blob: f629c6a862f7a81b49606f6bea60188fa14a2cc9 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+ OR MIT
//
// Device Tree Source for UniPhier PXs3 SoC
//
// Copyright (C) 2017 Socionext Inc.
// Author: Masahiro Yamada <yamada.masahiro@socionext.com>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/gpio/uniphier-gpio.h>
/memreserve/ 0x80000000 0x02000000;
/ {
compatible = "socionext,uniphier-pxs3";
#address-cells = <2>;
#size-cells = <2>;
interrupt-parent = <&gic>;
cpus {
#address-cells = <2>;
#size-cells = <0>;
cpu-map {
cluster0 {
core0 {
cpu = <&cpu0>;
};
core1 {
cpu = <&cpu1>;
};
core2 {
cpu = <&cpu2>;
};
core3 {
cpu = <&cpu3>;
};
};
};
cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0 0x000>;
clocks = <&sys_clk 33>;
enable-method = "psci";
operating-points-v2 = <&cluster0_opp>;
};
cpu1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0 0x001>;
clocks = <&sys_clk 33>;
enable-method = "psci";
operating-points-v2 = <&cluster0_opp>;
};
cpu2: cpu@2 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0 0x002>;
clocks = <&sys_clk 33>;
enable-method = "psci";
operating-points-v2 = <&cluster0_opp>;
};
cpu3: cpu@3 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0 0x003>;
clocks = <&sys_clk 33>;
enable-method = "psci";
operating-points-v2 = <&cluster0_opp>;
};
};
cluster0_opp: opp-table {
compatible = "operating-points-v2";
opp-shared;
opp-250000000 {
opp-hz = /bits/ 64 <250000000>;
clock-latency-ns = <300>;
};
opp-325000000 {
opp-hz = /bits/ 64 <325000000>;
clock-latency-ns = <300>;
};
opp-500000000 {
opp-hz = /bits/ 64 <500000000>;
clock-latency-ns = <300>;
};
opp-650000000 {
opp-hz = /bits/ 64 <650000000>;
clock-latency-ns = <300>;
};
opp-666667000 {
opp-hz = /bits/ 64 <666667000>;
clock-latency-ns = <300>;
};
opp-866667000 {
opp-hz = /bits/ 64 <866667000>;
clock-latency-ns = <300>;
};
opp-1000000000 {
opp-hz = /bits/ 64 <1000000000>;
clock-latency-ns = <300>;
};
opp-1300000000 {
opp-hz = /bits/ 64 <1300000000>;
clock-latency-ns = <300>;
};
};
psci {
compatible = "arm,psci-1.0";
method = "smc";
};
clocks {
refclk: ref {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
};
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio UNIPHIER_GPIO_PORT(5, 7) GPIO_ACTIVE_LOW>;
};
timer {
compatible = "arm,armv8-timer";
interrupts = <1 13 4>,
<1 14 4>,
<1 11 4>,
<1 10 4>;
};
soc@0 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 0 0xffffffff>;
spi0: spi@54006000 {
compatible = "socionext,uniphier-scssi";
status = "disabled";
reg = <0x54006000 0x100>;
interrupts = <0 39 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi0>;
clocks = <&peri_clk 11>;
resets = <&peri_rst 11>;
};
spi1: spi@54006100 {
compatible = "socionext,uniphier-scssi";
status = "disabled";
reg = <0x54006100 0x100>;
interrupts = <0 216 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi1>;
clocks = <&peri_clk 11>;
resets = <&peri_rst 11>;
};
serial0: serial@54006800 {
compatible = "socionext,uniphier-uart";
status = "disabled";
reg = <0x54006800 0x40>;
interrupts = <0 33 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0>;
clocks = <&peri_clk 0>;
resets = <&peri_rst 0>;
};
serial1: serial@54006900 {
compatible = "socionext,uniphier-uart";
status = "disabled";
reg = <0x54006900 0x40>;
