blob: 29f29bb2d28513e4edf020c0e6abb6e7fa55e211 [file] [log] [blame]
/*
* Copyright (C) 2016 Freescale Semiconductor, Inc.
* Copyright 2017 NXP
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
#include <asm/imx-common/boot_mode.h>
#include <asm/io.h>
#include <common.h>
#include <linux/sizes.h>
#include <mmc.h>
#include <mxsfb.h>
#include <power/pmic.h>
#include <power/pfuze100_pmic.h>
#include "../common/pfuze.h"
#if defined(CONFIG_MXC_EPDC)
#include <lcd.h>
#include <mxc_epdc_fb.h>
#endif
#include <asm/imx-common/video.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define LCD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm)
#define EPDC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
return 0;
}
static iomux_v3_cfg_t const uart1_pads[] = {
MX6_PAD_UART1_TXD__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_UART1_RXD__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const wdog_pads[] = {
MX6_PAD_WDOG_B__WDOG1_B | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}
#ifdef CONFIG_DM_PMIC_PFUZE100
int power_init_board(void)
{
struct udevice *dev;
int ret;
u32 dev_id, rev_id, i;
u32 switch_num = 6;
u32 offset = PFUZE100_SW1CMODE;
ret = pmic_get("pfuze100", &dev);
if (ret == -ENODEV)
return 0;
if (ret != 0)
return ret;
dev_id = pmic_reg_read(dev, PFUZE100_DEVICEID);
rev_id = pmic_reg_read(dev, PFUZE100_REVID);
printf("PMIC: PFUZE100! DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
/* Init mode to APS_PFM */
pmic_reg_write(dev, PFUZE100_SW1ABMODE, APS_PFM);
for (i = 0; i < switch_num - 1; i++)
pmic_reg_write(dev, offset + i * SWITCH_SIZE, APS_PFM);
/* set SW1AB staby volatage 0.975V */
pmic_clrsetbits(dev, PFUZE100_SW1ABSTBY, 0x3f, 0x1b);
/* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
pmic_clrsetbits(dev, PFUZE100_SW1ABCONF, 0xc0, 0x40);
/* set SW1C staby volatage 0.975V */
pmic_clrsetbits(dev, PFUZE100_SW1CSTBY, 0x3f, 0x1b);
/* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */
pmic_clrsetbits(dev, PFUZE100_SW1CCONF, 0xc0, 0x40);
return 0;
}
#endif
#ifdef CONFIG_VIDEO_MXS
static iomux_v3_cfg_t const lcd_pads[] = {
MX6_PAD_LCD_CLK__LCD_CLK | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_ENABLE__LCD_ENABLE | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_HSYNC__LCD_HSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_VSYNC__LCD_VSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA00__LCD_DATA00 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA01__LCD_DATA01 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA02__LCD_DATA02 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA03__LCD_DATA03 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA04__LCD_DATA04 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA05__LCD_DATA05 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA06__LCD_DATA06 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA07__LCD_DATA07 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA08__LCD_DATA08 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA09__LCD_DATA09 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA10__LCD_DATA10 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA11__LCD_DATA11 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA12__LCD_DATA12 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA13__LCD_DATA13 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA14__LCD_DATA14 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA15__LCD_DATA15 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA16__LCD_DATA16 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA17__LCD_DATA17 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA18__LCD_DATA18 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA19__LCD_DATA19 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA20__LCD_DATA20 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA21__LCD_DATA21 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA22__LCD_DATA22 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_LCD_DATA23__LCD_DATA23 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX6_PAD_KEY_ROW5__GPIO4_IO03 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_LCD_RESET__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* Use GPIO for Brightness adjustment, duty cycle = period */
