| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * (C) Copyright 2004, Psyent Corporation <www.psyent.com> |
| * Scott McNutt <smcnutt@psyent.com> |
| */ |
| |
| #include <asm-offsets.h> |
| #include <config.h> |
| #include <version.h> |
| |
| /* |
| * icache and dcache configuration used only for start.S. |
| * the values are chosen so that it will work for all configuration. |
| */ |
| #define ICACHE_LINE_SIZE 32 /* fixed 32 */ |
| #define ICACHE_SIZE_MAX 0x10000 /* 64k max */ |
| #define DCACHE_LINE_SIZE_MIN 4 /* 4, 16, 32 */ |
| #define DCACHE_SIZE_MAX 0x10000 /* 64k max */ |
| |
| /* RESTART */ |
| .text |
| .global _start, _except_start, _except_end |
| |
| _start: |
| wrctl status, r0 /* Disable interrupts */ |
| /* |
| * ICACHE INIT -- only the icache line at the reset address |
| * is invalidated at reset. So the init must stay within |
| * the cache line size (8 words). If GERMS is used, we'll |
| * just be invalidating the cache a second time. If cache |
| * is not implemented initi behaves as nop. |
| */ |
| ori r4, r0, %lo(ICACHE_LINE_SIZE) |
| movhi r5, %hi(ICACHE_SIZE_MAX) |
| ori r5, r5, %lo(ICACHE_SIZE_MAX) |
| 0: initi r5 |
| sub r5, r5, r4 |
| bgt r5, r0, 0b |
| br _except_end /* Skip the tramp */ |
| |
| /* |
| * EXCEPTION TRAMPOLINE -- the following gets copied |
| * to the exception address (below), but is otherwise at the |
| * default exception vector offset (0x0020). |
| */ |
| _except_start: |
| movhi et, %hi(_exception) |
| ori et, et, %lo(_exception) |
| jmp et |
| _except_end: |
| |
| /* |
| * INTERRUPTS -- for now, all interrupts masked and globally |
| * disabled. |
| */ |
| wrctl ienable, r0 /* All disabled */ |
| |
| /* |
| * DCACHE INIT -- if dcache not implemented, initd behaves as |
| * nop. |
| */ |
| ori r4, r0, %lo(DCACHE_LINE_SIZE_MIN) |
| movhi r5, %hi(DCACHE_SIZE_MAX) |
| ori r5, r5, %lo(DCACHE_SIZE_MAX) |
| mov r6, r0 |
| 1: initd 0(r6) |
| add r6, r6, r4 |
| bltu r6, r5, 1b |
| |
| /* |
| * RELOCATE CODE, DATA & COMMAND TABLE -- the following code |
| * assumes code, data and the command table are all |
| * contiguous. This lets us relocate everything as a single |
| * block. Make sure the linker script matches this ;-) |
| */ |
| nextpc r4 |
| _cur: movhi r5, %hi(_cur - _start) |
| ori r5, r5, %lo(_cur - _start) |
| sub r4, r4, r5 /* r4 <- cur _start */ |
| mov r8, r4 |
| movhi r5, %hi(_start) |
| ori r5, r5, %lo(_start) /* r5 <- linked _start */ |
| mov sp, r5 /* initial stack below u-boot code */ |
| beq r4, r5, 3f |
| |
| movhi r6, %hi(CONFIG_SYS_MONITOR_LEN) |
| ori r6, r6, %lo(CONFIG_SYS_MONITOR_LEN) |
| add r6, r6, r5 |
| 2: ldwio r7, 0(r4) |
| addi r4, r4, 4 |
| stwio r7, 0(r5) |
| addi r5, r5, 4 |
| bne r5, r6, 2b |
| 3: |
| |
| /* JUMP TO RELOC ADDR */ |
| movhi r4, %hi(_reloc) |
| ori r4, r4, %lo(_reloc) |
| jmp r4 |
| _reloc: |
| |
| /* STACK INIT -- zero top two words for call back chain. */ |
| addi sp, sp, -8 |
| stw r0, 0(sp) |
| stw r0, 4(sp) |
| mov fp, sp |
| |
| #ifdef CONFIG_DEBUG_UART |
| /* Set up the debug UART */ |
| movhi r2, %hi(debug_uart_init@h) |
| ori r2, r2, %lo(debug_uart_init@h) |
| callr r2 |
| #endif |
| |
| /* Allocate and initialize reserved area, update SP */ |
| mov r4, sp |
| movhi r2, %hi(board_init_f_alloc_reserve@h) |
| ori r2, r2, %lo(board_init_f_alloc_reserve@h) |
| callr r2 |
| mov sp, r2 |
| mov r4, sp |
| movhi r2, %hi(board_init_f_init_reserve@h) |
| ori r2, r2, %lo(board_init_f_init_reserve@h) |
| callr r2 |
| |
| /* Update frame-pointer */ |
| mov fp, sp |
| |
| /* Call board_init_f -- never returns */ |
| mov r4, r0 |
| movhi r2, %hi(board_init_f@h) |
| ori r2, r2, %lo(board_init_f@h) |
| callr r2 |
| |
| /* |
| * NEVER RETURNS -- but branch to the _start just |
| * in case ;-) |
| */ |
| br _start |
| |
| /* |
| * relocate_code -- Nios2 handles the relocation above. But |
| * the generic board code monkeys with the heap, stack, etc. |
| * (it makes some assumptions that may not be appropriate |
| * for Nios). Nevertheless, we capitulate here. |
| * |
| * We'll call the board_init_r from here since this isn't |
| * supposed to return. |
| * |
| * void relocate_code (ulong sp, gd_t *global_data, |
| * ulong reloc_addr) |
| * __attribute__ ((noreturn)); |
| */ |
| .text |
| .global relocate_code |
| |
| relocate_code: |
| mov sp, r4 /* Set the new sp */ |
| mov r4, r5 |
| |
| /* |
| * ZERO BSS/SBSS -- bss and sbss are assumed to be adjacent |
| * and between __bss_start and __bss_end. |
| */ |
| movhi r5, %hi(__bss_start) |
| ori r5, r5, %lo(__bss_start) |
| movhi r6, %hi(__bss_end) |
| ori r6, r6, %lo(__bss_end) |
| beq r5, r6, 5f |
| |
| 4: stw r0, 0(r5) |
| addi r5, r5, 4 |
| bne r5, r6, 4b |
| 5: |
| |
| movhi r8, %hi(board_init_r@h) |
| ori r8, r8, %lo(board_init_r@h) |
| callr r8 |
| ret |
