diff --git a/board/altera/ep1c20/ep1c20.c b/board/altera/ep1c20/ep1c20.c
index c5bfb85..82900f7 100644
--- a/board/altera/ep1c20/ep1c20.c
+++ b/board/altera/ep1c20/ep1c20.c
@@ -22,6 +22,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 int board_early_init_f (void)
 {
@@ -38,3 +39,14 @@
 {
 	return (0);
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/altera/ep1s10/ep1s10.c b/board/altera/ep1s10/ep1s10.c
index de9bf42..cf886da 100644
--- a/board/altera/ep1s10/ep1s10.c
+++ b/board/altera/ep1s10/ep1s10.c
@@ -22,6 +22,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 int board_early_init_f (void)
 {
@@ -38,3 +39,14 @@
 {
 	return (0);
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/altera/ep1s40/ep1s40.c b/board/altera/ep1s40/ep1s40.c
index c0eca17..6395de7 100644
--- a/board/altera/ep1s40/ep1s40.c
+++ b/board/altera/ep1s40/ep1s40.c
@@ -22,6 +22,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 int checkboard (void)
 {
@@ -33,3 +34,14 @@
 {
 	return (0);
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/armltd/integrator/integrator.c b/board/armltd/integrator/integrator.c
index a46deea..518944e 100644
--- a/board/armltd/integrator/integrator.c
+++ b/board/armltd/integrator/integrator.c
@@ -34,9 +34,7 @@
  */
 
 #include <common.h>
-#ifdef CONFIG_PCI
 #include <netdev.h>
-#endif
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -127,9 +125,16 @@
 	return 0;
 }
 
-#ifdef CONFIG_PCI
+#ifdef CONFIG_CMD_NET
 int board_eth_init(bd_t *bis)
 {
-	return pci_eth_init(bis);
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+#ifdef CONFIG_PCI
+	rc += pci_eth_init(bis);
+#endif
+	return rc;
 }
 #endif
diff --git a/board/armltd/versatile/versatile.c b/board/armltd/versatile/versatile.c
index 197bc89..6e836dd 100644
--- a/board/armltd/versatile/versatile.c
+++ b/board/armltd/versatile/versatile.c
@@ -34,6 +34,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -89,3 +90,14 @@
 {
 	return 0;
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/bf533-ezkit/bf533-ezkit.c b/board/bf533-ezkit/bf533-ezkit.c
index d5f0b7c..8727dee 100644
--- a/board/bf533-ezkit/bf533-ezkit.c
+++ b/board/bf533-ezkit/bf533-ezkit.c
@@ -26,6 +26,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include "psd4256.h"
 #include "flash-defines.h"
 
@@ -57,3 +58,10 @@
 
 	return 0;
 }
+
+#ifdef CONFIG_SMC91111
+int board_eth_init(bd_t *bis)
+{
+	return smc91111_initialize(0, CONFIG_SMC91111_BASE);
+}
+#endif
diff --git a/board/bf533-stamp/bf533-stamp.c b/board/bf533-stamp/bf533-stamp.c
index 7108dda..a226910 100644
--- a/board/bf533-stamp/bf533-stamp.c
+++ b/board/bf533-stamp/bf533-stamp.c
@@ -26,6 +26,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <asm/io.h>
 #include "bf533-stamp.h"
 
@@ -283,3 +284,10 @@
 }
 
 #endif
+
+#ifdef CONFIG_SMC91111
+int board_eth_init(bd_t *bis)
+{
+	return smc91111_initialize(0, CONFIG_SMC91111_BASE);
+}
+#endif
diff --git a/board/bf538f-ezkit/bf538f-ezkit.c b/board/bf538f-ezkit/bf538f-ezkit.c
index bbee989..15916fa 100644
--- a/board/bf538f-ezkit/bf538f-ezkit.c
+++ b/board/bf538f-ezkit/bf538f-ezkit.c
@@ -7,6 +7,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <config.h>
 #include <asm/blackfin.h>
 
@@ -25,3 +26,10 @@
 	gd->bd->bi_memsize = CONFIG_SYS_MAX_RAM_SIZE;
 	return gd->bd->bi_memsize;
 }
+
+#ifdef CONFIG_SMC91111
+int board_eth_init(bd_t *bis)
+{
+	return smc91111_initialize(0, CONFIG_SMC91111_BASE);
+}
+#endif
diff --git a/board/bf561-ezkit/bf561-ezkit.c b/board/bf561-ezkit/bf561-ezkit.c
index 5aede17..e5d7eb3 100644
--- a/board/bf561-ezkit/bf561-ezkit.c
+++ b/board/bf561-ezkit/bf561-ezkit.c
@@ -26,6 +26,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <asm/io.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -43,3 +44,10 @@
 	gd->bd->bi_memsize = CONFIG_SYS_MAX_RAM_SIZE;
 	return gd->bd->bi_memsize;
 }
+
+#ifdef CONFIG_SMC91111
+int board_eth_init(bd_t *bis)
+{
+	return smc91111_initialize(0, CONFIG_SMC91111_BASE);
+}
+#endif
diff --git a/board/blackstamp/blackstamp.c b/board/blackstamp/blackstamp.c
index b671899..f55ab97 100644
--- a/board/blackstamp/blackstamp.c
+++ b/board/blackstamp/blackstamp.c
@@ -12,6 +12,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <asm/io.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -44,3 +45,10 @@
 	SSYNC();
 }
 #endif
+
+#ifdef CONFIG_SMC91111
+int board_eth_init(bd_t *bis)
+{
+	return smc91111_initialize(0, CONFIG_SMC91111_BASE);
+}
+#endif
diff --git a/board/cerf250/cerf250.c b/board/cerf250/cerf250.c
index 307894f..59346bc 100644
--- a/board/cerf250/cerf250.c
+++ b/board/cerf250/cerf250.c
@@ -26,6 +26,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -71,3 +72,14 @@
 
 	return 0;
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/cm-bf533/cm-bf533.c b/board/cm-bf533/cm-bf533.c
index 7eb761d..ab0bf3b 100644
--- a/board/cm-bf533/cm-bf533.c
+++ b/board/cm-bf533/cm-bf533.c
@@ -7,6 +7,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -23,3 +24,10 @@
 	gd->bd->bi_memsize = CONFIG_SYS_MAX_RAM_SIZE;
 	return gd->bd->bi_memsize;
 }
+
+#ifdef CONFIG_SMC91111
+int board_eth_init(bd_t *bis)
+{
+	return smc91111_initialize(0, CONFIG_SMC91111_BASE);
+}
+#endif
diff --git a/board/cm-bf561/cm-bf561.c b/board/cm-bf561/cm-bf561.c
index 5bce9eb..f21a015 100644
--- a/board/cm-bf561/cm-bf561.c
+++ b/board/cm-bf561/cm-bf561.c
@@ -7,6 +7,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -23,3 +24,10 @@
 	gd->bd->bi_memsize = CONFIG_SYS_MAX_RAM_SIZE;
 	return gd->bd->bi_memsize;
 }
+
+#ifdef CONFIG_SMC91111
+int board_eth_init(bd_t *bis)
+{
+	return smc91111_initialize(0, CONFIG_SMC91111_BASE);
+}
+#endif
diff --git a/board/cradle/cradle.c b/board/cradle/cradle.c
index 6d8d555..21eb655 100644
--- a/board/cradle/cradle.c
+++ b/board/cradle/cradle.c
@@ -27,6 +27,7 @@
 
 #include <asm/arch/pxa-regs.h>
 #include <common.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -223,3 +224,14 @@
 		PHYS_SDRAM_3_SIZE +
 		PHYS_SDRAM_4_SIZE );
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/delta/delta.c b/board/delta/delta.c
index 84ff47e..a294213 100644
--- a/board/delta/delta.c
+++ b/board/delta/delta.c
@@ -22,6 +22,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <i2c.h>
 #include <da9030.h>
 #include <malloc.h>
@@ -363,3 +364,14 @@
 	i2c_reg_write(addr, SYS_CONTROL_A, val);
 }
 #endif
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/dnp1110/dnp1110.c b/board/dnp1110/dnp1110.c
index ab8e7be..c215f5f 100644
--- a/board/dnp1110/dnp1110.c
+++ b/board/dnp1110/dnp1110.c
@@ -23,6 +23,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <SA-1100.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -53,3 +54,14 @@
 
 	return (0);
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/gaisler/gr_cpci_ax2000/gr_cpci_ax2000.c b/board/gaisler/gr_cpci_ax2000/gr_cpci_ax2000.c
index 105a747..7fe85b8 100644
--- a/board/gaisler/gr_cpci_ax2000/gr_cpci_ax2000.c
+++ b/board/gaisler/gr_cpci_ax2000/gr_cpci_ax2000.c
@@ -19,6 +19,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <config.h>
 #include <asm/leon.h>
 
@@ -37,3 +38,14 @@
 {
 	return 0;
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/gaisler/gr_ep2s60/gr_ep2s60.c b/board/gaisler/gr_ep2s60/gr_ep2s60.c
index 2904d32..7241c6d 100644
--- a/board/gaisler/gr_ep2s60/gr_ep2s60.c
+++ b/board/gaisler/gr_ep2s60/gr_ep2s60.c
@@ -19,6 +19,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <config.h>
 #include <asm/leon.h>
 
@@ -37,3 +38,14 @@
 {
 	return 0;
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/innokom/innokom.c b/board/innokom/innokom.c
index c2b88ae..3412f10 100644
--- a/board/innokom/innokom.c
+++ b/board/innokom/innokom.c
@@ -24,6 +24,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <asm/arch/pxa-regs.h>
 #include <asm/mach-types.h>
 
@@ -182,3 +183,14 @@
 
 	return;
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/logodl/logodl.c b/board/logodl/logodl.c
index c57210a..2562ecc 100644
--- a/board/logodl/logodl.c
+++ b/board/logodl/logodl.c
@@ -23,6 +23,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <asm/arch/pxa-regs.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -120,3 +121,14 @@
 
 	return;
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/lpd7a40x/lpd7a40x.c b/board/lpd7a40x/lpd7a40x.c
index 7edb65e..437dad0 100644
--- a/board/lpd7a40x/lpd7a40x.c
+++ b/board/lpd7a40x/lpd7a40x.c
@@ -26,6 +26,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #if defined(CONFIG_LH7A400)
 #include <lh7a400.h>
 #elif defined(CONFIG_LH7A404)
@@ -79,3 +80,14 @@
 
 	return 0;
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/ms7722se/ms7722se.c b/board/ms7722se/ms7722se.c
index 32234d3..4e40b17 100644
--- a/board/ms7722se/ms7722se.c
+++ b/board/ms7722se/ms7722se.c
@@ -24,6 +24,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <asm/io.h>
 #include <asm/processor.h>
 
@@ -57,3 +58,14 @@
 {
 	writew(value & 0xFF, LED_BASE);
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/netstar/eeprom.c b/board/netstar/eeprom.c
index 5806128..1366457 100644
--- a/board/netstar/eeprom.c
+++ b/board/netstar/eeprom.c
@@ -27,43 +27,42 @@
 #include <common.h>
 #include <exports.h>
 #include <timestamp.h>
+#include <net.h>
 #include "../drivers/net/smc91111.h"
 
-#define SMC_BASE_ADDRESS CONFIG_SMC91111_BASE
-
-static u16 read_eeprom_reg(u16 reg)
+static u16 read_eeprom_reg(struct eth_device *dev, u16 reg)
 {
 	int timeout;
 
-	SMC_SELECT_BANK(2);
-	SMC_outw(reg, PTR_REG);
+	SMC_SELECT_BANK(dev, 2);
+	SMC_outw(dev, reg, PTR_REG);
 
-	SMC_SELECT_BANK(1);
-	SMC_outw(SMC_inw (CTL_REG) | CTL_EEPROM_SELECT | CTL_RELOAD,
+	SMC_SELECT_BANK(dev, 1);
+	SMC_outw(dev, SMC_inw (dev, CTL_REG) | CTL_EEPROM_SELECT | CTL_RELOAD,
 		 CTL_REG);
 	timeout = 100;
-	while((SMC_inw (CTL_REG) & CTL_RELOAD) && --timeout)
+	while((SMC_inw (dev, CTL_REG) & CTL_RELOAD) && --timeout)
 		udelay(100);
 	if (timeout == 0) {
 		printf("Timeout Reading EEPROM register %02x\n", reg);
 		return 0;
 	}
 
-	return SMC_inw (GP_REG);
+	return SMC_inw (dev, GP_REG);
 }
 
-static int write_eeprom_reg(u16 value, u16 reg)
+static int write_eeprom_reg(struct eth_device *dev, u16 value, u16 reg)
 {
 	int timeout;
 
-	SMC_SELECT_BANK(2);
-	SMC_outw(reg, PTR_REG);
+	SMC_SELECT_BANK(dev, 2);
+	SMC_outw(dev, reg, PTR_REG);
 
-	SMC_SELECT_BANK(1);
-	SMC_outw(value, GP_REG);
-	SMC_outw(SMC_inw (CTL_REG) | CTL_EEPROM_SELECT | CTL_STORE, CTL_REG);
+	SMC_SELECT_BANK(dev, 1);
+	SMC_outw(dev, value, GP_REG);
+	SMC_outw(dev, SMC_inw (dev, CTL_REG) | CTL_EEPROM_SELECT | CTL_STORE, CTL_REG);
 	timeout = 100;
-	while ((SMC_inw(CTL_REG) & CTL_STORE) && --timeout)
+	while ((SMC_inw(dev, CTL_REG) & CTL_STORE) && --timeout)
 		udelay (100);
 	if (timeout == 0) {
 		printf("Timeout Writing EEPROM register %02x\n", reg);
@@ -73,17 +72,17 @@
 	return 1;
 }
 
-static int write_data(u16 *buf, int len)
+static int write_data(struct eth_device *dev, u16 *buf, int len)
 {
 	u16 reg = 0x23;
 
 	while (len--)
-		write_eeprom_reg(*buf++, reg++);
+		write_eeprom_reg(dev, *buf++, reg++);
 
 	return 0;
 }
 
-static int verify_macaddr(char *s)
+static int verify_macaddr(struct eth_device *dev, char *s)
 {
 	u16 reg;
 	int i, err = 0;
@@ -91,7 +90,7 @@
 	printf("MAC Address: ");
 	err = i = 0;
 	for (i = 0; i < 3; i++) {
-		reg = read_eeprom_reg(0x20 + i);
+		reg = read_eeprom_reg(dev, 0x20 + i);
 		printf("%02x:%02x%c", reg & 0xff, reg >> 8, i != 2 ? ':' : '\n');
 		if (s)
 			err |= reg != ((u16 *)s)[i];
@@ -100,7 +99,7 @@
 	return err ? 0 : 1;
 }
 
-static int set_mac(char *s)
+static int set_mac(struct eth_device *dev, char *s)
 {
 	int i;
 	char *e, eaddr[6];
@@ -112,7 +111,7 @@
 	}
 
 	for (i = 0; i < 3; i++)
-		write_eeprom_reg(*(((u16 *)eaddr) + i), 0x20 + i);
+		write_eeprom_reg(dev, *(((u16 *)eaddr) + i), 0x20 + i);
 
 	return 0;
 }
@@ -150,6 +149,10 @@
 	int i, len, ret;
 	unsigned char buf[58], *p;
 
+	struct eth_device dev = {
+		.iobase = CONFIG_SMC91111_BASE
+	};
+
 	app_startup(argv);
 	if (get_version() != XF_VERSION) {
 		printf("Wrong XF_VERSION.\n");
@@ -160,14 +163,14 @@
 
 	return crcek();
 
-	if ((SMC_inw (BANK_SELECT) & 0xFF00) != 0x3300) {
+	if ((SMC_inw (&dev, BANK_SELECT) & 0xFF00) != 0x3300) {
 		printf("SMSC91111 not found.\n");
 		return 2;
 	}
 
