blob: 09a04bdcca136573a82d73286a129cd74060a756 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
#include <dt-bindings/gpio/gpio.h>
#include "armada-385.dtsi"
/ {
model = "Allied Telesis x530";
compatible = "alliedtelesis,x530", "marvell,armada385", "marvell,armada380";
chosen {
stdout-path = "serial0:115200n8";
bootargs = "console=ttyS0,115200 earlyprintk";
};
aliases {
spi1 = &spi1;
i2c0 = &i2c0;
};
memory {
device_type = "memory";
reg = <0 0x00000000 0 0x40000000>; /* 1 GB */
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x3d) 0 0xf4800000 0x80000
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
pcie-mem-aperture = <0xa0000000 0x40000000>;
};
eco-button-interrupt {
compatible = "atl,eco-button-interrupt";
eco-button-gpio = <&gpio0 14 GPIO_ACTIVE_LOW>;
};
board-reset {
compatible = "atl,phy_reset";
/* Physical board layout of reset pin is active-low but for the
* current driver we have to set it to active-high here.
*/
phy-reset-gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>,
<&gpio1 21 GPIO_ACTIVE_HIGH>;
};
phy-int {
compatible = "linux,uio-pdrv-genirq";
interrupt-parent = <&gpio0>;
interrupts = <6 IRQ_TYPE_EDGE_BOTH>;
};
led-enable {
compatible = "atl,led-enable";
led-enable-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
};
led_7seg {
compatible = "atl,of-led-7seg";
segment-gpios = <
&led_7seg_gpio 0 0
&led_7seg_gpio 1 0
&led_7seg_gpio 2 0
&led_7seg_gpio 3 0
&led_7seg_gpio 4 0
&led_7seg_gpio 5 0
&led_7seg_gpio 6 0
&led_7seg_gpio 7 0>;
};
poe {
compatible = "atl,periph-poe";
poe-reset-gpio = <&gpio0 15 GPIO_ACTIVE_HIGH>;
interrupt-parent = <&gpio0>;
interrupts = <20 IRQ_TYPE_EDGE_BOTH>;
};
};
&pciec {
status = "okay";
};
&pcie1 {
status = "okay";
};
&devbus_cs1 {
compatible = "marvell,mvebu-devbus";
status = "okay";
devbus,bus-width = <8>;
devbus,turn-off-ps = <60000>;
devbus,badr-skew-ps = <0>;
devbus,acc-first-ps = <124000>;
devbus,acc-next-ps = <248000>;
devbus,rd-setup-ps = <0>;
devbus,rd-hold-ps = <0>;
/* Write parameters */
devbus,sync-enable = <0>;
devbus,wr-high-ps = <60000>;
devbus,wr-low-ps = <60000>;
devbus,ale-wr-ps = <60000>;
nvs@0 {
status = "okay";
compatible = "mtd-ram";
reg = <0 0x00080000>;
bank-width = <1>;
label = "nvs";
};
};
&gpio0 {
poe-disable {
gpio-hog;
gpios = <16 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "poe-disable";
};
};
&gpio1 {
poe-mezz-reset {
gpio-hog;
gpios = <15 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "poe-mezz-reset";
};
};
&i2c0 {
clock-frequency = <100000>;
status = "okay";
mux@71 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "nxp,pca9544";
reg = <0x71>;
i2c-mux-idle-disconnect;
i2c@0 { /* POE devices MUX */
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
rng@3b {
compatible = "maxim,ds2476";
reg = <0x3b>;
};
hwmon@2e {
compatible = "adi,adt7476";
reg = <0x2e>;
};
hwmon@2d {
compatible = "adi,adt7476";
reg = <0x2d>;
};
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
rtc@68 {
compatible = "dallas,ds1340";
reg = <0x68>;
};
};
i2c@3 {
#address-cells = <1>;
#size-cells = <0>;
reg = <3>;
led_7seg_gpio: gpio@20 {
compatible = "nxp,pca9554";
gpio-controller;
#gpio-cells = <2>;
reg = <0x20>;
};
sfpgpio: gpio@27 { /* I2C to GPIO */
compatible = "nxp,pca9555";
gpio-controller;
#gpio-cells = <2>;
reg = <0x27>;
interrupt-parent = <&gpio0>;
interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
};
sfpmux: mux@77 { /* SFP I2C MUX */
#address-cells = <1>;
#size-cells = <0>;
compatible = "nxp,pca9544";
reg = <0x77>;
i2c-mux-idle-disconnect;
};
};
};
};
&spi1 {
status = "okay";
spi-flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>; /* Chip select 0 */
spi-max-frequency = <50000000>;
m25p,fast-read;
partition@u-boot {
reg = <0x00000000 0x00100000>;
label = "u-boot";
};
partition@u-boot-env {
reg = <0x00100000 0x00040000>;
label = "u-boot-env";
};
partition@unused {
reg = <0x00140000 0x00e80000>;
label = "unused";
};
partition@idprom {
reg = <0x00fc0000 0x00040000>;
label = "idprom";
};
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins>;
status = "okay";
};
&usb0 {
status = "okay";
};
&refclk {
clock-frequency = <25000000>;
};
&nand_controller { /* 256 MB */
status = "okay";
num-cs = <1>;
nand-ecc-strength = <4>;
nand-ecc-step-size = <512>;
marvell,nand-enable-arbiter;
nand-on-flash-bbt;
};