM_SPI
#define CONFIG_SYS_AUXCORE_BOOTDATA 0x78000000
#define SF_QSPI2_B_CS_NUM 2
#elif defined(CONFIG_MX6SX_SABRESD_REVA)
#define CONFIG_SYS_AUXCORE_BOOTDATA 0x71000000
#define SF_QSPI2_B_CS_NUM 1
#else
#define CONFIG_SYS_AUXCORE_BOOTDATA 0x72000000
#define SF_QSPI2_B_CS_NUM 1
#endif
/* When using M4 fastup demo, no need these M4 env, since QSPI is used by M4 */
#ifndef CONFIG_SYS_AUXCORE_FASTUP
#define UPDATE_M4_ENV \
"m4image=m4_qspi.bin\0" \
"m4_qspi_cs="__stringify(SF_QSPI2_B_CS_NUM)"\0" \
"loadm4image=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4image}\0" \
"update_m4_from_sd=" \
"if sf probe 1:${m4_qspi_cs}; then " \
"if run loadm4image; then " \
"setexpr fw_sz ${filesize} + 0xffff; " \
"setexpr fw_sz ${fw_sz} / 0x10000; " \
"setexpr fw_sz ${fw_sz} * 0x10000; " \
"sf erase 0x0 ${fw_sz}; " \
"sf write ${loadaddr} 0x0 ${filesize}; " \
"fi; " \
"fi\0" \
"m4boot=sf probe 1:${m4_qspi_cs}; bootaux "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)"\0"
#else
#define UPDATE_M4_ENV ""
#endif /* CONFIG_SYS_AUXCORE_FASTUP */
#else
#define UPDATE_M4_ENV ""
#endif /* CONFIG_IMX_BOOTAUX */
#define CONFIG_MFG_ENV_SETTINGS \
"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
"rdinit=/linuxrc " \
"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
"g_mass_storage.file=/fat g_mass_storage.ro=1 " \
"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
"g_mass_storage.iSerialNumber=\"\" "\
"\0" \
"initrd_addr=0x83800000\0" \
"initrd_high=0xffffffff\0" \
"bootcmd_mfg=run mfgtool_args; " \
"if test ${tee} = yes; then " \
"bootm ${tee_addr} ${initrd_addr} ${fdt_addr}; " \
"else " \
"bootz ${loadaddr} ${initrd_addr} ${fdt_addr}; " \
"fi;\0"
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_MFG_ENV_SETTINGS \
UPDATE_M4_ENV \
TEE_ENV \
"script=boot.scr\0" \
"image=zImage\0" \
"console=ttymxc0\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
"fdt_file=imx6sx-sdb.dtb\0" \
"fdt_addr=0x83000000\0" \
"tee_addr=0x84000000\0" \
"tee_file=uTee-6sxsdb\0" \
"boot_fdt=try\0" \
"ip_dyn=yes\0" \
"panel=Hannstar-XGA\0" \
"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
"mmcpart=1\0" \
"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
"mmcautodetect=yes\0" \
"mmcargs=setenv bootargs console=${console},${baudrate} " \
"root=${mmcroot}\0" \
"loadbootscript=" \
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"loadtee=fatload mmc ${mmcdev}:${mmcpart} ${tee_addr} ${tee_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${tee} = yes; then " \
"run loadfdt; run loadtee; bootm ${tee_addr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
"bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
"bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
"bootz; " \
"fi; " \
"fi;\0" \
"netargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/nfs " \
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"netboot=echo Booting from net ...; " \
"run netargs; " \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"${get_cmd} ${image}; " \
"if test ${tee} = yes; then " \
"${get_cmd} ${tee_addr} ${tee_file}; " \
"${get_cmd} ${fdt_addr} ${fdt_file}; " \
"bootm ${tee_addr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
"bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
"bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
"bootz; " \
"fi; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev};" \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
"if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
"fi; " \
"else run netboot; fi"
/* Miscellaneous configurable options */
