/*
 * Copyright 2018 NXP
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __IMX8MM_VAL_H
#define __IMX8MM_VAL_H

#include <linux/sizes.h>
#include <asm/arch/imx-regs.h>

#ifdef CONFIG_SECURE_BOOT
#define CONFIG_CSF_SIZE			0x2000 /* 8K region */
#endif

#define CONFIG_SPL_MAX_SIZE		(148 * 1024)
#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
#define CONFIG_SYS_UBOOT_BASE		(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)

#ifdef CONFIG_SPL_BUILD
/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
#define CONFIG_SPL_WATCHDOG_SUPPORT
#define CONFIG_SPL_POWER_SUPPORT
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_STACK		0x91FFF0
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_BSS_START_ADDR      0x00910000
#define CONFIG_SPL_BSS_MAX_SIZE        0x1000	/* 4 KB */
#define CONFIG_SYS_SPL_MALLOC_START    0x00911000
#define CONFIG_SYS_SPL_MALLOC_SIZE     0x3000	/* 12 KB */
#define CONFIG_SYS_ICACHE_OFF
#define CONFIG_SYS_DCACHE_OFF

#define CONFIG_SPL_ABORT_ON_RAW_IMAGE /* For RAW image gives a error info not panic */

#undef CONFIG_DM_MMC
#undef CONFIG_DM_PMIC
#undef CONFIG_DM_PMIC_PFUZE100

#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_BD71837

#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */

#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
#endif

#define CONFIG_REMAKE_ELF

#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_LATE_INIT

#undef CONFIG_CMD_EXPORTENV
#undef CONFIG_CMD_IMPORTENV
#undef CONFIG_CMD_IMLS

#undef CONFIG_CMD_CRC32
#undef CONFIG_BOOTM_NETBSD

/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
#define CONFIG_MII
#define CONFIG_ETHPRIME                 "FEC"

#define CONFIG_FEC_MXC
#define FEC_QUIRK_ENET_MAC

#define IMX_FEC_BASE			0x30BE0000
#define CONFIG_PHYLIB

#ifdef CONFIG_TARGET_IMX8MM_DDR3L_VAL
#define CONFIG_FEC_XCV_TYPE             RMII
#define CONFIG_PHY_REALTEK
#define CONFIG_FEC_MXC_PHYADDR          3
#else
#define CONFIG_FEC_MXC_PHYADDR          0
#define CONFIG_FEC_XCV_TYPE             RGMII
#define CONFIG_PHY_ATHEROS
#define CONFIG_PHY_GIGE
#endif

#endif

#define CONFIG_MFG_ENV_SETTINGS \
	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
		"rdinit=/linuxrc " \
		"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
		"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
		"g_mass_storage.iSerialNumber=\"\" "\
		"clk_ignore_unused "\
		"\0" \
	"initrd_addr=0x43800000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"bootcmd_mfg=run mfgtool_args;booti ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS		\
	CONFIG_MFG_ENV_SETTINGS \
	"script=boot.scr\0" \
	"image=Image\0" \
	"console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200\0" \
	"fdt_addr=0x43000000\0"			\
	"fdt_high=0xffffffffffffffff\0"		\
	"boot_fdt=try\0" \
	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
	"initrd_addr=0x43800000\0"		\
	"initrd_high=0xffffffffffffffff\0" \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
	"mmcautodetect=yes\0" \
	"mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
		"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
		"run mmcargs; " \
		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
			"if run loadfdt; then " \
				"booti ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"echo WARN: Cannot load the DT; " \
			"fi; " \
		"else " \
			"echo wait for boot; " \
		"fi;\0" \
	"netargs=setenv bootargs console=${console} " \
		"root=/dev/nfs " \
		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
	"netboot=echo Booting from net ...; " \
		"run netargs;  " \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"${get_cmd} ${loadaddr} ${image}; " \
		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
				"booti ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"echo WARN: Cannot load the DT; " \
			"fi; " \
		"else " \
			"booti; " \
		"fi;\0"