interrupts = <0 35 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
clocks = <&peri_clk 1>;
resets = <&peri_rst 1>;
};
serial2: serial@54006a00 {
compatible = "socionext,uniphier-uart";
status = "disabled";
reg = <0x54006a00 0x40>;
interrupts = <0 37 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
clocks = <&peri_clk 2>;
resets = <&peri_rst 2>;
};
serial3: serial@54006b00 {
compatible = "socionext,uniphier-uart";
status = "disabled";
reg = <0x54006b00 0x40>;
interrupts = <0 177 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
clocks = <&peri_clk 3>;
resets = <&peri_rst 3>;
};
gpio: gpio@55000000 {
compatible = "socionext,uniphier-gpio";
reg = <0x55000000 0x200>;
interrupt-parent = <&aidet>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&pinctrl 0 0 0>,
<&pinctrl 104 0 0>,
<&pinctrl 168 0 0>;
gpio-ranges-group-names = "gpio_range0",
"gpio_range1",
"gpio_range2";
ngpios = <286>;
socionext,interrupt-ranges = <0 48 16>, <16 154 5>,
<21 217 3>;
};
i2c0: i2c@58780000 {
compatible = "socionext,uniphier-fi2c";
status = "disabled";
reg = <0x58780000 0x80>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <0 41 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c0>;
clocks = <&peri_clk 4>;
resets = <&peri_rst 4>;
clock-frequency = <100000>;
};
i2c1: i2c@58781000 {
compatible = "socionext,uniphier-fi2c";
status = "disabled";
reg = <0x58781000 0x80>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <0 42 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
clocks = <&peri_clk 5>;
resets = <&peri_rst 5>;
clock-frequency = <100000>;
};
i2c2: i2c@58782000 {
compatible = "socionext,uniphier-fi2c";
status = "disabled";
reg = <0x58782000 0x80>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <0 43 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
clocks = <&peri_clk 6>;
resets = <&peri_rst 6>;
clock-frequency = <100000>;
};
i2c3: i2c@58783000 {
compatible = "socionext,uniphier-fi2c";
status = "disabled";
reg = <0x58783000 0x80>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <0 44 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
clocks = <&peri_clk 7>;
resets = <&peri_rst 7>;
clock-frequency = <100000>;
};
/* chip-internal connection for HDMI */
i2c6: i2c@58786000 {
compatible = "socionext,uniphier-fi2c";
reg = <0x58786000 0x80>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <0 26 4>;
clocks = <&peri_clk 10>;
resets = <&peri_rst 10>;
clock-frequency = <400000>;
};
system_bus: system-bus@58c00000 {
compatible = "socionext,uniphier-system-bus";
status = "disabled";
reg = <0x58c00000 0x400>;
#address-cells = <2>;
#size-cells = <1>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_system_bus>;
};
smpctrl@59801000 {
compatible = "socionext,uniphier-smpctrl";
reg = <0x59801000 0x400>;
};
sdctrl@59810000 {
compatible = "socionext,uniphier-pxs3-sdctrl",
"simple-mfd", "syscon";
reg = <0x59810000 0x400>;
sd_clk: clock {
compatible = "socionext,uniphier-pxs3-sd-clock";
#clock-cells = <1>;
};
sd_rst: reset {
compatible = "socionext,uniphier-pxs3-sd-reset";
#reset-cells = <1>;
};
};
perictrl@59820000 {
compatible = "socionext,uniphier-pxs3-perictrl",
"simple-mfd", "syscon";
reg = <0x59820000 0x200>;
peri_clk: clock {
compatible = "socionext,uniphier-pxs3-peri-clock";
#clock-cells = <1>;