 	/* Called without parameters - print MAC address */
 	if (argc < 2) {
-		verify_macaddr(NULL);
+		verify_macaddr(&dev, NULL);
 		return 0;
 	}
 
@@ -201,8 +204,8 @@
 	}
 
 	/* First argument (MAC) is mandatory */
-	set_mac(argv[1]);
-	if (verify_macaddr(argv[1])) {
+	set_mac(&dev, argv[1]);
+	if (verify_macaddr(&dev, argv[1])) {
 		printf("*** MAC address does not match! ***\n");
 		return 4;
 	}
@@ -210,7 +213,7 @@
 	while (len--)
 		*p++ = 0;
 
-	write_data((u16 *)buf, sizeof(buf) >> 1);
+	write_data(&dev, (u16 *)buf, sizeof(buf) >> 1);
 
 	return 0;
 }
diff --git a/board/netstar/netstar.c b/board/netstar/netstar.c
index ffd60bf..df1704b 100644
--- a/board/netstar/netstar.c
+++ b/board/netstar/netstar.c
@@ -21,6 +21,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <i2c.h>
 #include <flash.h>
 #include <nand.h>
@@ -115,3 +116,14 @@
 	return 0;
 }
 #endif
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/psyent/pk1c20/pk1c20.c b/board/psyent/pk1c20/pk1c20.c
index 95b48bc..0a24866 100644
--- a/board/psyent/pk1c20/pk1c20.c
+++ b/board/psyent/pk1c20/pk1c20.c
@@ -22,6 +22,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 int board_early_init_f (void)
 {
@@ -38,3 +39,14 @@
 {
 	return (0);
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/pxa255_idp/pxa_idp.c b/board/pxa255_idp/pxa_idp.c
index e9e479c..05e30ec 100644
--- a/board/pxa255_idp/pxa_idp.c
+++ b/board/pxa255_idp/pxa_idp.c
@@ -31,6 +31,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <command.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -133,3 +134,14 @@
 );
 
 #endif
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/renesas/MigoR/migo_r.c b/board/renesas/MigoR/migo_r.c
index 204ca78..c0f26ac 100644
--- a/board/renesas/MigoR/migo_r.c
+++ b/board/renesas/MigoR/migo_r.c
@@ -24,6 +24,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <asm/io.h>
 #include <asm/processor.h>
 
@@ -51,3 +52,14 @@
 void led_set_state (unsigned short value)
 {
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/st/nhk8815/nhk8815.c b/board/st/nhk8815/nhk8815.c
index 1fa506a..faef810 100644
--- a/board/st/nhk8815/nhk8815.c
+++ b/board/st/nhk8815/nhk8815.c
@@ -26,6 +26,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <asm/io.h>
 #include <asm/arch/gpio.h>
 
@@ -89,3 +90,14 @@
 	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
 	return 0;
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/voiceblue/eeprom.c b/board/voiceblue/eeprom.c
index f01597a..2ae46d1 100644
--- a/board/voiceblue/eeprom.c
+++ b/board/voiceblue/eeprom.c
@@ -27,43 +27,42 @@
 #include <common.h>
 #include <exports.h>
 #include <timestamp.h>
+#include <net.h>
 #include "../drivers/net/smc91111.h"
 
-#define SMC_BASE_ADDRESS CONFIG_SMC91111_BASE
-
-static u16 read_eeprom_reg(u16 reg)
+static u16 read_eeprom_reg(struct eth_device *dev, u16 reg)
 {
 	int timeout;
 
-	SMC_SELECT_BANK(2);
-	SMC_outw(reg, PTR_REG);
+	SMC_SELECT_BANK(dev, 2);
+	SMC_outw(dev, reg, PTR_REG);
 
-	SMC_SELECT_BANK(1);
-	SMC_outw(SMC_inw (CTL_REG) | CTL_EEPROM_SELECT | CTL_RELOAD,
+	SMC_SELECT_BANK(dev, 1);
+	SMC_outw(dev, SMC_inw (dev, CTL_REG) | CTL_EEPROM_SELECT | CTL_RELOAD,
 		 CTL_REG);
 	timeout = 100;
-	while((SMC_inw (CTL_REG) & CTL_RELOAD) && --timeout)
+	while((SMC_inw (dev, CTL_REG) & CTL_RELOAD) && --timeout)
 		udelay(100);
 	if (timeout == 0) {
 		printf("Timeout Reading EEPROM register %02x\n", reg);
 		return 0;
 	}
 
-	return SMC_inw (GP_REG);
+	return SMC_inw (dev, GP_REG);
 }
 
-static int write_eeprom_reg(u16 value, u16 reg)
+static int write_eeprom_reg(struct eth_device *dev, u16 value, u16 reg)
 {
 	int timeout;
 
-	SMC_SELECT_BANK(2);
-	SMC_outw(reg, PTR_REG);
+	SMC_SELECT_BANK(dev, 2);
+	SMC_outw(dev, reg, PTR_REG);
 
-	SMC_SELECT_BANK(1);
-	SMC_outw(value, GP_REG);
-	SMC_outw(SMC_inw (CTL_REG) | CTL_EEPROM_SELECT | CTL_STORE, CTL_REG);
+	SMC_SELECT_BANK(dev, 1);
+	SMC_outw(dev, value, GP_REG);
+	SMC_outw(dev, SMC_inw (dev, CTL_REG) | CTL_EEPROM_SELECT | CTL_STORE, CTL_REG);
 	timeout = 100;
-	while ((SMC_inw(CTL_REG) & CTL_STORE) && --timeout)
+	while ((SMC_inw(dev, CTL_REG) & CTL_STORE) && --timeout)
 		udelay (100);
 	if (timeout == 0) {
 		printf("Timeout Writing EEPROM register %02x\n", reg);
@@ -73,17 +72,17 @@
 	return 1;
 }
 
-static int write_data(u16 *buf, int len)
+static int write_data(struct eth_device *dev, u16 *buf, int len)
 {
 	u16 reg = 0x23;
 
 	while (len--)
-		write_eeprom_reg(*buf++, reg++);
+		write_eeprom_reg(dev, *buf++, reg++);
 
 	return 0;
 }
 
-static int verify_macaddr(char *s)
+static int verify_macaddr(struct eth_device *dev, char *s)
 {
 	u16 reg;
 	int i, err = 0;
@@ -91,7 +90,7 @@
 	printf("MAC Address: ");
 	err = i = 0;
 	for (i = 0; i < 3; i++) {
-		reg = read_eeprom_reg(0x20 + i);
+		reg = read_eeprom_reg(dev, 0x20 + i);
 		printf("%02x:%02x%c", reg & 0xff, reg >> 8, i != 2 ? ':' : '\n');
 		if (s)
 			err |= reg != ((u16 *)s)[i];
@@ -100,7 +99,7 @@
 	return err ? 0 : 1;
 }
 
-static int set_mac(char *s)
+static int set_mac(struct eth_device *dev, char *s)
 {
 	int i;
 	char *e, eaddr[6];
@@ -112,7 +111,7 @@
 	}
 
 	for (i = 0; i < 3; i++)
-		write_eeprom_reg(*(((u16 *)eaddr) + i), 0x20 + i);
+		write_eeprom_reg(dev, *(((u16 *)eaddr) + i), 0x20 + i);
 
 	return 0;
 }
@@ -148,6 +147,10 @@
 	int i, len, ret;
 	unsigned char buf[58], *p;
 
+	struct eth_device dev = {
+		.iobase = CONFIG_SMC91111_BASE
+	};
+
 	app_startup(argv);
 	if (get_version() != XF_VERSION) {
 		printf("Wrong XF_VERSION.\n");
@@ -156,14 +159,14 @@
 		return 1;
 	}
 
-	if ((SMC_inw (BANK_SELECT) & 0xFF00) != 0x3300) {
+	if ((SMC_inw (&dev, BANK_SELECT) & 0xFF00) != 0x3300) {
 		printf("SMSC91111 not found.\n");
 		return 2;
 	}
 
 	/* Called without parameters - print MAC address */
 	if (argc < 2) {
-		verify_macaddr(NULL);
+		verify_macaddr(&dev, NULL);
 		return 0;
 	}
 
@@ -197,8 +200,8 @@
 	}
 
 	/* First argument (MAC) is mandatory */
-	set_mac(argv[1]);
-	if (verify_macaddr(argv[1])) {
+	set_mac(&dev, argv[1]);
+	if (verify_macaddr(&dev, argv[1])) {
 		printf("*** MAC address does not match! ***\n");
 		return 4;
 	}
@@ -206,7 +209,7 @@
 	while (len--)
 		*p++ = 0;
 
-	write_data((u16 *)buf, sizeof(buf) >> 1);
+	write_data(&dev, (u16 *)buf, sizeof(buf) >> 1);
 
 	return 0;
 }
diff --git a/board/voiceblue/voiceblue.c b/board/voiceblue/voiceblue.c
index 59b3310..5f8af2b 100644
--- a/board/voiceblue/voiceblue.c
+++ b/board/voiceblue/voiceblue.c
@@ -20,6 +20,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -66,3 +67,14 @@
 
 	return 0;
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/xaeniax/xaeniax.c b/board/xaeniax/xaeniax.c
index 9baa457..4c19c4d 100644
--- a/board/xaeniax/xaeniax.c
+++ b/board/xaeniax/xaeniax.c
@@ -29,6 +29,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -71,3 +72,14 @@
 
 	return 0;
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/xm250/xm250.c b/board/xm250/xm250.c
index 56b1cd4..246bdde 100644
--- a/board/xm250/xm250.c
+++ b/board/xm250/xm250.c
@@ -27,6 +27,7 @@
 
 #include <asm/arch/pxa-regs.h>
 #include <common.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -80,3 +81,14 @@
 
 	return (0);
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/xsengine/xsengine.c b/board/xsengine/xsengine.c
index 65923e9..4464fd4 100644
--- a/board/xsengine/xsengine.c
+++ b/board/xsengine/xsengine.c
@@ -26,6 +26,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -61,3 +62,14 @@
 
 	return 0;
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/board/zylonite/zylonite.c b/board/zylonite/zylonite.c
index 5829170..749a40f 100644
--- a/board/zylonite/zylonite.c
+++ b/board/zylonite/zylonite.c
@@ -26,6 +26,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -68,3 +69,14 @@
 
 	return 0;
 }
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC91111
+	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+	return rc;
+}
+#endif
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index be5c484..fc9887b 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -64,7 +64,7 @@
 COBJS-$(CONFIG_RTL8169) += rtl8169.o
 COBJS-$(CONFIG_DRIVER_S3C4510_ETH) += s3c4510b_eth.o
 COBJS-$(CONFIG_SH_ETHER) += sh_eth.o
-COBJS-$(CONFIG_DRIVER_SMC91111) += smc91111.o
+COBJS-$(CONFIG_SMC91111) += smc91111.o
 COBJS-$(CONFIG_SMC911X) += smc911x.o
 COBJS-$(CONFIG_TIGON3) += tigon3.o bcm570x_autoneg.o 5701rls.o
 COBJS-$(CONFIG_DRIVER_TI_EMAC) += davinci_emac.o
diff --git a/drivers/net/smc91111.c b/drivers/net/smc91111.c
index b41e4d2..54a1bfb 100644
--- a/drivers/net/smc91111.c
+++ b/drivers/net/smc91111.c
@@ -62,6 +62,7 @@
 #include <common.h>
 #include <command.h>
 #include <config.h>
+#include <malloc.h>
 #include "smc91111.h"
 #include <net.h>
 
@@ -122,17 +123,15 @@
  . what you are doing.
  .
  -------------------------------------------------------------------------*/
-#define CARDNAME "LAN91C111"
 
 /* Memory sizing constant */
 #define LAN91C111_MEMORY_MULTIPLIER	(1024*2)
 
 #ifndef CONFIG_SMC91111_BASE
-#define CONFIG_SMC91111_BASE 0x20000300
+#error "SMC91111 Base address must be passed to initialization funciton"
+/* #define CONFIG_SMC91111_BASE 0x20000300 */
 #endif
 
-#define SMC_BASE_ADDRESS CONFIG_SMC91111_BASE
-
 #define SMC_DEV_NAME "SMC91111"
 #define SMC_PHY_ADDR 0x0000
 #define SMC_ALLOC_MAX_TRY 5
@@ -147,73 +146,18 @@
 #else
 #undef USE_32_BIT
 #endif
-/*-----------------------------------------------------------------
- .
- .  The driver can be entered at any of the following entry points.
- .
- .------------------------------------------------------------------  */
-
-extern int eth_init(bd_t *bd);
-extern void eth_halt(void);
-extern int eth_rx(void);
-extern int eth_send(volatile void *packet, int length);
 
 #ifdef SHARED_RESOURCES
-	extern void swap_to(int device_id);
+extern void swap_to(int device_id);
+#else
+# define swap_to(x)
 #endif
 
-/*
- . This is called by  register_netdev().  It is responsible for
- . checking the portlist for the SMC9000 series chipset.  If it finds
- . one, then it will initialize the device, find the hardware information,
- . and sets up the appropriate device parameters.
- . NOTE: Interrupts are *OFF* when this procedure is called.
- .
- . NB:This shouldn't be static since it is referred to externally.
-*/
-int smc_init(void);
-
-/*
- . This is called by  unregister_netdev().  It is responsible for
- . cleaning up before the driver is finally unregistered and discarded.
-*/
-void smc_destructor(void);
-
-/*
- . The kernel calls this function when someone wants to use the device,
- . typically 'ifconfig ethX up'.
-*/
-static int smc_open(bd_t *bd);
-
-
-/*
- . This is called by the kernel in response to 'ifconfig ethX down'.  It
- . is responsible for cleaning up everything that the open routine
- . does, and maybe putting the card into a powerdown state.
-*/
-static int smc_close(void);
-
-/*
- . Configures the PHY through the MII Management interface
-*/
 #ifndef CONFIG_SMC91111_EXT_PHY
-static void smc_phy_configure(void);
+static void smc_phy_configure(struct eth_device *dev);
 #endif /* !CONFIG_SMC91111_EXT_PHY */
 
 /*
- . This is a separate procedure to handle the receipt of a packet, to
- . leave the interrupt code looking slightly cleaner
-*/
-static int smc_rcv(void);
-
-/* See if a MAC address is defined in the current environment. If so use it. If not
- . print a warning and set the environment and other globals with the default.
- . If an EEPROM is present it really should be consulted.
-*/
-int smc_get_ethaddr(bd_t *bd);
-int get_rom_mac(uchar *v_rom_mac);
-
-/*
  ------------------------------------------------------------
  .
  . Internal routines
@@ -233,125 +177,69 @@
  * packets being corrupt (shifted) on the wire, etc.  Switching to the
  * inx,outx functions fixed this problem.
  */
-static inline word SMC_inw(dword offset);
-static inline void SMC_outw(word value, dword offset);
-static inline byte SMC_inb(dword offset);
-static inline void SMC_outb(byte value, dword offset);
-static inline void SMC_insw(dword offset, volatile uchar* buf, dword len);
-static inline void SMC_outsw(dword offset, uchar* buf, dword len);
 
 #define barrier() __asm__ __volatile__("": : :"memory")
 
-static inline word SMC_inw(dword offset)
+static inline word SMC_inw(struct eth_device *dev, dword offset)
 {
 	word v;
-	v = *((volatile word*)(SMC_BASE_ADDRESS+offset));
+	v = *((volatile word*)(dev->iobase + offset));
 	barrier(); *(volatile u32*)(0xc0000000);
 	return v;
 }
 
