blob: 34901aa3c904228c2e5c68835e4936bb06b2eec7 [file] [log] [blame]
/**
* Copyright 2011 Freescale Semiconductor
* Author: Mingkai Hu <Mingkai.hu@freescale.com>
*
* SPDX-License-Identifier: GPL-2.0+
*
* This file provides support for the board-specific CPLD used on some Freescale
* reference boards.
*
* The following macros need to be defined:
*
* CPLD_BASE - The virtual address of the base of the CPLD register map
*/
#include <common.h>
#include <command.h>
#include <asm/io.h>
#include "cpld.h"
static u8 __cpld_read(unsigned int reg)
{
void *p = (void *)CPLD_BASE;
return in_8(p + reg);
}
u8 cpld_read(unsigned int reg) __attribute__((weak, alias("__cpld_read")));
static void __cpld_write(unsigned int reg, u8 value)
{
void *p = (void *)CPLD_BASE;
out_8(p + reg, value);
}
void cpld_write(unsigned int reg, u8 value)
__attribute__((weak, alias("__cpld_write")));
/*
* Reset the board. This honors the por_cfg registers.
*/
void __cpld_reset(void)
{
CPLD_WRITE(system_rst, 1);
}
void cpld_reset(void) __attribute__((weak, alias("__cpld_reset")));
/**
* Set the boot bank to the alternate bank
*/
void __cpld_set_altbank(void)
{
u8 reg5 = CPLD_READ(sw_ctl_on);
CPLD_WRITE(sw_ctl_on, reg5 | CPLD_SWITCH_BANK_ENABLE);
CPLD_WRITE(fbank_sel, 1);
CPLD_WRITE(system_rst, 1);
}
void cpld_set_altbank(void)
__attribute__((weak, alias("__cpld_set_altbank")));
/**
* Set the boot bank to the default bank
*/
void __cpld_set_defbank(void)
{
CPLD_WRITE(system_rst_default, 1);
}
void cpld_set_defbank(void)
__attribute__((weak, alias("__cpld_set_defbank")));
#ifdef DEBUG
static void cpld_dump_regs(void)
{
printf("cpld_ver = 0x%02x\n", CPLD_READ(cpld_ver));
printf("cpld_ver_sub = 0x%02x\n", CPLD_READ(cpld_ver_sub));
printf("pcba_ver = 0x%02x\n", CPLD_READ(pcba_ver));
printf("system_rst = 0x%02x\n", CPLD_READ(system_rst));
printf("sw_ctl_on = 0x%02x\n", CPLD_READ(sw_ctl_on));
printf("por_cfg = 0x%02x\n", CPLD_READ(por_cfg));
printf("switch_strobe = 0x%02x\n", CPLD_READ(switch_strobe));
printf("jtag_sel = 0x%02x\n", CPLD_READ(jtag_sel));
printf("sdbank1_clk = 0x%02x\n", CPLD_READ(sdbank1_clk));
printf("sdbank2_clk = 0x%02x\n", CPLD_READ(sdbank2_clk));
printf("fbank_sel = 0x%02x\n", CPLD_READ(fbank_sel));
printf("serdes_mux = 0x%02x\n", CPLD_READ(serdes_mux));
printf("SW[2] = 0x%02x\n", in_8(&CPLD_SW(2)));
putc('\n');
}
#endif
int cpld_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
int rc = 0;
if (argc <= 1)
return cmd_usage(cmdtp);
if (strcmp(argv[1], "reset") == 0) {
if (strcmp(argv[2], "altbank") == 0)
cpld_set_altbank();
else
cpld_set_defbank();
} else if (strcmp(argv[1], "lane_mux") == 0) {
u32 lane = simple_strtoul(argv[2], NULL, 16);
u8 val = (u8)simple_strtoul(argv[3], NULL, 16);
u8 reg = CPLD_READ(serdes_mux);
switch (lane) {
case 0x6:
reg &= ~SERDES_MUX_LANE_6_MASK;
reg |= val << SERDES_MUX_LANE_6_SHIFT;
break;
case 0xa:
reg &= ~SERDES_MUX_LANE_A_MASK;
reg |= val << SERDES_MUX_LANE_A_SHIFT;
break;
case 0xc:
reg &= ~SERDES_MUX_LANE_C_MASK;
reg |= val << SERDES_MUX_LANE_C_SHIFT;
break;
case 0xd:
reg &= ~SERDES_MUX_LANE_D_MASK;
reg |= val << SERDES_MUX_LANE_D_SHIFT;
break;
default:
printf("Invalid value\n");
break;
}
CPLD_WRITE(serdes_mux, reg);
#ifdef DEBUG
} else if (strcmp(argv[1], "dump") == 0) {
cpld_dump_regs();
#endif
} else
rc = cmd_usage(cmdtp);
return rc;
}
U_BOOT_CMD(
cpld_cmd, CONFIG_SYS_MAXARGS, 1, cpld_cmd,
"Reset the board or pin mulexing selection using the CPLD sequencer",
"reset - hard reset to default bank\n"
"cpld_cmd reset altbank - reset to alternate bank\n"
"cpld_cmd lane_mux <lane> <mux_value> - set multiplexed lane pin\n"
" lane 6: 0 -> slot1\n"
" 1 -> SGMII (Default)\n"
" lane a: 0 -> slot2\n"
" 1 -> AURORA (Default)\n"
" lane c: 0 -> slot2\n"
" 1 -> SATA0 (Default)\n"
" lane d: 0 -> slot2\n"
" 1 -> SATA1 (Default)\n"
#ifdef DEBUG
"cpld_cmd dump - display the CPLD registers\n"
#endif
);