};
peri_rst: reset {
compatible = "socionext,uniphier-pxs3-peri-reset";
#reset-cells = <1>;
};
};
emmc: sdhc@5a000000 {
compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc";
reg = <0x5a000000 0x400>;
interrupts = <0 78 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_emmc>;
clocks = <&sys_clk 4>;
resets = <&sys_rst 4>;
bus-width = <8>;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
mmc-pwrseq = <&emmc_pwrseq>;
cdns,phy-input-delay-legacy = <9>;
cdns,phy-input-delay-mmc-highspeed = <2>;
cdns,phy-input-delay-mmc-ddr = <3>;
cdns,phy-dll-delay-sdclk = <21>;
cdns,phy-dll-delay-sdclk-hsmmc = <21>;
};
sd: sdhc@5a400000 {
compatible = "socionext,uniphier-sd-v3.1.1";
status = "disabled";
reg = <0x5a400000 0x800>;
interrupts = <0 76 4>;
pinctrl-names = "default", "uhs";
pinctrl-0 = <&pinctrl_sd>;
pinctrl-1 = <&pinctrl_sd_uhs>;
clocks = <&sd_clk 0>;
reset-names = "host";
resets = <&sd_rst 0>;
bus-width = <4>;
cap-sd-highspeed;
sd-uhs-sdr12;
sd-uhs-sdr25;
sd-uhs-sdr50;
};
soc_glue: soc-glue@5f800000 {
compatible = "socionext,uniphier-pxs3-soc-glue",
"simple-mfd", "syscon";
reg = <0x5f800000 0x2000>;
pinctrl: pinctrl {
compatible = "socionext,uniphier-pxs3-pinctrl";
};
};
soc-glue@5f900000 {
compatible = "socionext,uniphier-pxs3-soc-glue-debug",
"simple-mfd";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x5f900000 0x2000>;
efuse@100 {
compatible = "socionext,uniphier-efuse";
reg = <0x100 0x28>;
};
efuse@200 {
compatible = "socionext,uniphier-efuse";
reg = <0x200 0x68>;
#address-cells = <1>;
#size-cells = <1>;
/* USB cells */
usb_rterm0: trim@54,4 {
reg = <0x54 1>;
bits = <4 2>;
};
usb_rterm1: trim@55,4 {
reg = <0x55 1>;
bits = <4 2>;
};
usb_rterm2: trim@58,4 {
reg = <0x58 1>;
bits = <4 2>;
};
usb_rterm3: trim@59,4 {
reg = <0x59 1>;
bits = <4 2>;
};
usb_sel_t0: trim@54,0 {
reg = <0x54 1>;
bits = <0 4>;
};
usb_sel_t1: trim@55,0 {
reg = <0x55 1>;
bits = <0 4>;
};
usb_sel_t2: trim@58,0 {
reg = <0x58 1>;
bits = <0 4>;
};
usb_sel_t3: trim@59,0 {
reg = <0x59 1>;
bits = <0 4>;
};
usb_hs_i0: trim@56,0 {
reg = <0x56 1>;
bits = <0 4>;
};
usb_hs_i2: trim@5a,0 {
reg = <0x5a 1>;
bits = <0 4>;
};
};
};
aidet: aidet@5fc20000 {
compatible = "socionext,uniphier-pxs3-aidet";
reg = <0x5fc20000 0x200>;
interrupt-controller;
#interrupt-cells = <2>;
};
gic: interrupt-controller@5fe00000 {
compatible = "arm,gic-v3";
reg = <0x5fe00000 0x10000>, /* GICD */
<0x5fe80000 0x80000>; /* GICR */
interrupt-controller;
#interrupt-cells = <3>;
interrupts = <1 9 4>;
};
sysctrl@61840000 {
compatible = "socionext,uniphier-pxs3-sysctrl",
"simple-mfd", "syscon";
reg = <0x61840000 0x10000>;
sys_clk: clock {
compatible = "socionext,uniphier-pxs3-clock";
#clock-cells = <1>;
};
sys_rst: reset {
compatible = "socionext,uniphier-pxs3-reset";
#reset-cells = <1>;
};
watchdog {
compatible = "socionext,uniphier-wdt";
};
};
eth0: ethernet@65000000 {
compatible = "socionext,uniphier-pxs3-ave4";
status = "disabled";
reg = <0x65000000 0x8500>;
interrupts = <0 66 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ether_rgmii>;
clock-names = "ether";
clocks = <&sys_clk 6>;
reset-names = "ether";
resets = <&sys_rst 6>;
phy-mode = "rgmii";
local-mac-address = [00 00 00 00 00 00];
socionext,syscon-phy-mode = <&soc_glue 0>;