-static inline void SMC_outw(word value, dword offset)
+static inline void SMC_outw(struct eth_device *dev, word value, dword offset)
 {
-	*((volatile word*)(SMC_BASE_ADDRESS+offset)) = value;
+	*((volatile word*)(dev->iobase + offset)) = value;
 	barrier(); *(volatile u32*)(0xc0000000);
 }
 
-static inline byte SMC_inb(dword offset)
+static inline byte SMC_inb(struct eth_device *dev, dword offset)
 {
 	word  _w;
 
-	_w = SMC_inw(offset & ~((dword)1));
+	_w = SMC_inw(dev, offset & ~((dword)1));
 	return (offset & 1) ? (byte)(_w >> 8) : (byte)(_w);
 }
 
-static inline void SMC_outb(byte value, dword offset)
+static inline void SMC_outb(struct eth_device *dev, byte value, dword offset)
 {
 	word  _w;
 
-	_w = SMC_inw(offset & ~((dword)1));
+	_w = SMC_inw(dev, offset & ~((dword)1));
 	if (offset & 1)
-			*((volatile word*)(SMC_BASE_ADDRESS+(offset & ~((dword)1)))) = (value<<8) | (_w & 0x00ff);
+		*((volatile word*)(dev->iobase + (offset & ~((dword)1)))) =
+			(value<<8) | (_w & 0x00ff);
 	else
-			*((volatile word*)(SMC_BASE_ADDRESS+offset)) = value | (_w & 0xff00);
+		*((volatile word*)(dev->iobase + offset)) =
+			value | (_w & 0xff00);
 }
 
-static inline void SMC_insw(dword offset, volatile uchar* buf, dword len)
+static inline void SMC_insw(struct eth_device *dev, dword offset,
+	volatile uchar* buf, dword len)
 {
 	volatile word *p = (volatile word *)buf;
 
 	while (len-- > 0) {
-		*p++ = SMC_inw(offset);
+		*p++ = SMC_inw(dev, offset);
 		barrier();
 		*((volatile u32*)(0xc0000000));
 	}
 }
 
-static inline void SMC_outsw(dword offset, uchar* buf, dword len)
+static inline void SMC_outsw(struct eth_device *dev, dword offset,
+	uchar* buf, dword len)
 {
 	volatile word *p = (volatile word *)buf;
 
 	while (len-- > 0) {
-		SMC_outw(*p++, offset);
+		SMC_outw(dev, *p++, offset);
 		barrier();
 		*(volatile u32*)(0xc0000000);
 	}
 }
 #endif  /* CONFIG_SMC_USE_IOFUNCS */
 
-static char unsigned smc_mac_addr[6] = {0x02, 0x80, 0xad, 0x20, 0x31, 0xb8};
-
-/*
- * This function must be called before smc_open() if you want to override
- * the default mac address.
- */
-
-void smc_set_mac_addr(const unsigned char *addr) {
-	int i;
-
-	for (i=0; i < sizeof(smc_mac_addr); i++){
-		smc_mac_addr[i] = addr[i];
-	}
-}
-
-/*
- * smc_get_macaddr is no longer used. If you want to override the default
- * mac address, call smc_get_mac_addr as a part of the board initialization.
- */
-
-#if 0
-void smc_get_macaddr( byte *addr ) {
-	/* MAC ADDRESS AT FLASHBLOCK 1 / OFFSET 0x10 */
-	unsigned char *dnp1110_mac = (unsigned char *) (0xE8000000 + 0x20010);
-	int i;
-
-
-	for (i=0; i<6; i++) {
-	    addr[0] = *(dnp1110_mac+0);
-	    addr[1] = *(dnp1110_mac+1);
-	    addr[2] = *(dnp1110_mac+2);
-	    addr[3] = *(dnp1110_mac+3);
-	    addr[4] = *(dnp1110_mac+4);
-	    addr[5] = *(dnp1110_mac+5);
-	}
-}
-#endif /* 0 */
-
-/***********************************************
- * Show available memory		       *
- ***********************************************/
-void dump_memory_info(void)
-{
-	word mem_info;
-	word old_bank;
-
-	old_bank = SMC_inw(BANK_SELECT)&0xF;
-
-	SMC_SELECT_BANK(0);
-	mem_info = SMC_inw( MIR_REG );
-	PRINTK2("Memory: %4d available\n", (mem_info >> 8)*2048);
-
-	SMC_SELECT_BANK(old_bank);
-}
 /*
  . A rather simple routine to print out a packet for debugging purposes.
 */
@@ -361,35 +249,15 @@
 
 #define tx_done(dev) 1
 
-
-/* this does a soft reset on the device */
-static void smc_reset( void );
-
-/* Enable Interrupts, Receive, and Transmit */
-static void smc_enable( void );
-
-/* this puts the device in an inactive state */
-static void smc_shutdown( void );
-
-/* Routines to Read and Write the PHY Registers across the
-   MII Management Interface
-*/
-
-#ifndef CONFIG_SMC91111_EXT_PHY
-static word smc_read_phy_register(byte phyreg);
-static void smc_write_phy_register(byte phyreg, word phydata);
-#endif /* !CONFIG_SMC91111_EXT_PHY */
-
-
-static int poll4int (byte mask, int timeout)
+static int poll4int (struct eth_device *dev, byte mask, int timeout)
 {
 	int tmo = get_timer (0) + timeout * CONFIG_SYS_HZ;
 	int is_timeout = 0;
-	word old_bank = SMC_inw (BSR_REG);
+	word old_bank = SMC_inw (dev, BSR_REG);
 
 	PRINTK2 ("Polling...\n");
-	SMC_SELECT_BANK (2);
-	while ((SMC_inw (SMC91111_INT_REG) & mask) == 0) {
+	SMC_SELECT_BANK (dev, 2);
+	while ((SMC_inw (dev, SMC91111_INT_REG) & mask) == 0) {
 		if (get_timer (0) >= tmo) {
 			is_timeout = 1;
 			break;
@@ -397,7 +265,7 @@
 	}
 
 	/* restore old bank selection */
-	SMC_SELECT_BANK (old_bank);
+	SMC_SELECT_BANK (dev, old_bank);
 
 	if (is_timeout)
 		return 1;
@@ -406,12 +274,12 @@
 }
 
 /* Only one release command at a time, please */
-static inline void smc_wait_mmu_release_complete (void)
+static inline void smc_wait_mmu_release_complete (struct eth_device *dev)
 {
 	int count = 0;
 
 	/* assume bank 2 selected */
-	while (SMC_inw (MMU_CMD_REG) & MC_BUSY) {
+	while (SMC_inw (dev, MMU_CMD_REG) & MC_BUSY) {
 		udelay (1);	/* Wait until not busy */
 		if (++count > 200)
 			break;
@@ -435,49 +303,50 @@
  .	5.  clear all interrupts
  .
 */
-static void smc_reset (void)
+static void smc_reset (struct eth_device *dev)
 {
 	PRINTK2 ("%s: smc_reset\n", SMC_DEV_NAME);
 
 	/* This resets the registers mostly to defaults, but doesn't
 	   affect EEPROM.  That seems unnecessary */
-	SMC_SELECT_BANK (0);
-	SMC_outw (RCR_SOFTRST, RCR_REG);
+	SMC_SELECT_BANK (dev, 0);
+	SMC_outw (dev, RCR_SOFTRST, RCR_REG);
 
 	/* Setup the Configuration Register */
 	/* This is necessary because the CONFIG_REG is not affected */
 	/* by a soft reset */
 
-	SMC_SELECT_BANK (1);
+	SMC_SELECT_BANK (dev, 1);
 #if defined(CONFIG_SMC91111_EXT_PHY)
-	SMC_outw (CONFIG_DEFAULT | CONFIG_EXT_PHY, CONFIG_REG);
+	SMC_outw (dev, CONFIG_DEFAULT | CONFIG_EXT_PHY, CONFIG_REG);
 #else
-	SMC_outw (CONFIG_DEFAULT, CONFIG_REG);
+	SMC_outw (dev, CONFIG_DEFAULT, CONFIG_REG);
 #endif
 
 
 	/* Release from possible power-down state */
 	/* Configuration register is not affected by Soft Reset */
-	SMC_outw (SMC_inw (CONFIG_REG) | CONFIG_EPH_POWER_EN, CONFIG_REG);
+	SMC_outw (dev, SMC_inw (dev, CONFIG_REG) | CONFIG_EPH_POWER_EN,
+		CONFIG_REG);
 
-	SMC_SELECT_BANK (0);
+	SMC_SELECT_BANK (dev, 0);
 
 	/* this should pause enough for the chip to be happy */
 	udelay (10);
 
 	/* Disable transmit and receive functionality */
-	SMC_outw (RCR_CLEAR, RCR_REG);
-	SMC_outw (TCR_CLEAR, TCR_REG);
+	SMC_outw (dev, RCR_CLEAR, RCR_REG);
+	SMC_outw (dev, TCR_CLEAR, TCR_REG);
 
 	/* set the control register */
-	SMC_SELECT_BANK (1);
-	SMC_outw (CTL_DEFAULT, CTL_REG);
+	SMC_SELECT_BANK (dev, 1);
+	SMC_outw (dev, CTL_DEFAULT, CTL_REG);
 
 	/* Reset the MMU */
-	SMC_SELECT_BANK (2);
-	smc_wait_mmu_release_complete ();
-	SMC_outw (MC_RESET, MMU_CMD_REG);
-	while (SMC_inw (MMU_CMD_REG) & MC_BUSY)
+	SMC_SELECT_BANK (dev, 2);
+	smc_wait_mmu_release_complete (dev);
+	SMC_outw (dev, MC_RESET, MMU_CMD_REG);
+	while (SMC_inw (dev, MMU_CMD_REG) & MC_BUSY)
 		udelay (1);	/* Wait until not busy */
 
 	/* Note:  It doesn't seem that waiting for the MMU busy is needed here,
@@ -485,7 +354,7 @@
 	   of issuing another MMU command right after this */
 
 	/* Disable all interrupts */
-	SMC_outb (0, IM_REG);
+	SMC_outb (dev, 0, IM_REG);
 }
 
 /*
@@ -496,20 +365,20 @@
  .	2.  Enable the receiver
  .	3.  Enable interrupts
 */
-static void smc_enable()
+static void smc_enable(struct eth_device *dev)
 {
 	PRINTK2("%s: smc_enable\n", SMC_DEV_NAME);
-	SMC_SELECT_BANK( 0 );
+	SMC_SELECT_BANK( dev, 0 );
 	/* see the header file for options in TCR/RCR DEFAULT*/
-	SMC_outw( TCR_DEFAULT, TCR_REG );
-	SMC_outw( RCR_DEFAULT, RCR_REG );
+	SMC_outw( dev, TCR_DEFAULT, TCR_REG );
+	SMC_outw( dev, RCR_DEFAULT, RCR_REG );
 
 	/* clear MII_DIS */
 /*	smc_write_phy_register(PHY_CNTL_REG, 0x0000); */
 }
 
 /*
- . Function: smc_shutdown
+ . Function: smc_halt
  . Purpose:  closes down the SMC91xxx chip.
  . Method:
  .	1. zero the interrupt mask
@@ -522,26 +391,25 @@
  .	the manual says that it will wake up in response to any I/O requests
  .	in the register space.	 Empirical results do not show this working.
 */
-static void smc_shutdown()
+static void smc_halt(struct eth_device *dev)
 {
-	PRINTK2(CARDNAME ": smc_shutdown\n");
+	PRINTK2("%s: smc_halt\n", SMC_DEV_NAME);
 
 	/* no more interrupts for me */
-	SMC_SELECT_BANK( 2 );
-	SMC_outb( 0, IM_REG );
+	SMC_SELECT_BANK( dev, 2 );
+	SMC_outb( dev, 0, IM_REG );
 
 	/* and tell the card to stay away from that nasty outside world */
-	SMC_SELECT_BANK( 0 );
-	SMC_outb( RCR_CLEAR, RCR_REG );
-	SMC_outb( TCR_CLEAR, TCR_REG );
-#ifdef SHARED_RESOURCES
+	SMC_SELECT_BANK( dev, 0 );
+	SMC_outb( dev, RCR_CLEAR, RCR_REG );
+	SMC_outb( dev, TCR_CLEAR, TCR_REG );
+
 	swap_to(FLASH);
-#endif
 }
 
 
 /*
- . Function:  smc_hardware_send_packet(struct net_device * )
+ . Function:  smc_send(struct net_device * )
  . Purpose:
  .	This sends the actual packet to the SMC9xxx chip.
  .
@@ -558,10 +426,10 @@
  .	Enable the transmit interrupt, so I know if it failed
  .	Free the kernel data if I actually sent it.
 */
-static int smc_send_packet (volatile void *packet, int packet_length)
+static int smc_send(struct eth_device *dev, volatile void *packet,
+	int packet_length)
 {
 	byte packet_no;
-	unsigned long ioaddr;
 	byte *buf;
 	int length;
 	int numPages;
@@ -572,9 +440,9 @@
 	word saved_ptr;
 
 	/* save PTR and PNR registers before manipulation */
-	SMC_SELECT_BANK (2);
-	saved_pnr = SMC_inb( PN_REG );
-	saved_ptr = SMC_inw( PTR_REG );
+	SMC_SELECT_BANK (dev, 2);
+	saved_pnr = SMC_inb( dev, PN_REG );
+	saved_ptr = SMC_inw( dev, PTR_REG );
 
 	PRINTK3 ("%s: smc_hardware_send_packet\n", SMC_DEV_NAME);
 
@@ -601,8 +469,8 @@
 	}
 
 	/* now, try to allocate the memory */
-	SMC_SELECT_BANK (2);
-	SMC_outw (MC_ALLOC | numPages, MMU_CMD_REG);
+	SMC_SELECT_BANK (dev, 2);
+	SMC_outw (dev, MC_ALLOC | numPages, MMU_CMD_REG);
 
 	/* FIXME: the ALLOC_INT bit never gets set *
 	 * so the following will always give a	   *
@@ -615,10 +483,10 @@
 	try++;
 	time_out = MEMORY_WAIT_TIME;
 	do {
-		status = SMC_inb (SMC91111_INT_REG);
+		status = SMC_inb (dev, SMC91111_INT_REG);
 		if (status & IM_ALLOC_INT) {
 			/* acknowledge the interrupt */
-			SMC_outb (IM_ALLOC_INT, SMC91111_INT_REG);
+			SMC_outb (dev, IM_ALLOC_INT, SMC91111_INT_REG);
 			break;
 		}
 	} while (--time_out);
@@ -635,14 +503,10 @@
 	PRINTK2 ("%s: memory allocation, try %d succeeded ...\n",
 		 SMC_DEV_NAME, try);
 
-	/* I can send the packet now.. */
-
-	ioaddr = SMC_BASE_ADDRESS;
-
 	buf = (byte *) packet;
 
 	/* If I get here, I _know_ there is a packet slot waiting for me */
-	packet_no = SMC_inb (AR_REG);
+	packet_no = SMC_inb (dev, AR_REG);
 	if (packet_no & AR_FAILED) {
 		/* or isn't there?  BAD CHIP! */
 		printf ("%s: Memory allocation failed. \n", SMC_DEV_NAME);
@@ -651,20 +515,20 @@
 
 	/* we have a packet address, so tell the card to use it */
 #ifndef CONFIG_XAENIAX
-	SMC_outb (packet_no, PN_REG);
+	SMC_outb (dev, packet_no, PN_REG);
 #else
 	/* On Xaeniax board, we can't use SMC_outb here because that way
 	 * the Allocate MMU command will end up written to the command register
 	 * as well, which will lead to a problem.
 	 */
-	SMC_outl (packet_no << 16, 0);
+	SMC_outl (dev, packet_no << 16, 0);
 #endif
 	/* do not write new ptr value if Write data fifo not empty */
 	while ( saved_ptr & PTR_NOTEMPTY )
 		printf ("Write data fifo not empty!\n");
 
