diff --git a/Documentation/devicetree/bindings/hwmon/ads1015.txt b/Documentation/devicetree/bindings/hwmon/ads1015.txt
new file mode 100644
index 0000000..918a507
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/ads1015.txt
@@ -0,0 +1,73 @@
+ADS1015 (I2C)
+
+This device is a 12-bit A-D converter with 4 inputs.
+
+The inputs can be used single ended or in certain differential combinations.
+
+For configuration all possible combinations are mapped to 8 channels:
+  0: Voltage over AIN0 and AIN1.
+  1: Voltage over AIN0 and AIN3.
+  2: Voltage over AIN1 and AIN3.
+  3: Voltage over AIN2 and AIN3.
+  4: Voltage over AIN0 and GND.
+  5: Voltage over AIN1 and GND.
+  6: Voltage over AIN2 and GND.
+  7: Voltage over AIN3 and GND.
+
+Each channel can be configured individually:
+ - pga is the programmable gain amplifier (values are full scale)
+    0: +/- 6.144 V
+    1: +/- 4.096 V
+    2: +/- 2.048 V (default)
+    3: +/- 1.024 V
+    4: +/- 0.512 V
+    5: +/- 0.256 V
+ - data_rate in samples per second
+    0: 128
+    1: 250
+    2: 490
+    3: 920
+    4: 1600 (default)
+    5: 2400
+    6: 3300
+
+1) The /ads1015 node
+
+  Required properties:
+
+   - compatible : must be "ti,ads1015"
+   - reg : I2C bus address of the device
+   - #address-cells : must be <1>
+   - #size-cells : must be <0>
+
+  The node contains child nodes for each channel that the platform uses.
+
+  Example ADS1015 node:
+
+    ads1015@49 {
+	    compatible = "ti,ads1015";
+	    reg = <0x49>;
+	    #address-cells = <1>;
+	    #size-cells = <0>;
+
+	    [ child node definitions... ]
+    }
+
+2) channel nodes
+
+  Required properties:
+
+   - reg : the channel number
+
+  Optional properties:
+
+   - ti,gain : the programmable gain amplifier setting
+   - ti,datarate : the converter data rate
+
+  Example ADS1015 channel node:
+
+    channel@4 {
+	    reg = <4>;
+	    ti,gain = <3>;
+	    ti,datarate = <5>;
+    };
diff --git a/Documentation/hwmon/ads1015 b/Documentation/hwmon/ads1015
new file mode 100644
index 0000000..f6fe9c2
--- /dev/null
+++ b/Documentation/hwmon/ads1015
@@ -0,0 +1,72 @@
+Kernel driver ads1015
+=====================
+
+Supported chips:
+  * Texas Instruments ADS1015
+    Prefix: 'ads1015'
+    Datasheet: Publicly available at the Texas Instruments website :
+               http://focus.ti.com/lit/ds/symlink/ads1015.pdf
+
+Authors:
+        Dirk Eibach, Guntermann & Drunck GmbH <eibach@gdsys.de>
+
+Description
+-----------
+
+This driver implements support for the Texas Instruments ADS1015.
+
+This device is a 12-bit A-D converter with 4 inputs.
+
+The inputs can be used single ended or in certain differential combinations.
+
+The inputs can be made available by 8 sysfs input files in0_input - in7_input:
+in0: Voltage over AIN0 and AIN1.
+in1: Voltage over AIN0 and AIN3.
+in2: Voltage over AIN1 and AIN3.
+in3: Voltage over AIN2 and AIN3.
+in4: Voltage over AIN0 and GND.
+in5: Voltage over AIN1 and GND.
+in6: Voltage over AIN2 and GND.
+in7: Voltage over AIN3 and GND.
+
+Which inputs are available can be configured using platform data or devicetree.
+
+By default all inputs are exported.
+
+Platform Data
+-------------
+
+In linux/i2c/ads1015.h platform data is defined, channel_data contains
+configuration data for the used input combinations:
+- pga is the programmable gain amplifier (values are full scale)
+  0: +/- 6.144 V
+  1: +/- 4.096 V
+  2: +/- 2.048 V
+  3: +/- 1.024 V
+  4: +/- 0.512 V
+  5: +/- 0.256 V
+- data_rate in samples per second
+  0: 128
+  1: 250
+  2: 490
+  3: 920
+  4: 1600
+  5: 2400
+  6: 3300
+
+Example:
+struct ads1015_platform_data data = {
+	.channel_data = {
+		[2] = { .enabled = true, .pga = 1, .data_rate = 0 },
+		[4] = { .enabled = true, .pga = 4, .data_rate = 5 },
+	}
+};
+
+In this case only in2_input (FS +/- 4.096 V, 128 SPS) and in4_input
+(FS +/- 0.512 V, 2400 SPS) would be created.
+
+Devicetree
+----------
+
+Configuration is also possible via devicetree:
+Documentation/devicetree/bindings/hwmon/ads1015.txt
diff --git a/Documentation/hwmon/lm75 b/Documentation/hwmon/lm75
index 8e6356f..a179040 100644
--- a/Documentation/hwmon/lm75
+++ b/Documentation/hwmon/lm75
@@ -7,6 +7,11 @@
     Addresses scanned: I2C 0x48 - 0x4f
     Datasheet: Publicly available at the National Semiconductor website
                http://www.national.com/
+  * National Semiconductor LM75A
+    Prefix: 'lm75a'
+    Addresses scanned: I2C 0x48 - 0x4f
+    Datasheet: Publicly available at the National Semiconductor website
+               http://www.national.com/
   * Dallas Semiconductor DS75
     Prefix: 'lm75'
     Addresses scanned: I2C 0x48 - 0x4f
diff --git a/Documentation/hwmon/sch5627 b/Documentation/hwmon/sch5627
new file mode 100644
index 0000000..446a054
--- /dev/null
+++ b/Documentation/hwmon/sch5627
@@ -0,0 +1,22 @@
+Kernel driver sch5627
+=====================
+
+Supported chips:
+  * SMSC SCH5627
+    Prefix: 'sch5627'
+    Addresses scanned: none, address read from Super I/O config space
+    Datasheet: Application Note available upon request
+
+Author: Hans de Goede <hdegoede@redhat.com>
+
+
+Description
+-----------
+
+SMSC SCH5627 Super I/O chips include complete hardware monitoring
+capabilities. They can monitor up to 5 voltages, 4 fans and 8 temperatures.
+
+The hardware monitoring part of the SMSC SCH5627 is accessed by talking
+through an embedded microcontroller. An application note describing the
+protocol for communicating with the microcontroller is available upon
+request. Please mail me if you want a copy.
diff --git a/Documentation/hwmon/w83795 b/Documentation/hwmon/w83795
new file mode 100644
index 0000000..9f16037
--- /dev/null
+++ b/Documentation/hwmon/w83795
@@ -0,0 +1,127 @@
+Kernel driver w83795
+====================
+
+Supported chips:
+  * Winbond/Nuvoton W83795G
+    Prefix: 'w83795g'
+    Addresses scanned: I2C 0x2c - 0x2f
+    Datasheet: Available for download on nuvoton.com
+  * Winbond/Nuvoton W83795ADG
+    Prefix: 'w83795adg'
+    Addresses scanned: I2C 0x2c - 0x2f
+    Datasheet: Available for download on nuvoton.com
+
+Authors:
+    Wei Song (Nuvoton)
+    Jean Delvare <khali@linux-fr.org>
+
+
+Pin mapping
+-----------
+
+Here is a summary of the pin mapping for the W83795G and W83795ADG.
+This can be useful to convert data provided by board manufacturers
+into working libsensors configuration statements.
+
+    W83795G			|
+  Pin	| Name			| Register	| Sysfs attribute
+------------------------------------------------------------------
+   13	| VSEN1 (VCORE1)	| 10h		| in0
+   14	| VSEN2 (VCORE2)	| 11h		| in1
+   15	| VSEN3 (VCORE3)	| 12h		| in2
+   16	| VSEN4			| 13h		| in3
+   17	| VSEN5			| 14h		| in4
+   18	| VSEN6			| 15h		| in5
+   19	| VSEN7			| 16h		| in6
+   20	| VSEN8			| 17h		| in7
+   21	| VSEN9			| 18h		| in8
+   22	| VSEN10		| 19h		| in9
+   23	| VSEN11		| 1Ah		| in10
+   28	| VTT			| 1Bh		| in11
+   24	| 3VDD			| 1Ch		| in12
+   25	| 3VSB			| 1Dh		| in13
+   26	| VBAT			| 1Eh		| in14
+    3	| VSEN12/TR5		| 1Fh		| in15/temp5
+    4	| VSEN13/TR5		| 20h		| in16/temp6
+  5/  6	| VDSEN14/TR1/TD1	| 21h		| in17/temp1
+  7/  8	| VDSEN15/TR2/TD2	| 22h		| in18/temp2
+  9/ 10	| VDSEN16/TR3/TD3	| 23h		| in19/temp3
+ 11/ 12	| VDSEN17/TR4/TD4	| 24h		| in20/temp4
+   40	| FANIN1		| 2Eh		| fan1
+   42	| FANIN2		| 2Fh		| fan2
+   44	| FANIN3		| 30h		| fan3
+   46	| FANIN4		| 31h		| fan4
+   48	| FANIN5		| 32h		| fan5
+   50	| FANIN6		| 33h		| fan6
+   52	| FANIN7		| 34h		| fan7
+   54	| FANIN8		| 35h		| fan8
+   57	| FANIN9		| 36h		| fan9
+   58	| FANIN10		| 37h		| fan10
+   59	| FANIN11		| 38h		| fan11
+   60	| FANIN12		| 39h		| fan12
+   31	| FANIN13		| 3Ah		| fan13
+   35	| FANIN14		| 3Bh		| fan14
+   41	| FANCTL1		| 10h (bank 2)	| pwm1
+   43	| FANCTL2		| 11h (bank 2)	| pwm2
+   45	| FANCTL3		| 12h (bank 2)	| pwm3
+   47	| FANCTL4		| 13h (bank 2)	| pwm4
+   49	| FANCTL5		| 14h (bank 2)	| pwm5
+   51	| FANCTL6		| 15h (bank 2)	| pwm6
+   53	| FANCTL7		| 16h (bank 2)	| pwm7
+   55	| FANCTL8		| 17h (bank 2)	| pwm8
+ 29/ 30	| PECI/TSI (DTS1)	| 26h		| temp7
+ 29/ 30	| PECI/TSI (DTS2)	| 27h		| temp8
+ 29/ 30	| PECI/TSI (DTS3)	| 28h		| temp9
+ 29/ 30	| PECI/TSI (DTS4)	| 29h		| temp10
+ 29/ 30	| PECI/TSI (DTS5)	| 2Ah		| temp11
+ 29/ 30	| PECI/TSI (DTS6)	| 2Bh		| temp12
+ 29/ 30	| PECI/TSI (DTS7)	| 2Ch		| temp13
+ 29/ 30	| PECI/TSI (DTS8)	| 2Dh		| temp14
+   27	| CASEOPEN#		| 46h		| intrusion0
+
+    W83795ADG			|
+  Pin	| Name			| Register	| Sysfs attribute
+------------------------------------------------------------------
+   10	| VSEN1 (VCORE1)	| 10h		| in0
+   11	| VSEN2 (VCORE2)	| 11h		| in1
+   12	| VSEN3 (VCORE3)	| 12h		| in2
+   13	| VSEN4			| 13h		| in3
+   14	| VSEN5			| 14h		| in4
+   15	| VSEN6			| 15h		| in5
+   16	| VSEN7			| 16h		| in6
+   17	| VSEN8			| 17h		| in7
+   22	| VTT			| 1Bh		| in11
+   18	| 3VDD			| 1Ch		| in12
+   19	| 3VSB			| 1Dh		| in13
+   20	| VBAT			| 1Eh		| in14
+   48	| VSEN12/TR5		| 1Fh		| in15/temp5
+    1	| VSEN13/TR5		| 20h		| in16/temp6
+  2/  3	| VDSEN14/TR1/TD1	| 21h		| in17/temp1
+  4/  5	| VDSEN15/TR2/TD2	| 22h		| in18/temp2
+  6/  7	| VDSEN16/TR3/TD3	| 23h		| in19/temp3
+  8/  9	| VDSEN17/TR4/TD4	| 24h		| in20/temp4
+   32	| FANIN1		| 2Eh		| fan1
+   34	| FANIN2		| 2Fh		| fan2
+   36	| FANIN3		| 30h		| fan3
+   37	| FANIN4		| 31h		| fan4
+   38	| FANIN5		| 32h		| fan5
+   39	| FANIN6		| 33h		| fan6
+   40	| FANIN7		| 34h		| fan7
+   41	| FANIN8		| 35h		| fan8
+   43	| FANIN9		| 36h		| fan9
+   44	| FANIN10		| 37h		| fan10
+   45	| FANIN11		| 38h		| fan11
+   46	| FANIN12		| 39h		| fan12
+   24	| FANIN13		| 3Ah		| fan13
+   28	| FANIN14		| 3Bh		| fan14
+   33	| FANCTL1		| 10h (bank 2)	| pwm1
+   35	| FANCTL2		| 11h (bank 2)	| pwm2
+   23	| PECI (DTS1)		| 26h		| temp7
+   23	| PECI (DTS2)		| 27h		| temp8
+   23	| PECI (DTS3)		| 28h		| temp9
+   23	| PECI (DTS4)		| 29h		| temp10
+   23	| PECI (DTS5)		| 2Ah		| temp11
+   23	| PECI (DTS6)		| 2Bh		| temp12
+   23	| PECI (DTS7)		| 2Ch		| temp13
+   23	| PECI (DTS8)		| 2Dh		| temp14
+   21	| CASEOPEN#		| 46h		| intrusion0
diff --git a/Documentation/hwmon/hpfall.c b/Documentation/laptops/hpfall.c
similarity index 100%
rename from Documentation/hwmon/hpfall.c
rename to Documentation/laptops/hpfall.c
diff --git a/Documentation/hwmon/lis3lv02d b/Documentation/misc-devices/lis3lv02d
similarity index 96%
rename from Documentation/hwmon/lis3lv02d
rename to Documentation/misc-devices/lis3lv02d
index 06534f2..f1a4ec8 100644
--- a/Documentation/hwmon/lis3lv02d
+++ b/Documentation/misc-devices/lis3lv02d
@@ -17,8 +17,8 @@
 This driver provides support for the accelerometer found in various HP laptops
 sporting the feature officially called "HP Mobile Data Protection System 3D" or
 "HP 3D DriveGuard". It detects automatically laptops with this sensor. Known
-models (full list can be found in drivers/hwmon/hp_accel.c) will have their
-axis automatically oriented on standard way (eg: you can directly play
+models (full list can be found in drivers/platform/x86/hp_accel.c) will have
+their axis automatically oriented on standard way (eg: you can directly play
 neverball). The accelerometer data is readable via
 /sys/devices/platform/lis3lv02d. Reported values are scaled
 to mg values (1/1000th of earth gravity).
diff --git a/MAINTAINERS b/MAINTAINERS
index c7a41b1..38077a6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -198,7 +198,7 @@
 F:	drivers/scsi/aacraid/
 
