// SPDX-License-Identifier: GPL-2.0+
/*
 * Copyright (C) 2017 PHYTEC Messtechnik GmbH
 * Author: Wadim Egorov <w.egorov@phytec.de>
 */

#include <asm/io.h>
#include <common.h>
#include <dm.h>
#include <env.h>
#include <env_internal.h>
#include <i2c.h>
#include <i2c_eeprom.h>
#include <netdev.h>
#include "som.h"
#include <power/regulator.h>
#include <power/rk8xx_pmic.h>

static int valid_rk3288_som(struct rk3288_som *som)
{
	unsigned char *p = (unsigned char *)som;
	unsigned char *e = p + sizeof(struct rk3288_som) - 1;
	int hw = 0;

	while (p < e) {
		hw += hweight8(*p);
		p++;
	}

	return hw == som->bs;
}

int rk3288_board_late_init(void)
{
	int ret;
	struct udevice *dev;
	struct rk3288_som opt;
	int off;

	/* Get the identificatioin page of M24C32-D EEPROM */
	off = fdt_path_offset(gd->fdt_blob, "eeprom0");
	if (off < 0) {
		printf("%s: No eeprom0 path offset\n", __func__);
		return off;
	}

	ret = uclass_get_device_by_of_offset(UCLASS_I2C_EEPROM, off, &dev);
	if (ret) {
		printf("%s: Could not find EEPROM\n", __func__);
		return ret;
	}

	ret = i2c_set_chip_offset_len(dev, 2);
	if (ret)
		return ret;

	ret = i2c_eeprom_read(dev, 0, (uint8_t *)&opt,
				sizeof(struct rk3288_som));
	if (ret) {
		printf("%s: Could not read EEPROM\n", __func__);
		return ret;
	}

	if (opt.api_version != 0 || !valid_rk3288_som(&opt)) {
		printf("Invalid data or wrong EEPROM layout version.\n");
		/* Proceed anyway, since there is no fallback option */
	}

	if (is_valid_ethaddr(opt.mac))
		eth_env_set_enetaddr("ethaddr", opt.mac);

	return 0;
}

#ifdef CONFIG_SPL_BUILD
#if !defined(CONFIG_SPL_OF_PLATDATA)
static int phycore_init(void)
{
	struct udevice *pmic;
	int ret;

	ret = uclass_first_device_err(UCLASS_PMIC, &pmic);
	if (ret)
		return ret;

#if defined(CONFIG_SPL_POWER_SUPPORT)
	/* Increase USB input current to 2A */
	ret = rk818_spl_configure_usb_input_current(pmic, 2000);
	if (ret)
		return ret;

	/* Close charger when USB lower then 3.26V */
	ret = rk818_spl_configure_usb_chrg_shutdown(pmic, 3260000);
	if (ret)
		return ret;
#endif

	return 0;
}
#endif

void spl_board_init(void)
{
#if !defined(CONFIG_SPL_OF_PLATDATA)
	int ret;

	if (of_machine_is_compatible("phytec,rk3288-phycore-som")) {
		ret = phycore_init();
		if (ret) {
			debug("Failed to set up phycore power settings: %d\n",
			      ret);
			return;
		}
	}
#endif
}
#endif