 	/* point to the beginning of the packet */
-	SMC_outw (PTR_AUTOINC, PTR_REG);
+	SMC_outw (dev, PTR_AUTOINC, PTR_REG);
 
 	PRINTK3 ("%s: Trying to xmit packet of length %x\n",
 		 SMC_DEV_NAME, length);
@@ -677,11 +541,11 @@
 	/* send the packet length ( +6 for status, length and ctl byte )
 	   and the status word ( set to zeros ) */
 #ifdef USE_32_BIT
-	SMC_outl ((length + 6) << 16, SMC91111_DATA_REG);
+	SMC_outl (dev, (length + 6) << 16, SMC91111_DATA_REG);
 #else
-	SMC_outw (0, SMC91111_DATA_REG);
+	SMC_outw (dev, 0, SMC91111_DATA_REG);
 	/* send the packet length ( +6 for status words, length, and ctl */
-	SMC_outw ((length + 6), SMC91111_DATA_REG);
+	SMC_outw (dev, (length + 6), SMC91111_DATA_REG);
 #endif
 
 	/* send the actual data
@@ -692,10 +556,10 @@
 	   . almost as much time as is saved?
 	 */
 #ifdef USE_32_BIT
-	SMC_outsl (SMC91111_DATA_REG, buf, length >> 2);
+	SMC_outsl (dev, SMC91111_DATA_REG, buf, length >> 2);
 #ifndef CONFIG_XAENIAX
 	if (length & 0x2)
-		SMC_outw (*((word *) (buf + (length & 0xFFFFFFFC))),
+		SMC_outw (dev, *((word *) (buf + (length & 0xFFFFFFFC))),
 			  SMC91111_DATA_REG);
 #else
 	/* On XANEIAX, we can only use 32-bit writes, so we need to handle
@@ -703,48 +567,48 @@
 	 */
 	if ((length & 3) == 3) {
 		u16 * ptr = (u16*) &buf[length-3];
-		SMC_outl((*ptr) | ((0x2000 | buf[length-1]) << 16),
+		SMC_outl(dev, (*ptr) | ((0x2000 | buf[length-1]) << 16),
 				SMC91111_DATA_REG);
 	} else if ((length & 2) == 2) {
 		u16 * ptr = (u16*) &buf[length-2];
-		SMC_outl(*ptr, SMC91111_DATA_REG);
+		SMC_outl(dev, *ptr, SMC91111_DATA_REG);
 	} else if (length & 1) {
-		SMC_outl((0x2000 | buf[length-1]), SMC91111_DATA_REG);
+		SMC_outl(dev, (0x2000 | buf[length-1]), SMC91111_DATA_REG);
 	} else {
-		SMC_outl(0, SMC91111_DATA_REG);
+		SMC_outl(dev, 0, SMC91111_DATA_REG);
 	}
 #endif
 #else
-	SMC_outsw (SMC91111_DATA_REG, buf, (length) >> 1);
+	SMC_outsw (dev, SMC91111_DATA_REG, buf, (length) >> 1);
 #endif /* USE_32_BIT */
 
 #ifndef CONFIG_XAENIAX
 	/* Send the last byte, if there is one.	  */
 	if ((length & 1) == 0) {
-		SMC_outw (0, SMC91111_DATA_REG);
+		SMC_outw (dev, 0, SMC91111_DATA_REG);
 	} else {
-		SMC_outw (buf[length - 1] | 0x2000, SMC91111_DATA_REG);
+		SMC_outw (dev, buf[length - 1] | 0x2000, SMC91111_DATA_REG);
 	}
 #endif
 
 	/* and let the chipset deal with it */
-	SMC_outw (MC_ENQUEUE, MMU_CMD_REG);
+	SMC_outw (dev, MC_ENQUEUE, MMU_CMD_REG);
 
 	/* poll for TX INT */
-	/* if (poll4int (IM_TX_INT, SMC_TX_TIMEOUT)) { */
+	/* if (poll4int (dev, IM_TX_INT, SMC_TX_TIMEOUT)) { */
 	/* poll for TX_EMPTY INT - autorelease enabled */
-	if (poll4int(IM_TX_EMPTY_INT, SMC_TX_TIMEOUT)) {
+	if (poll4int(dev, IM_TX_EMPTY_INT, SMC_TX_TIMEOUT)) {
 		/* sending failed */
 		PRINTK2 ("%s: TX timeout, sending failed...\n", SMC_DEV_NAME);
 
 		/* release packet */
 		/* no need to release, MMU does that now */
 #ifdef CONFIG_XAENIAX
-		 SMC_outw (MC_FREEPKT, MMU_CMD_REG);
+		 SMC_outw (dev, MC_FREEPKT, MMU_CMD_REG);
 #endif
 
 		/* wait for MMU getting ready (low) */
-		while (SMC_inw (MMU_CMD_REG) & MC_BUSY) {
+		while (SMC_inw (dev, MMU_CMD_REG) & MC_BUSY) {
 			udelay (10);
 		}
 
@@ -754,7 +618,7 @@
 		return 0;
 	} else {
 		/* ack. int */
-		SMC_outb (IM_TX_EMPTY_INT, SMC91111_INT_REG);
+		SMC_outb (dev, IM_TX_EMPTY_INT, SMC91111_INT_REG);
 		/* SMC_outb (IM_TX_INT, SMC91111_INT_REG); */
 		PRINTK2 ("%s: Sent packet of length %d \n", SMC_DEV_NAME,
 			 length);
@@ -762,11 +626,11 @@
 		/* release packet */
 		/* no need to release, MMU does that now */
 #ifdef CONFIG_XAENIAX
-		SMC_outw (MC_FREEPKT, MMU_CMD_REG);
+		SMC_outw (dev, MC_FREEPKT, MMU_CMD_REG);
 #endif
 
 		/* wait for MMU getting ready (low) */
-		while (SMC_inw (MMU_CMD_REG) & MC_BUSY) {
+		while (SMC_inw (dev, MMU_CMD_REG) & MC_BUSY) {
 			udelay (10);
 		}
 
@@ -777,78 +641,62 @@
 
 	/* restore previously saved registers */
 #ifndef CONFIG_XAENIAX
-	SMC_outb( saved_pnr, PN_REG );
+	SMC_outb( dev, saved_pnr, PN_REG );
 #else
 	/* On Xaeniax board, we can't use SMC_outb here because that way
 	 * the Allocate MMU command will end up written to the command register
 	 * as well, which will lead to a problem.
 	 */
-	SMC_outl(saved_pnr << 16, 0);
+	SMC_outl(dev, saved_pnr << 16, 0);
 #endif
-	SMC_outw( saved_ptr, PTR_REG );
+	SMC_outw( dev, saved_ptr, PTR_REG );
 
 	return length;
 }
 
-/*-------------------------------------------------------------------------
- |
- | smc_destructor( struct net_device * dev )
- |   Input parameters:
- |	dev, pointer to the device structure
- |
- |   Output:
- |	None.
- |
- ---------------------------------------------------------------------------
-*/
-void smc_destructor()
-{
-	PRINTK2(CARDNAME ": smc_destructor\n");
-}
-
-
 /*
  * Open and Initialize the board
  *
  * Set up everything, reset the card, etc ..
  *
  */
-static int smc_open (bd_t * bd)
+static int smc_init(struct eth_device *dev, bd_t *bd)
 {
-	int i, err;
+	int i;
 
-	PRINTK2 ("%s: smc_open\n", SMC_DEV_NAME);
+	swap_to(ETHERNET);
+
+	PRINTK2 ("%s: smc_init\n", SMC_DEV_NAME);
 
 	/* reset the hardware */
-	smc_reset ();
-	smc_enable ();
+	smc_reset (dev);
+	smc_enable (dev);
 
 	/* Configure the PHY */
 #ifndef CONFIG_SMC91111_EXT_PHY
-	smc_phy_configure ();
+	smc_phy_configure (dev);
 #endif
 
 	/* conservative setting (10Mbps, HalfDuplex, no AutoNeg.) */
-/*	SMC_SELECT_BANK(0); */
-/*	SMC_outw(0, RPC_REG); */
-	SMC_SELECT_BANK (1);
+/*	SMC_SELECT_BANK(dev, 0); */
+/*	SMC_outw(dev, 0, RPC_REG); */
+	SMC_SELECT_BANK (dev, 1);
 
-	err = smc_get_ethaddr (bd);	/* set smc_mac_addr, and sync it with u-boot globals */
-	if (err < 0)
-		return -1;
 #ifdef USE_32_BIT
 	for (i = 0; i < 6; i += 2) {
 		word address;
 
-		address = smc_mac_addr[i + 1] << 8;
-		address |= smc_mac_addr[i];
-		SMC_outw (address, (ADDR0_REG + i));
+		address = dev->enetaddr[i + 1] << 8;
+		address |= dev->enetaddr[i];
+		SMC_outw(dev, address, (ADDR0_REG + i));
 	}
 #else
 	for (i = 0; i < 6; i++)
-		SMC_outb (smc_mac_addr[i], (ADDR0_REG + i));
+		SMC_outb(dev, dev->enetaddr[i], (ADDR0_REG + i));
 #endif
 
+	printf(SMC_DEV_NAME ": MAC %pM\n", dev->enetaddr);
+
 	return 0;
 }
 
@@ -864,7 +712,7 @@
  . o otherwise, read in the packet
  --------------------------------------------------------------
 */
-static int smc_rcv()
+static int smc_rcv(struct eth_device *dev)
 {
 	int	packet_number;
 	word	status;
@@ -876,12 +724,12 @@
 	byte saved_pnr;
 	word saved_ptr;
 
-	SMC_SELECT_BANK(2);
+	SMC_SELECT_BANK(dev, 2);
 	/* save PTR and PTR registers */
-	saved_pnr = SMC_inb( PN_REG );
-	saved_ptr = SMC_inw( PTR_REG );
+	saved_pnr = SMC_inb( dev, PN_REG );
+	saved_ptr = SMC_inw( dev, PTR_REG );
 
-	packet_number = SMC_inw( RXFIFO_REG );
+	packet_number = SMC_inw( dev, RXFIFO_REG );
 
 	if ( packet_number & RXFIFO_REMPTY ) {
 
@@ -890,16 +738,16 @@
 
 	PRINTK3("%s: smc_rcv\n", SMC_DEV_NAME);
 	/*  start reading from the start of the packet */
-	SMC_outw( PTR_READ | PTR_RCV | PTR_AUTOINC, PTR_REG );
+	SMC_outw( dev, PTR_READ | PTR_RCV | PTR_AUTOINC, PTR_REG );
 
 	/* First two words are status and packet_length */
 #ifdef USE_32_BIT
-	stat_len = SMC_inl(SMC91111_DATA_REG);
+	stat_len = SMC_inl(dev, SMC91111_DATA_REG);
 	status = stat_len & 0xffff;
 	packet_length = stat_len >> 16;
 #else
-	status		= SMC_inw( SMC91111_DATA_REG );
-	packet_length	= SMC_inw( SMC91111_DATA_REG );
+	status		= SMC_inw( dev, SMC91111_DATA_REG );
+	packet_length	= SMC_inw( dev, SMC91111_DATA_REG );
 #endif
 
 	packet_length &= 0x07ff;  /* mask off top bits */
@@ -923,20 +771,23 @@
 		   to send the DWORDs or the bytes first, or some
 		   mixture.  A mixture might improve already slow PIO
 		   performance	*/
-		SMC_insl( SMC91111_DATA_REG , NetRxPackets[0], packet_length >> 2 );
+		SMC_insl( dev, SMC91111_DATA_REG, NetRxPackets[0],
+			packet_length >> 2 );
 		/* read the left over bytes */
 		if (packet_length & 3) {
 			int i;
 
-			byte *tail = (byte *)(NetRxPackets[0] + (packet_length & ~3));
-			dword leftover = SMC_inl(SMC91111_DATA_REG);
+			byte *tail = (byte *)(NetRxPackets[0] +
+				(packet_length & ~3));
+			dword leftover = SMC_inl(dev, SMC91111_DATA_REG);
 			for (i=0; i<(packet_length & 3); i++)
 				*tail++ = (byte) (leftover >> (8*i)) & 0xff;
 		}
 #else
 		PRINTK3(" Reading %d words and %d byte(s) \n",
 			(packet_length >> 1 ), packet_length & 1 );
-		SMC_insw(SMC91111_DATA_REG , NetRxPackets[0], packet_length >> 1);
+		SMC_insw(dev, SMC91111_DATA_REG , NetRxPackets[0],
+			packet_length >> 1);
 
 #endif /* USE_32_BIT */
 
@@ -950,26 +801,26 @@
 		is_error = 1;
 	}
 
-	while ( SMC_inw( MMU_CMD_REG ) & MC_BUSY )
+	while ( SMC_inw( dev, MMU_CMD_REG ) & MC_BUSY )
 		udelay(1); /* Wait until not busy */
 
 	/*  error or good, tell the card to get rid of this packet */
-	SMC_outw( MC_RELEASE, MMU_CMD_REG );
+	SMC_outw( dev, MC_RELEASE, MMU_CMD_REG );
 
-	while ( SMC_inw( MMU_CMD_REG ) & MC_BUSY )
+	while ( SMC_inw( dev, MMU_CMD_REG ) & MC_BUSY )
 		udelay(1); /* Wait until not busy */
 
 	/* restore saved registers */
 #ifndef CONFIG_XAENIAX
-	SMC_outb( saved_pnr, PN_REG );
+	SMC_outb( dev, saved_pnr, PN_REG );
 #else
 	/* On Xaeniax board, we can't use SMC_outb here because that way
 	 * the Allocate MMU command will end up written to the command register
 	 * as well, which will lead to a problem.
 	 */
-	SMC_outl( saved_pnr << 16, 0);
+	SMC_outl( dev, saved_pnr << 16, 0);
 #endif
-	SMC_outw( saved_ptr, PTR_REG );
+	SMC_outw( dev, saved_ptr, PTR_REG );
 
 	if (!is_error) {
 		/* Pass the packet up to the protocol layers. */
@@ -982,43 +833,24 @@
 }
 
 
-/*----------------------------------------------------
- . smc_close
- .
- . this makes the board clean up everything that it can
- . and not talk to the outside world.	Caused by
- . an 'ifconfig ethX down'
- .
- -----------------------------------------------------*/
-static int smc_close()
-{
-	PRINTK2("%s: smc_close\n", SMC_DEV_NAME);
-
-	/* clear everything */
-	smc_shutdown();
-
-	return 0;
-}
-
-
 #if 0
 /*------------------------------------------------------------
  . Modify a bit in the LAN91C111 register set
  .-------------------------------------------------------------*/
-static word smc_modify_regbit(int bank, int ioaddr, int reg,
+static word smc_modify_regbit(struct eth_device *dev, int bank, int ioaddr, int reg,
 	unsigned int bit, int val)
 {
 	word regval;
 
-	SMC_SELECT_BANK( bank );
+	SMC_SELECT_BANK( dev, bank );
 
-	regval = SMC_inw( reg );
+	regval = SMC_inw( dev, reg );
 	if (val)
 		regval |= bit;
 	else
 		regval &= ~bit;
 
