diff --git a/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen
new file mode 100644
index 0000000..1e6a23f
--- /dev/null
+++ b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen
@@ -0,0 +1,61 @@
+README on the ADC/Touchscreen Controller
+========================================
+
+The LH79524 and LH7A404 include a built-in Analog to Digital
+controller (ADC) that is used to process input from a touchscreen.
+The driver only implements a four-wire touch panel protocol.
+
+The touchscreen driver is maintenance free except for the pen-down or
+touch threshold.  Some resistive displays and board combinations may
+require tuning of this threshold.  The driver exposes some of it's
+internal state in the sys filesystem.  If the kernel is configured
+with it, CONFIG_SYSFS, and sysfs is mounted at /sys, there will be a
+directory
+
+  /sys/devices/platform/adc-lh7.0
+
+containing these files.
+
+  -r--r--r--    1 root     root         4096 Jan  1 00:00 samples
+  -rw-r--r--    1 root     root         4096 Jan  1 00:00 threshold
+  -r--r--r--    1 root     root         4096 Jan  1 00:00 threshold_range
+
+The threshold is the current touch threshold.  It defaults to 750 on
+most targets.
+
+  # cat threshold
+ 750
+
+The threshold_range contains the range of valid values for the
+threshold.  Values outside of this range will be silently ignored.
+
+  # cat threshold_range
+  0 1023
+
+To change the threshold, write a value to the threshold file.
+
+  # echo 500 > threshold
+  # cat threshold
+  500
+
+The samples file contains the most recently sampled values from the
+ADC.  There are 12.  Below are typical of the last sampled values when
+the pen has been released.  The first two and last two samples are for
+detecting whether or not the pen is down.  The third through sixth are
+X coordinate samples.  The seventh through tenth are Y coordinate
+samples.
+
+  # cat samples
+  1023 1023 0 0 0 0 530 529 530 529 1023 1023
+
+To determine a reasonable threshold, press on the touch panel with an
+appropriate stylus and read the values from samples.
+
+  # cat samples
+  1023 676 92 103 101 102 855 919 922 922 1023 679
+
+The first and eleventh samples are discarded.  Thus, the important
+values are the second and twelfth which are used to determine if the
+pen is down.  When both are below the threshold, the driver registers
+that the pen is down.  When either is above the threshold, it
+registers then pen is up.
diff --git a/Documentation/arm/Sharp-LH/LCDPanels b/Documentation/arm/Sharp-LH/LCDPanels
new file mode 100644
index 0000000..fb1b21c
--- /dev/null
+++ b/Documentation/arm/Sharp-LH/LCDPanels
@@ -0,0 +1,59 @@
+README on the LCD Panels
+========================
+
+Configuration options for several LCD panels, available from Logic PD,
+are included in the kernel source.  This README will help you
+understand the configuration data and give you some guidance for
+adding support for other panels if you wish.
+
+
+lcd-panels.h
+------------
+
+There is no way, at present, to detect which panel is attached to the
+system at runtime.  Thus the kernel configuration is static.  The file
+arch/arm/mach-ld7a40x/lcd-panels.h (or similar) defines all of the
+panel specific parameters.
+
+It should be possible for this data to be shared among several device
+families.  The current layout may be insufficiently general, but it is
+amenable to improvement.
+
+
+PIXEL_CLOCK
+-----------
+
+The panel data sheets will give a range of acceptable pixel clocks.
+The fundamental LCDCLK input frequency is divided down by a PCD
+constant in field '.tim2'.  It may happen that it is impossible to set
+the pixel clock within this range.  A clock which is too slow will
+tend to flicker.  For the highest quality image, set the clock as high
+as possible.
+
+
+MARGINS
+-------
+
+These values may be difficult to glean from the panel data sheet.  In
+the case of the Sharp panels, the upper margin is explicitly called
+out as a specific number of lines from the top of the frame.  The
+other values may not matter as much as the panels tend to
+automatically center the image.
+
+
+Sync Sense
+----------
+
+The sense of the hsync and vsync pulses may be called out in the data
+sheet.  On one panel, the sense of these pulses determine the height
+of the visible region on the panel.  Most of the Sharp panels use
+negative sense sync pulses set by the TIM2_IHS and TIM2_IVS bits in
+'.tim2'.
+
+
+Pel Layout
+----------
+
+The Sharp color TFT panels are all configured for 16 bit direct color
+modes.  The amba-lcd driver sets the pel mode to 565 for 5 bits of
+each red and blue and 6 bits of green.
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 08b7cc9..f47cf9a 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -270,6 +270,11 @@
 	  Say Y here if you intend to run this kernel on an Atmel
 	  AT91RM9200-based board.
 
+config ARCH_PNX4008
+	bool "Philips Nexperia PNX4008 Mobile"
+	help
+	  This enables support for Philips PNX4008 mobile platform.
+
 endchoice
 
 source "arch/arm/mach-clps711x/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 6f8e84c..6c97aa70 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -116,6 +116,7 @@
  machine-$(CONFIG_ARCH_REALVIEW)   := realview
  machine-$(CONFIG_ARCH_AT91RM9200) := at91rm9200
  machine-$(CONFIG_ARCH_EP93XX)     := ep93xx
+ machine-$(CONFIG_ARCH_PNX4008)    := pnx4008
 
 ifeq ($(CONFIG_ARCH_EBSA110),y)
 # This is what happens if you forget the IOCS16 line.
diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index b56f5e6..23016f6 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -605,8 +605,8 @@
 		b	__armv4_mmu_cache_off
 		b	__armv4_mmu_cache_flush
 
-		.word	0x00070000		@ ARMv6
-		.word	0x000f0000
+		.word	0x0007b000		@ ARMv6
+		.word	0x0007f000
 		b	__armv4_mmu_cache_on
 		b	__armv4_mmu_cache_off
 		b	__armv6_mmu_cache_flush
diff --git a/arch/arm/configs/lpd7a400_defconfig b/arch/arm/configs/lpd7a400_defconfig
index 67eaa26..bf9cf9c 100644
--- a/arch/arm/configs/lpd7a400_defconfig
+++ b/arch/arm/configs/lpd7a400_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.12-rc1-bk2
-# Mon Mar 28 00:06:33 2005
+# Linux kernel version: 2.6.12
+# Thu Nov  3 14:15:32 2005
 #
 CONFIG_ARM=y
 CONFIG_MMU=y
@@ -17,6 +17,7 @@
 CONFIG_CLEAN_COMPILE=y
 CONFIG_BROKEN_ON_SMP=y
 CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
 
 #
 # General setup
@@ -36,6 +37,8 @@
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
 CONFIG_BASE_FULL=y
 CONFIG_FUTEX=y
 # CONFIG_EPOLL is not set
@@ -71,6 +74,7 @@
 # CONFIG_ARCH_SA1100 is not set
 # CONFIG_ARCH_S3C2410 is not set
 # CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7952X is not set
 CONFIG_ARCH_LH7A40X=y
 # CONFIG_ARCH_OMAP is not set
 # CONFIG_ARCH_VERSATILE is not set
@@ -84,6 +88,7 @@
 CONFIG_MACH_LPD7A400=y
 # CONFIG_MACH_LPD7A404 is not set
 CONFIG_ARCH_LH7A400=y
+CONFIG_LPD7A40X_CPLD_SSP=y
 # CONFIG_LH7A40X_CONTIGMEM is not set
 # CONFIG_LH7A40X_ONE_BANK_PER_NODE is not set
 
@@ -110,6 +115,8 @@
 #
 # Bus support
 #
+CONFIG_ARM_AMBA=y
+CONFIG_ISA_DMA_API=y
 
 #
 # PCCARD (PCMCIA/CardBus) support
@@ -119,6 +126,7 @@
 #
 # Kernel Features
 #
+# CONFIG_SMP is not set
 CONFIG_PREEMPT=y
 CONFIG_DISCONTIGMEM=y
 CONFIG_ALIGNMENT_TRAP=y
@@ -175,7 +183,7 @@
 # CONFIG_MTD_CONCAT is not set
 CONFIG_MTD_PARTITIONS=y
 # CONFIG_MTD_REDBOOT_PARTS is not set
-# CONFIG_MTD_CMDLINE_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
 # CONFIG_MTD_AFS_PARTS is not set
 
 #
@@ -217,7 +225,10 @@
 # Mapping drivers for chip access
 #
 # CONFIG_MTD_COMPLEX_MAPPINGS is not set
-# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_START=0x00000000
+CONFIG_MTD_PHYSMAP_LEN=0x04000000
+CONFIG_MTD_PHYSMAP_BANKWIDTH=4
 # CONFIG_MTD_ARM_INTEGRATOR is not set
 # CONFIG_MTD_EDB7312 is not set
 
@@ -254,7 +265,6 @@
 #
 # Block devices
 #
-# CONFIG_BLK_DEV_FD is not set
 # CONFIG_BLK_DEV_COW_COMMON is not set
 CONFIG_BLK_DEV_LOOP=y
 # CONFIG_BLK_DEV_CRYPTOLOOP is not set
@@ -288,13 +298,15 @@
 # CONFIG_BLK_DEV_IDECD is not set
 # CONFIG_BLK_DEV_IDETAPE is not set
 # CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_BLK_DEV_IDESCSI is not set
 # CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_POLL=y
 
 #
 # IDE chipset support/bugfixes
 #
 CONFIG_IDE_GENERIC=y
-# CONFIG_IDE_ARM is not set
+CONFIG_IDE_ARM=y
 # CONFIG_BLK_DEV_IDEDMA is not set
 # CONFIG_IDEDMA_AUTO is not set
 # CONFIG_BLK_DEV_HD is not set
@@ -302,7 +314,37 @@
 #
 # SCSI device support
 #
-# CONFIG_SCSI is not set
+CONFIG_SCSI=y
+# CONFIG_SCSI_PROC_FS is not set
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+# CONFIG_BLK_DEV_SD is not set
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+
+#
+# SCSI Transport Attributes
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+
+#
+# SCSI low-level drivers
+#
+# CONFIG_SCSI_SATA is not set
+# CONFIG_SCSI_DEBUG is not set
 
 #
 # Multi-device support (RAID and LVM)
@@ -331,7 +373,6 @@
 #
 CONFIG_PACKET=y
 # CONFIG_PACKET_MMAP is not set
-# CONFIG_NETLINK_DEV is not set
 CONFIG_UNIX=y
 # CONFIG_NET_KEY is not set
 CONFIG_INET=y
@@ -438,13 +479,10 @@
 #
 # Userland interfaces
 #
-CONFIG_INPUT_MOUSEDEV=y
-CONFIG_INPUT_MOUSEDEV_PSAUX=y
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_MOUSEDEV is not set
 # CONFIG_INPUT_JOYDEV is not set
 # CONFIG_INPUT_TSDEV is not set
-# CONFIG_INPUT_EVDEV is not set
+CONFIG_INPUT_EVDEV=y
 # CONFIG_INPUT_EVBUG is not set
 
 #
@@ -453,7 +491,13 @@
 # CONFIG_INPUT_KEYBOARD is not set
 # CONFIG_INPUT_MOUSE is not set
 # CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+CONFIG_TOUCHSCREEN_ADS7843_LH7=y
+CONFIG_HAS_TOUCHSCREEN_ADS7843_LH7=y
 # CONFIG_INPUT_MISC is not set
 
 #
@@ -461,7 +505,6 @@
 #
 # CONFIG_SERIO is not set
 # CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
 
 #
 # Character devices
@@ -479,6 +522,8 @@
 #
 # Non-8250 serial port support
 #
+# CONFIG_SERIAL_AMBA_PL010 is not set
+# CONFIG_SERIAL_AMBA_PL011 is not set
 CONFIG_SERIAL_CORE=y
 CONFIG_SERIAL_CORE_CONSOLE=y
 CONFIG_SERIAL_LH7A40X=y
@@ -510,7 +555,6 @@
 #
 # TPM devices
 #
-# CONFIG_TCG_TPM is not set
 
 #
 # I2C support
@@ -534,18 +578,73 @@
 #
 # Graphics support
 #
-# CONFIG_FB is not set
+CONFIG_FB=y
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+CONFIG_FB_SOFT_CURSOR=y
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+CONFIG_FB_ARMCLCD=y
+CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT=y
+# CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02 is not set
+# CONFIG_FB_ARMCLCD_SHARP_LQ64D343 is not set
+# CONFIG_FB_ARMCLCD_SHARP_LQ10D368 is not set
+# CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41 is not set
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_VIRTUAL is not set
 
 #
 # Console display driver support
 #
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_DUMMY_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE is not set
+
+#
+# Logo configuration
+#
+# CONFIG_LOGO is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
 
 #
 # Sound
 #
-# CONFIG_SOUND is not set
+CONFIG_SOUND=y
+
+#
+# Advanced Linux Sound Architecture
+#
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+# CONFIG_SND_SEQUENCER is not set
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=y
+CONFIG_SND_PCM_OSS=y
+# CONFIG_SND_RTCTIMER is not set
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+
+#
+# Generic devices
+#
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+CONFIG_SND_AC97_CODEC=y
+
+#
+# ALSA ARM devices
+#
+CONFIG_SND_LH7A40X_AC97=y
+
+#
+# Open Sound System
+#
+# CONFIG_SOUND_PRIME is not set
 
 #
 # USB support
diff --git a/arch/arm/configs/lpd7a404_defconfig b/arch/arm/configs/lpd7a404_defconfig
index 208d591..3a57be3 100644
--- a/arch/arm/configs/lpd7a404_defconfig
+++ b/arch/arm/configs/lpd7a404_defconfig
@@ -1,52 +1,58 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.12-rc1-bk2
-# Mon Mar 28 00:14:08 2005
+# Linux kernel version: 2.6.16
+# Thu Mar 23 17:50:31 2006
 #
 CONFIG_ARM=y
 CONFIG_MMU=y
-CONFIG_UID16=y
 CONFIG_RWSEM_GENERIC_SPINLOCK=y
 CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_GENERIC_IOMAP=y
 
 #
 # Code maturity level options
 #
 CONFIG_EXPERIMENTAL=y
-CONFIG_CLEAN_COMPILE=y
 CONFIG_BROKEN_ON_SMP=y
 CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
 
 #
 # General setup
 #
 CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 # CONFIG_POSIX_MQUEUE is not set
 # CONFIG_BSD_PROCESS_ACCT is not set
 CONFIG_SYSCTL=y
 # CONFIG_AUDIT is not set
-# CONFIG_HOTPLUG is not set
-CONFIG_KOBJECT_UEVENT=y
 CONFIG_IKCONFIG=y
 # CONFIG_IKCONFIG_PROC is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_UID16=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_EMBEDDED=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
+# CONFIG_HOTPLUG is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
 CONFIG_BASE_FULL=y
 CONFIG_FUTEX=y
 # CONFIG_EPOLL is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_SHMEM=y
 CONFIG_CC_ALIGN_FUNCTIONS=0
 CONFIG_CC_ALIGN_LABELS=0
 CONFIG_CC_ALIGN_LOOPS=0
 CONFIG_CC_ALIGN_JUMPS=0
+CONFIG_SLAB=y
 # CONFIG_TINY_SHMEM is not set
 CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
+CONFIG_OBSOLETE_INTERMODULE=y
 
 #
 # Loadable module support
@@ -54,6 +60,23 @@
 # CONFIG_MODULES is not set
 
 #
+# Block layer
+#
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+
+#
 # System Type
 #
 # CONFIG_ARCH_CLPS7500 is not set
@@ -71,11 +94,15 @@
 # CONFIG_ARCH_SA1100 is not set
 # CONFIG_ARCH_S3C2410 is not set
 # CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7952X is not set
 CONFIG_ARCH_LH7A40X=y
 # CONFIG_ARCH_OMAP is not set
 # CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_REALVIEW is not set
 # CONFIG_ARCH_IMX is not set
 # CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_AT91RM9200 is not set
 
 #
 # LH7A40X Implementations
@@ -110,6 +137,7 @@
 #
 # Bus support
 #
+CONFIG_ARM_AMBA=y
 
 #
 # PCCARD (PCMCIA/CardBus) support
@@ -120,7 +148,18 @@
 # Kernel Features
 #
 CONFIG_PREEMPT=y
+# CONFIG_NO_IDLE_HZ is not set
+# CONFIG_AEABI is not set
+CONFIG_ARCH_DISCONTIGMEM_ENABLE=y
+CONFIG_SELECT_MEMORY_MODEL=y
+# CONFIG_FLATMEM_MANUAL is not set
+CONFIG_DISCONTIGMEM_MANUAL=y
+# CONFIG_SPARSEMEM_MANUAL is not set
 CONFIG_DISCONTIGMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_NEED_MULTIPLE_NODES=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4096
 CONFIG_ALIGNMENT_TRAP=y
 
 #
@@ -154,6 +193,84 @@
 # Power management options
 #
 # CONFIG_PM is not set
+# CONFIG_APM is not set
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+# CONFIG_NETDEBUG is not set
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+# CONFIG_IPV6 is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
 
 #
 # Device Drivers
@@ -168,6 +285,11 @@
 # CONFIG_DEBUG_DRIVER is not set
 
 #
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
+#
 # Memory Technology Devices (MTD)
 #
 CONFIG_MTD=y
@@ -175,7 +297,7 @@
 # CONFIG_MTD_CONCAT is not set
 CONFIG_MTD_PARTITIONS=y
 # CONFIG_MTD_REDBOOT_PARTS is not set
-# CONFIG_MTD_CMDLINE_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
 # CONFIG_MTD_AFS_PARTS is not set
 
 #
@@ -186,6 +308,7 @@
 # CONFIG_FTL is not set
 # CONFIG_NFTL is not set
 # CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
 
 #
 # RAM/ROM/Flash chip drivers
@@ -211,15 +334,18 @@
 # CONFIG_MTD_RAM is not set
 # CONFIG_MTD_ROM is not set
 # CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_XIP is not set
+# CONFIG_MTD_OBSOLETE_CHIPS is not set
 
 #
 # Mapping drivers for chip access
 #
 # CONFIG_MTD_COMPLEX_MAPPINGS is not set
-# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_START=0x00000000
+CONFIG_MTD_PHYSMAP_LEN=0x04000000
+CONFIG_MTD_PHYSMAP_BANKWIDTH=4
 # CONFIG_MTD_ARM_INTEGRATOR is not set
-# CONFIG_MTD_EDB7312 is not set
+# CONFIG_MTD_PLATRAM is not set
 
 #
 # Self-contained MTD device drivers
@@ -243,6 +369,11 @@
 # CONFIG_MTD_NAND is not set
 
 #
+# OneNAND Flash Device Drivers
+#
+# CONFIG_MTD_ONENAND is not set
+
+#
 # Parallel port support
 #
 # CONFIG_PARPORT is not set
@@ -254,7 +385,6 @@
 #
 # Block devices
 #
-# CONFIG_BLK_DEV_FD is not set
 # CONFIG_BLK_DEV_COW_COMMON is not set
 CONFIG_BLK_DEV_LOOP=y
 # CONFIG_BLK_DEV_CRYPTOLOOP is not set
@@ -262,16 +392,7 @@
 # CONFIG_BLK_DEV_UB is not set
 # CONFIG_BLK_DEV_RAM is not set
 CONFIG_BLK_DEV_RAM_COUNT=16
-CONFIG_INITRAMFS_SOURCE=""
 # CONFIG_CDROM_PKTCDVD is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-# CONFIG_IOSCHED_AS is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-CONFIG_IOSCHED_CFQ=y
 # CONFIG_ATA_OVER_ETH is not set
 
 #
@@ -291,12 +412,13 @@
 # CONFIG_BLK_DEV_IDEFLOPPY is not set
 # CONFIG_BLK_DEV_IDESCSI is not set
 # CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_POLL=y
 
 #
 # IDE chipset support/bugfixes
 #
 CONFIG_IDE_GENERIC=y
-# CONFIG_IDE_ARM is not set
+CONFIG_IDE_ARM=y
 # CONFIG_BLK_DEV_IDEDMA is not set
 # CONFIG_IDEDMA_AUTO is not set
 # CONFIG_BLK_DEV_HD is not set
@@ -304,6 +426,7 @@
 #
 # SCSI device support
 #
+# CONFIG_RAID_ATTRS is not set
 CONFIG_SCSI=y
 # CONFIG_SCSI_PROC_FS is not set
 
@@ -315,6 +438,7 @@
 # CONFIG_CHR_DEV_OSST is not set
 # CONFIG_BLK_DEV_SR is not set
 # CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
 
 #
 # Some SCSI devices (e.g. CD jukebox) support multiple LUNs
@@ -329,10 +453,12 @@
 # CONFIG_SCSI_SPI_ATTRS is not set
 # CONFIG_SCSI_FC_ATTRS is not set
 # CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_ATTRS is not set
 
 #
 # SCSI low-level drivers
 #
+# CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_SATA is not set
 # CONFIG_SCSI_DEBUG is not set
 
@@ -344,6 +470,7 @@
 #
 # Fusion MPT device support
 #
+# CONFIG_FUSION is not set
 
 #
 # IEEE 1394 (FireWire) support
@@ -354,70 +481,8 @@
 #
 
 #
-# Networking support
+# Network device support
 #
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-# CONFIG_NETLINK_DEV is not set
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_TUNNEL is not set
-# CONFIG_IP_TCPDIAG is not set
-# CONFIG_IP_TCPDIAG_IPV6 is not set
-# CONFIG_IPV6 is not set
-# CONFIG_NETFILTER is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_SCTP is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-# CONFIG_NET_CLS_ROUTE is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
 CONFIG_NETDEVICES=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
@@ -425,11 +490,17 @@
 # CONFIG_TUN is not set
 
 #
+# PHY device support
+#
+# CONFIG_PHYLIB is not set
+
+#
 # Ethernet (10 or 100Mbit)
 #
 CONFIG_NET_ETHERNET=y
 CONFIG_MII=y
 CONFIG_SMC91X=y
+# CONFIG_DM9000 is not set
 
 #
 # Ethernet (1000 Mbit)
@@ -456,6 +527,8 @@
 # CONFIG_SLIP is not set
 # CONFIG_SHAPER is not set
 # CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
 
 #
 # ISDN subsystem
@@ -470,10 +543,13 @@
 #
 # Userland interfaces
 #
-# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
 # CONFIG_INPUT_JOYDEV is not set
 # CONFIG_INPUT_TSDEV is not set
-# CONFIG_INPUT_EVDEV is not set
+CONFIG_INPUT_EVDEV=y
 # CONFIG_INPUT_EVBUG is not set
 
 #
@@ -482,7 +558,13 @@
 # CONFIG_INPUT_KEYBOARD is not set
 # CONFIG_INPUT_MOUSE is not set
 # CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+CONFIG_TOUCHSCREEN_ADC_LH7=y
+CONFIG_HAS_TOUCHSCREEN_ADC_LH7=y
 # CONFIG_INPUT_MISC is not set
 
 #
@@ -490,7 +572,6 @@
 #
 # CONFIG_SERIO is not set
 # CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
 
 #
 # Character devices
@@ -508,6 +589,8 @@
 #
 # Non-8250 serial port support
 #
+# CONFIG_SERIAL_AMBA_PL010 is not set
+# CONFIG_SERIAL_AMBA_PL011 is not set
 CONFIG_SERIAL_CORE=y
 CONFIG_SERIAL_CORE_CONSOLE=y
 CONFIG_SERIAL_LH7A40X=y
@@ -533,13 +616,13 @@
 #
 # Ftape, the floppy tape device driver
 #
-# CONFIG_DRM is not set
 # CONFIG_RAW_DRIVER is not set
 
 #
 # TPM devices
 #
 # CONFIG_TCG_TPM is not set
+# CONFIG_TELCLOCK is not set
 
 #
 # I2C support
@@ -547,10 +630,33 @@
 # CONFIG_I2C is not set
 
 #
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
 # Misc devices
 #
 
 #
+# Multimedia Capabilities Port drivers
+#
+
+#
 # Multimedia devices
 #
 # CONFIG_VIDEO_DEV is not set
@@ -563,18 +669,83 @@
 #
 # Graphics support
 #
-# CONFIG_FB is not set
+CONFIG_FB=y
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+CONFIG_FB_ARMCLCD=y
+CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT=y
+# CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02 is not set
+# CONFIG_FB_ARMCLCD_SHARP_LQ64D343 is not set
+# CONFIG_FB_ARMCLCD_SHARP_LQ10D368 is not set
+# CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41 is not set
+# CONFIG_FB_ARMCLCD_AUO_A070VW01_WIDE is not set
+# CONFIG_FB_ARMCLCD_HITACHI is not set
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_VIRTUAL is not set
 
 #
 # Console display driver support
 #
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_DUMMY_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE is not set
+
+#
+# Logo configuration
+#
+# CONFIG_LOGO is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
 
 #
 # Sound
 #
-# CONFIG_SOUND is not set
+CONFIG_SOUND=y
+
+#
+# Advanced Linux Sound Architecture
+#
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+# CONFIG_SND_SEQUENCER is not set
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=y
+CONFIG_SND_PCM_OSS=y
+# CONFIG_SND_RTCTIMER is not set
+# CONFIG_SND_DYNAMIC_MINORS is not set
+CONFIG_SND_SUPPORT_OLD_API=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+
+#
+# Generic devices
+#
+CONFIG_SND_AC97_CODEC=y
+CONFIG_SND_AC97_BUS=y
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+
+#
+# ALSA ARM devices
+#
+# CONFIG_SND_ARMAACI is not set
+CONFIG_SND_LH7A40X_AC97=y
+
+#
+# USB devices
+#
+# CONFIG_SND_USB_AUDIO is not set
+
+#
+# Open Sound System
+#
+# CONFIG_SOUND_PRIME is not set
 
 #
 # USB support
@@ -595,6 +766,7 @@
 #
 # USB Host Controller Drivers
 #
+# CONFIG_USB_ISP116X_HCD is not set
 CONFIG_USB_OHCI_HCD=y
 # CONFIG_USB_OHCI_BIG_ENDIAN is not set
 CONFIG_USB_OHCI_LITTLE_ENDIAN=y
@@ -603,16 +775,19 @@
 #
 # USB Device Class drivers
 #
-# CONFIG_USB_BLUETOOTH_TTY is not set
+# CONFIG_OBSOLETE_OSS_USB_DRIVER is not set
 # CONFIG_USB_ACM is not set
 # CONFIG_USB_PRINTER is not set
 
 #
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# may also be needed; see USB_STORAGE Help for more information
 #
 CONFIG_USB_STORAGE=y
 CONFIG_USB_STORAGE_DEBUG=y
-# CONFIG_USB_STORAGE_RW_DETECT is not set
 CONFIG_USB_STORAGE_DATAFAB=y
 # CONFIG_USB_STORAGE_FREECOM is not set
 # CONFIG_USB_STORAGE_ISD200 is not set
@@ -621,22 +796,32 @@
 # CONFIG_USB_STORAGE_SDDR09 is not set
 # CONFIG_USB_STORAGE_SDDR55 is not set
 # CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
+# CONFIG_USB_LIBUSUAL is not set
 
 #
 # USB Input Devices
 #
 CONFIG_USB_HID=y
 CONFIG_USB_HIDINPUT=y
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
 # CONFIG_HID_FF is not set
 # CONFIG_USB_HIDDEV is not set
 # CONFIG_USB_AIPTEK is not set
 # CONFIG_USB_WACOM is not set
+# CONFIG_USB_ACECAD is not set
 # CONFIG_USB_KBTAB is not set
 # CONFIG_USB_POWERMATE is not set
 # CONFIG_USB_MTOUCH is not set
+# CONFIG_USB_ITMTOUCH is not set
 # CONFIG_USB_EGALAX is not set
+# CONFIG_USB_YEALINK is not set
 # CONFIG_USB_XPAD is not set
 # CONFIG_USB_ATI_REMOTE is not set
+# CONFIG_USB_ATI_REMOTE2 is not set
+# CONFIG_USB_KEYSPAN_REMOTE is not set
+# CONFIG_USB_APPLETOUCH is not set
 
 #
 # USB Imaging devices
@@ -686,16 +871,33 @@
 # CONFIG_USB_PHIDGETKIT is not set
 # CONFIG_USB_PHIDGETSERVO is not set
 # CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_LD is not set
 # CONFIG_USB_TEST is not set
 
 #
-# USB ATM/DSL drivers
+# USB DSL modem support
 #
 
 #
 # USB Gadget Support
 #
-# CONFIG_USB_GADGET is not set
+CONFIG_USB_GADGET=y
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_PXA2XX is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+CONFIG_USB_GADGET_LH7=y
+CONFIG_USB_LH7=y
+# CONFIG_USB_GADGET_OMAP is not set
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+# CONFIG_USB_GADGET_DUALSPEED is not set
+CONFIG_USB_ZERO=y
+# CONFIG_USB_ETH is not set
+# CONFIG_USB_GADGETFS is not set
+# CONFIG_USB_FILE_STORAGE is not set
+# CONFIG_USB_G_SERIAL is not set
 
 #
 # MMC/SD Card support
@@ -707,6 +909,7 @@
 #
 CONFIG_EXT2_FS=y
 # CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
 CONFIG_EXT3_FS=y
 CONFIG_EXT3_FS_XATTR=y
 # CONFIG_EXT3_FS_POSIX_ACL is not set
@@ -716,17 +919,17 @@
 CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
-
-#
-# XFS support
-#
+# CONFIG_FS_POSIX_ACL is not set
 # CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
 # CONFIG_MINIX_FS is not set
 # CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
 # CONFIG_QUOTA is not set
 CONFIG_DNOTIFY=y
 # CONFIG_AUTOFS_FS is not set
 # CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
 
 #
 # CD-ROM/DVD Filesystems
@@ -749,12 +952,11 @@
 #
 CONFIG_PROC_FS=y
 CONFIG_SYSFS=y
-# CONFIG_DEVFS_FS is not set
-# CONFIG_DEVPTS_FS_XATTR is not set
 CONFIG_TMPFS=y
-# CONFIG_TMPFS_XATTR is not set
 # CONFIG_HUGETLB_PAGE is not set
 CONFIG_RAMFS=y
+# CONFIG_RELAYFS_FS is not set
+# CONFIG_CONFIGFS_FS is not set
 
 #
 # Miscellaneous filesystems
@@ -769,8 +971,8 @@
 # CONFIG_JFFS_FS is not set
 CONFIG_JFFS2_FS=y
 CONFIG_JFFS2_FS_DEBUG=0
-# CONFIG_JFFS2_FS_NAND is not set
-# CONFIG_JFFS2_FS_NOR_ECC is not set
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_SUMMARY is not set
 # CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
 CONFIG_JFFS2_ZLIB=y
 CONFIG_JFFS2_RTIME=y
@@ -787,12 +989,14 @@
 #
 CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
 # CONFIG_NFS_V4 is not set
 # CONFIG_NFS_DIRECTIO is not set
 # CONFIG_NFSD is not set
 CONFIG_ROOT_NFS=y
 CONFIG_LOCKD=y
 CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
 CONFIG_SUNRPC=y
 # CONFIG_RPCSEC_GSS_KRB5 is not set
 # CONFIG_RPCSEC_GSS_SPKM3 is not set
@@ -801,6 +1005,7 @@
 # CONFIG_NCP_FS is not set
 # CONFIG_CODA_FS is not set
 # CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
 
 #
 # Partition Types
@@ -820,6 +1025,7 @@
 # CONFIG_SGI_PARTITION is not set
 # CONFIG_ULTRIX_PARTITION is not set
 # CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
 # CONFIG_EFI_PARTITION is not set
 
