#
# Copyright (c) 2013-2019, ARM Limited and Contributors. All rights reserved.
#
# SPDX-License-Identifier: BSD-3-Clause
#

include lib/libfdt/libfdt.mk
include lib/xlat_tables_v2/xlat_tables.mk

PLAT_INCLUDES		:=	-Iplat/rpi/common/include		\
				-Iplat/rpi/rpi4/include

PLAT_BL_COMMON_SOURCES	:=	drivers/ti/uart/aarch64/16550_console.S	\
				plat/rpi/common/rpi3_common.c		\
				${XLAT_TABLES_LIB_SRCS}

BL31_SOURCES		+=	lib/cpus/aarch64/cortex_a72.S		\
				plat/rpi/rpi4/aarch64/plat_helpers.S	\
				drivers/arm/gic/common/gic_common.c     \
				drivers/arm/gic/v2/gicv2_helpers.c      \
				drivers/arm/gic/v2/gicv2_main.c         \
				plat/common/plat_gicv2.c                \
				plat/rpi/rpi4/rpi4_bl31_setup.c		\
				plat/rpi/common/rpi3_pm.c		\
				plat/common/plat_psci_common.c		\
				plat/rpi/common/rpi3_topology.c		\
				${LIBFDT_SRCS}

# For now we only support BL31, using the kernel loaded by the GPU firmware.
RESET_TO_BL31		:=	1

# All CPUs enter armstub8.bin.
COLD_BOOT_SINGLE_CPU	:=	0

# Tune compiler for Cortex-A72
ifeq ($(notdir $(CC)),armclang)
    TF_CFLAGS_aarch64	+=	-mcpu=cortex-a72
else ifneq ($(findstring clang,$(notdir $(CC))),)
    TF_CFLAGS_aarch64	+=	-mcpu=cortex-a72
else
    TF_CFLAGS_aarch64	+=	-mtune=cortex-a72
endif


# Enable all errata workarounds for Cortex-A72
ERRATA_A72_859971		:= 1

WORKAROUND_CVE_2017_5715	:= 1

# Add new default target when compiling this platform
all: bl31

# Build config flags
# ------------------

# Disable stack protector by default
ENABLE_STACK_PROTECTOR	 	:= 0

# Have different sections for code and rodata
SEPARATE_CODE_AND_RODATA	:= 1

# Use Coherent memory
USE_COHERENT_MEM		:= 1

# Platform build flags
# --------------------

# Assume that BL33 isn't the Linux kernel by default
RPI3_DIRECT_LINUX_BOOT		:= 0

# BL33 images are in AArch64 by default
RPI3_BL33_IN_AARCH32		:= 0

# UART to use at runtime. -1 means the runtime UART is disabled.
# Any other value means the default UART will be used.
RPI3_RUNTIME_UART		:= 0

# Use normal memory mapping for ROM, FIP, SRAM and DRAM
RPI3_USE_UEFI_MAP		:= 0

# Process platform flags
# ----------------------

$(eval $(call add_define,RPI3_BL33_IN_AARCH32))
$(eval $(call add_define,RPI3_DIRECT_LINUX_BOOT))
ifdef RPI3_PRELOADED_DTB_BASE
$(eval $(call add_define,RPI3_PRELOADED_DTB_BASE))
endif
$(eval $(call add_define,RPI3_RUNTIME_UART))
$(eval $(call add_define,RPI3_USE_UEFI_MAP))

# Verify build config
# -------------------
#
ifneq (${RPI3_DIRECT_LINUX_BOOT}, 0)
  ifndef RPI3_PRELOADED_DTB_BASE
      $(error Error: RPI3_PRELOADED_DTB_BASE needed if RPI3_DIRECT_LINUX_BOOT=1)
  endif
endif

ifeq (${ARCH},aarch32)
  $(error Error: AArch32 not supported on rpi4)
endif

ifneq ($(ENABLE_STACK_PROTECTOR), 0)
PLAT_BL_COMMON_SOURCES	+=	drivers/rpi3/rng/rpi3_rng.c		\
				plat/rpi/common/rpi3_stack_protector.c
endif