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x10000)
#define CONFIG_STACKSIZE SZ_128K
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#ifdef CONFIG_SYS_AUXCORE_FASTUP
/* #define CONFIG_IMX_RDC */ /* Disable the RDC temporarily, will enable it in future */
#define CONFIG_ENV_IS_IN_MMC /* Must disable QSPI driver, because M4 run on QSPI */
#elif defined CONFIG_QSPI_BOOT
#define CONFIG_ENV_IS_IN_SPI_FLASH
#else
#define CONFIG_ENV_IS_IN_MMC
#endif
/* MMC Configuration */
#define CONFIG_SYS_FSL_USDHC_NUM 3
#define CONFIG_SYS_MMC_ENV_DEV 2 /*USDHC4*/
#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */
#define CONFIG_MMCROOT "/dev/mmcblk3p2" /* USDHC4 */
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC4_BASE_ADDR
/* I2C Configs */
#ifndef CONFIG_DM_I2C
#define CONFIG_SYS_I2C
#endif
#ifdef CONFIG_CMD_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED 100000
#endif
/* PMIC */
#ifndef CONFIG_DM_PMIC
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_PFUZE100
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
#endif
/* Network */
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define CONFIG_FEC_ENET_DEV 1
#if (CONFIG_FEC_ENET_DEV == 0)
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
#ifdef CONFIG_DM_ETH
#define CONFIG_ETHPRIME "eth0"
#else
#define CONFIG_ETHPRIME "FEC0"
#endif
#elif (CONFIG_FEC_ENET_DEV == 1)
#define IMX_FEC_BASE ENET2_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x2
#ifdef CONFIG_DM_ETH
#define CONFIG_ETHPRIME "eth1"
#else
#define CONFIG_ETHPRIME "FEC1"
#endif
#endif
#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS
#define CONFIG_FEC_MXC_MDIO_BASE ENET_BASE_ADDR
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#endif
/*
* The PCIe support in uboot would bring failures in i.MX6SX PCIe
* EP/RC validations. Disable PCIe support in uboot here.
* RootCause: The bit10(ltssm_en) of GPR12 would be set in uboot,
* thus the i.MX6SX PCIe EP would be cheated that the other i.MX6SX
* PCIe RC had been configured and trying to setup PCIe link directly,
* although the i.MX6SX RC is not properly configured at that time.
* PCIe can be supported in uboot, if the i.MX6SX PCIe EP/RC validation
* is not running.
*/
#ifdef CONFIG_PCI
#define CONFIG_CMD_PCI
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_PCIE_IMX
#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(2, 0)
#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(2, 1)
#endif
#define CONFIG_IMX_THERMAL
#ifdef CONFIG_FSL_QSPI
#define CONFIG_SYS_FSL_QSPI_AHB
#ifdef CONFIG_MX6SX_SABRESD_REVA
#define FSL_QSPI_FLASH_SIZE SZ_16M
#else
#define FSL_QSPI_FLASH_SIZE SZ_32M
#endif
#define FSL_QSPI_FLASH_NUM 2
#define CONFIG_SF_DEFAULT_BUS 1
#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 40000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#endif
#define CONFIG_CMD_BMODE
#ifndef CONFIG_SPL_BUILD
#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_MXS
#define CONFIG_VIDEO_LOGO
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_CMD_BMP
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IMX_VIDEO_SKIP
#define CONFIG_SYS_CONSOLE_BG_COL 0x00
#define CONFIG_SYS_CONSOLE_FG_COL 0xa0
#endif
#endif
#define CONFIG_ENV_SIZE SZ_8K
#if defined(CONFIG_ENV_IS_IN_MMC)
#define CONFIG_ENV_OFFSET (14 * SZ_64K)
#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
#define CONFIG_ENV_OFFSET (896 * 1024)
#define CONFIG_ENV_SECT_SIZE (64 * 1024)
#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#endif
#define CONFIG_SYS_FSL_USDHC_NUM 3
#if defined(CONFIG_ANDROID_SUPPORT)
#include "mx6sxsabresdandroid.h"
#endif
#endif /* __CONFIG_H */