 #
@@ -875,19 +1081,24 @@
 # Kernel hacking
 #
 # CONFIG_PRINTK_TIME is not set
-CONFIG_DEBUG_KERNEL=y
 CONFIG_MAGIC_SYSRQ=y
-CONFIG_LOG_BUF_SHIFT=14
+CONFIG_DEBUG_KERNEL=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_DETECT_SOFTLOCKUP=y
 # CONFIG_SCHEDSTATS is not set
 # CONFIG_DEBUG_SLAB is not set
 CONFIG_DEBUG_PREEMPT=y
+CONFIG_DEBUG_MUTEXES=y
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_KOBJECT is not set
 CONFIG_DEBUG_BUGVERBOSE=y
 CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_FS is not set
+# CONFIG_DEBUG_VM is not set
 CONFIG_FRAME_POINTER=y
+CONFIG_FORCED_INLINING=y
+# CONFIG_RCU_TORTURE_TEST is not set
 CONFIG_DEBUG_USER=y
 # CONFIG_DEBUG_WAITQ is not set
 CONFIG_DEBUG_ERRORS=y
@@ -912,6 +1123,7 @@
 # Library routines
 #
 # CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
 CONFIG_CRC32=y
 # CONFIG_LIBCRC32C is not set
 CONFIG_ZLIB_INFLATE=y
diff --git a/arch/arm/configs/pnx4008_defconfig b/arch/arm/configs/pnx4008_defconfig
new file mode 100644
index 0000000..8a078d4
--- /dev/null
+++ b/arch/arm/configs/pnx4008_defconfig
@@ -0,0 +1,2072 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.17-rc1
+# Thu Apr  6 17:05:58 2006
+#
+CONFIG_ARM=y
+CONFIG_MMU=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_VECTORS_BASE=0xffff0000
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
+CONFIG_SYSCTL=y
+CONFIG_AUDIT=y
+# CONFIG_IKCONFIG is not set
+# CONFIG_RELAY is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_UID16=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_EMBEDDED=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SHMEM=y
+CONFIG_SLAB=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
+CONFIG_OBSOLETE_INTERMODULE=m
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_KMOD=y
+
+#
+# Block layer
+#
+# CONFIG_BLK_DEV_IO_TRACE is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# System Type
+#
+# CONFIG_ARCH_CLPS7500 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_CO285 is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_IOP3XX is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_OMAP is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_AT91RM9200 is not set
+CONFIG_ARCH_PNX4008=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_ARM926T=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5TJ=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_V4WB=y
+CONFIG_CPU_TLB_V4WBI=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
+# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
+
+#
+# Bus support
+#
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+CONFIG_PCCARD=m
+# CONFIG_PCMCIA_DEBUG is not set
+CONFIG_PCMCIA=m
+CONFIG_PCMCIA_LOAD_CIS=y
+CONFIG_PCMCIA_IOCTL=y
+
+#
+# PC-card bridges
+#
+
+#
+# Kernel Features
+#
+CONFIG_PREEMPT=y
+# CONFIG_NO_IDLE_HZ is not set
+CONFIG_HZ=100
+# CONFIG_AEABI is not set
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+CONFIG_ALIGNMENT_TRAP=y
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0
+CONFIG_ZBOOT_ROM_BSS=0
+CONFIG_CMDLINE="mem=64M console=ttyS0,115200"
+# CONFIG_XIP_KERNEL is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+# CONFIG_FPE_NWFPE is not set
+# CONFIG_FPE_FASTFPE is not set
+# CONFIG_VFP is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_AOUT=m
+CONFIG_BINFMT_MISC=m
+# CONFIG_ARTHUR is not set
+
+#
+# Power management options
+#
+CONFIG_PM=y
+CONFIG_PM_LEGACY=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_APM=m
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+# CONFIG_NETDEBUG is not set
+CONFIG_PACKET=m
+CONFIG_PACKET_MMAP=y
+CONFIG_UNIX=m
+CONFIG_XFRM=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=m
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_ASK_IP_FIB_HASH=y
+# CONFIG_IP_FIB_TRIE is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_FWMARK=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+# CONFIG_IP_ROUTE_MULTIPATH_CACHED is not set
+CONFIG_IP_ROUTE_VERBOSE=y
+# CONFIG_IP_PNP is not set
+CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE=m
+CONFIG_NET_IPGRE_BROADCAST=y
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET_XFRM_TUNNEL=m
+CONFIG_INET_TUNNEL=m
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+
+#
+# IP: Virtual Server Configuration
+#
+CONFIG_IP_VS=m
+# CONFIG_IP_VS_DEBUG is not set
+CONFIG_IP_VS_TAB_BITS=12
+
+#
+# IPVS transport protocol load balancing support
+#
+CONFIG_IP_VS_PROTO_TCP=y
+CONFIG_IP_VS_PROTO_UDP=y
+CONFIG_IP_VS_PROTO_ESP=y
+CONFIG_IP_VS_PROTO_AH=y
+
+#
+# IPVS scheduler
+#
+CONFIG_IP_VS_RR=m
+CONFIG_IP_VS_WRR=m
+CONFIG_IP_VS_LC=m
+CONFIG_IP_VS_WLC=m
+CONFIG_IP_VS_LBLC=m
+CONFIG_IP_VS_LBLCR=m
+CONFIG_IP_VS_DH=m
+CONFIG_IP_VS_SH=m
+CONFIG_IP_VS_SED=m
+CONFIG_IP_VS_NQ=m
+
+#
+# IPVS application helper
+#
+CONFIG_IP_VS_FTP=m
+CONFIG_IPV6=m
+CONFIG_IPV6_PRIVACY=y
+# CONFIG_IPV6_ROUTER_PREF is not set
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_INET6_XFRM_TUNNEL=m
+CONFIG_INET6_TUNNEL=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+CONFIG_BRIDGE_NETFILTER=y
+
+#
+# Core Netfilter Configuration
+#
+# CONFIG_NETFILTER_NETLINK is not set
+# CONFIG_NETFILTER_XTABLES is not set
+
+#
+# IP: Netfilter Configuration
+#
+CONFIG_IP_NF_CONNTRACK=m
+CONFIG_IP_NF_CT_ACCT=y
+CONFIG_IP_NF_CONNTRACK_MARK=y
+# CONFIG_IP_NF_CONNTRACK_EVENTS is not set
+CONFIG_IP_NF_CT_PROTO_SCTP=m
+CONFIG_IP_NF_FTP=m
+CONFIG_IP_NF_IRC=m
+# CONFIG_IP_NF_NETBIOS_NS is not set
+CONFIG_IP_NF_TFTP=m
+CONFIG_IP_NF_AMANDA=m
+# CONFIG_IP_NF_PPTP is not set
+# CONFIG_IP_NF_H323 is not set
+CONFIG_IP_NF_QUEUE=m
+
+#
+# IPv6: Netfilter Configuration (EXPERIMENTAL)
+#
+CONFIG_IP6_NF_QUEUE=m
+
+#
+# DECnet: Netfilter Configuration
+#
+CONFIG_DECNET_NF_GRABULATOR=m
+
+#
+# Bridge: Netfilter Configuration
+#
+CONFIG_BRIDGE_NF_EBTABLES=m
+CONFIG_BRIDGE_EBT_BROUTE=m
+CONFIG_BRIDGE_EBT_T_FILTER=m
+CONFIG_BRIDGE_EBT_T_NAT=m
+CONFIG_BRIDGE_EBT_802_3=m
+CONFIG_BRIDGE_EBT_AMONG=m
+CONFIG_BRIDGE_EBT_ARP=m
+CONFIG_BRIDGE_EBT_IP=m
+CONFIG_BRIDGE_EBT_LIMIT=m
+CONFIG_BRIDGE_EBT_MARK=m
+CONFIG_BRIDGE_EBT_PKTTYPE=m
+CONFIG_BRIDGE_EBT_STP=m
+CONFIG_BRIDGE_EBT_VLAN=m
+CONFIG_BRIDGE_EBT_ARPREPLY=m
+CONFIG_BRIDGE_EBT_DNAT=m
+CONFIG_BRIDGE_EBT_MARK_T=m
+CONFIG_BRIDGE_EBT_REDIRECT=m
+CONFIG_BRIDGE_EBT_SNAT=m
+CONFIG_BRIDGE_EBT_LOG=m
+# CONFIG_BRIDGE_EBT_ULOG is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+CONFIG_IP_SCTP=m
+# CONFIG_SCTP_DBG_MSG is not set
+# CONFIG_SCTP_DBG_OBJCNT is not set
+# CONFIG_SCTP_HMAC_NONE is not set
+# CONFIG_SCTP_HMAC_SHA1 is not set
+CONFIG_SCTP_HMAC_MD5=y
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
+CONFIG_ATM=y
+CONFIG_ATM_CLIP=y
+# CONFIG_ATM_CLIP_NO_ICMP is not set
+CONFIG_ATM_LANE=m
+CONFIG_ATM_MPOA=m
+CONFIG_ATM_BR2684=m
+# CONFIG_ATM_BR2684_IPFILTER is not set
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_DECNET=m
+# CONFIG_DECNET_ROUTER is not set
+CONFIG_LLC=m
+CONFIG_LLC2=m
+CONFIG_IPX=m
+# CONFIG_IPX_INTERN is not set
+CONFIG_ATALK=m
+CONFIG_DEV_APPLETALK=y
+CONFIG_IPDDP=m
+CONFIG_IPDDP_ENCAP=y
+CONFIG_IPDDP_DECAP=y
+CONFIG_X25=m
+CONFIG_LAPB=m
+# CONFIG_NET_DIVERT is not set
+CONFIG_ECONET=m
+CONFIG_ECONET_AUNUDP=y
+CONFIG_ECONET_NATIVE=y
+CONFIG_WAN_ROUTER=m
+
+#
+# QoS and/or fair queueing
+#
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CLK_JIFFIES=y
+# CONFIG_NET_SCH_CLK_GETTIMEOFDAY is not set
+# CONFIG_NET_SCH_CLK_CPU is not set
+
+#
+# Queueing/Scheduling
+#
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_ATM=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+
+#
+# Classification
+#
+CONFIG_NET_CLS=y
+# CONFIG_NET_CLS_BASIC is not set
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_ROUTE=y
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+# CONFIG_CLS_U32_PERF is not set
+# CONFIG_CLS_U32_MARK is not set
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+# CONFIG_NET_EMATCH is not set
+# CONFIG_NET_CLS_ACT is not set
+CONFIG_NET_CLS_POLICE=y
+# CONFIG_NET_CLS_IND is not set
+CONFIG_NET_ESTIMATOR=y
+
+#
+# Network testing
+#
+CONFIG_NET_PKTGEN=m
+CONFIG_HAMRADIO=y
+
+#
+# Packet Radio protocols
+#
+CONFIG_AX25=m
+# CONFIG_AX25_DAMA_SLAVE is not set
+CONFIG_NETROM=m
+CONFIG_ROSE=m
+
+#
+# AX.25 network device drivers
+#
+CONFIG_MKISS=m
+CONFIG_6PACK=m
+CONFIG_BPQETHER=m
+CONFIG_BAYCOM_SER_FDX=m
+CONFIG_BAYCOM_SER_HDX=m
+CONFIG_BAYCOM_PAR=m
+CONFIG_BAYCOM_EPP=m
+CONFIG_YAM=m
+CONFIG_IRDA=m
+
+#
+# IrDA protocols
+#
+CONFIG_IRLAN=m
+CONFIG_IRNET=m
+CONFIG_IRCOMM=m
+# CONFIG_IRDA_ULTRA is not set
+
+#
+# IrDA options
+#
+CONFIG_IRDA_CACHE_LAST_LSAP=y
+CONFIG_IRDA_FAST_RR=y
+CONFIG_IRDA_DEBUG=y
+
+#
+# Infrared-port device drivers
+#
+
+#
+# SIR device drivers
+#
+CONFIG_IRTTY_SIR=m
+
+#
+# Dongle support
+#
+CONFIG_DONGLE=y
+CONFIG_ESI_DONGLE=m
+CONFIG_ACTISYS_DONGLE=m
+CONFIG_TEKRAM_DONGLE=m
+# CONFIG_TOIM3232_DONGLE is not set
+CONFIG_LITELINK_DONGLE=m
+CONFIG_MA600_DONGLE=m
+CONFIG_GIRBIL_DONGLE=m
+CONFIG_MCP2120_DONGLE=m
+CONFIG_OLD_BELKIN_DONGLE=m
+CONFIG_ACT200L_DONGLE=m
+
+#
+# Old SIR device drivers
+#
+CONFIG_IRPORT_SIR=m
+
+#
+# Old Serial dongle support
+#
+# CONFIG_DONGLE_OLD is not set
+
+#
+# FIR device drivers
+#
+CONFIG_USB_IRDA=m
+CONFIG_SIGMATEL_FIR=m
+CONFIG_BT=m
+CONFIG_BT_L2CAP=m
+CONFIG_BT_SCO=m
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=m
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_CMTP=m
+CONFIG_BT_HIDP=m
+
+#
+# Bluetooth device drivers
+#
+CONFIG_BT_HCIUSB=m
+CONFIG_BT_HCIUSB_SCO=y
+CONFIG_BT_HCIUART=m
+CONFIG_BT_HCIUART_H4=y
+CONFIG_BT_HCIUART_BCSP=y
+CONFIG_BT_HCIBCM203X=m
+# CONFIG_BT_HCIBPA10X is not set
+CONFIG_BT_HCIBFUSB=m
+CONFIG_BT_HCIDTL1=m
+CONFIG_BT_HCIBT3C=m
+CONFIG_BT_HCIBLUECARD=m
+CONFIG_BT_HCIBTUART=m
+CONFIG_BT_HCIVHCI=m
+CONFIG_IEEE80211=m
+# CONFIG_IEEE80211_DEBUG is not set
+# CONFIG_IEEE80211_CRYPT_WEP is not set
+CONFIG_IEEE80211_CRYPT_CCMP=m
+CONFIG_IEEE80211_CRYPT_TKIP=m
+# CONFIG_IEEE80211_SOFTMAC is not set
+CONFIG_WIRELESS_EXT=y
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=m
+# CONFIG_DEBUG_DRIVER is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+CONFIG_MTD=m
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=m
+CONFIG_MTD_PARTITIONS=y
+CONFIG_MTD_REDBOOT_PARTS=m
+CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
+# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
+# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=m
+CONFIG_MTD_BLOCK=m
+CONFIG_MTD_BLOCK_RO=m
+CONFIG_FTL=m
+CONFIG_NFTL=m
+CONFIG_NFTL_RW=y
+CONFIG_INFTL=m
+# CONFIG_RFD_FTL is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=m
+CONFIG_MTD_JEDECPROBE=m
+CONFIG_MTD_GEN_PROBE=m
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=m
+CONFIG_MTD_CFI_AMDSTD=m
+CONFIG_MTD_CFI_STAA=m
+CONFIG_MTD_CFI_UTIL=m
+CONFIG_MTD_RAM=m
+CONFIG_MTD_ROM=m
+CONFIG_MTD_ABSENT=m
+# CONFIG_MTD_OBSOLETE_CHIPS is not set
+
+#
+# Mapping drivers for chip access
+#
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=m
+CONFIG_MTD_PHYSMAP_START=0x8000000
+CONFIG_MTD_PHYSMAP_LEN=0x4000000
+CONFIG_MTD_PHYSMAP_BANKWIDTH=2
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+# CONFIG_MTD_IMPA7 is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+CONFIG_MTD_SLRAM=m
+CONFIG_MTD_PHRAM=m
+CONFIG_MTD_MTDRAM=m
+CONFIG_MTDRAM_TOTAL_SIZE=4096
+CONFIG_MTDRAM_ERASE_SIZE=128
+CONFIG_MTD_BLKMTD=m
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+CONFIG_MTD_DOC2000=m
+CONFIG_MTD_DOC2001=m
+CONFIG_MTD_DOC2001PLUS=m
+CONFIG_MTD_DOCPROBE=m
+CONFIG_MTD_DOCECC=m
+# CONFIG_MTD_DOCPROBE_ADVANCED is not set
+CONFIG_MTD_DOCPROBE_ADDRESS=0
+
+#
+# NAND Flash Device Drivers
+#
+CONFIG_MTD_NAND=m
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+CONFIG_MTD_NAND_IDS=m
+CONFIG_MTD_NAND_DISKONCHIP=m
+# CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED is not set
+CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0
+# CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+
+#
+# OneNAND Flash Device Drivers
+#
+# CONFIG_MTD_ONENAND is not set
+
+#
+# Parallel port support
+#
+CONFIG_PARPORT=m
+CONFIG_PARPORT_PC=m
+CONFIG_PARPORT_PC_FIFO=y
+# CONFIG_PARPORT_PC_SUPERIO is not set
+CONFIG_PARPORT_PC_PCMCIA=m
+CONFIG_PARPORT_NOT_PC=y
+# CONFIG_PARPORT_ARC is not set
+# CONFIG_PARPORT_GSC is not set
+CONFIG_PARPORT_1284=y
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+CONFIG_PARIDE=m
+CONFIG_PARIDE_PARPORT=m
+
+#
+# Parallel IDE high-level drivers
+#
+CONFIG_PARIDE_PD=m
+CONFIG_PARIDE_PCD=m
+CONFIG_PARIDE_PF=m
+CONFIG_PARIDE_PT=m
+CONFIG_PARIDE_PG=m
+
+#
+# Parallel IDE protocol modules
+#
+CONFIG_PARIDE_ATEN=m
+CONFIG_PARIDE_BPCK=m
+CONFIG_PARIDE_BPCK6=m
+CONFIG_PARIDE_COMM=m
+CONFIG_PARIDE_DSTR=m
+CONFIG_PARIDE_FIT2=m
+CONFIG_PARIDE_FIT3=m
+CONFIG_PARIDE_EPAT=m
+# CONFIG_PARIDE_EPATC8 is not set
+CONFIG_PARIDE_EPIA=m
+CONFIG_PARIDE_FRIQ=m
+CONFIG_PARIDE_FRPW=m
+CONFIG_PARIDE_KBIC=m
+CONFIG_PARIDE_KTTI=m
+CONFIG_PARIDE_ON20=m
+CONFIG_PARIDE_ON26=m
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_NBD=m
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_CDROM_PKTCDVD_BUFFERS=8
+# CONFIG_CDROM_PKTCDVD_WCACHE is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+CONFIG_IDE=m
+CONFIG_BLK_DEV_IDE=m
+
+#
+# Please see Documentation/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_IDE_SATA is not set
+CONFIG_BLK_DEV_IDEDISK=m
+# CONFIG_IDEDISK_MULTI_MODE is not set
+CONFIG_BLK_DEV_IDECS=m
+CONFIG_BLK_DEV_IDECD=m
+CONFIG_BLK_DEV_IDETAPE=m
+CONFIG_BLK_DEV_IDEFLOPPY=m
+CONFIG_BLK_DEV_IDESCSI=m
+# CONFIG_IDE_TASK_IOCTL is not set
+
+#
+# IDE chipset support/bugfixes
+#
+CONFIG_IDE_GENERIC=m
+# CONFIG_IDE_ARM is not set
+# CONFIG_BLK_DEV_IDEDMA is not set
+# CONFIG_IDEDMA_AUTO is not set
+# CONFIG_BLK_DEV_HD is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=m
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=m
+CONFIG_CHR_DEV_ST=m
+CONFIG_CHR_DEV_OSST=m
+CONFIG_BLK_DEV_SR=m
+# CONFIG_BLK_DEV_SR_VENDOR is not set
+CONFIG_CHR_DEV_SG=m
+CONFIG_CHR_DEV_SCH=m
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+CONFIG_SCSI_MULTI_LUN=y
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_LOGGING=y
+
+#
+# SCSI Transport Attributes
+#
+CONFIG_SCSI_SPI_ATTRS=m
+CONFIG_SCSI_FC_ATTRS=m
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_ATTRS is not set
+
+#
+# SCSI low-level drivers
+#
+# CONFIG_ISCSI_TCP is not set
+CONFIG_SCSI_SATA=m
+CONFIG_SCSI_PPA=m
+CONFIG_SCSI_IMM=m
+# CONFIG_SCSI_IZIP_EPP16 is not set
+# CONFIG_SCSI_IZIP_SLOW_CTR is not set
+CONFIG_SCSI_DEBUG=m
+
+#
+# PCMCIA SCSI adapter support
+#
+CONFIG_PCMCIA_AHA152X=m
+CONFIG_PCMCIA_FDOMAIN=m
+CONFIG_PCMCIA_NINJA_SCSI=m
+CONFIG_PCMCIA_QLOGIC=m
+CONFIG_PCMCIA_SYM53C500=m
+
+#
+# Multi-device support (RAID and LVM)
+#
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+CONFIG_MD_RAID10=m
+CONFIG_MD_RAID5=m
+# CONFIG_MD_RAID5_RESHAPE is not set
+CONFIG_MD_RAID6=m
+CONFIG_MD_MULTIPATH=m
+CONFIG_MD_FAULTY=m
+CONFIG_BLK_DEV_DM=m
+CONFIG_DM_CRYPT=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+CONFIG_DM_ZERO=m
+# CONFIG_DM_MULTIPATH is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+
+#
+# I2O device support
+#
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+CONFIG_DUMMY=m
+CONFIG_BONDING=m
+CONFIG_EQUALIZER=m
+CONFIG_TUN=m
+
+#
+# PHY device support
+#
+# CONFIG_PHYLIB is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=m
+# CONFIG_SMC91X is not set
+# CONFIG_DM9000 is not set
+CONFIG_NET_POCKET=y
+CONFIG_DE600=m
+CONFIG_DE620=m
+
+#
+# Ethernet (1000 Mbit)
+#
+
+#
+# Ethernet (10000 Mbit)
+#
+
+#
+# Token Ring devices
+#
+
+#
+# Wireless LAN (non-hamradio)
+#
+CONFIG_NET_RADIO=y
+# CONFIG_NET_WIRELESS_RTNETLINK is not set
+
+#
+# Obsolete Wireless cards support (pre-802.11)
+#
+CONFIG_STRIP=m
+CONFIG_PCMCIA_WAVELAN=m
+CONFIG_PCMCIA_NETWAVE=m
+
+#
+# Wireless 802.11 Frequency Hopping cards support
+#
+CONFIG_PCMCIA_RAYCS=m
+
+#
+# Wireless 802.11b ISA/PCI cards support
+#
+CONFIG_HERMES=m
+CONFIG_ATMEL=m
+
+#
+# Wireless 802.11b Pcmcia/Cardbus cards support
+#
+CONFIG_PCMCIA_HERMES=m
+# CONFIG_PCMCIA_SPECTRUM is not set
+CONFIG_AIRO_CS=m
+CONFIG_PCMCIA_ATMEL=m
+CONFIG_PCMCIA_WL3501=m
+# CONFIG_HOSTAP is not set
+CONFIG_NET_WIRELESS=y
+
+#
+# PCMCIA network device support
+#
+CONFIG_NET_PCMCIA=y
+CONFIG_PCMCIA_3C589=m
+CONFIG_PCMCIA_3C574=m
+CONFIG_PCMCIA_FMVJ18X=m
+CONFIG_PCMCIA_PCNET=m
+CONFIG_PCMCIA_NMCLAN=m
+CONFIG_PCMCIA_SMC91C92=m
+CONFIG_PCMCIA_XIRC2PS=m
+CONFIG_PCMCIA_AXNET=m
+
+#
+# Wan interfaces
+#
+CONFIG_WAN=y
+CONFIG_SYNCLINK_SYNCPPP=m
+CONFIG_HDLC=m
+CONFIG_HDLC_RAW=y
+CONFIG_HDLC_RAW_ETH=y
+CONFIG_HDLC_CISCO=y
+CONFIG_HDLC_FR=y
+CONFIG_HDLC_PPP=y
+CONFIG_HDLC_X25=y
+CONFIG_DLCI=m
+CONFIG_DLCI_COUNT=24
+CONFIG_DLCI_MAX=8
+CONFIG_WAN_ROUTER_DRIVERS=y
+CONFIG_LAPBETHER=m
+CONFIG_X25_ASY=m
+
+#
+# ATM drivers
+#
+# CONFIG_ATM_DUMMY is not set
+CONFIG_ATM_TCP=m
+CONFIG_PLIP=m
+CONFIG_PPP=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_MPPE=m
+CONFIG_PPPOE=m
+CONFIG_PPPOATM=m
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+CONFIG_SLIP_SMART=y
+CONFIG_SLIP_MODE_SLIP6=y
+CONFIG_SHAPER=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETPOLL=y
+# CONFIG_NETPOLL_RX is not set
+# CONFIG_NETPOLL_TRAP is not set
+CONFIG_NET_POLL_CONTROLLER=y
+
+#
+# ISDN subsystem
+#
+CONFIG_ISDN=m
+
+#
+# Old ISDN4Linux
+#
+CONFIG_ISDN_I4L=m
+CONFIG_ISDN_PPP=y
+CONFIG_ISDN_PPP_VJ=y
+CONFIG_ISDN_MPP=y
+CONFIG_IPPP_FILTER=y
+CONFIG_ISDN_PPP_BSDCOMP=m
+CONFIG_ISDN_AUDIO=y
+CONFIG_ISDN_TTY_FAX=y
+CONFIG_ISDN_X25=y
+
+#
+# ISDN feature submodules
+#
+CONFIG_ISDN_DRV_LOOP=m
+CONFIG_ISDN_DIVERSION=m
+
+#
+# ISDN4Linux hardware drivers
+#
+
+#
+# Passive cards
+#
+CONFIG_ISDN_DRV_HISAX=m
+
+#
+# D-channel protocol features
+#
+CONFIG_HISAX_EURO=y
+CONFIG_DE_AOC=y
+# CONFIG_HISAX_NO_SENDCOMPLETE is not set
+# CONFIG_HISAX_NO_LLC is not set
+# CONFIG_HISAX_NO_KEYPAD is not set
+CONFIG_HISAX_1TR6=y
+CONFIG_HISAX_NI1=y
+CONFIG_HISAX_MAX_CARDS=8
+
+#
+# HiSax supported cards
+#
+CONFIG_HISAX_16_3=y
+CONFIG_HISAX_S0BOX=y
+CONFIG_HISAX_FRITZPCI=y
+CONFIG_HISAX_AVM_A1_PCMCIA=y
+CONFIG_HISAX_ELSA=y
+CONFIG_HISAX_DIEHLDIVA=y
+CONFIG_HISAX_SEDLBAUER=y
+CONFIG_HISAX_NICCY=y
+CONFIG_HISAX_GAZEL=y
+CONFIG_HISAX_HFC_SX=y
+# CONFIG_HISAX_DEBUG is not set
+
+#
+# HiSax PCMCIA card service modules
+#
+CONFIG_HISAX_SEDLBAUER_CS=m
+CONFIG_HISAX_ELSA_CS=m
+CONFIG_HISAX_AVM_A1_CS=m
+CONFIG_HISAX_TELES_CS=m
+
+#
+# HiSax sub driver modules
+#
+CONFIG_HISAX_ST5481=m
+CONFIG_HISAX_HFCUSB=m
+# CONFIG_HISAX_HFC4S8S is not set
+CONFIG_HISAX_HDLC=y
+
+#
+# Active cards
+#
+
+#
+# Siemens Gigaset
+#
+# CONFIG_ISDN_DRV_GIGASET is not set
+
+#
+# CAPI subsystem
+#
+CONFIG_ISDN_CAPI=m
+CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y
+CONFIG_ISDN_CAPI_MIDDLEWARE=y
+CONFIG_ISDN_CAPI_CAPI20=m
+CONFIG_ISDN_CAPI_CAPIFS_BOOL=y
+CONFIG_ISDN_CAPI_CAPIFS=m
+CONFIG_ISDN_CAPI_CAPIDRV=m
+
+#
+# CAPI hardware drivers
+#
+
+#
+# Active AVM cards
+#
+CONFIG_CAPI_AVM=y
+CONFIG_ISDN_DRV_AVMB1_B1PCMCIA=m
+CONFIG_ISDN_DRV_AVMB1_AVM_CS=m
+
+#
+# Active Eicon DIVA Server cards
+#
+CONFIG_CAPI_EICON=y
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=m
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+CONFIG_INPUT_JOYDEV=m
+CONFIG_INPUT_TSDEV=m
+CONFIG_INPUT_TSDEV_SCREEN_X=240
+CONFIG_INPUT_TSDEV_SCREEN_Y=320
+CONFIG_INPUT_EVDEV=m
+CONFIG_INPUT_EVBUG=m
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+CONFIG_KEYBOARD_SUNKBD=m
+CONFIG_KEYBOARD_LKKBD=m
+CONFIG_KEYBOARD_XTKBD=m
+CONFIG_KEYBOARD_NEWTON=m
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=m
+CONFIG_MOUSE_SERIAL=m
+CONFIG_MOUSE_VSXXXAA=m
+CONFIG_INPUT_JOYSTICK=y
+CONFIG_JOYSTICK_ANALOG=m
+CONFIG_JOYSTICK_A3D=m
+CONFIG_JOYSTICK_ADI=m
+CONFIG_JOYSTICK_COBRA=m
+CONFIG_JOYSTICK_GF2K=m
+CONFIG_JOYSTICK_GRIP=m
+CONFIG_JOYSTICK_GRIP_MP=m
+CONFIG_JOYSTICK_GUILLEMOT=m
+CONFIG_JOYSTICK_INTERACT=m
+CONFIG_JOYSTICK_SIDEWINDER=m
+CONFIG_JOYSTICK_TMDC=m
+CONFIG_JOYSTICK_IFORCE=m
+CONFIG_JOYSTICK_IFORCE_USB=y
+CONFIG_JOYSTICK_IFORCE_232=y
+CONFIG_JOYSTICK_WARRIOR=m
+CONFIG_JOYSTICK_MAGELLAN=m
+CONFIG_JOYSTICK_SPACEORB=m
+CONFIG_JOYSTICK_SPACEBALL=m
+CONFIG_JOYSTICK_STINGER=m
+# CONFIG_JOYSTICK_TWIDJOY is not set
+CONFIG_JOYSTICK_DB9=m
+CONFIG_JOYSTICK_GAMECON=m
+CONFIG_JOYSTICK_TURBOGRAFX=m
+CONFIG_JOYSTICK_JOYDUMP=m
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_GUNZE=m
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=m
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=m
+CONFIG_SERIO_PARKBD=m
+CONFIG_SERIO_LIBPS2=y
+CONFIG_SERIO_RAW=m
+CONFIG_GAMEPORT=m
+CONFIG_GAMEPORT_NS558=m
+CONFIG_GAMEPORT_L4=m
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+CONFIG_SERIAL_NONSTANDARD=y
+CONFIG_COMPUTONE=m
+CONFIG_ROCKETPORT=m
+CONFIG_CYCLADES=m
+# CONFIG_CYZ_INTR is not set
+CONFIG_DIGIEPCA=m
+CONFIG_MOXA_INTELLIO=m
+CONFIG_MOXA_SMARTIO=m
+# CONFIG_ISI is not set
+CONFIG_SYNCLINKMP=m
+CONFIG_N_HDLC=m
+# CONFIG_RISCOM8 is not set
+# CONFIG_SPECIALIX is not set
+CONFIG_SX=m
+CONFIG_RIO=m
+CONFIG_RIO_OLDPCI=y
+CONFIG_STALDRV=y
+CONFIG_STALLION=m
+CONFIG_ISTALLION=m
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_CS=m
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+CONFIG_SERIAL_8250_RSA=y
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+CONFIG_PRINTER=m
+# CONFIG_LP_CONSOLE is not set
+CONFIG_PPDEV=m
+CONFIG_TIPAR=m
+
+#
+# IPMI
+#
+CONFIG_IPMI_HANDLER=m
+# CONFIG_IPMI_PANIC_EVENT is not set
+CONFIG_IPMI_DEVICE_INTERFACE=m
+CONFIG_IPMI_SI=m
+CONFIG_IPMI_WATCHDOG=m
+CONFIG_IPMI_POWEROFF=m
+
+#
+# Watchdog Cards
+#
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+CONFIG_SOFT_WATCHDOG=m
+
+#
+# USB-based Watchdog Cards
+#
+CONFIG_USBPCWATCHDOG=m
+CONFIG_NVRAM=m
+CONFIG_DTLK=m
+CONFIG_R3964=m
+
+#
+# Ftape, the floppy tape device driver
+#
+
+#
+# PCMCIA character devices
+#
+CONFIG_SYNCLINK_CS=m
+# CONFIG_CARDMAN_4000 is not set
+# CONFIG_CARDMAN_4040 is not set
+CONFIG_RAW_DRIVER=m
+CONFIG_MAX_RAW_DEVS=256
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+# CONFIG_TELCLOCK is not set
+
+#
+# I2C support
+#
+CONFIG_I2C=m
+CONFIG_I2C_CHARDEV=m
+
+#
+# I2C Algorithms
+#
+CONFIG_I2C_ALGOBIT=m
+CONFIG_I2C_ALGOPCF=m
+CONFIG_I2C_ALGOPCA=m
+
+#
+# I2C Hardware Bus support
+#
+CONFIG_I2C_ISA=m
+CONFIG_I2C_PARPORT=m
+CONFIG_I2C_PARPORT_LIGHT=m
+CONFIG_I2C_STUB=m
+CONFIG_I2C_PCA_ISA=m
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
+CONFIG_SENSORS_EEPROM=m
+CONFIG_SENSORS_PCF8574=m
+# CONFIG_SENSORS_PCA9539 is not set
+CONFIG_SENSORS_PCF8591=m
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
+# Dallas's 1-wire bus
+#
+CONFIG_W1=m
+
+#
+# 1-wire Bus Masters
+#
+# CONFIG_W1_MASTER_DS9490 is not set
+# CONFIG_W1_MASTER_DS2482 is not set
+
+#
+# 1-wire Slaves
+#
+# CONFIG_W1_SLAVE_THERM is not set
+# CONFIG_W1_SLAVE_SMEM is not set
+# CONFIG_W1_SLAVE_DS2433 is not set
+
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+CONFIG_HWMON_VID=m
+CONFIG_SENSORS_ADM1021=m
+CONFIG_SENSORS_ADM1025=m
+CONFIG_SENSORS_ADM1026=m
+CONFIG_SENSORS_ADM1031=m
+# CONFIG_SENSORS_ADM9240 is not set
+CONFIG_SENSORS_ASB100=m
+# CONFIG_SENSORS_ATXP1 is not set
+CONFIG_SENSORS_DS1621=m
+# CONFIG_SENSORS_F71805F is not set
+CONFIG_SENSORS_FSCHER=m
+# CONFIG_SENSORS_FSCPOS is not set
+CONFIG_SENSORS_GL518SM=m
+# CONFIG_SENSORS_GL520SM is not set
+CONFIG_SENSORS_IT87=m
+CONFIG_SENSORS_LM63=m
+CONFIG_SENSORS_LM75=m
+CONFIG_SENSORS_LM77=m
+CONFIG_SENSORS_LM78=m
+CONFIG_SENSORS_LM80=m
+CONFIG_SENSORS_LM83=m
+CONFIG_SENSORS_LM85=m
+CONFIG_SENSORS_LM87=m
+CONFIG_SENSORS_LM90=m
+# CONFIG_SENSORS_LM92 is not set
+CONFIG_SENSORS_MAX1619=m
+CONFIG_SENSORS_PC87360=m
+CONFIG_SENSORS_SMSC47M1=m
+# CONFIG_SENSORS_SMSC47B397 is not set
+CONFIG_SENSORS_W83781D=m
+# CONFIG_SENSORS_W83792D is not set
+CONFIG_SENSORS_W83L785TS=m
+CONFIG_SENSORS_W83627HF=m
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Misc devices
+#
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+CONFIG_DVB=y
+CONFIG_DVB_CORE=m
+
+#
+# Supported USB Adapters
+#
+# CONFIG_DVB_USB is not set
+CONFIG_DVB_TTUSB_BUDGET=m
+CONFIG_DVB_TTUSB_DEC=m
+CONFIG_DVB_CINERGYT2=m
+CONFIG_DVB_CINERGYT2_TUNING=y
+CONFIG_DVB_CINERGYT2_STREAM_URB_COUNT=32
+CONFIG_DVB_CINERGYT2_STREAM_BUF_SIZE=512
+CONFIG_DVB_CINERGYT2_QUERY_INTERVAL=250
+CONFIG_DVB_CINERGYT2_ENABLE_RC_INPUT_DEVICE=y
+CONFIG_DVB_CINERGYT2_RC_QUERY_INTERVAL=100
+
+#
+# Supported FlexCopII (B2C2) Adapters
+#
+# CONFIG_DVB_B2C2_FLEXCOP is not set
+
+#
+# Supported DVB Frontends
+#
+
+#
+# Customise DVB Frontends
+#
+
+#
+# DVB-S (satellite) frontends
+#
+CONFIG_DVB_STV0299=m
+CONFIG_DVB_CX24110=m
+# CONFIG_DVB_CX24123 is not set
+CONFIG_DVB_TDA8083=m
+CONFIG_DVB_MT312=m
+CONFIG_DVB_VES1X93=m
+# CONFIG_DVB_S5H1420 is not set
+
+#
+# DVB-T (terrestrial) frontends
+#
+CONFIG_DVB_SP8870=m
+CONFIG_DVB_SP887X=m
+CONFIG_DVB_CX22700=m
+CONFIG_DVB_CX22702=m
+CONFIG_DVB_L64781=m
+CONFIG_DVB_TDA1004X=m
+CONFIG_DVB_NXT6000=m
+CONFIG_DVB_MT352=m
+# CONFIG_DVB_ZL10353 is not set
+CONFIG_DVB_DIB3000MB=m
+CONFIG_DVB_DIB3000MC=m
+
+#
+# DVB-C (cable) frontends
+#
+CONFIG_DVB_VES1820=m
+CONFIG_DVB_TDA10021=m
+CONFIG_DVB_STV0297=m
+
+#
+# ATSC (North American/Korean Terresterial DTV) frontends
+#
+# CONFIG_DVB_NXT200X is not set
+# CONFIG_DVB_OR51211 is not set
+# CONFIG_DVB_OR51132 is not set
+# CONFIG_DVB_BCM3510 is not set
+# CONFIG_DVB_LGDT330X is not set
+# CONFIG_USB_DABUSB is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+
+#
+# Sound
+#
+CONFIG_SOUND=m
+
+#
+# Advanced Linux Sound Architecture
+#
+CONFIG_SND=m
+CONFIG_SND_TIMER=m
+CONFIG_SND_PCM=m
+CONFIG_SND_HWDEP=m
+CONFIG_SND_RAWMIDI=m
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_PCM_OSS_PLUGINS=y
+CONFIG_SND_SEQUENCER_OSS=y
+# CONFIG_SND_DYNAMIC_MINORS is not set
+CONFIG_SND_SUPPORT_OLD_API=y
+CONFIG_SND_VERBOSE_PROCFS=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+
+#
+# Generic devices
+#
+CONFIG_SND_MPU401_UART=m
+CONFIG_SND_DUMMY=m
+CONFIG_SND_VIRMIDI=m
+CONFIG_SND_MTPAV=m
+CONFIG_SND_SERIAL_U16550=m
+CONFIG_SND_MPU401=m
+
+#
+# ALSA ARM devices
+#
+
+#
+# USB devices
+#
+CONFIG_SND_USB_AUDIO=m
+
+#
+# PCMCIA devices
+#
+
+#
+# Open Sound System
+#
+CONFIG_SOUND_PRIME=m
+# CONFIG_OBSOLETE_OSS_DRIVER is not set
+# CONFIG_SOUND_MSNDCLAS is not set
+# CONFIG_SOUND_MSNDPIN is not set
+CONFIG_SOUND_TVMIXER=m
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB=m
+# CONFIG_USB_DEBUG is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+CONFIG_USB_BANDWIDTH=y
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
+# CONFIG_USB_OTG is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_ISP116X_HCD is not set
+CONFIG_USB_SL811_HCD=m
+# CONFIG_USB_SL811_CS is not set
+
+#
+# USB Device Class drivers
+#
+CONFIG_USB_ACM=m
+CONFIG_USB_PRINTER=m
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+CONFIG_USB_STORAGE=m
+# CONFIG_USB_STORAGE_DEBUG is not set
+CONFIG_USB_STORAGE_DATAFAB=y
+CONFIG_USB_STORAGE_FREECOM=y
+CONFIG_USB_STORAGE_ISD200=y
+CONFIG_USB_STORAGE_DPCM=y
+CONFIG_USB_STORAGE_USBAT=y
+CONFIG_USB_STORAGE_SDDR09=y
+CONFIG_USB_STORAGE_SDDR55=y
+CONFIG_USB_STORAGE_JUMPSHOT=y
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=m
+CONFIG_USB_HIDINPUT=y
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
+# CONFIG_HID_FF is not set
+CONFIG_USB_HIDDEV=y
+
+#
+# USB HID Boot Protocol drivers
+#
+CONFIG_USB_KBD=m
+CONFIG_USB_MOUSE=m
+CONFIG_USB_AIPTEK=m
+CONFIG_USB_WACOM=m
+# CONFIG_USB_ACECAD is not set
+CONFIG_USB_KBTAB=m
+CONFIG_USB_POWERMATE=m
+CONFIG_USB_MTOUCH=m
+# CONFIG_USB_ITMTOUCH is not set
+CONFIG_USB_EGALAX=m
+# CONFIG_USB_YEALINK is not set
+CONFIG_USB_XPAD=m
+CONFIG_USB_ATI_REMOTE=m
+# CONFIG_USB_ATI_REMOTE2 is not set
+# CONFIG_USB_KEYSPAN_REMOTE is not set
+# CONFIG_USB_APPLETOUCH is not set
+
+#
+# USB Imaging devices
+#
+CONFIG_USB_MDC800=m
+CONFIG_USB_MICROTEK=m
+
+#
+# USB Network Adapters
+#
+CONFIG_USB_CATC=m
+CONFIG_USB_KAWETH=m
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
+CONFIG_USB_USBNET=m
+CONFIG_USB_NET_AX8817X=m
+CONFIG_USB_NET_CDCETHER=m
+# CONFIG_USB_NET_GL620A is not set
+CONFIG_USB_NET_NET1080=m
+# CONFIG_USB_NET_PLUSB is not set
+# CONFIG_USB_NET_RNDIS_HOST is not set
+# CONFIG_USB_NET_CDC_SUBSET is not set
+CONFIG_USB_NET_ZAURUS=m
+# CONFIG_USB_ZD1201 is not set
+CONFIG_USB_MON=y
+
+#
+# USB port drivers
+#
+CONFIG_USB_USS720=m
+
+#
+# USB Serial Converter support
+#
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+# CONFIG_USB_SERIAL_AIRPRIME is not set
+# CONFIG_USB_SERIAL_ANYDATA is not set
+CONFIG_USB_SERIAL_BELKIN=m
+CONFIG_USB_SERIAL_WHITEHEAT=m
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
+# CONFIG_USB_SERIAL_CP2101 is not set
+CONFIG_USB_SERIAL_CYPRESS_M8=m
+CONFIG_USB_SERIAL_EMPEG=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_VISOR=m
+CONFIG_USB_SERIAL_IPAQ=m
+CONFIG_USB_SERIAL_IR=m
+CONFIG_USB_SERIAL_EDGEPORT=m
+CONFIG_USB_SERIAL_EDGEPORT_TI=m
+# CONFIG_USB_SERIAL_GARMIN is not set
+CONFIG_USB_SERIAL_IPW=m
+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
+CONFIG_USB_SERIAL_KEYSPAN=m
+# CONFIG_USB_SERIAL_KEYSPAN_MPR is not set
+# CONFIG_USB_SERIAL_KEYSPAN_USA28 is not set
+# CONFIG_USB_SERIAL_KEYSPAN_USA28X is not set
+# CONFIG_USB_SERIAL_KEYSPAN_USA28XA is not set
+# CONFIG_USB_SERIAL_KEYSPAN_USA28XB is not set
+# CONFIG_USB_SERIAL_KEYSPAN_USA19 is not set
+# CONFIG_USB_SERIAL_KEYSPAN_USA18X is not set
+# CONFIG_USB_SERIAL_KEYSPAN_USA19W is not set
+# CONFIG_USB_SERIAL_KEYSPAN_USA19QW is not set
+# CONFIG_USB_SERIAL_KEYSPAN_USA19QI is not set
+# CONFIG_USB_SERIAL_KEYSPAN_USA49W is not set
+# CONFIG_USB_SERIAL_KEYSPAN_USA49WLC is not set
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_KOBIL_SCT=m
+CONFIG_USB_SERIAL_MCT_U232=m
+# CONFIG_USB_SERIAL_NAVMAN is not set
+CONFIG_USB_SERIAL_PL2303=m
+# CONFIG_USB_SERIAL_HP4X is not set
+CONFIG_USB_SERIAL_SAFE=m
+# CONFIG_USB_SERIAL_SAFE_PADDED is not set
+# CONFIG_USB_SERIAL_TI is not set
+CONFIG_USB_SERIAL_CYBERJACK=m
+CONFIG_USB_SERIAL_XIRCOM=m
+CONFIG_USB_SERIAL_OMNINET=m
+CONFIG_USB_EZUSB=y
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+CONFIG_USB_AUERSWALD=m
+CONFIG_USB_RIO500=m
+CONFIG_USB_LEGOTOWER=m
+CONFIG_USB_LCD=m
+CONFIG_USB_LED=m
+CONFIG_USB_CYTHERM=m
+CONFIG_USB_PHIDGETKIT=m
+CONFIG_USB_PHIDGETSERVO=m
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_LD is not set
+CONFIG_USB_TEST=m
+
+#
+# USB DSL modem support
+#
+CONFIG_USB_ATM=m
+CONFIG_USB_SPEEDTOUCH=m
+# CONFIG_USB_CXACRU is not set
+# CONFIG_USB_UEAGLEATM is not set
+# CONFIG_USB_XUSBATM is not set
+
+#
+# USB Gadget Support
+#
+CONFIG_USB_GADGET=m
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_PXA2XX is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+# CONFIG_USB_GADGET_OMAP is not set
+# CONFIG_USB_GADGET_AT91 is not set
+CONFIG_USB_GADGET_DUMMY_HCD=y
+CONFIG_USB_DUMMY_HCD=m
+CONFIG_USB_GADGET_DUALSPEED=y
+CONFIG_USB_ZERO=m
+CONFIG_USB_ETH=m
+CONFIG_USB_ETH_RNDIS=y
+CONFIG_USB_GADGETFS=m
+CONFIG_USB_FILE_STORAGE=m
+# CONFIG_USB_FILE_STORAGE_TEST is not set
+CONFIG_USB_G_SERIAL=m
+
+#
+# MMC/SD Card support
+#
+CONFIG_MMC=m
+# CONFIG_MMC_DEBUG is not set
+CONFIG_MMC_BLOCK=m
+
+#
+# Real Time Clock
+#
+CONFIG_RTC_LIB=y
+# CONFIG_RTC_CLASS is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=m
+CONFIG_EXT3_FS_XATTR=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_JBD=m
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+CONFIG_REISERFS_FS=m
+# CONFIG_REISERFS_CHECK is not set
+# CONFIG_REISERFS_PROC_INFO is not set
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+CONFIG_REISERFS_FS_SECURITY=y
+CONFIG_JFS_FS=m
+CONFIG_JFS_POSIX_ACL=y
+# CONFIG_JFS_SECURITY is not set
+# CONFIG_JFS_DEBUG is not set
+CONFIG_JFS_STATISTICS=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_EXPORT=y
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_SECURITY=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_XFS_RT=y
+# CONFIG_OCFS2_FS is not set
+CONFIG_MINIX_FS=m
+CONFIG_ROMFS_FS=m
+CONFIG_INOTIFY=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V1=m
+CONFIG_QFMT_V2=m
+CONFIG_QUOTACTL=y
+CONFIG_DNOTIFY=y
+CONFIG_AUTOFS_FS=m
+CONFIG_AUTOFS4_FS=m
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_ZISOFS_FS=m
+CONFIG_UDF_FS=m
+CONFIG_UDF_NLS=y
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+CONFIG_NTFS_FS=m
+# CONFIG_NTFS_DEBUG is not set
+# CONFIG_NTFS_RW is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+CONFIG_ADFS_FS=m
+# CONFIG_ADFS_FS_RW is not set
+CONFIG_AFFS_FS=m
+CONFIG_HFS_FS=m
+CONFIG_HFSPLUS_FS=m
+CONFIG_BEFS_FS=m
+# CONFIG_BEFS_DEBUG is not set
+CONFIG_BFS_FS=m
+CONFIG_EFS_FS=m
+CONFIG_JFFS_FS=m
+CONFIG_JFFS_FS_VERBOSE=0
+CONFIG_JFFS_PROC_FS=y
+CONFIG_JFFS2_FS=m
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_CRAMFS=y
+CONFIG_VXFS_FS=m
+CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_SYSV_FS=m
+CONFIG_UFS_FS=m
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
+CONFIG_NFS_DIRECTIO=y
+CONFIG_NFSD=m
+CONFIG_NFSD_V3=y
+# CONFIG_NFSD_V3_ACL is not set
+CONFIG_NFSD_V4=y
+CONFIG_NFSD_TCP=y
+CONFIG_LOCKD=m
+CONFIG_LOCKD_V4=y
+CONFIG_EXPORTFS=m
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=m
+CONFIG_SUNRPC_GSS=m
+CONFIG_RPCSEC_GSS_KRB5=m
+CONFIG_RPCSEC_GSS_SPKM3=m
+CONFIG_SMB_FS=m
+# CONFIG_SMB_NLS_DEFAULT is not set
+CONFIG_CIFS=m
+# CONFIG_CIFS_STATS is not set
+# CONFIG_CIFS_XATTR is not set
+# CONFIG_CIFS_EXPERIMENTAL is not set
+CONFIG_NCP_FS=m
+CONFIG_NCPFS_PACKET_SIGNING=y
+CONFIG_NCPFS_IOCTL_LOCKING=y
+CONFIG_NCPFS_STRONG=y
+CONFIG_NCPFS_NFS_NS=y
+CONFIG_NCPFS_OS2_NS=y
+# CONFIG_NCPFS_SMALLDOS is not set
+CONFIG_NCPFS_NLS=y
+CONFIG_NCPFS_EXTRAS=y
+CONFIG_CODA_FS=m
+# CONFIG_CODA_FS_OLD_API is not set
+CONFIG_AFS_FS=m
+CONFIG_RXRPC=m
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_ACORN_PARTITION=y
+# CONFIG_ACORN_PARTITION_CUMANA is not set
+# CONFIG_ACORN_PARTITION_EESOX is not set
+CONFIG_ACORN_PARTITION_ICS=y
+# CONFIG_ACORN_PARTITION_ADFS is not set
+# CONFIG_ACORN_PARTITION_POWERTEC is not set
+CONFIG_ACORN_PARTITION_RISCIX=y
+CONFIG_OSF_PARTITION=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_ATARI_PARTITION=y
+CONFIG_MAC_PARTITION=y
+CONFIG_MSDOS_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_LDM_PARTITION=y
+# CONFIG_LDM_DEBUG is not set
+CONFIG_SGI_PARTITION=y
+CONFIG_ULTRIX_PARTITION=y
+CONFIG_SUN_PARTITION=y
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+
+#
+# Native Language Support
+#
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="cp437"
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+
+#
+# Profiling support
+#
+CONFIG_PROFILING=y
+CONFIG_OPROFILE=m
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_DEBUG_SLAB is not set
+CONFIG_DEBUG_PREEMPT=y
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_FS is not set
+# CONFIG_DEBUG_VM is not set
+CONFIG_FRAME_POINTER=y
+# CONFIG_UNWIND_INFO is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_DEBUG_USER is not set
+# CONFIG_DEBUG_WAITQ is not set
+# CONFIG_DEBUG_ERRORS is not set
+CONFIG_DEBUG_LL=y
+# CONFIG_DEBUG_ICEDCC is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+CONFIG_SECURITY=y
+# CONFIG_SECURITY_NETWORK is not set
+CONFIG_SECURITY_CAPABILITIES=m
+CONFIG_SECURITY_ROOTPLUG=m
+CONFIG_SECURITY_SECLVL=m
+
+#
+# Cryptographic options
+#
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_NULL=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_SHA1=m
+CONFIG_CRYPTO_SHA256=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_WP512=m
+# CONFIG_CRYPTO_TGR192 is not set
+CONFIG_CRYPTO_DES=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_AES=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_ARC4=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_DEFLATE=m
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_CRC32C=m
+CONFIG_CRYPTO_TEST=m
+
+#
+# Hardware crypto devices
+#
+
+#
+# Library routines
+#
+CONFIG_CRC_CCITT=m
+CONFIG_CRC16=m
+CONFIG_CRC32=y
+CONFIG_LIBCRC32C=m
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=m
+CONFIG_REED_SOLOMON=m
+CONFIG_REED_SOLOMON_DEC16=y
diff --git a/arch/arm/kernel/entry-common.S b/arch/arm/kernel/entry-common.S
index dbcb11a..b5bcebc 100644
--- a/arch/arm/kernel/entry-common.S
+++ b/arch/arm/kernel/entry-common.S
@@ -271,7 +271,7 @@
 @ r8 = syscall table
 		.type	sys_syscall, #function
 sys_syscall:
-		eor	scno, r0, #__NR_OABI_SYSCALL_BASE
+		bic	scno, r0, #__NR_OABI_SYSCALL_BASE
 		cmp	scno, #__NR_syscall - __NR_SYSCALL_BASE
 		cmpne	scno, #NR_syscalls	@ check range
 		stmloia	sp, {r5, r6}		@ shuffle args
diff --git a/arch/arm/kernel/irq.c b/arch/arm/kernel/irq.c
index 2d5896b..bcc19fb 100644
--- a/arch/arm/kernel/irq.c
+++ b/arch/arm/kernel/irq.c
@@ -342,10 +342,10 @@
 
 #ifdef CONFIG_NO_IDLE_HZ
 	if (!(action->flags & SA_TIMER) && system_timer->dyn_tick != NULL) {
-		write_seqlock(&xtime_lock);
+		spin_lock(&system_timer->dyn_tick->lock);
 		if (system_timer->dyn_tick->state & DYN_TICK_ENABLED)
 			system_timer->dyn_tick->handler(irq, 0, regs);
-		write_sequnlock(&xtime_lock);
+		spin_unlock(&system_timer->dyn_tick->lock);
 	}
 #endif
 
diff --git a/arch/arm/kernel/time.c b/arch/arm/kernel/time.c
index d6bd435..9c12d4f 100644
--- a/arch/arm/kernel/time.c
+++ b/arch/arm/kernel/time.c
@@ -379,7 +379,7 @@
 	int ret = -ENODEV;
 
 	if (dyn_tick) {
-		write_seqlock_irqsave(&xtime_lock, flags);
+		spin_lock_irqsave(&dyn_tick->lock, flags);
 		ret = 0;
 		if (!(dyn_tick->state & DYN_TICK_ENABLED)) {
 			ret = dyn_tick->enable();
@@ -387,7 +387,7 @@
 			if (ret == 0)
 				dyn_tick->state |= DYN_TICK_ENABLED;
 		}
-		write_sequnlock_irqrestore(&xtime_lock, flags);
+		spin_unlock_irqrestore(&dyn_tick->lock, flags);
 	}
 
 	return ret;
@@ -400,7 +400,7 @@
 	int ret = -ENODEV;
 
 	if (dyn_tick) {
-		write_seqlock_irqsave(&xtime_lock, flags);
+		spin_lock_irqsave(&dyn_tick->lock, flags);
 		ret = 0;
 		if (dyn_tick->state & DYN_TICK_ENABLED) {
 			ret = dyn_tick->disable();
@@ -408,7 +408,7 @@
 			if (ret == 0)
 				dyn_tick->state &= ~DYN_TICK_ENABLED;
 		}
-		write_sequnlock_irqrestore(&xtime_lock, flags);
+		spin_unlock_irqrestore(&dyn_tick->lock, flags);
 	}
 
 	return ret;
@@ -422,15 +422,20 @@
 void timer_dyn_reprogram(void)
 {
 	struct dyn_tick_timer *dyn_tick = system_timer->dyn_tick;
-	unsigned long next, seq;
+	unsigned long next, seq, flags;
 
-	if (dyn_tick && (dyn_tick->state & DYN_TICK_ENABLED)) {
+	if (!dyn_tick)
+		return;
+
+	spin_lock_irqsave(&dyn_tick->lock, flags);
+	if (dyn_tick->state & DYN_TICK_ENABLED) {
 		next = next_timer_interrupt();
 		do {
 			seq = read_seqbegin(&xtime_lock);
-			dyn_tick->reprogram(next_timer_interrupt() - jiffies);
+			dyn_tick->reprogram(next - jiffies);
 		} while (read_seqretry(&xtime_lock, seq));
 	}
+	spin_unlock_irqrestore(&dyn_tick->lock, flags);
 }
 
 static ssize_t timer_show_dyn_tick(struct sys_device *dev, char *buf)
@@ -499,5 +504,10 @@
 	if (system_timer->offset == NULL)
 		system_timer->offset = dummy_gettimeoffset;
 	system_timer->init();
+
+#ifdef CONFIG_NO_IDLE_HZ
+	if (system_timer->dyn_tick)
+		system_timer->dyn_tick->lock = SPIN_LOCK_UNLOCKED;
+#endif
 }
 
diff --git a/arch/arm/mach-lh7a40x/Kconfig b/arch/arm/mach-lh7a40x/Kconfig
index 8a17867a..558a34f 100644
--- a/arch/arm/mach-lh7a40x/Kconfig
+++ b/arch/arm/mach-lh7a40x/Kconfig
@@ -14,6 +14,7 @@
 	bool "LPD7A400 Card Engine"
 	select ARCH_LH7A400
 #	select IDE_POLL
+	select HAS_TOUCHSCREEN_ADS7843_LH7
 	help
 	  Say Y here if you are using Logic Product Development's
 	  LPD7A400 CardEngine.  For the time being, the LPD7A400 and
@@ -23,6 +24,7 @@
 	bool "LPD7A404 Card Engine"
 	select ARCH_LH7A404
 #	select IDE_POLL
+	select HAS_TOUCHSCREEN_ADC_LH7
 	help
 	  Say Y here if you are using Logic Product Development's
 	  LPD7A404 CardEngine. For the time being, the LPD7A400 and
@@ -34,6 +36,9 @@
 config ARCH_LH7A404
 	bool
 
+config LPD7A40X_CPLD_SSP
+	bool
+
 config LH7A40X_CONTIGMEM
 	bool "Disable NUMA Support"
 	depends on ARCH_LH7A40X
diff --git a/arch/arm/mach-lh7a40x/Makefile b/arch/arm/mach-lh7a40x/Makefile
index e90512d..94b8615 100644
--- a/arch/arm/mach-lh7a40x/Makefile
+++ b/arch/arm/mach-lh7a40x/Makefile
@@ -4,11 +4,14 @@
 
 # Object file lists.
 
-obj-y			:= time.o
-obj-$(CONFIG_MACH_KEV7A400) += arch-kev7a400.o irq-lh7a400.o
-obj-$(CONFIG_MACH_LPD7A400) += arch-lpd7a40x.o irq-lh7a400.o
-obj-$(CONFIG_MACH_LPD7A404) += arch-lpd7a40x.o irq-lh7a404.o
+obj-y				:= time.o clocks.o
+obj-m				:=
+obj-n				:=
+obj-				:=
 
-obj-m			:=
-obj-n			:=
-obj-			:=
+obj-$(CONFIG_MACH_KEV7A400)	+= arch-kev7a400.o irq-lh7a400.o
+obj-$(CONFIG_MACH_LPD7A400)	+= arch-lpd7a40x.o irq-lh7a400.o
+obj-$(CONFIG_MACH_LPD7A404)	+= arch-lpd7a40x.o irq-lh7a404.o
+obj-$(CONFIG_LPD7A40X_CPLD_SSP)	+= ssp-cpld.o
+obj-$(CONFIG_FB_ARMCLCD)	+= clcd.o
+
diff --git a/arch/arm/mach-lh7a40x/arch-lpd7a40x.c b/arch/arm/mach-lh7a40x/arch-lpd7a40x.c
index 12e2327..c0e6854 100644
--- a/arch/arm/mach-lh7a40x/arch-lpd7a40x.c
+++ b/arch/arm/mach-lh7a40x/arch-lpd7a40x.c
@@ -23,6 +23,28 @@
 
 #include "common.h"
 
+#define CPLD_INT_NETHERNET	(1<<0)
+#define CPLD_INTMASK_ETHERNET	(1<<2)
+#if defined (CONFIG_MACH_LPD7A400)
+# define CPLD_INT_NTOUCH		(1<<1)
+# define CPLD_INTMASK_TOUCH	(1<<3)
+# define CPLD_INT_PEN		(1<<4)
+# define CPLD_INTMASK_PEN	(1<<4)
+# define CPLD_INT_PIRQ		(1<<4)
+#endif
+#define CPLD_INTMASK_CPLD	(1<<7)
+#define CPLD_INT_CPLD		(1<<6)
+
+#define CPLD_CONTROL_SWINT		(1<<7) /* Disable all CPLD IRQs */
+#define CPLD_CONTROL_OCMSK		(1<<6) /* Mask USB1 connect IRQ */
+#define CPLD_CONTROL_PDRV		(1<<5) /* PCC_nDRV high */
+#define CPLD_CONTROL_USB1C		(1<<4) /* USB1 connect IRQ active */
+#define CPLD_CONTROL_USB1P		(1<<3) /* USB1 power disable */
+#define CPLD_CONTROL_AWKP		(1<<2) /* Auto-wakeup disabled  */
+#define CPLD_CONTROL_LCD_ENABLE		(1<<1) /* LCD Vee enable */
+#define CPLD_CONTROL_WRLAN_NENABLE	(1<<0) /* SMC91x power disable */
+
+
 static struct resource smc91x_resources[] = {
 	[0] = {
 		.start	= CPLD00_PHYS,
@@ -48,12 +70,12 @@
 static struct resource lh7a40x_usbclient_resources[] = {
 	[0] = {
 		.start	= USB_PHYS,
-		.end	= (USB_PHYS + 0xFF),
+		.end	= (USB_PHYS + PAGE_SIZE),
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= IRQ_USBINTR,
-		.end	= IRQ_USBINTR,
+		.start	= IRQ_USB,
+		.end	= IRQ_USB,
 		.flags	= IORESOURCE_IRQ,
 	},
 };
@@ -61,7 +83,8 @@
 static u64 lh7a40x_usbclient_dma_mask = 0xffffffffUL;
 
 static struct platform_device lh7a40x_usbclient_device = {
-	.name		= "lh7a40x_udc",
+//	.name		= "lh7a40x_udc",
+	.name		= "lh7-udc",
 	.id		= 0,
 	.dev		= {
 		.dma_mask = &lh7a40x_usbclient_dma_mask,
@@ -101,7 +124,7 @@
 
 #endif
 
-static struct platform_device *lpd7a40x_devs[] __initdata = {
+static struct platform_device* lpd7a40x_devs[] __initdata = {
 	&smc91x_device,
 	&lh7a40x_usbclient_device,
 #if defined (CONFIG_ARCH_LH7A404)
@@ -113,29 +136,52 @@
 
 static void __init lpd7a40x_init (void)
 {
-	CPLD_CONTROL |=     (1<<6); /* Mask USB1 connection IRQ */
+#if defined (CONFIG_MACH_LPD7A400)
+	CPLD_CONTROL |= 0
+		| CPLD_CONTROL_SWINT /* Disable software interrupt */
+		| CPLD_CONTROL_OCMSK; /* Mask USB1 connection IRQ */
 	CPLD_CONTROL &= ~(0
-			  | (1<<1) /* Disable LCD */
-			  | (1<<0) /* Enable WLAN */
+			  | CPLD_CONTROL_LCD_ENABLE	/* Disable LCD */
+			  | CPLD_CONTROL_WRLAN_NENABLE	/* Enable SMC91x */
 		);
+#endif
+
+#if defined (CONFIG_MACH_LPD7A404)
+	CPLD_CONTROL &= ~(0
+			  | CPLD_CONTROL_WRLAN_NENABLE	/* Enable SMC91x */
+		);
+#endif
 
 	platform_add_devices (lpd7a40x_devs, ARRAY_SIZE (lpd7a40x_devs));
+#if defined (CONFIG_FB_ARMCLCD)
+        lh7a40x_clcd_init ();
+#endif
 }
 
 static void lh7a40x_ack_cpld_irq (u32 irq)
 {
-	/* CPLD doesn't have ack capability */
+	/* CPLD doesn't have ack capability, but some devices may */
+
+#if defined (CPLD_INTMASK_TOUCH)
+	/* The touch control *must* mask the the interrupt because the
+	 * interrupt bit is read by the driver to determine if the pen
+	 * is still down. */
+	if (irq == IRQ_TOUCH)
+		CPLD_INTERRUPTS |= CPLD_INTMASK_TOUCH;
+#endif
 }
 
 static void lh7a40x_mask_cpld_irq (u32 irq)
 {
 	switch (irq) {
 	case IRQ_LPD7A40X_ETH_INT:
-		CPLD_INTERRUPTS = CPLD_INTERRUPTS | 0x4;
+		CPLD_INTERRUPTS |= CPLD_INTMASK_ETHERNET;
 		break;
-	case IRQ_LPD7A400_TS:
-		CPLD_INTERRUPTS = CPLD_INTERRUPTS | 0x8;
+#if defined (IRQ_TOUCH)
+	case IRQ_TOUCH:
+		CPLD_INTERRUPTS |= CPLD_INTMASK_TOUCH;
 		break;
+#endif
 	}
 }
 
@@ -143,11 +189,13 @@
 {
 	switch (irq) {
 	case IRQ_LPD7A40X_ETH_INT:
-		CPLD_INTERRUPTS = CPLD_INTERRUPTS & ~ 0x4;
+		CPLD_INTERRUPTS &= ~CPLD_INTMASK_ETHERNET;
 		break;
-	case IRQ_LPD7A400_TS:
-		CPLD_INTERRUPTS = CPLD_INTERRUPTS & ~ 0x8;
+#if defined (IRQ_TOUCH)
+	case IRQ_TOUCH:
+		CPLD_INTERRUPTS &= ~CPLD_INTMASK_TOUCH;
 		break;
+#endif
 	}
 }
 
@@ -164,11 +212,13 @@
 
 	desc->chip->ack (irq);
 
-	if ((mask & 0x1) == 0)	/* WLAN */
+	if ((mask & (1<<0)) == 0)	/* WLAN */
 		IRQ_DISPATCH (IRQ_LPD7A40X_ETH_INT);
 
-	if ((mask & 0x2) == 0)	/* Touch */
-		IRQ_DISPATCH (IRQ_LPD7A400_TS);
+#if defined (IRQ_TOUCH)
+	if ((mask & (1<<1)) == 0)	/* Touch */
+		IRQ_DISPATCH (IRQ_TOUCH);
+#endif
 
 	desc->chip->unmask (irq); /* Level-triggered need this */
 }
@@ -204,9 +254,21 @@
 
 		/* Then, configure CPLD interrupt */
 
-	CPLD_INTERRUPTS	=   0x9c; /* Disable all CPLD interrupts */
+			/* Disable all CPLD interrupts */
+#if defined (CONFIG_MACH_LPD7A400)
+	CPLD_INTERRUPTS	= CPLD_INTMASK_TOUCH | CPLD_INTMASK_PEN
+		| CPLD_INTMASK_ETHERNET;
+	/* *** FIXME: don't know why we need 7 and 4. 7 is way wrong
+               and 4 is uncefined. */
+	// (1<<7)|(1<<4)|(1<<3)|(1<<2);
+#endif
+#if defined (CONFIG_MACH_LPD7A404)
+	CPLD_INTERRUPTS	= CPLD_INTMASK_ETHERNET;
+	/* *** FIXME: don't know why we need 6 and 5, neither is defined. */
+	// (1<<6)|(1<<5)|(1<<3);
+#endif
 	GPIO_PFDD	&= ~(1 << pinCPLD); /* Make input */
-	GPIO_INTTYPE1	|=  (1 << pinCPLD); /* Edge triggered */
+	GPIO_INTTYPE1	&= ~(1 << pinCPLD); /* Level triggered */
 	GPIO_INTTYPE2	&= ~(1 << pinCPLD); /* Active low */
 	barrier ();
 	GPIO_GPIOFINTEN |=  (1 << pinCPLD); /* Enable */
@@ -216,7 +278,7 @@
 	for (irq = IRQ_BOARD_START;
 	     irq < IRQ_BOARD_START + NR_IRQ_BOARD; ++irq) {
 		set_irq_chip (irq, &lpd7a40x_cpld_chip);
-		set_irq_handler (irq, do_edge_IRQ);
+		set_irq_handler (irq, do_level_IRQ);
 		set_irq_flags (irq, IRQF_VALID);
 	}
 