mdio0: mdio {
#address-cells = <1>;
#size-cells = <0>;
};
};
eth1: ethernet@65200000 {
compatible = "socionext,uniphier-pxs3-ave4";
status = "disabled";
reg = <0x65200000 0x8500>;
interrupts = <0 67 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ether1_rgmii>;
clock-names = "ether";
clocks = <&sys_clk 7>;
reset-names = "ether";
resets = <&sys_rst 7>;
phy-mode = "rgmii";
local-mac-address = [00 00 00 00 00 00];
socionext,syscon-phy-mode = <&soc_glue 1>;
mdio1: mdio {
#address-cells = <1>;
#size-cells = <0>;
};
};
_usb0: usb@65a00000 {
compatible = "socionext,uniphier-dwc3", "snps,dwc3";
status = "disabled";
reg = <0x65a00000 0xcd00>;
interrupt-names = "host", "peripheral";
interrupts = <0 134 4>, <0 135 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>;
clock-names = "ref", "bus_early", "suspend";
clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
resets = <&usb0_rst 15>;
phys = <&usb0_hsphy0>, <&usb0_hsphy1>,
<&usb0_ssphy0>, <&usb0_ssphy1>;
dr_mode = "host";
};
usb-glue@65b00000 {
compatible = "socionext,uniphier-pxs3-dwc3-glue",
"simple-mfd";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x65b00000 0x400>;
usb0_rst: reset@0 {
compatible = "socionext,uniphier-pxs3-usb3-reset";
reg = <0x0 0x4>;
#reset-cells = <1>;
clock-names = "link";
clocks = <&sys_clk 12>;
reset-names = "link";
resets = <&sys_rst 12>;
};
usb0_vbus0: regulator@100 {
compatible = "socionext,uniphier-pxs3-usb3-regulator";
reg = <0x100 0x10>;
clock-names = "link";
clocks = <&sys_clk 12>;
reset-names = "link";
resets = <&sys_rst 12>;
};
usb0_vbus1: regulator@110 {
compatible = "socionext,uniphier-pxs3-usb3-regulator";
reg = <0x110 0x10>;
clock-names = "link";
clocks = <&sys_clk 12>;
reset-names = "link";
resets = <&sys_rst 12>;
};
usb0_hsphy0: hs-phy@200 {
compatible = "socionext,uniphier-pxs3-usb3-hsphy";
reg = <0x200 0x10>;
#phy-cells = <0>;
clock-names = "link", "phy";
clocks = <&sys_clk 12>, <&sys_clk 16>;
reset-names = "link", "phy";
resets = <&sys_rst 12>, <&sys_rst 16>;
vbus-supply = <&usb0_vbus0>;
nvmem-cell-names = "rterm", "sel_t", "hs_i";
nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>,
<&usb_hs_i0>;
};
usb0_hsphy1: hs-phy@210 {
compatible = "socionext,uniphier-pxs3-usb3-hsphy";
reg = <0x210 0x10>;
#phy-cells = <0>;
clock-names = "link", "phy";
clocks = <&sys_clk 12>, <&sys_clk 16>;
reset-names = "link", "phy";
resets = <&sys_rst 12>, <&sys_rst 16>;
vbus-supply = <&usb0_vbus1>;
nvmem-cell-names = "rterm", "sel_t", "hs_i";
nvmem-cells = <&usb_rterm1>, <&usb_sel_t1>,
<&usb_hs_i0>;
};
usb0_ssphy0: ss-phy@300 {
compatible = "socionext,uniphier-pxs3-usb3-ssphy";
reg = <0x300 0x10>;
#phy-cells = <0>;
clock-names = "link", "phy";
clocks = <&sys_clk 12>, <&sys_clk 17>;
reset-names = "link", "phy";
resets = <&sys_rst 12>, <&sys_rst 17>;
vbus-supply = <&usb0_vbus0>;
};
usb0_ssphy1: ss-phy@310 {
compatible = "socionext,uniphier-pxs3-usb3-ssphy";
reg = <0x310 0x10>;
#phy-cells = <0>;
clock-names = "link", "phy";
clocks = <&sys_clk 12>, <&sys_clk 18>;
reset-names = "link", "phy";
resets = <&sys_rst 12>, <&sys_rst 18>;
vbus-supply = <&usb0_vbus1>;
};
};
/* FIXME: U-Boot own node */
usb0: usb@65b00000 {
compatible = "socionext,uniphier-pxs3-dwc3";
status = "disabled";
