Merge branch 's3-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio-console
Pull virtio S3 support patches from Amit Shah:
"Turns out S3 is not different from S4 for virtio devices: the device
is assumed to be reset, so the host and guest state are to be assumed
to be out of sync upon resume. We handle the S4 case with exactly the
same scenario, so just point the suspend/resume routines to the
freeze/restore ones.
Once that is done, we also use the PM API's macro to initialise the
sleep functions.
A couple of cleanups are included: there's no need for special thaw
processing in the balloon driver, so that's addressed in patches 1 and
2.
Testing: both S3 and S4 support have been tested using these patches
using a similar method used earlier during S4 patch development: a
guest is started with virtio-blk as the only disk, a virtio network
card, a virtio-serial port and a virtio balloon device. Ping from
guest to host, dd /dev/zero to a file on the disk, and IO from the
host on the virtio-serial port, all at once, while exercising S4 and
S3 (separately) were tested. They all continue to work fine after
resume. virtio balloon values too were tested by inflating and
deflating the balloon."
Pulling from Amit, since Rusty is off getting married (and presumably
shaving people).
* 's3-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio-console:
virtio-pci: switch to PM ops macro to initialise PM functions
virtio-pci: S3 support
virtio-pci: drop restore_common()
virtio: drop thaw PM operation
virtio: balloon: Allow stats update after restore from S4
diff --git a/drivers/virtio/virtio_balloon.c b/drivers/virtio/virtio_balloon.c
index 958e512..05f0a80 100644
--- a/drivers/virtio/virtio_balloon.c
+++ b/drivers/virtio/virtio_balloon.c
@@ -398,21 +398,8 @@
return 0;
}
-static int virtballoon_thaw(struct virtio_device *vdev)
-{
- return restore_common(vdev);
-}
-
static int virtballoon_restore(struct virtio_device *vdev)
{
- struct virtio_balloon *vb = vdev->priv;
-
- /*
- * If a request wasn't complete at the time of freezing, this
- * could have been set.
- */
- vb->need_stats_update = 0;
-
return restore_common(vdev);
}
#endif
@@ -434,7 +421,6 @@
#ifdef CONFIG_PM
.freeze = virtballoon_freeze,
.restore = virtballoon_restore,
- .thaw = virtballoon_thaw,
#endif
};
diff --git a/drivers/virtio/virtio_pci.c b/drivers/virtio/virtio_pci.c
index 635e1ef..2e03d41 100644
--- a/drivers/virtio/virtio_pci.c
+++ b/drivers/virtio/virtio_pci.c
@@ -720,24 +720,6 @@
}
#ifdef CONFIG_PM
-static int virtio_pci_suspend(struct device *dev)
-{
- struct pci_dev *pci_dev = to_pci_dev(dev);
-
- pci_save_state(pci_dev);
- pci_set_power_state(pci_dev, PCI_D3hot);
- return 0;
-}
-
-static int virtio_pci_resume(struct device *dev)
-{
- struct pci_dev *pci_dev = to_pci_dev(dev);
-
- pci_restore_state(pci_dev);
- pci_set_power_state(pci_dev, PCI_D0);
- return 0;
-}
-
static int virtio_pci_freeze(struct device *dev)
{
struct pci_dev *pci_dev = to_pci_dev(dev);
@@ -758,47 +740,6 @@
return ret;
}
-static int restore_common(struct device *dev)
-{
- struct pci_dev *pci_dev = to_pci_dev(dev);
- struct virtio_pci_device *vp_dev = pci_get_drvdata(pci_dev);
- int ret;
-
- ret = pci_enable_device(pci_dev);
- if (ret)
- return ret;
- pci_set_master(pci_dev);
- vp_finalize_features(&vp_dev->vdev);
-
- return ret;
-}
-
-static int virtio_pci_thaw(struct device *dev)
-{
- struct pci_dev *pci_dev = to_pci_dev(dev);
- struct virtio_pci_device *vp_dev = pci_get_drvdata(pci_dev);
- struct virtio_driver *drv;
- int ret;
-
- ret = restore_common(dev);
- if (ret)
- return ret;
-
- drv = container_of(vp_dev->vdev.dev.driver,
- struct virtio_driver, driver);
-
- if (drv && drv->thaw)
- ret = drv->thaw(&vp_dev->vdev);
- else if (drv && drv->restore)
- ret = drv->restore(&vp_dev->vdev);
-
- /* Finally, tell the device we're all set */
- if (!ret)
- vp_set_status(&vp_dev->vdev, vp_dev->saved_status);
-
- return ret;
-}
-
static int virtio_pci_restore(struct device *dev)
{
struct pci_dev *pci_dev = to_pci_dev(dev);
@@ -809,8 +750,14 @@
drv = container_of(vp_dev->vdev.dev.driver,
struct virtio_driver, driver);
- ret = restore_common(dev);
- if (!ret && drv && drv->restore)
+ ret = pci_enable_device(pci_dev);
+ if (ret)
+ return ret;
+
+ pci_set_master(pci_dev);
+ vp_finalize_features(&vp_dev->vdev);
+
+ if (drv && drv->restore)
ret = drv->restore(&vp_dev->vdev);
/* Finally, tell the device we're all set */
@@ -821,12 +768,7 @@
}
static const struct dev_pm_ops virtio_pci_pm_ops = {
- .suspend = virtio_pci_suspend,
- .resume = virtio_pci_resume,
- .freeze = virtio_pci_freeze,
- .thaw = virtio_pci_thaw,
- .restore = virtio_pci_restore,
- .poweroff = virtio_pci_suspend,
+ SET_SYSTEM_SLEEP_PM_OPS(virtio_pci_freeze, virtio_pci_restore)
};
#endif
diff --git a/include/linux/virtio.h b/include/linux/virtio.h
index d0018d2..8efd28a 100644
--- a/include/linux/virtio.h
+++ b/include/linux/virtio.h
@@ -96,7 +96,6 @@
void (*config_changed)(struct virtio_device *dev);
#ifdef CONFIG_PM
int (*freeze)(struct virtio_device *dev);
- int (*thaw)(struct virtio_device *dev);
int (*restore)(struct virtio_device *dev);
#endif
};