@@ -226,91 +288,109 @@
 				 lpd7a40x_cpld_handler);
 }
 
-static struct map_desc lpd7a400_io_desc[] __initdata = {
+static struct map_desc lpd7a40x_io_desc[] __initdata = {
 	{
-		.virtual	=     IO_VIRT,
+		.virtual	= IO_VIRT,
 		.pfn		= __phys_to_pfn(IO_PHYS),
-		.length		= 	    IO_SIZE,
+		.length		= IO_SIZE,
 		.type		= MT_DEVICE
-	}, {	/* Mapping added to work around chip select problems */
+	},
+	{	/* Mapping added to work around chip select problems */
 		.virtual	= IOBARRIER_VIRT,
 		.pfn		= __phys_to_pfn(IOBARRIER_PHYS),
 		.length		= IOBARRIER_SIZE,
 		.type		= MT_DEVICE
-	}, {
+	},
+	{
 		.virtual	= CF_VIRT,
 		.pfn		= __phys_to_pfn(CF_PHYS),
-		.length		= 	CF_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= CPLD02_VIRT,
-		.pfn		= __phys_to_pfn(CPLD02_PHYS),
-		.length		= 	CPLD02_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= CPLD06_VIRT,
-		.pfn		= __phys_to_pfn(CPLD06_PHYS),
-		.length		= 	CPLD06_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= CPLD08_VIRT,
-		.pfn		= __phys_to_pfn(CPLD08_PHYS),
-		.length		= 	CPLD08_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= CPLD0C_VIRT,
-		.pfn		= __phys_to_pfn(CPLD0C_PHYS),
-		.length		= 	CPLD0C_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= CPLD0E_VIRT,
-		.pfn		= __phys_to_pfn(CPLD0E_PHYS),
-		.length		= 	CPLD0E_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= CPLD10_VIRT,
-		.pfn		= __phys_to_pfn(CPLD10_PHYS),
-		.length		= 	CPLD10_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= CPLD12_VIRT,
-		.pfn		= __phys_to_pfn(CPLD12_PHYS),
-		.length		= 	CPLD12_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= CPLD14_VIRT,
-		.pfn		= __phys_to_pfn(CPLD14_PHYS),
-		.length		= 	CPLD14_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= CPLD16_VIRT,
-		.pfn		= __phys_to_pfn(CPLD16_PHYS),
-		.length		= 	CPLD16_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= CPLD18_VIRT,
-		.pfn		= __phys_to_pfn(CPLD18_PHYS),
-		.length		= 	CPLD18_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= CPLD1A_VIRT,
-		.pfn		= __phys_to_pfn(CPLD1A_PHYS),
-		.length		= 	CPLD1A_SIZE,
+		.length		= CF_SIZE,
 		.type		= MT_DEVICE
 	},
-	/* This mapping is redundant since the smc driver performs another. */
-/*	{ CPLD00_VIRT,  CPLD00_PHYS,	CPLD00_SIZE,	MT_DEVICE }, */
+	{
+		.virtual	= CPLD02_VIRT,
+		.pfn		= __phys_to_pfn(CPLD02_PHYS),
+		.length		= CPLD02_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
+		.virtual	= CPLD06_VIRT,
+		.pfn		= __phys_to_pfn(CPLD06_PHYS),
+		.length		= CPLD06_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
+		.virtual	= CPLD08_VIRT,
+		.pfn		= __phys_to_pfn(CPLD08_PHYS),
+		.length		= CPLD08_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
+		.virtual	= CPLD08_VIRT,
+		.pfn		= __phys_to_pfn(CPLD08_PHYS),
+		.length		= CPLD08_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
+		.virtual	= CPLD0A_VIRT,
+		.pfn		= __phys_to_pfn(CPLD0A_PHYS),
+		.length		= CPLD0A_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
+		.virtual	= CPLD0C_VIRT,
+		.pfn		= __phys_to_pfn(CPLD0C_PHYS),
+		.length		= CPLD0C_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
+		.virtual	= CPLD0E_VIRT,
+		.pfn		= __phys_to_pfn(CPLD0E_PHYS),
+		.length		= CPLD0E_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
+		.virtual	= CPLD10_VIRT,
+		.pfn		= __phys_to_pfn(CPLD10_PHYS),
+		.length		= CPLD10_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
+		.virtual	= CPLD12_VIRT,
+		.pfn		= __phys_to_pfn(CPLD12_PHYS),
+		.length		= CPLD12_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
+		.virtual	= CPLD14_VIRT,
+		.pfn		= __phys_to_pfn(CPLD14_PHYS),
+		.length		= CPLD14_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
+		.virtual	= CPLD16_VIRT,
+		.pfn		= __phys_to_pfn(CPLD16_PHYS),
+		.length		= CPLD16_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
+		.virtual	= CPLD18_VIRT,
+		.pfn		= __phys_to_pfn(CPLD18_PHYS),
+		.length		= CPLD18_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
+		.virtual	= CPLD1A_VIRT,
+		.pfn		= __phys_to_pfn(CPLD1A_PHYS),
+		.length		= CPLD1A_SIZE,
+		.type		= MT_DEVICE
+	},
 };
 
 void __init
-lpd7a400_map_io(void)
+lpd7a40x_map_io(void)
 {
-	iotable_init (lpd7a400_io_desc, ARRAY_SIZE (lpd7a400_io_desc));
-
-		/* Fixup (improve) Static Memory Controller settings */
-	SMC_BCR0 = 0x200039af;	/* Boot Flash */
-	SMC_BCR6 = 0x1000fbe0;	/* CPLD */
-	SMC_BCR7 = 0x1000b2c2;	/* Compact Flash */
+	iotable_init (lpd7a40x_io_desc, ARRAY_SIZE (lpd7a40x_io_desc));
 }
 
 #ifdef CONFIG_MACH_LPD7A400
@@ -320,7 +400,7 @@
 	.phys_io	= 0x80000000,
 	.io_pg_offst	= ((io_p2v (0x80000000))>>18) & 0xfffc,
 	.boot_params	= 0xc0000100,
-	.map_io		= lpd7a400_map_io,
+	.map_io		= lpd7a40x_map_io,
 	.init_irq	= lh7a400_init_irq,
 	.timer		= &lh7a40x_timer,
 	.init_machine	= lpd7a40x_init,
@@ -335,7 +415,7 @@
 	.phys_io	= 0x80000000,
 	.io_pg_offst	= ((io_p2v (0x80000000))>>18) & 0xfffc,
 	.boot_params	= 0xc0000100,
-	.map_io		= lpd7a400_map_io,
+	.map_io		= lpd7a40x_map_io,
 	.init_irq	= lh7a404_init_irq,
 	.timer		= &lh7a40x_timer,
 	.init_machine	= lpd7a40x_init,
diff --git a/arch/arm/mach-lh7a40x/clcd.c b/arch/arm/mach-lh7a40x/clcd.c
new file mode 100644
index 0000000..93751fe
--- /dev/null
+++ b/arch/arm/mach-lh7a40x/clcd.c
@@ -0,0 +1,241 @@
+/*
+ *  arch/arm/mach-lh7a40x/clcd.c
+ *
+ *  Copyright (C) 2004 Marc Singer
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License
+ *  version 2 as published by the Free Software Foundation.
+ *
+ */
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+
+//#include <linux/module.h>
+//#include <linux/time.h>
+//#include <asm/hardware.h>
+
+//#include <asm/mach/time.h>
+#include <asm/irq.h>
+#include <asm/mach/irq.h>
+
+#include <asm/system.h>
+#include <asm/hardware.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/clcd.h>
+
+#define HRTFTC_HRSETUP		__REG(HRTFTC_PHYS + 0x00)
+#define HRTFTC_HRCON		__REG(HRTFTC_PHYS + 0x04)
+#define HRTFTC_HRTIMING1	__REG(HRTFTC_PHYS + 0x08)
+#define HRTFTC_HRTIMING2	__REG(HRTFTC_PHYS + 0x0c)
+
+#define ALI_SETUP		__REG(ALI_PHYS + 0x00)
+#define ALI_CONTROL		__REG(ALI_PHYS + 0x04)
+#define ALI_TIMING1		__REG(ALI_PHYS + 0x08)
+#define ALI_TIMING2		__REG(ALI_PHYS + 0x0c)
+
+#include "lcd-panel.h"
+
+static void lh7a40x_clcd_disable (struct clcd_fb *fb)
+{
+#if defined (CONFIG_MACH_LPD7A400)
+	CPLD_CONTROL &= ~(1<<1);	/* Disable LCD Vee */
+#endif
+
+#if defined (CONFIG_MACH_LPD7A404)
+	GPIO_PCD  &= ~(1<<3);		/* Disable LCD Vee */
+#endif
+
+#if defined (CONFIG_ARCH_LH7A400)
+	HRTFTC_HRSETUP &= ~(1<<13);	/* Disable HRTFT controller */
+#endif
+
+#if defined (CONFIG_ARCH_LH7A404)
+	ALI_SETUP &= ~(1<<13);		/* Disable ALI */
+#endif
+}
+
+static void lh7a40x_clcd_enable (struct clcd_fb *fb)
+{
+	struct clcd_panel_extra* extra
+		= (struct clcd_panel_extra*) fb->board_data;
+
+#if defined (CONFIG_MACH_LPD7A400)
+	CPLD_CONTROL |= (1<<1);		/* Enable LCD Vee */
+#endif
+
+#if defined (CONFIG_MACH_LPD7A404)
+	GPIO_PCDD &= ~(1<<3);		/* Enable LCD Vee */
+	GPIO_PCD  |=  (1<<3);
+#endif
+
+#if defined (CONFIG_ARCH_LH7A400)
+
+	if (extra) {
+		HRTFTC_HRSETUP
+			= (1 << 13)
+			| ((fb->fb.var.xres - 1) << 4)
+			| 0xc
+			| (extra->hrmode ? 1 : 0);
+		HRTFTC_HRCON
+			= ((extra->clsen ? 1 : 0) << 1)
+			| ((extra->spsen ? 1 : 0) << 0);
+		HRTFTC_HRTIMING1
+			= (extra->pcdel << 8)
+			| (extra->revdel << 4)
+			| (extra->lpdel << 0);
+		HRTFTC_HRTIMING2
+			= (extra->spldel << 9)
+			| (extra->pc2del << 0);
+	}
+	else
+		HRTFTC_HRSETUP
+			= (1 << 13)
+			| 0xc;
+#endif
+
+#if defined (CONFIG_ARCH_LH7A404)
+
+	if (extra) {
+		ALI_SETUP
+			= (1 << 13)
+			| ((fb->fb.var.xres - 1) << 4)
+			| 0xc
+			| (extra->hrmode ? 1 : 0);
+		ALI_CONTROL
+			= ((extra->clsen ? 1 : 0) << 1)
+			| ((extra->spsen ? 1 : 0) << 0);
+		ALI_TIMING1
+			= (extra->pcdel << 8)
+			| (extra->revdel << 4)
+			| (extra->lpdel << 0);
+		ALI_TIMING2
+			= (extra->spldel << 9)
+			| (extra->pc2del << 0);
+	}
+	else
+		ALI_SETUP
+			= (1 << 13)
+			| 0xc;
+#endif
+
+}
+
+#define FRAMESIZE(s) (((s) + PAGE_SIZE - 1)&PAGE_MASK)
+
+static int lh7a40x_clcd_setup (struct clcd_fb *fb)
+{
+	dma_addr_t dma;
+	u32 len = FRAMESIZE (lcd_panel.mode.xres*lcd_panel.mode.yres
+			     *(lcd_panel.bpp/8));
+
+	fb->panel = &lcd_panel;
+
+		/* Enforce the sync polarity defaults */
+	if (!(fb->panel->tim2 & TIM2_IHS))
+		fb->fb.var.sync |= FB_SYNC_HOR_HIGH_ACT;
+	if (!(fb->panel->tim2 & TIM2_IVS))
+		fb->fb.var.sync |= FB_SYNC_VERT_HIGH_ACT;
+
+#if defined (HAS_LCD_PANEL_EXTRA)
+	fb->board_data = &lcd_panel_extra;
+#endif
+
+	fb->fb.screen_base
+		= dma_alloc_writecombine (&fb->dev->dev, len,
+					  &dma, GFP_KERNEL);
+	printk ("CLCD: LCD setup fb virt 0x%p phys 0x%p l %x io 0x%p \n",
+		fb->fb.screen_base, (void*) dma, len,
+		(void*) io_p2v (CLCDC_PHYS));
+	printk ("CLCD: pixclock %d\n", lcd_panel.mode.pixclock);
+
+	if (!fb->fb.screen_base) {
+		printk(KERN_ERR "CLCD: unable to map framebuffer\n");
+		return -ENOMEM;
+	}
+
+#if defined (USE_RGB555)
+	fb->fb.var.green.length = 5; /* Panel uses RGB 5:5:5 */
+#endif
+
+	fb->fb.fix.smem_start = dma;
+	fb->fb.fix.smem_len = len;
+
+		/* Drive PE4 high to prevent CPLD crash */
+	GPIO_PEDD |= (1<<4);
+	GPIO_PED  |= (1<<4);
+
+	GPIO_PINMUX |= (1<<1) | (1<<0); /* LCDVD[15:4] */
+
+//	fb->fb.fbops->fb_check_var (&fb->fb.var, &fb->fb);
+//	fb->fb.fbops->fb_set_par (&fb->fb);
+
+	return 0;
+}
+
+static int lh7a40x_clcd_mmap (struct clcd_fb *fb, struct vm_area_struct *vma)
+{
+	return dma_mmap_writecombine(&fb->dev->dev, vma,
+				     fb->fb.screen_base,
+				     fb->fb.fix.smem_start,
+				     fb->fb.fix.smem_len);
+}
+
+static void lh7a40x_clcd_remove (struct clcd_fb *fb)
+{
+	dma_free_writecombine (&fb->dev->dev, fb->fb.fix.smem_len,
+			       fb->fb.screen_base, fb->fb.fix.smem_start);
+}
+
+static struct clcd_board clcd_platform_data = {
+	.name		= "lh7a40x FB",
+	.check		= clcdfb_check,
+	.decode		= clcdfb_decode,
+	.enable		= lh7a40x_clcd_enable,
+	.setup		= lh7a40x_clcd_setup,
+	.mmap		= lh7a40x_clcd_mmap,
+	.remove		= lh7a40x_clcd_remove,
+	.disable	= lh7a40x_clcd_disable,
+};
+
+#define IRQ_CLCDC (IRQ_LCDINTR)
+
+#define AMBA_DEVICE(name,busid,base,plat,pid)			\
+static struct amba_device name##_device = {			\
+	.dev = {						\
+		.coherent_dma_mask = ~0,			\
+		.bus_id	= busid,				\
+		.platform_data = plat,				\
+		},						\
+	.res = {						\
+		.start	= base##_PHYS,				\
+		.end	= (base##_PHYS) + (4*1024) - 1,		\
+		.flags	= IORESOURCE_MEM,			\
+		},						\
+	.dma_mask	= ~0,					\
+	.irq		= { IRQ_##base, },			\
+	/* .dma		= base##_DMA,*/				\
+	.periphid = pid,					\
+}
+
+AMBA_DEVICE(clcd,  "cldc-lh7a40x",  CLCDC,     &clcd_platform_data, 0x41110);
+
+static struct amba_device *amba_devs[] __initdata = {
+	&clcd_device,
+};
+
+void __init lh7a40x_clcd_init (void)
+{
+	int i;
+	int result;
+	printk ("CLCD: registering amba devices\n");
+	for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
+		struct amba_device *d = amba_devs[i];
+		result = amba_device_register(d, &iomem_resource);
+		printk ("  %d -> %d\n", i ,result);
+	}
+}
diff --git a/arch/arm/mach-lh7a40x/clocks.c b/arch/arm/mach-lh7a40x/clocks.c
new file mode 100644
index 0000000..2291afe9
--- /dev/null
+++ b/arch/arm/mach-lh7a40x/clocks.c
@@ -0,0 +1,199 @@
+/* arch/arm/mach-lh7a40x/clocks.c
+ *
+ *  Copyright (C) 2004 Marc Singer
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License
+ *  version 2 as published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/cpufreq.h>
+#include <asm/hardware.h>
+#include <asm/arch/clocks.h>
+#include <linux/err.h>
+
+struct module;
+struct icst525_params;
+
+struct clk {
+	struct list_head node;
+	unsigned long rate;
+	struct module *owner;
+	const char *name;
+//	void *data;
+//	const struct icst525_params *params;
+//	void (*setvco)(struct clk *, struct icst525_vco vco);
+};
+
+int clk_register(struct clk *clk);
+void clk_unregister(struct clk *clk);
+
+/* ----- */
+
+#define MAINDIV1(c)	(((c) >>  7) & 0x0f)
+#define MAINDIV2(c)	(((c) >> 11) & 0x1f)
+#define PS(c)		(((c) >> 18) & 0x03)
+#define PREDIV(c)	(((c) >>  2) & 0x1f)
+#define HCLKDIV(c)	(((c) >>  0) & 0x02)
+#define PCLKDIV(c)	(((c) >> 16) & 0x03)
+
+unsigned int cpufreq_get (unsigned int cpu) /* in kHz */
+{
+	return fclkfreq_get ()/1000;
+}
+EXPORT_SYMBOL(cpufreq_get);
+
+unsigned int fclkfreq_get (void)
+{
+	unsigned int clkset = CSC_CLKSET;
+	unsigned int gclk
+		= XTAL_IN
+		/ (1 << PS(clkset))
+		* (MAINDIV1(clkset) + 2)
+		/ (PREDIV(clkset)   + 2)
+		* (MAINDIV2(clkset) + 2)
+		;
+	return gclk;
+}
+
+unsigned int hclkfreq_get (void)
+{
+	unsigned int clkset = CSC_CLKSET;
+	unsigned int hclk = fclkfreq_get () / (HCLKDIV(clkset) + 1);
+
+	return hclk;
+}
+
+unsigned int pclkfreq_get (void)
+{
+	unsigned int clkset = CSC_CLKSET;
+	int pclkdiv = PCLKDIV(clkset);
+	unsigned int pclk;
+	if (pclkdiv == 0x3)
+		pclkdiv = 0x2;
+	pclk = hclkfreq_get () / (1 << pclkdiv);
+
+	return pclk;
+}
+
+/* ----- */
+
+static LIST_HEAD(clocks);
+static DECLARE_MUTEX(clocks_sem);
+
+struct clk *clk_get (struct device *dev, const char *id)
+{
+	struct clk *p;
+	struct clk *clk = ERR_PTR(-ENOENT);
+
+	down (&clocks_sem);
+	list_for_each_entry (p, &clocks, node) {
+		if (strcmp (id, p->name) == 0
+		    && try_module_get(p->owner)) {
+			clk = p;
+			break;
+		}
+	}
+	up (&clocks_sem);
+
+	return clk;
+}
+EXPORT_SYMBOL(clk_get);
+
+void clk_put (struct clk *clk)
+{
+	module_put(clk->owner);
+}
+EXPORT_SYMBOL(clk_put);
+
+int clk_enable (struct clk *clk)
+{
+	return 0;
+}
+EXPORT_SYMBOL(clk_enable);
+
+void clk_disable (struct clk *clk)
+{
+}
+EXPORT_SYMBOL(clk_disable);
+
+int clk_use (struct clk *clk)
+{
+	return 0;
+}
+EXPORT_SYMBOL(clk_use);
+
+void clk_unuse (struct clk *clk)
+{
+}
+EXPORT_SYMBOL(clk_unuse);
+
+unsigned long clk_get_rate (struct clk *clk)
+{
+	return clk->rate;
+}
+EXPORT_SYMBOL(clk_get_rate);
+
+long clk_round_rate (struct clk *clk, unsigned long rate)
+{
+	return rate;
+}
+EXPORT_SYMBOL(clk_round_rate);
+
+int clk_set_rate (struct clk *clk, unsigned long rate)
+{
+	int ret = -EIO;
+	return ret;
+}
+EXPORT_SYMBOL(clk_set_rate);
+
+#if 0
+/*
+ * These are fixed clocks.
+ */
+static struct clk kmi_clk = {
+	.name	= "KMIREFCLK",
+	.rate	= 24000000,
+};
+
+static struct clk uart_clk = {
+	.name	= "UARTCLK",
+	.rate	= 24000000,
+};
+
+static struct clk mmci_clk = {
+	.name	= "MCLK",
+	.rate	= 33000000,
+};
+#endif
+
+static struct clk clcd_clk = {
+	.name	= "CLCDCLK",
+	.rate	= 0,
+};
+
+int clk_register (struct clk *clk)
+{
+	down (&clocks_sem);
+	list_add (&clk->node, &clocks);
+	up (&clocks_sem);
+	return 0;
+}
+EXPORT_SYMBOL(clk_register);
+
+void clk_unregister (struct clk *clk)
+{
+	down (&clocks_sem);
+	list_del (&clk->node);
+	up (&clocks_sem);
+}
+EXPORT_SYMBOL(clk_unregister);
+
+static int __init clk_init (void)
+{
+	clk_register(&clcd_clk);
+	return 0;
+}
+arch_initcall(clk_init);
diff --git a/arch/arm/mach-lh7a40x/common.h b/arch/arm/mach-lh7a40x/common.h
index ea8de7e..18e8bb4 100644
--- a/arch/arm/mach-lh7a40x/common.h
+++ b/arch/arm/mach-lh7a40x/common.h
@@ -12,6 +12,7 @@
 
 extern void lh7a400_init_irq (void);
 extern void lh7a404_init_irq (void);
+extern void lh7a40x_clcd_init (void);
 extern void lh7a40x_init_board_irq (void);
 
 #define IRQ_DISPATCH(irq) desc_handle_irq((irq),(irq_desc + irq), regs)
diff --git a/arch/arm/mach-lh7a40x/irq-lh7a404.c b/arch/arm/mach-lh7a40x/irq-lh7a404.c
index e902e3d..2685a81 100644
--- a/arch/arm/mach-lh7a40x/irq-lh7a404.c
+++ b/arch/arm/mach-lh7a40x/irq-lh7a404.c
@@ -28,13 +28,17 @@
 
 static unsigned char irq_pri_vic1[] = {
 #if defined (USE_PRIORITIES)
-IRQ_GPIO3INTR,
+	IRQ_GPIO3INTR,			/* CPLD */
+	IRQ_DMAM2P4, IRQ_DMAM2P5,	/* AC97 */
 #endif
 };
 static unsigned char irq_pri_vic2[] = {
 #if defined (USE_PRIORITIES)
-	IRQ_T3UI, IRQ_GPIO7INTR,
+	IRQ_T3UI,			/* Timer */
+	IRQ_GPIO7INTR,			/* CPLD */
 	IRQ_UART1INTR, IRQ_UART2INTR, IRQ_UART3INTR,
+	IRQ_LCDINTR,			/* LCD */
+	IRQ_TSCINTR,			/* ADC/Touchscreen */
 #endif
 };
 
@@ -98,10 +102,19 @@
 
   /* IRQ initialization */
 
+#if defined (CONFIG_ARCH_LH7A400) && defined (CONFIG_ARCH_LH7A404)
+extern void* branch_irq_lh7a400;
+#endif
+
 void __init lh7a404_init_irq (void)
 {
 	int irq;
 
+#if defined (CONFIG_ARCH_LH7A400) && defined (CONFIG_ARCH_LH7A404)
+#define NOP 0xe1a00000			/* mov r0, r0 */
+	branch_irq_lh7a400 = NOP;
+#endif
+
 	VIC1_INTENCLR = 0xffffffff;
 	VIC2_INTENCLR = 0xffffffff;
 	VIC1_INTSEL = 0;		/* All IRQs */
diff --git a/arch/arm/mach-lh7a40x/lcd-panel.h b/arch/arm/mach-lh7a40x/lcd-panel.h
new file mode 100644
index 0000000..4fb2efc
--- /dev/null
+++ b/arch/arm/mach-lh7a40x/lcd-panel.h
@@ -0,0 +1,346 @@
+/* lcd-panel.h
+     $Id$
+
+   written by Marc Singer
+   18 Jul 2005
+
+   Copyright (C) 2005 Marc Singer
+
+   -----------
+   DESCRIPTION
+   -----------
+
+   Only one panel may be defined at a time.
+
+   The pixel clock is calculated to be no greater than the target.
+
+   Each timing value is accompanied by a specification comment.
+
+     UNITS/MIN/TYP/MAX
+
+   Most of the units will be in clocks.
+
+   USE_RGB555
+
+     Define this macro to configure the AMBA LCD controller to use an
+     RGB555 encoding for the pels instead of the normal RGB565.
+
+   LPD9520, LPD79524, LPD7A400, LPD7A404-10, LPD7A404-11
+
+     These boards are best approximated by 555 for all panels.  Some
+     can use an extra low-order bit of blue in bit 16 of the color
+     value, but we don't have a way to communicate this non-linear
+     mapping to the kernel.
+
+*/
+
+#if !defined (__LCD_PANEL_H__)
+#    define   __LCD_PANEL_H__
+
+#if defined (MACH_LPD79520)\
+ || defined (MACH_LPD79524)\
+ || defined (MACH_LPD7A400)\
+ || defined (MACH_LPD7A404)
+# define USE_RGB555
+#endif
+
+struct clcd_panel_extra {
+	unsigned int hrmode;
+	unsigned int clsen;
+	unsigned int spsen;
+	unsigned int pcdel;
+	unsigned int revdel;
+	unsigned int lpdel;
+	unsigned int spldel;
+	unsigned int pc2del;
+};
+
+#define NS_TO_CLOCK(ns,c)	((((ns)*((c)/1000) + (1000000 - 1))/1000000))
+#define CLOCK_TO_DIV(e,c)	(((c) + (e) - 1)/(e))
+
+#if defined CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
+
+	/* Logic Product Development LCD 3.5" QVGA HRTFT -10 */
+	/* Sharp PN LQ035Q7DB02 w/HRTFT controller chip */
+
+#define PIX_CLOCK_TARGET	(6800000)
+#define PIX_CLOCK_DIVIDER	CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK		(HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+	.mode	= {
+		.name		= "3.5in QVGA (LQ035Q7DB02)",
+		.xres		= 240,
+		.yres		= 320,
+		.pixclock	= PIX_CLOCK,
+		.left_margin	= 16,
+		.right_margin	= 21,
+		.upper_margin	= 8,			// line/8/8/8
+		.lower_margin	= 5,
+		.hsync_len	= 61,
+		.vsync_len	= NS_TO_CLOCK (60, PIX_CLOCK),
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+	.width		= -1,
+	.height		= -1,
+	.tim2		= TIM2_IPC | (PIX_CLOCK_DIVIDER - 2),
+	.cntl		= CNTL_LCDTFT | CNTL_WATERMARK,
+	.bpp		= 16,
+};
+
+#define HAS_LCD_PANEL_EXTRA
+
+static struct clcd_panel_extra lcd_panel_extra = {
+	.hrmode = 1,
+	.clsen = 1,
+	.spsen = 1,
+	.pcdel = 8,
+	.revdel = 7,
+	.lpdel = 13,
+	.spldel = 77,
+	.pc2del = 208,
+};
+
+#endif
+
+#if defined CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02
+
+	/* Logic Product Development LCD 5.7" QVGA -10 */
+	/* Sharp PN LQ057Q3DC02 */
+	/* QVGA mode, V/Q=LOW */
+
+/* From Sharp on 2006.1.3.  I believe some of the values are incorrect
+ * based on the datasheet.
+
+    Timing0	TIMING1		TIMING2		CONTROL
+    0x140A0C4C	0x080504EF	0x013F380D	0x00000829
+    HBP= 20	VBP=  8		BCD=  0
+    HFP= 10	VFP=  5		CPL=319
+    HSW= 12	VSW=  1		IOE=  0
+    PPL= 19	LPP=239		IPC=  1
+				IHS=  1
+				IVS=  1
+				ACB=  0
+				CSEL= 0
+				PCD= 13
+
+ */
+
+/* The full horozontal cycle (Th) is clock/360/400/450. */
+/* The full vertical   cycle (Tv) is line/251/262/280. */
+
+#define PIX_CLOCK_TARGET	(6300000) /* -/6.3/7 MHz */
+#define PIX_CLOCK_DIVIDER	CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK		(HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+	.mode	= {
+		.name		= "5.7in QVGA (LQ057Q3DC02)",
+		.xres		= 320,
+		.yres		= 240,
+		.pixclock	= PIX_CLOCK,
+		.left_margin	= 11,
+		.right_margin	= 400-11-320-2,
+		.upper_margin	= 7,			// line/7/7/7
+		.lower_margin	= 262-7-240-2,
+		.hsync_len	= 2,			// clk/2/96/200
+		.vsync_len	= 2,			// line/2/-/34
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+	.width		= -1,
+	.height		= -1,
+	.tim2		= TIM2_IHS | TIM2_IVS
+			| (PIX_CLOCK_DIVIDER - 2),
+	.cntl		= CNTL_LCDTFT | CNTL_WATERMARK,
+	.bpp		= 16,
+};
+
+#endif
+
+#if defined CONFIG_FB_ARMCLCD_SHARP_LQ64D343
+
+	/* Logic Product Development LCD 6.4" VGA -10 */
+	/* Sharp PN LQ64D343 */
+
+/* The full horozontal cycle (Th) is clock/750/800/900. */
+/* The full vertical   cycle (Tv) is line/515/525/560. */
+
+#define PIX_CLOCK_TARGET	(28330000)
+#define PIX_CLOCK_DIVIDER	CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK		(HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+	.mode	= {
+		.name		= "6.4in QVGA (LQ64D343)",
+		.xres		= 640,
+		.yres		= 480,
+		.pixclock	= PIX_CLOCK,
+		.left_margin	= 32,
+		.right_margin	= 800-32-640-96,
+		.upper_margin	= 32,			// line/34/34/34
+		.lower_margin	= 540-32-480-2,
+		.hsync_len	= 96,			// clk/2/96/200
+		.vsync_len	= 2,			// line/2/-/34
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+	.width		= -1,
+	.height		= -1,
+	.tim2		= TIM2_IHS | TIM2_IVS
+			| (PIX_CLOCK_DIVIDER - 2),
+	.cntl		= CNTL_LCDTFT | CNTL_WATERMARK,
+	.bpp		= 16,
+};
+
+#endif
+
+#if defined CONFIG_FB_ARMCLCD_SHARP_LQ10D368
+
+	/* Logic Product Development LCD 10.4" VGA -10 */
+	/* Sharp PN LQ10D368 */
+
+#define PIX_CLOCK_TARGET	(28330000)
+#define PIX_CLOCK_DIVIDER	CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK		(HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+	.mode	= {
+		.name		= "10.4in VGA (LQ10D368)",
+		.xres		= 640,
+		.yres		= 480,
+		.pixclock	= PIX_CLOCK,
+		.left_margin	= 21,
+		.right_margin	= 15,
+		.upper_margin	= 34,
+		.lower_margin	= 5,
+		.hsync_len	= 96,
+		.vsync_len	= 16,
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+	.width		= -1,
+	.height		= -1,
+	.tim2		= TIM2_IHS | TIM2_IVS
+			| (PIX_CLOCK_DIVIDER - 2),
+	.cntl		= CNTL_LCDTFT | CNTL_WATERMARK,
+	.bpp		= 16,
+};
+
+#endif
+
+#if defined CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41
+
+	/* Logic Product Development LCD 12.1" SVGA -10 */
+	/* Sharp PN LQ121S1DG41, was LQ121S1DG31 */
+
+/* Note that with a 99993900 Hz HCLK, it is not possible to hit the
+ * target clock frequency range of 35MHz to 42MHz. */
+
+/* If the target pixel clock is substantially lower than the panel
+ * spec, this is done to prevent the LCD display from glitching when
+ * the CPU is under load.  A pixel clock higher than 25MHz
+ * (empirically determined) will compete with the CPU for bus cycles
+ * for the Ethernet chip.  However, even a pixel clock of 10MHz
+ * competes with Compact Flash interface during some operations
+ * (fdisk, e2fsck).  And, at that speed the display may have a visible
+ * flicker. */
+
+/* The full horozontal cycle (Th) is clock/832/1056/1395. */
+
+#define PIX_CLOCK_TARGET	(20000000)
+#define PIX_CLOCK_DIVIDER	CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK		(HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+	.mode	= {
+		.name		= "12.1in SVGA (LQ121S1DG41)",
+		.xres		= 800,
+		.yres		= 600,
+		.pixclock	= PIX_CLOCK,
+		.left_margin	= 89,		// ns/5/-/(1/PIX_CLOCK)-10
+		.right_margin	= 1056-800-89-128,
+		.upper_margin	= 23,		// line/23/23/23
+		.lower_margin	= 44,
+		.hsync_len	= 128,		// clk/2/128/200
+		.vsync_len	= 4,		// line/2/4/6
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+	.width		= -1,
+	.height		= -1,
+	.tim2		= TIM2_IHS | TIM2_IVS
+			| (PIX_CLOCK_DIVIDER - 2),
+	.cntl		= CNTL_LCDTFT | CNTL_WATERMARK,
+	.bpp		= 16,
+};
+
+#endif
+
+#if defined CONFIG_FB_ARMCLCD_HITACHI
+
+	/* Hitachi*/
+	/* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
+
+#define PIX_CLOCK_TARGET	(49000000)
+#define PIX_CLOCK_DIVIDER	CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK		(HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+	.mode	= {
+		.name		= "Hitachi 800x480",
+		.xres		= 800,
+		.yres		= 480,
+		.pixclock	= PIX_CLOCK,
+		.left_margin	= 88,
+		.right_margin	= 40,
+		.upper_margin	= 32,
+		.lower_margin	= 11,
+		.hsync_len	= 128,
+		.vsync_len	= 2,
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+	.width		= -1,
+	.height		= -1,
+	.tim2		= TIM2_IPC | TIM2_IHS | TIM2_IVS
+			| (PIX_CLOCK_DIVIDER - 2),
+	.cntl		= CNTL_LCDTFT | CNTL_WATERMARK,
+	.bpp		= 16,
+};
+
+#endif
+
+
+#if defined CONFIG_FB_ARMCLCD_AUO_A070VW01_WIDE
+
+	/* AU Optotronics  A070VW01 7.0 Wide Screen color Display*/
+	/* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
+
+#define PIX_CLOCK_TARGET	(10000000)
+#define PIX_CLOCK_DIVIDER	CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK		(HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+	.mode	= {
+		.name		= "7.0in Wide (A070VW01)",
+		.xres		= 480,
+		.yres		= 234,
+		.pixclock	= PIX_CLOCK,
+		.left_margin	= 30,
+		.right_margin	= 25,
+		.upper_margin	= 14,
+		.lower_margin	= 12,
+		.hsync_len	= 100,
+		.vsync_len	= 1,
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+	.width		= -1,
+	.height		= -1,
+	.tim2		= TIM2_IPC | TIM2_IHS | TIM2_IVS
+			| (PIX_CLOCK_DIVIDER - 2),
+	.cntl		= CNTL_LCDTFT | CNTL_WATERMARK,
+	.bpp		= 16,
+};
+
+#endif
+
+#undef NS_TO_CLOCK
+#undef CLOCK_TO_DIV
+
+#endif  /* __LCD_PANEL_H__ */
diff --git a/arch/arm/mach-lh7a40x/ssp-cpld.c b/arch/arm/mach-lh7a40x/ssp-cpld.c
new file mode 100644
index 0000000..a108301
--- /dev/null
+++ b/arch/arm/mach-lh7a40x/ssp-cpld.c
@@ -0,0 +1,343 @@
+/* arch/arm/mach-lh7a40x/ssp-cpld.c
+ *
+ *  Copyright (C) 2004,2005 Marc Singer
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License
+ *  version 2 as published by the Free Software Foundation.
+ *
+ * SSP/SPI driver for the CardEngine CPLD.
+ *
+ */
+
+/* NOTES
+   -----
+
+   o *** This driver is cribbed from the 7952x implementation.
+	 Some comments may not apply.
+
+   o This driver contains sufficient logic to control either the
+     serial EEPROMs or the audio codec.  It is included in the kernel
+     to support the codec.  The EEPROMs are really the responsibility
+     of the boot loader and should probably be left alone.
+
+   o The code must be augmented to cope with multiple, simultaneous
+     clients.
+     o The audio codec writes to the codec chip whenever playback
+       starts.
+     o The touchscreen driver writes to the ads chip every time it
+       samples.
+     o The audio codec must write 16 bits, but the touch chip writes
+       are 8 bits long.
+     o We need to be able to keep these configurations separate while
+       simultaneously active.
+
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+//#include <linux/sched.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+//#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/hardware.h>
+
+#include <asm/arch/ssp.h>
+
+//#define TALK
+
+#if defined (TALK)
+#define PRINTK(f...)		printk (f)
+#else
+#define PRINTK(f...)		do {} while (0)
+#endif
+
+#if defined (CONFIG_ARCH_LH7A400)
+# define CPLD_SPID		__REGP16(CPLD06_VIRT) /* SPI data */
+# define CPLD_SPIC		__REGP16(CPLD08_VIRT) /* SPI control */
+# define CPLD_SPIC_CS_CODEC	(1<<0)
+# define CPLD_SPIC_CS_TOUCH	(1<<1)
+# define CPLD_SPIC_WRITE	(0<<2)
+# define CPLD_SPIC_READ		(1<<2)
+# define CPLD_SPIC_DONE		(1<<3) /* r/o */
+# define CPLD_SPIC_LOAD		(1<<4)
+# define CPLD_SPIC_START	(1<<4)
+# define CPLD_SPIC_LOADED	(1<<5) /* r/o */
+#endif
+
+#define CPLD_SPI		__REGP16(CPLD0A_VIRT) /* SPI operation */
+#define CPLD_SPI_CS_EEPROM	(1<<3)
+#define CPLD_SPI_SCLK		(1<<2)
+#define CPLD_SPI_TX_SHIFT	(1)
+#define CPLD_SPI_TX		(1<<CPLD_SPI_TX_SHIFT)
+#define CPLD_SPI_RX_SHIFT	(0)
+#define CPLD_SPI_RX		(1<<CPLD_SPI_RX_SHIFT)
+
+/* *** FIXME: these timing values are substantially larger than the
+   *** chip requires. We may implement an nsleep () function. */
+#define T_SKH	1		/* Clock time high (us) */
+#define T_SKL	1		/* Clock time low (us) */
+#define T_CS	1		/* Minimum chip select low time (us)  */
+#define T_CSS	1		/* Minimum chip select setup time (us)  */
+#define T_DIS	1		/* Data setup time (us) */
+
+	 /* EEPROM SPI bits */
+#define P_START		(1<<9)
+#define P_WRITE		(1<<7)
+#define P_READ		(2<<7)
+#define P_ERASE		(3<<7)
+#define P_EWDS		(0<<7)
+#define P_WRAL		(0<<7)
+#define P_ERAL		(0<<7)
+#define P_EWEN		(0<<7)
+#define P_A_EWDS	(0<<5)
+#define P_A_WRAL	(1<<5)
+#define P_A_ERAL	(2<<5)
+#define P_A_EWEN	(3<<5)
+
+struct ssp_configuration {
+	int device;
+	int mode;
+	int speed;
+	int frame_size_write;
+	int frame_size_read;
+};
+
+static struct ssp_configuration ssp_configuration;
+static spinlock_t ssp_lock;
+
+static void enable_cs (void)
+{
+	switch (ssp_configuration.device) {
+	case DEVICE_EEPROM:
+		CPLD_SPI |= CPLD_SPI_CS_EEPROM;
+		break;
+	}
+	udelay (T_CSS);
+}
+
+static void disable_cs (void)
+{
+	switch (ssp_configuration.device) {
+	case DEVICE_EEPROM:
+		CPLD_SPI &= ~CPLD_SPI_CS_EEPROM;
+		break;
+	}
+	udelay (T_CS);
+}
+
+static void pulse_clock (void)
+{
+	CPLD_SPI |=  CPLD_SPI_SCLK;
+	udelay (T_SKH);
+	CPLD_SPI &= ~CPLD_SPI_SCLK;
+	udelay (T_SKL);
+}
+
+
+/* execute_spi_command
+
+   sends an spi command to a device.  It first sends cwrite bits from
+   v.  If cread is greater than zero it will read cread bits
+   (discarding the leading 0 bit) and return them.  If cread is less
+   than zero it will check for completetion status and return 0 on
+   success or -1 on timeout.  If cread is zero it does nothing other
+   than sending the command.
+
+   On the LPD7A400, we can only read or write multiples of 8 bits on
+   the codec and the touch screen device.  Here, we round up.
+
+*/
+
+static int execute_spi_command (int v, int cwrite, int cread)
+{
+	unsigned long l = 0;
+
+#if defined (CONFIG_MACH_LPD7A400)
+	/* The codec and touch devices cannot be bit-banged.  Instead,
+	 * the CPLD provides an eight-bit shift register and a crude
+	 * interface.  */
+	if (   ssp_configuration.device == DEVICE_CODEC
+	    || ssp_configuration.device == DEVICE_TOUCH) {
+		int select = 0;
+
+		PRINTK ("spi(%d %d.%d) 0x%04x",
+			ssp_configuration.device, cwrite, cread,
+			v);
+#if defined (TALK)
+		if (ssp_configuration.device == DEVICE_CODEC)
+			PRINTK (" 0x%03x -> %2d", v & 0x1ff, (v >> 9) & 0x7f);
+#endif
+		PRINTK ("\n");
+
+		if (ssp_configuration.device == DEVICE_CODEC)
+			select = CPLD_SPIC_CS_CODEC;
+		if (ssp_configuration.device == DEVICE_TOUCH)
+			select = CPLD_SPIC_CS_TOUCH;
+		if (cwrite) {
+			for (cwrite = (cwrite + 7)/8; cwrite-- > 0; ) {
+				CPLD_SPID = (v >> (8*cwrite)) & 0xff;
+				CPLD_SPIC = select | CPLD_SPIC_LOAD;
+				while (!(CPLD_SPIC & CPLD_SPIC_LOADED))
+					;
+				CPLD_SPIC = select;
+				while (!(CPLD_SPIC & CPLD_SPIC_DONE))
+					;
+			}
+			v = 0;
+		}
+		if (cread) {
+			mdelay (2);	/* *** FIXME: required by ads7843? */
+			v = 0;
+			for (cread = (cread + 7)/8; cread-- > 0;) {
+				CPLD_SPID = 0;
+				CPLD_SPIC = select | CPLD_SPIC_READ
+					| CPLD_SPIC_START;
+				while (!(CPLD_SPIC & CPLD_SPIC_LOADED))
+					;
+				CPLD_SPIC = select | CPLD_SPIC_READ;
+				while (!(CPLD_SPIC & CPLD_SPIC_DONE))
+					;
+				v = (v << 8) | CPLD_SPID;
+			}
+		}
+		return v;
+	}
+#endif
+
+	PRINTK ("spi(%d) 0x%04x -> 0x%x\r\n", ssp_configuration.device,
+		v & 0x1ff, (v >> 9) & 0x7f);
+
+	enable_cs ();
+
+	v <<= CPLD_SPI_TX_SHIFT; /* Correction for position of SPI_TX bit */
+	while (cwrite--) {
+		CPLD_SPI
+			= (CPLD_SPI & ~CPLD_SPI_TX)
+			| ((v >> cwrite) & CPLD_SPI_TX);
+		udelay (T_DIS);
+		pulse_clock ();
+	}
+
+	if (cread < 0) {
+		int delay = 10;
+		disable_cs ();
+		udelay (1);
+		enable_cs ();
+
+		l = -1;
+		do {
+			if (CPLD_SPI & CPLD_SPI_RX) {
+				l = 0;
+				break;
+			}
+		} while (udelay (1), --delay);
+	}
+	else
+	/* We pulse the clock before the data to skip the leading zero. */
+		while (cread-- > 0) {
+			pulse_clock ();
+			l = (l<<1)
+				| (((CPLD_SPI & CPLD_SPI_RX)
+				    >> CPLD_SPI_RX_SHIFT) & 0x1);
+		}
+
+	disable_cs ();
+	return l;
+}
+
+static int ssp_init (void)
+{
+	spin_lock_init (&ssp_lock);
+	memset (&ssp_configuration, 0, sizeof (ssp_configuration));
+	return 0;
+}
+
+
+/* ssp_chip_select
+
+   drops the chip select line for the CPLD shift-register controlled
+   devices.  It doesn't enable chip
+
+*/
+
+static void ssp_chip_select (int enable)
+{
+#if defined (CONFIG_MACH_LPD7A400)
+	int select;
+
+	if (ssp_configuration.device == DEVICE_CODEC)
+		select = CPLD_SPIC_CS_CODEC;
+	else if (ssp_configuration.device == DEVICE_TOUCH)
+		select = CPLD_SPIC_CS_TOUCH;
+	else
+		return;
+
+	if (enable)
+		CPLD_SPIC = select;
+	else
+		CPLD_SPIC = 0;
+#endif
+}
+
+static void ssp_acquire (void)
+{
+	spin_lock (&ssp_lock);
+}
+
+static void ssp_release (void)
+{
+	ssp_chip_select (0);	/* just in case */
+	spin_unlock (&ssp_lock);
+}
+
+static int ssp_configure (int device, int mode, int speed,
+			   int frame_size_write, int frame_size_read)
+{
+	ssp_configuration.device		= device;
+	ssp_configuration.mode			= mode;
+	ssp_configuration.speed			= speed;
+	ssp_configuration.frame_size_write	= frame_size_write;
+	ssp_configuration.frame_size_read	= frame_size_read;
+
+	return 0;
+}
+
+static int ssp_read (void)
+{
+	return execute_spi_command (0, 0, ssp_configuration.frame_size_read);
+}
+
+static int ssp_write (u16 data)
+{
+	execute_spi_command (data, ssp_configuration.frame_size_write, 0);
+	return 0;
+}
+
+static int ssp_write_read (u16 data)
+{
+	return execute_spi_command (data, ssp_configuration.frame_size_write,
+				    ssp_configuration.frame_size_read);
+}
+
+struct ssp_driver lh7a40x_cpld_ssp_driver = {
+	.init		= ssp_init,
+	.acquire	= ssp_acquire,
+	.release	= ssp_release,
+	.configure	= ssp_configure,
+	.chip_select	= ssp_chip_select,
+	.read		= ssp_read,
+	.write		= ssp_write,
+	.write_read	= ssp_write_read,
+};
+
+
+MODULE_AUTHOR("Marc Singer");
+MODULE_DESCRIPTION("LPD7A40X CPLD SPI driver");
+MODULE_LICENSE("GPL");
diff --git a/arch/arm/mach-lh7a40x/time.c b/arch/arm/mach-lh7a40x/time.c
index be377e3..ef9af37 100644
--- a/arch/arm/mach-lh7a40x/time.c
+++ b/arch/arm/mach-lh7a40x/time.c
@@ -1,4 +1,4 @@
-/* 
+/*
  *  arch/arm/mach-lh7a40x/time.c
  *
  *  Copyright (C) 2004 Logic Product Development
@@ -57,7 +57,7 @@
 	.handler	= lh7a40x_timer_interrupt,
 };
 
