blob: 6ea6e413950f3dc39cc11a257db951809d26f704 [file] [log] [blame]
-------------
SDP in U-Boot
-------------
SDP stands for serial download protocol. It is the protocol used in NXP's
i.MX SoCs ROM Serial Downloader and provides means to download a program
image to the chip over USB and UART serial connection.
The implementation in U-Boot uses the USB Downloader Gadget (g_dnl) to
provide a SDP implementation over USB. This allows to download program
images to the target in SPL/U-Boot using the same protocol/tooling the
SoC's recovery mechanism is using.
The SDP protocol over USB is a USB HID class protocol. USB HID class
protocols allow to access a USB device without OS specific drivers. The
U-Boot implementation has primarly been tested using the open source
imx_loader utility (https://github.com/boundarydevices/imx_usb_loader).
imx_usb_loader is a very nice tool by Boundary Devices that allow to
install U-Boot without a JTAG debugger, using the USB boot mode as
described in the manual. It is a replacement for Freescale's
MFGTOOLS.
The host side utilities are typically capable to interpret the i.MX
specific image header (see doc/README.imximage). There are extensions
for imx_loader's imx_usb utility which allow to interpret the U-Boot
specific legacy image format (see mkimage(1)). Also the U-Boot side
support beside the i.MX specific header the U-Boot legacy header.
1. Using imx_usb_loader for first install with SPL
--------------------------------------------------
This implementation can be started in U-Boot using the sdp command
(CONFIG_CMD_USB_SDP) or in SPL if Serial Downloader boot mode has been
detected (CONFIG_SPL_USB_SDP_SUPPORT).
A typical use case is downloading full U-Boot after SPL has been
downloaded through the boot ROM's Serial Downloader. Using boot mode
detection the SPL will run the SDP implementation automatically in
this case:
# imx_usb SPL
Targets Serial Console:
Trying to boot from USB SDP
SDP: initialize...
SDP: handle requests...
At this point the SPL reenumerated as a new HID device and emulating
the boot ROM's SDP protocol. The USB VID/PID will depend on standard
U-Boot configurations CONFIG_G_DNL_(VENDOR|PRODUCT)_NUM. Make sure
imx_usb is aware of the USB VID/PID for your device by adding a
configuration entry in imx_usb.conf:
0x1b67:0x4fff, mx6_usb_sdp_spl.conf
And the device specific configuration file mx6_usb_sdp_spl.conf:
mx6_spl_sdp
hid,uboot_header,1024,0x910000,0x10000000,1G,0x00900000,0x40000
This allows to download the regular U-Boot with legacy image headers
(u-boot.img) using a second invocation of imx_usb:
# imx_usb u-boot.img
Furthermore, when U-Boot is running the sdp command can be used to
download and run scripts:
# imx_usb script.scr
imx_usb configuration files can be also used to download multiple
files and of arbitrary types, e.g.
mx6_usb_sdp_uboot
hid,1024,0x10000000,1G,0x00907000,0x31000
full.itb:load 0x12100000
boot.scr:load 0x12000000,jump 0x12000000
There is also a batch mode which allows imx_usb to handle multiple
consecutive reenumerations by adding multiple VID/PID specifications
in imx_usb.conf:
0x15a2:0x0061, mx6_usb_rom.conf, 0x1b67:0x4fff, mx6_usb_sdp_spl.conf
In this mode the file to download (imx_usb job) needs to be specified
in the configuration files.
mx6_usb_rom.conf:
mx6_qsb
hid,1024,0x910000,0x10000000,1G,0x00900000,0x40000
SPL:jump header2
mx6_usb_sdp_spl.conf:
mx6_spl_sdp
hid,uboot_header,1024,0x10000000,1G,0x00907000,0x31000
u-boot.img:jump header2
With that SPL and U-Boot can be downloaded with a single invocation
of imx_usb without arguments:
# imx_usb
2. Using imx_usb_loader non-SPL images
---------------------------------------
Booting in USB mode, the i.MX6 announces itself to the Linux Host as:
Bus 001 Device 111: ID 15a2:0061 Freescale Semiconductor, Inc.
imx_usb_loader is able to download a single file (u-boot.imx)
to the board. For boards without SPL support, it is enough to
issue the command:
sudo ../imx_usb_loader/imx_usb -v u-boot.imx