| // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) | |
| /* | |
| * Copyright (C) STMicroelectronics 2018-2019 - All Rights Reserved | |
| * Author: Alexandre Torgue <alexandre.torgue@st.com>. | |
| */ | |
| /dts-v1/; | |
| #include "stm32mp157c.dtsi" | |
| #include "stm32mp157cac-pinctrl.dtsi" | |
| / { | |
| model = "STMicroelectronics STM32MP157A-DK1 Discovery Board"; | |
| compatible = "st,stm32mp157a-dk1", "st,stm32mp157"; | |
| aliases { | |
| serial0 = &uart4; | |
| serial1 = &usart3; | |
| serial2 = &uart7; | |
| }; | |
| chosen { | |
| stdout-path = "serial0:115200n8"; | |
| }; | |
| }; | |
| &clk_hse { | |
| st,digbypass; | |
| }; | |
| &i2c4 { | |
| pinctrl-names = "default"; | |
| pinctrl-0 = <&i2c4_pins_a>; | |
| i2c-scl-rising-time-ns = <185>; | |
| i2c-scl-falling-time-ns = <20>; | |
| status = "okay"; | |
| pmic: stpmic@33 { | |
| compatible = "st,stpmic1"; | |
| reg = <0x33>; | |
| interrupts-extended = <&exti_pwr 55 IRQ_TYPE_EDGE_FALLING>; | |
| interrupt-controller; | |
| #interrupt-cells = <2>; | |
| status = "okay"; | |
| st,main-control-register = <0x04>; | |
| st,vin-control-register = <0xc0>; | |
| st,usb-control-register = <0x20>; | |
| regulators { | |
| compatible = "st,stpmic1-regulators"; | |
| ldo1-supply = <&v3v3>; | |
| ldo3-supply = <&vdd_ddr>; | |
| ldo6-supply = <&v3v3>; | |
| vddcore: buck1 { | |
| regulator-name = "vddcore"; | |
| regulator-min-microvolt = <1200000>; | |
| regulator-max-microvolt = <1350000>; | |
| regulator-always-on; | |
| regulator-initial-mode = <0>; | |
| regulator-over-current-protection; | |
| }; | |
| vdd_ddr: buck2 { | |
| regulator-name = "vdd_ddr"; | |
| regulator-min-microvolt = <1350000>; | |
| regulator-max-microvolt = <1350000>; | |
| regulator-always-on; | |
| regulator-initial-mode = <0>; | |
| regulator-over-current-protection; | |
| }; | |
| vdd: buck3 { | |
| regulator-name = "vdd"; | |
| regulator-min-microvolt = <3300000>; | |
| regulator-max-microvolt = <3300000>; | |
| regulator-always-on; | |
| st,mask-reset; | |
| regulator-initial-mode = <0>; | |
| regulator-over-current-protection; | |
| }; | |
| v3v3: buck4 { | |
| regulator-name = "v3v3"; | |
| regulator-min-microvolt = <3300000>; | |
| regulator-max-microvolt = <3300000>; | |
| regulator-always-on; | |
| regulator-over-current-protection; | |
| regulator-initial-mode = <0>; | |
| }; | |
| v1v8_audio: ldo1 { | |
| regulator-name = "v1v8_audio"; | |
| regulator-min-microvolt = <1800000>; | |
| regulator-max-microvolt = <1800000>; | |
| regulator-always-on; | |
| }; | |
| v3v3_hdmi: ldo2 { | |
| regulator-name = "v3v3_hdmi"; | |
| regulator-min-microvolt = <3300000>; | |
| regulator-max-microvolt = <3300000>; | |
| regulator-always-on; | |
| }; | |
| vtt_ddr: ldo3 { | |
| regulator-name = "vtt_ddr"; | |
| regulator-min-microvolt = <500000>; | |
| regulator-max-microvolt = <750000>; | |
| regulator-always-on; | |
| regulator-over-current-protection; | |
| }; | |
| vdd_usb: ldo4 { | |
| regulator-name = "vdd_usb"; | |
| regulator-min-microvolt = <3300000>; | |
| regulator-max-microvolt = <3300000>; | |
| }; | |
| vdda: ldo5 { | |
| regulator-name = "vdda"; | |
| regulator-min-microvolt = <2900000>; | |
| regulator-max-microvolt = <2900000>; | |
| regulator-boot-on; | |
| }; | |
| v1v2_hdmi: ldo6 { | |
| regulator-name = "v1v2_hdmi"; | |
| regulator-min-microvolt = <1200000>; | |
| regulator-max-microvolt = <1200000>; | |
| regulator-always-on; | |