 ABIT UGURU 1,2 HARDWARE MONITOR DRIVER
-M:	Hans de Goede <j.w.r.degoede@hhs.nl>
+M:	Hans de Goede <hdegoede@redhat.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	drivers/hwmon/abituguru.c
@@ -365,6 +365,14 @@
 S:	Supported
 F:	drivers/video/backlight/adp8860_bl.c
 
+ADS1015 HARDWARE MONITOR DRIVER
+M:	Dirk Eibach <eibach@gdsys.de>
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+F:	Documentation/hwmon/ads1015
+F:	drivers/hwmon/ads1015.c
+F:	include/linux/i2c/ads1015.h
+
 ADT746X FAN DRIVER
 M:	Colin Leroy <colin@colino.net>
 S:	Maintained
@@ -3913,8 +3921,8 @@
 LIS3LV02D ACCELEROMETER DRIVER
 M:	Eric Piel <eric.piel@tremplin-utc.net>
 S:	Maintained
-F:	Documentation/hwmon/lis3lv02d
-F:	drivers/hwmon/lis3lv02d.*
+F:	Documentation/misc-devices/lis3lv02d
+F:	drivers/misc/lis3lv02d/
 
 LLC (802.2)
 M:	Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
@@ -5769,6 +5777,13 @@
 F:	Documentation/hwmon/emc2103
 F:	drivers/hwmon/emc2103.c
 
+SMSC SCH5627 HARDWARE MONITOR DRIVER
+M:	Hans de Goede <hdegoede@redhat.com>
+L:	lm-sensors@lm-sensors.org
+S:	Supported
+F:	Documentation/hwmon/sch5627
+F:	drivers/hwmon/sch5627.c
+
 SMSC47B397 HARDWARE MONITOR DRIVER
 M:	"Mark M. Hoffman" <mhoffman@lightlink.com>
 L:	lm-sensors@lm-sensors.org
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 1bfb443..e4bd13b 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -521,7 +521,7 @@
 		- Dallas Semiconductor DS75 and DS1775
 		- Maxim MAX6625 and MAX6626
 		- Microchip MCP980x
-		- National Semiconductor LM75
+		- National Semiconductor LM75, LM75A
 		- NXP's LM75A
 		- ST Microelectronics STDS75
 		- TelCom (now Microchip) TCN75
@@ -959,6 +959,25 @@
 	  This driver can also be built as a module.  If so, the module
 	  will be called smsc47b397.
 
+config SENSORS_SCH5627
+	tristate "SMSC SCH5627"
+	help
+	  If you say yes here you get support for the hardware monitoring
+	  features of the SMSC SCH5627 Super-I/O chip.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called sch5627.
+
+config SENSORS_ADS1015
+	tristate "Texas Instruments ADS1015"
+	depends on I2C
+	help
+	  If you say yes here you get support for Texas Instruments ADS1015
+	  12-bit 4-input ADC device.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called ads1015.
+
 config SENSORS_ADS7828
 	tristate "Texas Instruments ADS7828"
 	depends on I2C
@@ -1215,40 +1234,6 @@
 	  This driver provides support for the Ultra45 workstation environmental
 	  sensors.
 
-config SENSORS_LIS3_SPI
-	tristate "STMicroeletronics LIS3LV02Dx three-axis digital accelerometer (SPI)"
-	depends on !ACPI && SPI_MASTER && INPUT
-	select INPUT_POLLDEV
-	default n
-	help
-	  This driver provides support for the LIS3LV02Dx accelerometer connected
-	  via SPI. The accelerometer data is readable via
-	  /sys/devices/platform/lis3lv02d.
-
-	  This driver also provides an absolute input class device, allowing
-	  the laptop to act as a pinball machine-esque joystick.
-
-	  This driver can also be built as modules.  If so, the core module
-	  will be called lis3lv02d and a specific module for the SPI transport
-	  is called lis3lv02d_spi.
-
-config SENSORS_LIS3_I2C
-	tristate "STMicroeletronics LIS3LV02Dx three-axis digital accelerometer (I2C)"
-	depends on I2C && INPUT
-	select INPUT_POLLDEV
-	default n
-	help
-	  This driver provides support for the LIS3LV02Dx accelerometer connected
-	  via I2C. The accelerometer data is readable via
-	  /sys/devices/platform/lis3lv02d.
-
-	  This driver also provides an absolute input class device, allowing
-	  the device to act as a pinball machine-esque joystick.
-
-	  This driver can also be built as modules.  If so, the core module
-	  will be called lis3lv02d and a specific module for the I2C transport
-	  is called lis3lv02d_i2c.
-
 config SENSORS_APPLESMC
 	tristate "Apple SMC (Motion sensor, light sensor, keyboard backlight)"
 	depends on INPUT && X86
@@ -1296,36 +1281,6 @@
 	  This driver can also be built as a module. If so, the module
 	  will be called asus_atk0110.
 