-static void __init lh7a40x_timer_init(void)
+static void __init lh7a40x_timer_init (void)
 {
 				/* Stop/disable all timers */
 	TIMER_CONTROL1 = 0;
diff --git a/arch/arm/mach-pnx4008/Makefile b/arch/arm/mach-pnx4008/Makefile
new file mode 100644
index 0000000..b457ca0
--- /dev/null
+++ b/arch/arm/mach-pnx4008/Makefile
@@ -0,0 +1,12 @@
+#
+# Makefile for the linux kernel.
+#
+
+obj-y			:= core.o irq.o time.o clock.o gpio.o serial.o dma.o
+obj-m			:=
+obj-n			:=
+obj-			:=
+
+# Power Management
+obj-$(CONFIG_PM) += pm.o sleep.o
+
diff --git a/arch/arm/mach-pnx4008/Makefile.boot b/arch/arm/mach-pnx4008/Makefile.boot
new file mode 100644
index 0000000..44c7117
--- /dev/null
+++ b/arch/arm/mach-pnx4008/Makefile.boot
@@ -0,0 +1,4 @@
+   zreladdr-y		:= 0x80008000
+params_phys-y		:= 0x80000100
+initrd_phys-y		:= 0x80800000
+
diff --git a/arch/arm/mach-pnx4008/clock.c b/arch/arm/mach-pnx4008/clock.c
new file mode 100644
index 0000000..285b22f
--- /dev/null
+++ b/arch/arm/mach-pnx4008/clock.c
@@ -0,0 +1,1010 @@
+/*
+ * arch/arm/mach-pnx4008/clock.c
+ *
+ * Clock control driver for PNX4008
+ *
+ * Authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
+ * Generic clock management functions are partially based on:
+ *  linux/arch/arm/mach-omap/clock.c
+ *
+ * 2005-2006 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/errno.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/delay.h>
+
+#include <asm/semaphore.h>
+#include <asm/hardware.h>
+#include <asm/io.h>
+
+#include <asm/arch/clock.h>
+#include "clock.h"
+
+/*forward declaration*/
+static struct clk per_ck;
+static struct clk hclk_ck;
+static struct clk ck_1MHz;
+static struct clk ck_13MHz;
+static struct clk ck_pll1;
+static int local_set_rate(struct clk *clk, u32 rate);
+
+static inline void clock_lock(void)
+{
+	local_irq_disable();
+}
+
+static inline void clock_unlock(void)
+{
+	local_irq_enable();
+}
+
+static void propagate_rate(struct clk *clk)
+{
+	struct clk *tmp_clk;
+
+	tmp_clk = clk;
+	while (tmp_clk->propagate_next) {
+		tmp_clk = tmp_clk->propagate_next;
+		local_set_rate(tmp_clk, tmp_clk->user_rate);
+	}
+}
+
+static inline void clk_reg_disable(struct clk *clk)
+{
+	if (clk->enable_reg)
+		__raw_writel(__raw_readl(clk->enable_reg) &
+			     ~(1 << clk->enable_shift), clk->enable_reg);
+}
+
+static inline void clk_reg_enable(struct clk *clk)
+{
+	if (clk->enable_reg)
+		__raw_writel(__raw_readl(clk->enable_reg) |
+			     (1 << clk->enable_shift), clk->enable_reg);
+}
+
+static inline void clk_reg_disable1(struct clk *clk)
+{
+	if (clk->enable_reg1)
+		__raw_writel(__raw_readl(clk->enable_reg1) &
+			     ~(1 << clk->enable_shift1), clk->enable_reg1);
+}
+
+static inline void clk_reg_enable1(struct clk *clk)
+{
+	if (clk->enable_reg1)
+		__raw_writel(__raw_readl(clk->enable_reg1) |
+			     (1 << clk->enable_shift1), clk->enable_reg1);
+}
+
+static int clk_wait_for_pll_lock(struct clk *clk)
+{
+	int i;
+	i = 0;
+	while (i++ < 0xFFF && !(__raw_readl(clk->scale_reg) & 1)) ;	/*wait for PLL to lock */
+
+	if (!(__raw_readl(clk->scale_reg) & 1)) {
+		printk(KERN_ERR
+		       "%s ERROR: failed to lock, scale reg data: %x\n",
+		       clk->name, __raw_readl(clk->scale_reg));
+		return -1;
+	}
+	return 0;
+}
+
+static int switch_to_dirty_13mhz(struct clk *clk)
+{
+	int i;
+	int ret;
+	u32 tmp_reg;
+
+	ret = 0;
+
+	if (!clk->rate)
+		clk_reg_enable1(clk);
+
+	tmp_reg = __raw_readl(clk->parent_switch_reg);
+	/*if 13Mhz clock selected, select 13'MHz (dirty) source from OSC */
+	if (!(tmp_reg & 1)) {
+		tmp_reg |= (1 << 1);	/* Trigger switch to 13'MHz (dirty) clock */
+		__raw_writel(tmp_reg, clk->parent_switch_reg);
+		i = 0;
+		while (i++ < 0xFFF && !(__raw_readl(clk->parent_switch_reg) & 1)) ;	/*wait for 13'MHz selection status */
+
+		if (!(__raw_readl(clk->parent_switch_reg) & 1)) {
+			printk(KERN_ERR
+			       "%s ERROR: failed to select 13'MHz, parent sw reg data: %x\n",
+			       clk->name, __raw_readl(clk->parent_switch_reg));
+			ret = -1;
+		}
+	}
+
+	if (!clk->rate)
+		clk_reg_disable1(clk);
+
+	return ret;
+}
+
+static int switch_to_clean_13mhz(struct clk *clk)
+{
+	int i;
+	int ret;
+	u32 tmp_reg;
+
+	ret = 0;
+
+	if (!clk->rate)
+		clk_reg_enable1(clk);
+
+	tmp_reg = __raw_readl(clk->parent_switch_reg);
+	/*if 13'Mhz clock selected, select 13MHz (clean) source from OSC */
+	if (tmp_reg & 1) {
+		tmp_reg &= ~(1 << 1);	/* Trigger switch to 13MHz (clean) clock */
+		__raw_writel(tmp_reg, clk->parent_switch_reg);
+		i = 0;
+		while (i++ < 0xFFF && (__raw_readl(clk->parent_switch_reg) & 1)) ;	/*wait for 13MHz selection status */
+
+		if (__raw_readl(clk->parent_switch_reg) & 1) {
+			printk(KERN_ERR
+			       "%s ERROR: failed to select 13MHz, parent sw reg data: %x\n",
+			       clk->name, __raw_readl(clk->parent_switch_reg));
+			ret = -1;
+		}
+	}
+
+	if (!clk->rate)
+		clk_reg_disable1(clk);
+
+	return ret;
+}
+
+static int set_13MHz_parent(struct clk *clk, struct clk *parent)
+{
+	int ret = -EINVAL;
+
+	if (parent == &ck_13MHz)
+		ret = switch_to_clean_13mhz(clk);
+	else if (parent == &ck_pll1)
+		ret = switch_to_dirty_13mhz(clk);
+
+	return ret;
+}
+
+#define PLL160_MIN_FCCO 156000
+#define PLL160_MAX_FCCO 320000
+
+/*
+ * Calculate pll160 settings.
+ * Possible input: up to 320MHz with step of clk->parent->rate.
+ * In PNX4008 parent rate for pll160s may be either 1 or 13MHz.
+ * Ignored paths: "feedback" (bit 13 set), "div-by-N".
+ * Setting ARM PLL4 rate to 0 will put CPU into direct run mode.
+ * Setting PLL5 and PLL3 rate to 0 will disable USB and DSP clock input.
+ * Please refer to PNX4008 IC manual for details.
+ */
+
+static int pll160_set_rate(struct clk *clk, u32 rate)
+{
+	u32 tmp_reg, tmp_m, tmp_2p, i;
+	u32 parent_rate;
+	int ret = -EINVAL;
+
+	parent_rate = clk->parent->rate;
+
+	if (!parent_rate)
+		goto out;
+
+	/* set direct run for ARM or disable output for others  */
+	clk_reg_disable(clk);
+
+	/* disable source input as well (ignored for ARM) */
+	clk_reg_disable1(clk);
+
+	tmp_reg = __raw_readl(clk->scale_reg);
+	tmp_reg &= ~0x1ffff;	/*clear all settings, power down */
+	__raw_writel(tmp_reg, clk->scale_reg);
+
+	rate -= rate % parent_rate;	/*round down the input */
+
+	if (rate > PLL160_MAX_FCCO)
+		rate = PLL160_MAX_FCCO;
+
+	if (!rate) {
+		clk->rate = 0;
+		ret = 0;
+		goto out;
+	}
+
+	clk_reg_enable1(clk);
+	tmp_reg = __raw_readl(clk->scale_reg);
+
+	if (rate == parent_rate) {
+		/*enter direct bypass mode */
+		tmp_reg |= ((1 << 14) | (1 << 15));
+		__raw_writel(tmp_reg, clk->scale_reg);
+		clk->rate = parent_rate;
+		clk_reg_enable(clk);
+		ret = 0;
+		goto out;
+	}
+
+	i = 0;
+	for (tmp_2p = 1; tmp_2p < 16; tmp_2p <<= 1) {
+		if (rate * tmp_2p >= PLL160_MIN_FCCO)
+			break;
+		i++;
+	}
+
+	if (tmp_2p > 1)
+		tmp_reg |= ((i - 1) << 11);
+	else
+		tmp_reg |= (1 << 14);	/*direct mode, no divide */
+
+	tmp_m = rate * tmp_2p;
+	tmp_m /= parent_rate;
+
+	tmp_reg |= (tmp_m - 1) << 1;	/*calculate M */
+	tmp_reg |= (1 << 16);	/*power up PLL */
+	__raw_writel(tmp_reg, clk->scale_reg);
+
+	if (clk_wait_for_pll_lock(clk) < 0) {
+		clk_reg_disable(clk);
+		clk_reg_disable1(clk);
+
+		tmp_reg = __raw_readl(clk->scale_reg);
+		tmp_reg &= ~0x1ffff;	/*clear all settings, power down */
+		__raw_writel(tmp_reg, clk->scale_reg);
+		clk->rate = 0;
+		ret = -EFAULT;
+		goto out;
+	}
+
+	clk->rate = (tmp_m * parent_rate) / tmp_2p;
+
+	if (clk->flags & RATE_PROPAGATES)
+		propagate_rate(clk);
+
+	clk_reg_enable(clk);
+	ret = 0;
+
+out:
+	return ret;
+}
+
+/*configure PER_CLK*/
+static int per_clk_set_rate(struct clk *clk, u32 rate)
+{
+	u32 tmp;
+
+	tmp = __raw_readl(clk->scale_reg);
+	tmp &= ~(0x1f << 2);
+	tmp |= ((clk->parent->rate / clk->rate) - 1) << 2;
+	__raw_writel(tmp, clk->scale_reg);
+	clk->rate = rate;
+	return 0;
+}
+
+/*configure HCLK*/
+static int hclk_set_rate(struct clk *clk, u32 rate)
+{
+	u32 tmp;
+	tmp = __raw_readl(clk->scale_reg);
+	tmp = tmp & ~0x3;
+	switch (rate) {
+	case 1:
+		break;
+	case 2:
+		tmp |= 1;
+		break;
+	case 4:
+		tmp |= 2;
+		break;
+	}
+
+	__raw_writel(tmp, clk->scale_reg);
+	clk->rate = rate;
+	return 0;
+}
+
+static u32 hclk_round_rate(struct clk *clk, u32 rate)
+{
+	switch (rate) {
+	case 1:
+	case 4:
+		return rate;
+	}
+	return 2;
+}
+
+static u32 per_clk_round_rate(struct clk *clk, u32 rate)
+{
+	return CLK_RATE_13MHZ;
+}
+
+static int on_off_set_rate(struct clk *clk, u32 rate)
+{
+	if (rate) {
+		clk_reg_enable(clk);
+		clk->rate = 1;
+	} else {
+		clk_reg_disable(clk);
+		clk->rate = 0;
+	}
+	return 0;
+}
+
+static int on_off_inv_set_rate(struct clk *clk, u32 rate)
+{
+	if (rate) {
+		clk_reg_disable(clk);	/*enable bit is inverted */
+		clk->rate = 1;
+	} else {
+		clk_reg_enable(clk);
+		clk->rate = 0;
+	}
+	return 0;
+}
+
+static u32 on_off_round_rate(struct clk *clk, u32 rate)
+{
+	return (rate ? 1 : 0);
+}
+
+static u32 pll4_round_rate(struct clk *clk, u32 rate)
+{
+	if (rate > CLK_RATE_208MHZ)
+		rate = CLK_RATE_208MHZ;
+	if (rate == CLK_RATE_208MHZ && hclk_ck.user_rate == 1)
+		rate = CLK_RATE_208MHZ - CLK_RATE_13MHZ;
+	return (rate - (rate % (hclk_ck.user_rate * CLK_RATE_13MHZ)));
+}
+
+static u32 pll3_round_rate(struct clk *clk, u32 rate)
+{
+	if (rate > CLK_RATE_208MHZ)
+		rate = CLK_RATE_208MHZ;
+	return (rate - rate % CLK_RATE_13MHZ);
+}
+
+static u32 pll5_round_rate(struct clk *clk, u32 rate)
+{
+	return (rate ? CLK_RATE_48MHZ : 0);
+}
+
+static u32 ck_13MHz_round_rate(struct clk *clk, u32 rate)
+{
+	return (rate ? CLK_RATE_13MHZ : 0);
+}
+
+static int ck_13MHz_set_rate(struct clk *clk, u32 rate)
+{
+	if (rate) {
+		clk_reg_disable(clk);	/*enable bit is inverted */
+		udelay(500);
+		clk->rate = CLK_RATE_13MHZ;
+		ck_1MHz.rate = CLK_RATE_1MHZ;
+	} else {
+		clk_reg_enable(clk);
+		clk->rate = 0;
+		ck_1MHz.rate = 0;
+	}
+	return 0;
+}
+
+static int pll1_set_rate(struct clk *clk, u32 rate)
+{
+#if 0 /* doesn't work on some boards, probably a HW BUG */
+	if (rate) {
+		clk_reg_disable(clk);	/*enable bit is inverted */
+		if (!clk_wait_for_pll_lock(clk)) {
+			clk->rate = CLK_RATE_13MHZ;
+		} else {
+			clk_reg_enable(clk);
+			clk->rate = 0;
+		}
+
+	} else {
+		clk_reg_enable(clk);
+		clk->rate = 0;
+	}
+#endif
+	return 0;
+}
+
+/* Clock sources */
+
+static struct clk osc_13MHz = {
+	.name = "osc_13MHz",
+	.flags = FIXED_RATE,
+	.rate = CLK_RATE_13MHZ,
+};
+
+static struct clk ck_13MHz = {
+	.name = "ck_13MHz",
+	.parent = &osc_13MHz,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &ck_13MHz_round_rate,
+	.set_rate = &ck_13MHz_set_rate,
+	.enable_reg = OSC13CTRL_REG,
+	.enable_shift = 0,
+	.rate = CLK_RATE_13MHZ,
+};
+
+static struct clk osc_32KHz = {
+	.name = "osc_32KHz",
+	.flags = FIXED_RATE,
+	.rate = CLK_RATE_32KHZ,
+};
+
+/*attached to PLL5*/
+static struct clk ck_1MHz = {
+	.name = "ck_1MHz",
+	.flags = FIXED_RATE | PARENT_SET_RATE,
+	.parent = &ck_13MHz,
+};
+
+/* PLL1 (397) - provides 13' MHz clock */
+static struct clk ck_pll1 = {
+	.name = "ck_pll1",
+	.parent = &osc_32KHz,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &ck_13MHz_round_rate,
+	.set_rate = &pll1_set_rate,
+	.enable_reg = PLLCTRL_REG,
+	.enable_shift = 1,
+	.scale_reg = PLLCTRL_REG,
+	.rate = CLK_RATE_13MHZ,
+};
+
+/* CPU/Bus PLL */
+static struct clk ck_pll4 = {
+	.name = "ck_pll4",
+	.parent = &ck_pll1,
+	.flags = RATE_PROPAGATES | NEEDS_INITIALIZATION,
+	.propagate_next = &per_ck,
+	.round_rate = &pll4_round_rate,
+	.set_rate = &pll160_set_rate,
+	.rate = CLK_RATE_208MHZ,
+	.scale_reg = HCLKPLLCTRL_REG,
+	.enable_reg = PWRCTRL_REG,
+	.enable_shift = 2,
+	.parent_switch_reg = SYSCLKCTRL_REG,
+	.set_parent = &set_13MHz_parent,
+};
+
+/* USB PLL */
+static struct clk ck_pll5 = {
+	.name = "ck_pll5",
+	.parent = &ck_1MHz,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &pll5_round_rate,
+	.set_rate = &pll160_set_rate,
+	.scale_reg = USBCTRL_REG,
+	.enable_reg = USBCTRL_REG,
+	.enable_shift = 18,
+	.enable_reg1 = USBCTRL_REG,
+	.enable_shift1 = 17,
+};
+
+/* XPERTTeak DSP PLL */
+static struct clk ck_pll3 = {
+	.name = "ck_pll3",
+	.parent = &ck_pll1,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &pll3_round_rate,
+	.set_rate = &pll160_set_rate,
+	.scale_reg = DSPPLLCTRL_REG,
+	.enable_reg = DSPCLKCTRL_REG,
+	.enable_shift = 3,
+	.enable_reg1 = DSPCLKCTRL_REG,
+	.enable_shift1 = 2,
+	.parent_switch_reg = DSPCLKCTRL_REG,
+	.set_parent = &set_13MHz_parent,
+};
+
+static struct clk hclk_ck = {
+	.name = "hclk_ck",
+	.parent = &ck_pll4,
+	.flags = PARENT_SET_RATE,
+	.set_rate = &hclk_set_rate,
+	.round_rate = &hclk_round_rate,
+	.scale_reg = HCLKDIVCTRL_REG,
+	.rate = 2,
+	.user_rate = 2,
+};
+
+static struct clk per_ck = {
+	.name = "per_ck",
+	.parent = &ck_pll4,
+	.flags = FIXED_RATE,
+	.propagate_next = &hclk_ck,
+	.set_rate = &per_clk_set_rate,
+	.round_rate = &per_clk_round_rate,
+	.scale_reg = HCLKDIVCTRL_REG,
+	.rate = CLK_RATE_13MHZ,
+	.user_rate = CLK_RATE_13MHZ,
+};
+
+static struct clk m2hclk_ck = {
+	.name = "m2hclk_ck",
+	.parent = &hclk_ck,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_inv_set_rate,
+	.rate = 1,
+	.enable_shift = 6,
+	.enable_reg = PWRCTRL_REG,
+};
+
+static struct clk vfp9_ck = {
+	.name = "vfp9_ck",
+	.parent = &ck_pll4,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.rate = 1,
+	.enable_shift = 4,
+	.enable_reg = VFP9CLKCTRL_REG,
+};
+
+static struct clk keyscan_ck = {
+	.name = "keyscan_ck",
+	.parent = &osc_32KHz,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 0,
+	.enable_reg = KEYCLKCTRL_REG,
+};
+
+static struct clk touch_ck = {
+	.name = "touch_ck",
+	.parent = &osc_32KHz,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 0,
+	.enable_reg = TSCLKCTRL_REG,
+};
+
+static struct clk pwm1_ck = {
+	.name = "pwm1_ck",
+	.parent = &osc_32KHz,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 0,
+	.enable_reg = PWMCLKCTRL_REG,
+};
+
+static struct clk pwm2_ck = {
+	.name = "pwm2_ck",
+	.parent = &osc_32KHz,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 2,
+	.enable_reg = PWMCLKCTRL_REG,
+};
+
+static struct clk jpeg_ck = {
+	.name = "jpeg_ck",
+	.parent = &hclk_ck,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 0,
+	.enable_reg = JPEGCLKCTRL_REG,
+};
+
+static struct clk ms_ck = {
+	.name = "ms_ck",
+	.parent = &ck_pll4,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 5,
+	.enable_reg = MSCTRL_REG,
+};
+
+static struct clk dum_ck = {
+	.name = "dum_ck",
+	.parent = &hclk_ck,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 0,
+	.enable_reg = DUMCLKCTRL_REG,
+};
+
+static struct clk flash_ck = {
+	.name = "flash_ck",
+	.parent = &hclk_ck,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 1,	/* Only MLC clock supported */
+	.enable_reg = FLASHCLKCTRL_REG,
+};
+
+static struct clk i2c0_ck = {
+	.name = "i2c0_ck",
+	.parent = &per_ck,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 0,
+	.enable_reg = I2CCLKCTRL_REG,
+};
+
+static struct clk i2c1_ck = {
+	.name = "i2c1_ck",
+	.parent = &per_ck,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 1,
+	.enable_reg = I2CCLKCTRL_REG,
+};
+
+static struct clk i2c2_ck = {
+	.name = "i2c2_ck",
+	.parent = &per_ck,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 2,
+	.enable_reg = USB_OTG_CLKCTRL_REG,
+};
+
+static struct clk spi0_ck = {
+	.name = "spi0_ck",
+	.parent = &hclk_ck,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 0,
+	.enable_reg = SPICTRL_REG,
+};
+
+static struct clk spi1_ck = {
+	.name = "spi1_ck",
+	.parent = &hclk_ck,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 4,
+	.enable_reg = SPICTRL_REG,
+};
+
+static struct clk dma_ck = {
+	.name = "dma_ck",
+	.parent = &hclk_ck,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 0,
+	.enable_reg = DMACLKCTRL_REG,
+};
+
+static struct clk uart3_ck = {
+	.name = "uart3_ck",
+	.parent = &per_ck,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.rate = 1,
+	.enable_shift = 0,
+	.enable_reg = UARTCLKCTRL_REG,
+};
+
+static struct clk uart4_ck = {
+	.name = "uart4_ck",
+	.parent = &per_ck,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 1,
+	.enable_reg = UARTCLKCTRL_REG,
+};
+
+static struct clk uart5_ck = {
+	.name = "uart5_ck",
+	.parent = &per_ck,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.rate = 1,
+	.enable_shift = 2,
+	.enable_reg = UARTCLKCTRL_REG,
+};
+
+static struct clk uart6_ck = {
+	.name = "uart6_ck",
+	.parent = &per_ck,
+	.flags = NEEDS_INITIALIZATION,
+	.round_rate = &on_off_round_rate,
+	.set_rate = &on_off_set_rate,
+	.enable_shift = 3,
+	.enable_reg = UARTCLKCTRL_REG,
+};
+
+/* These clocks are visible outside this module
+ * and can be initialized
+ */
+static struct clk *onchip_clks[] = {
+	&ck_13MHz,
+	&ck_pll1,
+	&ck_pll4,
+	&ck_pll5,
+	&ck_pll3,
+	&vfp9_ck,
+	&m2hclk_ck,
+	&hclk_ck,
+	&dma_ck,
+	&flash_ck,
+	&dum_ck,
+	&keyscan_ck,
+	&pwm1_ck,
+	&pwm2_ck,
+	&jpeg_ck,
+	&ms_ck,
+	&touch_ck,
+	&i2c0_ck,
+	&i2c1_ck,
+	&i2c2_ck,
+	&spi0_ck,
+	&spi1_ck,
+	&uart3_ck,
+	&uart4_ck,
+	&uart5_ck,
+	&uart6_ck,
+};
+
+static int local_set_rate(struct clk *clk, u32 rate)
+{
+	int ret = -EINVAL;
+	if (clk->set_rate) {
+
+		if (clk->user_rate == clk->rate && clk->parent->rate) {
+			/* if clock enabled or rate not set */
+			clk->user_rate = clk->round_rate(clk, rate);
+			ret = clk->set_rate(clk, clk->user_rate);
+		} else
+			clk->user_rate = clk->round_rate(clk, rate);
+		ret = 0;
+	}
+	return ret;
+}
+
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	int ret = -EINVAL;
+
+	if (clk->flags & FIXED_RATE)
+		goto out;
+
+	clock_lock();
+	if ((clk->flags & PARENT_SET_RATE) && clk->parent) {
+
+		clk->user_rate = clk->round_rate(clk, rate);
+		/* parent clock needs to be refreshed
+		   for the setting to take effect */
+	} else {
+		ret = local_set_rate(clk, rate);
+	}
+	ret = 0;
+	clock_unlock();
+
+out:
+	return ret;
+}
+
+EXPORT_SYMBOL(clk_set_rate);
+
+struct clk *clk_get(struct device *dev, const char *id)
+{
+	struct clk *clk = ERR_PTR(-ENOENT);
+	struct clk **clkp;
+
+	clock_lock();
+	for (clkp = onchip_clks; clkp < onchip_clks + ARRAY_SIZE(onchip_clks);
+	     clkp++) {
+		if (strcmp(id, (*clkp)->name) == 0
+		    && try_module_get((*clkp)->owner)) {
+			clk = (*clkp);
+			break;
+		}
+	}
+	clock_unlock();
+
+	return clk;
+}
+EXPORT_SYMBOL(clk_get);
+
+void clk_put(struct clk *clk)
+{
+	clock_lock();
+	if (clk && !IS_ERR(clk))
+		module_put(clk->owner);
+	clock_unlock();
+}
+EXPORT_SYMBOL(clk_put);
+
+unsigned long clk_get_rate(struct clk *clk)
+{
+	unsigned long ret;
+	clock_lock();
+	ret = clk->rate;
+	clock_unlock();
+	return ret;
+}
+EXPORT_SYMBOL(clk_get_rate);
+
+static int local_clk_enable(struct clk *clk)
+{
+	int ret = 0;
+
+	if (!(clk->flags & FIXED_RATE) && !clk->rate && clk->set_rate
+	    && clk->user_rate)
+		ret = clk->set_rate(clk, clk->user_rate);
+	return ret;
+}
+
+static void local_clk_disable(struct clk *clk)
+{
+	if (!(clk->flags & FIXED_RATE) && clk->rate && clk->set_rate)
+		clk->set_rate(clk, 0);
+}
+
+int clk_enable(struct clk *clk)
+{
+	int ret = 0;
+
+	clock_lock();
+	ret = local_clk_enable(clk);
+	clock_unlock();
+	return ret;
+}
+
+EXPORT_SYMBOL(clk_enable);
+
+void clk_disable(struct clk *clk)
+{
+	clock_lock();
+	local_clk_disable(clk);
+	clock_unlock();
+}
+
+EXPORT_SYMBOL(clk_disable);
+
+static void local_clk_unuse(struct clk *clk)
+{
+	if (clk->usecount > 0 && !(--clk->usecount)) {
+		local_clk_disable(clk);
+		if (clk->parent)
+			local_clk_unuse(clk->parent);
+	}
+}
+
+static int local_clk_use(struct clk *clk)
+{
+	int ret = 0;
+	if (clk->usecount++ == 0) {
+		if (clk->parent)
+			ret = local_clk_use(clk->parent);
+
+		if (ret != 0) {
+			clk->usecount--;
+			goto out;
+		}
+
+		ret = local_clk_enable(clk);
+
+		if (ret != 0 && clk->parent) {
+			local_clk_unuse(clk->parent);
+			clk->usecount--;
+		}
+	}
+out:
+	return ret;
+}
+
+/* The main purpose of clk_use ans clk_unuse functions
+ * is to control switching 13MHz oscillator and PLL1 (13'MHz),
+ * so that they are disabled whenever none of PLL2-5 is using them.
+ * Although in theory these functions should work with any clock,
+ * please use them only on PLL2 - PLL5 to avoid confusion.
+ */
+int clk_use(struct clk *clk)
+{
+	int ret = 0;
+
+	clock_lock();
+	ret = local_clk_use(clk);
+	clock_unlock();
+	return ret;
+}
+EXPORT_SYMBOL(clk_use);
+
+void clk_unuse(struct clk *clk)
+{
+
+	clock_lock();
+	local_clk_unuse(clk);
+	clock_unlock();
+}
+
+EXPORT_SYMBOL(clk_unuse);
+
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+	long ret;
+	clock_lock();
+	if (clk->round_rate)
+		ret = clk->round_rate(clk, rate);
+	else
+		ret = clk->rate;
+	clock_unlock();
+	return ret;
+}
+
+EXPORT_SYMBOL(clk_round_rate);
+
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	int ret = -ENODEV;
+	if (!clk->set_parent)
+		goto out;
+
+	clock_lock();
+	ret = clk->set_parent(clk, parent);
+	if (!ret)
+		clk->parent = parent;
+	clock_unlock();
+
+out:
+	return ret;
+}
+
+EXPORT_SYMBOL(clk_set_parent);
+
+static int __init clk_init(void)
+{
+	struct clk **clkp;
+
+	/* Disable autoclocking, as it doesn't seem to work */
+	__raw_writel(0xff, AUTOCLK_CTRL);
+
+	for (clkp = onchip_clks; clkp < onchip_clks + ARRAY_SIZE(onchip_clks);
+	     clkp++) {
+		if (((*clkp)->flags & NEEDS_INITIALIZATION)
+		    && ((*clkp)->set_rate)) {
+			(*clkp)->user_rate = (*clkp)->rate;
+			local_set_rate((*clkp), (*clkp)->user_rate);
+			if ((*clkp)->set_parent)
+				(*clkp)->set_parent((*clkp), (*clkp)->parent);
+		}
+		pr_debug("%s: clock %s, rate %ld\n",
+			__FUNCTION__, (*clkp)->name, (*clkp)->rate);
+	}
+
+	clk_use(&ck_pll4);
+
+	/* if ck_13MHz is not used, disable it. */
+	if (ck_13MHz.usecount == 0)
+		local_clk_disable(&ck_13MHz);
+
+	/* Disable autoclocking */
+	__raw_writeb(0xff, AUTOCLK_CTRL);
+
+	return 0;
+}
+
+arch_initcall(clk_init);
diff --git a/arch/arm/mach-pnx4008/clock.h b/arch/arm/mach-pnx4008/clock.h
new file mode 100644
index 0000000..cd58f37
--- /dev/null
+++ b/arch/arm/mach-pnx4008/clock.h
@@ -0,0 +1,43 @@
+/*
+ * arch/arm/mach-pnx4008/clock.h
+ *
+ * Clock control driver for PNX4008 - internal header file
+ *
+ * Author: Vitaly Wool <source@mvista.com>
+ *
+ * 2006 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#ifndef __ARCH_ARM_PNX4008_CLOCK_H__
+#define __ARCH_ARM_PNX4008_CLOCK_H__
+
+struct clk {
+	struct list_head node;
+	struct module *owner;
+	const char *name;
+	struct clk *parent;
+	struct clk *propagate_next;
+	u32 rate;
+	u32 user_rate;
+	s8 usecount;
+	u32 flags;
+	u32 scale_reg;
+	u8 enable_shift;
+	u32 enable_reg;
+	u8 enable_shift1;
+	u32 enable_reg1;
+	u32 parent_switch_reg;
+	 u32(*round_rate) (struct clk *, u32);
+	int (*set_rate) (struct clk *, u32);
+	int (*set_parent) (struct clk * clk, struct clk * parent);
+};
+
+/* Flags */
+#define RATE_PROPAGATES      (1<<0)
+#define NEEDS_INITIALIZATION (1<<1)
+#define PARENT_SET_RATE      (1<<2)
+#define FIXED_RATE           (1<<3)
+
+#endif
diff --git a/arch/arm/mach-pnx4008/core.c b/arch/arm/mach-pnx4008/core.c
new file mode 100644
index 0000000..ba91daa
--- /dev/null
+++ b/arch/arm/mach-pnx4008/core.c
@@ -0,0 +1,207 @@
+/*
+ * arch/arm/mach-pnx4008/core.c
+ *
+ * PNX4008 core startup code
+ *
+ * Authors: Vitaly Wool, Dmitry Chigirev,
+ * Grigory Tolstolytkin, Dmitry Pervushin <source@mvista.com>
+ *
+ * Based on reference code received from Philips:
+ * Copyright (C) 2003 Philips Semiconductors
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/mm.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/serial_8250.h>
+#include <linux/device.h>
+#include <linux/spi/spi.h>
+
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/pgtable.h>
+#include <asm/page.h>
+#include <asm/system.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/map.h>
+#include <asm/mach/time.h>
+
+#include <asm/arch/irq.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/dma.h>
+
+struct resource spipnx_0_resources[] = {
+	{
+		.start = PNX4008_SPI1_BASE,
+		.end = PNX4008_SPI1_BASE + SZ_4K,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = PER_SPI1_REC_XMIT,
+		.flags = IORESOURCE_DMA,
+	}, {
+		.start = SPI1_INT,
+		.flags = IORESOURCE_IRQ,
+	}, {
+		.flags = 0,
+	},
+};
+
+struct resource spipnx_1_resources[] = {
+	{
+		.start = PNX4008_SPI2_BASE,
+		.end = PNX4008_SPI2_BASE + SZ_4K,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = PER_SPI2_REC_XMIT,
+		.flags = IORESOURCE_DMA,
+	}, {
+		.start = SPI2_INT,
+		.flags = IORESOURCE_IRQ,
+	}, {
+		.flags = 0,
+	}
+};
+
+static struct spi_board_info spi_board_info[] __initdata = {
+	{
+		.modalias	= "m25p80",
+		.max_speed_hz	= 1000000,
+		.bus_num	= 1,
+		.chip_select	= 0,
+	},
+};
+
+static struct platform_device spipnx_1 = {
+	.name = "spipnx",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(spipnx_0_resources),
+	.resource = spipnx_0_resources,
+	.dev = {
+		.coherent_dma_mask = 0xFFFFFFFF,
+		},
+};
+
+static struct platform_device spipnx_2 = {
+	.name = "spipnx",
+	.id = 2,
+	.num_resources = ARRAY_SIZE(spipnx_1_resources),
+	.resource = spipnx_1_resources,
+	.dev = {
+		.coherent_dma_mask = 0xFFFFFFFF,
+		},
+};
+
+static struct plat_serial8250_port platform_serial_ports[] = {
+	{
+		.membase = (void *)__iomem(IO_ADDRESS(PNX4008_UART5_BASE)),
+		.mapbase = (unsigned long)PNX4008_UART5_BASE,
+		.irq = IIR5_INT,
+		.uartclk = PNX4008_UART_CLK,
+		.regshift = 2,
+		.iotype = UPIO_MEM,
+		.flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART | UPF_SKIP_TEST,
+	},
+	{
+		.membase = (void *)__iomem(IO_ADDRESS(PNX4008_UART3_BASE)),
+		.mapbase = (unsigned long)PNX4008_UART3_BASE,
+		.irq = IIR3_INT,
+		.uartclk = PNX4008_UART_CLK,
+		.regshift = 2,
+		.iotype = UPIO_MEM,
+		.flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART | UPF_SKIP_TEST,
+	 },
+	{}
+};
+
+static struct platform_device serial_device = {
+	.name = "serial8250",
+	.id = PLAT8250_DEV_PLATFORM,
+	.dev = {
+		.platform_data = &platform_serial_ports,
+	},
+};
+
+static struct platform_device *devices[] __initdata = {
+	&spipnx_1,
+	&spipnx_2,
+	&serial_device,
+};
+
+
+extern void pnx4008_uart_init(void);
+
+static void __init pnx4008_init(void)
+{
+	/*disable all START interrupt sources,
+	   and clear all START interrupt flags */
+	__raw_writel(0, START_INT_ER_REG(SE_PIN_BASE_INT));
+	__raw_writel(0, START_INT_ER_REG(SE_INT_BASE_INT));
+	__raw_writel(0xffffffff, START_INT_RSR_REG(SE_PIN_BASE_INT));
+	__raw_writel(0xffffffff, START_INT_RSR_REG(SE_INT_BASE_INT));
+
+	platform_add_devices(devices, ARRAY_SIZE(devices));
+	spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
+	/* Switch on the UART clocks */
+	pnx4008_uart_init();
+}
+
+static struct map_desc pnx4008_io_desc[] __initdata = {
+	{
+		.virtual 	= IO_ADDRESS(PNX4008_IRAM_BASE),
+		.pfn 		= __phys_to_pfn(PNX4008_IRAM_BASE),
+		.length		= SZ_64K,
+		.type 		= MT_DEVICE,
+	}, {
+		.virtual 	= IO_ADDRESS(PNX4008_NDF_FLASH_BASE),
+		.pfn 		= __phys_to_pfn(PNX4008_NDF_FLASH_BASE),
+		.length		= SZ_1M - SZ_128K,
+		.type 		= MT_DEVICE,
+	}, {
+		.virtual 	= IO_ADDRESS(PNX4008_JPEG_CONFIG_BASE),
+		.pfn 		= __phys_to_pfn(PNX4008_JPEG_CONFIG_BASE),
+		.length		= SZ_128K * 3,
+		.type 		= MT_DEVICE,
+	}, {
+		.virtual 	= IO_ADDRESS(PNX4008_DMA_CONFIG_BASE),
+		.pfn 		= __phys_to_pfn(PNX4008_DMA_CONFIG_BASE),
+		.length		= SZ_1M,
+		.type 		= MT_DEVICE,
+	}, {
+		.virtual 	= IO_ADDRESS(PNX4008_AHB2FAB_BASE),
+		.pfn 		= __phys_to_pfn(PNX4008_AHB2FAB_BASE),
+		.length		= SZ_1M,
+		.type 		= MT_DEVICE,
+	},
+};
+
+void __init pnx4008_map_io(void)
+{
+	iotable_init(pnx4008_io_desc, ARRAY_SIZE(pnx4008_io_desc));
+}
+
+extern struct sys_timer pnx4008_timer;
+
+MACHINE_START(PNX4008, "Philips PNX4008")
+	/* Maintainer: MontaVista Software Inc. */
+	.phys_io 		= 0x40090000,
+	.io_pg_offst 		= (0xf4090000 >> 18) & 0xfffc,
+	.boot_params		= 0x80000100,
+	.map_io 		= pnx4008_map_io,
+	.init_irq 		= pnx4008_init_irq,
+	.init_machine 		= pnx4008_init,
+	.timer 			= &pnx4008_timer,
+MACHINE_END
diff --git a/arch/arm/mach-pnx4008/dma.c b/arch/arm/mach-pnx4008/dma.c
new file mode 100644
index 0000000..981aa9d
--- /dev/null
+++ b/arch/arm/mach-pnx4008/dma.c
@@ -0,0 +1,1109 @@
+/*
+ *  linux/arch/arm/mach-pnx4008/dma.c
+ *
+ *  PNX4008 DMA registration and IRQ dispatching
+ *
+ *  Author:	Vitaly Wool
+ *  Copyright:	MontaVista Software Inc. (c) 2005
+ *
+ *  Based on the code from Nicolas Pitre
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/dma-mapping.h>
+#include <linux/clk.h>
+
+#include <asm/system.h>
+#include <asm/irq.h>
+#include <asm/hardware.h>
+#include <asm/dma.h>
+#include <asm/dma-mapping.h>
+#include <asm/io.h>
+#include <asm/mach/dma.h>
+#include <asm/arch/clock.h>
+
+static struct dma_channel {
+	char *name;
+	void (*irq_handler) (int, int, void *, struct pt_regs *);
+	void *data;
+	struct pnx4008_dma_ll *ll;
+	u32 ll_dma;
+	void *target_addr;
+	int target_id;
+} dma_channels[MAX_DMA_CHANNELS];
+
+static struct ll_pool {
+	void *vaddr;
+	void *cur;
+	dma_addr_t dma_addr;
+	int count;
+} ll_pool;
+
+static spinlock_t ll_lock = SPIN_LOCK_UNLOCKED;
+
+struct pnx4008_dma_ll *pnx4008_alloc_ll_entry(dma_addr_t * ll_dma)
+{
+	struct pnx4008_dma_ll *ll = NULL;
+	unsigned long flags;
+
+	spin_lock_irqsave(&ll_lock, flags);
+	if (ll_pool.count > 4) { /* can give one more */
+		ll = *(struct pnx4008_dma_ll **) ll_pool.cur;
+		*ll_dma = ll_pool.dma_addr + ((void *)ll - ll_pool.vaddr);
+		*(void **)ll_pool.cur = **(void ***)ll_pool.cur;
+		memset(ll, 0, sizeof(*ll));
+		ll_pool.count--;
+	}
+	spin_unlock_irqrestore(&ll_lock, flags);
+
+	return ll;
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_alloc_ll_entry);
+
+void pnx4008_free_ll_entry(struct pnx4008_dma_ll * ll, dma_addr_t ll_dma)
+{
+	unsigned long flags;
+
+	if (ll) {
+		if ((unsigned long)((long)ll - (long)ll_pool.vaddr) > 0x4000) {
+			printk(KERN_ERR "Trying to free entry not allocated by DMA\n");
+			BUG();
+		}
+
+		if (ll->flags & DMA_BUFFER_ALLOCATED)
+			ll->free(ll->alloc_data);
+
+		spin_lock_irqsave(&ll_lock, flags);
+		*(long *)ll = *(long *)ll_pool.cur;
+		*(long *)ll_pool.cur = (long)ll;
+		ll_pool.count++;
+		spin_unlock_irqrestore(&ll_lock, flags);
+	}
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_free_ll_entry);
+
+void pnx4008_free_ll(u32 ll_dma, struct pnx4008_dma_ll * ll)
+{
+	struct pnx4008_dma_ll *ptr;
+	u32 dma;
+
+	while (ll) {
+		dma = ll->next_dma;
+		ptr = ll->next;
+		pnx4008_free_ll_entry(ll, ll_dma);
+
+		ll_dma = dma;
+		ll = ptr;
+	}
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_free_ll);
+
+static int dma_channels_requested = 0;
+
+static inline void dma_increment_usage(void)
+{
+	if (!dma_channels_requested++) {
+		struct clk *clk = clk_get(0, "dma_ck");
+		if (!IS_ERR(clk)) {
+			clk_set_rate(clk, 1);
+			clk_put(clk);
+		}
+		pnx4008_config_dma(-1, -1, 1);
+	}
+}
+static inline void dma_decrement_usage(void)
+{
+	if (!--dma_channels_requested) {
+		struct clk *clk = clk_get(0, "dma_ck");
+		if (!IS_ERR(clk)) {
+			clk_set_rate(clk, 0);
+			clk_put(clk);
+		}
+		pnx4008_config_dma(-1, -1, 0);
+
+	}
+}
+
+static spinlock_t dma_lock = SPIN_LOCK_UNLOCKED;
+
+static inline void pnx4008_dma_lock(void)
+{
+	spin_lock_irq(&dma_lock);
+}
+
+static inline void pnx4008_dma_unlock(void)
+{
+	spin_unlock_irq(&dma_lock);
+}
+
+#define VALID_CHANNEL(c)	(((c) >= 0) && ((c) < MAX_DMA_CHANNELS))
+
+int pnx4008_request_channel(char *name, int ch,
+			    void (*irq_handler) (int, int, void *,
+						 struct pt_regs *), void *data)
+{
+	int i, found = 0;
+
+	/* basic sanity checks */
+	if (!name || (ch != -1 && !VALID_CHANNEL(ch)))
+		return -EINVAL;
+
+	pnx4008_dma_lock();
+
+	/* try grabbing a DMA channel with the requested priority */
+	for (i = MAX_DMA_CHANNELS - 1; i >= 0; i--) {
+		if (!dma_channels[i].name && (ch == -1 || ch == i)) {
+			found = 1;
+			break;
+		}
+	}
+
+	if (found) {
+		dma_increment_usage();
+		dma_channels[i].name = name;
+		dma_channels[i].irq_handler = irq_handler;
+		dma_channels[i].data = data;
+		dma_channels[i].ll = NULL;
+		dma_channels[i].ll_dma = 0;
+	} else {
+		printk(KERN_WARNING "No more available DMA channels for %s\n",
+		       name);
+		i = -ENODEV;
+	}
+
+	pnx4008_dma_unlock();
+	return i;
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_request_channel);
+
+void pnx4008_free_channel(int ch)
+{
+	if (!dma_channels[ch].name) {
+		printk(KERN_CRIT
+		       "%s: trying to free channel %d which is already freed\n",
+		       __FUNCTION__, ch);
+		return;
+	}
+
+	pnx4008_dma_lock();
+	pnx4008_free_ll(dma_channels[ch].ll_dma, dma_channels[ch].ll);
+	dma_channels[ch].ll = NULL;
+	dma_decrement_usage();
+
+	dma_channels[ch].name = NULL;
+	pnx4008_dma_unlock();
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_free_channel);
+
+int pnx4008_config_dma(int ahb_m1_be, int ahb_m2_be, int enable)
+{
+	unsigned long dma_cfg = __raw_readl(DMAC_CONFIG);
+
+	switch (ahb_m1_be) {
+	case 0:
+		dma_cfg &= ~(1 << 1);
+		break;
+	case 1:
+		dma_cfg |= (1 << 1);
+		break;
+	default:
+		break;
+	}
+
+	switch (ahb_m2_be) {
+	case 0:
+		dma_cfg &= ~(1 << 2);
+		break;
+	case 1:
+		dma_cfg |= (1 << 2);
+		break;
+	default:
+		break;
+	}
+
+	switch (enable) {
+	case 0:
+		dma_cfg &= ~(1 << 0);
+		break;
+	case 1:
+		dma_cfg |= (1 << 0);
+		break;
+	default:
+		break;
+	}
+
+	pnx4008_dma_lock();
+	__raw_writel(dma_cfg, DMAC_CONFIG);
+	pnx4008_dma_unlock();
+
+	return 0;
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_config_dma);
+
+int pnx4008_dma_pack_control(const struct pnx4008_dma_ch_ctrl * ch_ctrl,
+			     unsigned long *ctrl)
+{
+	int i = 0, dbsize, sbsize, err = 0;
+
+	if (!ctrl || !ch_ctrl) {
+		err = -EINVAL;
+		goto out;
+	}
+
+	*ctrl = 0;
+
+	switch (ch_ctrl->tc_mask) {
+	case 0:
+		break;
+	case 1:
+		*ctrl |= (1 << 31);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+
+	switch (ch_ctrl->cacheable) {
+	case 0:
+		break;
+	case 1:
+		*ctrl |= (1 << 30);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_ctrl->bufferable) {
+	case 0:
+		break;
+	case 1:
+		*ctrl |= (1 << 29);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_ctrl->priv_mode) {
+	case 0:
+		break;
+	case 1:
+		*ctrl |= (1 << 28);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_ctrl->di) {
+	case 0:
+		break;
+	case 1:
+		*ctrl |= (1 << 27);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_ctrl->si) {
+	case 0:
+		break;
+	case 1:
+		*ctrl |= (1 << 26);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_ctrl->dest_ahb1) {
+	case 0:
+		break;
+	case 1:
+		*ctrl |= (1 << 25);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_ctrl->src_ahb1) {
+	case 0:
+		break;
+	case 1:
+		*ctrl |= (1 << 24);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_ctrl->dwidth) {
+	case WIDTH_BYTE:
+		*ctrl &= ~(7 << 21);
+		break;
+	case WIDTH_HWORD:
+		*ctrl &= ~(7 << 21);
+		*ctrl |= (1 << 21);
+		break;
+	case WIDTH_WORD:
+		*ctrl &= ~(7 << 21);
+		*ctrl |= (2 << 21);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_ctrl->swidth) {
+	case WIDTH_BYTE:
+		*ctrl &= ~(7 << 18);
+		break;
+	case WIDTH_HWORD:
+		*ctrl &= ~(7 << 18);
+		*ctrl |= (1 << 18);
+		break;
+	case WIDTH_WORD:
+		*ctrl &= ~(7 << 18);
+		*ctrl |= (2 << 18);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	dbsize = ch_ctrl->dbsize;
+	while (!(dbsize & 1)) {
+		i++;
+		dbsize >>= 1;
+	}
+	if (ch_ctrl->dbsize != 1 || i > 8 || i == 1) {
+		err = -EINVAL;
+		goto out;
+	} else if (i > 1)
+		i--;
+	*ctrl &= ~(7 << 15);
+	*ctrl |= (i << 15);
+
+	sbsize = ch_ctrl->sbsize;
+	while (!(sbsize & 1)) {
+		i++;
+		sbsize >>= 1;
+	}
+	if (ch_ctrl->sbsize != 1 || i > 8 || i == 1) {
+		err = -EINVAL;
+		goto out;
+	} else if (i > 1)
+		i--;
+	*ctrl &= ~(7 << 12);
+	*ctrl |= (i << 12);
+
+	if (ch_ctrl->tr_size > 0x7ff) {
+		err = -E2BIG;
+		goto out;
+	}
+	*ctrl &= ~0x7ff;
+	*ctrl |= ch_ctrl->tr_size & 0x7ff;
+
+out:
+	return err;
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_dma_pack_control);
+
+int pnx4008_dma_parse_control(unsigned long ctrl,
+			      struct pnx4008_dma_ch_ctrl * ch_ctrl)
+{
+	int err = 0;
+
+	if (!ch_ctrl) {
+		err = -EINVAL;
+		goto out;
+	}
+
+	ch_ctrl->tr_size = ctrl & 0x7ff;
+	ctrl >>= 12;
+
+	ch_ctrl->sbsize = 1 << (ctrl & 7);
+	if (ch_ctrl->sbsize > 1)
+		ch_ctrl->sbsize <<= 1;
+	ctrl >>= 3;
+
+	ch_ctrl->dbsize = 1 << (ctrl & 7);
+	if (ch_ctrl->dbsize > 1)
+		ch_ctrl->dbsize <<= 1;
+	ctrl >>= 3;
+
+	switch (ctrl & 7) {
+	case 0:
+		ch_ctrl->swidth = WIDTH_BYTE;
+		break;
+	case 1:
+		ch_ctrl->swidth = WIDTH_HWORD;
+		break;
+	case 2:
+		ch_ctrl->swidth = WIDTH_WORD;
+		break;
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	ctrl >>= 3;
+
+	switch (ctrl & 7) {
+	case 0:
+		ch_ctrl->dwidth = WIDTH_BYTE;
+		break;
+	case 1:
+		ch_ctrl->dwidth = WIDTH_HWORD;
+		break;
+	case 2:
+		ch_ctrl->dwidth = WIDTH_WORD;
+		break;
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	ctrl >>= 3;
+
+	ch_ctrl->src_ahb1 = ctrl & 1;
+	ctrl >>= 1;
+
+	ch_ctrl->dest_ahb1 = ctrl & 1;
+	ctrl >>= 1;
+
+	ch_ctrl->si = ctrl & 1;
+	ctrl >>= 1;
+
+	ch_ctrl->di = ctrl & 1;
+	ctrl >>= 1;
+
+	ch_ctrl->priv_mode = ctrl & 1;
+	ctrl >>= 1;
+
+	ch_ctrl->bufferable = ctrl & 1;
+	ctrl >>= 1;
+
+	ch_ctrl->cacheable = ctrl & 1;
+	ctrl >>= 1;
+
+	ch_ctrl->tc_mask = ctrl & 1;
+
+out:
+	return err;
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_dma_parse_control);
+
+int pnx4008_dma_pack_config(const struct pnx4008_dma_ch_config * ch_cfg,
+			    unsigned long *cfg)
+{
+	int err = 0;
+
+	if (!cfg || !ch_cfg) {
+		err = -EINVAL;
+		goto out;
+	}
+
+	*cfg = 0;
+
+	switch (ch_cfg->halt) {
+	case 0:
+		break;
+	case 1:
+		*cfg |= (1 << 18);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_cfg->active) {
+	case 0:
+		break;
+	case 1:
+		*cfg |= (1 << 17);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_cfg->lock) {
+	case 0:
+		break;
+	case 1:
+		*cfg |= (1 << 16);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_cfg->itc) {
+	case 0:
+		break;
+	case 1:
+		*cfg |= (1 << 15);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_cfg->ie) {
+	case 0:
+		break;
+	case 1:
+		*cfg |= (1 << 14);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	switch (ch_cfg->flow_cntrl) {
+	case FC_MEM2MEM_DMA:
+		*cfg &= ~(7 << 11);
+		break;
+	case FC_MEM2PER_DMA:
+		*cfg &= ~(7 << 11);
+		*cfg |= (1 << 11);
+		break;
+	case FC_PER2MEM_DMA:
+		*cfg &= ~(7 << 11);
+		*cfg |= (2 << 11);
+		break;
+	case FC_PER2PER_DMA:
+		*cfg &= ~(7 << 11);
+		*cfg |= (3 << 11);
+		break;
+	case FC_PER2PER_DPER:
+		*cfg &= ~(7 << 11);
+		*cfg |= (4 << 11);
+		break;
+	case FC_MEM2PER_PER:
+		*cfg &= ~(7 << 11);
+		*cfg |= (5 << 11);
+		break;
+	case FC_PER2MEM_PER:
+		*cfg &= ~(7 << 11);
+		*cfg |= (6 << 11);
+		break;
+	case FC_PER2PER_SPER:
+		*cfg |= (7 << 11);
+		break;
+
+	default:
+		err = -EINVAL;
+		goto out;
+	}
+	*cfg &= ~(0x1f << 6);
+	*cfg |= ((ch_cfg->dest_per & 0x1f) << 6);
+
+	*cfg &= ~(0x1f << 1);
+	*cfg |= ((ch_cfg->src_per & 0x1f) << 1);
+
+out:
+	return err;
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_dma_pack_config);
+
+int pnx4008_dma_parse_config(unsigned long cfg,
+			     struct pnx4008_dma_ch_config * ch_cfg)
+{
+	int err = 0;
+
+	if (!ch_cfg) {
+		err = -EINVAL;
+		goto out;
+	}
+
+	cfg >>= 1;
+
+	ch_cfg->src_per = cfg & 0x1f;
+	cfg >>= 5;
+
+	ch_cfg->dest_per = cfg & 0x1f;
+	cfg >>= 5;
+
+	switch (cfg & 7) {
+	case 0:
+		ch_cfg->flow_cntrl = FC_MEM2MEM_DMA;
+		break;
+	case 1:
+		ch_cfg->flow_cntrl = FC_MEM2PER_DMA;
+		break;
+	case 2:
+		ch_cfg->flow_cntrl = FC_PER2MEM_DMA;
+		break;
+	case 3:
+		ch_cfg->flow_cntrl = FC_PER2PER_DMA;
+		break;
+	case 4:
+		ch_cfg->flow_cntrl = FC_PER2PER_DPER;
+		break;
+	case 5:
+		ch_cfg->flow_cntrl = FC_MEM2PER_PER;
+		break;
+	case 6:
+		ch_cfg->flow_cntrl = FC_PER2MEM_PER;
+		break;
+	case 7:
+		ch_cfg->flow_cntrl = FC_PER2PER_SPER;
+	}
+	cfg >>= 3;
+
+	ch_cfg->ie = cfg & 1;
+	cfg >>= 1;
+
+	ch_cfg->itc = cfg & 1;
+	cfg >>= 1;
+
+	ch_cfg->lock = cfg & 1;
+	cfg >>= 1;
+
+	ch_cfg->active = cfg & 1;
+	cfg >>= 1;
+
+	ch_cfg->halt = cfg & 1;
+
+out:
+	return err;
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_dma_parse_config);
+
+void pnx4008_dma_split_head_entry(struct pnx4008_dma_config * config,
+				  struct pnx4008_dma_ch_ctrl * ctrl)
+{
+	int new_len = ctrl->tr_size, num_entries = 0;
+	int old_len = new_len;
+	int src_width, dest_width, count = 1;
+
+	switch (ctrl->swidth) {
+	case WIDTH_BYTE:
+		src_width = 1;
+		break;
+	case WIDTH_HWORD:
+		src_width = 2;
+		break;
+	case WIDTH_WORD:
+		src_width = 4;
+		break;
+	default:
+		return;
+	}
+
+	switch (ctrl->dwidth) {
+	case WIDTH_BYTE:
+		dest_width = 1;
+		break;
+	case WIDTH_HWORD:
+		dest_width = 2;
+		break;
+	case WIDTH_WORD:
+		dest_width = 4;
+		break;
+	default:
+		return;
+	}
+
+	while (new_len > 0x7FF) {
+		num_entries++;
+		new_len = (ctrl->tr_size + num_entries) / (num_entries + 1);
+	}
+	if (num_entries != 0) {
+		struct pnx4008_dma_ll *ll = NULL;
+		config->ch_ctrl &= ~0x7ff;
+		config->ch_ctrl |= new_len;
+		if (!config->is_ll) {
+			config->is_ll = 1;
+			while (num_entries) {
+				if (!ll) {
+					config->ll =
+					    pnx4008_alloc_ll_entry(&config->
+								   ll_dma);
+					ll = config->ll;
+				} else {
+					ll->next =
+					    pnx4008_alloc_ll_entry(&ll->
+								   next_dma);
+					ll = ll->next;
+				}
+
+				if (ctrl->si)
+					ll->src_addr =
+					    config->src_addr +
+					    src_width * new_len * count;
+				else
+					ll->src_addr = config->src_addr;
+				if (ctrl->di)
+					ll->dest_addr =
+					    config->dest_addr +
+					    dest_width * new_len * count;
+				else
+					ll->dest_addr = config->dest_addr;
+				ll->ch_ctrl = config->ch_ctrl & 0x7fffffff;
+				ll->next_dma = 0;
+				ll->next = NULL;
+				num_entries--;
+				count++;
+			}
+		} else {
+			struct pnx4008_dma_ll *ll_old = config->ll;
+			unsigned long ll_dma_old = config->ll_dma;
+			while (num_entries) {
+				if (!ll) {
+					config->ll =
+					    pnx4008_alloc_ll_entry(&config->
+								   ll_dma);
+					ll = config->ll;
+				} else {
+					ll->next =
+					    pnx4008_alloc_ll_entry(&ll->
+								   next_dma);
+					ll = ll->next;
+				}
+
+				if (ctrl->si)
+					ll->src_addr =
+					    config->src_addr +
+					    src_width * new_len * count;
+				else
+					ll->src_addr = config->src_addr;
+				if (ctrl->di)
+					ll->dest_addr =
+					    config->dest_addr +
+					    dest_width * new_len * count;
+				else
+					ll->dest_addr = config->dest_addr;
+				ll->ch_ctrl = config->ch_ctrl & 0x7fffffff;
+				ll->next_dma = 0;
+				ll->next = NULL;
+				num_entries--;
+				count++;
+			}
+			ll->next_dma = ll_dma_old;
+			ll->next = ll_old;
+		}
+		/* adjust last length/tc */
+		ll->ch_ctrl = config->ch_ctrl & (~0x7ff);
+		ll->ch_ctrl |= old_len - new_len * (count - 1);
+		config->ch_ctrl &= 0x7fffffff;
+	}
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_dma_split_head_entry);
+
+void pnx4008_dma_split_ll_entry(struct pnx4008_dma_ll * cur_ll,
+				struct pnx4008_dma_ch_ctrl * ctrl)
+{
+	int new_len = ctrl->tr_size, num_entries = 0;
+	int old_len = new_len;
+	int src_width, dest_width, count = 1;
+
+	switch (ctrl->swidth) {
+	case WIDTH_BYTE:
+		src_width = 1;
+		break;
+	case WIDTH_HWORD:
+		src_width = 2;
+		break;
+	case WIDTH_WORD:
+		src_width = 4;
+		break;
+	default:
+		return;
+	}
+
+	switch (ctrl->dwidth) {
+	case WIDTH_BYTE:
+		dest_width = 1;
+		break;
+	case WIDTH_HWORD:
+		dest_width = 2;
+		break;
+	case WIDTH_WORD:
+		dest_width = 4;
+		break;
+	default:
+		return;
+	}
+
+	while (new_len > 0x7FF) {
+		num_entries++;
+		new_len = (ctrl->tr_size + num_entries) / (num_entries + 1);
+	}
+	if (num_entries != 0) {
+		struct pnx4008_dma_ll *ll = NULL;
+		cur_ll->ch_ctrl &= ~0x7ff;
+		cur_ll->ch_ctrl |= new_len;
+		if (!cur_ll->next) {
+			while (num_entries) {
+				if (!ll) {
+					cur_ll->next =
+					    pnx4008_alloc_ll_entry(&cur_ll->
+								   next_dma);
+					ll = cur_ll->next;
+				} else {
+					ll->next =
+					    pnx4008_alloc_ll_entry(&ll->
+								   next_dma);
+					ll = ll->next;
+				}
+
+				if (ctrl->si)
+					ll->src_addr =
+					    cur_ll->src_addr +
+					    src_width * new_len * count;
+				else
+					ll->src_addr = cur_ll->src_addr;
+				if (ctrl->di)
+					ll->dest_addr =
+					    cur_ll->dest_addr +
+					    dest_width * new_len * count;
+				else
+					ll->dest_addr = cur_ll->dest_addr;
+				ll->ch_ctrl = cur_ll->ch_ctrl & 0x7fffffff;
+				ll->next_dma = 0;
+				ll->next = NULL;
+				num_entries--;
+				count++;
+			}
+		} else {
+			struct pnx4008_dma_ll *ll_old = cur_ll->next;
+			unsigned long ll_dma_old = cur_ll->next_dma;
+			while (num_entries) {
+				if (!ll) {
+					cur_ll->next =
+					    pnx4008_alloc_ll_entry(&cur_ll->
+								   next_dma);
+					ll = cur_ll->next;
+				} else {
+					ll->next =
+					    pnx4008_alloc_ll_entry(&ll->
+								   next_dma);
+					ll = ll->next;
+				}
+
+				if (ctrl->si)
+					ll->src_addr =
+					    cur_ll->src_addr +
+					    src_width * new_len * count;
+				else
+					ll->src_addr = cur_ll->src_addr;
+				if (ctrl->di)
+					ll->dest_addr =
+					    cur_ll->dest_addr +
+					    dest_width * new_len * count;
+				else
+					ll->dest_addr = cur_ll->dest_addr;
+				ll->ch_ctrl = cur_ll->ch_ctrl & 0x7fffffff;
+				ll->next_dma = 0;
+				ll->next = NULL;
+				num_entries--;
+				count++;
+			}
+
+			ll->next_dma = ll_dma_old;
+			ll->next = ll_old;
+		}
+		/* adjust last length/tc */
+		ll->ch_ctrl = cur_ll->ch_ctrl & (~0x7ff);
+		ll->ch_ctrl |= old_len - new_len * (count - 1);
+		cur_ll->ch_ctrl &= 0x7fffffff;
+	}
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_dma_split_ll_entry);
+
+int pnx4008_config_channel(int ch, struct pnx4008_dma_config * config)
+{
+	if (!VALID_CHANNEL(ch) || !dma_channels[ch].name)
+		return -EINVAL;
+
+	pnx4008_dma_lock();
+	__raw_writel(config->src_addr, DMAC_Cx_SRC_ADDR(ch));
+	__raw_writel(config->dest_addr, DMAC_Cx_DEST_ADDR(ch));
+
+	if (config->is_ll)
+		__raw_writel(config->ll_dma, DMAC_Cx_LLI(ch));
+	else
+		__raw_writel(0, DMAC_Cx_LLI(ch));
+
+	__raw_writel(config->ch_ctrl, DMAC_Cx_CONTROL(ch));
+	__raw_writel(config->ch_cfg, DMAC_Cx_CONFIG(ch));
+	pnx4008_dma_unlock();
+
+	return 0;
+
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_config_channel);
+
+int pnx4008_channel_get_config(int ch, struct pnx4008_dma_config * config)
+{
+	if (!VALID_CHANNEL(ch) || !dma_channels[ch].name || !config)
+		return -EINVAL;
+
+	pnx4008_dma_lock();
+	config->ch_cfg = __raw_readl(DMAC_Cx_CONFIG(ch));
+	config->ch_ctrl = __raw_readl(DMAC_Cx_CONTROL(ch));
+
+	config->ll_dma = __raw_readl(DMAC_Cx_LLI(ch));
+	config->is_ll = config->ll_dma ? 1 : 0;
+
+	config->src_addr = __raw_readl(DMAC_Cx_SRC_ADDR(ch));
+	config->dest_addr = __raw_readl(DMAC_Cx_DEST_ADDR(ch));
+	pnx4008_dma_unlock();
+
+	return 0;
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_channel_get_config);
+
+int pnx4008_dma_ch_enable(int ch)
+{
+	unsigned long ch_cfg;
+
+	if (!VALID_CHANNEL(ch) || !dma_channels[ch].name)
+		return -EINVAL;
+
+	pnx4008_dma_lock();
+	ch_cfg = __raw_readl(DMAC_Cx_CONFIG(ch));
+	ch_cfg |= 1;
+	__raw_writel(ch_cfg, DMAC_Cx_CONFIG(ch));
+	pnx4008_dma_unlock();
+
+	return 0;
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_dma_ch_enable);
+
+int pnx4008_dma_ch_disable(int ch)
+{
+	unsigned long ch_cfg;
+
+	if (!VALID_CHANNEL(ch) || !dma_channels[ch].name)
+		return -EINVAL;
+
+	pnx4008_dma_lock();
+	ch_cfg = __raw_readl(DMAC_Cx_CONFIG(ch));
+	ch_cfg &= ~1;
+	__raw_writel(ch_cfg, DMAC_Cx_CONFIG(ch));
+	pnx4008_dma_unlock();
+
+	return 0;
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_dma_ch_disable);
+
+int pnx4008_dma_ch_enabled(int ch)
+{
+	unsigned long ch_cfg;
+
+	if (!VALID_CHANNEL(ch) || !dma_channels[ch].name)
+		return -EINVAL;
+
+	pnx4008_dma_lock();
+	ch_cfg = __raw_readl(DMAC_Cx_CONFIG(ch));
+	pnx4008_dma_unlock();
+
+	return ch_cfg & 1;
+}
+
+EXPORT_SYMBOL_GPL(pnx4008_dma_ch_enabled);
+
+static irqreturn_t dma_irq_handler(int irq, void *dev_id, struct pt_regs *regs)
+{
+	int i;
+	unsigned long dint = __raw_readl(DMAC_INT_STAT);
+	unsigned long tcint = __raw_readl(DMAC_INT_TC_STAT);
+	unsigned long eint = __raw_readl(DMAC_INT_ERR_STAT);
+	unsigned long i_bit;
+
+	for (i = MAX_DMA_CHANNELS - 1; i >= 0; i--) {
+		i_bit = 1 << i;
+		if (dint & i_bit) {
+			struct dma_channel *channel = &dma_channels[i];
+
+			if (channel->name && channel->irq_handler) {
+				int cause = 0;
+
+				if (eint & i_bit)
+					cause |= DMA_ERR_INT;
+				if (tcint & i_bit)
+					cause |= DMA_TC_INT;
+				channel->irq_handler(i, cause, channel->data,
+						     regs);
+			} else {
+				/*
+				 * IRQ for an unregistered DMA channel
+				 */
+				printk(KERN_WARNING
+				       "spurious IRQ for DMA channel %d\n", i);
+			}
+			if (tcint & i_bit)
+				__raw_writel(i_bit, DMAC_INT_TC_CLEAR);
+			if (eint & i_bit)
+				__raw_writel(i_bit, DMAC_INT_ERR_CLEAR);
+		}
+	}
+	return IRQ_HANDLED;
+}
+
+static int __init pnx4008_dma_init(void)
+{
+	int ret, i;
+
+	ret = request_irq(DMA_INT, dma_irq_handler, 0, "DMA", NULL);
+	if (ret) {
+		printk(KERN_CRIT "Wow!  Can't register IRQ for DMA\n");
+		goto out;
+	}
+
+	ll_pool.count = 0x4000 / sizeof(struct pnx4008_dma_ll);
+	ll_pool.cur = ll_pool.vaddr =
+	    dma_alloc_coherent(NULL, ll_pool.count * sizeof(struct pnx4008_dma_ll),
+			       &ll_pool.dma_addr, GFP_KERNEL);
+
+	if (!ll_pool.vaddr) {
+		ret = -ENOMEM;
+		free_irq(DMA_INT, NULL);
+		goto out;
+	}
+
+	for (i = 0; i < ll_pool.count - 1; i++) {
+		void **addr = ll_pool.vaddr + i * sizeof(struct pnx4008_dma_ll);
+		*addr = (void *)addr + sizeof(struct pnx4008_dma_ll);
+	}
+	*(long *)(ll_pool.vaddr +
+		  (ll_pool.count - 1) * sizeof(struct pnx4008_dma_ll)) =
+	    (long)ll_pool.vaddr;
+
+	__raw_writel(1, DMAC_CONFIG);
+
+out:
+	return ret;
+}
+arch_initcall(pnx4008_dma_init);
diff --git a/arch/arm/mach-pnx4008/gpio.c b/arch/arm/mach-pnx4008/gpio.c
new file mode 100644
index 0000000..e1ce050
--- /dev/null
+++ b/arch/arm/mach-pnx4008/gpio.c
@@ -0,0 +1,330 @@
+/*
+ * arch/arm/mach-pnx4008/gpio.c
+ *
+ * PNX4008 GPIO driver
+ *
+ * Author: Dmitry Chigirev <source@mvista.com>
+ *
+ * Based on reference code by Iwo Mergler and Z.Tabaaloute from Philips:
+ * Copyright (c) 2005 Koninklijke Philips Electronics N.V.
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#include <linux/config.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <asm/semaphore.h>
+#include <asm/io.h>
+#include <asm/arch/platform.h>
+#include <asm/arch/gpio.h>
+
+/* register definitions */
+#define PIO_VA_BASE	IO_ADDRESS(PNX4008_PIO_BASE)
+
+#define PIO_INP_STATE	(0x00U)
+#define PIO_OUTP_SET	(0x04U)
+#define PIO_OUTP_CLR	(0x08U)
+#define PIO_OUTP_STATE	(0x0CU)
+#define PIO_DRV_SET	(0x10U)
+#define PIO_DRV_CLR	(0x14U)
+#define PIO_DRV_STATE	(0x18U)
+#define PIO_SDINP_STATE	(0x1CU)
+#define PIO_SDOUTP_SET	(0x20U)
+#define PIO_SDOUTP_CLR	(0x24U)
+#define PIO_MUX_SET	(0x28U)
+#define PIO_MUX_CLR	(0x2CU)
+#define PIO_MUX_STATE	(0x30U)
+
+static inline void gpio_lock(void)
+{
+	local_irq_disable();
+}
+
+static inline void gpio_unlock(void)
+{
+	local_irq_enable();
+}
+
+/* Inline functions */
+static inline int gpio_read_bit(u32 reg, int gpio)
+{
+	u32 bit, val;
+	int ret = -EFAULT;
+
+	if (gpio < 0)
+		goto out;
+
+	bit = GPIO_BIT(gpio);
+	if (bit) {
+		val = __raw_readl(PIO_VA_BASE + reg);
+		ret = (val & bit) ? 1 : 0;
+	}
+out:
+	return ret;
+}
+
+static inline int gpio_set_bit(u32 reg, int gpio)
+{
+	u32 bit, val;
+	int ret = -EFAULT;
+
+	if (gpio < 0)
+		goto out;
+
+	bit = GPIO_BIT(gpio);
+	if (bit) {
+		val = __raw_readl(PIO_VA_BASE + reg);
+		val |= bit;
+		__raw_writel(val, PIO_VA_BASE + reg);
+		ret = 0;
+	}
+out:
+	return ret;
+}
+
+/* Very simple access control, bitmap for allocated/free */
+static unsigned long access_map[4];
+#define INP_INDEX	0
+#define OUTP_INDEX	1
+#define GPIO_INDEX	2
+#define MUX_INDEX	3
+
+/*GPIO to Input Mapping */
+static short gpio_to_inp_map[32] = {
+	-1, -1, -1, -1, -1, -1, -1, -1,
+	-1, -1, -1, -1, -1, -1, -1, -1,
+	-1, -1, -1, -1, -1, -1, -1, -1,
+	-1, 10, 11, 12, 13, 14, 24, -1
+};
+
+/*GPIO to Mux Mapping */
+static short gpio_to_mux_map[32] = {
+	-1, -1, -1, -1, -1, -1, -1, -1,
+	-1, -1, -1, -1, -1, -1, -1, -1,
+	-1, -1, -1, -1, -1, -1, -1, -1,
+	-1, -1, -1, 0, 1, 4, 5, -1
+};
+
+/*Output to Mux Mapping */
+static short outp_to_mux_map[32] = {
+	-1, -1, -1, 6, -1, -1, -1, -1,
+	-1, -1, -1, -1, -1, -1, -1, -1,
+	-1, -1, -1, -1, -1, 2, -1, -1,
+	-1, -1, -1, -1, -1, -1, -1, -1
+};
+
+int pnx4008_gpio_register_pin(unsigned short pin)
+{
+	unsigned long bit = GPIO_BIT(pin);
+	int ret = -EBUSY;	/* Already in use */
+
+	gpio_lock();
+
+	if (GPIO_ISBID(pin)) {
+		if (access_map[GPIO_INDEX] & bit)
+			goto out;
+		access_map[GPIO_INDEX] |= bit;
+
+	} else if (GPIO_ISRAM(pin)) {
+		if (access_map[GPIO_INDEX] & bit)
+			goto out;
+		access_map[GPIO_INDEX] |= bit;
+
+	} else if (GPIO_ISMUX(pin)) {
+		if (access_map[MUX_INDEX] & bit)
+			goto out;
+		access_map[MUX_INDEX] |= bit;
+
+	} else if (GPIO_ISOUT(pin)) {
+		if (access_map[OUTP_INDEX] & bit)
+			goto out;
+		access_map[OUTP_INDEX] |= bit;
+
+	} else if (GPIO_ISIN(pin)) {
+		if (access_map[INP_INDEX] & bit)
+			goto out;
+		access_map[INP_INDEX] |= bit;
+	} else
+		goto out;
+	ret = 0;
+
+out:
+	gpio_unlock();
+	return ret;
+}
+
+EXPORT_SYMBOL(pnx4008_gpio_register_pin);
+
+int pnx4008_gpio_unregister_pin(unsigned short pin)
+{
+	unsigned long bit = GPIO_BIT(pin);
+	int ret = -EFAULT;	/* Not registered */
+
+	gpio_lock();
+
+	if (GPIO_ISBID(pin)) {
+		if (~access_map[GPIO_INDEX] & bit)
+			goto out;
+		access_map[GPIO_INDEX] &= ~bit;
+	} else if (GPIO_ISRAM(pin)) {
+		if (~access_map[GPIO_INDEX] & bit)
+			goto out;
+		access_map[GPIO_INDEX] &= ~bit;
+	} else if (GPIO_ISMUX(pin)) {
+		if (~access_map[MUX_INDEX] & bit)
+			goto out;
+		access_map[MUX_INDEX] &= ~bit;
+	} else if (GPIO_ISOUT(pin)) {
+		if (~access_map[OUTP_INDEX] & bit)
+			goto out;
+		access_map[OUTP_INDEX] &= ~bit;
+	} else if (GPIO_ISIN(pin)) {
+		if (~access_map[INP_INDEX] & bit)
+			goto out;
+		access_map[INP_INDEX] &= ~bit;
+	} else
+		goto out;
+	ret = 0;
+
+out:
+	gpio_unlock();
+	return ret;
+}
+
+EXPORT_SYMBOL(pnx4008_gpio_unregister_pin);
+
+unsigned long pnx4008_gpio_read_pin(unsigned short pin)
+{
+	unsigned long ret = -EFAULT;
+	int gpio = GPIO_BIT_MASK(pin);
+	gpio_lock();
+	if (GPIO_ISOUT(pin)) {
+		ret = gpio_read_bit(PIO_OUTP_STATE, gpio);
+	} else if (GPIO_ISRAM(pin)) {
+		if (gpio_read_bit(PIO_DRV_STATE, gpio) == 0) {
+			ret = gpio_read_bit(PIO_SDINP_STATE, gpio);
+		}
+	} else if (GPIO_ISBID(pin)) {
+		ret = gpio_read_bit(PIO_DRV_STATE, gpio);
+		if (ret > 0)
+			ret = gpio_read_bit(PIO_OUTP_STATE, gpio);
+		else if (ret == 0)
+			ret =
+			    gpio_read_bit(PIO_INP_STATE, gpio_to_inp_map[gpio]);
+	} else if (GPIO_ISIN(pin)) {
+		ret = gpio_read_bit(PIO_INP_STATE, gpio);
+	}
+	gpio_unlock();
+	return ret;
+}
+
+EXPORT_SYMBOL(pnx4008_gpio_read_pin);
+
+/* Write Value to output */
+int pnx4008_gpio_write_pin(unsigned short pin, int output)
+{
+	int gpio = GPIO_BIT_MASK(pin);
+	int ret = -EFAULT;
+
+	gpio_lock();
+	if (GPIO_ISOUT(pin)) {
+		printk( "writing '%x' to '%x'\n",
+				gpio, output ? PIO_OUTP_SET : PIO_OUTP_CLR );
+		ret = gpio_set_bit(output ? PIO_OUTP_SET : PIO_OUTP_CLR, gpio);
+	} else if (GPIO_ISRAM(pin)) {
+		if (gpio_read_bit(PIO_DRV_STATE, gpio) > 0)
+			ret = gpio_set_bit(output ? PIO_SDOUTP_SET :
+					   PIO_SDOUTP_CLR, gpio);
+	} else if (GPIO_ISBID(pin)) {
+		if (gpio_read_bit(PIO_DRV_STATE, gpio) > 0)
+			ret = gpio_set_bit(output ? PIO_OUTP_SET :
+					   PIO_OUTP_CLR, gpio);
+	}
+	gpio_unlock();
+	return ret;
+}
+
+EXPORT_SYMBOL(pnx4008_gpio_write_pin);
+
+/* Value = 1 : Set GPIO pin as output */
+/* Value = 0 : Set GPIO pin as input */
+int pnx4008_gpio_set_pin_direction(unsigned short pin, int output)
+{
+	int gpio = GPIO_BIT_MASK(pin);
+	int ret = -EFAULT;
+
+	gpio_lock();
+	if (GPIO_ISBID(pin) || GPIO_ISRAM(pin)) {
+		ret = gpio_set_bit(output ? PIO_DRV_SET : PIO_DRV_CLR, gpio);
+	}
+	gpio_unlock();
+	return ret;
+}
+
+EXPORT_SYMBOL(pnx4008_gpio_set_pin_direction);
+
+/* Read GPIO pin direction: 0= pin used as input, 1= pin used as output*/
+int pnx4008_gpio_read_pin_direction(unsigned short pin)
+{
+	int gpio = GPIO_BIT_MASK(pin);
+	int ret = -EFAULT;
+
+	gpio_lock();
+	if (GPIO_ISBID(pin) || GPIO_ISRAM(pin)) {
+		ret = gpio_read_bit(PIO_DRV_STATE, gpio);
+	}
+	gpio_unlock();
+	return ret;
+}
+
+EXPORT_SYMBOL(pnx4008_gpio_read_pin_direction);
+
+/* Value = 1 : Set pin to muxed function  */
+/* Value = 0 : Set pin as GPIO */
+int pnx4008_gpio_set_pin_mux(unsigned short pin, int output)
+{
+	int gpio = GPIO_BIT_MASK(pin);
+	int ret = -EFAULT;
+
+	gpio_lock();
+	if (GPIO_ISBID(pin)) {
+		ret =
+		    gpio_set_bit(output ? PIO_MUX_SET : PIO_MUX_CLR,
+				 gpio_to_mux_map[gpio]);
+	} else if (GPIO_ISOUT(pin)) {
+		ret =
+		    gpio_set_bit(output ? PIO_MUX_SET : PIO_MUX_CLR,
+				 outp_to_mux_map[gpio]);
+	} else if (GPIO_ISMUX(pin)) {
+		ret = gpio_set_bit(output ? PIO_MUX_SET : PIO_MUX_CLR, gpio);
+	}
+	gpio_unlock();
+	return ret;
+}
+
+EXPORT_SYMBOL(pnx4008_gpio_set_pin_mux);
+
+/* Read pin mux function: 0= pin used as GPIO, 1= pin used for muxed function*/
+int pnx4008_gpio_read_pin_mux(unsigned short pin)
+{
+	int gpio = GPIO_BIT_MASK(pin);
+	int ret = -EFAULT;
+
+	gpio_lock();
+	if (GPIO_ISBID(pin)) {
+		ret = gpio_read_bit(PIO_MUX_STATE, gpio_to_mux_map[gpio]);
+	} else if (GPIO_ISOUT(pin)) {
+		ret = gpio_read_bit(PIO_MUX_STATE, outp_to_mux_map[gpio]);
+	} else if (GPIO_ISMUX(pin)) {
+		ret = gpio_read_bit(PIO_MUX_STATE, gpio);
+	}
+	gpio_unlock();
+	return ret;
+}
+
+EXPORT_SYMBOL(pnx4008_gpio_read_pin_mux);
diff --git a/arch/arm/mach-pnx4008/irq.c b/arch/arm/mach-pnx4008/irq.c
new file mode 100644
index 0000000..9b0a8e0
--- /dev/null
+++ b/arch/arm/mach-pnx4008/irq.c
@@ -0,0 +1,121 @@
+/*
+ * arch/arm/mach-pnx4008/irq.c
+ *
+ * PNX4008 IRQ controller driver
+ *
+ * Author: Dmitry Chigirev <source@mvista.com>
+ *
+ * Based on reference code received from Philips:
+ * Copyright (C) 2003 Philips Semiconductors
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/mm.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/pgtable.h>
+#include <asm/page.h>
+#include <asm/system.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/map.h>
+#include <asm/arch/irq.h>
+
+static u8 pnx4008_irq_type[NR_IRQS] = PNX4008_IRQ_TYPES;
+
+static void pnx4008_mask_irq(unsigned int irq)
+{
+	__raw_writel(__raw_readl(INTC_ER(irq)) & ~INTC_BIT(irq), INTC_ER(irq));	/* mask interrupt */
+}
+
+static void pnx4008_unmask_irq(unsigned int irq)
+{
+	__raw_writel(__raw_readl(INTC_ER(irq)) | INTC_BIT(irq), INTC_ER(irq));	/* unmask interrupt */
+}
+
+static void pnx4008_mask_ack_irq(unsigned int irq)
+{
+	__raw_writel(__raw_readl(INTC_ER(irq)) & ~INTC_BIT(irq), INTC_ER(irq));	/* mask interrupt */
+	__raw_writel(INTC_BIT(irq), INTC_SR(irq));	/* clear interrupt status */
+}
+
+static int pnx4008_set_irq_type(unsigned int irq, unsigned int type)
+{
+	switch (type) {
+	case IRQT_RISING:
+		__raw_writel(__raw_readl(INTC_ATR(irq)) | INTC_BIT(irq), INTC_ATR(irq));	/*edge sensitive */
+		__raw_writel(__raw_readl(INTC_APR(irq)) | INTC_BIT(irq), INTC_APR(irq));	/*rising edge */
+		set_irq_handler(irq, do_edge_IRQ);
+		break;
+	case IRQT_FALLING:
+		__raw_writel(__raw_readl(INTC_ATR(irq)) | INTC_BIT(irq), INTC_ATR(irq));	/*edge sensitive */
+		__raw_writel(__raw_readl(INTC_APR(irq)) & ~INTC_BIT(irq), INTC_APR(irq));	/*falling edge */
+		set_irq_handler(irq, do_edge_IRQ);
+		break;
+	case IRQT_LOW:
+		__raw_writel(__raw_readl(INTC_ATR(irq)) & ~INTC_BIT(irq), INTC_ATR(irq));	/*level sensitive */
+		__raw_writel(__raw_readl(INTC_APR(irq)) & ~INTC_BIT(irq), INTC_APR(irq));	/*low level */
+		set_irq_handler(irq, do_level_IRQ);
+		break;
+	case IRQT_HIGH:
+		__raw_writel(__raw_readl(INTC_ATR(irq)) & ~INTC_BIT(irq), INTC_ATR(irq));	/*level sensitive */
+		__raw_writel(__raw_readl(INTC_APR(irq)) | INTC_BIT(irq), INTC_APR(irq));	/* high level */
+		set_irq_handler(irq, do_level_IRQ);
+		break;
+
+	/* IRQT_BOTHEDGE is not supported */
+	default:
+		printk(KERN_ERR "PNX4008 IRQ: Unsupported irq type %d\n", type);
+		return -1;
+	}
+	return 0;
+}
+
+static struct irqchip pnx4008_irq_chip = {
+	.ack = pnx4008_mask_ack_irq,
+	.mask = pnx4008_mask_irq,
+	.unmask = pnx4008_unmask_irq,
+	.set_type = pnx4008_set_irq_type,
+};
+
+void __init pnx4008_init_irq(void)
+{
+	unsigned int i;
+
+	/* configure and enable IRQ 0,1,30,31 (cascade interrupts) mask all others */
+	pnx4008_set_irq_type(SUB1_IRQ_N, pnx4008_irq_type[SUB1_IRQ_N]);
+	pnx4008_set_irq_type(SUB2_IRQ_N, pnx4008_irq_type[SUB2_IRQ_N]);
+	pnx4008_set_irq_type(SUB1_FIQ_N, pnx4008_irq_type[SUB1_FIQ_N]);
+	pnx4008_set_irq_type(SUB2_FIQ_N, pnx4008_irq_type[SUB2_FIQ_N]);
+
+	__raw_writel((1 << SUB2_FIQ_N) | (1 << SUB1_FIQ_N) |
+			(1 << SUB2_IRQ_N) | (1 << SUB1_IRQ_N),
+		INTC_ER(MAIN_BASE_INT));
+	__raw_writel(0, INTC_ER(SIC1_BASE_INT));
+	__raw_writel(0, INTC_ER(SIC2_BASE_INT));
+
+	/* configure all other IRQ's */
+	for (i = 0; i < NR_IRQS; i++) {
+		if (i == SUB2_FIQ_N || i == SUB1_FIQ_N ||
+			i == SUB2_IRQ_N || i == SUB1_IRQ_N)
+			continue;
+		set_irq_flags(i, IRQF_VALID);
+		set_irq_chip(i, &pnx4008_irq_chip);
+		pnx4008_set_irq_type(i, pnx4008_irq_type[i]);
+	}
+}
+
diff --git a/arch/arm/mach-pnx4008/pm.c b/arch/arm/mach-pnx4008/pm.c
new file mode 100644
index 0000000..3649cd3
--- /dev/null
+++ b/arch/arm/mach-pnx4008/pm.c
@@ -0,0 +1,184 @@
+/*
+ * arch/arm/mach-pnx4008/pm.c
+ *
+ * Power Management driver for PNX4008
+ *
+ * Authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#include <linux/pm.h>
+#include <linux/rtc.h>
+#include <linux/sched.h>
+#include <linux/proc_fs.h>
+#include <linux/pm.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+
+#include <asm/io.h>
+#include <asm/mach-types.h>
+#include <asm/cacheflush.h>
+#include <asm/arch/pm.h>
+#include <asm/arch/clock.h>
+
+#define SRAM_VA IO_ADDRESS(PNX4008_IRAM_BASE)
+
+static void *saved_sram;
+
+static struct clk *pll4_clk;
+
+static inline void pnx4008_standby(void)
+{
+	void (*pnx4008_cpu_standby_ptr) (void);
+
+	local_irq_disable();
+	local_fiq_disable();
+
+	clk_disable(pll4_clk);
+
+	/*saving portion of SRAM to be used by suspend function. */
+	memcpy(saved_sram, (void *)SRAM_VA, pnx4008_cpu_standby_sz);
+
+	/*make sure SRAM copy gets physically written into SDRAM.
+	   SDRAM will be placed into self-refresh during power down */
+	flush_cache_all();
+
+	/*copy suspend function into SRAM */
+	memcpy((void *)SRAM_VA, pnx4008_cpu_standby, pnx4008_cpu_standby_sz);
+
+	/*do suspend */
+	pnx4008_cpu_standby_ptr = (void *)SRAM_VA;
+	pnx4008_cpu_standby_ptr();
+
+	/*restoring portion of SRAM that was used by suspend function */
+	memcpy((void *)SRAM_VA, saved_sram, pnx4008_cpu_standby_sz);
+
+	clk_enable(pll4_clk);
+
+	local_fiq_enable();
+	local_irq_enable();
+}
+
+static inline void pnx4008_suspend(void)
+{
+	void (*pnx4008_cpu_suspend_ptr) (void);
+
+	local_irq_disable();
+	local_fiq_disable();
+
+	clk_disable(pll4_clk);
+
+	__raw_writel(0xffffffff, START_INT_RSR_REG(SE_PIN_BASE_INT));
+	__raw_writel(0xffffffff, START_INT_RSR_REG(SE_INT_BASE_INT));
+
+	/*saving portion of SRAM to be used by suspend function. */
+	memcpy(saved_sram, (void *)SRAM_VA, pnx4008_cpu_suspend_sz);
+
+	/*make sure SRAM copy gets physically written into SDRAM.
+	   SDRAM will be placed into self-refresh during power down */
+	flush_cache_all();
+
+	/*copy suspend function into SRAM */
+	memcpy((void *)SRAM_VA, pnx4008_cpu_suspend, pnx4008_cpu_suspend_sz);
+
+	/*do suspend */
+	pnx4008_cpu_suspend_ptr = (void *)SRAM_VA;
+	pnx4008_cpu_suspend_ptr();
+
+	/*restoring portion of SRAM that was used by suspend function */
+	memcpy((void *)SRAM_VA, saved_sram, pnx4008_cpu_suspend_sz);
+
+	clk_enable(pll4_clk);
+
+	local_fiq_enable();
+	local_irq_enable();
+}
+
+static int pnx4008_pm_enter(suspend_state_t state)
+{
+	switch (state) {
+	case PM_SUSPEND_STANDBY:
+		pnx4008_standby();
+		break;
+	case PM_SUSPEND_MEM:
+		pnx4008_suspend();
+		break;
+	case PM_SUSPEND_DISK:
+		return -ENOTSUPP;
+	default:
+		return -EINVAL;
+	}
+	return 0;
+}
+
+/*
+ * Called after processes are frozen, but before we shut down devices.
+ */
+static int pnx4008_pm_prepare(suspend_state_t state)
+{
+	switch (state) {
+	case PM_SUSPEND_STANDBY:
+	case PM_SUSPEND_MEM:
+		break;
+
+	case PM_SUSPEND_DISK:
+		return -ENOTSUPP;
+		break;
+
+	default:
+		return -EINVAL;
+		break;
+	}
+	return 0;
+}
+
+/*
+ * Called after devices are re-setup, but before processes are thawed.
+ */
+static int pnx4008_pm_finish(suspend_state_t state)
+{
+	return 0;
+}
+
+/*
+ * Set to PM_DISK_FIRMWARE so we can quickly veto suspend-to-disk.
+ */
+static struct pm_ops pnx4008_pm_ops = {
+	.prepare = pnx4008_pm_prepare,
+	.enter = pnx4008_pm_enter,
+	.finish = pnx4008_pm_finish,
+};
+
+static int __init pnx4008_pm_init(void)
+{
+	u32 sram_size_to_allocate;
+
+	pll4_clk = clk_get(0, "ck_pll4");
+	if (IS_ERR(pll4_clk)) {
+		printk(KERN_ERR
+		       "PM Suspend cannot acquire ARM(PLL4) clock control\n");
+		return PTR_ERR(pll4_clk);
+	}
+
+	if (pnx4008_cpu_standby_sz > pnx4008_cpu_suspend_sz)
+		sram_size_to_allocate = pnx4008_cpu_standby_sz;
+	else
+		sram_size_to_allocate = pnx4008_cpu_suspend_sz;
+
+	saved_sram = kmalloc(sram_size_to_allocate, GFP_ATOMIC);
+	if (!saved_sram) {
+		printk(KERN_ERR
+		       "PM Suspend: cannot allocate memory to save portion of SRAM\n");
+		clk_put(pll4_clk);
+		return -ENOMEM;
+	}
+
+	pm_set_ops(&pnx4008_pm_ops);
+	return 0;
+}
+
+late_initcall(pnx4008_pm_init);
diff --git a/arch/arm/mach-pnx4008/serial.c b/arch/arm/mach-pnx4008/serial.c
new file mode 100644
index 0000000..2e1e04c
--- /dev/null
+++ b/arch/arm/mach-pnx4008/serial.c
@@ -0,0 +1,69 @@
+/*
+ *  linux/arch/arm/mach-pnx4008/serial.c
+ *
+ *  PNX4008 UART initialization
+ *
+ *  Copyright:	MontaVista Software Inc. (c) 2005
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+
+#include <asm/io.h>
+
+#include <asm/arch/platform.h>
+#include <asm/arch/hardware.h>
+
+#include <linux/serial_core.h>
+#include <linux/serial_reg.h>
+#include <asm/arch/pm.h>
+
+#include <asm/arch/clock.h>
+
+#define UART_3		0
+#define UART_4		1
+#define UART_5		2
+#define UART_6		3
+#define UART_UNKNOWN	(-1)
+
+#define UART3_BASE_VA	IO_ADDRESS(PNX4008_UART3_BASE)
+#define UART4_BASE_VA	IO_ADDRESS(PNX4008_UART4_BASE)
+#define UART5_BASE_VA	IO_ADDRESS(PNX4008_UART5_BASE)
+#define UART6_BASE_VA	IO_ADDRESS(PNX4008_UART6_BASE)
+
+#define UART_FCR_OFFSET		8
+#define UART_FIFO_SIZE		64
+
+void pnx4008_uart_init(void)
+{
+	u32 tmp;
+	int i = UART_FIFO_SIZE;
+
+	__raw_writel(0xC1, UART5_BASE_VA + UART_FCR_OFFSET);
+	__raw_writel(0xC1, UART3_BASE_VA + UART_FCR_OFFSET);
+
+	/* Send a NULL to fix the UART HW bug */
+	__raw_writel(0x00, UART5_BASE_VA);
+	__raw_writel(0x00, UART3_BASE_VA);
+
+	while (i--) {
+		tmp = __raw_readl(UART5_BASE_VA);
+		tmp = __raw_readl(UART3_BASE_VA);
+	}
+	__raw_writel(0, UART5_BASE_VA + UART_FCR_OFFSET);
+	__raw_writel(0, UART3_BASE_VA + UART_FCR_OFFSET);
+
+	/* setup wakeup interrupt */
+	start_int_set_rising_edge(SE_U3_RX_INT);
+	start_int_ack(SE_U3_RX_INT);
+	start_int_umask(SE_U3_RX_INT);
+
+	start_int_set_rising_edge(SE_U5_RX_INT);
+	start_int_ack(SE_U5_RX_INT);
+	start_int_umask(SE_U5_RX_INT);
+}
+
diff --git a/arch/arm/mach-pnx4008/sleep.S b/arch/arm/mach-pnx4008/sleep.S
new file mode 100644
index 0000000..93c802b
--- /dev/null
+++ b/arch/arm/mach-pnx4008/sleep.S
@@ -0,0 +1,196 @@
+/*
+ * linux/arch/arm/mach-pnx4008/sleep.S
+ *
+ * PNX4008 support for STOP mode and SDRAM self-refresh
+ *
+ * Authors: Dmitry Chigirev, Vitaly Wool <source@mvista.com>
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#include <linux/config.h>
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <asm/hardware.h>
+
+#define PWRMAN_VA_BASE IO_ADDRESS(PNX4008_PWRMAN_BASE)
+#define PWR_CTRL_REG_OFFS 0x44
+
+#define SDRAM_CFG_VA_BASE IO_ADDRESS(PNX4008_SDRAM_CFG_BASE)
+#define MPMC_STATUS_REG_OFFS 0x4
+
+		.text
+
+ENTRY(pnx4008_cpu_suspend)
+	@this function should be entered in Direct run mode.
+
+	@ save registers on stack
+	stmfd	sp!, {r0 - r6, lr}
+
+	@ setup Power Manager base address in r4
+	@ and put it's value in r5
+	mov	r4, #(PWRMAN_VA_BASE & 0xff000000)
+	orr	r4, r4, #(PWRMAN_VA_BASE & 0x00ff0000)
+	orr	r4, r4, #(PWRMAN_VA_BASE & 0x0000ff00)
+	orr	r4, r4, #(PWRMAN_VA_BASE & 0x000000ff)
+	ldr	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ setup SDRAM controller base address in r2
+	@ and put it's value in r3
+	mov	r2, #(SDRAM_CFG_VA_BASE & 0xff000000)
+	orr	r2, r2, #(SDRAM_CFG_VA_BASE & 0x00ff0000)
+	orr	r2, r2, #(SDRAM_CFG_VA_BASE & 0x0000ff00)
+	orr	r2, r2, #(SDRAM_CFG_VA_BASE & 0x000000ff)
+	ldr	r3, [r2, #MPMC_STATUS_REG_OFFS] @extra read - HW bug workaround
+
+	@ clear SDRAM self-refresh bit latch
+	and	r5, r5, #(~(1 << 8))
+	@ clear SDRAM self-refresh bit
+	and	r5, r5, #(~(1 << 9))
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ do save current bit settings in r1
+	mov	r1, r5
+
+	@ set SDRAM self-refresh bit
+	orr	r5, r5, #(1 << 9)
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ set SDRAM self-refresh bit latch
+	orr	r5, r5, #(1 << 8)
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ clear SDRAM self-refresh bit latch
+	and	r5, r5, #(~(1 << 8))
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ clear SDRAM self-refresh bit
+	and	r5, r5, #(~(1 << 9))
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ wait for SDRAM to get into self-refresh mode
+2:	ldr	r3, [r2, #MPMC_STATUS_REG_OFFS]
+	tst	r3, #(1 << 2)
+	beq	2b
+
+	@ to prepare SDRAM to get out of self-refresh mode after wakeup
+	orr	r5, r5, #(1 << 7)
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ do enter stop mode
+	orr	r5, r5, #(1 << 0)
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+
+	@ sleeping now...
+
+	@ coming out of STOP mode into Direct Run mode
+	@ clear STOP mode and SDRAM self-refresh bits
+	str	r1, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ wait for SDRAM to get out self-refresh mode
+3:	ldr	r3, [r2, #MPMC_STATUS_REG_OFFS]
+	tst	r3, #5
+	bne	3b
+
+	@ restore regs and return
+	ldmfd   sp!, {r0 - r6, pc}
+
+ENTRY(pnx4008_cpu_suspend_sz)
+	.word	. - pnx4008_cpu_suspend
+
+ENTRY(pnx4008_cpu_standby)
+	@ save registers on stack
+	stmfd	sp!, {r0 - r6, lr}
+
+	@ setup Power Manager base address in r4
+	@ and put it's value in r5
+	mov	r4, #(PWRMAN_VA_BASE & 0xff000000)
+	orr	r4, r4, #(PWRMAN_VA_BASE & 0x00ff0000)
+	orr	r4, r4, #(PWRMAN_VA_BASE & 0x0000ff00)
+	orr	r4, r4, #(PWRMAN_VA_BASE & 0x000000ff)
+	ldr	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ setup SDRAM controller base address in r2
+	@ and put it's value in r3
+	mov	r2, #(SDRAM_CFG_VA_BASE & 0xff000000)
+	orr	r2, r2, #(SDRAM_CFG_VA_BASE & 0x00ff0000)
+	orr	r2, r2, #(SDRAM_CFG_VA_BASE & 0x0000ff00)
+	orr	r2, r2, #(SDRAM_CFG_VA_BASE & 0x000000ff)
+	ldr	r3, [r2, #MPMC_STATUS_REG_OFFS] @extra read - HW bug workaround
+
+	@ clear SDRAM self-refresh bit latch
+	and	r5, r5, #(~(1 << 8))
+	@ clear SDRAM self-refresh bit
+	and	r5, r5, #(~(1 << 9))
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ do save current bit settings in r1
+	mov	r1, r5
+
+	@ set SDRAM self-refresh bit
+	orr	r5, r5, #(1 << 9)
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ set SDRAM self-refresh bit latch
+	orr	r5, r5, #(1 << 8)
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ clear SDRAM self-refresh bit latch
+	and	r5, r5, #(~(1 << 8))
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ clear SDRAM self-refresh bit
+	and	r5, r5, #(~(1 << 9))
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ wait for SDRAM to get into self-refresh mode
+2:	ldr	r3, [r2, #MPMC_STATUS_REG_OFFS]
+	tst	r3, #(1 << 2)
+	beq	2b
+
+	@ set 'get out of self-refresh mode after wakeup' bit
+	orr	r5, r5, #(1 << 7)
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	mcr     p15, 0, r0, c7, c0, 4	@ kinda sleeping now...
+
+	@ set SDRAM self-refresh bit latch
+	orr	r5, r5, #(1 << 8)
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ clear SDRAM self-refresh bit latch
+	and	r5, r5, #(~(1 << 8))
+	str	r5, [r4, #PWR_CTRL_REG_OFFS]
+
+	@ wait for SDRAM to get out self-refresh mode
+3:	ldr	r3, [r2, #MPMC_STATUS_REG_OFFS]
+	tst	r3, #5
+	bne	3b
+
+	@ restore regs and return
+	ldmfd   sp!, {r0 - r6, pc}
+
+ENTRY(pnx4008_cpu_standby_sz)
+	.word	. - pnx4008_cpu_standby
+
+ENTRY(pnx4008_cache_clean_invalidate)
+	stmfd	sp!, {r0 - r6, lr}
+#ifdef CONFIG_CPU_DCACHE_WRITETHROUGH
+	mcr	p15, 0, ip, c7, c6, 0		@ invalidate D cache
+#else
+1:	mrc	p15, 0, r15, c7, c14, 3		@ test,clean,invalidate
+	bne     1b
+#endif
+	ldmfd   sp!, {r0 - r6, pc}
diff --git a/arch/arm/mach-pnx4008/time.c b/arch/arm/mach-pnx4008/time.c
new file mode 100644
index 0000000..4ce6806
--- /dev/null
+++ b/arch/arm/mach-pnx4008/time.c
@@ -0,0 +1,141 @@
+/*
+ * arch/arm/mach-pnx4008/time.c
+ *
+ * PNX4008 Timers
+ *
+ * Authors: Vitaly Wool, Dmitry Chigirev, Grigory Tolstolytkin <source@mvista.com>
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/module.h>
+#include <linux/kallsyms.h>
+
+#include <asm/system.h>
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/leds.h>
+#include <asm/irq.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/time.h>
+
+#include <linux/time.h>
+#include <linux/timex.h>
+#include <asm/errno.h>
+
+/*! Note: all timers are UPCOUNTING */
+
+/*!
+ * Returns number of us since last clock interrupt.  Note that interrupts
+ * will have been disabled by do_gettimeoffset()
+ */
+static unsigned long pnx4008_gettimeoffset(void)
+{
+	u32 ticks_to_match =
+	    __raw_readl(HSTIM_MATCH0) - __raw_readl(HSTIM_COUNTER);
+	u32 elapsed = LATCH - ticks_to_match;
+	return (elapsed * (tick_nsec / 1000)) / LATCH;
+}
+
+/*!
+ * IRQ handler for the timer
+ */
+static irqreturn_t pnx4008_timer_interrupt(int irq, void *dev_id,
+					   struct pt_regs *regs)
+{
+	if (__raw_readl(HSTIM_INT) & MATCH0_INT) {
+
+		write_seqlock(&xtime_lock);
+
+		do {
+			timer_tick(regs);
+
+			/*
+			 * this algorithm takes care of possible delay
+			 * for this interrupt handling longer than a normal
+			 * timer period
+			 */
+			__raw_writel(__raw_readl(HSTIM_MATCH0) + LATCH,
+				     HSTIM_MATCH0);
+			__raw_writel(MATCH0_INT, HSTIM_INT);	/* clear interrupt */
+
+			/*
+			 * The goal is to keep incrementing HSTIM_MATCH0
+			 * register until HSTIM_MATCH0 indicates time after
+			 * what HSTIM_COUNTER indicates.
+			 */
+		} while ((signed)
+			 (__raw_readl(HSTIM_MATCH0) -
+			  __raw_readl(HSTIM_COUNTER)) < 0);
+
+		write_sequnlock(&xtime_lock);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static struct irqaction pnx4008_timer_irq = {
+	.name = "PNX4008 Tick Timer",
+	.flags = SA_INTERRUPT | SA_TIMER,
+	.handler = pnx4008_timer_interrupt
+};
+
+/*!
+ * Set up timer and timer interrupt.
+ */
+static __init void pnx4008_setup_timer(void)
+{
+	__raw_writel(RESET_COUNT, MSTIM_CTRL);
+	while (__raw_readl(MSTIM_COUNTER)) ;	/* wait for reset to complete. 100% guarantee event */
+	__raw_writel(0, MSTIM_CTRL);	/* stop the timer */
+	__raw_writel(0, MSTIM_MCTRL);
+
+	__raw_writel(RESET_COUNT, HSTIM_CTRL);
+	while (__raw_readl(HSTIM_COUNTER)) ;	/* wait for reset to complete. 100% guarantee event */
+	__raw_writel(0, HSTIM_CTRL);
+	__raw_writel(0, HSTIM_MCTRL);
+	__raw_writel(0, HSTIM_CCR);
+	__raw_writel(12, HSTIM_PMATCH);	/* scale down to 1 MHZ */
+	__raw_writel(LATCH, HSTIM_MATCH0);
+	__raw_writel(MR0_INT, HSTIM_MCTRL);
+
+	setup_irq(HSTIMER_INT, &pnx4008_timer_irq);
+
+	__raw_writel(COUNT_ENAB | DEBUG_EN, HSTIM_CTRL);	/*start timer, stop when JTAG active */
+}
+
+/* Timer Clock Control in PM register */
+#define TIMCLK_CTRL_REG  IO_ADDRESS((PNX4008_PWRMAN_BASE + 0xBC))
+#define WATCHDOG_CLK_EN                   1
+#define TIMER_CLK_EN                      2	/* HS and MS timers? */
+
+static u32 timclk_ctrl_reg_save;
+
+void pnx4008_timer_suspend(void)
+{
+	timclk_ctrl_reg_save = __raw_readl(TIMCLK_CTRL_REG);
+	__raw_writel(0, TIMCLK_CTRL_REG);	/* disable timers */
+}
+
+void pnx4008_timer_resume(void)
+{
+	__raw_writel(timclk_ctrl_reg_save, TIMCLK_CTRL_REG);	/* enable timers */
+}
+
+struct sys_timer pnx4008_timer = {
+	.init = pnx4008_setup_timer,
+	.offset = pnx4008_gettimeoffset,
+	.suspend = pnx4008_timer_suspend,
+	.resume = pnx4008_timer_resume,
+};
+
diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c
index 3e26d7c..1ab26c6 100644
--- a/arch/arm/mach-pxa/lubbock.c
+++ b/arch/arm/mach-pxa/lubbock.c
@@ -22,6 +22,10 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <asm/arch/pxa2xx_spi.h>
+
 #include <asm/setup.h>
 #include <asm/memory.h>
 #include <asm/mach-types.h>
@@ -196,6 +200,78 @@
 	},
 };
 
