blob: 5ad2f7b89575c6c3cfdeb6a4ba9a12f1a052d82d [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2018-2019 NXP
*
*/
#include <common.h>
#include <spl.h>
#include <asm/io.h>
#include <errno.h>
#include <asm/io.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/arch/imx8mm_pins.h>
#include <asm/arch/sys_proto.h>
#include <power/pmic.h>
#include <power/bd71837.h>
#include <asm/arch/clock.h>
#include <asm/mach-imx/gpio.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <fsl_esdhc.h>
#include <mmc.h>
#include <asm/arch/ddr.h>
DECLARE_GLOBAL_DATA_PTR;
void spl_dram_init(void)
{
ddr_init(&dram_timing);
}
#define I2C_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PE)
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
struct i2c_pads_info i2c_pad_info1 = {
.scl = {
.i2c_mode = IMX8MM_PAD_I2C1_SCL_I2C1_SCL | PC,
.gpio_mode = IMX8MM_PAD_I2C1_SCL_GPIO5_IO14 | PC,
.gp = IMX_GPIO_NR(5, 14),
},
.sda = {
.i2c_mode = IMX8MM_PAD_I2C1_SDA_I2C1_SDA | PC,
.gpio_mode = IMX8MM_PAD_I2C1_SDA_GPIO5_IO15 | PC,
.gp = IMX_GPIO_NR(5, 15),
},
};
#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 18)
#define USDHC2_PWR_GPIO IMX_GPIO_NR(2, 19)
#define USDHC_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE |PAD_CTL_PE | \
PAD_CTL_FSEL2)
#define USDHC_GPIO_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE1)
static iomux_v3_cfg_t const usdhc3_pads[] = {
IMX8MM_PAD_NAND_WE_B_USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_NAND_WP_B_USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_NAND_DATA04_USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_NAND_DATA05_USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_NAND_DATA06_USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_NAND_DATA07_USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_NAND_RE_B_USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_NAND_CE2_B_USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_NAND_CE3_B_USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_NAND_CLE_USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
static iomux_v3_cfg_t const usdhc2_pads[] = {
IMX8MM_PAD_SD2_CLK_USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_SD2_CMD_USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_SD2_DATA0_USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_SD2_DATA1_USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_SD2_DATA2_USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_SD2_DATA3_USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
IMX8MM_PAD_SD2_RESET_B_GPIO2_IO19 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL),
};
/*
* The evk board uses DAT3 to detect CD card plugin,
* in u-boot we mux the pin to GPIO when doing board_mmc_getcd.
*/
static iomux_v3_cfg_t const usdhc2_cd_pad =
IMX8MM_PAD_SD2_DATA3_GPIO2_IO18 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL);
static iomux_v3_cfg_t const usdhc2_dat3_pad =
IMX8MM_PAD_SD2_DATA3_USDHC2_DATA3 |
MUX_PAD_CTRL(USDHC_PAD_CTRL);
static struct fsl_esdhc_cfg usdhc_cfg[2] = {
{USDHC2_BASE_ADDR, 0, 1},
{USDHC3_BASE_ADDR, 0, 1},
};
int board_mmc_init(bd_t *bis)
{
int i, ret;
/*
* According to the board_mmc_init() the following map is done:
* (U-Boot device node) (Physical Port)
* mmc0 USDHC1
* mmc1 USDHC2
*/
for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
switch (i) {
case 0:
init_clk_usdhc(1);
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
imx_iomux_v3_setup_multiple_pads(
usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
gpio_request(USDHC2_PWR_GPIO, "usdhc2_reset");
gpio_direction_output(USDHC2_PWR_GPIO, 0);
udelay(500);
gpio_direction_output(USDHC2_PWR_GPIO, 1);
break;
case 1:
init_clk_usdhc(2);
usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
imx_iomux_v3_setup_multiple_pads(
usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
break;
default:
printf("Warning: you configured more USDHC controllers"
"(%d) than supported by the board\n", i + 1);
return -EINVAL;
}
ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
if (ret)
return ret;
}
return 0;
}
int board_mmc_getcd(struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
int ret = 0;
switch (cfg->esdhc_base) {
case USDHC3_BASE_ADDR:
ret = 1;
break;
case USDHC2_BASE_ADDR:
imx_iomux_v3_setup_pad(usdhc2_cd_pad);
gpio_request(USDHC2_CD_GPIO, "usdhc2 cd");
gpio_direction_input(USDHC2_CD_GPIO);
/*
* Since it is the DAT3 pin, this pin is pulled to
* low voltage if no card
*/
ret = gpio_get_value(USDHC2_CD_GPIO);
imx_iomux_v3_setup_pad(usdhc2_dat3_pad);
return ret;
}
return 1;
}
#ifdef CONFIG_POWER
#define I2C_PMIC 0
int power_init_board(void)
{
struct pmic *p;
int ret;
ret = power_bd71837_init(I2C_PMIC);
if (ret)
printf("power init failed");
p = pmic_get("BD71837");
pmic_probe(p);
/* decrease RESET key long push time from the default 10s to 10ms */
pmic_reg_write(p, BD71837_PWRONCONFIG1, 0x0);
/* unlock the PMIC regs */
pmic_reg_write(p, BD71837_REGLOCK, 0x1);
/* increase VDD_SOC to typical value 0.85v before first DRAM access */
pmic_reg_write(p, BD71837_BUCK1_VOLT_RUN, 0x0f);
/* increase VDD_DRAM to 0.975v for 3Ghz DDR */
pmic_reg_write(p, BD71837_BUCK5_VOLT, 0x83);
#ifndef CONFIG_IMX8M_LPDDR4
/* increase NVCC_DRAM_1V2 to 1.2v for DDR4 */
pmic_reg_write(p, BD71837_BUCK8_VOLT, 0x28);
#endif
/* lock the PMIC regs */
pmic_reg_write(p, BD71837_REGLOCK, 0x11);
return 0;
}
#endif
void spl_board_init(void)
{
#ifndef CONFIG_SPL_USB_SDP_SUPPORT
/* Serial download mode */
if (is_usb_boot()) {
puts("Back to ROM, SDP\n");
restore_boot_params();
}
#endif
puts("Normal Boot\n");
}
#ifdef CONFIG_SPL_LOAD_FIT
int board_fit_config_name_match(const char *name)
{
/* Just empty function now - can't decide what to choose */
debug("%s: %s\n", __func__, name);
return 0;
}
#endif
void board_init_f(ulong dummy)
{
int ret;
/* Clear global data */
memset((void *)gd, 0, sizeof(gd_t));
arch_cpu_init();
board_early_init_f();
timer_init();
preloader_console_init();
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
ret = spl_init();
if (ret) {
debug("spl_init() failed: %d\n", ret);
hang();
}
enable_tzc380();
/* Adjust pmic voltage to 1.0V for 800M */
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
power_init_board();
/* DDR initialization */
spl_dram_init();
board_init_r(NULL, 0);
}