MX6_PAD_PWM1__GPIO3_IO23 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
void do_enable_parallel_lcd(struct display_info_t const *dev)
{
int ret;
ret = enable_lcdif_clock(dev->bus, 1);
if (ret) {
printf("Enable LCDIF clock failed, %d\n", ret);
return;
}
imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
/* Reset the LCD */
gpio_request(IMX_GPIO_NR(2, 19), "lcd reset");
gpio_direction_output(IMX_GPIO_NR(2, 19) , 0);
udelay(500);
gpio_direction_output(IMX_GPIO_NR(2, 19) , 1);
gpio_request(IMX_GPIO_NR(4, 3), "lcd pwr en");
gpio_direction_output(IMX_GPIO_NR(4, 3) , 1);
/* Set Brightness to high */
gpio_request(IMX_GPIO_NR(3, 23), "backlight");
gpio_direction_output(IMX_GPIO_NR(3, 23) , 1);
}
struct display_info_t const displays[] = {{
.bus = MX6SLL_LCDIF_BASE_ADDR,
.addr = 0,
.pixfmt = 24,
.detect = NULL,
.enable = do_enable_parallel_lcd,
.mode = {
.name = "MCIMX28LCD",
.xres = 800,
.yres = 480,
.pixclock = 29850,
.left_margin = 89,
.right_margin = 164,
.upper_margin = 23,
.lower_margin = 10,
.hsync_len = 10,
.vsync_len = 10,
.sync = 0,
.vmode = FB_VMODE_NONINTERLACED
} } };
size_t display_count = ARRAY_SIZE(displays);
#endif
#ifdef CONFIG_MXC_EPDC
static iomux_v3_cfg_t const epdc_enable_pads[] = {
MX6_PAD_EPDC_DATA00__EPDC_DATA00 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA01__EPDC_DATA01 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA02__EPDC_DATA02 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA03__EPDC_DATA03 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA04__EPDC_DATA04 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA05__EPDC_DATA05 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA06__EPDC_DATA06 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA07__EPDC_DATA07 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA08__EPDC_DATA08 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA09__EPDC_DATA09 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA10__EPDC_DATA10 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA11__EPDC_DATA11 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA12__EPDC_DATA12 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA13__EPDC_DATA13 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA14__EPDC_DATA14 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_DATA15__EPDC_DATA15 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_SDCLK__EPDC_SDCLK_P | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_SDLE__EPDC_SDLE | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_SDOE__EPDC_SDOE | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_SDSHR__EPDC_SDSHR | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_SDCE0__EPDC_SDCE0 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_GDCLK__EPDC_GDCLK | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_GDOE__EPDC_GDOE | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_GDRL__EPDC_GDRL | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX6_PAD_EPDC_GDSP__EPDC_GDSP | MUX_PAD_CTRL(EPDC_PAD_CTRL),
};
static iomux_v3_cfg_t const epdc_disable_pads[] = {
MX6_PAD_EPDC_DATA01__GPIO1_IO08,
MX6_PAD_EPDC_DATA02__GPIO1_IO09,
MX6_PAD_EPDC_DATA03__GPIO1_IO10,
MX6_PAD_EPDC_DATA04__GPIO1_IO11,
MX6_PAD_EPDC_DATA05__GPIO1_IO12,
MX6_PAD_EPDC_DATA06__GPIO1_IO13,
MX6_PAD_EPDC_DATA07__GPIO1_IO14,
MX6_PAD_EPDC_DATA08__GPIO1_IO15,
MX6_PAD_EPDC_DATA09__GPIO1_IO16,
MX6_PAD_EPDC_DATA10__GPIO1_IO17,
MX6_PAD_EPDC_DATA11__GPIO1_IO18,
MX6_PAD_EPDC_DATA12__GPIO1_IO19,
MX6_PAD_EPDC_DATA13__GPIO1_IO20,
MX6_PAD_EPDC_DATA14__GPIO1_IO21,
MX6_PAD_EPDC_DATA15__GPIO1_IO22,
MX6_PAD_EPDC_SDCLK__GPIO1_IO23,
MX6_PAD_EPDC_SDLE__GPIO1_IO24,
MX6_PAD_EPDC_SDOE__GPIO1_IO25,
MX6_PAD_EPDC_SDSHR__GPIO1_IO26,
MX6_PAD_EPDC_SDCE0__GPIO1_IO27,
MX6_PAD_EPDC_GDCLK__GPIO1_IO31,
MX6_PAD_EPDC_GDOE__GPIO2_IO00,
MX6_PAD_EPDC_GDRL__GPIO2_IO01,
MX6_PAD_EPDC_GDSP__GPIO2_IO02,
};
vidinfo_t panel_info = {
.vl_refresh = 85,
.vl_col = 1024,
.vl_row = 758,
.vl_pixclock = 40000000,
.vl_left_margin = 12,
.vl_right_margin = 76,
.vl_upper_margin = 4,
.vl_lower_margin = 5,
.vl_hsync = 12,
.vl_vsync = 2,
.vl_sync = 0,
.vl_mode = 0,
.vl_flag = 0,
.vl_bpix = 3,
.cmap = 0,
};
struct epdc_timing_params panel_timings = {
.vscan_holdoff = 4,
.sdoed_width = 10,