+/* ADS7846 is connected through SSP ... and if your board has J5 populated,
+ * you can select it to replace the ucb1400 by switching the touchscreen cable
+ * (to J5) and poking board registers (as done below).  Else it's only useful
+ * for the temperature sensors.
+ */
+static struct resource pxa_ssp_resources[] = {
+	[0] = {
+		.start	= __PREG(SSCR0_P(1)),
+		.end	= __PREG(SSCR0_P(1)) + 0x14,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= IRQ_SSP,
+		.end	= IRQ_SSP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct pxa2xx_spi_master pxa_ssp_master_info = {
+	.ssp_type	= PXA25x_SSP,
+	.clock_enable	= CKEN3_SSP,
+	.num_chipselect	= 0,
+};
+
+static struct platform_device pxa_ssp = {
+	.name		= "pxa2xx-spi",
+	.id		= 1,
+	.resource	= pxa_ssp_resources,
+	.num_resources	= ARRAY_SIZE(pxa_ssp_resources),
+	.dev = {
+		.platform_data	= &pxa_ssp_master_info,
+	},
+};
+
+static int lubbock_ads7846_pendown_state(void)
+{
+	/* TS_BUSY is bit 8 in LUB_MISC_RD, but pendown is irq-only */
+	return 0;
+}
+
+static struct ads7846_platform_data ads_info = {
+	.model			= 7846,
+	.vref_delay_usecs	= 100,		/* internal, no cap */
+	.get_pendown_state	= lubbock_ads7846_pendown_state,
+	// .x_plate_ohms		= 500,	/* GUESS! */
+	// .y_plate_ohms		= 500,	/* GUESS! */
+};
+
+static void ads7846_cs(u32 command)
+{
+	static const unsigned	TS_nCS = 1 << 11;
+	lubbock_set_misc_wr(TS_nCS, (command == PXA2XX_CS_ASSERT) ? 0 : TS_nCS);
+}
+
+static struct pxa2xx_spi_chip ads_hw = {
+	.tx_threshold		= 1,
+	.rx_threshold		= 2,
+	.cs_control		= ads7846_cs,
+};
+
+static struct spi_board_info spi_board_info[] __initdata = { {
+	.modalias	= "ads7846",
+	.platform_data	= &ads_info,
+	.controller_data = &ads_hw,
+	.irq		= LUBBOCK_BB_IRQ,
+	.max_speed_hz	= 120000 /* max sample rate at 3V */
+				* 26 /* command + data + overhead */,
+	.bus_num	= 1,
+	.chip_select	= 0,
+},
+};
+
 static struct platform_device smc91x_device = {
 	.name		= "smc91x",
 	.id		= -1,
@@ -272,6 +348,7 @@
 	&smc91x_device,
 	&lubbock_flash_device[0],
 	&lubbock_flash_device[1],
+	&pxa_ssp,
 };
 
 static struct pxafb_mach_info sharp_lm8v31 __initdata = {
@@ -400,6 +477,8 @@
 	lubbock_flash_data[flashboot^1].name = "application-flash";
 	lubbock_flash_data[flashboot].name = "boot-rom";
 	(void) platform_add_devices(devices, ARRAY_SIZE(devices));
+
+	spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
 }
 
 static struct map_desc lubbock_io_desc[] __initdata = {
@@ -416,6 +495,11 @@
 	pxa_map_io();
 	iotable_init(lubbock_io_desc, ARRAY_SIZE(lubbock_io_desc));
 
+	/* SSP data pins */
+	pxa_gpio_mode(GPIO23_SCLK_MD);
+	pxa_gpio_mode(GPIO25_STXD_MD);
+	pxa_gpio_mode(GPIO26_SRXD_MD);
+
 	/* This enables the BTUART */
 	pxa_gpio_mode(GPIO42_BTRXD_MD);
 	pxa_gpio_mode(GPIO43_BTTXD_MD);
diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig
index 970f98d..0c33413 100644
--- a/arch/arm/mach-s3c2410/Kconfig
+++ b/arch/arm/mach-s3c2410/Kconfig
@@ -70,6 +70,18 @@
 	help
 	  Say Y here if you are using the SMDK2440.
 