-config SENSORS_LIS3LV02D
-	tristate "STMicroeletronics LIS3* three-axis digital accelerometer"
-	depends on INPUT
-	select INPUT_POLLDEV
-	select NEW_LEDS
-	select LEDS_CLASS
-	default n
-	help
-	  This driver provides support for the LIS3* accelerometers, such as the
-	  LIS3LV02DL or the LIS331DL. In particular, it can be found in a number
-	  of HP laptops, which have the "Mobile Data Protection System 3D" or
-	  "3D DriveGuard" feature. On such systems the driver should load
-	  automatically (via ACPI alias). The accelerometer might also be found
-	  in other systems, connected via SPI or I2C. The accelerometer data is
-	  readable via /sys/devices/platform/lis3lv02d.
-
-	  This driver also provides an absolute input class device, allowing
-	  a laptop to act as a pinball machine-esque joystick. It provides also
-	  a misc device which can be used to detect free-fall. On HP laptops,
-	  if the led infrastructure is activated, support for a led indicating
-	  disk protection will be provided as hp::hddprotect. For more
-	  information on the feature, refer to Documentation/hwmon/lis3lv02d.
-
-	  This driver can also be built as modules.  If so, the core module
-	  will be called lis3lv02d and a specific module for HP laptops will be
-	  called hp_accel.
-
-	  Say Y here if you have an applicable laptop and want to experience
-	  the awesome power of lis3lv02d.
-
 endif # ACPI
 
 endif # HWMON
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 8a238de..54ca593 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -29,6 +29,7 @@
 obj-$(CONFIG_SENSORS_ADM1029)	+= adm1029.o
 obj-$(CONFIG_SENSORS_ADM1031)	+= adm1031.o
 obj-$(CONFIG_SENSORS_ADM9240)	+= adm9240.o
+obj-$(CONFIG_SENSORS_ADS1015)	+= ads1015.o
 obj-$(CONFIG_SENSORS_ADS7828)	+= ads7828.o
 obj-$(CONFIG_SENSORS_ADS7871)	+= ads7871.o
 obj-$(CONFIG_SENSORS_ADT7411)	+= adt7411.o
@@ -63,9 +64,6 @@
 obj-$(CONFIG_SENSORS_K8TEMP)	+= k8temp.o
 obj-$(CONFIG_SENSORS_K10TEMP)	+= k10temp.o
 obj-$(CONFIG_SENSORS_LINEAGE)	+= lineage-pem.o
-obj-$(CONFIG_SENSORS_LIS3LV02D) += lis3lv02d.o hp_accel.o
-obj-$(CONFIG_SENSORS_LIS3_SPI)	+= lis3lv02d.o lis3lv02d_spi.o
-obj-$(CONFIG_SENSORS_LIS3_I2C)	+= lis3lv02d.o lis3lv02d_i2c.o
 obj-$(CONFIG_SENSORS_LM63)	+= lm63.o
 obj-$(CONFIG_SENSORS_LM70)	+= lm70.o
 obj-$(CONFIG_SENSORS_LM73)	+= lm73.o
@@ -93,6 +91,7 @@
 obj-$(CONFIG_SENSORS_PC87427)	+= pc87427.o
 obj-$(CONFIG_SENSORS_PCF8591)	+= pcf8591.o
 obj-$(CONFIG_SENSORS_S3C)	+= s3c-hwmon.o
+obj-$(CONFIG_SENSORS_SCH5627)	+= sch5627.o
 obj-$(CONFIG_SENSORS_SHT15)	+= sht15.o
 obj-$(CONFIG_SENSORS_SHT21)	+= sht21.o
 obj-$(CONFIG_SENSORS_SIS5595)	+= sis5595.o
diff --git a/drivers/hwmon/abituguru.c b/drivers/hwmon/abituguru.c
index 8f07a9d..0e05aa1 100644
--- a/drivers/hwmon/abituguru.c
+++ b/drivers/hwmon/abituguru.c
@@ -1,5 +1,5 @@
 /*
-    abituguru.c Copyright (c) 2005-2006 Hans de Goede <j.w.r.degoede@hhs.nl>
+    abituguru.c Copyright (c) 2005-2006 Hans de Goede <hdegoede@redhat.com>
 
     This program is free software; you can redistribute it and/or modify
     it under the terms of the GNU General Public License as published by
@@ -1505,7 +1505,7 @@
 	platform_driver_unregister(&abituguru_driver);
 }
 
-MODULE_AUTHOR("Hans de Goede <j.w.r.degoede@hhs.nl>");
+MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
 MODULE_DESCRIPTION("Abit uGuru Sensor device");
 MODULE_LICENSE("GPL");
 
diff --git a/drivers/hwmon/abituguru3.c b/drivers/hwmon/abituguru3.c
index 48d21e2..034cebf 100644
--- a/drivers/hwmon/abituguru3.c
+++ b/drivers/hwmon/abituguru3.c
@@ -1,7 +1,7 @@
 /*
     abituguru3.c
 
-    Copyright (c) 2006-2008 Hans de Goede <j.w.r.degoede@hhs.nl>
+    Copyright (c) 2006-2008 Hans de Goede <hdegoede@redhat.com>
     Copyright (c) 2008 Alistair John Strachan <alistair@devzero.co.uk>
 
     This program is free software; you can redistribute it and/or modify
@@ -1266,7 +1266,7 @@
 	platform_driver_unregister(&abituguru3_driver);
 }
 
-MODULE_AUTHOR("Hans de Goede <j.w.r.degoede@hhs.nl>");
+MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
 MODULE_DESCRIPTION("Abit uGuru3 Sensor device");
 MODULE_LICENSE("GPL");
 
diff --git a/drivers/hwmon/ads1015.c b/drivers/hwmon/ads1015.c
new file mode 100644
index 0000000..e9beeda
--- /dev/null
+++ b/drivers/hwmon/ads1015.c
@@ -0,0 +1,337 @@
+/*
+ * ads1015.c - lm_sensors driver for ads1015 12-bit 4-input ADC
+ * (C) Copyright 2010
+ * Dirk Eibach, Guntermann & Drunck GmbH <eibach@gdsys.de>
+ *
+ * Based on the ads7828 driver by Steve Hardy.
+ *
+ * Datasheet available at: http://focus.ti.com/lit/ds/symlink/ads1015.pdf
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+
+#include <linux/i2c/ads1015.h>
+
+/* ADS1015 registers */
+enum {
+	ADS1015_CONVERSION = 0,
+	ADS1015_CONFIG = 1,
+};
+
+/* PGA fullscale voltages in mV */
+static const unsigned int fullscale_table[8] = {
+	6144, 4096, 2048, 1024, 512, 256, 256, 256 };
+
+/* Data rates in samples per second */
+static const unsigned int data_rate_table[8] = {
+	128, 250, 490, 920, 1600, 2400, 3300, 3300 };
+
+#define ADS1015_DEFAULT_CHANNELS 0xff
+#define ADS1015_DEFAULT_PGA 2
+#define ADS1015_DEFAULT_DATA_RATE 4
+
+struct ads1015_data {
+	struct device *hwmon_dev;
+	struct mutex update_lock; /* mutex protect updates */
+	struct ads1015_channel_data channel_data[ADS1015_CHANNELS];
+};
+
+static s32 ads1015_read_reg(struct i2c_client *client, unsigned int reg)
+{
+	s32 data = i2c_smbus_read_word_data(client, reg);
+
+	return (data < 0) ? data : swab16(data);
+}
+
+static s32 ads1015_write_reg(struct i2c_client *client, unsigned int reg,
+			     u16 val)
+{
+	return i2c_smbus_write_word_data(client, reg, swab16(val));
+}
+
+static int ads1015_read_value(struct i2c_client *client, unsigned int channel,
+			      int *value)
+{
+	u16 config;
+	s16 conversion;
+	struct ads1015_data *data = i2c_get_clientdata(client);
+	unsigned int pga = data->channel_data[channel].pga;
+	int fullscale;
+	unsigned int data_rate = data->channel_data[channel].data_rate;
+	unsigned int conversion_time_ms;
+	int res;
+
+	mutex_lock(&data->update_lock);
+
+	/* get channel parameters */
+	res = ads1015_read_reg(client, ADS1015_CONFIG);
+	if (res < 0)
+		goto err_unlock;
+	config = res;
+	fullscale = fullscale_table[pga];
+	conversion_time_ms = DIV_ROUND_UP(1000, data_rate_table[data_rate]);
+
+	/* setup and start single conversion */
+	config &= 0x001f;
+	config |= (1 << 15) | (1 << 8);
+	config |= (channel & 0x0007) << 12;
+	config |= (pga & 0x0007) << 9;
+	config |= (data_rate & 0x0007) << 5;
+
+	res = ads1015_write_reg(client, ADS1015_CONFIG, config);
+	if (res < 0)
+		goto err_unlock;
+
+	/* wait until conversion finished */
+	msleep(conversion_time_ms);
+	res = ads1015_read_reg(client, ADS1015_CONFIG);
+	if (res < 0)
+		goto err_unlock;
+	config = res;
+	if (!(config & (1 << 15))) {
+		/* conversion not finished in time */
+		res = -EIO;
+		goto err_unlock;
+	}
+
+	res = ads1015_read_reg(client, ADS1015_CONVERSION);
+	if (res < 0)
+		goto err_unlock;
+	conversion = res;
+
+	mutex_unlock(&data->update_lock);
+
+	*value = DIV_ROUND_CLOSEST(conversion * fullscale, 0x7ff0);
+
+	return 0;
+
+err_unlock:
+	mutex_unlock(&data->update_lock);
+	return res;
+}
+
+/* sysfs callback function */
+static ssize_t show_in(struct device *dev, struct device_attribute *da,
+	char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	struct i2c_client *client = to_i2c_client(dev);
+	int in;
+	int res;
+
+	res = ads1015_read_value(client, attr->index, &in);
+
+	return (res < 0) ? res : sprintf(buf, "%d\n", in);
+}
+
+static const struct sensor_device_attribute ads1015_in[] = {
+	SENSOR_ATTR(in0_input, S_IRUGO, show_in, NULL, 0),
+	SENSOR_ATTR(in1_input, S_IRUGO, show_in, NULL, 1),
+	SENSOR_ATTR(in2_input, S_IRUGO, show_in, NULL, 2),
+	SENSOR_ATTR(in3_input, S_IRUGO, show_in, NULL, 3),
+	SENSOR_ATTR(in4_input, S_IRUGO, show_in, NULL, 4),
+	SENSOR_ATTR(in5_input, S_IRUGO, show_in, NULL, 5),
+	SENSOR_ATTR(in6_input, S_IRUGO, show_in, NULL, 6),
+	SENSOR_ATTR(in7_input, S_IRUGO, show_in, NULL, 7),
+};
+
+/*
+ * Driver interface
+ */
+
+static int ads1015_remove(struct i2c_client *client)
+{
+	struct ads1015_data *data = i2c_get_clientdata(client);
+	int k;
+
+	hwmon_device_unregister(data->hwmon_dev);
+	for (k = 0; k < ADS1015_CHANNELS; ++k)
+		device_remove_file(&client->dev, &ads1015_in[k].dev_attr);
+	kfree(data);
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static int ads1015_get_channels_config_of(struct i2c_client *client)
+{
+	struct ads1015_data *data = i2c_get_clientdata(client);
+	struct device_node *node;
+
+	if (!client->dev.of_node
+	    || !of_get_next_child(client->dev.of_node, NULL))
+		return -EINVAL;
+
+	for_each_child_of_node(client->dev.of_node, node) {
+		const __be32 *property;
+		int len;
+		unsigned int channel;
+		unsigned int pga = ADS1015_DEFAULT_PGA;
+		unsigned int data_rate = ADS1015_DEFAULT_DATA_RATE;
+
+		property = of_get_property(node, "reg", &len);
+		if (!property || len != sizeof(int)) {
+			dev_err(&client->dev, "invalid reg on %s\n",
+				node->full_name);
+			continue;
+		}
+
+		channel = be32_to_cpup(property);
+		if (channel > ADS1015_CHANNELS) {
+			dev_err(&client->dev,
+				"invalid channel index %d on %s\n",
+				channel, node->full_name);
+			continue;
+		}
+
+		property = of_get_property(node, "ti,gain", &len);
+		if (property && len == sizeof(int)) {
+			pga = be32_to_cpup(property);
+			if (pga > 6) {
+				dev_err(&client->dev,
+					"invalid gain on %s\n",
+					node->full_name);
+			}
+		}
+
+		property = of_get_property(node, "ti,datarate", &len);
+		if (property && len == sizeof(int)) {
+			data_rate = be32_to_cpup(property);
+			if (data_rate > 7) {
+				dev_err(&client->dev,
+					"invalid data_rate on %s\n",
+					node->full_name);
+			}
+		}
+
+		data->channel_data[channel].enabled = true;
+		data->channel_data[channel].pga = pga;
+		data->channel_data[channel].data_rate = data_rate;
+	}
+
+	return 0;
+}
+#endif
+
+static void ads1015_get_channels_config(struct i2c_client *client)
+{
+	unsigned int k;
+	struct ads1015_data *data = i2c_get_clientdata(client);
+	struct ads1015_platform_data *pdata = dev_get_platdata(&client->dev);
+
+	/* prefer platform data */
+	if (pdata) {
+		memcpy(data->channel_data, pdata->channel_data,
+		       sizeof(data->channel_data));
+		return;
+	}
+
+#ifdef CONFIG_OF
+	if (!ads1015_get_channels_config_of(client))
+		return;
+#endif
+
+	/* fallback on default configuration */
+	for (k = 0; k < ADS1015_CHANNELS; ++k) {
+		data->channel_data[k].enabled = true;
+		data->channel_data[k].pga = ADS1015_DEFAULT_PGA;
+		data->channel_data[k].data_rate = ADS1015_DEFAULT_DATA_RATE;
+	}
+}
+
+static int ads1015_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct ads1015_data *data;
+	int err;
+	unsigned int k;
+
+	data = kzalloc(sizeof(struct ads1015_data), GFP_KERNEL);
+	if (!data) {
+		err = -ENOMEM;
+		goto exit;
+	}
+
+	i2c_set_clientdata(client, data);
+	mutex_init(&data->update_lock);
+
+	/* build sysfs attribute group */
+	ads1015_get_channels_config(client);
+	for (k = 0; k < ADS1015_CHANNELS; ++k) {
+		if (!data->channel_data[k].enabled)
+			continue;
+		err = device_create_file(&client->dev, &ads1015_in[k].dev_attr);
+		if (err)
+			goto exit_free;
+	}
+
+	data->hwmon_dev = hwmon_device_register(&client->dev);
+	if (IS_ERR(data->hwmon_dev)) {
+		err = PTR_ERR(data->hwmon_dev);
+		goto exit_remove;
+	}
+
+	return 0;
+
+exit_remove:
+	for (k = 0; k < ADS1015_CHANNELS; ++k)
+		device_remove_file(&client->dev, &ads1015_in[k].dev_attr);
+exit_free:
+	kfree(data);
+exit:
+	return err;
+}
+
+static const struct i2c_device_id ads1015_id[] = {
+	{ "ads1015", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, ads1015_id);
+
+static struct i2c_driver ads1015_driver = {
+	.driver = {
+		.name = "ads1015",
+	},
+	.probe = ads1015_probe,
+	.remove = ads1015_remove,
+	.id_table = ads1015_id,
+};
+
+static int __init sensors_ads1015_init(void)
+{
+	return i2c_add_driver(&ads1015_driver);
+}
+
+static void __exit sensors_ads1015_exit(void)
+{
+	i2c_del_driver(&ads1015_driver);
+}
+
+MODULE_AUTHOR("Dirk Eibach <eibach@gdsys.de>");
+MODULE_DESCRIPTION("ADS1015 driver");
+MODULE_LICENSE("GPL");
+
+module_init(sensors_ads1015_init);
+module_exit(sensors_ads1015_exit);
diff --git a/drivers/hwmon/lm75.c b/drivers/hwmon/lm75.c
index f36eb80..ef902d5 100644
--- a/drivers/hwmon/lm75.c
+++ b/drivers/hwmon/lm75.c
@@ -232,13 +232,16 @@
 };
 MODULE_DEVICE_TABLE(i2c, lm75_ids);
 