#define CONFIG_BOOTCOMMAND \
	   "mmc dev ${mmcdev}; if mmc rescan; then " \
		   "if run loadbootscript; then " \
			   "run bootscript; " \
		   "else " \
			   "if run loadimage; then " \
				   "run mmcboot; " \
			   "else run netboot; " \
			   "fi; " \
		   "fi; " \
	   "else booti ${loadaddr} - ${fdt_addr}; fi"

/* Link Definitions */
#define CONFIG_LOADADDR			0x40480000

#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR

#define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE        0x80000
#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

#define CONFIG_ENV_OVERWRITE
#if defined(CONFIG_ENV_IS_IN_MMC)
#define CONFIG_ENV_OFFSET               (64 * SZ_64K)
#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
#define CONFIG_ENV_OFFSET		(4 * 1024 * 1024)
#define CONFIG_ENV_SECT_SIZE		(64 * 1024)
#define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
#endif
#define CONFIG_ENV_SIZE			0x1000
#define CONFIG_SYS_MMC_ENV_DEV		1   /* USDHC2 */
#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (2*1024) + (16*1024)) * 1024)

#define CONFIG_SYS_SDRAM_BASE           0x40000000
#define PHYS_SDRAM                      0x40000000
#define PHYS_SDRAM_SIZE			0x80000000 /* 2GB DDR */

#define CONFIG_SYS_MEMTEST_START    PHYS_SDRAM
#define CONFIG_SYS_MEMTEST_END      (CONFIG_SYS_MEMTEST_START + (PHYS_SDRAM_SIZE >> 1))

#define CONFIG_BAUDRATE			115200

#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE		UART2_BASE_ADDR

/* Monitor Command Prompt */
#undef CONFIG_SYS_PROMPT
#define CONFIG_SYS_PROMPT		"u-boot=> "
#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
#define CONFIG_SYS_CBSIZE              2048
#define CONFIG_SYS_MAXARGS             64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
					sizeof(CONFIG_SYS_PROMPT) + 16)

#define CONFIG_IMX_BOOTAUX

/* USDHC */
#define CONFIG_CMD_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_FSL_USDHC

#ifdef CONFIG_TARGET_IMX8MM_DDR3L_VAL
#define CONFIG_SYS_FSL_USDHC_NUM	1
#else
#define CONFIG_SYS_FSL_USDHC_NUM	2
#endif
#define CONFIG_SYS_FSL_ESDHC_ADDR       0

#define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
#define CONFIG_SYS_MMC_IMG_LOAD_PART	1

#ifdef CONFIG_FSL_FSPI
#define FSL_FSPI_FLASH_SIZE		SZ_32M
#define FSL_FSPI_FLASH_NUM		1
#define FSPI0_BASE_ADDR			0x30bb0000
#define FSPI0_AMBA_BASE			0x0
#define CONFIG_FSPI_QUAD_SUPPORT

#define CONFIG_SYS_FSL_FSPI_AHB
#endif

#ifdef CONFIG_NAND_MXS
#define CONFIG_CMD_NAND_TRIMFFS

/* NAND stuff */
#define CONFIG_SYS_MAX_NAND_DEVICE     1
#define CONFIG_SYS_NAND_BASE           0x20000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_ONFI_DETECTION

#ifdef CONFIG_CMD_UBI
#define CONFIG_MTD_DEVICE
#endif
#endif /* CONFIG_NAND_MXS */


#define CONFIG_MXC_GPIO

#define CONFIG_MXC_OCOTP
#define CONFIG_CMD_FUSE

#ifndef CONFIG_DM_I2C
#define CONFIG_SYS_I2C
#endif
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED		100000

/* USB configs */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
#define CONFIG_USBD_HS

#define CONFIG_CMD_USB_MASS_STORAGE
#define CONFIG_USB_GADGET_MASS_STORAGE
#define CONFIG_USB_GADGET_DOWNLOAD
#define CONFIG_USB_FUNCTION_MASS_STORAGE

#endif

#define CONFIG_USB_GADGET_DUALSPEED
#define CONFIG_USB_GADGET_VBUS_DRAW 2

#define CONFIG_CI_UDC

#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_USB_MAX_CONTROLLER_COUNT         2


#define CONFIG_OF_SYSTEM_SETUP

#endif