/*
 * Copyright (c) 2018, ARM Limited and Contributors. All rights reserved.
 *
 * SPDX-License-Identifier: BSD-3-Clause
 */

#include <platform_def.h>

#include <drivers/arm/css/css_mhu_doorbell.h>
#include <drivers/arm/css/scmi.h>
#include <drivers/arm/css/sds.h>
#include <common/debug.h>
#include <lib/mmio.h>
#include <lib/utils.h>
#include <plat/arm/common/plat_arm.h>

#include "n1sdp_def.h"

/*
 * Memory information structure stored in SDS.
 * This structure holds the total DDR memory size which will be
 * used when zeroing out the entire DDR memory before enabling
 * the ECC capability in DMCs.
 */
struct n1sdp_mem_info {
	uint32_t ddr_size_gb;
};

/*
 * BL33 image information structure stored in SDS.
 * This structure holds the source & destination addresses and
 * the size of the BL33 image which will be loaded by BL31.
 */
struct n1sdp_bl33_info {
	uint32_t bl33_src_addr;
	uint32_t bl33_dst_addr;
	uint32_t bl33_size;
};

static scmi_channel_plat_info_t n1sdp_scmi_plat_info = {
		.scmi_mbx_mem = N1SDP_SCMI_PAYLOAD_BASE,
		.db_reg_addr = PLAT_CSS_MHU_BASE + CSS_SCMI_MHU_DB_REG_OFF,
		.db_preserve_mask = 0xfffffffe,
		.db_modify_mask = 0x1,
		.ring_doorbell = &mhu_ring_doorbell,
};

scmi_channel_plat_info_t *plat_css_get_scmi_info()
{
	return &n1sdp_scmi_plat_info;
}

const plat_psci_ops_t *plat_arm_psci_override_pm_ops(plat_psci_ops_t *ops)
{
	return css_scmi_override_pm_ops(ops);
}

/*
 * N1SDP platform supports RDIMMs with ECC capability. To use the ECC
 * capability, the entire DDR memory space has to be zeroed out before
 * enabling the ECC bits in DMC620. Zeroing out several gigabytes of
 * memory from SCP is quite time consuming so the following function
 * is added to zero out the DDR memory from application processor which is
 * much faster compared to SCP. BL33 binary cannot be copied to DDR memory
 * before enabling ECC so copy_bl33 function is added to copy BL33 binary
 * from IOFPGA-DDR3 memory to main DDR4 memory.
 */

void dmc_ecc_setup(uint32_t ddr_size_gb)
{
	uint64_t dram2_size;

	dram2_size = (ddr_size_gb * 1024UL * 1024UL * 1024UL) -
			ARM_DRAM1_SIZE;

	INFO("Zeroing DDR memories\n");
	zero_normalmem((void *)ARM_DRAM1_BASE, ARM_DRAM1_SIZE);
	flush_dcache_range(ARM_DRAM1_BASE, ARM_DRAM1_SIZE);
	zero_normalmem((void *)ARM_DRAM2_BASE, dram2_size);
	flush_dcache_range(ARM_DRAM2_BASE, dram2_size);

	INFO("Enabling ECC on DMCs\n");
	/* Set DMCs to CONFIG state before writing ERR0CTLR0 register */
	mmio_write_32(N1SDP_DMC0_MEMC_CMD_REG, N1SDP_DMC_MEMC_CMD_CONFIG);
	mmio_write_32(N1SDP_DMC1_MEMC_CMD_REG, N1SDP_DMC_MEMC_CMD_CONFIG);

	/* Enable ECC in DMCs */
	mmio_setbits_32(N1SDP_DMC0_ERR0CTLR0_REG, N1SDP_DMC_ERR0CTLR0_ECC_EN);
	mmio_setbits_32(N1SDP_DMC1_ERR0CTLR0_REG, N1SDP_DMC_ERR0CTLR0_ECC_EN);

	/* Set DMCs to READY state */
	mmio_write_32(N1SDP_DMC0_MEMC_CMD_REG, N1SDP_DMC_MEMC_CMD_READY);
	mmio_write_32(N1SDP_DMC1_MEMC_CMD_REG, N1SDP_DMC_MEMC_CMD_READY);
}

void copy_bl33(uint32_t src, uint32_t dst, uint32_t size)
{
	uint32_t i;

	INFO("Copying BL33 to DDR memory\n");
	for (i = 0; i < size; i = i + 8)
		mmio_write_64((dst + i), mmio_read_64(src + i));

	for (i = 0; i < size; i = i + 8) {
		if (mmio_read_64(src + i) != mmio_read_64(dst + i)) {
			ERROR("Copy failed!\n");
			panic();
		}
	}
}

void bl31_platform_setup(void)
{
	int ret;
	struct n1sdp_mem_info mem_info;
	struct n1sdp_bl33_info bl33_info;

	arm_bl31_platform_setup();

	ret = sds_init();
	if (ret != SDS_OK) {
		ERROR("SDS initialization failed\n");
		panic();
	}

	ret = sds_struct_read(N1SDP_SDS_MEM_INFO_STRUCT_ID,
				N1SDP_SDS_MEM_INFO_OFFSET,
				&mem_info,
				N1SDP_SDS_MEM_INFO_SIZE,
				SDS_ACCESS_MODE_NON_CACHED);
	if (ret != SDS_OK) {
		ERROR("Error getting memory info from SDS\n");
		panic();
	}
	dmc_ecc_setup(mem_info.ddr_size_gb);

	ret = sds_struct_read(N1SDP_SDS_BL33_INFO_STRUCT_ID,
				N1SDP_SDS_BL33_INFO_OFFSET,
				&bl33_info,
				N1SDP_SDS_BL33_INFO_SIZE,
				SDS_ACCESS_MODE_NON_CACHED);
	if (ret != SDS_OK) {
		ERROR("Error getting BL33 info from SDS\n");
		panic();
	}
	copy_bl33(bl33_info.bl33_src_addr,
			bl33_info.bl33_dst_addr,
			bl33_info.bl33_size);
	/*
	 * Pass DDR memory size info to BL33. This method is followed as
	 * currently there is no BL1/BL2 involved in boot flow of N1SDP.
	 * When TBBR is implemented for N1SDP, this method should be removed
	 * and DDR memory size shoule be passed to BL33 using NT_FW_CONFIG
	 * passing mechanism.
	 */
	mmio_write_32(N1SDP_DDR_MEM_INFO_BASE, mem_info.ddr_size_gb);
}