+#define LM75A_ID 0xA1
+
 /* Return 0 if detection is successful, -ENODEV otherwise */
 static int lm75_detect(struct i2c_client *new_client,
 		       struct i2c_board_info *info)
 {
 	struct i2c_adapter *adapter = new_client->adapter;
 	int i;
-	int cur, conf, hyst, os;
+	int conf, hyst, os;
+	bool is_lm75a = 0;
 
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA |
 				     I2C_FUNC_SMBUS_WORD_DATA))
@@ -250,37 +253,58 @@
 	   addresses 0x04-0x07 returning the last read value.
 	   The cycling+unused addresses combination is not tested,
 	   since it would significantly slow the detection down and would
-	   hardly add any value. */
+	   hardly add any value.
 
-	/* Unused addresses */
-	cur = i2c_smbus_read_word_data(new_client, 0);
-	conf = i2c_smbus_read_byte_data(new_client, 1);
-	hyst = i2c_smbus_read_word_data(new_client, 2);
-	if (i2c_smbus_read_word_data(new_client, 4) != hyst
-	 || i2c_smbus_read_word_data(new_client, 5) != hyst
-	 || i2c_smbus_read_word_data(new_client, 6) != hyst
-	 || i2c_smbus_read_word_data(new_client, 7) != hyst)
-		return -ENODEV;
-	os = i2c_smbus_read_word_data(new_client, 3);
-	if (i2c_smbus_read_word_data(new_client, 4) != os
-	 || i2c_smbus_read_word_data(new_client, 5) != os
-	 || i2c_smbus_read_word_data(new_client, 6) != os
-	 || i2c_smbus_read_word_data(new_client, 7) != os)
-		return -ENODEV;
+	   The National Semiconductor LM75A is different than earlier
+	   LM75s.  It has an ID byte of 0xaX (where X is the chip
+	   revision, with 1 being the only revision in existence) in
+	   register 7, and unused registers return 0xff rather than the
+	   last read value. */
 
 	/* Unused bits */
+	conf = i2c_smbus_read_byte_data(new_client, 1);
 	if (conf & 0xe0)
 		return -ENODEV;
 
-	/* Addresses cycling */
-	for (i = 8; i < 0xff; i += 8) {
-		if (i2c_smbus_read_byte_data(new_client, i + 1) != conf
-		 || i2c_smbus_read_word_data(new_client, i + 2) != hyst
-		 || i2c_smbus_read_word_data(new_client, i + 3) != os)
+	/* First check for LM75A */
+	if (i2c_smbus_read_byte_data(new_client, 7) == LM75A_ID) {
+		/* LM75A returns 0xff on unused registers so
+		   just to be sure we check for that too. */
+		if (i2c_smbus_read_byte_data(new_client, 4) != 0xff
+		 || i2c_smbus_read_byte_data(new_client, 5) != 0xff
+		 || i2c_smbus_read_byte_data(new_client, 6) != 0xff)
+			return -ENODEV;
+		is_lm75a = 1;
+		hyst = i2c_smbus_read_byte_data(new_client, 2);
+		os = i2c_smbus_read_byte_data(new_client, 3);
+	} else { /* Traditional style LM75 detection */
+		/* Unused addresses */
+		hyst = i2c_smbus_read_byte_data(new_client, 2);
+		if (i2c_smbus_read_byte_data(new_client, 4) != hyst
+		 || i2c_smbus_read_byte_data(new_client, 5) != hyst
+		 || i2c_smbus_read_byte_data(new_client, 6) != hyst
+		 || i2c_smbus_read_byte_data(new_client, 7) != hyst)
+			return -ENODEV;
+		os = i2c_smbus_read_byte_data(new_client, 3);
+		if (i2c_smbus_read_byte_data(new_client, 4) != os
+		 || i2c_smbus_read_byte_data(new_client, 5) != os
+		 || i2c_smbus_read_byte_data(new_client, 6) != os
+		 || i2c_smbus_read_byte_data(new_client, 7) != os)
 			return -ENODEV;
 	}
 
-	strlcpy(info->type, "lm75", I2C_NAME_SIZE);
+	/* Addresses cycling */
+	for (i = 8; i <= 248; i += 40) {
+		if (i2c_smbus_read_byte_data(new_client, i + 1) != conf
+		 || i2c_smbus_read_byte_data(new_client, i + 2) != hyst
+		 || i2c_smbus_read_byte_data(new_client, i + 3) != os)
+			return -ENODEV;
+		if (is_lm75a && i2c_smbus_read_byte_data(new_client, i + 7)
+				!= LM75A_ID)
+			return -ENODEV;
+	}
+
+	strlcpy(info->type, is_lm75a ? "lm75a" : "lm75", I2C_NAME_SIZE);
 