-	SMC_outw( regval, 0 );
+	SMC_outw( dev, regval, 0 );
 	return(regval);
 }
 
@@ -1026,10 +858,10 @@
 /*------------------------------------------------------------
  . Retrieve a bit in the LAN91C111 register set
  .-------------------------------------------------------------*/
-static int smc_get_regbit(int bank, int ioaddr, int reg, unsigned int bit)
+static int smc_get_regbit(struct eth_device *dev, int bank, int ioaddr, int reg, unsigned int bit)
 {
-	SMC_SELECT_BANK( bank );
-	if ( SMC_inw( reg ) & bit)
+	SMC_SELECT_BANK( dev, bank );
+	if ( SMC_inw( dev, reg ) & bit)
 		return(1);
 	else
 		return(0);
@@ -1039,20 +871,20 @@
 /*------------------------------------------------------------
  . Modify a LAN91C111 register (word access only)
  .-------------------------------------------------------------*/
-static void smc_modify_reg(int bank, int ioaddr, int reg, word val)
+static void smc_modify_reg(struct eth_device *dev, int bank, int ioaddr, int reg, word val)
 {
-	SMC_SELECT_BANK( bank );
-	SMC_outw( val, reg );
+	SMC_SELECT_BANK( dev, bank );
+	SMC_outw( dev, val, reg );
 }
 
 
 /*------------------------------------------------------------
  . Retrieve a LAN91C111 register (word access only)
  .-------------------------------------------------------------*/
-static int smc_get_reg(int bank, int ioaddr, int reg)
+static int smc_get_reg(struct eth_device *dev, int bank, int ioaddr, int reg)
 {
-	SMC_SELECT_BANK( bank );
-	return(SMC_inw( reg ));
+	SMC_SELECT_BANK( dev, bank );
+	return(SMC_inw( dev, reg ));
 }
 
 #endif /* 0 */
@@ -1105,7 +937,7 @@
  . Reads a register from the MII Management serial interface
  .-------------------------------------------------------------*/
 #ifndef CONFIG_SMC91111_EXT_PHY
-static word smc_read_phy_register (byte phyreg)
+static word smc_read_phy_register (struct eth_device *dev, byte phyreg)
 {
 	int oldBank;
 	int i;
@@ -1168,13 +1000,13 @@
 	bits[clk_idx++] = 0;
 
 	/* Save the current bank */
-	oldBank = SMC_inw (BANK_SELECT);
+	oldBank = SMC_inw (dev, BANK_SELECT);
 
 	/* Select bank 3 */
-	SMC_SELECT_BANK (3);
+	SMC_SELECT_BANK (dev, 3);
 
 	/* Get the current MII register value */
-	mii_reg = SMC_inw (MII_REG);
+	mii_reg = SMC_inw (dev, MII_REG);
 
 	/* Turn off all MII Interface bits */
 	mii_reg &= ~(MII_MDOE | MII_MCLK | MII_MDI | MII_MDO);
@@ -1182,23 +1014,23 @@
 	/* Clock all 64 cycles */
 	for (i = 0; i < sizeof bits; ++i) {
 		/* Clock Low - output data */
-		SMC_outw (mii_reg | bits[i], MII_REG);
+		SMC_outw (dev, mii_reg | bits[i], MII_REG);
 		udelay (SMC_PHY_CLOCK_DELAY);
 
 
 		/* Clock Hi - input data */
-		SMC_outw (mii_reg | bits[i] | MII_MCLK, MII_REG);
+		SMC_outw (dev, mii_reg | bits[i] | MII_MCLK, MII_REG);
 		udelay (SMC_PHY_CLOCK_DELAY);
-		bits[i] |= SMC_inw (MII_REG) & MII_MDI;
+		bits[i] |= SMC_inw (dev, MII_REG) & MII_MDI;
 	}
 
 	/* Return to idle state */
 	/* Set clock to low, data to low, and output tristated */
-	SMC_outw (mii_reg, MII_REG);
+	SMC_outw (dev, mii_reg, MII_REG);
 	udelay (SMC_PHY_CLOCK_DELAY);
 
 	/* Restore original bank select */
-	SMC_SELECT_BANK (oldBank);
+	SMC_SELECT_BANK (dev, oldBank);
 
 	/* Recover input data */
 	phydata = 0;
@@ -1222,7 +1054,8 @@
 /*------------------------------------------------------------
  . Writes a register to the MII Management serial interface
  .-------------------------------------------------------------*/
-static void smc_write_phy_register (byte phyreg, word phydata)
+static void smc_write_phy_register (struct eth_device *dev, byte phyreg,
+	word phydata)
 {
 	int oldBank;
 	int i;
@@ -1288,13 +1121,13 @@
 	bits[clk_idx++] = 0;
 
 	/* Save the current bank */
-	oldBank = SMC_inw (BANK_SELECT);
+	oldBank = SMC_inw (dev, BANK_SELECT);
 
 	/* Select bank 3 */
-	SMC_SELECT_BANK (3);
+	SMC_SELECT_BANK (dev, 3);
 
 	/* Get the current MII register value */
-	mii_reg = SMC_inw (MII_REG);
+	mii_reg = SMC_inw (dev, MII_REG);
 
 	/* Turn off all MII Interface bits */
 	mii_reg &= ~(MII_MDOE | MII_MCLK | MII_MDI | MII_MDO);
@@ -1302,23 +1135,23 @@
 	/* Clock all cycles */
 	for (i = 0; i < sizeof bits; ++i) {
 		/* Clock Low - output data */
-		SMC_outw (mii_reg | bits[i], MII_REG);
+		SMC_outw (dev, mii_reg | bits[i], MII_REG);
 		udelay (SMC_PHY_CLOCK_DELAY);
 
 
 		/* Clock Hi - input data */
-		SMC_outw (mii_reg | bits[i] | MII_MCLK, MII_REG);
+		SMC_outw (dev, mii_reg | bits[i] | MII_MCLK, MII_REG);
 		udelay (SMC_PHY_CLOCK_DELAY);
-		bits[i] |= SMC_inw (MII_REG) & MII_MDI;
+		bits[i] |= SMC_inw (dev, MII_REG) & MII_MDI;
 	}
 
 	/* Return to idle state */
 	/* Set clock to low, data to low, and output tristated */
-	SMC_outw (mii_reg, MII_REG);
+	SMC_outw (dev, mii_reg, MII_REG);
 	udelay (SMC_PHY_CLOCK_DELAY);
 
 	/* Restore original bank select */
-	SMC_SELECT_BANK (oldBank);
+	SMC_SELECT_BANK (dev, oldBank);
 
 #if (SMC_DEBUG > 2 )
 	printf ("smc_write_phy_register(): phyaddr=%x,phyreg=%x,phydata=%x\n",
@@ -1345,7 +1178,7 @@
  . smc_phy_fixed() if the user has requested a certain config.
  .-------------------------------------------------------------*/
 #ifndef CONFIG_SMC91111_EXT_PHY
-static void smc_phy_configure ()
+static void smc_phy_configure (struct eth_device *dev)
 {
 	int timeout;
 	byte phyaddr;
@@ -1361,12 +1194,12 @@
 	phyaddr = SMC_PHY_ADDR;
 
 	/* Reset the PHY, setting all other bits to zero */
-	smc_write_phy_register (PHY_CNTL_REG, PHY_CNTL_RST);
+	smc_write_phy_register (dev, PHY_CNTL_REG, PHY_CNTL_RST);
 
 	/* Wait for the reset to complete, or time out */
 	timeout = 6;		/* Wait up to 3 seconds */
 	while (timeout--) {
-		if (!(smc_read_phy_register (PHY_CNTL_REG)
+		if (!(smc_read_phy_register (dev, PHY_CNTL_REG)
 		      & PHY_CNTL_RST)) {
 			/* reset complete */
 			break;
@@ -1385,14 +1218,14 @@
 
 	/* Enable PHY Interrupts (for register 18) */
 	/* Interrupts listed here are disabled */
-	smc_write_phy_register (PHY_MASK_REG, 0xffff);
+	smc_write_phy_register (dev, PHY_MASK_REG, 0xffff);
 
 	/* Configure the Receive/Phy Control register */
-	SMC_SELECT_BANK (0);
-	SMC_outw (RPC_DEFAULT, RPC_REG);
+	SMC_SELECT_BANK (dev, 0);
+	SMC_outw (dev, RPC_DEFAULT, RPC_REG);
 
 	/* Copy our capabilities from PHY_STAT_REG to PHY_AD_REG */
-	my_phy_caps = smc_read_phy_register (PHY_STAT_REG);
+	my_phy_caps = smc_read_phy_register (dev, PHY_STAT_REG);
 	my_ad_caps = PHY_AD_CSMA;	/* I am CSMA capable */
 
 	if (my_phy_caps & PHY_STAT_CAP_T4)
@@ -1411,18 +1244,18 @@
 		my_ad_caps |= PHY_AD_10_HDX;
 
 	/* Update our Auto-Neg Advertisement Register */
-	smc_write_phy_register (PHY_AD_REG, my_ad_caps);
+	smc_write_phy_register (dev, PHY_AD_REG, my_ad_caps);
 
 	/* Read the register back.  Without this, it appears that when */
 	/* auto-negotiation is restarted, sometimes it isn't ready and */
 	/* the link does not come up. */
-	smc_read_phy_register(PHY_AD_REG);
+	smc_read_phy_register(dev, PHY_AD_REG);
 
 	PRINTK2 ("%s: phy caps=%x\n", SMC_DEV_NAME, my_phy_caps);
 	PRINTK2 ("%s: phy advertised caps=%x\n", SMC_DEV_NAME, my_ad_caps);
 
 	/* Restart auto-negotiation process in order to advertise my caps */
-	smc_write_phy_register (PHY_CNTL_REG,
+	smc_write_phy_register (dev, PHY_CNTL_REG,
 				PHY_CNTL_ANEG_EN | PHY_CNTL_ANEG_RST);
 
 	/* Wait for the auto-negotiation to complete.  This may take from */
@@ -1431,7 +1264,7 @@
 	timeout = CONFIG_SMC_AUTONEG_TIMEOUT * 2;
 	while (timeout--) {
 
-		status = smc_read_phy_register (PHY_STAT_REG);
+		status = smc_read_phy_register (dev, PHY_STAT_REG);
 		if (status & PHY_STAT_ANEG_ACK) {
 			/* auto-negotiate complete */
 			break;
@@ -1447,7 +1280,7 @@
 			/* Restart auto-negotiation */
 			printf ("%s: PHY restarting auto-negotiation\n",
 				SMC_DEV_NAME);
-			smc_write_phy_register (PHY_CNTL_REG,
+			smc_write_phy_register (dev, PHY_CNTL_REG,
 						PHY_CNTL_ANEG_EN |
 						PHY_CNTL_ANEG_RST |
 						PHY_CNTL_SPEED |
@@ -1467,7 +1300,7 @@
 	}
 
 	/* Re-Configure the Receive/Phy Control register */
-	SMC_outw (RPC_DEFAULT, RPC_REG);
+	SMC_outw (dev, RPC_DEFAULT, RPC_REG);
 
 smc_phy_configure_exit:	;
 
@@ -1512,61 +1345,37 @@
 }
 #endif
 
-int eth_init(bd_t *bd) {
-#ifdef SHARED_RESOURCES
-	swap_to(ETHERNET);
-#endif
-	return (smc_open(bd));
-}
-
-void eth_halt() {
-	smc_close();
-}
-
-int eth_rx() {
-	return smc_rcv();
-}
-
-int eth_send(volatile void *packet, int length) {
-	return smc_send_packet(packet, length);
-}
-
-int smc_get_ethaddr (bd_t * bd)
+int smc91111_initialize(u8 dev_num, int base_addr)
 {
-	uchar v_mac[6];
-
-	if (!eth_getenv_enetaddr("ethaddr", v_mac)) {
-		/* get ROM mac value if any */
-		if (!get_rom_mac(v_mac)) {
-			printf("\n*** ERROR: ethaddr is NOT set !!\n");
-			return -1;
-		}
-		eth_setenv_enetaddr("ethaddr", v_mac);
-	}
-
-	smc_set_mac_addr(v_mac); /* use old function to update smc default */
-	PRINTK("Using MAC Address %pM\n", v_mac);
-	return 0;
-}
-
-int get_rom_mac (uchar *v_rom_mac)
-{
-#ifdef HARDCODE_MAC	/* used for testing or to supress run time warnings */
-	char hw_mac_addr[] = { 0x02, 0x80, 0xad, 0x20, 0x31, 0xb8 };
-
-	memcpy (v_rom_mac, hw_mac_addr, 6);
-	return (1);
-#else
+	struct smc91111_priv *priv;
+	struct eth_device *dev;
 	int i;
-	int valid_mac = 0;
 
-	SMC_SELECT_BANK (1);
-	for (i=0; i<6; i++)
-	{
-		v_rom_mac[i] = SMC_inb ((ADDR0_REG + i));
-		valid_mac |= v_rom_mac[i];
+	priv = malloc(sizeof(*priv));
+	if (!priv)
+		return 0;
+	dev = malloc(sizeof(*dev));
+	if (!dev) {
+		free(priv);
+		return 0;
 	}
 
-	return (valid_mac ? 1 : 0);
-#endif
+	priv->dev_num = dev_num;
+	dev->priv = priv;
+	dev->iobase = base_addr;
+
+	swap_to(ETHERNET);
+	SMC_SELECT_BANK(dev, 1);
+	for (i = 0; i < 6; ++i)
+		dev->enetaddr[i] = SMC_inb(dev, (ADDR0_REG + i));
+	swap_to(FLASH);
+
+	dev->init = smc_init;
+	dev->halt = smc_halt;
+	dev->send = smc_send;
+	dev->recv = smc_rcv;
+	sprintf(dev->name, "%s-%hu", SMC_DEV_NAME, dev_num);
+
+	eth_register(dev);
+	return 0;
 }
diff --git a/drivers/net/smc91111.h b/drivers/net/smc91111.h
index 967addd..bb45241 100644
--- a/drivers/net/smc91111.h
+++ b/drivers/net/smc91111.h
@@ -58,6 +58,10 @@
 typedef unsigned short			word;
 typedef unsigned long int		dword;
 
+struct smc91111_priv{
+	u8 dev_num;
+};
+
 /*
  . DEBUGGING LEVELS
  .
@@ -77,32 +81,32 @@
 #ifdef CONFIG_PXA250
 
 #ifdef CONFIG_XSENGINE
-#define	SMC_inl(r)	(*((volatile dword *)(SMC_BASE_ADDRESS+(r<<1))))
-#define	SMC_inw(r)	(*((volatile word *)(SMC_BASE_ADDRESS+(r<<1))))
-#define SMC_inb(p)  ({ \
-	unsigned int __p = (unsigned int)(SMC_BASE_ADDRESS + (p<<1)); \
+#define	SMC_inl(a,r)	(*((volatile dword *)((a)->iobase+(r<<1))))
+#define	SMC_inw(a,r)	(*((volatile word *)((a)->iobase+(r<<1))))
+#define SMC_inb(a,p)  ({ \
+	unsigned int __p = (unsigned int)((a)->iobase + (p<<1)); \
 	unsigned int __v = *(volatile unsigned short *)((__p) & ~2); \
 	if (__p & 2) __v >>= 8; \
 	else __v &= 0xff; \
 	__v; })
 #elif defined(CONFIG_XAENIAX)
-#define SMC_inl(r)	(*((volatile dword *)(SMC_BASE_ADDRESS+(r))))
-#define SMC_inw(z)	({ \
-	unsigned int __p = (unsigned int)(SMC_BASE_ADDRESS + (z)); \
+#define SMC_inl(a,r)	(*((volatile dword *)((a)->iobase+(r))))
+#define SMC_inw(a,z)	({ \
+	unsigned int __p = (unsigned int)((a)->iobase + (z)); \
 	unsigned int __v = *(volatile unsigned int *)((__p) & ~3); \
 	if (__p & 3) __v >>= 16; \
 	else __v &= 0xffff; \
 	__v; })
-#define SMC_inb(p)	({ \
-	unsigned int ___v = SMC_inw((p) & ~1); \
+#define SMC_inb(a,p)	({ \
+	unsigned int ___v = SMC_inw((a),(p) & ~1); \
 	if (p & 1) ___v >>= 8; \
 	else ___v &= 0xff; \
 	___v; })
 #else
-#define	SMC_inl(r)	(*((volatile dword *)(SMC_BASE_ADDRESS+(r))))
-#define	SMC_inw(r)	(*((volatile word *)(SMC_BASE_ADDRESS+(r))))
-#define SMC_inb(p)	({ \
-	unsigned int __p = (unsigned int)(SMC_BASE_ADDRESS + (p)); \
+#define	SMC_inl(a,r)	(*((volatile dword *)((a)->iobase+(r))))
+#define	SMC_inw(a,r)	(*((volatile word *)((a)->iobase+(r))))
+#define SMC_inb(a,p)	({ \
+	unsigned int __p = (unsigned int)((a)->iobase + (p)); \
 	unsigned int __v = *(volatile unsigned short *)((__p) & ~1); \
 	if (__p & 1) __v >>= 8; \
 	else __v &= 0xff; \
@@ -110,69 +114,69 @@
 #endif
 
