| /* |
| * (C) Copyright 2004-2010 |
| * Texas Instruments, <www.ti.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| #ifndef _OMAP2PLUS_I2C_H_ |
| #define _OMAP2PLUS_I2C_H_ |
| |
| /* I2C masks */ |
| |
| /* I2C Interrupt Enable Register (I2C_IE): */ |
| #define I2C_IE_GC_IE (1 << 5) |
| #define I2C_IE_XRDY_IE (1 << 4) /* Transmit data ready interrupt enable */ |
| #define I2C_IE_RRDY_IE (1 << 3) /* Receive data ready interrupt enable */ |
| #define I2C_IE_ARDY_IE (1 << 2) /* Register access ready interrupt enable */ |
| #define I2C_IE_NACK_IE (1 << 1) /* No acknowledgment interrupt enable */ |
| #define I2C_IE_AL_IE (1 << 0) /* Arbitration lost interrupt enable */ |
| |
| /* I2C Status Register (I2C_STAT): */ |
| |
| #define I2C_STAT_SBD (1 << 15) /* Single byte data */ |
| #define I2C_STAT_BB (1 << 12) /* Bus busy */ |
| #define I2C_STAT_ROVR (1 << 11) /* Receive overrun */ |
| #define I2C_STAT_XUDF (1 << 10) /* Transmit underflow */ |
| #define I2C_STAT_AAS (1 << 9) /* Address as slave */ |
| #define I2C_STAT_GC (1 << 5) |
| #define I2C_STAT_XRDY (1 << 4) /* Transmit data ready */ |
| #define I2C_STAT_RRDY (1 << 3) /* Receive data ready */ |
| #define I2C_STAT_ARDY (1 << 2) /* Register access ready */ |
| #define I2C_STAT_NACK (1 << 1) /* No acknowledgment interrupt enable */ |
| #define I2C_STAT_AL (1 << 0) /* Arbitration lost interrupt enable */ |
| |
| /* I2C Interrupt Code Register (I2C_INTCODE): */ |
| |
| #define I2C_INTCODE_MASK 7 |
| #define I2C_INTCODE_NONE 0 |
| #define I2C_INTCODE_AL 1 /* Arbitration lost */ |
| #define I2C_INTCODE_NAK 2 /* No acknowledgement/general call */ |
| #define I2C_INTCODE_ARDY 3 /* Register access ready */ |
| #define I2C_INTCODE_RRDY 4 /* Rcv data ready */ |
| #define I2C_INTCODE_XRDY 5 /* Xmit data ready */ |
| |
| /* I2C Buffer Configuration Register (I2C_BUF): */ |
| |
| #define I2C_BUF_RDMA_EN (1 << 15) /* Receive DMA channel enable */ |
| #define I2C_BUF_XDMA_EN (1 << 7) /* Transmit DMA channel enable */ |
| |
| /* I2C Configuration Register (I2C_CON): */ |
| |
| #define I2C_CON_EN (1 << 15) /* I2C module enable */ |
| #define I2C_CON_BE (1 << 14) /* Big endian mode */ |
| #define I2C_CON_STB (1 << 11) /* Start byte mode (master mode only) */ |
| #define I2C_CON_MST (1 << 10) /* Master/slave mode */ |
| #define I2C_CON_TRX (1 << 9) /* Transmitter/receiver mode */ |
| /* (master mode only) */ |
| #define I2C_CON_XA (1 << 8) /* Expand address */ |
| #define I2C_CON_STP (1 << 1) /* Stop condition (master mode only) */ |
| #define I2C_CON_STT (1 << 0) /* Start condition (master mode only) */ |
| |
| /* I2C System Test Register (I2C_SYSTEST): */ |
| |
| #define I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */ |
| #define I2C_SYSTEST_FREE (1 << 14) /* Free running mode, on brkpoint) */ |
| #define I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */ |
| #define I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */ |
| #define I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense input value */ |
| #define I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive output value */ |
| #define I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense input value */ |
| #define I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive output value */ |
| |
| /* I2C System Status Register (I2C_SYSS): */ |
| |
| #define I2C_SYSS_RDONE (1 << 0) /* Internel reset monitoring */ |
| |
| #define I2C_SCLL_SCLL 0 |
| #define I2C_SCLL_SCLL_M 0xFF |
| #define I2C_SCLL_HSSCLL 8 |
| #define I2C_SCLH_HSSCLL_M 0xFF |
| #define I2C_SCLH_SCLH 0 |
| #define I2C_SCLH_SCLH_M 0xFF |
| #define I2C_SCLH_HSSCLH 8 |
| #define I2C_SCLH_HSSCLH_M 0xFF |
| |
| #define OMAP_I2C_STANDARD 100000 |
| #define OMAP_I2C_FAST_MODE 400000 |
| #define OMAP_I2C_HIGH_SPEED 3400000 |
| |
| #define SYSTEM_CLOCK_12 12000000 |
| #define SYSTEM_CLOCK_13 13000000 |
| #define SYSTEM_CLOCK_192 19200000 |
| #define SYSTEM_CLOCK_96 96000000 |
| |
| /* Use the reference value of 96MHz if not explicitly set by the board */ |
| #ifndef I2C_IP_CLK |
| #define I2C_IP_CLK SYSTEM_CLOCK_96 |
| #endif |
| |
| /* |
| * The reference minimum clock for high speed is 19.2MHz. |
| * The linux 2.6.30 kernel uses this value. |
| * The reference minimum clock for fast mode is 9.6MHz |
| * The reference minimum clock for standard mode is 4MHz |
| * In TRM, the value of 12MHz is used. |
| */ |
| #ifndef I2C_INTERNAL_SAMPLING_CLK |
| #define I2C_INTERNAL_SAMPLING_CLK 19200000 |
| #endif |
| |
| /* |
| * The equation for the low and high time is |
| * tlow = scll + scll_trim = (sampling clock * tlow_duty) / speed |
| * thigh = sclh + sclh_trim = (sampling clock * (1 - tlow_duty)) / speed |
| * |
| * If the duty cycle is 50% |
| * |
| * tlow = scll + scll_trim = sampling clock / (2 * speed) |
| * thigh = sclh + sclh_trim = sampling clock / (2 * speed) |
| * |
| * In TRM |
| * scll_trim = 7 |
| * sclh_trim = 5 |
| * |
| * The linux 2.6.30 kernel uses |
| * scll_trim = 6 |
| * sclh_trim = 6 |
| * |
| * These are the trim values for standard and fast speed |
| */ |
| #ifndef I2C_FASTSPEED_SCLL_TRIM |
| #define I2C_FASTSPEED_SCLL_TRIM 6 |
| #endif |
| #ifndef I2C_FASTSPEED_SCLH_TRIM |
| #define I2C_FASTSPEED_SCLH_TRIM 6 |
| #endif |
| |
| /* These are the trim values for high speed */ |
| #ifndef I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM |
| #define I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM |
| #endif |
| #ifndef I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM |
| #define I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM I2C_FASTSPEED_SCLH_TRIM |
| #endif |
| #ifndef I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM |
| #define I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM |
| #endif |
| #ifndef I2C_HIGHSPEED_PHASE_TWO_SCLH_TRIM |
| #define I2C_HIGHSPEED_PHASE_TWO_SCLH_TRIM I2C_FASTSPEED_SCLH_TRIM |
| #endif |
| |
| #define I2C_PSC_MAX 0x0f |
| #define I2C_PSC_MIN 0x00 |
| |
| #endif /* _OMAP24XX_I2C_H_ */ |