 	return 0;
 }
diff --git a/drivers/hwmon/sch5627.c b/drivers/hwmon/sch5627.c
new file mode 100644
index 0000000..9a51dcc
--- /dev/null
+++ b/drivers/hwmon/sch5627.c
@@ -0,0 +1,858 @@
+/***************************************************************************
+ *   Copyright (C) 2010-2011 Hans de Goede <hdegoede@redhat.com>           *
+ *                                                                         *
+ *   This program is free software; you can redistribute it and/or modify  *
+ *   it under the terms of the GNU General Public License as published by  *
+ *   the Free Software Foundation; either version 2 of the License, or     *
+ *   (at your option) any later version.                                   *
+ *                                                                         *
+ *   This program is distributed in the hope that it will be useful,       *
+ *   but WITHOUT ANY WARRANTY; without even the implied warranty of        *
+ *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the         *
+ *   GNU General Public License for more details.                          *
+ *                                                                         *
+ *   You should have received a copy of the GNU General Public License     *
+ *   along with this program; if not, write to the                         *
+ *   Free Software Foundation, Inc.,                                       *
+ *   59 Temple Place - Suite 330, Boston, MA  02111-1307, USA.             *
+ ***************************************************************************/
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/platform_device.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/io.h>
+#include <linux/acpi.h>
+#include <linux/delay.h>
+
+#define DRVNAME "sch5627"
+#define DEVNAME DRVNAME /* We only support one model */
+
+#define SIO_SCH5627_EM_LD	0x0C	/* Embedded Microcontroller LD */
+#define SIO_UNLOCK_KEY		0x55	/* Key to enable Super-I/O */
+#define SIO_LOCK_KEY		0xAA	/* Key to disable Super-I/O */
+
+#define SIO_REG_LDSEL		0x07	/* Logical device select */
+#define SIO_REG_DEVID		0x20	/* Device ID */
+#define SIO_REG_ENABLE		0x30	/* Logical device enable */
+#define SIO_REG_ADDR		0x66	/* Logical device address (2 bytes) */
+
+#define SIO_SCH5627_ID		0xC6	/* Chipset ID */
+
+#define REGION_LENGTH		9
+
+#define SCH5627_HWMON_ID		0xa5
+#define SCH5627_COMPANY_ID		0x5c
+#define SCH5627_PRIMARY_ID		0xa0
+
+#define SCH5627_REG_BUILD_CODE		0x39
+#define SCH5627_REG_BUILD_ID		0x3a
+#define SCH5627_REG_HWMON_ID		0x3c
+#define SCH5627_REG_HWMON_REV		0x3d
+#define SCH5627_REG_COMPANY_ID		0x3e
+#define SCH5627_REG_PRIMARY_ID		0x3f
+#define SCH5627_REG_CTRL		0x40
+
+#define SCH5627_NO_TEMPS		8
+#define SCH5627_NO_FANS			4
+#define SCH5627_NO_IN			5
+
+static const u16 SCH5627_REG_TEMP_MSB[SCH5627_NO_TEMPS] = {
+	0x2B, 0x26, 0x27, 0x28, 0x29, 0x2A, 0x180, 0x181 };
+static const u16 SCH5627_REG_TEMP_LSN[SCH5627_NO_TEMPS] = {
+	0xE2, 0xE1, 0xE1, 0xE5, 0xE5, 0xE6, 0x182, 0x182 };
+static const u16 SCH5627_REG_TEMP_HIGH_NIBBLE[SCH5627_NO_TEMPS] = {
+	0, 0, 1, 1, 0, 0, 0, 1 };
+static const u16 SCH5627_REG_TEMP_HIGH[SCH5627_NO_TEMPS] = {
+	0x61, 0x57, 0x59, 0x5B, 0x5D, 0x5F, 0x184, 0x186 };
+static const u16 SCH5627_REG_TEMP_ABS[SCH5627_NO_TEMPS] = {
+	0x9B, 0x96, 0x97, 0x98, 0x99, 0x9A, 0x1A8, 0x1A9 };
+
+static const u16 SCH5627_REG_FAN[SCH5627_NO_FANS] = {
+	0x2C, 0x2E, 0x30, 0x32 };
+static const u16 SCH5627_REG_FAN_MIN[SCH5627_NO_FANS] = {
+	0x62, 0x64, 0x66, 0x68 };
+
+static const u16 SCH5627_REG_IN_MSB[SCH5627_NO_IN] = {
+	0x22, 0x23, 0x24, 0x25, 0x189 };
+static const u16 SCH5627_REG_IN_LSN[SCH5627_NO_IN] = {
+	0xE4, 0xE4, 0xE3, 0xE3, 0x18A };
+static const u16 SCH5627_REG_IN_HIGH_NIBBLE[SCH5627_NO_IN] = {
+	1, 0, 1, 0, 1 };
+static const u16 SCH5627_REG_IN_FACTOR[SCH5627_NO_IN] = {
+	10745, 3660, 9765, 10745, 3660 };
+static const char * const SCH5627_IN_LABELS[SCH5627_NO_IN] = {
+	"VCC", "VTT", "VBAT", "VTR", "V_IN" };
+
+struct sch5627_data {
+	unsigned short addr;
+	struct device *hwmon_dev;
+	u8 temp_max[SCH5627_NO_TEMPS];
+	u8 temp_crit[SCH5627_NO_TEMPS];
+	u16 fan_min[SCH5627_NO_FANS];
+
+	struct mutex update_lock;
+	char valid;			/* !=0 if following fields are valid */
+	unsigned long last_updated;	/* In jiffies */
+	u16 temp[SCH5627_NO_TEMPS];
+	u16 fan[SCH5627_NO_FANS];
+	u16 in[SCH5627_NO_IN];
+};
+
+static struct platform_device *sch5627_pdev;
+
+/* Super I/O functions */
+static inline int superio_inb(int base, int reg)
+{
+	outb(reg, base);
+	return inb(base + 1);
+}
+
+static inline int superio_enter(int base)
+{
+	/* Don't step on other drivers' I/O space by accident */
+	if (!request_muxed_region(base, 2, DRVNAME)) {
+		pr_err("I/O address 0x%04x already in use\n", base);
+		return -EBUSY;
+	}
+
+	outb(SIO_UNLOCK_KEY, base);
+
+	return 0;
+}
+
+static inline void superio_select(int base, int ld)
+{
+	outb(SIO_REG_LDSEL, base);
+	outb(ld, base + 1);
+}
+
+static inline void superio_exit(int base)
+{
+	outb(SIO_LOCK_KEY, base);
+	release_region(base, 2);
+}
+
+static int sch5627_read_virtual_reg(struct sch5627_data *data, u16 reg)
+{
+	u8 val;
+	int i;
+	/*
+	 * According to SMSC for the commands we use the maximum time for
+	 * the EM to respond is 15 ms, but testing shows in practice it
+	 * responds within 15-32 reads, so we first busy poll, and if
+	 * that fails sleep a bit and try again until we are way past
+	 * the 15 ms maximum response time.
+	 */
+	const int max_busy_polls = 64;
+	const int max_lazy_polls = 32;
+
+	/* (Optional) Write-Clear the EC to Host Mailbox Register */
+	val = inb(data->addr + 1);
+	outb(val, data->addr + 1);
+
+	/* Set Mailbox Address Pointer to first location in Region 1 */
+	outb(0x00, data->addr + 2);
+	outb(0x80, data->addr + 3);
+
+	/* Write Request Packet Header */
+	outb(0x02, data->addr + 4); /* Access Type: VREG read */
+	outb(0x01, data->addr + 5); /* # of Entries: 1 Byte (8-bit) */
+	outb(0x04, data->addr + 2); /* Mailbox AP to first data entry loc. */
+
+	/* Write Address field */
+	outb(reg & 0xff, data->addr + 6);
+	outb(reg >> 8, data->addr + 7);
+
+	/* Execute the Random Access Command */
+	outb(0x01, data->addr); /* Write 01h to the Host-to-EC register */
+
+	/* EM Interface Polling "Algorithm" */
+	for (i = 0; i < max_busy_polls + max_lazy_polls; i++) {
+		if (i >= max_busy_polls)
+			msleep(1);
+		/* Read Interrupt source Register */
+		val = inb(data->addr + 8);
+		/* Write Clear the interrupt source bits */
+		if (val)
+			outb(val, data->addr + 8);
+		/* Command Completed ? */
+		if (val & 0x01)
+			break;
+	}
+	if (i == max_busy_polls + max_lazy_polls) {
+		pr_err("Max retries exceeded reading virtual "
+		       "register 0x%04hx (%d)\n", reg, 1);
+		return -EIO;
+	}
+
+	/*
+	 * According to SMSC we may need to retry this, but sofar I've always
+	 * seen this succeed in 1 try.
+	 */
+	for (i = 0; i < max_busy_polls; i++) {
+		/* Read EC-to-Host Register */
+		val = inb(data->addr + 1);
+		/* Command Completed ? */
+		if (val == 0x01)
+			break;
+
+		if (i == 0)
+			pr_warn("EC reports: 0x%02x reading virtual register "
+				"0x%04hx\n", (unsigned int)val, reg);
+	}
+	if (i == max_busy_polls) {
+		pr_err("Max retries exceeded reading virtual "
+		       "register 0x%04hx (%d)\n", reg, 2);
+		return -EIO;
+	}
+
+	/*
+	 * According to the SMSC app note we should now do:
+	 *
+	 * Set Mailbox Address Pointer to first location in Region 1 *
+	 * outb(0x00, data->addr + 2);
+	 * outb(0x80, data->addr + 3);
+	 *
+	 * But if we do that things don't work, so let's not.
+	 */
+
+	/* Read Data from Mailbox */
+	return inb(data->addr + 4);
+}
+
+static int sch5627_read_virtual_reg16(struct sch5627_data *data, u16 reg)
+{
+	int lsb, msb;
+
+	/* Read LSB first, this will cause the matching MSB to be latched */
+	lsb = sch5627_read_virtual_reg(data, reg);
+	if (lsb < 0)
+		return lsb;
+
+	msb = sch5627_read_virtual_reg(data, reg + 1);
+	if (msb < 0)
+		return msb;
+
+	return lsb | (msb << 8);
+}
+
+static int sch5627_read_virtual_reg12(struct sch5627_data *data, u16 msb_reg,
+				      u16 lsn_reg, int high_nibble)
+{
+	int msb, lsn;
+
+	/* Read MSB first, this will cause the matching LSN to be latched */
+	msb = sch5627_read_virtual_reg(data, msb_reg);
+	if (msb < 0)
+		return msb;
+
+	lsn = sch5627_read_virtual_reg(data, lsn_reg);
+	if (lsn < 0)
+		return lsn;
+
+	if (high_nibble)
+		return (msb << 4) | (lsn >> 4);
+	else
+		return (msb << 4) | (lsn & 0x0f);
+}
+
+static struct sch5627_data *sch5627_update_device(struct device *dev)
+{
+	struct sch5627_data *data = dev_get_drvdata(dev);
+	struct sch5627_data *ret = data;
+	int i, val;
+