 #ifdef CONFIG_XSENGINE
-#define	SMC_outl(d,r)	(*((volatile dword *)(SMC_BASE_ADDRESS+(r<<1))) = d)
-#define	SMC_outw(d,r)	(*((volatile word *)(SMC_BASE_ADDRESS+(r<<1))) = d)
+#define	SMC_outl(a,d,r)	(*((volatile dword *)((a)->iobase+(r<<1))) = d)
+#define	SMC_outw(a,d,r)	(*((volatile word *)((a)->iobase+(r<<1))) = d)
 #elif defined (CONFIG_XAENIAX)
-#define SMC_outl(d,r)	(*((volatile dword *)(SMC_BASE_ADDRESS+(r))) = d)
-#define SMC_outw(d,p)	({ \
-	dword __dwo = SMC_inl((p) & ~3); \
+#define SMC_outl(a,d,r)	(*((volatile dword *)((a)->iobase+(r))) = d)
+#define SMC_outw(a,d,p)	({ \
+	dword __dwo = SMC_inl((a),(p) & ~3); \
 	dword __dwn = (word)(d); \
 	__dwo &= ((p) & 3) ? 0x0000ffff : 0xffff0000; \
 	__dwo |= ((p) & 3) ? __dwn << 16 : __dwn; \
-	SMC_outl(__dwo, (p) & ~3); \
+	SMC_outl((a), __dwo, (p) & ~3); \
 })
 #else
-#define	SMC_outl(d,r)	(*((volatile dword *)(SMC_BASE_ADDRESS+(r))) = d)
-#define	SMC_outw(d,r)	(*((volatile word *)(SMC_BASE_ADDRESS+(r))) = d)
+#define	SMC_outl(a,d,r)	(*((volatile dword *)((a)->iobase+(r))) = d)
+#define	SMC_outw(a,d,r)	(*((volatile word *)((a)->iobase+(r))) = d)
 #endif
 
-#define	SMC_outb(d,r)	({	word __d = (byte)(d);  \
-				word __w = SMC_inw((r)&~1);  \
+#define	SMC_outb(a,d,r)	({	word __d = (byte)(d);  \
+				word __w = SMC_inw((a),(r)&~1);  \
 				__w &= ((r)&1) ? 0x00FF : 0xFF00;  \
 				__w |= ((r)&1) ? __d<<8 : __d;  \
-				SMC_outw(__w,(r)&~1);  \
+				SMC_outw((a),__w,(r)&~1);  \
 			})
 
-#define SMC_outsl(r,b,l)	({	int __i; \
+#define SMC_outsl(a,r,b,l)	({	int __i; \
 					dword *__b2; \
 					__b2 = (dword *) b; \
 					for (__i = 0; __i < l; __i++) { \
-					    SMC_outl( *(__b2 + __i), r); \
+					    SMC_outl((a), *(__b2 + __i), r); \
 					} \
 				})
 
-#define SMC_outsw(r,b,l)	({	int __i; \
+#define SMC_outsw(a,r,b,l)	({	int __i; \
 					word *__b2; \
 					__b2 = (word *) b; \
 					for (__i = 0; __i < l; __i++) { \
-					    SMC_outw( *(__b2 + __i), r); \
+					    SMC_outw((a), *(__b2 + __i), r); \
 					} \
 				})
 
-#define SMC_insl(r,b,l)		({	int __i ;  \
+#define SMC_insl(a,r,b,l)	({	int __i ;  \
 					dword *__b2;  \
 					__b2 = (dword *) b;  \
 					for (__i = 0; __i < l; __i++) {  \
-					  *(__b2 + __i) = SMC_inl(r);  \
-					  SMC_inl(0);  \
+					  *(__b2 + __i) = SMC_inl((a),(r));  \
+					  SMC_inl((a),0);  \
 					};  \
 				})
 
-#define SMC_insw(r,b,l)		({	int __i ;  \
+#define SMC_insw(a,r,b,l)		({	int __i ;  \
 					word *__b2;  \
 					__b2 = (word *) b;  \
 					for (__i = 0; __i < l; __i++) {  \
-					  *(__b2 + __i) = SMC_inw(r);  \
-					  SMC_inw(0);  \
+					  *(__b2 + __i) = SMC_inw((a),(r));  \
+					  SMC_inw((a),0);  \
 					};  \
 				})
 
-#define SMC_insb(r,b,l)		({	int __i ;  \
+#define SMC_insb(a,r,b,l)	({	int __i ;  \
 					byte *__b2;  \
 					__b2 = (byte *) b;  \
 					for (__i = 0; __i < l; __i++) {  \
-					  *(__b2 + __i) = SMC_inb(r);  \
-					  SMC_inb(0);  \
+					  *(__b2 + __i) = SMC_inb((a),(r));  \
+					  SMC_inb((a),0);  \
 					};  \
 				})
 
@@ -187,61 +191,61 @@
        ((0x00FF0000UL & _x) >>  8) |		\
        (_x  >> 24)); })
 
-#define	SMC_inl(r)	(SMC_LEON_SWAP32((*(volatile dword *)(SMC_BASE_ADDRESS+((r)<<0)))))
-#define	SMC_inl_nosw(r)	((*(volatile dword *)(SMC_BASE_ADDRESS+((r)<<0))))
-#define	SMC_inw(r)	(SMC_LEON_SWAP16((*(volatile word *)(SMC_BASE_ADDRESS+((r)<<0)))))
-#define	SMC_inw_nosw(r)	((*(volatile word *)(SMC_BASE_ADDRESS+((r)<<0))))
-#define SMC_inb(p)	({ \
-	word ___v = SMC_inw((p) & ~1); \
+#define	SMC_inl(a,r)	(SMC_LEON_SWAP32((*(volatile dword *)((a)->iobase+((r)<<0)))))
+#define	SMC_inl_nosw(a,r)	((*(volatile dword *)((a)->iobase+((r)<<0))))
+#define	SMC_inw(a,r)	(SMC_LEON_SWAP16((*(volatile word *)((a)->iobase+((r)<<0)))))
+#define	SMC_inw_nosw(a,r)	((*(volatile word *)((a)->iobase+((r)<<0))))
+#define SMC_inb(a,p)	({ \
+	word ___v = SMC_inw((a),(p) & ~1); \
 	if ((p) & 1) ___v >>= 8; \
 	else ___v &= 0xff; \
 	___v; })
 
-#define	SMC_outl(d,r)	(*(volatile dword *)(SMC_BASE_ADDRESS+((r)<<0))=SMC_LEON_SWAP32(d))
-#define	SMC_outl_nosw(d,r)	(*(volatile dword *)(SMC_BASE_ADDRESS+((r)<<0))=(d))
-#define	SMC_outw(d,r)	(*(volatile word *)(SMC_BASE_ADDRESS+((r)<<0))=SMC_LEON_SWAP16(d))
-#define	SMC_outw_nosw(d,r)	(*(volatile word *)(SMC_BASE_ADDRESS+((r)<<0))=(d))
-#define	SMC_outb(d,r)	do{	word __d = (byte)(d);  \
-				word __w = SMC_inw((r)&~1);  \
+#define	SMC_outl(a,d,r)	(*(volatile dword *)((a)->iobase+((r)<<0))=SMC_LEON_SWAP32(d))
+#define	SMC_outl_nosw(a,d,r)	(*(volatile dword *)((a)->iobase+((r)<<0))=(d))
+#define	SMC_outw(a,d,r)	(*(volatile word *)((a)->iobase+((r)<<0))=SMC_LEON_SWAP16(d))
+#define	SMC_outw_nosw(a,d,r)	(*(volatile word *)((a)->iobase+((r)<<0))=(d))
+#define	SMC_outb(a,d,r)	do{	word __d = (byte)(d);  \
+				word __w = SMC_inw((a),(r)&~1);  \
 				__w &= ((r)&1) ? 0x00FF : 0xFF00;  \
 				__w |= ((r)&1) ? __d<<8 : __d;  \
-				SMC_outw(__w,(r)&~1);  \
+				SMC_outw((a),__w,(r)&~1);  \
 			}while(0)
-#define SMC_outsl(r,b,l)	do{	int __i; \
+#define SMC_outsl(a,r,b,l)	do{	int __i; \
 					dword *__b2; \
 					__b2 = (dword *) b; \
 					for (__i = 0; __i < l; __i++) { \
-					    SMC_outl_nosw( *(__b2 + __i), r); \
+					    SMC_outl_nosw((a), *(__b2 + __i), r); \
 					} \
 				}while(0)
-#define SMC_outsw(r,b,l)	do{	int __i; \
+#define SMC_outsw(a,r,b,l)	do{	int __i; \
 					word *__b2; \
 					__b2 = (word *) b; \
 					for (__i = 0; __i < l; __i++) { \
-					    SMC_outw_nosw( *(__b2 + __i), r); \
+					    SMC_outw_nosw((a), *(__b2 + __i), r); \
 					} \
 				}while(0)
-#define SMC_insl(r,b,l)		do{	int __i ;  \
+#define SMC_insl(a,r,b,l)	do{	int __i ;  \
 					dword *__b2;  \
 					__b2 = (dword *) b;  \
 					for (__i = 0; __i < l; __i++) {  \
-					  *(__b2 + __i) = SMC_inl_nosw(r);  \
+					  *(__b2 + __i) = SMC_inl_nosw((a),(r));  \
 					};  \
 				}while(0)
 
-#define SMC_insw(r,b,l)		do{	int __i ;  \
+#define SMC_insw(a,r,b,l)		do{	int __i ;  \
 					word *__b2;  \
 					__b2 = (word *) b;  \
 					for (__i = 0; __i < l; __i++) {  \
-					  *(__b2 + __i) = SMC_inw_nosw(r);  \
+					  *(__b2 + __i) = SMC_inw_nosw((a),(r));  \
 					};  \
 				}while(0)
 
-#define SMC_insb(r,b,l)		do{	int __i ;  \
+#define SMC_insb(a,r,b,l)		do{	int __i ;  \
 					byte *__b2;  \
 					__b2 = (byte *) b;  \
 					for (__i = 0; __i < l; __i++) {  \
-					  *(__b2 + __i) = SMC_inb(r);  \
+					  *(__b2 + __i) = SMC_inb((a),(r));  \
 					};  \
 				}while(0)
 
@@ -253,48 +257,48 @@
  */
 
 #ifdef CONFIG_ADNPESC1
-#define	SMC_inw(r)	(*((volatile word *)(SMC_BASE_ADDRESS+((r)<<1))))
+#define	SMC_inw(a,r)	(*((volatile word *)((a)->iobase+((r)<<1))))
 #elif CONFIG_BLACKFIN
-#define	SMC_inw(r)	({ word __v = (*((volatile word *)(SMC_BASE_ADDRESS+(r)))); SSYNC(); __v;})
+#define	SMC_inw(a,r)	({ word __v = (*((volatile word *)((a)->iobase+(r)))); SSYNC(); __v;})
 #else
-#define	SMC_inw(r)	(*((volatile word *)(SMC_BASE_ADDRESS+(r))))
+#define	SMC_inw(a,r)	(*((volatile word *)((a)->iobase+(r))))
 #endif
-#define  SMC_inb(r)	(((r)&1) ? SMC_inw((r)&~1)>>8 : SMC_inw(r)&0xFF)
+#define  SMC_inb(a,r)	(((r)&1) ? SMC_inw((a),(r)&~1)>>8 : SMC_inw((a),(r)&0xFF))
 
 #ifdef CONFIG_ADNPESC1
-#define	SMC_outw(d,r)	(*((volatile word *)(SMC_BASE_ADDRESS+((r)<<1))) = d)
+#define	SMC_outw(a,d,r)	(*((volatile word *)((a)->iobase+((r)<<1))) = d)
 #elif CONFIG_BLACKFIN
-#define	SMC_outw(d,r)	{(*((volatile word *)(SMC_BASE_ADDRESS+(r))) = d); SSYNC();}
+#define	SMC_outw(a,d,r)	{(*((volatile word *)((a)->iobase+(r))) = d); SSYNC();}
 #else
-#define	SMC_outw(d,r)	(*((volatile word *)(SMC_BASE_ADDRESS+(r))) = d)
+#define	SMC_outw(a,d,r)	(*((volatile word *)((a)->iobase+(r))) = d)
 #endif
-#define	SMC_outb(d,r)	({	word __d = (byte)(d);  \
-				word __w = SMC_inw((r)&~1);  \
+#define	SMC_outb(a,d,r)	({	word __d = (byte)(d);  \
+				word __w = SMC_inw((a),(r)&~1);  \
 				__w &= ((r)&1) ? 0x00FF : 0xFF00;  \
 				__w |= ((r)&1) ? __d<<8 : __d;  \
-				SMC_outw(__w,(r)&~1);  \
+				SMC_outw((a),__w,(r)&~1);  \
 			})
 #if 0
-#define	SMC_outsw(r,b,l)	outsw(SMC_BASE_ADDRESS+(r), (b), (l))
+#define	SMC_outsw(a,r,b,l)	outsw((a)->iobase+(r), (b), (l))
 #else
-#define SMC_outsw(r,b,l)	({	int __i; \
+#define SMC_outsw(a,r,b,l)	({	int __i; \
 					word *__b2; \
 					__b2 = (word *) b; \
 					for (__i = 0; __i < l; __i++) { \
-					    SMC_outw( *(__b2 + __i), r); \
+					    SMC_outw((a), *(__b2 + __i), r); \
 					} \
 				})
 #endif
 
 #if 0
-#define	SMC_insw(r,b,l)	insw(SMC_BASE_ADDRESS+(r), (b), (l))
+#define	SMC_insw(a,r,b,l)	insw((a)->iobase+(r), (b), (l))
 #else
-#define SMC_insw(r,b,l)	({	int __i ;  \
+#define SMC_insw(a,r,b,l)	({	int __i ;  \
 					word *__b2;  \
 					__b2 = (word *) b;  \
 					for (__i = 0; __i < l; __i++) {  \
-					  *(__b2 + __i) = SMC_inw(r);  \
-					  SMC_inw(0);  \
+					  *(__b2 + __i) = SMC_inw((a),(r));  \
+					  SMC_inw((a),0);  \
 					};  \
 				})
 #endif
@@ -304,30 +308,30 @@
 #if defined(CONFIG_SMC_USE_32_BIT)
 
 #ifdef CONFIG_XSENGINE
-#define	SMC_inl(r)	(*((volatile dword *)(SMC_BASE_ADDRESS+(r<<1))))
+#define	SMC_inl(a,r)	(*((volatile dword *)((a)->iobase+(r<<1))))
 #else
-#define	SMC_inl(r)	(*((volatile dword *)(SMC_BASE_ADDRESS+(r))))
+#define	SMC_inl(a,r)	(*((volatile dword *)((a)->iobase+(r))))
 #endif
 