+config SMDK2440_CPU2440
+	bool "SMDK2440 with S3C2440 cpu module"
+	depends on ARCH_S3C2440
+	default y if ARCH_S3C2440
+	select CPU_S3C2440
+
+config SMDK2440_CPU2442
+	bool "SMDM2440 with S3C2442 cpu module"
+	depends on ARCH_S3C2440
+	select CPU_S3C2442
+
+
 config MACH_VR1000
 	bool "Thorcom VR1000"
 	select CPU_S3C2410
@@ -109,12 +121,26 @@
 	  Support for S3C2410 and S3C2410A family from the S3C24XX line
 	  of Samsung Mobile CPUs.
 
+config CPU_S3C244X
+	bool
+	depends on ARCH_S3C2410 && (CPU_S3C2440 || CPU_S3C2442)
+	help
+	  Support for S3C2440 and S3C2442 Samsung Mobile CPU based systems.
+
 config CPU_S3C2440
 	bool
 	depends on ARCH_S3C2410
+	select CPU_S3C244X
 	help
 	  Support for S3C2440 Samsung Mobile CPU based systems.
 
+config CPU_S3C2442
+	bool
+	depends on ARCH_S3C2420
+	select CPU_S3C244X
+	help
+	  Support for S3C2442 Samsung Mobile CPU based systems.
+
 comment "S3C2410 Boot"
 
 config S3C2410_BOOT_WATCHDOG
diff --git a/arch/arm/mach-s3c2410/Makefile b/arch/arm/mach-s3c2410/Makefile
index 3e5712d..5e09355 100644
--- a/arch/arm/mach-s3c2410/Makefile
+++ b/arch/arm/mach-s3c2410/Makefile
@@ -24,6 +24,11 @@
 obj-$(CONFIG_PM)	   += pm.o sleep.o
 obj-$(CONFIG_PM_SIMTEC)	   += pm-simtec.o
 
+# S3C244X support
+
+obj-$(CONFIG_CPU_S3C244X)  += s3c244x.o
+obj-$(CONFIG_CPU_S3C244X)  += s3c244x-irq.o
+
 # S3C2440 support
 
 obj-$(CONFIG_CPU_S3C2440)  += s3c2440.o s3c2440-dsc.o
@@ -31,6 +36,11 @@
 obj-$(CONFIG_CPU_S3C2440)  += s3c2440-clock.o
 obj-$(CONFIG_CPU_S3C2440)  += s3c2410-gpio.o
 
+# S3C2442 support
+
+obj-$(CONFIG_CPU_S3C2442)  += s3c2442.o
+obj-$(CONFIG_CPU_S3C2442)  += s3c2442-clock.o
+
 # bast extras
 
 obj-$(CONFIG_BAST_PC104_IRQ)	+= bast-irq.o
diff --git a/arch/arm/mach-s3c2410/clock.c b/arch/arm/mach-s3c2410/clock.c
index 6de713a..99d1746 100644
--- a/arch/arm/mach-s3c2410/clock.c
+++ b/arch/arm/mach-s3c2410/clock.c
@@ -70,7 +70,7 @@
 		clkcon &= ~clocks;
 
 	/* ensure none of the special function bits set */
-	clkcon &= ~(S3C2410_CLKCON_IDLE|S3C2410_CLKCON_POWER);
+	clkcon &= ~(S3C2410_CLKCON_IDLE|S3C2410_CLKCON_POWER | 3);
 
 	__raw_writel(clkcon, S3C2410_CLKCON);
 }
diff --git a/arch/arm/mach-s3c2410/common-smdk.c b/arch/arm/mach-s3c2410/common-smdk.c
index c940890..a40eaa6 100644
--- a/arch/arm/mach-s3c2410/common-smdk.c
+++ b/arch/arm/mach-s3c2410/common-smdk.c
@@ -34,6 +34,7 @@
 #include <asm/irq.h>
 
 #include <asm/arch/regs-gpio.h>
+#include <asm/arch/leds-gpio.h>
 
 #include <asm/arch/nand.h>
 
@@ -41,6 +42,66 @@
 #include "devs.h"
 #include "pm.h"
 
+/* LED devices */
+
+static struct s3c24xx_led_platdata smdk_pdata_led4 = {
+	.gpio		= S3C2410_GPF4,
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.name		= "led4",
+	.def_trigger	= "timer",
+};
+
+static struct s3c24xx_led_platdata smdk_pdata_led5 = {
+	.gpio		= S3C2410_GPF5,
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.name		= "led5",
+	.def_trigger	= "nand-disk",
+};
+
+static struct s3c24xx_led_platdata smdk_pdata_led6 = {
+	.gpio		= S3C2410_GPF6,
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.name		= "led6",
+};
+
+static struct s3c24xx_led_platdata smdk_pdata_led7 = {
+	.gpio		= S3C2410_GPF7,
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.name		= "led7",
+};
+
+static struct platform_device smdk_led4 = {
+	.name		= "s3c24xx_led",
+	.id		= 0,
+	.dev		= {
+		.platform_data = &smdk_pdata_led4,
+	},
+};
+
+static struct platform_device smdk_led5 = {
+	.name		= "s3c24xx_led",
+	.id		= 1,
+	.dev		= {
+		.platform_data = &smdk_pdata_led5,
+	},
+};
+
+static struct platform_device smdk_led6 = {
+	.name		= "s3c24xx_led",
+	.id		= 2,
+	.dev		= {
+		.platform_data = &smdk_pdata_led6,
+	},
+};
+
+static struct platform_device smdk_led7 = {
+	.name		= "s3c24xx_led",
+	.id		= 3,
+	.dev		= {
+		.platform_data = &smdk_pdata_led7,
+	},
+};
+
 /* NAND parititon from 2.4.18-swl5 */
 
 static struct mtd_partition smdk_default_nand_part[] = {
@@ -111,6 +172,10 @@
 
 static struct platform_device __initdata *smdk_devs[] = {
 	&s3c_device_nand,
+	&smdk_led4,
+	&smdk_led5,
+	&smdk_led6,
+	&smdk_led7,
 };
 
 void __init smdk_machine_init(void)
diff --git a/arch/arm/mach-s3c2410/cpu.c b/arch/arm/mach-s3c2410/cpu.c
index 70c34fc..52842e6 100644
--- a/arch/arm/mach-s3c2410/cpu.c
+++ b/arch/arm/mach-s3c2410/cpu.c
@@ -37,12 +37,16 @@
 #include <asm/mach/map.h>
 
 #include <asm/arch/regs-gpio.h>
+#include <asm/arch/regs-serial.h>
 
 #include "cpu.h"
+#include "devs.h"
 #include "clock.h"
 #include "s3c2400.h"
 #include "s3c2410.h"
+#include "s3c244x.h"
 #include "s3c2440.h"
+#include "s3c2442.h"
 
 struct cpu_table {
 	unsigned long	idcode;
@@ -59,6 +63,7 @@
 static const char name_s3c2400[]  = "S3C2400";
 static const char name_s3c2410[]  = "S3C2410";
 static const char name_s3c2440[]  = "S3C2440";
+static const char name_s3c2442[]  = "S3C2442";
 static const char name_s3c2410a[] = "S3C2410A";
 static const char name_s3c2440a[] = "S3C2440A";
 
@@ -84,22 +89,31 @@
 	{
 		.idcode		= 0x32440000,
 		.idmask		= 0xffffffff,
-		.map_io		= s3c2440_map_io,
-		.init_clocks	= s3c2440_init_clocks,
-		.init_uarts	= s3c2440_init_uarts,
+		.map_io		= s3c244x_map_io,
+		.init_clocks	= s3c244x_init_clocks,
+		.init_uarts	= s3c244x_init_uarts,
 		.init		= s3c2440_init,
 		.name		= name_s3c2440
 	},
 	{
 		.idcode		= 0x32440001,
 		.idmask		= 0xffffffff,
-		.map_io		= s3c2440_map_io,
-		.init_clocks	= s3c2440_init_clocks,
-		.init_uarts	= s3c2440_init_uarts,
+		.map_io		= s3c244x_map_io,
+		.init_clocks	= s3c244x_init_clocks,
+		.init_uarts	= s3c244x_init_uarts,
 		.init		= s3c2440_init,
 		.name		= name_s3c2440a
 	},
 	{
+		.idcode		= 0x32440aaa,
+		.idmask		= 0xffffffff,
+		.map_io		= s3c244x_map_io,
+		.init_clocks	= s3c244x_init_clocks,
+		.init_uarts	= s3c244x_init_uarts,
+		.init		= s3c2442_init,
+		.name		= name_s3c2442
+	},
+	{
 		.idcode		= 0x0,   /* S3C2400 doesn't have an idcode */
 		.idmask		= 0xffffffff,
 		.map_io		= s3c2400_map_io,
@@ -175,13 +189,13 @@
 		panic("Unknown S3C24XX CPU");
 	}
 
+	printk("CPU %s (id 0x%08lx)\n", cpu->name, idcode);
+
 	if (cpu->map_io == NULL || cpu->init == NULL) {
 		printk(KERN_ERR "CPU %s support not enabled\n", cpu->name);
 		panic("Unsupported S3C24XX CPU");
 	}
 
-	printk("CPU %s (id 0x%08lx)\n", cpu->name, idcode);
-
 	(cpu->map_io)(mach_desc, size);
 }
 
@@ -208,6 +222,49 @@
 		(cpu->init_clocks)(xtal);
 }
 
+/* uart management */
+
+static int nr_uarts __initdata = 0;
+
+static struct s3c2410_uartcfg uart_cfgs[3];
+
+/* s3c24xx_init_uartdevs
+ *
+ * copy the specified platform data and configuration into our central
+ * set of devices, before the data is thrown away after the init process.
+ *
+ * This also fills in the array passed to the serial driver for the
+ * early initialisation of the console.
+*/
+
+void __init s3c24xx_init_uartdevs(char *name,
+				  struct s3c24xx_uart_resources *res,
+				  struct s3c2410_uartcfg *cfg, int no)
+{
+	struct platform_device *platdev;
+	struct s3c2410_uartcfg *cfgptr = uart_cfgs;
+	struct s3c24xx_uart_resources *resp;
+	int uart;
+
+	memcpy(cfgptr, cfg, sizeof(struct s3c2410_uartcfg) * no);
+
+	for (uart = 0; uart < no; uart++, cfg++, cfgptr++) {
+		platdev = s3c24xx_uart_src[cfgptr->hwport];
+
+		resp = res + cfgptr->hwport;
+
+		s3c24xx_uart_devs[uart] = platdev;
+
+		platdev->name = name;
+		platdev->resource = resp->resources;
+		platdev->num_resources = resp->nr_resources;
+
+		platdev->dev.platform_data = cfgptr;
+	}
+
+	nr_uarts = no;
+}
+
 void __init s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no)
 {
 	if (cpu == NULL)
@@ -232,6 +289,10 @@
 	if (ret != 0)
 		return ret;
 
+	ret = platform_add_devices(s3c24xx_uart_devs, nr_uarts);
+	if (ret != 0)
+		return ret;
+
 	if (board != NULL) {
 		struct platform_device **ptr = board->devices;
 		int i;
diff --git a/arch/arm/mach-s3c2410/cpu.h b/arch/arm/mach-s3c2410/cpu.h
index fc10677..4086289 100644
--- a/arch/arm/mach-s3c2410/cpu.h
+++ b/arch/arm/mach-s3c2410/cpu.h
@@ -31,6 +31,8 @@
 #define print_mhz(m) ((m) / MHZ), ((m / 1000) % 1000)
 
 /* forward declaration */
+struct s3c24xx_uart_resources;
+struct platform_device;
 struct s3c2410_uartcfg;
 struct map_desc;
 
@@ -44,6 +46,10 @@
 
 extern void s3c24xx_init_clocks(int xtal);
 
+extern void s3c24xx_init_uartdevs(char *name,
+				  struct s3c24xx_uart_resources *res,
+				  struct s3c2410_uartcfg *cfg, int no);
+
 /* the board structure is used at first initialsation time
  * to get info such as the devices to register for this
  * board. This is done because platfrom_add_devices() cannot
@@ -68,3 +74,4 @@
 /* system device classes */
 
 extern struct sysdev_class s3c2440_sysclass;
+extern struct sysdev_class s3c2442_sysclass;
diff --git a/arch/arm/mach-s3c2410/devs.c b/arch/arm/mach-s3c2410/devs.c
index ca09ba5..ad3845e 100644
--- a/arch/arm/mach-s3c2410/devs.c
+++ b/arch/arm/mach-s3c2410/devs.c
@@ -38,10 +38,86 @@
 #include <asm/arch/regs-serial.h>
 
 #include "devs.h"
+#include "cpu.h"
 
 /* Serial port registrations */
 
-struct platform_device *s3c24xx_uart_devs[3];
+static struct resource s3c2410_uart0_resource[] = {
+	[0] = {
+		.start = S3C2410_PA_UART0,
+		.end   = S3C2410_PA_UART0 + 0x3fff,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_S3CUART_RX0,
+		.end   = IRQ_S3CUART_ERR0,
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+static struct resource s3c2410_uart1_resource[] = {
+	[0] = {
+		.start = S3C2410_PA_UART1,
+		.end   = S3C2410_PA_UART1 + 0x3fff,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_S3CUART_RX1,
+		.end   = IRQ_S3CUART_ERR1,
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+static struct resource s3c2410_uart2_resource[] = {
+	[0] = {
+		.start = S3C2410_PA_UART2,
+		.end   = S3C2410_PA_UART2 + 0x3fff,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_S3CUART_RX2,
+		.end   = IRQ_S3CUART_ERR2,
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+struct s3c24xx_uart_resources s3c2410_uart_resources[] __initdata = {
+	[0] = {
+		.resources	= s3c2410_uart0_resource,
+		.nr_resources	= ARRAY_SIZE(s3c2410_uart0_resource),
+	},
+	[1] = {
+		.resources	= s3c2410_uart1_resource,
+		.nr_resources	= ARRAY_SIZE(s3c2410_uart1_resource),
+	},
+	[2] = {
+		.resources	= s3c2410_uart2_resource,
+		.nr_resources	= ARRAY_SIZE(s3c2410_uart2_resource),
+	},
+};
+
+/* yart devices */
+
+static struct platform_device s3c24xx_uart_device0 = {
+	.id		= 0,
+};
+
+static struct platform_device s3c24xx_uart_device1 = {
+	.id		= 1,
+};
+
+static struct platform_device s3c24xx_uart_device2 = {
+	.id		= 2,
+};
+
+struct platform_device *s3c24xx_uart_src[3] = {
+	&s3c24xx_uart_device0,
+	&s3c24xx_uart_device1,
+	&s3c24xx_uart_device2,
+};
+
+struct platform_device *s3c24xx_uart_devs[3] = {
+};
 
 /* USB Host Controller */
 
diff --git a/arch/arm/mach-s3c2410/devs.h b/arch/arm/mach-s3c2410/devs.h
index 52c4bab..fa124ed 100644
--- a/arch/arm/mach-s3c2410/devs.h
+++ b/arch/arm/mach-s3c2410/devs.h
@@ -17,7 +17,15 @@
 #include <linux/config.h>
 #include <linux/platform_device.h>
 
+struct s3c24xx_uart_resources {
+	struct resource		*resources;
+	unsigned long		 nr_resources;
+};
+
+extern struct s3c24xx_uart_resources s3c2410_uart_resources[];
+
 extern struct platform_device *s3c24xx_uart_devs[];
+extern struct platform_device *s3c24xx_uart_src[];
 
 extern struct platform_device s3c_device_usb;
 extern struct platform_device s3c_device_lcd;
diff --git a/arch/arm/mach-s3c2410/mach-anubis.c b/arch/arm/mach-s3c2410/mach-anubis.c
index cc97fbf..52bf718 100644
--- a/arch/arm/mach-s3c2410/mach-anubis.c
+++ b/arch/arm/mach-s3c2410/mach-anubis.c
@@ -131,7 +131,7 @@
 };
 
 
-static struct s3c2410_uartcfg anubis_uartcfgs[] = {
+static struct s3c2410_uartcfg anubis_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
 		.flags	     = 0,
diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c
index 995bb8a..947234d 100644
--- a/arch/arm/mach-s3c2410/mach-bast.c
+++ b/arch/arm/mach-s3c2410/mach-bast.c
@@ -208,7 +208,7 @@
 };
 
 
-static struct s3c2410_uartcfg bast_uartcfgs[] = {
+static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
 		.flags	     = 0,
diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c
index 646a3a5..aec431b 100644
--- a/arch/arm/mach-s3c2410/mach-h1940.c
+++ b/arch/arm/mach-s3c2410/mach-h1940.c
@@ -72,7 +72,7 @@
 #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
 #define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
 
-static struct s3c2410_uartcfg h1940_uartcfgs[] = {
+static struct s3c2410_uartcfg h1940_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
 		.flags	     = 0,
diff --git a/arch/arm/mach-s3c2410/mach-nexcoder.c b/arch/arm/mach-s3c2410/mach-nexcoder.c
index 07d0950..065a1d4 100644
--- a/arch/arm/mach-s3c2410/mach-nexcoder.c
+++ b/arch/arm/mach-s3c2410/mach-nexcoder.c
@@ -51,7 +51,7 @@
 #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
 #define UFCON S3C2410_UFCON_RXTRIG12 | S3C2410_UFCON_FIFOMODE
 
-static struct s3c2410_uartcfg nexcoder_uartcfgs[] = {
+static struct s3c2410_uartcfg nexcoder_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
 		.flags	     = 0,
diff --git a/arch/arm/mach-s3c2410/mach-osiris.c b/arch/arm/mach-s3c2410/mach-osiris.c
index ae07875..858fd03 100644
--- a/arch/arm/mach-s3c2410/mach-osiris.c
+++ b/arch/arm/mach-s3c2410/mach-osiris.c
@@ -95,8 +95,7 @@
 	}
 };
 
-
-static struct s3c2410_uartcfg osiris_uartcfgs[] = {
+static struct s3c2410_uartcfg osiris_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
 		.flags	     = 0,
@@ -107,7 +106,7 @@
 		.clocks_size = ARRAY_SIZE(osiris_serial_clocks)
 	},
 	[1] = {
-		.hwport	     = 2,
+		.hwport	     = 1,
 		.flags	     = 0,
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
diff --git a/arch/arm/mach-s3c2410/mach-otom.c b/arch/arm/mach-s3c2410/mach-otom.c
index b39daed..c71673f 100644
--- a/arch/arm/mach-s3c2410/mach-otom.c
+++ b/arch/arm/mach-s3c2410/mach-otom.c
@@ -45,7 +45,7 @@
 #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
 #define UFCON S3C2410_UFCON_RXTRIG12 | S3C2410_UFCON_FIFOMODE
 
-static struct s3c2410_uartcfg otom11_uartcfgs[] = {
+static struct s3c2410_uartcfg otom11_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
 		.flags	     = 0,
diff --git a/arch/arm/mach-s3c2410/mach-smdk2410.c b/arch/arm/mach-s3c2410/mach-smdk2410.c
index 2db932d..25f7e9f 100644
--- a/arch/arm/mach-s3c2410/mach-smdk2410.c
+++ b/arch/arm/mach-s3c2410/mach-smdk2410.c
@@ -65,7 +65,7 @@
 #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
 #define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
 
-static struct s3c2410_uartcfg smdk2410_uartcfgs[] = {
+static struct s3c2410_uartcfg smdk2410_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
 		.flags	     = 0,
diff --git a/arch/arm/mach-s3c2410/mach-smdk2440.c b/arch/arm/mach-s3c2410/mach-smdk2440.c
index 5fffd1d..d661c6b 100644
--- a/arch/arm/mach-s3c2410/mach-smdk2440.c
+++ b/arch/arm/mach-s3c2410/mach-smdk2440.c
@@ -86,7 +86,7 @@
 #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
 #define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
 
-static struct s3c2410_uartcfg smdk2440_uartcfgs[] = {
+static struct s3c2410_uartcfg smdk2440_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
 		.flags	     = 0,
diff --git a/arch/arm/mach-s3c2410/mach-vr1000.c b/arch/arm/mach-s3c2410/mach-vr1000.c
index 785fc9c..d18efb2 100644
--- a/arch/arm/mach-s3c2410/mach-vr1000.c
+++ b/arch/arm/mach-s3c2410/mach-vr1000.c
@@ -166,7 +166,7 @@
 	}
 };
 
-static struct s3c2410_uartcfg vr1000_uartcfgs[] = {
+static struct s3c2410_uartcfg vr1000_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
 		.flags	     = 0,
diff --git a/arch/arm/mach-s3c2410/pm.c b/arch/arm/mach-s3c2410/pm.c
index fe57d96..43e9a55 100644
--- a/arch/arm/mach-s3c2410/pm.c
+++ b/arch/arm/mach-s3c2410/pm.c
@@ -58,7 +58,11 @@
 
 /* cache functions from arch/arm/mm/proc-arm920.S */
 
+#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH
 extern void arm920_flush_kern_cache_all(void);
+#else
+static void arm920_flush_kern_cache_all(void) { }
+#endif
 
 #define PFX "s3c24xx-pm: "
 
diff --git a/arch/arm/mach-s3c2410/s3c2410.c b/arch/arm/mach-s3c2410/s3c2410.c
index 0a2013a..0852e87 100644
--- a/arch/arm/mach-s3c2410/s3c2410.c
+++ b/arch/arm/mach-s3c2410/s3c2410.c
@@ -42,6 +42,7 @@
 
 #include "s3c2410.h"
 #include "cpu.h"
+#include "devs.h"
 #include "clock.h"
 
 /* Initial IO mappings */
@@ -55,93 +56,13 @@
 	IODESC_ENT(WATCHDOG),
 };
 
-static struct resource s3c_uart0_resource[] = {
-	[0] = {
-		.start = S3C2410_PA_UART0,
-		.end   = S3C2410_PA_UART0 + 0x3fff,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = IRQ_S3CUART_RX0,
-		.end   = IRQ_S3CUART_ERR0,
-		.flags = IORESOURCE_IRQ,
-	}
-
-};
-
-static struct resource s3c_uart1_resource[] = {
-	[0] = {
-		.start = S3C2410_PA_UART1,
-		.end   = S3C2410_PA_UART1 + 0x3fff,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = IRQ_S3CUART_RX1,
-		.end   = IRQ_S3CUART_ERR1,
-		.flags = IORESOURCE_IRQ,
-	}
-};
-
-static struct resource s3c_uart2_resource[] = {
-	[0] = {
-		.start = S3C2410_PA_UART2,
-		.end   = S3C2410_PA_UART2 + 0x3fff,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = IRQ_S3CUART_RX2,
-		.end   = IRQ_S3CUART_ERR2,
-		.flags = IORESOURCE_IRQ,
-	}
-};
-
 /* our uart devices */
 
-static struct platform_device s3c_uart0 = {
-	.name		  = "s3c2410-uart",
-	.id		  = 0,
-	.num_resources	  = ARRAY_SIZE(s3c_uart0_resource),
-	.resource	  = s3c_uart0_resource,
-};
-
-
-static struct platform_device s3c_uart1 = {
-	.name		  = "s3c2410-uart",
-	.id		  = 1,
-	.num_resources	  = ARRAY_SIZE(s3c_uart1_resource),
-	.resource	  = s3c_uart1_resource,
-};
-
-static struct platform_device s3c_uart2 = {
-	.name		  = "s3c2410-uart",
-	.id		  = 2,
-	.num_resources	  = ARRAY_SIZE(s3c_uart2_resource),
-	.resource	  = s3c_uart2_resource,
-};
-
-static struct platform_device *uart_devices[] __initdata = {
-	&s3c_uart0,
-	&s3c_uart1,
-	&s3c_uart2
-};
-
-static int s3c2410_uart_count = 0;
-
 /* uart registration process */
 
 void __init s3c2410_init_uarts(struct s3c2410_uartcfg *cfg, int no)
 {
-	struct platform_device *platdev;
-	int uart;
-
-	for (uart = 0; uart < no; uart++, cfg++) {
-		platdev = uart_devices[cfg->hwport];
-
-		s3c24xx_uart_devs[uart] = platdev;
-		platdev->dev.platform_data = cfg;
-	}
-
-	s3c2410_uart_count = uart;
+	s3c24xx_init_uartdevs("s3c2410-uart", s3c2410_uart_resources, cfg, no);
 }
 
 /* s3c2410_map_io
@@ -193,5 +114,5 @@
 {
 	printk("S3C2410: Initialising architecture\n");
 
-	return platform_add_devices(s3c24xx_uart_devs, s3c2410_uart_count);
+	return 0;
 }
diff --git a/arch/arm/mach-s3c2410/s3c2440-irq.c b/arch/arm/mach-s3c2410/s3c2440-irq.c
index 278d004..acfe387 100644
--- a/arch/arm/mach-s3c2410/s3c2440-irq.c
+++ b/arch/arm/mach-s3c2410/s3c2440-irq.c
@@ -100,73 +100,12 @@
 	.ack	    = s3c_irq_wdtac97_ack,
 };
 
-/* camera irq */
-
-static void s3c_irq_demux_cam(unsigned int irq,
-			      struct irqdesc *desc,
-			      struct pt_regs *regs)
-{
-	unsigned int subsrc, submsk;
-	struct irqdesc *mydesc;
-
-	/* read the current pending interrupts, and the mask
-	 * for what it is available */
-
-	subsrc = __raw_readl(S3C2410_SUBSRCPND);
-	submsk = __raw_readl(S3C2410_INTSUBMSK);
-
-	subsrc &= ~submsk;
-	subsrc >>= 11;
-	subsrc &= 3;
-
-	if (subsrc != 0) {
-		if (subsrc & 1) {
-			mydesc = irq_desc + IRQ_S3C2440_CAM_C;
-			desc_handle_irq(IRQ_S3C2440_CAM_C, mydesc, regs);
-		}
-		if (subsrc & 2) {
-			mydesc = irq_desc + IRQ_S3C2440_CAM_P;
-			desc_handle_irq(IRQ_S3C2440_CAM_P, mydesc, regs);
-		}
-	}
-}
-
-#define INTMSK_CAM (1UL << (IRQ_CAM - IRQ_EINT0))
-
-static void
-s3c_irq_cam_mask(unsigned int irqno)
-{
-	s3c_irqsub_mask(irqno, INTMSK_CAM, 3<<11);
-}
-
-static void
-s3c_irq_cam_unmask(unsigned int irqno)
-{
-	s3c_irqsub_unmask(irqno, INTMSK_CAM);
-}
-
-static void
-s3c_irq_cam_ack(unsigned int irqno)
-{
-	s3c_irqsub_maskack(irqno, INTMSK_CAM, 3<<11);
-}
-
-static struct irqchip s3c_irq_cam = {
-	.mask	    = s3c_irq_cam_mask,
-	.unmask	    = s3c_irq_cam_unmask,
-	.ack	    = s3c_irq_cam_ack,
-};
-
 static int s3c2440_irq_add(struct sys_device *sysdev)
 {
 	unsigned int irqno;
 
 	printk("S3C2440: IRQ Support\n");
 
-	set_irq_chip(IRQ_NFCON, &s3c_irq_level_chip);
-	set_irq_handler(IRQ_NFCON, do_level_IRQ);
-	set_irq_flags(IRQ_NFCON, IRQF_VALID);
-
 	/* add new chained handler for wdt, ac7 */
 
 	set_irq_chip(IRQ_WDT, &s3c_irq_level_chip);
@@ -179,18 +118,6 @@
 		set_irq_flags(irqno, IRQF_VALID);
 	}
 
-	/* add chained handler for camera */
-
-	set_irq_chip(IRQ_CAM, &s3c_irq_level_chip);
-	set_irq_handler(IRQ_CAM, do_level_IRQ);
-	set_irq_chained_handler(IRQ_CAM, s3c_irq_demux_cam);
-
-	for (irqno = IRQ_S3C2440_CAM_C; irqno <= IRQ_S3C2440_CAM_P; irqno++) {
-		set_irq_chip(irqno, &s3c_irq_cam);
-		set_irq_handler(irqno, do_level_IRQ);
-		set_irq_flags(irqno, IRQF_VALID);
-	}
-
 	return 0;
 }
 
@@ -198,10 +125,10 @@
 	.add	= s3c2440_irq_add,
 };
 
-static int s3c24xx_irq_driver(void)
+static int s3c2440_irq_init(void)
 {
 	return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_irq_driver);
 }
 
-arch_initcall(s3c24xx_irq_driver);
+arch_initcall(s3c2440_irq_init);
 
diff --git a/arch/arm/mach-s3c2410/s3c2440.c b/arch/arm/mach-s3c2410/s3c2440.c
index b7fe6d9..0ab50f4 100644
--- a/arch/arm/mach-s3c2410/s3c2440.c
+++ b/arch/arm/mach-s3c2410/s3c2440.c
@@ -1,6 +1,6 @@
 /* linux/arch/arm/mach-s3c2410/s3c2440.c
  *
- * Copyright (c) 2004-2005 Simtec Electronics
+ * Copyright (c) 2004-2006 Simtec Electronics
  *   Ben Dooks <ben@simtec.co.uk>
  *
  * Samsung S3C2440 Mobile CPU support
@@ -8,16 +8,6 @@
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
- *
- * Modifications:
- *	24-Aug-2004 BJD  Start of s3c2440 support
- *	12-Oct-2004 BJD	 Moved clock info out to clock.c
- *	01-Nov-2004 BJD  Fixed clock build code
- *	09-Nov-2004 BJD  Added sysdev for power management
- *	04-Nov-2004 BJD  New serial registration
- *	15-Nov-2004 BJD  Rename the i2c device for the s3c2440
- *	14-Jan-2005 BJD  Moved clock init code into seperate function
- *	14-Jan-2005 BJD  Removed un-used clock bits
 */
 
 #include <linux/kernel.h>
@@ -50,234 +40,20 @@
 #include "cpu.h"
 #include "pm.h"
 
-
-static struct map_desc s3c2440_iodesc[] __initdata = {
-	IODESC_ENT(USBHOST),
-	IODESC_ENT(CLKPWR),
-	IODESC_ENT(LCD),
-	IODESC_ENT(TIMER),
-	IODESC_ENT(ADC),
-	IODESC_ENT(WATCHDOG),
-};
-
-static struct resource s3c_uart0_resource[] = {
-	[0] = {
-		.start = S3C2410_PA_UART0,
-		.end   = S3C2410_PA_UART0 + 0x3fff,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = IRQ_S3CUART_RX0,
-		.end   = IRQ_S3CUART_ERR0,
-		.flags = IORESOURCE_IRQ,
-	}
-
-};
-
-static struct resource s3c_uart1_resource[] = {
-	[0] = {
-		.start = S3C2410_PA_UART1,
-		.end   = S3C2410_PA_UART1 + 0x3fff,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = IRQ_S3CUART_RX1,
-		.end   = IRQ_S3CUART_ERR1,
-		.flags = IORESOURCE_IRQ,
-	}
-};
-
-static struct resource s3c_uart2_resource[] = {
-	[0] = {
-		.start = S3C2410_PA_UART2,
-		.end   = S3C2410_PA_UART2 + 0x3fff,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = IRQ_S3CUART_RX2,
-		.end   = IRQ_S3CUART_ERR2,
-		.flags = IORESOURCE_IRQ,
-	}
-};
-
-/* our uart devices */
-
-static struct platform_device s3c_uart0 = {
-	.name		  = "s3c2440-uart",
-	.id		  = 0,
-	.num_resources	  = ARRAY_SIZE(s3c_uart0_resource),
-	.resource	  = s3c_uart0_resource,
-};
-
-static struct platform_device s3c_uart1 = {
-	.name		  = "s3c2440-uart",
-	.id		  = 1,
-	.num_resources	  = ARRAY_SIZE(s3c_uart1_resource),
-	.resource	  = s3c_uart1_resource,
-};
-
-static struct platform_device s3c_uart2 = {
-	.name		  = "s3c2440-uart",
-	.id		  = 2,
-	.num_resources	  = ARRAY_SIZE(s3c_uart2_resource),
-	.resource	  = s3c_uart2_resource,
-};
-
-static struct platform_device *uart_devices[] __initdata = {
-	&s3c_uart0,
-	&s3c_uart1,
-	&s3c_uart2
-};
-
-/* uart initialisation */
-
-static int __initdata s3c2440_uart_count;
-
-void __init s3c2440_init_uarts(struct s3c2410_uartcfg *cfg, int no)
-{
-	struct platform_device *platdev;
-	int uart;
-
-	for (uart = 0; uart < no; uart++, cfg++) {
-		platdev = uart_devices[cfg->hwport];
-
-		s3c24xx_uart_devs[uart] = platdev;
-		platdev->dev.platform_data = cfg;
-	}
-
-	s3c2440_uart_count = uart;
-}
-
-
-#ifdef CONFIG_PM
-
-static struct sleep_save s3c2440_sleep[] = {
-	SAVE_ITEM(S3C2440_DSC0),
-	SAVE_ITEM(S3C2440_DSC1),
-	SAVE_ITEM(S3C2440_GPJDAT),
-	SAVE_ITEM(S3C2440_GPJCON),
-	SAVE_ITEM(S3C2440_GPJUP)
-};
-
-static int s3c2440_suspend(struct sys_device *dev, pm_message_t state)
-{
-	s3c2410_pm_do_save(s3c2440_sleep, ARRAY_SIZE(s3c2440_sleep));
-	return 0;
-}
-
-static int s3c2440_resume(struct sys_device *dev)
-{
-	s3c2410_pm_do_restore(s3c2440_sleep, ARRAY_SIZE(s3c2440_sleep));
-	return 0;
-}
-
-#else
-#define s3c2440_suspend NULL
-#define s3c2440_resume  NULL
-#endif
-
-struct sysdev_class s3c2440_sysclass = {
-	set_kset_name("s3c2440-core"),
-	.suspend	= s3c2440_suspend,
-	.resume		= s3c2440_resume
-};
-
 static struct sys_device s3c2440_sysdev = {
 	.cls		= &s3c2440_sysclass,
 };
 
-void __init s3c2440_map_io(struct map_desc *mach_desc, int size)
+int __init s3c2440_init(void)
 {
-	/* register our io-tables */
-
-	iotable_init(s3c2440_iodesc, ARRAY_SIZE(s3c2440_iodesc));
-	iotable_init(mach_desc, size);
-
-	/* rename any peripherals used differing from the s3c2410 */
-
-	s3c_device_i2c.name  = "s3c2440-i2c";
-	s3c_device_nand.name = "s3c2440-nand";
+	printk("S3C2440: Initialising architecture\n");
 
 	/* change irq for watchdog */
 
 	s3c_device_wdt.resource[1].start = IRQ_S3C2440_WDT;
 	s3c_device_wdt.resource[1].end   = IRQ_S3C2440_WDT;
-}
 
-void __init s3c2440_init_clocks(int xtal)
-{
-	unsigned long clkdiv;
-	unsigned long camdiv;
-	unsigned long hclk, fclk, pclk;
-	int hdiv = 1;
+	/* register our system device for everything else */
 
