/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright 2018 NXP
 */

#ifndef __IMX8QM_MEK_H
#define __IMX8QM_MEK_H

#include <linux/sizes.h>
#include <asm/arch/imx-regs.h>

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_TEXT_BASE				0x0
#define CONFIG_SPL_MAX_SIZE				(124 * 1024)
#define CONFIG_SYS_MONITOR_LEN				(1024 * 1024)
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR		0x800
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION		0

#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_STACK		0x013E000
#define CONFIG_SPL_BSS_START_ADDR	0x00128000
#define CONFIG_SPL_BSS_MAX_SIZE		0x1000	/* 4 KB */
#define CONFIG_SYS_SPL_MALLOC_START	0x00120000
#define CONFIG_SYS_SPL_MALLOC_SIZE	0x3000	/* 12 KB */
#define CONFIG_SERIAL_LPUART_BASE	0x5a060000
#define CONFIG_MALLOC_F_ADDR		0x00120000

#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE

#define CONFIG_SPL_ABORT_ON_RAW_IMAGE

#define CONFIG_OF_EMBED
#endif

#define CONFIG_REMAKE_ELF

#define CONFIG_BOARD_EARLY_INIT_F

/* Flat Device Tree Definitions */
#define CONFIG_OF_BOARD_SETUP

#undef CONFIG_CMD_EXPORTENV
#undef CONFIG_CMD_IMPORTENV
#undef CONFIG_CMD_IMLS

#undef CONFIG_CMD_CRC32

#define CONFIG_SYS_FSL_ESDHC_ADDR       0
#define USDHC1_BASE_ADDR                0x5B010000
#define USDHC2_BASE_ADDR                0x5B020000
#define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */

#define CONFIG_ENV_OVERWRITE

#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS		\
	"script=boot.scr\0" \
	"image=Image\0" \
	"panel=NULL\0" \
	"console=ttyLP0,${baudrate} earlycon=lpuart32,0x5a060000,${baudrate}\0" \
	"fdt_addr=0x83000000\0"			\
	"fdt_high=0xffffffffffffffff\0"		\
	"boot_fdt=try\0" \
	"fdt_file=fsl-imx8qxp-mek.dtb\0" \
	"initrd_addr=0x83800000\0"		\
	"initrd_high=0xffffffffffffffff\0" \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
	"mmcautodetect=yes\0" \
	"mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
		"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
		"run mmcargs; " \
		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
			"if run loadfdt; then " \
				"booti ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"echo WARN: Cannot load the DT; " \
			"fi; " \
		"else " \
			"echo wait for boot; " \
		"fi;\0" \
	"netargs=setenv bootargs console=${console} " \
		"root=/dev/nfs " \
		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
	"netboot=echo Booting from net ...; " \
		"run netargs;  " \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"${get_cmd} ${loadaddr} ${image}; " \
		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
				"booti ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"echo WARN: Cannot load the DT; " \
			"fi; " \
		"else " \
			"booti; " \
		"fi;\0"

#define CONFIG_BOOTCOMMAND \
	   "mmc dev ${mmcdev}; if mmc rescan; then " \
		   "if run loadbootscript; then " \
			   "run bootscript; " \
		   "else " \
			   "if run loadimage; then " \
				   "run mmcboot; " \
			   "else run netboot; " \
			   "fi; " \
		   "fi; " \
	   "else booti ${loadaddr} - ${fdt_addr}; fi"

/* Link Definitions */
#define CONFIG_LOADADDR			0x80280000

#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR

#define CONFIG_SYS_INIT_SP_ADDR         0x80200000

/* Default environment is in SD */
#define CONFIG_ENV_SIZE			0x1000
#define CONFIG_ENV_OFFSET		(64 * SZ_64K)
#define CONFIG_SYS_MMC_ENV_PART		0	/* user area */

#define CONFIG_SYS_MMC_IMG_LOAD_PART	1

/* On LPDDR4 board, USDHC1 is for eMMC, USDHC2 is for SD on CPU board */
#define CONFIG_SYS_MMC_ENV_DEV		1   /* USDHC2 */
#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */
#define CONFIG_SYS_FSL_USDHC_NUM	2

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (32 * 1024)) * 1024)

#define CONFIG_SYS_SDRAM_BASE		0x80000000
#define PHYS_SDRAM_1			0x80000000
#define PHYS_SDRAM_2			0x880000000
#define PHYS_SDRAM_1_SIZE		0x80000000	/* 2 GB */
#define PHYS_SDRAM_2_SIZE		0x100000000	/* 4 GB */

/* Serial */
#define CONFIG_BAUDRATE			115200

/* Generic Timer Definitions */
#define COUNTER_FREQUENCY		8000000	/* 8MHz */

/* Networking */
#define CONFIG_FEC_XCV_TYPE		RGMII
#define FEC_QUIRK_ENET_MAC

#endif /* __IMX8QM_MEK_H */