-#define SMC_insl(r,b,l)	({	int __i ;  \
+#define SMC_insl(a,r,b,l)	({	int __i ;  \
 					dword *__b2;  \
 					__b2 = (dword *) b;  \
 					for (__i = 0; __i < l; __i++) {  \
-					  *(__b2 + __i) = SMC_inl(r);  \
-					  SMC_inl(0);  \
+					  *(__b2 + __i) = SMC_inl((a),(r));  \
+					  SMC_inl((a),0);  \
 					};  \
 				})
 
 #ifdef CONFIG_XSENGINE
-#define	SMC_outl(d,r)	(*((volatile dword *)(SMC_BASE_ADDRESS+(r<<1))) = d)
+#define	SMC_outl(a,d,r)	(*((volatile dword *)((a)->iobase+(r<<1))) = d)
 #else
-#define	SMC_outl(d,r)	(*((volatile dword *)(SMC_BASE_ADDRESS+(r))) = d)
+#define	SMC_outl(a,d,r)	(*((volatile dword *)((a)->iobase+(r))) = d)
 #endif
-#define SMC_outsl(r,b,l)	({	int __i; \
+#define SMC_outsl(a,r,b,l)	({	int __i; \
 					dword *__b2; \
 					__b2 = (dword *) b; \
 					for (__i = 0; __i < l; __i++) { \
-					    SMC_outl( *(__b2 + __i), r); \
+					    SMC_outl((a), *(__b2 + __i), r); \
 					} \
 				})
 
@@ -752,25 +756,25 @@
 
 /* select a register bank, 0 to 3  */
 
-#define SMC_SELECT_BANK(x)  { SMC_outw( x, BANK_SELECT ); }
+#define SMC_SELECT_BANK(a,x)  { SMC_outw((a), (x), BANK_SELECT ); }
 
 /* this enables an interrupt in the interrupt mask register */
-#define SMC_ENABLE_INT(x) {\
+#define SMC_ENABLE_INT(a,x) {\
 		unsigned char mask;\
-		SMC_SELECT_BANK(2);\
-		mask = SMC_inb( IM_REG );\
+		SMC_SELECT_BANK((a),2);\
+		mask = SMC_inb((a), IM_REG );\
 		mask |= (x);\
-		SMC_outb( mask, IM_REG ); \
+		SMC_outb( (a), mask, IM_REG ); \
 }
 
 /* this disables an interrupt from the interrupt mask register */
 
-#define SMC_DISABLE_INT(x) {\
+#define SMC_DISABLE_INT(a,x) {\
 		unsigned char mask;\
 		SMC_SELECT_BANK(2);\
-		mask = SMC_inb( IM_REG );\
+		mask = SMC_inb( (a), IM_REG );\
 		mask &= ~(x);\
-		SMC_outb( mask, IM_REG ); \
+		SMC_outb( (a), mask, IM_REG ); \
 }
 
 /*----------------------------------------------------------------------
diff --git a/examples/standalone/smc91111_eeprom.c b/examples/standalone/smc91111_eeprom.c
index 39e5306..89afc87 100644
--- a/examples/standalone/smc91111_eeprom.c
+++ b/examples/standalone/smc91111_eeprom.c
@@ -29,9 +29,11 @@
 
 #include <common.h>
 #include <exports.h>
+/* the smc91111.h gets base addr through eth_device' iobase */
+struct eth_device { unsigned long iobase; };
 #include "../drivers/net/smc91111.h"
 
-#ifdef CONFIG_DRIVER_SMC91111
+#ifdef CONFIG_SMC91111
 
 #ifndef SMC91111_EEPROM_INIT
 # define SMC91111_EEPROM_INIT()
@@ -42,19 +44,23 @@
 #define MAC		0x2
 #define UNKNOWN		0x4
 
-void dump_reg (void);
-void dump_eeprom (void);
-int write_eeprom_reg (int, int);
-void copy_from_eeprom (void);
-void print_MAC (void);
-int read_eeprom_reg (int);
-void print_macaddr (void);
+void dump_reg (struct eth_device *dev);
+void dump_eeprom (struct eth_device *dev);
+int write_eeprom_reg (struct eth_device *dev, int value, int reg);
+void copy_from_eeprom (struct eth_device *dev);
+void print_MAC (struct eth_device *dev);
+int read_eeprom_reg (struct eth_device *dev, int reg);
+void print_macaddr (struct eth_device *dev);
 
 int smc91111_eeprom (int argc, char *argv[])
 {
 	int c, i, j, done, line, reg, value, start, what;
 	char input[50];
 
+	struct eth_device dev = {
+		.iobase = CONFIG_SMC91111_BASE
+	};
+
 	/* Print the ABI version */
 	app_startup (argv);
 	if (XF_VERSION != (int) get_version ()) {
@@ -67,7 +73,7 @@
 
 	SMC91111_EEPROM_INIT();
 
-	if ((SMC_inw (BANK_SELECT) & 0xFF00) != 0x3300) {
+	if ((SMC_inw (&dev, BANK_SELECT) & 0xFF00) != 0x3300) {
 		printf ("Can't find SMSC91111\n");
 		return (0);
 	}
@@ -211,12 +217,12 @@
 			switch (what) {
 			case 1:
 				printf ("Writing EEPROM register %02x with %04x\n", reg, value);
-				write_eeprom_reg (value, reg);
+				write_eeprom_reg (&dev, value, reg);
 				break;
 			case 2:
 				printf ("Writing MAC register bank %i, reg %02x with %04x\n", reg >> 4, reg & 0xE, value);
-				SMC_SELECT_BANK (reg >> 4);
-				SMC_outw (value, reg & 0xE);
+				SMC_SELECT_BANK (&dev, reg >> 4);
+				SMC_outw (&dev, value, reg & 0xE);
 				break;
 			default:
 				printf ("Wrong\n");
@@ -224,16 +230,16 @@
 			}
 			break;
 		case ('D'):
-			dump_eeprom ();
+			dump_eeprom (&dev);
 			break;
 		case ('M'):
-			dump_reg ();
+			dump_reg (&dev);
 			break;
 		case ('C'):
-			copy_from_eeprom ();
+			copy_from_eeprom (&dev);
 			break;
 		case ('P'):
-			print_macaddr ();
+			print_macaddr (&dev);
 			break;
 		default:
 			break;
@@ -244,15 +250,15 @@
 	return (0);
 }
 
-void copy_from_eeprom (void)
+void copy_from_eeprom (struct eth_device *dev)
 {
 	int i;
 
-	SMC_SELECT_BANK (1);
-	SMC_outw ((SMC_inw (CTL_REG) & !CTL_EEPROM_SELECT) | CTL_RELOAD,
-		  CTL_REG);
+	SMC_SELECT_BANK (dev, 1);
+	SMC_outw (dev, (SMC_inw (dev, CTL_REG) & !CTL_EEPROM_SELECT) |
+		CTL_RELOAD, CTL_REG);
 	i = 100;
-	while ((SMC_inw (CTL_REG) & CTL_RELOAD) && --i)
+	while ((SMC_inw (dev, CTL_REG) & CTL_RELOAD) && --i)
 		udelay (100);
 	if (i == 0) {
 		printf ("Timeout Refreshing EEPROM registers\n");
@@ -262,21 +268,21 @@
 
 }
 
-void print_macaddr (void)
+void print_macaddr (struct eth_device *dev)
 {
 	int i, j, k, mac[6];
 
 	printf ("Current MAC Address in SMSC91111 ");
-	SMC_SELECT_BANK (1);
+	SMC_SELECT_BANK (dev, 1);
 	for (i = 0; i < 5; i++) {
-		printf ("%02x:", SMC_inb (ADDR0_REG + i));
+		printf ("%02x:", SMC_inb (dev, ADDR0_REG + i));
 	}
 
-	printf ("%02x\n", SMC_inb (ADDR0_REG + 5));
+	printf ("%02x\n", SMC_inb (dev, ADDR0_REG + 5));
 
 	i = 0;
 	for (j = 0x20; j < 0x23; j++) {
-		k = read_eeprom_reg (j);
+		k = read_eeprom_reg (dev, j);
 		mac[i] = k & 0xFF;
 		i++;
 		mac[i] = k >> 8;
@@ -289,7 +295,7 @@
 	printf ("%02x\n", mac[5]);
 
 }
-void dump_eeprom (void)
+void dump_eeprom (struct eth_device *dev)
 {
 	int j, k;
 
@@ -307,7 +313,8 @@
 		if ((k == 2) || (k == 3))
 			printf ("       ");
 		for (j = 0; j < 0x20; j += 4) {
-			printf ("%02x:%04x ", j + k, read_eeprom_reg (j + k));
+			printf ("%02x:%04x ", j + k,
+				read_eeprom_reg (dev, j + k));
 		}
 		printf ("\n");
 	}
@@ -315,46 +322,47 @@
 	for (j = 0x20; j < 0x40; j++) {
 		if ((j & 0x07) == 0)
 			printf ("\n");
-		printf ("%02x:%04x ", j, read_eeprom_reg (j));
+		printf ("%02x:%04x ", j, read_eeprom_reg (dev, j));
 	}
 	printf ("\n");
 
 }
 
-int read_eeprom_reg (int reg)
+int read_eeprom_reg (struct eth_device *dev, int reg)
 {
 	int timeout;
 
-	SMC_SELECT_BANK (2);
-	SMC_outw (reg, PTR_REG);
+	SMC_SELECT_BANK (dev, 2);
+	SMC_outw (dev, reg, PTR_REG);
 
-	SMC_SELECT_BANK (1);
-	SMC_outw (SMC_inw (CTL_REG) | CTL_EEPROM_SELECT | CTL_RELOAD,
-		  CTL_REG);
+	SMC_SELECT_BANK (dev, 1);
+	SMC_outw (dev, SMC_inw (dev, CTL_REG) | CTL_EEPROM_SELECT |
+		CTL_RELOAD, CTL_REG);
 	timeout = 100;
-	while ((SMC_inw (CTL_REG) & CTL_RELOAD) && --timeout)
+	while ((SMC_inw (dev, CTL_REG) & CTL_RELOAD) && --timeout)
 		udelay (100);
 	if (timeout == 0) {
 		printf ("Timeout Reading EEPROM register %02x\n", reg);
 		return 0;
 	}
 
-	return SMC_inw (GP_REG);
+	return SMC_inw (dev, GP_REG);
 
 }
 
-int write_eeprom_reg (int value, int reg)
+int write_eeprom_reg (struct eth_device *dev, int value, int reg)
 {
 	int timeout;
 
-	SMC_SELECT_BANK (2);
-	SMC_outw (reg, PTR_REG);
+	SMC_SELECT_BANK (dev, 2);
+	SMC_outw (dev, reg, PTR_REG);
 
-	SMC_SELECT_BANK (1);
-	SMC_outw (value, GP_REG);
-	SMC_outw (SMC_inw (CTL_REG) | CTL_EEPROM_SELECT | CTL_STORE, CTL_REG);
+	SMC_SELECT_BANK (dev, 1);
+	SMC_outw (dev, value, GP_REG);
+	SMC_outw (dev, SMC_inw (dev, CTL_REG) | CTL_EEPROM_SELECT |
+		CTL_STORE, CTL_REG);
 	timeout = 100;
-	while ((SMC_inw (CTL_REG) & CTL_STORE) && --timeout)
+	while ((SMC_inw (dev, CTL_REG) & CTL_STORE) && --timeout)
 		udelay (100);
 	if (timeout == 0) {
 		printf ("Timeout Writing EEPROM register %02x\n", reg);
@@ -365,7 +373,7 @@
 
 }
 
-void dump_reg (void)
+void dump_reg (struct eth_device *dev)
 {
 	int i, j;
 
@@ -377,8 +385,8 @@
 	for (i = 0; i < 0xF; i += 2) {
 		printf ("%02x  ", i);
 		for (j = 0; j < 4; j++) {
-			SMC_SELECT_BANK (j);
-			printf ("%04x  ", SMC_inw (i));
+			SMC_SELECT_BANK (dev, j);
+			printf ("%04x  ", SMC_inw (dev, i));
 		}
 		printf ("\n");
 	}
diff --git a/include/configs/EP1C20.h b/include/configs/EP1C20.h
index 8941e4d..61d8e20 100644
--- a/include/configs/EP1C20.h
+++ b/include/configs/EP1C20.h
@@ -151,7 +151,8 @@
  * cache bypass so there's no need to monkey with inx/outx macros.
  *----------------------------------------------------------------------*/
 #define CONFIG_SMC91111_BASE	0x82110300	/* Base addr (bypass)	*/
-#define CONFIG_DRIVER_SMC91111			/* Using SMC91c111	*/
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111			/* Using SMC91c111	*/
 #undef	CONFIG_SMC91111_EXT_PHY			/* Internal PHY		*/
 #define CONFIG_SMC_USE_32_BIT			/* 32-bit interface	*/
 
diff --git a/include/configs/EP1S10.h b/include/configs/EP1S10.h
index 53bd0d8..41e64e6 100644
--- a/include/configs/EP1S10.h
+++ b/include/configs/EP1S10.h
@@ -145,7 +145,8 @@
  * cache bypass so there's no need to monkey with inx/outx macros.
  *----------------------------------------------------------------------*/
 #define CONFIG_SMC91111_BASE	0x82110300	/* Base addr (bypass)	*/
-#define CONFIG_DRIVER_SMC91111			/* Using SMC91c111	*/
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111			/* Using SMC91c111	*/
 #undef	CONFIG_SMC91111_EXT_PHY			/* Internal PHY		*/
 #define CONFIG_SMC_USE_32_BIT			/* 32-bit interface	*/
 
diff --git a/include/configs/EP1S40.h b/include/configs/EP1S40.h
index 9e9a8a4..5b332e4 100644
--- a/include/configs/EP1S40.h
+++ b/include/configs/EP1S40.h
@@ -145,7 +145,8 @@
  * cache bypass so there's no need to monkey with inx/outx macros.
  *----------------------------------------------------------------------*/
 #define CONFIG_SMC91111_BASE	0x82110300	/* Base addr (bypass)	*/
-#define CONFIG_DRIVER_SMC91111			/* Using SMC91c111	*/
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111			/* Using SMC91c111	*/
 #undef	CONFIG_SMC91111_EXT_PHY			/* Internal PHY		*/
 #define CONFIG_SMC_USE_32_BIT			/* 32-bit interface	*/
 
diff --git a/include/configs/MigoR.h b/include/configs/MigoR.h
index 3853574..6083892 100644
--- a/include/configs/MigoR.h
+++ b/include/configs/MigoR.h
@@ -50,7 +50,8 @@
 #undef  CONFIG_SHOW_BOOT_PROGRESS
 
 /* SMC9111 */
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC91111_BASE    (0xB0000000)
 