+	mutex_lock(&data->update_lock);
+
+	/* Cache the values for 1 second */
+	if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
+		for (i = 0; i < SCH5627_NO_TEMPS; i++) {
+			val = sch5627_read_virtual_reg12(data,
+				SCH5627_REG_TEMP_MSB[i],
+				SCH5627_REG_TEMP_LSN[i],
+				SCH5627_REG_TEMP_HIGH_NIBBLE[i]);
+			if (unlikely(val < 0)) {
+				ret = ERR_PTR(val);
+				goto abort;
+			}
+			data->temp[i] = val;
+		}
+
+		for (i = 0; i < SCH5627_NO_FANS; i++) {
+			val = sch5627_read_virtual_reg16(data,
+							 SCH5627_REG_FAN[i]);
+			if (unlikely(val < 0)) {
+				ret = ERR_PTR(val);
+				goto abort;
+			}
+			data->fan[i] = val;
+		}
+
+		for (i = 0; i < SCH5627_NO_IN; i++) {
+			val = sch5627_read_virtual_reg12(data,
+				SCH5627_REG_IN_MSB[i],
+				SCH5627_REG_IN_LSN[i],
+				SCH5627_REG_IN_HIGH_NIBBLE[i]);
+			if (unlikely(val < 0)) {
+				ret = ERR_PTR(val);
+				goto abort;
+			}
+			data->in[i] = val;
+		}
+
+		data->last_updated = jiffies;
+		data->valid = 1;
+	}
+abort:
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static int __devinit sch5627_read_limits(struct sch5627_data *data)
+{
+	int i, val;
+
+	for (i = 0; i < SCH5627_NO_TEMPS; i++) {
+		/*
+		 * Note what SMSC calls ABS, is what lm_sensors calls max
+		 * (aka high), and HIGH is what lm_sensors calls crit.
+		 */
+		val = sch5627_read_virtual_reg(data, SCH5627_REG_TEMP_ABS[i]);
+		if (val < 0)
+			return val;
+		data->temp_max[i] = val;
+
+		val = sch5627_read_virtual_reg(data, SCH5627_REG_TEMP_HIGH[i]);
+		if (val < 0)
+			return val;
+		data->temp_crit[i] = val;
+	}
+	for (i = 0; i < SCH5627_NO_FANS; i++) {
+		val = sch5627_read_virtual_reg16(data, SCH5627_REG_FAN_MIN[i]);
+		if (val < 0)
+			return val;
+		data->fan_min[i] = val;
+	}
+
+	return 0;
+}
+
+static int reg_to_temp(u16 reg)
+{
+	return (reg * 625) / 10 - 64000;
+}
+
+static int reg_to_temp_limit(u8 reg)
+{
+	return (reg - 64) * 1000;
+}
+
+static int reg_to_rpm(u16 reg)
+{
+	if (reg == 0)
+		return -EIO;
+	if (reg == 0xffff)
+		return 0;
+
+	return 5400540 / reg;
+}
+
+static ssize_t show_name(struct device *dev, struct device_attribute *devattr,
+	char *buf)
+{
+	return snprintf(buf, PAGE_SIZE, "%s\n", DEVNAME);
+}
+
+static ssize_t show_temp(struct device *dev, struct device_attribute
+	*devattr, char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct sch5627_data *data = sch5627_update_device(dev);
+	int val;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	val = reg_to_temp(data->temp[attr->index]);
+	return snprintf(buf, PAGE_SIZE, "%d\n", val);
+}
+
+static ssize_t show_temp_fault(struct device *dev, struct device_attribute
+	*devattr, char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct sch5627_data *data = sch5627_update_device(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", data->temp[attr->index] == 0);
+}
+
+static ssize_t show_temp_max(struct device *dev, struct device_attribute
+	*devattr, char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct sch5627_data *data = dev_get_drvdata(dev);
+	int val;
+
+	val = reg_to_temp_limit(data->temp_max[attr->index]);
+	return snprintf(buf, PAGE_SIZE, "%d\n", val);
+}
+
+static ssize_t show_temp_crit(struct device *dev, struct device_attribute
+	*devattr, char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct sch5627_data *data = dev_get_drvdata(dev);
+	int val;
+
+	val = reg_to_temp_limit(data->temp_crit[attr->index]);
+	return snprintf(buf, PAGE_SIZE, "%d\n", val);
+}
+
+static ssize_t show_fan(struct device *dev, struct device_attribute
+	*devattr, char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct sch5627_data *data = sch5627_update_device(dev);
+	int val;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	val = reg_to_rpm(data->fan[attr->index]);
+	if (val < 0)
+		return val;
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", val);
+}
+
+static ssize_t show_fan_fault(struct device *dev, struct device_attribute
+	*devattr, char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct sch5627_data *data = sch5627_update_device(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	return snprintf(buf, PAGE_SIZE, "%d\n",
+			data->fan[attr->index] == 0xffff);
+}
+
+static ssize_t show_fan_min(struct device *dev, struct device_attribute
+	*devattr, char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct sch5627_data *data = dev_get_drvdata(dev);
+	int val = reg_to_rpm(data->fan_min[attr->index]);
+	if (val < 0)
+		return val;
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", val);
+}
+
+static ssize_t show_in(struct device *dev, struct device_attribute
+	*devattr, char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct sch5627_data *data = sch5627_update_device(dev);
+	int val;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	val = DIV_ROUND_CLOSEST(
+		data->in[attr->index] * SCH5627_REG_IN_FACTOR[attr->index],
+		10000);
+	return snprintf(buf, PAGE_SIZE, "%d\n", val);
+}
+
+static ssize_t show_in_label(struct device *dev, struct device_attribute
+	*devattr, char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+
+	return snprintf(buf, PAGE_SIZE, "%s\n",
+			SCH5627_IN_LABELS[attr->index]);
+}
+
+static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_temp, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp3_input, S_IRUGO, show_temp, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp4_input, S_IRUGO, show_temp, NULL, 3);
+static SENSOR_DEVICE_ATTR(temp5_input, S_IRUGO, show_temp, NULL, 4);
+static SENSOR_DEVICE_ATTR(temp6_input, S_IRUGO, show_temp, NULL, 5);
+static SENSOR_DEVICE_ATTR(temp7_input, S_IRUGO, show_temp, NULL, 6);
+static SENSOR_DEVICE_ATTR(temp8_input, S_IRUGO, show_temp, NULL, 7);
+static SENSOR_DEVICE_ATTR(temp1_fault, S_IRUGO, show_temp_fault, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_temp_fault, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_temp_fault, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp4_fault, S_IRUGO, show_temp_fault, NULL, 3);
+static SENSOR_DEVICE_ATTR(temp5_fault, S_IRUGO, show_temp_fault, NULL, 4);
+static SENSOR_DEVICE_ATTR(temp6_fault, S_IRUGO, show_temp_fault, NULL, 5);
+static SENSOR_DEVICE_ATTR(temp7_fault, S_IRUGO, show_temp_fault, NULL, 6);
+static SENSOR_DEVICE_ATTR(temp8_fault, S_IRUGO, show_temp_fault, NULL, 7);
+static SENSOR_DEVICE_ATTR(temp1_max, S_IRUGO, show_temp_max, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp2_max, S_IRUGO, show_temp_max, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp3_max, S_IRUGO, show_temp_max, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp4_max, S_IRUGO, show_temp_max, NULL, 3);
+static SENSOR_DEVICE_ATTR(temp5_max, S_IRUGO, show_temp_max, NULL, 4);
+static SENSOR_DEVICE_ATTR(temp6_max, S_IRUGO, show_temp_max, NULL, 5);
+static SENSOR_DEVICE_ATTR(temp7_max, S_IRUGO, show_temp_max, NULL, 6);
+static SENSOR_DEVICE_ATTR(temp8_max, S_IRUGO, show_temp_max, NULL, 7);
+static SENSOR_DEVICE_ATTR(temp1_crit, S_IRUGO, show_temp_crit, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp2_crit, S_IRUGO, show_temp_crit, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp3_crit, S_IRUGO, show_temp_crit, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp4_crit, S_IRUGO, show_temp_crit, NULL, 3);
+static SENSOR_DEVICE_ATTR(temp5_crit, S_IRUGO, show_temp_crit, NULL, 4);
+static SENSOR_DEVICE_ATTR(temp6_crit, S_IRUGO, show_temp_crit, NULL, 5);
+static SENSOR_DEVICE_ATTR(temp7_crit, S_IRUGO, show_temp_crit, NULL, 6);
+static SENSOR_DEVICE_ATTR(temp8_crit, S_IRUGO, show_temp_crit, NULL, 7);
+
+static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_fan, NULL, 0);
+static SENSOR_DEVICE_ATTR(fan2_input, S_IRUGO, show_fan, NULL, 1);
+static SENSOR_DEVICE_ATTR(fan3_input, S_IRUGO, show_fan, NULL, 2);
+static SENSOR_DEVICE_ATTR(fan4_input, S_IRUGO, show_fan, NULL, 3);
+static SENSOR_DEVICE_ATTR(fan1_fault, S_IRUGO, show_fan_fault, NULL, 0);
+static SENSOR_DEVICE_ATTR(fan2_fault, S_IRUGO, show_fan_fault, NULL, 1);
+static SENSOR_DEVICE_ATTR(fan3_fault, S_IRUGO, show_fan_fault, NULL, 2);
+static SENSOR_DEVICE_ATTR(fan4_fault, S_IRUGO, show_fan_fault, NULL, 3);
+static SENSOR_DEVICE_ATTR(fan1_min, S_IRUGO, show_fan_min, NULL, 0);
+static SENSOR_DEVICE_ATTR(fan2_min, S_IRUGO, show_fan_min, NULL, 1);
+static SENSOR_DEVICE_ATTR(fan3_min, S_IRUGO, show_fan_min, NULL, 2);
+static SENSOR_DEVICE_ATTR(fan4_min, S_IRUGO, show_fan_min, NULL, 3);
+
+static SENSOR_DEVICE_ATTR(in0_input, S_IRUGO, show_in, NULL, 0);
+static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, show_in, NULL, 1);
+static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, show_in, NULL, 2);
+static SENSOR_DEVICE_ATTR(in3_input, S_IRUGO, show_in, NULL, 3);