reg = <0x65b00000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>;
dwc3@65a00000 {
compatible = "snps,dwc3";
reg = <0x65a00000 0x10000>;
interrupts = <0 134 4>;
dr_mode = "host";
tx-fifo-resize;
};
};
_usb1: usb@65c00000 {
compatible = "socionext,uniphier-dwc3", "snps,dwc3";
status = "disabled";
reg = <0x65c00000 0xcd00>;
interrupt-names = "host", "peripheral";
interrupts = <0 137 4>, <0 138 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>;
clock-names = "ref", "bus_early", "suspend";
clocks = <&sys_clk 13>, <&sys_clk 13>, <&sys_clk 13>;
resets = <&usb1_rst 15>;
phys = <&usb1_hsphy0>, <&usb1_hsphy1>,
<&usb1_ssphy0>;
dr_mode = "host";
};
usb-glue@65d00000 {
compatible = "socionext,uniphier-pxs3-dwc3-glue",
"simple-mfd";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x65d00000 0x400>;
usb1_rst: reset@0 {
compatible = "socionext,uniphier-pxs3-usb3-reset";
reg = <0x0 0x4>;
#reset-cells = <1>;
clock-names = "link";
clocks = <&sys_clk 13>;
reset-names = "link";
resets = <&sys_rst 13>;
};
usb1_vbus0: regulator@100 {
compatible = "socionext,uniphier-pxs3-usb3-regulator";
reg = <0x100 0x10>;
clock-names = "link";
clocks = <&sys_clk 13>;
reset-names = "link";
resets = <&sys_rst 13>;
};
usb1_vbus1: regulator@110 {
compatible = "socionext,uniphier-pxs3-usb3-regulator";
reg = <0x110 0x10>;
clock-names = "link";
clocks = <&sys_clk 13>;
reset-names = "link";
resets = <&sys_rst 13>;
};
usb1_hsphy0: hs-phy@200 {
compatible = "socionext,uniphier-pxs3-usb3-hsphy";
reg = <0x200 0x10>;
#phy-cells = <0>;
clock-names = "link", "phy", "phy-ext";
clocks = <&sys_clk 13>, <&sys_clk 20>,
<&sys_clk 14>;
reset-names = "link", "phy";
resets = <&sys_rst 13>, <&sys_rst 20>;
vbus-supply = <&usb1_vbus0>;
nvmem-cell-names = "rterm", "sel_t", "hs_i";
nvmem-cells = <&usb_rterm2>, <&usb_sel_t2>,
<&usb_hs_i2>;
};
usb1_hsphy1: hs-phy@210 {
compatible = "socionext,uniphier-pxs3-usb3-hsphy";
reg = <0x210 0x10>;
#phy-cells = <0>;
clock-names = "link", "phy", "phy-ext";
clocks = <&sys_clk 13>, <&sys_clk 20>,
<&sys_clk 14>;
reset-names = "link", "phy";
resets = <&sys_rst 13>, <&sys_rst 20>;
vbus-supply = <&usb1_vbus1>;
nvmem-cell-names = "rterm", "sel_t", "hs_i";
nvmem-cells = <&usb_rterm3>, <&usb_sel_t3>,
<&usb_hs_i2>;
};
usb1_ssphy0: ss-phy@300 {
compatible = "socionext,uniphier-pxs3-usb3-ssphy";
reg = <0x300 0x10>;
#phy-cells = <0>;
clock-names = "link", "phy", "phy-ext";
clocks = <&sys_clk 13>, <&sys_clk 21>,
<&sys_clk 14>;
reset-names = "link", "phy";
resets = <&sys_rst 13>, <&sys_rst 21>;
vbus-supply = <&usb1_vbus0>;
};
};
/* FIXME: U-Boot own node */
usb1: usb@65d00000 {
compatible = "socionext,uniphier-pxs3-dwc3";
status = "disabled";
reg = <0x65d00000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>;
dwc3@65c00000 {
compatible = "snps,dwc3";
reg = <0x65c00000 0x10000>;
interrupts = <0 137 4>;
dr_mode = "host";
tx-fifo-resize;
};
};
nand: nand@68000000 {
compatible = "socionext,uniphier-denali-nand-v5b";
status = "disabled";
reg-names = "nand_data", "denali_reg";
reg = <0x68000000 0x20>, <0x68100000 0x1000>;
interrupts = <0 65 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_nand>;
clock-names = "nand", "nand_x", "ecc";
clocks = <&sys_clk 2>, <&sys_clk 3>, <&sys_clk 3>;
resets = <&sys_rst 2>;
};
};
};
#include "uniphier-pinctrl.dtsi"