| }; | |
| vref_ddr: vref_ddr { | |
| regulator-name = "vref_ddr"; | |
| regulator-always-on; | |
| regulator-over-current-protection; | |
| }; | |
| }; | |
| }; | |
| }; | |
| &iwdg2 { | |
| timeout-sec = <32>; | |
| status = "okay"; | |
| }; | |
| &pwr { | |
| pwr-regulators { | |
| vdd-supply = <&vdd>; | |
| }; | |
| }; | |
| &rng1 { | |
| status = "okay"; | |
| }; | |
| &rtc { | |
| status = "okay"; | |
| }; | |
| &sdmmc1 { | |
| pinctrl-names = "default"; | |
| pinctrl-0 = <&sdmmc1_b4_pins_a>; | |
| broken-cd; | |
| st,neg-edge; | |
| bus-width = <4>; | |
| vmmc-supply = <&v3v3>; | |
| status = "okay"; | |
| }; | |
| &uart4 { | |
| pinctrl-names = "default"; | |
| pinctrl-0 = <&uart4_pins_a>; | |
| status = "okay"; | |
| }; | |
| &uart7 { | |
| pinctrl-names = "default"; | |
| pinctrl-0 = <&uart7_pins_a>; | |
| status = "disabled"; | |
| }; | |
| &usart3 { | |
| pinctrl-names = "default"; | |
| pinctrl-0 = <&usart3_pins_b>; | |
| status = "disabled"; | |
| }; | |
| /* ATF Specific */ | |
| #include <dt-bindings/clock/stm32mp1-clksrc.h> | |
| #include "stm32mp15-ddr3-1x4Gb-1066-binG.dtsi" | |
| #include "stm32mp157c-security.dtsi" | |
| / { | |
| aliases { | |
| gpio0 = &gpioa; | |
| gpio1 = &gpiob; | |
| gpio2 = &gpioc; | |
| gpio3 = &gpiod; | |
| gpio4 = &gpioe; | |
| gpio5 = &gpiof; | |
| gpio6 = &gpiog; | |
| gpio7 = &gpioh; | |
| gpio8 = &gpioi; | |
| gpio25 = &gpioz; | |
| i2c3 = &i2c4; | |
| }; | |
| }; | |
| /* CLOCK init */ | |
| &rcc { | |
| secure-status = "disabled"; | |
| st,clksrc = < | |
| CLK_MPU_PLL1P | |
| CLK_AXI_PLL2P | |
| CLK_MCU_PLL3P | |
| CLK_PLL12_HSE | |
| CLK_PLL3_HSE | |
| CLK_PLL4_HSE | |
| CLK_RTC_LSE | |
| CLK_MCO1_DISABLED | |
| CLK_MCO2_DISABLED | |
| >; | |
| st,clkdiv = < | |
| 1 /*MPU*/ | |
| 0 /*AXI*/ | |
| 0 /*MCU*/ | |
| 1 /*APB1*/ | |
| 1 /*APB2*/ | |
| 1 /*APB3*/ | |
| 1 /*APB4*/ | |
| 2 /*APB5*/ | |
| 23 /*RTC*/ | |
| 0 /*MCO1*/ | |
| 0 /*MCO2*/ | |
| >; | |
| st,pkcs = < | |
| CLK_CKPER_HSE | |
| CLK_FMC_ACLK | |
| CLK_QSPI_ACLK | |
| CLK_ETH_DISABLED | |
| CLK_SDMMC12_PLL4P | |
| CLK_DSI_DSIPLL | |
| CLK_STGEN_HSE | |
| CLK_USBPHY_HSE | |
| CLK_SPI2S1_PLL3Q | |
| CLK_SPI2S23_PLL3Q | |
| CLK_SPI45_HSI | |
| CLK_SPI6_HSI | |
| CLK_I2C46_HSI | |
| CLK_SDMMC3_PLL4P | |
| CLK_USBO_USBPHY | |
| CLK_ADC_CKPER | |
| CLK_CEC_LSE | |
| CLK_I2C12_HSI | |
| CLK_I2C35_HSI | |
| CLK_UART1_HSI | |
| CLK_UART24_HSI | |
| CLK_UART35_HSI | |
| CLK_UART6_HSI | |
| CLK_UART78_HSI | |
| CLK_SPDIF_PLL4P | |
| CLK_FDCAN_PLL4R | |
| CLK_SAI1_PLL3Q | |
| CLK_SAI2_PLL3Q | |
| CLK_SAI3_PLL3Q | |
| CLK_SAI4_PLL3Q | |
| CLK_RNG1_LSI | |
| CLK_RNG2_LSI | |
| CLK_LPTIM1_PCLK1 | |
| CLK_LPTIM23_PCLK3 | |
| CLK_LPTIM45_LSE | |
| >; | |
| /* VCO = 1300.0 MHz => P = 650 (CPU) */ | |
| pll1: st,pll@0 { | |
| cfg = < 2 80 0 0 0 PQR(1,0,0) >; | |
| frac = < 0x800 >; | |
| }; | |
| /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */ | |
| pll2: st,pll@1 { | |
| cfg = < 2 65 1 0 0 PQR(1,1,1) >; | |
| frac = < 0x1400 >; | |
| }; | |
| /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */ | |
| pll3: st,pll@2 { | |
| cfg = < 1 33 1 16 36 PQR(1,1,1) >; | |
| frac = < 0x1a04 >; | |
| }; | |
| /* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */ | |
| pll4: st,pll@3 { | |
| cfg = < 3 98 5 7 7 PQR(1,1,1) >; | |
| }; | |
| }; | |
| &bsec { | |
| board_id: board_id@ec { | |
| reg = <0xec 0x4>; | |
| status = "okay"; | |
| secure-status = "okay"; | |
| }; | |
| }; |