+static SENSOR_DEVICE_ATTR(in4_input, S_IRUGO, show_in, NULL, 4);
+static SENSOR_DEVICE_ATTR(in0_label, S_IRUGO, show_in_label, NULL, 0);
+static SENSOR_DEVICE_ATTR(in1_label, S_IRUGO, show_in_label, NULL, 1);
+static SENSOR_DEVICE_ATTR(in2_label, S_IRUGO, show_in_label, NULL, 2);
+static SENSOR_DEVICE_ATTR(in3_label, S_IRUGO, show_in_label, NULL, 3);
+
+static struct attribute *sch5627_attributes[] = {
+	&dev_attr_name.attr,
+
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	&sensor_dev_attr_temp2_input.dev_attr.attr,
+	&sensor_dev_attr_temp3_input.dev_attr.attr,
+	&sensor_dev_attr_temp4_input.dev_attr.attr,
+	&sensor_dev_attr_temp5_input.dev_attr.attr,
+	&sensor_dev_attr_temp6_input.dev_attr.attr,
+	&sensor_dev_attr_temp7_input.dev_attr.attr,
+	&sensor_dev_attr_temp8_input.dev_attr.attr,
+	&sensor_dev_attr_temp1_fault.dev_attr.attr,
+	&sensor_dev_attr_temp2_fault.dev_attr.attr,
+	&sensor_dev_attr_temp3_fault.dev_attr.attr,
+	&sensor_dev_attr_temp4_fault.dev_attr.attr,
+	&sensor_dev_attr_temp5_fault.dev_attr.attr,
+	&sensor_dev_attr_temp6_fault.dev_attr.attr,
+	&sensor_dev_attr_temp7_fault.dev_attr.attr,
+	&sensor_dev_attr_temp8_fault.dev_attr.attr,
+	&sensor_dev_attr_temp1_max.dev_attr.attr,
+	&sensor_dev_attr_temp2_max.dev_attr.attr,
+	&sensor_dev_attr_temp3_max.dev_attr.attr,
+	&sensor_dev_attr_temp4_max.dev_attr.attr,
+	&sensor_dev_attr_temp5_max.dev_attr.attr,
+	&sensor_dev_attr_temp6_max.dev_attr.attr,
+	&sensor_dev_attr_temp7_max.dev_attr.attr,
+	&sensor_dev_attr_temp8_max.dev_attr.attr,
+	&sensor_dev_attr_temp1_crit.dev_attr.attr,
+	&sensor_dev_attr_temp2_crit.dev_attr.attr,
+	&sensor_dev_attr_temp3_crit.dev_attr.attr,
+	&sensor_dev_attr_temp4_crit.dev_attr.attr,
+	&sensor_dev_attr_temp5_crit.dev_attr.attr,
+	&sensor_dev_attr_temp6_crit.dev_attr.attr,
+	&sensor_dev_attr_temp7_crit.dev_attr.attr,
+	&sensor_dev_attr_temp8_crit.dev_attr.attr,
+
+	&sensor_dev_attr_fan1_input.dev_attr.attr,
+	&sensor_dev_attr_fan2_input.dev_attr.attr,
+	&sensor_dev_attr_fan3_input.dev_attr.attr,
+	&sensor_dev_attr_fan4_input.dev_attr.attr,
+	&sensor_dev_attr_fan1_fault.dev_attr.attr,
+	&sensor_dev_attr_fan2_fault.dev_attr.attr,
+	&sensor_dev_attr_fan3_fault.dev_attr.attr,
+	&sensor_dev_attr_fan4_fault.dev_attr.attr,
+	&sensor_dev_attr_fan1_min.dev_attr.attr,
+	&sensor_dev_attr_fan2_min.dev_attr.attr,
+	&sensor_dev_attr_fan3_min.dev_attr.attr,
+	&sensor_dev_attr_fan4_min.dev_attr.attr,
+
+	&sensor_dev_attr_in0_input.dev_attr.attr,
+	&sensor_dev_attr_in1_input.dev_attr.attr,
+	&sensor_dev_attr_in2_input.dev_attr.attr,
+	&sensor_dev_attr_in3_input.dev_attr.attr,
+	&sensor_dev_attr_in4_input.dev_attr.attr,
+	&sensor_dev_attr_in0_label.dev_attr.attr,
+	&sensor_dev_attr_in1_label.dev_attr.attr,
+	&sensor_dev_attr_in2_label.dev_attr.attr,
+	&sensor_dev_attr_in3_label.dev_attr.attr,
+	/* No in4_label as in4 is a generic input pin */
+
+	NULL
+};
+
+static const struct attribute_group sch5627_group = {
+	.attrs = sch5627_attributes,
+};
+
+static int sch5627_remove(struct platform_device *pdev)
+{
+	struct sch5627_data *data = platform_get_drvdata(pdev);
+
+	if (data->hwmon_dev)
+		hwmon_device_unregister(data->hwmon_dev);
+
+	sysfs_remove_group(&pdev->dev.kobj, &sch5627_group);
+	platform_set_drvdata(pdev, NULL);
+	kfree(data);
+
+	return 0;
+}
+
+static int __devinit sch5627_probe(struct platform_device *pdev)
+{
+	struct sch5627_data *data;
+	int err, build_code, build_id, hwmon_rev, val;
+
+	data = kzalloc(sizeof(struct sch5627_data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->addr = platform_get_resource(pdev, IORESOURCE_IO, 0)->start;
+	mutex_init(&data->update_lock);
+	platform_set_drvdata(pdev, data);
+
+	val = sch5627_read_virtual_reg(data, SCH5627_REG_HWMON_ID);
+	if (val < 0) {
+		err = val;
+		goto error;
+	}
+	if (val != SCH5627_HWMON_ID) {
+		pr_err("invalid %s id: 0x%02X (expected 0x%02X)\n", "hwmon",
+		       val, SCH5627_HWMON_ID);
+		err = -ENODEV;
+		goto error;
+	}
+
+	val = sch5627_read_virtual_reg(data, SCH5627_REG_COMPANY_ID);
+	if (val < 0) {
+		err = val;
+		goto error;
+	}
+	if (val != SCH5627_COMPANY_ID) {
+		pr_err("invalid %s id: 0x%02X (expected 0x%02X)\n", "company",
+		       val, SCH5627_COMPANY_ID);
+		err = -ENODEV;
+		goto error;
+	}
+
+	val = sch5627_read_virtual_reg(data, SCH5627_REG_PRIMARY_ID);
+	if (val < 0) {
+		err = val;
+		goto error;
+	}
+	if (val != SCH5627_PRIMARY_ID) {
+		pr_err("invalid %s id: 0x%02X (expected 0x%02X)\n", "primary",
+		       val, SCH5627_PRIMARY_ID);
+		err = -ENODEV;
+		goto error;
+	}
+
+	build_code = sch5627_read_virtual_reg(data, SCH5627_REG_BUILD_CODE);
+	if (build_code < 0) {
+		err = build_code;
+		goto error;
+	}
+
+	build_id = sch5627_read_virtual_reg16(data, SCH5627_REG_BUILD_ID);
+	if (build_id < 0) {
+		err = build_id;
+		goto error;
+	}
+
+	hwmon_rev = sch5627_read_virtual_reg(data, SCH5627_REG_HWMON_REV);
+	if (hwmon_rev < 0) {
+		err = hwmon_rev;
+		goto error;
+	}
+
+	val = sch5627_read_virtual_reg(data, SCH5627_REG_CTRL);
+	if (val < 0) {
+		err = val;
+		goto error;
+	}
+	if (!(val & 0x01)) {
+		pr_err("hardware monitoring not enabled\n");
+		err = -ENODEV;
+		goto error;
+	}
+
+	/*
+	 * Read limits, we do this only once as reading a register on
+	 * the sch5627 is quite expensive (and they don't change).
+	 */
+	err = sch5627_read_limits(data);
+	if (err)
+		goto error;
+
+	pr_info("firmware build: code 0x%02X, id 0x%04X, hwmon: rev 0x%02X\n",
+		build_code, build_id, hwmon_rev);
+
+	/* Register sysfs interface files */
+	err = sysfs_create_group(&pdev->dev.kobj, &sch5627_group);
+	if (err)
+		goto error;
+
+	data->hwmon_dev = hwmon_device_register(&pdev->dev);
+	if (IS_ERR(data->hwmon_dev)) {
+		err = PTR_ERR(data->hwmon_dev);
+		data->hwmon_dev = NULL;
+		goto error;
+	}
+
+	return 0;
+
+error:
+	sch5627_remove(pdev);
+	return err;
+}
+
+static int __init sch5627_find(int sioaddr, unsigned short *address)
+{
+	u8 devid;
+	int err = superio_enter(sioaddr);
+	if (err)
+		return err;
+
+	devid = superio_inb(sioaddr, SIO_REG_DEVID);
+	if (devid != SIO_SCH5627_ID) {
+		pr_debug("Unsupported device id: 0x%02x\n",
+			 (unsigned int)devid);
+		err = -ENODEV;
+		goto exit;
+	}
+
+	superio_select(sioaddr, SIO_SCH5627_EM_LD);
+
+	if (!(superio_inb(sioaddr, SIO_REG_ENABLE) & 0x01)) {
+		pr_warn("Device not activated\n");
+		err = -ENODEV;
+		goto exit;
+	}
+
+	/*
+	 * Warning the order of the low / high byte is the other way around
+	 * as on most other superio devices!!
+	 */
+	*address = superio_inb(sioaddr, SIO_REG_ADDR) |
+		   superio_inb(sioaddr, SIO_REG_ADDR + 1) << 8;
+	if (*address == 0) {
+		pr_warn("Base address not set\n");
+		err = -ENODEV;
+		goto exit;
+	}
+
+	pr_info("Found %s chip at %#hx\n", DEVNAME, *address);
+exit:
+	superio_exit(sioaddr);
+	return err;
+}
+
+static int __init sch5627_device_add(unsigned short address)
+{
+	struct resource res = {
+		.start	= address,
+		.end	= address + REGION_LENGTH - 1,
+		.flags	= IORESOURCE_IO,
+	};
+	int err;
+
+	sch5627_pdev = platform_device_alloc(DRVNAME, address);
+	if (!sch5627_pdev)
+		return -ENOMEM;
+
+	res.name = sch5627_pdev->name;
+	err = acpi_check_resource_conflict(&res);
+	if (err)
+		goto exit_device_put;
+
+	err = platform_device_add_resources(sch5627_pdev, &res, 1);
+	if (err) {
+		pr_err("Device resource addition failed\n");
+		goto exit_device_put;
+	}
+
+	err = platform_device_add(sch5627_pdev);
+	if (err) {
+		pr_err("Device addition failed\n");
+		goto exit_device_put;
+	}
+
+	return 0;
+
+exit_device_put:
+	platform_device_put(sch5627_pdev);
+
+	return err;
+}
+
+static struct platform_driver sch5627_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= DRVNAME,
+	},
+	.probe		= sch5627_probe,
+	.remove		= sch5627_remove,
+};
+
+static int __init sch5627_init(void)
+{
+	int err = -ENODEV;
+	unsigned short address;
+
+	if (sch5627_find(0x4e, &address) && sch5627_find(0x2e, &address))
+		goto exit;
+
+	err = platform_driver_register(&sch5627_driver);
+	if (err)
+		goto exit;
+
+	err = sch5627_device_add(address);
+	if (err)
+		goto exit_driver;
+
+	return 0;
+
+exit_driver:
+	platform_driver_unregister(&sch5627_driver);
+exit:
+	return err;
+}
+
+static void __exit sch5627_exit(void)
+{
+	platform_device_unregister(sch5627_pdev);
+	platform_driver_unregister(&sch5627_driver);
+}
+
+MODULE_DESCRIPTION("SMSC SCH5627 Hardware Monitoring Driver");
+MODULE_AUTHOR("Hans de Goede (hdegoede@redhat.com)");
+MODULE_LICENSE("GPL");
+
+module_init(sch5627_init);
+module_exit(sch5627_exit);
diff --git a/drivers/hwmon/sht15.c b/drivers/hwmon/sht15.c
index a610e78..1a9c32d 100644
--- a/drivers/hwmon/sht15.c
+++ b/drivers/hwmon/sht15.c
@@ -333,11 +333,11 @@
 