-	/* now we've got our machine bits initialised, work out what
-	 * clocks we've got */
-
-	fclk = s3c2410_get_pll(__raw_readl(S3C2410_MPLLCON), xtal) * 2;
-
-	clkdiv = __raw_readl(S3C2410_CLKDIVN);
-	camdiv = __raw_readl(S3C2440_CAMDIVN);
-
-	/* work out clock scalings */
-
-	switch (clkdiv & S3C2440_CLKDIVN_HDIVN_MASK) {
-	case S3C2440_CLKDIVN_HDIVN_1:
-		hdiv = 1;
-		break;
-
-	case S3C2440_CLKDIVN_HDIVN_2:
-		hdiv = 2;
-		break;
-
-	case S3C2440_CLKDIVN_HDIVN_4_8:
-		hdiv = (camdiv & S3C2440_CAMDIVN_HCLK4_HALF) ? 8 : 4;
-		break;
-
-	case S3C2440_CLKDIVN_HDIVN_3_6:
-		hdiv = (camdiv & S3C2440_CAMDIVN_HCLK3_HALF) ? 6 : 3;
-		break;
-	}
-
-	hclk = fclk / hdiv;
-	pclk = hclk / ((clkdiv & S3C2440_CLKDIVN_PDIVN)? 2:1);
-
-	/* print brief summary of clocks, etc */
-
-	printk("S3C2440: core %ld.%03ld MHz, memory %ld.%03ld MHz, peripheral %ld.%03ld MHz\n",
-	       print_mhz(fclk), print_mhz(hclk), print_mhz(pclk));
-
-	/* initialise the clocks here, to allow other things like the
-	 * console to use them, and to add new ones after the initialisation
-	 */
-
-	s3c24xx_setup_clocks(xtal, fclk, hclk, pclk);
-}
-
-/* need to register class before we actually register the device, and
- * we also need to ensure that it has been initialised before any of the
- * drivers even try to use it (even if not on an s3c2440 based system)
- * as a driver which may support both 2410 and 2440 may try and use it.
-*/
-
-static int __init s3c2440_core_init(void)
-{
-	return sysdev_class_register(&s3c2440_sysclass);
-}
-
-core_initcall(s3c2440_core_init);
-
-int __init s3c2440_init(void)
-{
-	int ret;
-
-	printk("S3C2440: Initialising architecture\n");
-
-	ret = sysdev_register(&s3c2440_sysdev);
-	if (ret != 0)
-		printk(KERN_ERR "failed to register sysdev for s3c2440\n");
-	else
-		ret = platform_add_devices(s3c24xx_uart_devs, s3c2440_uart_count);
-
-	return ret;
+	return sysdev_register(&s3c2440_sysdev);
 }
diff --git a/arch/arm/mach-s3c2410/s3c2442-clock.c b/arch/arm/mach-s3c2410/s3c2442-clock.c
new file mode 100644
index 0000000..5b7b301
--- /dev/null
+++ b/arch/arm/mach-s3c2410/s3c2442-clock.c
@@ -0,0 +1,171 @@
+/* linux/arch/arm/mach-s3c2410/s3c2442-clock.c
+ *
+ * Copyright (c) 2004-2005 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2442 Clock support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+*/
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/device.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/mutex.h>
+#include <linux/clk.h>
+
+#include <asm/hardware.h>
+#include <asm/atomic.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+
+#include <asm/arch/regs-clock.h>
+
+#include "clock.h"
+#include "cpu.h"
+
+/* S3C2442 extended clock support */
+
+static unsigned long s3c2442_camif_upll_round(struct clk *clk,
+					      unsigned long rate)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	int div;
+
+	if (rate > parent_rate)
+		return parent_rate;
+
+	div = parent_rate / rate;
+
+	if (div == 3)
+		return parent_rate / 3;
+
+	/* note, we remove the +/- 1 calculations for the divisor */
+
+	div /= 2;
+
+	if (div < 1)
+		div = 1;
+	else if (div > 16)
+		div = 16;
+
+	return parent_rate / (div * 2);
+}
+
+static int s3c2442_camif_upll_setrate(struct clk *clk, unsigned long rate)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long camdivn =  __raw_readl(S3C2440_CAMDIVN);
+
+	rate = s3c2442_camif_upll_round(clk, rate);
+
+	camdivn &= ~S3C2442_CAMDIVN_CAMCLK_DIV3;
+
+	if (rate == parent_rate) {
+		camdivn &= ~S3C2440_CAMDIVN_CAMCLK_SEL;
+	} else if ((parent_rate / rate) == 3) {
+		camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL;
+		camdivn |= S3C2442_CAMDIVN_CAMCLK_DIV3;
+	} else {
+		camdivn &= ~S3C2440_CAMDIVN_CAMCLK_MASK;
+		camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL;
+		camdivn |= (((parent_rate / rate) / 2) - 1);
+	}
+
+	__raw_writel(camdivn, S3C2440_CAMDIVN);
+
+	return 0;
+}
+
+/* Extra S3C2442 clocks */
+
+static struct clk s3c2442_clk_cam = {
+	.name		= "camif",
+	.id		= -1,
+	.enable		= s3c24xx_clkcon_enable,
+	.ctrlbit	= S3C2440_CLKCON_CAMERA,
+};
+
+static struct clk s3c2442_clk_cam_upll = {
+	.name		= "camif-upll",
+	.id		= -1,
+	.set_rate	= s3c2442_camif_upll_setrate,
+	.round_rate	= s3c2442_camif_upll_round,
+};
+
+static int s3c2442_clk_add(struct sys_device *sysdev)
+{
+	unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN);
+	unsigned long clkdivn;
+	struct clk *clk_h;
+	struct clk *clk_p;
+	struct clk *clk_upll;
+
+	printk("S3C2442: Clock Support, DVS %s\n",
+	       (camdivn & S3C2440_CAMDIVN_DVSEN) ? "on" : "off");
+
+	clk_p = clk_get(NULL, "pclk");
+	clk_h = clk_get(NULL, "hclk");
+	clk_upll = clk_get(NULL, "upll");
+
+	if (IS_ERR(clk_p) || IS_ERR(clk_h) || IS_ERR(clk_upll)) {
+		printk(KERN_ERR "S3C2442: Failed to get parent clocks\n");
+		return -EINVAL;
+	}
+
+	/* check rate of UPLL, and if it is near 96MHz, then change
+	 * to using half the UPLL rate for the system */
+
+	if (clk_get_rate(clk_upll) > (94 * MHZ)) {
+		clk_usb_bus.rate = clk_get_rate(clk_upll) / 2;
+
+		mutex_lock(&clocks_mutex);
+
+		clkdivn = __raw_readl(S3C2410_CLKDIVN);
+		clkdivn |= S3C2440_CLKDIVN_UCLK;
+		__raw_writel(clkdivn, S3C2410_CLKDIVN);
+
+		mutex_unlock(&clocks_mutex);
+	}
+
+	s3c2442_clk_cam.parent = clk_h;
+	s3c2442_clk_cam_upll.parent = clk_upll;
+
+	s3c24xx_register_clock(&s3c2442_clk_cam);
+	s3c24xx_register_clock(&s3c2442_clk_cam_upll);
+
+	clk_disable(&s3c2442_clk_cam);
+
+	return 0;
+}
+
+static struct sysdev_driver s3c2442_clk_driver = {
+	.add	= s3c2442_clk_add,
+};
+
+static __init int s3c2442_clk_init(void)
+{
+	return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_clk_driver);
+}
+
+arch_initcall(s3c2442_clk_init);
diff --git a/arch/arm/mach-s3c2410/s3c2442.c b/arch/arm/mach-s3c2410/s3c2442.c
new file mode 100644
index 0000000..debae24
--- /dev/null
+++ b/arch/arm/mach-s3c2410/s3c2442.c
@@ -0,0 +1,52 @@
+/* linux/arch/arm/mach-s3c2410/s3c2440.c
+ *
+ * Copyright (c) 2006 Simtec Electronics
+ *   Ben Dooks <ben@simtec.co.uk>
+ *
+ * Samsung S3C2442 Mobile CPU support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/sysdev.h>
+#include <linux/clk.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+
+#include <asm/arch/regs-clock.h>
+#include <asm/arch/regs-serial.h>
+#include <asm/arch/regs-gpio.h>
+#include <asm/arch/regs-gpioj.h>
+#include <asm/arch/regs-dsc.h>
+
+#include "s3c2442.h"
+#include "clock.h"
+#include "devs.h"
+#include "cpu.h"
+#include "pm.h"
+
+static struct sys_device s3c2442_sysdev = {
+	.cls		= &s3c2442_sysclass,
+};
+
+int __init s3c2442_init(void)
+{
+	printk("S3C2442: Initialising architecture\n");
+
+	return sysdev_register(&s3c2442_sysdev);
+}
diff --git a/arch/arm/mach-s3c2410/s3c2442.h b/arch/arm/mach-s3c2410/s3c2442.h
new file mode 100644
index 0000000..0ae37d2
--- /dev/null
+++ b/arch/arm/mach-s3c2410/s3c2442.h
@@ -0,0 +1,17 @@
+/* arch/arm/mach-s3c2410/s3c2442.h
+ *
+ * Copyright (c) 2006 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * Header file for s3c2442 cpu support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifdef CONFIG_CPU_S3C2442
+extern  int s3c2442_init(void);
+#else
+#define s3c2442_init NULL
+#endif
diff --git a/arch/arm/mach-s3c2410/s3c244x-irq.c b/arch/arm/mach-s3c2410/s3c244x-irq.c
new file mode 100644
index 0000000..2aadca1
--- /dev/null
+++ b/arch/arm/mach-s3c2410/s3c244x-irq.c
@@ -0,0 +1,142 @@
+/* linux/arch/arm/mach-s3c2410/s3c2440-irq.c
+ *
+ * Copyright (c) 2003,2004 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ * Changelog:
+ *	25-Jul-2005 BJD		Split from irq.c
+ *
+*/
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/ptrace.h>
+#include <linux/sysdev.h>
+
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+
+#include <asm/mach/irq.h>
+
+#include <asm/arch/regs-irq.h>
+#include <asm/arch/regs-gpio.h>
+
+#include "cpu.h"
+#include "pm.h"
+#include "irq.h"
+
+/* camera irq */
+
+static void s3c_irq_demux_cam(unsigned int irq,
+			      struct irqdesc *desc,
+			      struct pt_regs *regs)
+{
+	unsigned int subsrc, submsk;
+	struct irqdesc *mydesc;
+
+	/* read the current pending interrupts, and the mask
+	 * for what it is available */
+
+	subsrc = __raw_readl(S3C2410_SUBSRCPND);
+	submsk = __raw_readl(S3C2410_INTSUBMSK);
+
+	subsrc &= ~submsk;
+	subsrc >>= 11;
+	subsrc &= 3;
+
+	if (subsrc != 0) {
+		if (subsrc & 1) {
+			mydesc = irq_desc + IRQ_S3C2440_CAM_C;
+			desc_handle_irq(IRQ_S3C2440_CAM_C, mydesc, regs);
+		}
+		if (subsrc & 2) {
+			mydesc = irq_desc + IRQ_S3C2440_CAM_P;
+			desc_handle_irq(IRQ_S3C2440_CAM_P, mydesc, regs);
+		}
+	}
+}
+
+#define INTMSK_CAM (1UL << (IRQ_CAM - IRQ_EINT0))
+
+static void
+s3c_irq_cam_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_CAM, 3<<11);
+}
+
+static void
+s3c_irq_cam_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_CAM);
+}
+
+static void
+s3c_irq_cam_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_CAM, 3<<11);
+}
+
+static struct irqchip s3c_irq_cam = {
+	.mask	    = s3c_irq_cam_mask,
+	.unmask	    = s3c_irq_cam_unmask,
+	.ack	    = s3c_irq_cam_ack,
+};
+
+static int s3c244x_irq_add(struct sys_device *sysdev)
+{
+	unsigned int irqno;
+
+	set_irq_chip(IRQ_NFCON, &s3c_irq_level_chip);
+	set_irq_handler(IRQ_NFCON, do_level_IRQ);
+	set_irq_flags(IRQ_NFCON, IRQF_VALID);
+
+	/* add chained handler for camera */
+
+	set_irq_chip(IRQ_CAM, &s3c_irq_level_chip);
+	set_irq_handler(IRQ_CAM, do_level_IRQ);
+	set_irq_chained_handler(IRQ_CAM, s3c_irq_demux_cam);
+
+	for (irqno = IRQ_S3C2440_CAM_C; irqno <= IRQ_S3C2440_CAM_P; irqno++) {
+		set_irq_chip(irqno, &s3c_irq_cam);
+		set_irq_handler(irqno, do_level_IRQ);
+		set_irq_flags(irqno, IRQF_VALID);
+	}
+
+	return 0;
+}
+
+static struct sysdev_driver s3c244x_irq_driver = {
+	.add	= s3c244x_irq_add,
+};
+
+static int s3c2440_irq_init(void)
+{
+	return sysdev_driver_register(&s3c2440_sysclass, &s3c244x_irq_driver);
+}
+
+arch_initcall(s3c2440_irq_init);
+
+
+static int s3c2442_irq_init(void)
+{
+	return sysdev_driver_register(&s3c2442_sysclass, &s3c244x_irq_driver);
+}
+
+arch_initcall(s3c2442_irq_init);
diff --git a/arch/arm/mach-s3c2410/s3c244x.c b/arch/arm/mach-s3c2410/s3c244x.c
new file mode 100644
index 0000000..96852a7
--- /dev/null
+++ b/arch/arm/mach-s3c2410/s3c244x.c
@@ -0,0 +1,182 @@
+/* linux/arch/arm/mach-s3c2410/s3c244x.c
+ *
+ * Copyright (c) 2004-2006 Simtec Electronics
+ *   Ben Dooks <ben@simtec.co.uk>
+ *
+ * Samsung S3C2440 and S3C2442 Mobile CPU support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/sysdev.h>
+#include <linux/clk.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+
+#include <asm/arch/regs-clock.h>
+#include <asm/arch/regs-serial.h>
+#include <asm/arch/regs-gpio.h>
+#include <asm/arch/regs-gpioj.h>
+#include <asm/arch/regs-dsc.h>
+
+#include "s3c2440.h"
+#include "s3c244x.h"
+#include "clock.h"
+#include "devs.h"
+#include "cpu.h"
+#include "pm.h"
+
+static struct map_desc s3c244x_iodesc[] __initdata = {
+	IODESC_ENT(CLKPWR),
+	IODESC_ENT(TIMER),
+	IODESC_ENT(WATCHDOG),
+	IODESC_ENT(LCD),
+	IODESC_ENT(ADC),
+	IODESC_ENT(USBHOST),
+};
+
+/* uart initialisation */
+
+void __init s3c244x_init_uarts(struct s3c2410_uartcfg *cfg, int no)
+{
+	s3c24xx_init_uartdevs("s3c2440-uart", s3c2410_uart_resources, cfg, no);
+}
+
+void __init s3c244x_map_io(struct map_desc *mach_desc, int size)
+{
+	/* register our io-tables */
+
+	iotable_init(s3c244x_iodesc, ARRAY_SIZE(s3c244x_iodesc));
+	iotable_init(mach_desc, size);
+
+	/* rename any peripherals used differing from the s3c2410 */
+
+	s3c_device_i2c.name  = "s3c2440-i2c";
+	s3c_device_nand.name = "s3c2440-nand";
+}
+
+void __init s3c244x_init_clocks(int xtal)
+{
+	unsigned long clkdiv;
+	unsigned long camdiv;
+	unsigned long hclk, fclk, pclk;
+	int hdiv = 1;
+
+	/* now we've got our machine bits initialised, work out what
+	 * clocks we've got */
+
+	fclk = s3c2410_get_pll(__raw_readl(S3C2410_MPLLCON), xtal) * 2;
+
+	clkdiv = __raw_readl(S3C2410_CLKDIVN);
+	camdiv = __raw_readl(S3C2440_CAMDIVN);
+
+	/* work out clock scalings */
+
+	switch (clkdiv & S3C2440_CLKDIVN_HDIVN_MASK) {
+	case S3C2440_CLKDIVN_HDIVN_1:
+		hdiv = 1;
+		break;
+
+	case S3C2440_CLKDIVN_HDIVN_2:
+		hdiv = 2;
+		break;
+
+	case S3C2440_CLKDIVN_HDIVN_4_8:
+		hdiv = (camdiv & S3C2440_CAMDIVN_HCLK4_HALF) ? 8 : 4;
+		break;
+
+	case S3C2440_CLKDIVN_HDIVN_3_6:
+		hdiv = (camdiv & S3C2440_CAMDIVN_HCLK3_HALF) ? 6 : 3;
+		break;
+	}
+
+	hclk = fclk / hdiv;
+	pclk = hclk / ((clkdiv & S3C2440_CLKDIVN_PDIVN)? 2:1);
+
+	/* print brief summary of clocks, etc */
+
+	printk("S3C244X: core %ld.%03ld MHz, memory %ld.%03ld MHz, peripheral %ld.%03ld MHz\n",
+	       print_mhz(fclk), print_mhz(hclk), print_mhz(pclk));
+
+	/* initialise the clocks here, to allow other things like the
+	 * console to use them, and to add new ones after the initialisation
+	 */
+
+	s3c24xx_setup_clocks(xtal, fclk, hclk, pclk);
+}
+
+#ifdef CONFIG_PM
+
+static struct sleep_save s3c244x_sleep[] = {
+	SAVE_ITEM(S3C2440_DSC0),
+	SAVE_ITEM(S3C2440_DSC1),
+	SAVE_ITEM(S3C2440_GPJDAT),
+	SAVE_ITEM(S3C2440_GPJCON),
+	SAVE_ITEM(S3C2440_GPJUP)
+};
+
+static int s3c244x_suspend(struct sys_device *dev, pm_message_t state)
+{
+	s3c2410_pm_do_save(s3c244x_sleep, ARRAY_SIZE(s3c244x_sleep));
+	return 0;
+}
+
+static int s3c244x_resume(struct sys_device *dev)
+{
+	s3c2410_pm_do_restore(s3c244x_sleep, ARRAY_SIZE(s3c244x_sleep));
+	return 0;
+}
+
+#else
+#define s3c244x_suspend NULL
+#define s3c244x_resume  NULL
+#endif
+
+/* Since the S3C2442 and S3C2440 share  items, put both sysclasses here */
+
+struct sysdev_class s3c2440_sysclass = {
+	set_kset_name("s3c2440-core"),
+	.suspend	= s3c244x_suspend,
+	.resume		= s3c244x_resume
+};
+
+struct sysdev_class s3c2442_sysclass = {
+	set_kset_name("s3c2442-core"),
+	.suspend	= s3c244x_suspend,
+	.resume		= s3c244x_resume
+};
+
+/* need to register class before we actually register the device, and
+ * we also need to ensure that it has been initialised before any of the
+ * drivers even try to use it (even if not on an s3c2440 based system)
+ * as a driver which may support both 2410 and 2440 may try and use it.
+*/
+
+static int __init s3c2440_core_init(void)
+{
+	return sysdev_class_register(&s3c2440_sysclass);
+}
+
+core_initcall(s3c2440_core_init);
+
+static int __init s3c2442_core_init(void)
+{
+	return sysdev_class_register(&s3c2442_sysclass);
+}
+
+core_initcall(s3c2442_core_init);
diff --git a/arch/arm/mach-s3c2410/s3c244x.h b/arch/arm/mach-s3c2410/s3c244x.h
new file mode 100644
index 0000000..3e7f5f7
--- /dev/null
+++ b/arch/arm/mach-s3c2410/s3c244x.h
@@ -0,0 +1,25 @@
+/* arch/arm/mach-s3c2410/s3c2440.h
+ *
+ * Copyright (c) 2004-2005 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * Header file for S3C2440 and S3C2442 cpu support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442)
+
+extern void s3c244x_map_io(struct map_desc *mach_desc, int size);
+
+extern void s3c244x_init_uarts(struct s3c2410_uartcfg *cfg, int no);
+
+extern void s3c244x_init_clocks(int xtal);
+
+#else
+#define s3c244x_init_clocks NULL
+#define s3c244x_init_uarts NULL
+#define s3c244x_map_io NULL
+#endif
diff --git a/arch/arm/mach-s3c2410/sleep.S b/arch/arm/mach-s3c2410/sleep.S
index 73de2ea..5f6761e 100644
--- a/arch/arm/mach-s3c2410/sleep.S
+++ b/arch/arm/mach-s3c2410/sleep.S
@@ -66,7 +66,9 @@
 	@@ flush the caches to ensure everything is back out to
 	@@ SDRAM before the core powers down
 
+#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH
 	bl	arm920_flush_kern_cache_all
+#endif
 
 	@@ prepare cpu to sleep
 
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index c55b739..1ff2f07 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -121,8 +121,8 @@
 # ARM926T
 config CPU_ARM926T
 	bool "Support ARM926T processor"
-	depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB
-	default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX
+	depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008
+	default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008
 	select CPU_32v5
 	select CPU_ABRT_EV5TJ
 	select CPU_CACHE_VIVT
diff --git a/drivers/net/smc91x.h b/drivers/net/smc91x.h
index f72a4f5..bf776125c 100644
--- a/drivers/net/smc91x.h
+++ b/drivers/net/smc91x.h
@@ -260,15 +260,17 @@
 #define RPC_LSA_DEFAULT		RPC_LED_TX_RX
 #define RPC_LSB_DEFAULT		RPC_LED_100_10
 
-#elif	defined(CONFIG_MACH_LPD7A400) || defined(CONFIG_MACH_LPD7A404)
+#elif   defined(CONFIG_MACH_LPD79520) \
+     || defined(CONFIG_MACH_LPD7A400) \
+     || defined(CONFIG_MACH_LPD7A404)
 
-/* The LPD7A40X_IOBARRIER is necessary to overcome a mismatch between
- * the way that the CPU handles chip selects and the way that the SMC
- * chip expects the chip select to operate.  Refer to
+/* The LPD7X_IOBARRIER is necessary to overcome a mismatch between the
+ * way that the CPU handles chip selects and the way that the SMC chip
+ * expects the chip select to operate.  Refer to
  * Documentation/arm/Sharp-LH/IOBarrier for details.  The read from
- * IOBARRIER is a byte as a least-common denominator of possible
- * regions to use as the barrier.  It would be wasteful to read 32
- * bits from a byte oriented region.
+ * IOBARRIER is a byte, in order that we read the least-common
+ * denominator.  It would be wasteful to read 32 bits from an 8-bit
+ * accessible region.
  *
  * There is no explicit protection against interrupts intervening
  * between the writew and the IOBARRIER.  In SMC ISR there is a
@@ -287,25 +289,35 @@
 #define SMC_CAN_USE_16BIT	1
 #define SMC_CAN_USE_32BIT	0
 #define SMC_NOWAIT		0
-#define LPD7A40X_IOBARRIER	readb (IOBARRIER_VIRT)
+#define LPD7X_IOBARRIER		readb (IOBARRIER_VIRT)
 
-#define SMC_inw(a,r)		readw ((void*) ((a) + (r)))
-#define SMC_insw(a,r,p,l)	readsw ((void*) ((a) + (r)), p, l)
-#define SMC_outw(v,a,r)	     ({ writew ((v), (a) + (r)); LPD7A40X_IOBARRIER; })
+#define SMC_inw(a,r)\
+   ({ unsigned short v = readw ((void*) ((a) + (r))); LPD7X_IOBARRIER; v; })
+#define SMC_outw(v,a,r)	  ({ writew ((v), (a) + (r)); LPD7X_IOBARRIER; })
 
-#define SMC_outsw		LPD7A40X_SMC_outsw
+#define SMC_insw		LPD7_SMC_insw
+static inline void LPD7_SMC_insw (unsigned char* a, int r,
+				  unsigned char* p, int l)
+{
+	unsigned short* ps = (unsigned short*) p;
+	while (l-- > 0) {
+		*ps++ = readw (a + r);
+		LPD7X_IOBARRIER;
+	}
+}
 
-static inline void LPD7A40X_SMC_outsw(unsigned long a, int r,
-				     unsigned char* p, int l)
+#define SMC_outsw		LPD7_SMC_outsw
+static inline void LPD7_SMC_outsw (unsigned char* a, int r,
+				   unsigned char* p, int l)
 {
 	unsigned short* ps = (unsigned short*) p;
 	while (l-- > 0) {
 		writew (*ps++, a + r);
-		LPD7A40X_IOBARRIER;
+		LPD7X_IOBARRIER;
 	}
 }
 
-#define SMC_INTERRUPT_PREAMBLE	LPD7A40X_IOBARRIER
+#define SMC_INTERRUPT_PREAMBLE	LPD7X_IOBARRIER
 
 #define RPC_LSA_DEFAULT		RPC_LED_TX_RX
 #define RPC_LSB_DEFAULT		RPC_LED_100_10
diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c
index f5aac92..53c2465 100644
--- a/drivers/serial/s3c2410.c
+++ b/drivers/serial/s3c2410.c
@@ -1365,7 +1365,7 @@
 
 #endif /* CONFIG_CPU_S3C2410 */
 
-#ifdef CONFIG_CPU_S3C2440
+#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442)
 
 static int s3c2440_serial_setsource(struct uart_port *port,
 				     struct s3c24xx_uart_clksrc *clk)
diff --git a/drivers/serial/serial_lh7a40x.c b/drivers/serial/serial_lh7a40x.c
index aa521b8..776d4ff 100644
--- a/drivers/serial/serial_lh7a40x.c
+++ b/drivers/serial/serial_lh7a40x.c
@@ -145,14 +145,15 @@
 {
 	struct tty_struct* tty = port->info->tty;
 	int cbRxMax = 256;	/* (Gross) limit on receive */
-	unsigned int data, flag;/* Received data and status */
+	unsigned int data;	/* Received data and status */
+	unsigned int flag;
 
 	while (!(UR (port, UART_R_STATUS) & nRxRdy) && --cbRxMax) {
 		data = UR (port, UART_R_DATA);
 		flag = TTY_NORMAL;
 		++port->icount.rx;
 
-		if (unlikely(data & RxError)) {	/* Quick check, short-circuit */
+		if (unlikely(data & RxError)) {
 			if (data & RxBreak) {
 				data &= ~(RxFramingError | RxParityError);
 				++port->icount.brk;
@@ -303,7 +304,7 @@
 	/* Note, kernel appears to be setting DTR and RTS on console. */
 
 	/* *** FIXME: this deserves more work.  There's some work in
-               tracing all of the IO pins. */
+	       tracing all of the IO pins. */
 #if 0
 	if( port->mapbase == UART1_PHYS) {
 		gpioRegs_t *gpio = (gpioRegs_t *)IO_ADDRESS(GPIO_PHYS);
@@ -662,9 +663,13 @@
 	if (ret == 0) {
 		int i;
 
-		for (i = 0; i < DEV_NR; i++)
+		for (i = 0; i < DEV_NR; i++) {
+			/* UART3, when used, requires GPIO pin reallocation */
+			if (lh7a40x_ports[i].port.mapbase == UART3_PHYS)
+				GPIO_PINMUX |= 1<<3;
 			uart_add_one_port (&lh7a40x_reg,
 					   &lh7a40x_ports[i].port);
+		}
 	}
 	return ret;
 }
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 5641498..5a2840a 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -167,6 +167,69 @@
 	  here and read <file:Documentation/modules.txt>.  The module
 	  will be called amba-clcd.
 
+choice
+
+	depends on FB_ARMCLCD && (ARCH_LH7A40X || ARCH_LH7952X)
+	prompt "LCD Panel"
+	default FB_ARMCLCD_SHARP_LQ035Q7DB02
+
+config FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
+	bool "LogicPD LCD 3.5\" QVGA w/HRTFT IC"
+	help
+	  This is an implementation of the Sharp LQ035Q7DB02, a 3.5"
+	  color QVGA, HRTFT panel.  The LogicPD device includes an
+	  an integrated HRTFT controller IC.
+	  The native resolution is 240x320.
+
+config FB_ARMCLCD_SHARP_LQ057Q3DC02
+	bool "LogicPD LCD 5.7\" QVGA"
+	help
+	  This is an implementation of the Sharp LQ057Q3DC02, a 5.7"
+	  color QVGA, TFT panel.  The LogicPD device includes an
+	  The native resolution is 320x240.
+
+config FB_ARMCLCD_SHARP_LQ64D343
+	bool "LogicPD LCD 6.4\" VGA"
+	help
+	  This is an implementation of the Sharp LQ64D343, a 6.4"
+	  color VGA, TFT panel.  The LogicPD device includes an
+	  The native resolution is 640x480.
+
+config FB_ARMCLCD_SHARP_LQ10D368
+	bool "LogicPD LCD 10.4\" VGA"
+	help
+	  This is an implementation of the Sharp LQ10D368, a 10.4"
+	  color VGA, TFT panel.  The LogicPD device includes an
+	  The native resolution is 640x480.
+
+
+config FB_ARMCLCD_SHARP_LQ121S1DG41
+	bool "LogicPD LCD 12.1\" SVGA"
+	help
+	  This is an implementation of the Sharp LQ121S1DG41, a 12.1"
+	  color SVGA, TFT panel.  The LogicPD device includes an
+	  The native resolution is 800x600.
+
+	  This panel requires a clock rate may be an integer fraction
+	  of the base LCDCLK frequency.  The driver will select the
+	  highest frequency available that is lower than the maximum
+	  allowed.  The panel may flicker if the clock rate is
+	  slower than the recommended minimum.
+
+config FB_ARMCLCD_AUO_A070VW01_WIDE
+	bool "AU Optronics A070VW01 LCD 7.0\" WIDE"
+	help
+	  This is an implementation of the AU Optronics, a 7.0"
+	  WIDE Color.  The native resolution is 234x480.
+
+config FB_ARMCLCD_HITACHI
+	bool "Hitachi Wide Screen 800x480"
+	help
+	  This is an implementation of the Hitachi 800x480.
+
+endchoice
+
+
 config FB_ACORN
 	bool "Acorn VIDC support"
 	depends on (FB = y) && ARM && (ARCH_ACORN || ARCH_CLPS7500)
diff --git a/include/asm-arm/arch-lh7a40x/clocks.h b/include/asm-arm/arch-lh7a40x/clocks.h
new file mode 100644
index 0000000..bee02fd
--- /dev/null
+++ b/include/asm-arm/arch-lh7a40x/clocks.h
@@ -0,0 +1,20 @@
+/* include/asm-arm/arch-lh7a40x/clocks.h
+ *
+ *  Copyright (C) 2004 Marc Singer
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License
+ *  version 2 as published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/config.h>
+
+#ifndef __ASM_ARCH_CLOCKS_H
+#define __ASM_ARCH_CLOCKS_H
+
+unsigned int fclkfreq_get (void);
+unsigned int hclkfreq_get (void);
+unsigned int pclkfreq_get (void);
+
+#endif  /* _ASM_ARCH_CLOCKS_H */
diff --git a/include/asm-arm/arch-lh7a40x/constants.h b/include/asm-arm/arch-lh7a40x/constants.h
index 52c1cb9..2929e89 100644
--- a/include/asm-arm/arch-lh7a40x/constants.h
+++ b/include/asm-arm/arch-lh7a40x/constants.h
@@ -29,8 +29,7 @@
 
 #if defined (CONFIG_MACH_LPD7A400) || defined (CONFIG_MACH_LPD7A404)
 
-# define IOBARRIER_PHYS		0xc0000000 /* Start of SDRAM */
-/*# define IOBARRIER_PHYS		0x00000000 */ /* Start of flash */
+# define IOBARRIER_PHYS		0x10000000 /* Second bank, fastest timing */
 # define IOBARRIER_VIRT		0xf0000000
 # define IOBARRIER_SIZE		PAGE_SIZE
 
@@ -53,6 +52,9 @@
 # define CPLD08_PHYS		CPLDX_PHYS (0x08)
 # define CPLD08_VIRT		CPLDX_VIRT (0x08)
 # define CPLD08_SIZE		PAGE_SIZE
+# define CPLD0A_PHYS		CPLDX_PHYS (0x0a)
+# define CPLD0A_VIRT		CPLDX_VIRT (0x0a)
+# define CPLD0A_SIZE		PAGE_SIZE
 # define CPLD0C_PHYS		CPLDX_PHYS (0x0c)
 # define CPLD0C_VIRT		CPLDX_VIRT (0x0c)
 # define CPLD0C_SIZE		PAGE_SIZE
@@ -84,5 +86,7 @@
 #define	XTAL_IN			14745600	/* 14.7456 MHz crystal */
 #define PLL_CLOCK		(XTAL_IN * 21)	/* 309 MHz PLL clock */
 #define MAX_HCLK_KHZ		100000		/* HCLK max limit ~100MHz */
+#define HCLK			(99993600)
+//#define HCLK			(119808000)
 
 #endif /* __ASM_ARCH_CONSTANTS_H */
diff --git a/include/asm-arm/arch-lh7a40x/dma.h b/include/asm-arm/arch-lh7a40x/dma.h
index 15492e3..a8cbd14 100644
--- a/include/asm-arm/arch-lh7a40x/dma.h
+++ b/include/asm-arm/arch-lh7a40x/dma.h
@@ -1,9 +1,86 @@
 /* include/asm-arm/arch-lh7a40x/dma.h
  *
- *  Copyright (C) 2003 Coastal Environmental Systems
+ *  Copyright (C) 2005 Marc Singer
  *
  *  This program is free software; you can redistribute it and/or
  *  modify it under the terms of the GNU General Public License
  *  version 2 as published by the Free Software Foundation.
  *
  */
+
+typedef enum {
+	DMA_M2M0	= 0,
+	DMA_M2M1	= 1,
+	DMA_M2P0	= 2,	/* Tx */
+	DMA_M2P1	= 3,	/* Rx */
+	DMA_M2P2	= 4,	/* Tx */
+	DMA_M2P3	= 5,	/* Rx */
+	DMA_M2P4	= 6,	/* Tx - AC97 */
+	DMA_M2P5	= 7,	/* Rx - AC97 */
+	DMA_M2P6	= 8,	/* Tx */
+	DMA_M2P7	= 9,	/* Rx */
+} dma_device_t;
+
+#define DMA_LENGTH_MAX		((64*1024) - 4) /* bytes */
+
+#define DMAC_GCA		__REG(DMAC_PHYS + 0x2b80)
+#define DMAC_GIR		__REG(DMAC_PHYS + 0x2bc0)
+
+#define DMAC_GIR_MMI1		(1<<11)
+#define DMAC_GIR_MMI0		(1<<10)
+#define DMAC_GIR_MPI8		(1<<9)
+#define DMAC_GIR_MPI9		(1<<8)
+#define DMAC_GIR_MPI6		(1<<7)
+#define DMAC_GIR_MPI7		(1<<6)
+#define DMAC_GIR_MPI4		(1<<5)
+#define DMAC_GIR_MPI5		(1<<4)
+#define DMAC_GIR_MPI2		(1<<3)
+#define DMAC_GIR_MPI3		(1<<2)
+#define DMAC_GIR_MPI0		(1<<1)
+#define DMAC_GIR_MPI1		(1<<0)
+
+#define DMAC_M2P0		0x0000
+#define DMAC_M2P1		0x0040
+#define DMAC_M2P2		0x0080
+#define DMAC_M2P3		0x00c0
+#define DMAC_M2P4		0x0240
+#define DMAC_M2P5		0x0200
+#define DMAC_M2P6		0x02c0
+#define DMAC_M2P7		0x0280
+#define DMAC_M2P8		0x0340
+#define DMAC_M2P9		0x0300
+#define DMAC_M2M0		0x0100
+#define DMAC_M2M1		0x0140
+
+#define DMAC_P_PCONTROL(c)	__REG(DMAC_PHYS + (c) + 0x00)
+#define DMAC_P_PINTERRUPT(c)	__REG(DMAC_PHYS + (c) + 0x04)
+#define DMAC_P_PPALLOC(c)	__REG(DMAC_PHYS + (c) + 0x08)
+#define DMAC_P_PSTATUS(c)	__REG(DMAC_PHYS + (c) + 0x0c)
+#define DMAC_P_REMAIN(c)	__REG(DMAC_PHYS + (c) + 0x14)
+#define DMAC_P_MAXCNT0(c)	__REG(DMAC_PHYS + (c) + 0x20)
+#define DMAC_P_BASE0(c)		__REG(DMAC_PHYS + (c) + 0x24)
+#define DMAC_P_CURRENT0(c)	__REG(DMAC_PHYS + (c) + 0x28)
+#define DMAC_P_MAXCNT1(c)	__REG(DMAC_PHYS + (c) + 0x30)
+#define DMAC_P_BASE1(c)		__REG(DMAC_PHYS + (c) + 0x34)
+#define DMAC_P_CURRENT1(c)	__REG(DMAC_PHYS + (c) + 0x38)
+
+#define DMAC_PCONTROL_ENABLE	(1<<4)
+
+#define DMAC_PORT_USB		0
+#define DMAC_PORT_SDMMC		1
+#define DMAC_PORT_AC97_1	2
+#define DMAC_PORT_AC97_2	3
+#define DMAC_PORT_AC97_3	4
+#define DMAC_PORT_UART1		6
+#define DMAC_PORT_UART2		7
+#define DMAC_PORT_UART3		8
+
+#define DMAC_PSTATUS_CURRSTATE_SHIFT	4
+#define DMAC_PSTATUS_CURRSTATE_MASK	0x3
+
+#define DMAC_PSTATUS_NEXTBUF	 (1<<6)
+#define DMAC_PSTATUS_STALLRINT	 (1<<0)
+
+#define DMAC_INT_CHE		 (1<<3)
+#define DMAC_INT_NFB		 (1<<1)
+#define DMAC_INT_STALL		 (1<<0)
diff --git a/include/asm-arm/arch-lh7a40x/entry-macro.S b/include/asm-arm/arch-lh7a40x/entry-macro.S
index a2f67c0..9fc7f49 100644
--- a/include/asm-arm/arch-lh7a40x/entry-macro.S
+++ b/include/asm-arm/arch-lh7a40x/entry-macro.S
@@ -10,11 +10,73 @@
 #include <asm/hardware.h>
 #include <asm/arch/irqs.h>
 
-# if defined (CONFIG_ARCH_LH7A400) && defined (CONFIG_ARCH_LH7A404)
-#  error "LH7A400 and LH7A404 are mutually exclusive"
-# endif
+/* In order to allow there to be support for both of the processor
+   classes at the same time, we make a hack here that isn't very
+   pretty.  At startup, the link pointed to with the
+   branch_irq_lh7a400 symbol is replaced with a NOP when the CPU is
+   detected as a lh7a404.
 
-# if defined (CONFIG_ARCH_LH7A400)
+   *** FIXME: we should clean this up so that there is only one
+	      implementation for each CPU's design.
+
+*/
+
+#if defined (CONFIG_ARCH_LH7A400) && defined (CONFIG_ARCH_LH7A404)
+
+		.macro	disable_fiq
+		.endm
+
+		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
+
+branch_irq_lh7a400: b 1000f
+
+@ Implementation of the LH7A404 get_irqnr_and_base.
+
+		mov	\irqnr, #0			@ VIC1 irq base
+		mov	\base, #io_p2v(0x80000000)	@ APB registers
+		add	\base, \base, #0x8000
+		ldr	\tmp, [\base, #0x0030]		@ VIC1_VECTADDR
+		tst	\tmp, #VA_VECTORED		@ Direct vectored
+		bne	1002f
+		tst	\tmp, #VA_VIC1DEFAULT		@ Default vectored VIC1
+		ldrne	\irqstat, [\base, #0]		@ VIC1_IRQSTATUS
+		bne	1001f
+		add	\base, \base, #(0xa000 - 0x8000)
+		ldr	\tmp, [\base, #0x0030]		@ VIC2_VECTADDR
+		tst	\tmp, #VA_VECTORED		@ Direct vectored
+		bne	1002f
+		ldr	\irqstat, [\base, #0]		@ VIC2_IRQSTATUS
+		mov	\irqnr, #32			@ VIC2 irq base
+
+1001:		movs	\irqstat, \irqstat, lsr #1	@ Shift into carry
+		bcs	1008f				@ Bit set; irq found
+		add	\irqnr, \irqnr, #1
+		bne	1001b				@ Until no bits
+		b	1009f				@ Nothing?  Hmm.
+1002:		and	\irqnr, \tmp, #0x3f		@ Mask for valid bits
+1008:		movs	\irqstat, #1			@ Force !Z
+		str	\tmp, [\base, #0x0030]		@ Clear vector
+		b	1009f
+
+@ Implementation of the LH7A400 get_irqnr_and_base.
+
+1000:		mov	\irqnr, #0
+		mov	\base, #io_p2v(0x80000000)	@ APB registers
+		ldr	\irqstat, [\base, #0x500]	@ PIC INTSR
+
+1001:		movs	\irqstat, \irqstat, lsr #1	@ Shift into carry
+		bcs	1008f				@ Bit set; irq found
+		add	\irqnr, \irqnr, #1
+		bne	1001b				@ Until no bits
+		b	1009f				@ Nothing?  Hmm.
+1008:		movs	\irqstat, #1			@ Force !Z
+
+1009:
+               .endm
+
+
+
+#elif defined (CONFIG_ARCH_LH7A400)
 		.macro	disable_fiq
 		.endm
 
diff --git a/include/asm-arm/arch-lh7a40x/hardware.h b/include/asm-arm/arch-lh7a40x/hardware.h
index aeb07c1..e9ff74f 100644
--- a/include/asm-arm/arch-lh7a40x/hardware.h
+++ b/include/asm-arm/arch-lh7a40x/hardware.h
@@ -13,6 +13,8 @@
 #ifndef __ASM_ARCH_HARDWARE_H
 #define __ASM_ARCH_HARDWARE_H
 
+#include <asm/sizes.h>		/* Added for the sake of amba-clcd driver */
+
 #define io_p2v(x) (0xf0000000 | (((x) & 0xfff00000) >> 4) | ((x) & 0x0000ffff))
 #define io_v2p(x) (             (((x) & 0x0fff0000) << 4) | ((x) & 0x0000ffff))
 
@@ -53,6 +55,8 @@
 
 #endif
 
+#define MASK_AND_SET(v,m,s)	(v) = ((v)&~(m))|(s)
+
 #include "registers.h"
 
 #endif  /* _ASM_ARCH_HARDWARE_H */
diff --git a/include/asm-arm/arch-lh7a40x/irqs.h b/include/asm-arm/arch-lh7a40x/irqs.h
index f91f3e5..7e8a217 100644
--- a/include/asm-arm/arch-lh7a40x/irqs.h
+++ b/include/asm-arm/arch-lh7a40x/irqs.h
@@ -154,9 +154,10 @@
 #if !defined (IRQ_GPIO0INTR)
 # define IRQ_GPIO0INTR	IRQ_GPIO0FIQ
 #endif
-#define IRQ_TICK 	IRQ_TINTR
+#define IRQ_TICK	IRQ_TINTR
 #define IRQ_PCC1_RDY	IRQ_GPIO6INTR	/* PCCard 1 ready */
 #define IRQ_PCC2_RDY	IRQ_GPIO7INTR	/* PCCard 2 ready */
+#define IRQ_USB		IRQ_USBINTR	/* USB device */
 
 #ifdef CONFIG_MACH_KEV7A400
 # define IRQ_TS		IRQ_GPIOFIQ	/* Touchscreen */
@@ -191,6 +192,10 @@
 # define IRQ_LPD7A400_TS	IRQ_LPD7A40X_CPLD + 1	/* Touch screen */
 #endif
 
+#if defined (CONFIG_MACH_LPD7A400)
+# define IRQ_TOUCH		IRQ_LPD7A400_TS
+#endif
+
 #define NR_IRQS		(NR_IRQ_CPU + NR_IRQ_BOARD)
 
 #endif
diff --git a/include/asm-arm/arch-lh7a40x/registers.h b/include/asm-arm/arch-lh7a40x/registers.h
index 2edb22e..544307b 100644
--- a/include/asm-arm/arch-lh7a40x/registers.h
+++ b/include/asm-arm/arch-lh7a40x/registers.h
@@ -18,7 +18,7 @@
 
 	/* Physical register base addresses */
 
-#define AC97_PHYS	(0x80000000)	/* AC97 Controller */
+#define AC97C_PHYS	(0x80000000)	/* AC97 Controller */
 #define MMC_PHYS	(0x80000100)	/* Multimedia Card Controller */
 #define USB_PHYS	(0x80000200)	/* USB Client */
 #define SCI_PHYS	(0x80000300)	/* Secure Card Interface */
@@ -35,6 +35,8 @@
 #define RTC_PHYS	(0x80000d00)	/* Real-time Clock */
 #define GPIO_PHYS	(0x80000e00)	/* General Purpose IO */
 #define BMI_PHYS	(0x80000f00)	/* Battery Monitor Interface */
+#define HRTFTC_PHYS	(0x80001000)	/* High-res TFT Controller (LH7A400) */
+#define ALI_PHYS	(0x80001000)	/* Advanced LCD Interface (LH7A404) */
 #define WDT_PHYS	(0x80001400)	/* Watchdog Timer */
 #define SMC_PHYS	(0x80002000)	/* Static Memory Controller */
 #define SDRC_PHYS	(0x80002400)	/* SDRAM Controller */
@@ -43,6 +45,7 @@
 
 	/* Physical registers of the LH7A404 */
 
+#define ADC_PHYS	(0x80001300)	/* A/D & Touchscreen Controller */
 #define VIC1_PHYS	(0x80008000)	/* Vectored Interrupt Controller 1 */
 #define USBH_PHYS	(0x80009000)	/* USB OHCI host controller */
 #define VIC2_PHYS	(0x8000a000)	/* Vectored Interrupt Controller 2 */
@@ -53,10 +56,32 @@
 
 	/* Clock/State Controller register */
 
+#define CSC_PWRSR	__REG(CSC_PHYS + 0x00) /* Reset register & ID */
 #define CSC_PWRCNT	__REG(CSC_PHYS + 0x04) /* Power control */
+#define CSC_CLKSET	__REG(CSC_PHYS + 0x20) /* Clock speed control */
+#define CSC_USBDRESET	__REG(CSC_PHYS + 0x4c) /* USB Device resets */
 
 #define CSC_PWRCNT_USBH_EN	(1<<28)	/* USB Host power enable */
+#define CSC_PWRCNT_DMAC_M2M1_EN	(1<<27)
+#define CSC_PWRCNT_DMAC_M2M0_EN	(1<<26)
+#define CSC_PWRCNT_DMAC_M2P8_EN	(1<<25)
+#define CSC_PWRCNT_DMAC_M2P9_EN	(1<<24)
+#define CSC_PWRCNT_DMAC_M2P6_EN	(1<<23)
+#define CSC_PWRCNT_DMAC_M2P7_EN	(1<<22)
+#define CSC_PWRCNT_DMAC_M2P4_EN	(1<<21)
+#define CSC_PWRCNT_DMAC_M2P5_EN	(1<<20)
+#define CSC_PWRCNT_DMAC_M2P2_EN	(1<<19)
+#define CSC_PWRCNT_DMAC_M2P3_EN	(1<<18)
+#define CSC_PWRCNT_DMAC_M2P0_EN	(1<<17)
+#define CSC_PWRCNT_DMAC_M2P1_EN	(1<<16)
 
+#define CSC_PWRSR_CHIPMAN_SHIFT	(24)
+#define CSC_PWRSR_CHIPMAN_MASK	(0xff)
+#define CSC_PWRSR_CHIPID_SHIFT	(16)
+#define CSC_PWRSR_CHIPID_MASK	(0xff)
+
+#define CSC_USBDRESET_APBRESETREG	(1<<1)
+#define CSC_USBDRESET_IORESETREG	(1<<0)
 
 	/* Interrupt Controller registers */
 
@@ -109,6 +134,13 @@
 #define GPIO_GPIOFEOI	__REG(GPIO_PHYS + 0x54)	/* GPIO End-of-Interrupt */
 #define GPIO_GPIOINTEN	__REG(GPIO_PHYS + 0x58)	/* GPIO Interrupt Enable */
 #define GPIO_INTSTATUS	__REG(GPIO_PHYS + 0x5c)	/* GPIO Interrupt Status */
+#define GPIO_PINMUX	__REG(GPIO_PHYS + 0x2c)
+#define GPIO_PADD	__REG(GPIO_PHYS + 0x10)
+#define GPIO_PAD	__REG(GPIO_PHYS + 0x00)
+#define GPIO_PCD	__REG(GPIO_PHYS + 0x08)
+#define GPIO_PCDD	__REG(GPIO_PHYS + 0x18)
+#define GPIO_PEDD	__REG(GPIO_PHYS + 0x24)
+#define GPIO_PED	__REG(GPIO_PHYS + 0x20)
 
 
 	/* Static Memory Controller registers */
@@ -138,20 +170,21 @@
 #endif
 
 #if defined (CONFIG_MACH_LPD7A400) || defined (CONFIG_MACH_LPD7A404)
-# define CPLD_CONTROL		__REG8(CPLD02_PHYS)
-# define CPLD_SPI_DATA		__REG8(CPLD06_PHYS)
-# define CPLD_SPI_CONTROL	__REG8(CPLD08_PHYS)
-# define CPLD_SPI_EEPROM	__REG8(CPLD0A_PHYS)
-# define CPLD_INTERRUPTS	__REG8(CPLD0C_PHYS) /* IRQ mask/status */
-# define CPLD_BOOT_MODE		__REG8(CPLD0E_PHYS)
-# define CPLD_FLASH		__REG8(CPLD10_PHYS)
-# define CPLD_POWER_MGMT	__REG8(CPLD12_PHYS)
-# define CPLD_REVISION		__REG8(CPLD14_PHYS)
-# define CPLD_GPIO_EXT		__REG8(CPLD16_PHYS)
-# define CPLD_GPIO_DATA		__REG8(CPLD18_PHYS)
-# define CPLD_GPIO_DIR		__REG8(CPLD1A_PHYS)
-#endif
 
+# define CPLD_CONTROL		__REG16(CPLD02_PHYS)
+# define CPLD_SPI_DATA		__REG16(CPLD06_PHYS)
+# define CPLD_SPI_CONTROL	__REG16(CPLD08_PHYS)
+# define CPLD_SPI_EEPROM	__REG16(CPLD0A_PHYS)
+# define CPLD_INTERRUPTS	__REG16(CPLD0C_PHYS) /* IRQ mask/status */
+# define CPLD_BOOT_MODE		__REG16(CPLD0E_PHYS)
+# define CPLD_FLASH		__REG16(CPLD10_PHYS)
+# define CPLD_POWER_MGMT	__REG16(CPLD12_PHYS)
+# define CPLD_REVISION		__REG16(CPLD14_PHYS)
+# define CPLD_GPIO_EXT		__REG16(CPLD16_PHYS)
+# define CPLD_GPIO_DATA		__REG16(CPLD18_PHYS)
+# define CPLD_GPIO_DIR		__REG16(CPLD1A_PHYS)
+
+#endif
 
 	/* Timer registers */
 
@@ -190,4 +223,3 @@
 
 
 #endif  /* _ASM_ARCH_REGISTERS_H */
-
diff --git a/include/asm-arm/arch-lh7a40x/ssp.h b/include/asm-arm/arch-lh7a40x/ssp.h
new file mode 100644
index 0000000..132b1c4
--- /dev/null
+++ b/include/asm-arm/arch-lh7a40x/ssp.h
@@ -0,0 +1,71 @@
+/* ssp.h
+     $Id$
+
+   written by Marc Singer
+   6 Dec 2004
+
+   Copyright (C) 2004 Marc Singer
+
+   -----------
+   DESCRIPTION
+   -----------
+
+   This SSP header is available throughout the kernel, for this
+   machine/architecture, because drivers that use it may be dispersed.
+
+   This file was cloned from the 7952x implementation.  It would be
+   better to share them, but we're taking an easier approach for the
+   time being.
+
+*/
+
+#if !defined (__SSP_H__)
+#    define   __SSP_H__
+
+/* ----- Includes */
+
+/* ----- Types */
+
+struct ssp_driver {
+	int  (*init)		(void);
+	void (*exit)		(void);
+	void (*acquire)		(void);
+	void (*release)		(void);
+	int  (*configure)	(int device, int mode, int speed,
+				 int frame_size_write, int frame_size_read);
+	void (*chip_select)	(int enable);
+	void (*set_callbacks)   (void* handle,
+				 irqreturn_t (*callback_tx)(void*),
+				 irqreturn_t (*callback_rx)(void*));
+	void (*enable)		(void);
+	void (*disable)		(void);
+//	int  (*save_state)	(void*);
+//	void (*restore_state)	(void*);
+	int  (*read)		(void);
+	int  (*write)		(u16 data);
+	int  (*write_read)	(u16 data);
+	void (*flush)		(void);
+	void (*write_async)	(void* pv, size_t cb);
+	size_t (*write_pos)	(void);
+};
+
+	/* These modes are only available on the LH79524 */
+#define SSP_MODE_SPI		(1)
+#define SSP_MODE_SSI		(2)
+#define SSP_MODE_MICROWIRE	(3)
+#define SSP_MODE_I2S		(4)
+
+	/* CPLD SPI devices */
+#define DEVICE_EEPROM	0	/* Configuration eeprom */
+#define DEVICE_MAC	1	/* MAC eeprom (LPD79524) */
+#define DEVICE_CODEC	2	/* Audio codec */
+#define DEVICE_TOUCH	3	/* Touch screen (LPD79520) */
+
+/* ----- Globals */
+
+/* ----- Prototypes */
+
+//extern struct ssp_driver lh79520_i2s_driver;
+extern struct ssp_driver lh7a400_cpld_ssp_driver;
+
+#endif  /* __SSP_H__ */
diff --git a/include/asm-arm/arch-lh7a40x/uncompress.h b/include/asm-arm/arch-lh7a40x/uncompress.h
index f805334..3d1ce04 100644
--- a/include/asm-arm/arch-lh7a40x/uncompress.h
+++ b/include/asm-arm/arch-lh7a40x/uncompress.h
@@ -16,7 +16,7 @@
 #ifndef UART_R_STATUS
 # define UART_R_STATUS	(0x10)
 #endif
-#define nTxRdy  	(0x20)	/* Not TxReady (literally Tx FIFO full) */
+#define nTxRdy		(0x20)	/* Not TxReady (literally Tx FIFO full) */
 