.sdoed_delay = 20,
.sdoez_width = 10,
.sdoez_delay = 20,
.gdclk_hp_offs = 524,
.gdsp_offs = 327,
.gdoe_offs = 0,
.gdclk_offs = 19,
.num_ce = 1,
};
static void setup_epdc_power(void)
{
/* Setup epdc voltage */
/* EPDC_PWRSTAT - GPIO2[13] for PWR_GOOD status */
imx_iomux_v3_setup_pad(MX6_PAD_EPDC_PWR_STAT__GPIO2_IO13 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
gpio_request(IMX_GPIO_NR(2, 13), "epdc_pwrstat");
gpio_direction_input(IMX_GPIO_NR(2, 13));
/* EPDC_VCOM0 - GPIO2[03] for VCOM control */
imx_iomux_v3_setup_pad(MX6_PAD_EPDC_VCOM0__GPIO2_IO03 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* Set as output */
gpio_request(IMX_GPIO_NR(2, 3), "epdc_vcom0");
gpio_direction_output(IMX_GPIO_NR(2, 3), 1);
/* EPDC_PWRWAKEUP - GPIO2[14] for EPD PMIC WAKEUP */
imx_iomux_v3_setup_pad(MX6_PAD_EPDC_PWR_WAKE__GPIO2_IO14 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* Set as output */
gpio_request(IMX_GPIO_NR(2, 14), "epdc_pwr_wake");
gpio_direction_output(IMX_GPIO_NR(2, 14), 1);
/* EPDC_PWRCTRL0 - GPIO2[07] for EPD PWR CTL0 */
imx_iomux_v3_setup_pad(MX6_PAD_EPDC_PWR_CTRL0__GPIO2_IO07 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* Set as output */
gpio_request(IMX_GPIO_NR(2, 7), "epdc_pwr_ctrl0");
gpio_direction_output(IMX_GPIO_NR(2, 7), 1);
}
static void epdc_enable_pins(void)
{
/* epdc iomux settings */
imx_iomux_v3_setup_multiple_pads(epdc_enable_pads,
ARRAY_SIZE(epdc_enable_pads));
}
static void epdc_disable_pins(void)
{
/* Configure MUX settings for EPDC pins to GPIO and drive to 0 */
imx_iomux_v3_setup_multiple_pads(epdc_disable_pads,
ARRAY_SIZE(epdc_disable_pads));
}
static void setup_epdc(void)
{
/*** epdc Maxim PMIC settings ***/
/* EPDC_PWRSTAT - GPIO2[13] for PWR_GOOD status */
imx_iomux_v3_setup_pad(MX6_PAD_EPDC_PWR_STAT__GPIO2_IO13 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* EPDC_VCOM0 - GPIO2[03] for VCOM control */
imx_iomux_v3_setup_pad(MX6_PAD_EPDC_VCOM0__GPIO2_IO03 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* EPDC_PWRWAKEUP - GPIO2[14] for EPD PMIC WAKEUP */
imx_iomux_v3_setup_pad(MX6_PAD_EPDC_PWR_WAKE__GPIO2_IO14 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* EPDC_PWRCTRL0 - GPIO2[07] for EPD PWR CTL0 */
imx_iomux_v3_setup_pad(MX6_PAD_EPDC_PWR_CTRL0__GPIO2_IO07 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* Set pixel clock rates for EPDC in clock.c */
panel_info.epdc_data.wv_modes.mode_init = 0;
panel_info.epdc_data.wv_modes.mode_du = 1;
panel_info.epdc_data.wv_modes.mode_gc4 = 3;
panel_info.epdc_data.wv_modes.mode_gc8 = 2;
panel_info.epdc_data.wv_modes.mode_gc16 = 2;
panel_info.epdc_data.wv_modes.mode_gc32 = 2;
panel_info.epdc_data.epdc_timings = panel_timings;
setup_epdc_power();
}
void epdc_power_on(void)
{
unsigned int reg;
struct gpio_regs *gpio_regs = (struct gpio_regs *)GPIO2_BASE_ADDR;
/* Set EPD_PWR_CTL0 to high - enable EINK_VDD (3.15) */
gpio_set_value(IMX_GPIO_NR(2, 7), 1);
udelay(1000);
/* Enable epdc signal pin */
epdc_enable_pins();
/* Set PMIC Wakeup to high - enable Display power */
gpio_set_value(IMX_GPIO_NR(2, 14), 1);
/* Wait for PWRGOOD == 1 */
while (1) {
reg = readl(&gpio_regs->gpio_psr);
if (!(reg & (1 << 13)))
break;
udelay(100);
}
/* Enable VCOM */
gpio_set_value(IMX_GPIO_NR(2, 3), 1);
udelay(500);
}
void epdc_power_off(void)
{
/* Set PMIC Wakeup to low - disable Display power */
gpio_set_value(IMX_GPIO_NR(2, 14), 0);
/* Disable VCOM */
gpio_set_value(IMX_GPIO_NR(2, 3), 0);
epdc_disable_pins();
/* Set EPD_PWR_CTL0 to low - disable EINK_VDD (3.15) */
gpio_set_value(IMX_GPIO_NR(2, 7), 0);
}
#endif
int board_early_init_f(void)
{
setup_iomux_uart();
return 0;
}
int board_init(void)
{
/* Address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_MXC_EPDC
enable_epdc_clock();
setup_epdc();
#endif
return 0;
}
int board_late_init(void)
{
setenv("tee", "no");
#ifdef CONFIG_IMX_OPTEE
setenv("tee", "yes");
#endif
#ifdef CONFIG_ENV_IS_IN_MMC
board_late_mmc_env_init();
#endif
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
set_wdog_reset((struct wdog_regs *)WDOG1_BASE_ADDR);
return 0;
}
int checkboard(void)
{
puts("Board: MX6SLL EVK\n");
return 0;
}
int board_mmc_get_env_dev(int devno)
{
return devno;
}
int mmc_map_to_kernel_blk(int devno)
{
return devno;
}