 /* MEMORY */
diff --git a/include/configs/PK1C20.h b/include/configs/PK1C20.h
index 522349f..cf6f7a9 100644
--- a/include/configs/PK1C20.h
+++ b/include/configs/PK1C20.h
@@ -151,7 +151,8 @@
  * cache bypass so there's no need to monkey with inx/outx macros.
  *----------------------------------------------------------------------*/
 #define CONFIG_SMC91111_BASE	0x82110300	/* Base addr (bypass)	*/
-#define CONFIG_DRIVER_SMC91111			/* Using SMC91c111	*/
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111			/* Using SMC91c111	*/
 #undef	CONFIG_SMC91111_EXT_PHY			/* Internal PHY		*/
 #define CONFIG_SMC_USE_32_BIT			/* 32-bit interface	*/
 
diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h
index 8342ec7..c80ddca 100644
--- a/include/configs/bf533-ezkit.h
+++ b/include/configs/bf533-ezkit.h
@@ -65,12 +65,14 @@
  * Network Settings
  */
 #define ADI_CMDS_NETWORK	1
-#define CONFIG_DRIVER_SMC91111	1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111	1
 #define CONFIG_SMC91111_BASE	0x20310300
 #define SMC91111_EEPROM_INIT() \
 	do { \
-		*pFIO_DIR |= PF1; \
-		*pFIO_FLAG_S = PF1; \
+		bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF1 | PF0); \
+		bfin_write_FIO_FLAG_C(PF1); \
+		bfin_write_FIO_FLAG_S(PF0); \
 		SSYNC(); \
 	} while (0)
 #define CONFIG_HOSTNAME		bf533-ezkit
diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h
index 4be2a5c..0006b02 100644
--- a/include/configs/bf533-stamp.h
+++ b/include/configs/bf533-stamp.h
@@ -60,12 +60,14 @@
  * Network Settings
  */
 #define ADI_CMDS_NETWORK	1
-#define CONFIG_DRIVER_SMC91111	1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111	1
 #define CONFIG_SMC91111_BASE	0x20300300
 #define SMC91111_EEPROM_INIT() \
 	do { \
-		*pFIO_DIR |= PF1; \
-		*pFIO_FLAG_S = PF1; \
+		bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF1 | PF0); \
+		bfin_write_FIO_FLAG_C(PF1); \
+		bfin_write_FIO_FLAG_S(PF0); \
 		SSYNC(); \
 	} while (0)
 #define CONFIG_HOSTNAME		bf533-stamp
diff --git a/include/configs/bf538f-ezkit.h b/include/configs/bf538f-ezkit.h
index 535687f..c4d899d 100644
--- a/include/configs/bf538f-ezkit.h
+++ b/include/configs/bf538f-ezkit.h
@@ -60,7 +60,8 @@
  * Network Settings
  */
 #define ADI_CMDS_NETWORK	1
-#define CONFIG_DRIVER_SMC91111	1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111	1
 #define CONFIG_SMC91111_BASE	0x20310300
 #define CONFIG_HOSTNAME		bf538f-ezkit
 /* Uncomment next line to use fixed MAC address */
diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h
index 4779a97..a1fa80b 100644
--- a/include/configs/bf561-ezkit.h
+++ b/include/configs/bf561-ezkit.h
@@ -60,7 +60,8 @@
  * Network Settings
  */
 #define ADI_CMDS_NETWORK	1
-#define CONFIG_DRIVER_SMC91111	1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111	1
 #define CONFIG_SMC91111_BASE	0x2C010300
 #define CONFIG_SMC_USE_32_BIT	1
 #define CONFIG_HOSTNAME		bf561-ezkit
diff --git a/include/configs/blackstamp.h b/include/configs/blackstamp.h
index 887f3fb..aa33933 100644
--- a/include/configs/blackstamp.h
+++ b/include/configs/blackstamp.h
@@ -30,7 +30,8 @@
 /*
  * Board settings
  */
-#define CONFIG_DRIVER_SMC91111	1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111	1
 #define CONFIG_SMC91111_BASE	0x20300300
 
 /* FLASH/ETHERNET uses the same address range
@@ -69,7 +70,7 @@
  * Network settings
  */
 
-#ifdef CONFIG_DRIVER_SMC91111
+#ifdef CONFIG_SMC91111
 #define CONFIG_IPADDR		192.168.0.15
 #define CONFIG_NETMASK		255.255.255.0
 #define CONFIG_GATEWAYIP	192.168.0.1
@@ -108,7 +109,7 @@
 
 #include <config_cmd_default.h>
 
-#ifdef CONFIG_DRIVER_SMC91111
+#ifdef CONFIG_SMC91111
 # define CONFIG_CMD_DHCP
 # define CONFIG_CMD_PING
 #else
diff --git a/include/configs/cerf250.h b/include/configs/cerf250.h
index b924758..477b94a 100644
--- a/include/configs/cerf250.h
+++ b/include/configs/cerf250.h
@@ -53,7 +53,8 @@
 /*
  * Hardware drivers
  */
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC91111_BASE 0x04000300
 #define CONFIG_SMC_USE_32_BIT
 
diff --git a/include/configs/cm-bf533.h b/include/configs/cm-bf533.h
index ea548e9..06eb288 100644
--- a/include/configs/cm-bf533.h
+++ b/include/configs/cm-bf533.h
@@ -60,7 +60,8 @@
  * Network Settings
  */
 #define ADI_CMDS_NETWORK	1
-#define CONFIG_DRIVER_SMC91111	1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111	1
 #define CONFIG_SMC91111_BASE	0x20200300
 #define CONFIG_HOSTNAME		cm-bf533
 /* Uncomment next line to use fixed MAC address */
diff --git a/include/configs/cm-bf561.h b/include/configs/cm-bf561.h
index 59dc8d2..4a77435 100644
--- a/include/configs/cm-bf561.h
+++ b/include/configs/cm-bf561.h
@@ -61,7 +61,8 @@
  */
 #define ADI_CMDS_NETWORK	1
 /* The next 2 lines are for use with DEV-BF5xx */
-#define CONFIG_DRIVER_SMC91111	1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111	1
 #define CONFIG_SMC91111_BASE	0x28000300
 /* The next 3 lines are for use with EXT-BF5xx-USB-ETH2 */
 /* #define CONFIG_DRIVER_SMC911X 1 */
diff --git a/include/configs/cradle.h b/include/configs/cradle.h
index b150c22..200b61e 100644
--- a/include/configs/cradle.h
+++ b/include/configs/cradle.h
@@ -49,7 +49,8 @@
 /*
  * Hardware drivers
  */
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC91111_BASE 0x10000300
 #define CONFIG_SMC91111_EXT_PHY
 #define CONFIG_SMC_USE_32_BIT
diff --git a/include/configs/dnp1110.h b/include/configs/dnp1110.h
index b6cfc67..e48e20f 100644
--- a/include/configs/dnp1110.h
+++ b/include/configs/dnp1110.h
@@ -54,7 +54,8 @@
 /*
  * Hardware drivers
  */
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC91111_BASE 0x20000300
 
 
diff --git a/include/configs/gr_cpci_ax2000.h b/include/configs/gr_cpci_ax2000.h
index bbe635b..d188439 100644
--- a/include/configs/gr_cpci_ax2000.h
+++ b/include/configs/gr_cpci_ax2000.h
@@ -292,7 +292,8 @@
 /*
  * Ethernet configuration uses on board SMC91C111
  */
-#define CONFIG_DRIVER_SMC91111          1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111          1
 #define CONFIG_SMC91111_BASE		0x20000300	/* chip select 3         */
 #define CONFIG_SMC_USE_32_BIT		1	/* 32 bit bus  */
 #undef  CONFIG_SMC_91111_EXT_PHY	/* we use internal phy   */
diff --git a/include/configs/gr_ep2s60.h b/include/configs/gr_ep2s60.h
index 7b0a08f..3a568ff 100644
--- a/include/configs/gr_ep2s60.h
+++ b/include/configs/gr_ep2s60.h
@@ -267,7 +267,8 @@
 #ifndef USE_GRETH
 
 /* USE SMC91C111 MAC */
-#define CONFIG_DRIVER_SMC91111          1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111          1
 #define CONFIG_SMC91111_BASE		0x20000300	/* chip select 3         */
 #define CONFIG_SMC_USE_32_BIT		1	/* 32 bit bus  */
 #undef  CONFIG_SMC_91111_EXT_PHY	/* we use internal phy   */
diff --git a/include/configs/innokom.h b/include/configs/innokom.h
index ed03ad3..9cb0d42 100644
--- a/include/configs/innokom.h
+++ b/include/configs/innokom.h
@@ -157,7 +157,8 @@
 /*
  * SMSC91C111 Network Card
  */
-#define CONFIG_DRIVER_SMC91111		1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111		1
 #define CONFIG_SMC91111_BASE		0x14000000 /* chip select 5         */
 #undef  CONFIG_SMC_USE_32_BIT		           /* 16 bit bus access     */
 #undef  CONFIG_SMC_91111_EXT_PHY		   /* we use internal phy   */
diff --git a/include/configs/integratorcp.h b/include/configs/integratorcp.h
index e38d569..caafc93 100644
--- a/include/configs/integratorcp.h
+++ b/include/configs/integratorcp.h
@@ -53,7 +53,8 @@
 /*
  * Hardware drivers
  */
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC_USE_32_BIT
 #define CONFIG_SMC91111_BASE    0xC8000000
 #undef CONFIG_SMC91111_EXT_PHY
diff --git a/include/configs/logodl.h b/include/configs/logodl.h
index 5b903f0..0535ee1 100644
--- a/include/configs/logodl.h
+++ b/include/configs/logodl.h
@@ -133,7 +133,8 @@
  * SMSC91C111 Network Card
  */
 #if 0
-#define CONFIG_DRIVER_SMC91111		1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111		1
 #define CONFIG_SMC91111_BASE		0x10000000 /* chip select 4         */
 #undef  CONFIG_SMC_USE_32_BIT		           /* 16 bit bus access     */
 #undef  CONFIG_SMC_91111_EXT_PHY		   /* we use internal phy   */
diff --git a/include/configs/lpd7a400-10.h b/include/configs/lpd7a400-10.h
index 6145c37..5f57c3a 100644
--- a/include/configs/lpd7a400-10.h
+++ b/include/configs/lpd7a400-10.h
@@ -72,7 +72,8 @@
  * Default IO base of chip is 0x300, Card Engine has this address lines
  * (LAN chip) tied to Vcc, so we just care about the chip select
  */
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC91111_BASE	(0x70000000)
 #undef CONFIG_SMC_USE_32_BIT
 #define CONFIG_SMC_USE_IOFUNCS
diff --git a/include/configs/lpd7a404-10.h b/include/configs/lpd7a404-10.h
index ce23f3d..9074e28 100644
--- a/include/configs/lpd7a404-10.h
+++ b/include/configs/lpd7a404-10.h
@@ -72,7 +72,8 @@
  * Default IO base of chip is 0x300, Card Engine has this address lines
  * (LAN chip) tied to Vcc, so we just care about the chip select
  */
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC91111_BASE	(0x70000000)
 #undef CONFIG_SMC_USE_32_BIT
 #define CONFIG_SMC_USE_IOFUNCS
diff --git a/include/configs/ms7722se.h b/include/configs/ms7722se.h
index 6755af3..0251428 100644
--- a/include/configs/ms7722se.h
+++ b/include/configs/ms7722se.h
@@ -48,7 +48,8 @@
 #undef  CONFIG_SHOW_BOOT_PROGRESS
 
 /* SMC9111 */
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC91111_BASE    (0xB8000000)
 
 /* MEMORY */
diff --git a/include/configs/netstar.h b/include/configs/netstar.h
index f0b4207..7bddf24 100644
--- a/include/configs/netstar.h
+++ b/include/configs/netstar.h
@@ -93,7 +93,8 @@
 #define CONFIG_SYS_NS16550_CLK		(CONFIG_XTAL_FREQ)	/* can be 12M/32Khz or 48Mhz  */
 #define CONFIG_SYS_NS16550_COM1		OMAP1510_UART1_BASE	/* uart1 */
 
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC91111_BASE		0x04000300
 
 #define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
diff --git a/include/configs/nhk8815.h b/include/configs/nhk8815.h
index 027e8e1..a00c2fb 100644
--- a/include/configs/nhk8815.h
+++ b/include/configs/nhk8815.h
@@ -132,7 +132,8 @@
 #define __io(a)			((void __iomem *)(PCI_IO_VADDR + (a)))
 #define __mem_isa(a)		((a) + PCI_MEMORY_VADDR)
 
-#define CONFIG_DRIVER_SMC91111	/* Using SMC91c111*/
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111	/* Using SMC91c111*/
 #define CONFIG_SMC91111_BASE	0x34000300
 #undef  CONFIG_SMC91111_EXT_PHY	/* Internal PHY */
 #define CONFIG_SMC_USE_32_BIT
diff --git a/include/configs/pxa255_idp.h b/include/configs/pxa255_idp.h
index 2cae8ca..6c1defc 100644
--- a/include/configs/pxa255_idp.h
+++ b/include/configs/pxa255_idp.h
@@ -87,7 +87,8 @@
 /*
  * Hardware drivers
  */
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC91111_BASE	(PXA_CS5_PHYS + IDP_CS5_ETH_OFFSET + 0x300)
 #define CONFIG_SMC_USE_32_BIT	1
 /* #define CONFIG_SMC_USE_IOFUNCS */
diff --git a/include/configs/versatile.h b/include/configs/versatile.h
index a9b70cc..4273b84 100644
--- a/include/configs/versatile.h
+++ b/include/configs/versatile.h
@@ -82,7 +82,8 @@
  * Hardware drivers
  */
 
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC_USE_32_BIT
 #define CONFIG_SMC91111_BASE	0x10010000
 #undef CONFIG_SMC91111_EXT_PHY
diff --git a/include/configs/voiceblue.h b/include/configs/voiceblue.h
index c9c3132..0dde65d 100644
--- a/include/configs/voiceblue.h
+++ b/include/configs/voiceblue.h
@@ -94,7 +94,8 @@
 /*
  * Hardware drivers
  */
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC91111_BASE	0x08000300
 
 #define CONFIG_HARD_I2C
diff --git a/include/configs/xaeniax.h b/include/configs/xaeniax.h
index 83883f6..1329f0f 100644
--- a/include/configs/xaeniax.h
+++ b/include/configs/xaeniax.h
@@ -196,7 +196,8 @@
 /*
  * SMSC91C111 Network Card
  */
-#define CONFIG_DRIVER_SMC91111		1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111		1
 #define CONFIG_SMC91111_BASE		0x10000300  /* chip select 3         */
 #define CONFIG_SMC_USE_32_BIT		1          /* 32 bit bus  */
 #undef  CONFIG_SMC_91111_EXT_PHY		   /* we use internal phy   */
diff --git a/include/configs/xm250.h b/include/configs/xm250.h
index f18701a..cd56ce7 100644
--- a/include/configs/xm250.h
+++ b/include/configs/xm250.h
@@ -50,7 +50,8 @@
 /*
  * Hardware drivers
  */
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC91111_BASE		0x04000300
 #undef	CONFIG_SMC91111_EXT_PHY
 #define CONFIG_SMC_USE_32_BIT
diff --git a/include/configs/xsengine.h b/include/configs/xsengine.h
index 2697cca..f68461b 100644
--- a/include/configs/xsengine.h
+++ b/include/configs/xsengine.h
@@ -94,7 +94,8 @@
 #define CONFIG_SYS_GBL_DATA_SIZE		128		/* size in bytes reserved for initial data */
 
 /* Hardware drivers */
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111
 #define CONFIG_SMC91111_BASE		0x04000300
 #define CONFIG_SMC_USE_32_BIT		1
 
diff --git a/include/configs/zylonite.h b/include/configs/zylonite.h
index 86b6ea1..36c341e 100644
--- a/include/configs/zylonite.h
+++ b/include/configs/zylonite.h
@@ -62,7 +62,7 @@
 
 #undef TURN_ON_ETHERNET
 #ifdef TURN_ON_ETHERNET
-# define CONFIG_DRIVER_SMC91111 1
+# define CONFIG_SMC91111 1
 # define CONFIG_SMC91111_BASE   0x14000300
 # define CONFIG_SMC91111_EXT_PHY
 # define CONFIG_SMC_USE_32_BIT
diff --git a/include/netdev.h b/include/netdev.h
index a50ec67..a91368e 100644
--- a/include/netdev.h
+++ b/include/netdev.h
@@ -75,6 +75,7 @@
 int scc_initialize(bd_t *bis);
 int skge_initialize(bd_t *bis);
 int smc911x_initialize(u8 dev_num, int base_addr);
+int smc91111_initialize(u8 dev_num, int base_addr);
 int tsi108_eth_initialize(bd_t *bis);
 int uec_initialize(int index);
 int uec_standard_init(bd_t *bis);