 	/* Access UART with physical addresses before MMU is setup */
 #define UART_STATUS (*(volatile unsigned long*) (UART2_PHYS + UART_R_STATUS))
diff --git a/include/asm-arm/arch-pnx4008/clock.h b/include/asm-arm/arch-pnx4008/clock.h
new file mode 100644
index 0000000..91ae003
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/clock.h
@@ -0,0 +1,61 @@
+/*
+ * include/asm-arm/arch-pnx4008/clock.h
+ *
+ * Clock control driver for PNX4008 - header file
+ *
+ * Authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#ifndef __PNX4008_CLOCK_H__
+#define __PNX4008_CLOCK_H__
+
+struct module;
+struct clk;
+
+#define PWRMAN_VA_BASE		IO_ADDRESS(PNX4008_PWRMAN_BASE)
+#define HCLKDIVCTRL_REG		(PWRMAN_VA_BASE + 0x40)
+#define PWRCTRL_REG		(PWRMAN_VA_BASE + 0x44)
+#define PLLCTRL_REG		(PWRMAN_VA_BASE + 0x48)
+#define OSC13CTRL_REG		(PWRMAN_VA_BASE + 0x4c)
+#define SYSCLKCTRL_REG		(PWRMAN_VA_BASE + 0x50)
+#define HCLKPLLCTRL_REG		(PWRMAN_VA_BASE + 0x58)
+#define USBCTRL_REG		(PWRMAN_VA_BASE + 0x64)
+#define SDRAMCLKCTRL_REG	(PWRMAN_VA_BASE + 0x68)
+#define MSCTRL_REG		(PWRMAN_VA_BASE + 0x80)
+#define BTCLKCTRL		(PWRMAN_VA_BASE + 0x84)
+#define DUMCLKCTRL_REG		(PWRMAN_VA_BASE + 0x90)
+#define I2CCLKCTRL_REG		(PWRMAN_VA_BASE + 0xac)
+#define KEYCLKCTRL_REG		(PWRMAN_VA_BASE + 0xb0)
+#define TSCLKCTRL_REG		(PWRMAN_VA_BASE + 0xb4)
+#define PWMCLKCTRL_REG		(PWRMAN_VA_BASE + 0xb8)
+#define SPICTRL_REG		(PWRMAN_VA_BASE + 0xc4)
+#define FLASHCLKCTRL_REG	(PWRMAN_VA_BASE + 0xc8)
+#define UART3CLK_REG		(PWRMAN_VA_BASE + 0xd0)
+#define UARTCLKCTRL_REG		(PWRMAN_VA_BASE + 0xe4)
+#define DMACLKCTRL_REG		(PWRMAN_VA_BASE + 0xe8)
+#define AUTOCLK_CTRL		(PWRMAN_VA_BASE + 0xec)
+#define JPEGCLKCTRL_REG		(PWRMAN_VA_BASE + 0xfc)
+
+#define AUDIOCONFIG_VA_BASE	IO_ADDRESS(PNX4008_AUDIOCONFIG_BASE)
+#define DSPPLLCTRL_REG		(AUDIOCONFIG_VA_BASE + 0x60)
+#define DSPCLKCTRL_REG		(AUDIOCONFIG_VA_BASE + 0x64)
+#define AUDIOCLKCTRL_REG	(AUDIOCONFIG_VA_BASE + 0x68)
+#define AUDIOPLLCTRL_REG	(AUDIOCONFIG_VA_BASE + 0x6C)
+
+#define USB_OTG_CLKCTRL_REG	IO_ADDRESS(PNX4008_USB_CONFIG_BASE + 0xff4)
+
+#define VFP9CLKCTRL_REG		IO_ADDRESS(PNX4008_DEBUG_BASE)
+
+#define CLK_RATE_13MHZ 13000
+#define CLK_RATE_1MHZ 1000
+#define CLK_RATE_208MHZ 208000
+#define CLK_RATE_48MHZ 48000
+#define CLK_RATE_32KHZ 32
+
+#define PNX4008_UART_CLK CLK_RATE_13MHZ * 1000 /* in MHz */
+
+#endif
diff --git a/include/asm-arm/arch-pnx4008/debug-macro.S b/include/asm-arm/arch-pnx4008/debug-macro.S
new file mode 100644
index 0000000..eb3839d
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/debug-macro.S
@@ -0,0 +1,27 @@
+/* linux/include/asm-arm/arch-pnx4008/debug-macro.S
+ *
+ * Debugging macro include header
+ *
+ *  Copyright (C) 1994-1999 Russell King
+ *  Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+		.macro	addruart,rx
+		mrc	p15, 0, \rx, c1, c0
+		tst	\rx, #1			@ MMU enabled?
+		mov	\rx, #0x00090000
+		addeq	\rx, \rx, #0x40000000
+		addne	\rx, \rx, #0xf4000000
+		.endm
+
+		.macro	senduart,rd,rx
+		strb	\rd, [\rx, #0x0]
+		.endm
+
+#define UART_SHIFT	2
+#include <asm/hardware/debug-8250.S>
diff --git a/include/asm-arm/arch-pnx4008/dma.h b/include/asm-arm/arch-pnx4008/dma.h
new file mode 100644
index 0000000..3aee120
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/dma.h
@@ -0,0 +1,162 @@
+/*
+ *  linux/include/asm-arm/arch-pnx4008/dma.h
+ *
+ *  PNX4008 DMA header file
+ *
+ *  Author:	Vitaly Wool
+ *  Copyright:	MontaVista Software Inc. (c) 2005
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_DMA_H
+#define __ASM_ARCH_DMA_H
+
+#include "platform.h"
+
+#define MAX_DMA_ADDRESS		0xffffffff
+
+#define MAX_DMA_CHANNELS	8
+
+#define DMAC_BASE		IO_ADDRESS(PNX4008_DMA_CONFIG_BASE)
+#define DMAC_INT_STAT		(DMAC_BASE + 0x0000)
+#define DMAC_INT_TC_STAT	(DMAC_BASE + 0x0004)
+#define DMAC_INT_TC_CLEAR	(DMAC_BASE + 0x0008)
+#define DMAC_INT_ERR_STAT	(DMAC_BASE + 0x000c)
+#define DMAC_INT_ERR_CLEAR	(DMAC_BASE + 0x0010)
+#define DMAC_SOFT_SREQ		(DMAC_BASE + 0x0024)
+#define DMAC_CONFIG		(DMAC_BASE + 0x0030)
+#define DMAC_Cx_SRC_ADDR(c)	(DMAC_BASE + 0x0100 + (c) * 0x20)
+#define DMAC_Cx_DEST_ADDR(c)	(DMAC_BASE + 0x0104 + (c) * 0x20)
+#define DMAC_Cx_LLI(c)		(DMAC_BASE + 0x0108 + (c) * 0x20)
+#define DMAC_Cx_CONTROL(c)	(DMAC_BASE + 0x010c + (c) * 0x20)
+#define DMAC_Cx_CONFIG(c)	(DMAC_BASE + 0x0110 + (c) * 0x20)
+
+enum {
+	WIDTH_BYTE = 0,
+	WIDTH_HWORD,
+	WIDTH_WORD
+};
+
+enum {
+	FC_MEM2MEM_DMA,
+	FC_MEM2PER_DMA,
+	FC_PER2MEM_DMA,
+	FC_PER2PER_DMA,
+	FC_PER2PER_DPER,
+	FC_MEM2PER_PER,
+	FC_PER2MEM_PER,
+	FC_PER2PER_SPER
+};
+
+enum {
+	DMA_INT_UNKNOWN = 0,
+	DMA_ERR_INT = 1,
+	DMA_TC_INT = 2,
+};
+
+enum {
+	DMA_BUFFER_ALLOCATED = 1,
+	DMA_HAS_LL = 2,
+};
+
+enum {
+	PER_CAM_DMA_1 = 0,
+	PER_NDF_FLASH = 1,
+	PER_MBX_SLAVE_FIFO = 2,
+	PER_SPI2_REC_XMIT = 3,
+	PER_MS_SD_RX_XMIT = 4,
+	PER_HS_UART_1_XMIT = 5,
+	PER_HS_UART_1_RX = 6,
+	PER_HS_UART_2_XMIT = 7,
+	PER_HS_UART_2_RX = 8,
+	PER_HS_UART_7_XMIT = 9,
+	PER_HS_UART_7_RX = 10,
+	PER_SPI1_REC_XMIT = 11,
+	PER_MLC_NDF_SREC = 12,
+	PER_CAM_DMA_2 = 13,
+	PER_PRNG_INFIFO = 14,
+	PER_PRNG_OUTFIFO = 15,
+};
+
+struct pnx4008_dma_ch_ctrl {
+	int tc_mask;
+	int cacheable;
+	int bufferable;
+	int priv_mode;
+	int di;
+	int si;
+	int dest_ahb1;
+	int src_ahb1;
+	int dwidth;
+	int swidth;
+	int dbsize;
+	int sbsize;
+	int tr_size;
+};
+
+struct pnx4008_dma_ch_config {
+	int halt;
+	int active;
+	int lock;
+	int itc;
+	int ie;
+	int flow_cntrl;
+	int dest_per;
+	int src_per;
+};
+
+struct pnx4008_dma_ll {
+	unsigned long src_addr;
+	unsigned long dest_addr;
+	u32 next_dma;
+	unsigned long ch_ctrl;
+	struct pnx4008_dma_ll *next;
+	int flags;
+	void *alloc_data;
+	int (*free) (void *);
+};
+
+struct pnx4008_dma_config {
+	int is_ll;
+	unsigned long src_addr;
+	unsigned long dest_addr;
+	unsigned long ch_ctrl;
+	unsigned long ch_cfg;
+	struct pnx4008_dma_ll *ll;
+	u32 ll_dma;
+	int flags;
+	void *alloc_data;
+	int (*free) (void *);
+};
+
+extern struct pnx4008_dma_ll *pnx4008_alloc_ll_entry(dma_addr_t *);
+extern void pnx4008_free_ll_entry(struct pnx4008_dma_ll *, dma_addr_t);
+extern void pnx4008_free_ll(u32 ll_dma, struct pnx4008_dma_ll *);
+
+extern int pnx4008_request_channel(char *, int,
+				   void (*)(int, int, void *, struct pt_regs *),
+				   void *);
+extern void pnx4008_free_channel(int);
+extern int pnx4008_config_dma(int, int, int);
+extern int pnx4008_dma_pack_control(const struct pnx4008_dma_ch_ctrl *,
+				    unsigned long *);
+extern int pnx4008_dma_parse_control(unsigned long,
+				     struct pnx4008_dma_ch_ctrl *);
+extern int pnx4008_dma_pack_config(const struct pnx4008_dma_ch_config *,
+				   unsigned long *);
+extern int pnx4008_dma_parse_config(unsigned long,
+				    struct pnx4008_dma_ch_config *);
+extern int pnx4008_config_channel(int, struct pnx4008_dma_config *);
+extern int pnx4008_channel_get_config(int, struct pnx4008_dma_config *);
+extern int pnx4008_dma_ch_enable(int);
+extern int pnx4008_dma_ch_disable(int);
+extern int pnx4008_dma_ch_enabled(int);
+extern void pnx4008_dma_split_head_entry(struct pnx4008_dma_config *,
+					 struct pnx4008_dma_ch_ctrl *);
+extern void pnx4008_dma_split_ll_entry(struct pnx4008_dma_ll *,
+				       struct pnx4008_dma_ch_ctrl *);
+
+#endif				/* _ASM_ARCH_DMA_H */
diff --git a/include/asm-arm/arch-pnx4008/entry-macro.S b/include/asm-arm/arch-pnx4008/entry-macro.S
new file mode 100644
index 0000000..c1c198e
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/entry-macro.S
@@ -0,0 +1,121 @@
+/*
+ * include/asm-arm/arch-pnx4008/entry-macro.S
+ *
+ * Low-level IRQ helper macros for PNX4008-based platforms
+ *
+ * 2005-2006 (c) MontaVista Software, Inc.
+ * Author: Vitaly Wool <vwool@ru.mvista.com>
+ * This file is licensed under  the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include "platform.h"
+
+#define IO_BASE         0xF0000000
+#define IO_ADDRESS(x)  (((((x) & 0xff000000) >> 4) | ((x) & 0xfffff)) | IO_BASE)
+
+#define INTRC_MASK			0x00
+#define INTRC_RAW_STAT			0x04
+#define INTRC_STAT			0x08
+#define INTRC_POLAR			0x0C
+#define INTRC_ACT_TYPE			0x10
+#define INTRC_TYPE			0x14
+
+#define SIC1_BASE_INT   32
+#define SIC2_BASE_INT   64
+
+		.macro	disable_fiq
+		.endm
+
+		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
+/* decode the MIC interrupt numbers */
+		ldr	\base, =IO_ADDRESS(PNX4008_INTCTRLMIC_BASE)
+		ldr	\irqstat, [\base, #INTRC_STAT]
+
+		cmp	\irqstat,#1<<16
+		movhs	\irqnr,#16
+		movlo	\irqnr,#0
+		movhs	\irqstat,\irqstat,lsr#16
+		cmp	\irqstat,#1<<8
+		addhs	\irqnr,\irqnr,#8
+		movhs	\irqstat,\irqstat,lsr#8
+		cmp	\irqstat,#1<<4
+		addhs	\irqnr,\irqnr,#4
+		movhs	\irqstat,\irqstat,lsr#4
+		cmp	\irqstat,#1<<2
+		addhs	\irqnr,\irqnr,#2
+		movhs	\irqstat,\irqstat,lsr#2
+		cmp	\irqstat,#1<<1
+		addhs	\irqnr,\irqnr,#1
+
+/* was there an interrupt ? if not then drop out with EQ status */
+		teq	\irqstat,#0
+		beq	1003f
+
+/* and now check for extended IRQ reasons */
+		cmp	\irqnr,#1
+		bls	1003f
+		cmp	\irqnr,#30
+		blo	1002f
+
+/* IRQ 31,30  : High priority cascade IRQ handle */
+/* read the correct SIC */
+/* decoding status after compare : eq is 30 (SIC1) , ne is 31 (SIC2) */
+/* set the base IRQ number */
+		ldreq	\base, =IO_ADDRESS(PNX4008_INTCTRLSIC1_BASE)
+		moveq  \irqnr,#SIC1_BASE_INT
+		ldrne	\base, =IO_ADDRESS(PNX4008_INTCTRLSIC2_BASE)
+		movne   \irqnr,#SIC2_BASE_INT
+		ldr	\irqstat, [\base, #INTRC_STAT]
+		ldr	\tmp,	  [\base, #INTRC_TYPE]
+/* and with inverted mask : low priority interrupts  */
+		and	\irqstat,\irqstat,\tmp
+		b	1004f
+
+1003:
+/* IRQ 1,0  : Low priority cascade IRQ handle */
+/* read the correct SIC */
+/* decoding status after compare : eq is 1 (SIC2) , ne is 0 (SIC1)*/
+/* read the correct SIC */
+/* set the base IRQ number  */
+		ldrne	\base, =IO_ADDRESS(PNX4008_INTCTRLSIC1_BASE)
+		movne   \irqnr,#SIC1_BASE_INT
+		ldreq	\base, =IO_ADDRESS(PNX4008_INTCTRLSIC2_BASE)
+		moveq   \irqnr,#SIC2_BASE_INT
+		ldr	\irqstat, [\base, #INTRC_STAT]
+		ldr	\tmp,	  [\base, #INTRC_TYPE]
+/* and with inverted mask : low priority interrupts  */
+		bic	\irqstat,\irqstat,\tmp
+
+1004:
+
+		cmp	\irqstat,#1<<16
+		addhs	\irqnr,\irqnr,#16
+		movhs	\irqstat,\irqstat,lsr#16
+		cmp	\irqstat,#1<<8
+		addhs	\irqnr,\irqnr,#8
+		movhs	\irqstat,\irqstat,lsr#8
+		cmp	\irqstat,#1<<4
+		addhs	\irqnr,\irqnr,#4
+		movhs	\irqstat,\irqstat,lsr#4
+		cmp	\irqstat,#1<<2
+		addhs	\irqnr,\irqnr,#2
+		movhs	\irqstat,\irqstat,lsr#2
+		cmp	\irqstat,#1<<1
+		addhs	\irqnr,\irqnr,#1
+
+
+/* is irqstat not zero */
+
+1002:
+/* we assert that irqstat is not equal to zero and return ne status if true*/
+		teq	\irqstat,#0
+1003:
+		.endm
+
+
+		.macro	irq_prio_table
+		.endm
+
+
diff --git a/include/asm-arm/arch-pnx4008/gpio.h b/include/asm-arm/arch-pnx4008/gpio.h
new file mode 100644
index 0000000..1fa5a77
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/gpio.h
@@ -0,0 +1,139 @@
+/*
+ * include/asm-arm/arch-pnx4008/gpio.h
+ *
+ * PNX4008 GPIO driver - header file
+ *
+ * Author: Dmitry Chigirev <source@mvista.com>
+ *
+ * Based on reference code by Iwo Mergler and Z.Tabaaloute from Philips:
+ * Copyright (c) 2005 Koninklijke Philips Electronics N.V.
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#ifndef _PNX4008_GPIO_H_
+#define _PNX4008_GPIO_H_
+
+
+/* Block numbers */
+#define GPIO_IN		(0)
+#define GPIO_OUT		(0x100)
+#define GPIO_BID		(0x200)
+#define GPIO_RAM		(0x300)
+#define GPIO_MUX		(0x400)
+
+#define GPIO_TYPE_MASK(K) ((K) & 0x700)
+
+/* INPUT GPIOs */
+/* GPI */
+#define GPI_00		(GPIO_IN | 0)
+#define GPI_01		(GPIO_IN | 1)
+#define GPI_02   	(GPIO_IN | 2)
+#define GPI_03 	 	(GPIO_IN | 3)
+#define GPI_04   	(GPIO_IN | 4)
+#define GPI_05   	(GPIO_IN | 5)
+#define GPI_06   	(GPIO_IN | 6)
+#define GPI_07   	(GPIO_IN | 7)
+#define GPI_08   	(GPIO_IN | 8)
+#define GPI_09   	(GPIO_IN | 9)
+#define U1_RX 		(GPIO_IN | 15)
+#define U2_HTCS 	(GPIO_IN | 16)
+#define U2_RX	 	(GPIO_IN | 17)
+#define U3_RX		(GPIO_IN | 18)
+#define U4_RX		(GPIO_IN | 19)
+#define U5_RX		(GPIO_IN | 20)
+#define U6_IRRX 	(GPIO_IN | 21)
+#define U7_HCTS 	(GPIO_IN | 22)
+#define U7_RX		(GPIO_IN | 23)
+/* MISC IN */
+#define SPI1_DATIN	(GPIO_IN | 25)
+#define DISP_SYNC	(GPIO_IN | 26)
+#define SPI2_DATIN	(GPIO_IN | 27)
+#define GPI_11  	(GPIO_IN | 28)
+
+#define GPIO_IN_MASK   0x1eff83ff
+
+/* OUTPUT GPIOs */
+/* GPO */
+#define GPO_00		(GPIO_OUT | 0)
+#define GPO_01   	(GPIO_OUT | 1)
+#define GPO_02   	(GPIO_OUT | 2)
+#define GPO_03 	 	(GPIO_OUT | 3)
+#define GPO_04   	(GPIO_OUT | 4)
+#define GPO_05   	(GPIO_OUT | 5)
+#define GPO_06   	(GPIO_OUT | 6)
+#define GPO_07   	(GPIO_OUT | 7)
+#define GPO_08		(GPIO_OUT | 8)
+#define GPO_09   	(GPIO_OUT | 9)
+#define GPO_10   	(GPIO_OUT | 10)
+#define GPO_11 	 	(GPIO_OUT | 11)
+#define GPO_12   	(GPIO_OUT | 12)
+#define GPO_13   	(GPIO_OUT | 13)
+#define GPO_14   	(GPIO_OUT | 14)
+#define GPO_15   	(GPIO_OUT | 15)
+#define GPO_16  	(GPIO_OUT | 16)
+#define GPO_17 	 	(GPIO_OUT | 17)
+#define GPO_18   	(GPIO_OUT | 18)
+#define GPO_19   	(GPIO_OUT | 19)
+#define GPO_20   	(GPIO_OUT | 20)
+#define GPO_21   	(GPIO_OUT | 21)
+#define GPO_22   	(GPIO_OUT | 22)
+#define GPO_23   	(GPIO_OUT | 23)
+
+#define GPIO_OUT_MASK   0xffffff
+
+/* BIDIRECTIONAL GPIOs */
+/* RAM pins */
+#define RAM_D19		(GPIO_RAM | 0)
+#define RAM_D20  	(GPIO_RAM | 1)
+#define RAM_D21  	(GPIO_RAM | 2)
+#define RAM_D22 	(GPIO_RAM | 3)
+#define RAM_D23  	(GPIO_RAM | 4)
+#define RAM_D24  	(GPIO_RAM | 5)
+#define RAM_D25  	(GPIO_RAM | 6)
+#define RAM_D26  	(GPIO_RAM | 7)
+#define RAM_D27		(GPIO_RAM | 8)
+#define RAM_D28  	(GPIO_RAM | 9)
+#define RAM_D29  	(GPIO_RAM | 10)
+#define RAM_D30 	(GPIO_RAM | 11)
+#define RAM_D31  	(GPIO_RAM | 12)
+
+#define GPIO_RAM_MASK   0x1fff
+
+/* I/O pins */
+#define GPIO_00  	(GPIO_BID | 25)
+#define GPIO_01 	(GPIO_BID | 26)
+#define GPIO_02  	(GPIO_BID | 27)
+#define GPIO_03  	(GPIO_BID | 28)
+#define GPIO_04 	(GPIO_BID | 29)
+#define GPIO_05  	(GPIO_BID | 30)
+
+#define GPIO_BID_MASK   0x7e000000
+
+/* Non-GPIO multiplexed PIOs. For multiplexing with GPIO, please use GPIO macros */
+#define GPIO_SDRAM_SEL 	(GPIO_MUX | 3)
+
+#define GPIO_MUX_MASK   0x8
+
+/* Extraction/assembly macros */
+#define GPIO_BIT_MASK(K) ((K) & 0x1F)
+#define GPIO_BIT(K) (1 << GPIO_BIT_MASK(K))
+#define GPIO_ISMUX(K) ((GPIO_TYPE_MASK(K) == GPIO_MUX) && (GPIO_BIT(K) & GPIO_MUX_MASK))
+#define GPIO_ISRAM(K) ((GPIO_TYPE_MASK(K) == GPIO_RAM) && (GPIO_BIT(K) & GPIO_RAM_MASK))
+#define GPIO_ISBID(K) ((GPIO_TYPE_MASK(K) == GPIO_BID) && (GPIO_BIT(K) & GPIO_BID_MASK))
+#define GPIO_ISOUT(K) ((GPIO_TYPE_MASK(K) == GPIO_OUT) && (GPIO_BIT(K) & GPIO_OUT_MASK))
+#define GPIO_ISIN(K)  ((GPIO_TYPE_MASK(K) == GPIO_IN) && (GPIO_BIT(K) & GPIO_IN_MASK))
+
+extern int pnx4008_gpio_register_pin(unsigned short pin);
+extern int pnx4008_gpio_unregister_pin(unsigned short pin);
+extern unsigned long pnx4008_gpio_read_pin(unsigned short pin);
+extern int pnx4008_gpio_write_pin(unsigned short pin, int output);
+extern int pnx4008_gpio_set_pin_direction(unsigned short pin, int output);
+extern int pnx4008_gpio_read_pin_direction(unsigned short pin);
+extern int pnx4008_gpio_set_pin_mux(unsigned short pin, int output);
+extern int pnx4008_gpio_read_pin_mux(unsigned short pin);
+
+#endif				/* _PNX4008_GPIO_H_ */
diff --git a/include/asm-arm/arch-pnx4008/hardware.h b/include/asm-arm/arch-pnx4008/hardware.h
new file mode 100644
index 0000000..a441039
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/hardware.h
@@ -0,0 +1,32 @@
+/*
+ * linux/include/asm-arm/arch-pnx4008/hardware.h
+ *
+ * Copyright (c) 2005 MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef __ASM_ARCH_HARDWARE_H
+#define __ASM_ARCH_HARDWARE_H
+
+#include <asm/sizes.h>
+#include <asm/arch/platform.h>
+
+/* Start of virtual addresses for IO devices */
+#define IO_BASE         0xF0000000
+
+/* This macro relies on fact that for all HW i/o addresses bits 20-23 are 0 */
+#define IO_ADDRESS(x)  (((((x) & 0xff000000) >> 4) | ((x) & 0xfffff)) | IO_BASE)
+
+#endif
diff --git a/include/asm-arm/arch-pnx4008/io.h b/include/asm-arm/arch-pnx4008/io.h
new file mode 100644
index 0000000..29ee439
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/io.h
@@ -0,0 +1,21 @@
+
+/*
+ *  include/asm-arm/arch-pnx4008/io.h
+ *
+ * Author: Dmitry Chigirev <chigirev@ru.mvista.com>
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#ifndef __ASM_ARM_ARCH_IO_H
+#define __ASM_ARM_ARCH_IO_H
+
+#define IO_SPACE_LIMIT 0xffffffff
+
+#define __io(a)			((void __iomem *)(a))
+#define __mem_pci(a)		(a)
+
+#endif
diff --git a/include/asm-arm/arch-pnx4008/irq.h b/include/asm-arm/arch-pnx4008/irq.h
new file mode 100644
index 0000000..fabff5d
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/irq.h
@@ -0,0 +1,42 @@
+/*
+ * include/asm-arm/arch-pnx4008/irq.h
+ *
+ * PNX4008 IRQ controller driver - header file
+ * this one is used in entry-arnv.S as well so it cannot contain C code
+ *
+ * Copyright (c) 2005 Philips Semiconductors
+ * Copyright (c) 2005 MontaVista Software, Inc.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ */
+#ifndef __PNX4008_IRQ_H__
+#define __PNX4008_IRQ_H__
+
+#define MIC_VA_BASE             IO_ADDRESS(PNX4008_INTCTRLMIC_BASE)
+#define SIC1_VA_BASE            IO_ADDRESS(PNX4008_INTCTRLSIC1_BASE)
+#define SIC2_VA_BASE            IO_ADDRESS(PNX4008_INTCTRLSIC2_BASE)
+
+/* Manual: Chapter 20, page 195 */
+
+#define INTC_BIT(irq) (1<< ((irq) & 0x1F))
+
+#define INTC_ER(irq)    IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x0 + (((irq)&(0x3<<5))<<9)))
+#define INTC_RSR(irq)   IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x4 + (((irq)&(0x3<<5))<<9)))
+#define INTC_SR(irq)    IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x8 + (((irq)&(0x3<<5))<<9)))
+#define INTC_APR(irq)   IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0xC + (((irq)&(0x3<<5))<<9)))
+#define INTC_ATR(irq)   IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x10 + (((irq)&(0x3<<5))<<9)))
+#define INTC_ITR(irq)   IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x14 + (((irq)&(0x3<<5))<<9)))
+
+#define START_INT_REG_BIT(irq) (1<<((irq)&0x1F))
+
+#define START_INT_ER_REG(irq)     IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x20 + (((irq)&(0x1<<5))>>1)))
+#define START_INT_RSR_REG(irq)    IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x24 + (((irq)&(0x1<<5))>>1)))
+#define START_INT_SR_REG(irq)     IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x28 + (((irq)&(0x1<<5))>>1)))
+#define START_INT_APR_REG(irq)    IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x2C + (((irq)&(0x1<<5))>>1)))
+
+extern void __init pnx4008_init_irq(void);
+
+#endif /* __PNX4008_IRQ_H__ */
diff --git a/include/asm-arm/arch-pnx4008/irqs.h b/include/asm-arm/arch-pnx4008/irqs.h
new file mode 100644
index 0000000..13ec7ed
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/irqs.h
@@ -0,0 +1,215 @@
+/*
+ * include/asm-arm/arch-pnx4008/irqs.h
+ *
+ * PNX4008 IRQ controller driver - header file
+ *
+ * Author: Dmitry Chigirev <source@mvista.com>
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#ifndef __PNX4008_IRQS_h__
+#define __PNX4008_IRQS_h__
+
+#define NR_IRQS         96
+
+/*Manual: table 259, page 199*/
+
+/*SUB2 Interrupt Routing (SIC2)*/
+
+#define SIC2_BASE_INT   64
+
+#define CLK_SWITCH_ARM_INT 95	/*manual: Clkswitch ARM  */
+#define CLK_SWITCH_DSP_INT 94	/*manual: ClkSwitch DSP  */
+#define CLK_SWITCH_AUD_INT 93	/*manual: Clkswitch AUD  */
+#define GPI_06_INT         92
+#define GPI_05_INT         91
+#define GPI_04_INT         90
+#define GPI_03_INT         89
+#define GPI_02_INT         88
+#define GPI_01_INT         87
+#define GPI_00_INT         86
+#define BT_CLKREQ_INT      85
+#define SPI1_DATIN_INT     84
+#define U5_RX_INT          83
+#define SDIO_INT_N         82
+#define CAM_HS_INT         81
+#define CAM_VS_INT         80
+#define GPI_07_INT         79
+#define DISP_SYNC_INT      78
+#define DSP_INT8           77
+#define U7_HCTS_INT        76
+#define GPI_10_INT         75
+#define GPI_09_INT         74
+#define GPI_08_INT         73
+#define DSP_INT7           72
+#define U2_HCTS_INT        71
+#define SPI2_DATIN_INT     70
+#define GPIO_05_INT        69
+#define GPIO_04_INT        68
+#define GPIO_03_INT        67
+#define GPIO_02_INT        66
+#define GPIO_01_INT        65
+#define GPIO_00_INT        64
+
+/*Manual: table 258, page 198*/
+
+/*SUB1 Interrupt Routing (SIC1)*/
+
+#define SIC1_BASE_INT   32
+
+#define USB_I2C_INT        63
+#define USB_DEV_HP_INT     62
+#define USB_DEV_LP_INT     61
+#define USB_DEV_DMA_INT    60
+#define USB_HOST_INT       59
+#define USB_OTG_ATX_INT_N  58
+#define USB_OTG_TIMER_INT  57
+#define SW_INT             56
+#define SPI1_INT           55
+#define KEY_IRQ            54
+#define DSP_M_INT          53
+#define RTC_INT            52
+#define I2C_1_INT          51
+#define I2C_2_INT          50
+#define PLL1_LOCK_INT      49
+#define PLL2_LOCK_INT      48
+#define PLL3_LOCK_INT      47
+#define PLL4_LOCK_INT      46
+#define PLL5_LOCK_INT      45
+#define SPI2_INT           44
+#define DSP_INT1           43
+#define DSP_INT2           42
+#define DSP_TDM_INT2       41
+#define TS_AUX_INT         40
+#define TS_IRQ             39
+#define TS_P_INT           38
+#define UOUT1_TO_PAD_INT   37
+#define GPI_11_INT         36
+#define DSP_INT4           35
+#define JTAG_COMM_RX_INT   34
+#define JTAG_COMM_TX_INT   33
+#define DSP_INT3           32
+
+/*Manual: table 257, page 197*/
+
+/*MAIN Interrupt Routing*/
+
+#define MAIN_BASE_INT   0
+
+#define SUB2_FIQ_N         31	/*active low */
+#define SUB1_FIQ_N         30	/*active low */
+#define JPEG_INT           29
+#define DMA_INT            28
+#define MSTIMER_INT        27
+#define IIR1_INT           26
+#define IIR2_INT           25
+#define IIR7_INT           24
+#define DSP_TDM_INT0       23
+#define DSP_TDM_INT1       22
+#define DSP_P_INT          21
+#define DSP_INT0           20
+#define DUM_INT            19
+#define UOUT0_TO_PAD_INT   18
+#define MP4_ENC_INT        17
+#define MP4_DEC_INT        16
+#define SD0_INT            15
+#define MBX_INT            14
+#define SD1_INT            13
+#define MS_INT_N           12
+#define FLASH_INT          11 /*NAND*/
+#define IIR6_INT           10
+#define IIR5_INT           9
+#define IIR4_INT           8
+#define IIR3_INT           7
+#define WATCH_INT          6
+#define HSTIMER_INT        5
+#define ARCH_TIMER_IRQ     HSTIMER_INT
+#define CAM_INT            4
+#define PRNG_INT           3
+#define CRYPTO_INT         2
+#define SUB2_IRQ_N         1	/*active low */
+#define SUB1_IRQ_N         0	/*active low */
+
+#define PNX4008_IRQ_TYPES \
+{                                           /*IRQ #'s: */         \
+IRQT_LOW,  IRQT_LOW,  IRQT_LOW,  IRQT_HIGH, /*  0, 1, 2, 3 */     \
+IRQT_LOW,  IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /*  4, 5, 6, 7 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /*  8, 9,10,11 */     \
+IRQT_LOW,  IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 12,13,14,15 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 16,17,18,19 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 20,21,22,23 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 24,25,26,27 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_LOW,  IRQT_LOW,  /* 28,29,30,31 */     \
+IRQT_HIGH, IRQT_LOW,  IRQT_HIGH, IRQT_HIGH, /* 32,33,34,35 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_FALLING, IRQT_HIGH, /* 36,37,38,39 */  \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 40,41,42,43 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 44,45,46,47 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_LOW,  IRQT_LOW,  /* 48,49,50,51 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 52,53,54,55 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_LOW,  IRQT_HIGH, /* 56,57,58,59 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 60,61,62,63 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 64,65,66,67 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 68,69,70,71 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 72,73,74,75 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 76,77,78,79 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 80,81,82,83 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 84,85,86,87 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 88,89,90,91 */     \
+IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 92,93,94,95 */     \
+}
+
+/* Start Enable Pin Interrupts - table 58 page 66 */
+
+#define SE_PIN_BASE_INT   32
+
+#define SE_U7_RX_INT            63
+#define SE_U7_HCTS_INT          62
+#define SE_BT_CLKREQ_INT        61
+#define SE_U6_IRRX_INT          60
+/*59 unused*/
+#define SE_U5_RX_INT            58
+#define SE_GPI_11_INT           57
+#define SE_U3_RX_INT            56
+#define SE_U2_HCTS_INT          55
+#define SE_U2_RX_INT            54
+#define SE_U1_RX_INT            53
+#define SE_DISP_SYNC_INT        52
+/*51 unused*/
+#define SE_SDIO_INT_N           50
+#define SE_MSDIO_START_INT      49
+#define SE_GPI_06_INT           48
+#define SE_GPI_05_INT           47
+#define SE_GPI_04_INT           46
+#define SE_GPI_03_INT           45
+#define SE_GPI_02_INT           44
+#define SE_GPI_01_INT           43
+#define SE_GPI_00_INT           42
+#define SE_SYSCLKEN_PIN_INT     41
+#define SE_SPI1_DATAIN_INT      40
+#define SE_GPI_07_INT           39
+#define SE_SPI2_DATAIN_INT      38
+#define SE_GPI_10_INT           37
+#define SE_GPI_09_INT           36
+#define SE_GPI_08_INT           35
+/*34-32 unused*/
+
+/* Start Enable Internal Interrupts - table 57 page 65 */
+
+#define SE_INT_BASE_INT   0
+
+#define SE_TS_IRQ               31
+#define SE_TS_P_INT             30
+#define SE_TS_AUX_INT           29
+/*27-28 unused*/
+#define SE_USB_AHB_NEED_CLK_INT 26
+#define SE_MSTIMER_INT          25
+#define SE_RTC_INT              24
+#define SE_USB_NEED_CLK_INT     23
+#define SE_USB_INT              22
+#define SE_USB_I2C_INT          21
+#define SE_USB_OTG_TIMER_INT    20
+
+#endif /* __PNX4008_IRQS_h__ */
diff --git a/include/asm-arm/arch-pnx4008/memory.h b/include/asm-arm/arch-pnx4008/memory.h
new file mode 100644
index 0000000..0d8268a
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/memory.h
@@ -0,0 +1,24 @@
+/*
+ * linux/include/asm-arm/arch-pnx4008/memory.h
+ *
+ * Copyright (c) 2005 Philips Semiconductors
+ * Copyright (c) 2005 MontaVista Software, Inc.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ */
+
+#ifndef __ASM_ARCH_MEMORY_H
+#define __ASM_ARCH_MEMORY_H
+
+/*
+ * Physical DRAM offset.
+ */
+#define PHYS_OFFSET     (0x80000000)
+
+#define __virt_to_bus(x) ((x) - PAGE_OFFSET + PHYS_OFFSET)
+#define __bus_to_virt(x) ((x) + PAGE_OFFSET - PHYS_OFFSET)
+
+#endif
diff --git a/include/asm-arm/arch-pnx4008/param.h b/include/asm-arm/arch-pnx4008/param.h
new file mode 100644
index 0000000..95d5f54
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/param.h
@@ -0,0 +1,21 @@
+/*
+ *  linux/include/asm-arm/arch-pnx4008/param.h
+ *
+ *  Copyright (C) 1999 ARM Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#define HZ 100
diff --git a/include/asm-arm/arch-pnx4008/platform.h b/include/asm-arm/arch-pnx4008/platform.h
new file mode 100644
index 0000000..485a365
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/platform.h
@@ -0,0 +1,69 @@
+/*
+ * include/asm-arm/arch-pnx4008/platfrom.h
+ *
+ * PNX4008 Base addresses - header file
+ *
+ * Author: Dmitry Chigirev <source@mvista.com>
+ *
+ * Based on reference code received from Philips:
+ * Copyright (C) 2003 Philips Semiconductors
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+
+#ifndef __ASM_ARCH_PLATFORM_H__
+#define __ASM_ARCH_PLATFORM_H__
+
+#define PNX4008_IRAM_BASE		0x08000000
+#define PNX4008_IRAM_SIZE		0x00010000
+#define PNX4008_YUV_SLAVE_BASE		0x10000000
+#define PNX4008_DUM_SLAVE_BASE		0x18000000
+#define PNX4008_NDF_FLASH_BASE		0x20020000
+#define PNX4008_SPI1_BASE		0x20088000
+#define PNX4008_SPI2_BASE		0x20090000
+#define PNX4008_SD_CONFIG_BASE		0x20098000
+#define PNX4008_FLASH_DATA		0x200B0000
+#define PNX4008_MLC_FLASH_BASE		0x200B8000
+#define PNX4008_JPEG_CONFIG_BASE	0x300A0000
+#define PNX4008_DMA_CONFIG_BASE		0x31000000
+#define PNX4008_USB_CONFIG_BASE		0x31020000
+#define PNX4008_SDRAM_CFG_BASE		0x31080000
+#define PNX4008_AHB2FAB_BASE		0x40000000
+#define PNX4008_PWRMAN_BASE		0x40004000
+#define PNX4008_INTCTRLMIC_BASE		0x40008000
+#define PNX4008_INTCTRLSIC1_BASE	0x4000C000
+#define PNX4008_INTCTRLSIC2_BASE	0x40010000
+#define PNX4008_HSUART1_BASE		0x40014000
+#define PNX4008_HSUART2_BASE		0x40018000
+#define PNX4008_HSUART7_BASE		0x4001C000
+#define PNX4008_RTC_BASE		0x40024000
+#define PNX4008_PIO_BASE		0x40028000
+#define PNX4008_MSTIMER_BASE		0x40034000
+#define PNX4008_HSTIMER_BASE		0x40038000
+#define PNX4008_WDOG_BASE		0x4003C000
+#define PNX4008_DEBUG_BASE		0x40040000
+#define PNX4008_TOUCH1_BASE		0x40048000
+#define PNX4008_KEYSCAN_BASE		0x40050000
+#define PNX4008_UARTCTRL_BASE		0x40054000
+#define PNX4008_PWM_BASE		0x4005C000
+#define PNX4008_UART3_BASE		0x40080000
+#define PNX4008_UART4_BASE		0x40088000
+#define PNX4008_UART5_BASE		0x40090000
+#define PNX4008_UART6_BASE		0x40098000
+#define PNX4008_I2C1_BASE		0x400A0000
+#define PNX4008_I2C2_BASE		0x400A8000
+#define PNX4008_MAGICGATE_BASE		0x400B0000
+#define PNX4008_DUMCONF_BASE		0x400B8000
+#define PNX4008_DUM_MAINCFG_BASE       	0x400BC000
+#define PNX4008_DSP_BASE		0x400C0000
+#define PNX4008_PROFCOUNTER_BASE	0x400C8000
+#define PNX4008_CRYPTO_BASE		0x400D0000
+#define PNX4008_CAMIFCONF_BASE		0x400D8000
+#define PNX4008_YUV2RGB_BASE		0x400E0000
+#define PNX4008_AUDIOCONFIG_BASE	0x400E8000
+
+#endif
diff --git a/include/asm-arm/arch-pnx4008/pm.h b/include/asm-arm/arch-pnx4008/pm.h
new file mode 100644
index 0000000..c660486
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/pm.h
@@ -0,0 +1,62 @@
+/*
+ * include/asm-arm/arch-pnx4008/pm.h
+ *
+ * PNX4008 Power Management Routiness - header file
+ *
+ * Authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#ifndef __ASM_ARCH_PNX4008_PM_H
+#define __ASM_ARCH_PNX4008_PM_H
+
+#ifndef __ASSEMBLER__
+#include "irq.h"
+#include "irqs.h"
+#include "clock.h"
+
+extern void pnx4008_pm_idle(void);
+extern void pnx4008_pm_suspend(void);
+extern unsigned int pnx4008_cpu_suspend_sz;
+extern void pnx4008_cpu_suspend(void);
+extern unsigned int pnx4008_cpu_standby_sz;
+extern void pnx4008_cpu_standby(void);
+
+extern int pnx4008_startup_pll(struct clk *);
+extern int pnx4008_shutdown_pll(struct clk *);
+
+static inline void start_int_umask(u8 irq)
+{
+	__raw_writel(__raw_readl(START_INT_ER_REG(irq)) |
+		     START_INT_REG_BIT(irq), START_INT_ER_REG(irq));
+}
+
+static inline void start_int_mask(u8 irq)
+{
+	__raw_writel(__raw_readl(START_INT_ER_REG(irq)) &
+		     ~START_INT_REG_BIT(irq), START_INT_ER_REG(irq));
+}
+
+static inline void start_int_ack(u8 irq)
+{
+	__raw_writel(START_INT_REG_BIT(irq), START_INT_RSR_REG(irq));
+}
+
+static inline void start_int_set_falling_edge(u8 irq)
+{
+	__raw_writel(__raw_readl(START_INT_APR_REG(irq)) &
+		     ~START_INT_REG_BIT(irq), START_INT_APR_REG(irq));
+}
+
+static inline void start_int_set_rising_edge(u8 irq)
+{
+	__raw_writel(__raw_readl(START_INT_APR_REG(irq)) |
+		     START_INT_REG_BIT(irq), START_INT_APR_REG(irq));
+}
+
+#endif				/* ASSEMBLER */
+#endif				/* __ASM_ARCH_PNX4008_PM_H */
diff --git a/include/asm-arm/arch-pnx4008/system.h b/include/asm-arm/arch-pnx4008/system.h
new file mode 100644
index 0000000..6e3da70
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/system.h
@@ -0,0 +1,38 @@
+/*
+ * linux/include/asm-arm/arch-pnx4008/system.h
+ *
+ * Copyright (C) 2003 Philips Semiconductors
+ * Copyright (C) 2005 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef __ASM_ARCH_SYSTEM_H
+#define __ASM_ARCH_SYSTEM_H
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/arch/platform.h>
+
+static void arch_idle(void)
+{
+	cpu_do_idle();
+}
+
+static inline void arch_reset(char mode)
+{
+	cpu_reset(0);
+}
+
+#endif
diff --git a/include/asm-arm/arch-pnx4008/timex.h b/include/asm-arm/arch-pnx4008/timex.h
new file mode 100644
index 0000000..ee470a3
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/timex.h
@@ -0,0 +1,73 @@
+/*
+ * include/asm-arm/arch-pnx4008/timex.h
+ *
+ * PNX4008 timers header file
+ *
+ * Author: Dmitry Chigirev <source@mvista.com>
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#ifndef __PNX4008_TIMEX_H
+#define __PNX4008_TIMEX_H
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+
+#define CLOCK_TICK_RATE		1000000
+
+#define TICKS2USECS(x)	(x)
+
+/* MilliSecond Timer - Chapter 21 Page 202 */
+
+#define MSTIM_INT     IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x0))
+#define MSTIM_CTRL    IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x4))
+#define MSTIM_COUNTER IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x8))
+#define MSTIM_MCTRL   IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x14))
+#define MSTIM_MATCH0  IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x18))
+#define MSTIM_MATCH1  IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x1c))
+
+/* High Speed Timer - Chpater 22, Page 205 */
+
+#define HSTIM_INT     IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x0))
+#define HSTIM_CTRL    IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x4))
+#define HSTIM_COUNTER IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x8))
+#define HSTIM_PMATCH  IO_ADDRESS((PNX4008_HSTIMER_BASE + 0xC))
+#define HSTIM_PCOUNT  IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x10))
+#define HSTIM_MCTRL   IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x14))
+#define HSTIM_MATCH0  IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x18))
+#define HSTIM_MATCH1  IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x1c))
+#define HSTIM_MATCH2  IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x20))
+#define HSTIM_CCR     IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x28))
+#define HSTIM_CR0     IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x2C))
+#define HSTIM_CR1     IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x30))
+
+/* IMPORTANT: both timers are UPCOUNTING */
+
+/* xSTIM_MCTRL bit definitions */
+#define MR0_INT        1
+#define RESET_COUNT0   (1<<1)
+#define STOP_COUNT0    (1<<2)
+#define MR1_INT        (1<<3)
+#define RESET_COUNT1   (1<<4)
+#define STOP_COUNT1    (1<<5)
+#define MR2_INT        (1<<6)
+#define RESET_COUNT2   (1<<7)
+#define STOP_COUNT2    (1<<8)
+
+/* xSTIM_CTRL bit definitions */
+#define COUNT_ENAB     1
+#define RESET_COUNT    (1<<1)
+#define DEBUG_EN       (1<<2)
+
+/* xSTIM_INT bit definitions */
+#define MATCH0_INT     1
+#define MATCH1_INT     (1<<1)
+#define MATCH2_INT     (1<<2)
+#define RTC_TICK0      (1<<4)
+#define RTC_TICK1      (1<<5)
+
+#endif
diff --git a/include/asm-arm/arch-pnx4008/uncompress.h b/include/asm-arm/arch-pnx4008/uncompress.h
new file mode 100644
index 0000000..8fa4d24
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/uncompress.h
@@ -0,0 +1,46 @@
+/*
+ *  linux/include/asm-arm/arch-pnx4008/uncompress.h
+ *
+ *  Copyright (C) 1999 ARM Limited
+ *  Copyright (C) 2006 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#define UART5_BASE 0x40090000
+
+#define UART5_DR    (*(volatile unsigned char *) (UART5_BASE))
+#define UART5_FR    (*(volatile unsigned char *) (UART5_BASE + 18))
+
+static __inline__ void putc(char c)
+{
+	while (UART5_FR & (1 << 5))
+		barrier();
+
+	UART5_DR = c;
+}
+
+/*
+ * This does not append a newline
+ */
+static inline void flush(void)
+{
+}
+
+/*
+ * nothing to do
+ */
+#define arch_decomp_setup()
+#define arch_decomp_wdog()
diff --git a/include/asm-arm/arch-pnx4008/vmalloc.h b/include/asm-arm/arch-pnx4008/vmalloc.h
new file mode 100644
index 0000000..140d925
--- /dev/null
+++ b/include/asm-arm/arch-pnx4008/vmalloc.h
@@ -0,0 +1,20 @@
+/*
+ * include/asm-arm/arch-pnx4008/vmalloc.h
+ *
+ * Author: Vitaly Wool <source@mvista.com>
+ *
+ * 2006 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+/*
+ * Just any arbitrary offset to the start of the vmalloc VM area: the
+ * current 8MB value just means that there will be a 8MB "hole" after the
+ * physical memory until the kernel virtual memory starts.  That means that
+ * any out-of-bounds memory accesses will hopefully be caught.
+ * The vmalloc() routines leaves a hole of 4kB between each vmalloced
+ * area for the same reason. ;)
+ */
+#define VMALLOC_END       (PAGE_OFFSET + 0x10000000)
diff --git a/include/asm-arm/arch-s3c2410/map.h b/include/asm-arm/arch-s3c2410/map.h
index c380d26..5e4c8c3 100644
--- a/include/asm-arm/arch-s3c2410/map.h
+++ b/include/asm-arm/arch-s3c2410/map.h
@@ -126,9 +126,18 @@
 #define S3C24XX_SZ_IIS	   SZ_1M
 
 /* GPIO ports */
-#define S3C24XX_VA_GPIO	   S3C2410_ADDR(0x00E00000)
+
+/* the calculation for the VA of this must ensure that
+ * it is the same distance apart from the UART in the
+ * phsyical address space, as the initial mapping for the IO
+ * is done as a 1:1 maping. This puts it (currently) at
+ * 0xF6800000, which is not in the way of any current mapping
+ * by the base system.
+*/
+
 #define S3C2400_PA_GPIO	   (0x15600000)
 #define S3C2410_PA_GPIO	   (0x56000000)
+#define S3C24XX_VA_GPIO	   ((S3C2410_PA_GPIO - S3C24XX_PA_UART) + S3C24XX_VA_UART)
 #define S3C24XX_SZ_GPIO	   SZ_1M
 
 /* RTC */
diff --git a/include/asm-arm/arch-s3c2410/regs-clock.h b/include/asm-arm/arch-s3c2410/regs-clock.h
index 3436070..6c92faf 100644
--- a/include/asm-arm/arch-s3c2410/regs-clock.h
+++ b/include/asm-arm/arch-s3c2410/regs-clock.h
@@ -114,7 +114,7 @@
 
 #endif /* __ASSEMBLY__ */
 
-#ifdef CONFIG_CPU_S3C2440
+#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442)
 
 /* extra registers */
 #define S3C2440_CAMDIVN	    S3C2410_CLKREG(0x18)
@@ -136,7 +136,9 @@
 #define S3C2440_CAMDIVN_HCLK4_HALF   (1<<9)
 #define S3C2440_CAMDIVN_DVSEN        (1<<12)
 
-#endif /* CONFIG_CPU_S3C2440 */
+#define S3C2442_CAMDIVN_CAMCLK_DIV3  (1<<5)
+
+#endif /* CONFIG_CPU_S3C2440 or CONFIG_CPU_S3C2442 */
 
 
 #endif /* __ASM_ARM_REGS_CLOCK */
diff --git a/include/asm-arm/arch-s3c2410/regs-gpio.h b/include/asm-arm/arch-s3c2410/regs-gpio.h
index d257408..5f10334 100644
--- a/include/asm-arm/arch-s3c2410/regs-gpio.h
+++ b/include/asm-arm/arch-s3c2410/regs-gpio.h
@@ -450,12 +450,14 @@
 #define S3C2410_GPD0_OUTP	(0x01 << 0)
 #define S3C2410_GPD0_VD8	(0x02 << 0)
 #define S3C2400_GPD0_VFRAME	(0x02 << 0)
+#define S3C2442_GPD0_nSPICS1	(0x03 << 0)
 
 #define S3C2410_GPD1            S3C2410_GPIONO(S3C2410_GPIO_BANKD, 1)
 #define S3C2410_GPD1_INP	(0x00 << 2)
 #define S3C2410_GPD1_OUTP	(0x01 << 2)
 #define S3C2410_GPD1_VD9	(0x02 << 2)
 #define S3C2400_GPD1_VM		(0x02 << 2)
+#define S3C2442_GPD1_SPICLK1	(0x03 << 2)
 
 #define S3C2410_GPD2            S3C2410_GPIONO(S3C2410_GPIO_BANKD, 2)
 #define S3C2410_GPD2_INP	(0x00 << 4)
@@ -858,6 +860,7 @@
 #define S3C2410_GPG12_OUTP    (0x01 << 24)
 #define S3C2410_GPG12_EINT20  (0x02 << 24)
 #define S3C2410_GPG12_XMON    (0x03 << 24)
+#define S3C2442_GPG12_nSPICS0 (0x03 << 24)
 
 #define S3C2410_GPG13         S3C2410_GPIONO(S3C2410_GPIO_BANKG, 13)
 #define S3C2410_GPG13_INP     (0x00 << 26)
@@ -943,6 +946,7 @@
 #define S3C2410_GPH9_INP      (0x00 << 18)
 #define S3C2410_GPH9_OUTP     (0x01 << 18)
 #define S3C2410_GPH9_CLKOUT0  (0x02 << 18)
+#define S3C2442_GPH9_nSPICS0  (0x03 << 18)
 
 #define S3C2410_GPH10         S3C2410_GPIONO(S3C2410_GPIO_BANKH, 10)
 #define S3C2410_GPH10_INP     (0x00 << 20)
@@ -1051,6 +1055,7 @@
 #define S3C2410_GSTATUS1_IDMASK	   (0xffff0000)
 #define S3C2410_GSTATUS1_2410	   (0x32410000)
 #define S3C2410_GSTATUS1_2440	   (0x32440000)
+#define S3C2410_GSTATUS1_2442	   (0x32440aaa)
 
 #define S3C2410_GSTATUS2_WTRESET   (1<<2)
 #define S3C2410_GSTATUS2_OFFRESET  (1<<1)
diff --git a/include/asm-arm/arch-s3c2410/uncompress.h b/include/asm-arm/arch-s3c2410/uncompress.h
index a6f6a0e..bbd9ee1 100644
--- a/include/asm-arm/arch-s3c2410/uncompress.h
+++ b/include/asm-arm/arch-s3c2410/uncompress.h
@@ -82,7 +82,8 @@
 		while (1) {
 			level = uart_rd(S3C2410_UFSTAT);
 
-			if (cpuid == S3C2410_GSTATUS1_2440) {
+			if (cpuid == S3C2410_GSTATUS1_2440 ||
+			    cpuid == S3C2410_GSTATUS1_2442) {
 				level &= S3C2440_UFSTAT_TXMASK;
 				level >>= S3C2440_UFSTAT_TXSHIFT;
 			} else {
@@ -130,7 +131,7 @@
 {
 	__raw_writel(WDOG_COUNT, S3C2410_WTDAT);
 	__raw_writel(WDOG_COUNT, S3C2410_WTCNT);
-	__raw_writel(S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV128 | S3C2410_WTCON_RSTEN | S3C2410_WTCON_PRESCALE(0x40), S3C2410_WTCON);
+	__raw_writel(S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV128 | S3C2410_WTCON_RSTEN | S3C2410_WTCON_PRESCALE(0x80), S3C2410_WTCON);
 }
 
 #else
diff --git a/include/asm-arm/mach/time.h b/include/asm-arm/mach/time.h
index 96c6db7..9f28073 100644
--- a/include/asm-arm/mach/time.h
+++ b/include/asm-arm/mach/time.h
@@ -50,6 +50,7 @@
 #define DYN_TICK_ENABLED	(1 << 1)
 
 struct dyn_tick_timer {
+	spinlock_t	lock;
 	unsigned int	state;			/* Current state */
 	int		(*enable)(void);	/* Enables dynamic tick */
 	int		(*disable)(void);	/* Disables dynamic tick */