 	const int c1 = -4;
 	const int c2 = 40500; /* x 10 ^ -6 */
-	const int c3 = -2800; /* x10 ^ -9 */
+	const int c3 = -28; /* x 10 ^ -7 */
 
 	RHlinear = c1*1000
 		+ c2 * data->val_humid/1000
-		+ (data->val_humid * data->val_humid * c3)/1000000;
+		+ (data->val_humid * data->val_humid * c3) / 10000;
 	return (temp - 25000) * (10000 + 80 * data->val_humid)
 		/ 1000000 + RHlinear;
 }
@@ -610,7 +610,7 @@
 	struct sht15_data *data = platform_get_drvdata(pdev);
 
 	/* Make sure any reads from the device are done and
-	 * prevent new ones beginnning */
+	 * prevent new ones from beginning */
 	mutex_lock(&data->read_lock);
 	hwmon_device_unregister(data->hwmon_dev);
 	sysfs_remove_group(&pdev->dev.kobj, &sht15_attr_group);
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index b7d5ef2..203500d 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -2,6 +2,14 @@
 # Misc strange devices
 #
 
+# This one has to live outside of the MISC_DEVICES conditional,
+# because it may be selected by drivers/platform/x86/hp_accel.
+config SENSORS_LIS3LV02D
+	tristate
+	depends on INPUT
+	select INPUT_POLLDEV
+	default n
+
 menuconfig MISC_DEVICES
 	bool "Misc devices"
 	---help---
@@ -462,5 +470,6 @@
 source "drivers/misc/cb710/Kconfig"
 source "drivers/misc/iwmc3200top/Kconfig"
 source "drivers/misc/ti-st/Kconfig"
+source "drivers/misc/lis3lv02d/Kconfig"
 
 endif # MISC_DEVICES
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index 98009cc..804f421 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -42,3 +42,4 @@
 obj-$(CONFIG_PCH_PHUB)		+= pch_phub.o
 obj-y				+= ti-st/
 obj-$(CONFIG_AB8500_PWM)	+= ab8500-pwm.o
+obj-y				+= lis3lv02d/
diff --git a/drivers/misc/lis3lv02d/Kconfig b/drivers/misc/lis3lv02d/Kconfig
new file mode 100644
index 0000000..8f474e6
--- /dev/null
+++ b/drivers/misc/lis3lv02d/Kconfig
@@ -0,0 +1,37 @@
+#
+# STMicroelectonics LIS3LV02D and similar accelerometers
+#
+
+config SENSORS_LIS3_SPI
+	tristate "STMicroeletronics LIS3LV02Dx three-axis digital accelerometer (SPI)"
+	depends on !ACPI && SPI_MASTER && INPUT
+	select SENSORS_LIS3LV02D
+	default n
+	help
+	  This driver provides support for the LIS3LV02Dx accelerometer connected
+	  via SPI. The accelerometer data is readable via
+	  /sys/devices/platform/lis3lv02d.
+
+	  This driver also provides an absolute input class device, allowing
+	  the laptop to act as a pinball machine-esque joystick.
+
+	  This driver can also be built as modules.  If so, the core module
+	  will be called lis3lv02d and a specific module for the SPI transport
+	  is called lis3lv02d_spi.
+
+config SENSORS_LIS3_I2C
+	tristate "STMicroeletronics LIS3LV02Dx three-axis digital accelerometer (I2C)"
+	depends on I2C && INPUT
+	select SENSORS_LIS3LV02D
+	default n
+	help
+	  This driver provides support for the LIS3LV02Dx accelerometer connected
+	  via I2C. The accelerometer data is readable via
+	  /sys/devices/platform/lis3lv02d.
+
+	  This driver also provides an absolute input class device, allowing
+	  the device to act as a pinball machine-esque joystick.
+
+	  This driver can also be built as modules.  If so, the core module
+	  will be called lis3lv02d and a specific module for the I2C transport
+	  is called lis3lv02d_i2c.
diff --git a/drivers/misc/lis3lv02d/Makefile b/drivers/misc/lis3lv02d/Makefile
new file mode 100644
index 0000000..4bf58b1
--- /dev/null
+++ b/drivers/misc/lis3lv02d/Makefile
@@ -0,0 +1,7 @@
+#
+# STMicroelectonics LIS3LV02D and similar accelerometers
+#
+
+obj-$(CONFIG_SENSORS_LIS3LV02D) += lis3lv02d.o
+obj-$(CONFIG_SENSORS_LIS3_SPI)	+= lis3lv02d_spi.o
+obj-$(CONFIG_SENSORS_LIS3_I2C)	+= lis3lv02d_i2c.o
diff --git a/drivers/hwmon/lis3lv02d.c b/drivers/misc/lis3lv02d/lis3lv02d.c
similarity index 99%
rename from drivers/hwmon/lis3lv02d.c
rename to drivers/misc/lis3lv02d/lis3lv02d.c
index d805e8e..b928bc1 100644
--- a/drivers/hwmon/lis3lv02d.c
+++ b/drivers/misc/lis3lv02d/lis3lv02d.c
@@ -38,7 +38,7 @@
 #include <linux/uaccess.h>
 #include <linux/miscdevice.h>
 #include <linux/pm_runtime.h>
-#include <asm/atomic.h>
+#include <linux/atomic.h>
 #include "lis3lv02d.h"
 
 #define DRIVER_NAME     "lis3lv02d"
@@ -88,7 +88,6 @@
 struct lis3lv02d lis3_dev = {
 	.misc_wait   = __WAIT_QUEUE_HEAD_INITIALIZER(lis3_dev.misc_wait),
 };
-
 EXPORT_SYMBOL_GPL(lis3_dev);
 
 /* just like param_set_int() but does sanity-check so that it won't point
diff --git a/drivers/hwmon/lis3lv02d.h b/drivers/misc/lis3lv02d/lis3lv02d.h
similarity index 100%
rename from drivers/hwmon/lis3lv02d.h
rename to drivers/misc/lis3lv02d/lis3lv02d.h
diff --git a/drivers/hwmon/lis3lv02d_i2c.c b/drivers/misc/lis3lv02d/lis3lv02d_i2c.c
similarity index 99%
rename from drivers/hwmon/lis3lv02d_i2c.c
rename to drivers/misc/lis3lv02d/lis3lv02d_i2c.c
index 8853afc..b20dfb4 100644
--- a/drivers/hwmon/lis3lv02d_i2c.c
+++ b/drivers/misc/lis3lv02d/lis3lv02d_i2c.c
@@ -33,7 +33,7 @@
 #include <linux/delay.h>
 #include "lis3lv02d.h"
 
-#define DRV_NAME 	"lis3lv02d_i2c"
+#define DRV_NAME	"lis3lv02d_i2c"
 
 static const char reg_vdd[]    = "Vdd";
 static const char reg_vdd_io[] = "Vdd_IO";
diff --git a/drivers/hwmon/lis3lv02d_spi.c b/drivers/misc/lis3lv02d/lis3lv02d_spi.c
similarity index 100%
rename from drivers/hwmon/lis3lv02d_spi.c
rename to drivers/misc/lis3lv02d/lis3lv02d_spi.c
diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig
index a59af5b..222dfb7 100644
--- a/drivers/platform/x86/Kconfig
+++ b/drivers/platform/x86/Kconfig
@@ -138,6 +138,24 @@
 	  This is a driver for the WMI extensions (wireless and bluetooth power
 	  control) of the HP Compaq TC1100 tablet.
 
+config HP_ACCEL
+	tristate "HP laptop accelerometer"
+	depends on INPUT && ACPI
+	select SENSORS_LIS3LV02D
+	select NEW_LEDS
+	select LEDS_CLASS
+	help
+	  This driver provides support for the "Mobile Data Protection System 3D"
+	  or "3D DriveGuard" feature of HP laptops. On such systems the driver
+	  should load automatically (via ACPI alias).
+
+	  Support for a led indicating disk protection will be provided as
+	  hp::hddprotect. For more information on the feature, refer to
+	  Documentation/hwmon/lis3lv02d.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called hp_accel.
+
 config HP_WMI
 	tristate "HP WMI extras"
 	depends on ACPI_WMI
diff --git a/drivers/platform/x86/Makefile b/drivers/platform/x86/Makefile
index 4ec4ff8..299aefb 100644
--- a/drivers/platform/x86/Makefile
+++ b/drivers/platform/x86/Makefile
@@ -12,6 +12,7 @@
 obj-$(CONFIG_DELL_WMI)		+= dell-wmi.o
 obj-$(CONFIG_ACER_WMI)		+= acer-wmi.o
 obj-$(CONFIG_ACERHDF)		+= acerhdf.o
+obj-$(CONFIG_HP_ACCEL)		+= hp_accel.o
 obj-$(CONFIG_HP_WMI)		+= hp-wmi.o
 obj-$(CONFIG_TC1100_WMI)	+= tc1100-wmi.o
 obj-$(CONFIG_SONY_LAPTOP)	+= sony-laptop.o
diff --git a/drivers/hwmon/hp_accel.c b/drivers/platform/x86/hp_accel.c
similarity index 98%
rename from drivers/hwmon/hp_accel.c
rename to drivers/platform/x86/hp_accel.c
index 3d21fa2..1b52d00 100644
--- a/drivers/hwmon/hp_accel.c
+++ b/drivers/platform/x86/hp_accel.c
@@ -35,11 +35,11 @@
 #include <linux/freezer.h>
 #include <linux/uaccess.h>
 #include <linux/leds.h>
+#include <linux/atomic.h>
 #include <acpi/acpi_drivers.h>
-#include <asm/atomic.h>
-#include "lis3lv02d.h"
+#include "../../misc/lis3lv02d/lis3lv02d.h"
 
-#define DRIVER_NAME     "lis3lv02d"
+#define DRIVER_NAME     "hp_accel"
 #define ACPI_MDPS_CLASS "accelerometer"
 
 /* Delayed LEDs infrastructure ------------------------------------ */
@@ -402,4 +402,3 @@
 
 module_init(lis3lv02d_init_module);
 module_exit(lis3lv02d_exit_module);
-
diff --git a/include/linux/i2c/ads1015.h b/include/linux/i2c/ads1015.h
new file mode 100644
index 0000000..d5aa2a0
--- /dev/null
+++ b/include/linux/i2c/ads1015.h
@@ -0,0 +1,36 @@
+/*
+ * Platform Data for ADS1015 12-bit 4-input ADC
+ * (C) Copyright 2010
+ * Dirk Eibach, Guntermann & Drunck GmbH <eibach@gdsys.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef LINUX_ADS1015_H
+#define LINUX_ADS1015_H
+
+#define ADS1015_CHANNELS 8
+
+struct ads1015_channel_data {
+	bool enabled;
+	unsigned int pga;
+	unsigned int data_rate;
+};
+
+struct ads1015_platform_data {
+	struct ads1015_channel_data channel_data[ADS1015_CHANNELS];
+};
+
+#endif /* LINUX_ADS1015_H */