diff --git a/MAINTAINERS b/MAINTAINERS
index 560ecce..b64776c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5658,7 +5658,8 @@
 F:	arch/arm/mach-s3c2410/bast-irq.c
 
 TI DAVINCI MACHINE SUPPORT
-M:	Kevin Hilman <khilman@deeprootsystems.com>
+M:	Sekhar Nori <nsekhar@ti.com>
+M:	Kevin Hilman <khilman@ti.com>
 L:	davinci-linux-open-source@linux.davincidsp.com (subscribers-only)
 Q:	http://patchwork.kernel.org/project/linux-davinci/list/
 S:	Supported
diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c
index b52a3a1..8bc3701 100644
--- a/arch/arm/mach-davinci/board-da830-evm.c
+++ b/arch/arm/mach-davinci/board-da830-evm.c
@@ -20,6 +20,8 @@
 #include <linux/i2c/at24.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -30,6 +32,7 @@
 #include <mach/da8xx.h>
 #include <mach/usb.h>
 #include <mach/aemif.h>
+#include <mach/spi.h>
 
 #define DA830_EVM_PHY_ID		""
 /*
@@ -534,6 +537,64 @@
 	},
 };
 
+static struct mtd_partition da830evm_spiflash_part[] = {
+	[0] = {
+		.name = "DSP-UBL",
+		.offset = 0,
+		.size = SZ_8K,
+		.mask_flags = MTD_WRITEABLE,
+	},
+	[1] = {
+		.name = "ARM-UBL",
+		.offset = MTDPART_OFS_APPEND,
+		.size = SZ_16K + SZ_8K,
+		.mask_flags = MTD_WRITEABLE,
+	},
+	[2] = {
+		.name = "U-Boot",
+		.offset = MTDPART_OFS_APPEND,
+		.size = SZ_256K - SZ_32K,
+		.mask_flags = MTD_WRITEABLE,
+	},
+	[3] = {
+		.name = "U-Boot-Environment",
+		.offset = MTDPART_OFS_APPEND,
+		.size = SZ_16K,
+		.mask_flags = 0,
+	},
+	[4] = {
+		.name = "Kernel",
+		.offset = MTDPART_OFS_APPEND,
+		.size = MTDPART_SIZ_FULL,
+		.mask_flags = 0,
+	},
+};
+
+static struct flash_platform_data da830evm_spiflash_data = {
+	.name		= "m25p80",
+	.parts		= da830evm_spiflash_part,
+	.nr_parts	= ARRAY_SIZE(da830evm_spiflash_part),
+	.type		= "w25x32",
+};
+
+static struct davinci_spi_config da830evm_spiflash_cfg = {
+	.io_type	= SPI_IO_TYPE_DMA,
+	.c2tdelay	= 8,
+	.t2cdelay	= 8,
+};
+
+static struct spi_board_info da830evm_spi_info[] = {
+	{
+		.modalias		= "m25p80",
+		.platform_data		= &da830evm_spiflash_data,
+		.controller_data	= &da830evm_spiflash_cfg,
+		.mode			= SPI_MODE_0,
+		.max_speed_hz		= 30000000,
+		.bus_num		= 0,
+		.chip_select		= 0,
+	},
+};
+
 static __init void da830_evm_init(void)
 {
 	struct davinci_soc_info *soc_info = &davinci_soc_info;
@@ -590,6 +651,12 @@
 	ret = da8xx_register_rtc();
 	if (ret)
 		pr_warning("da830_evm_init: rtc setup failed: %d\n", ret);
+
+	ret = da8xx_register_spi(0, da830evm_spi_info,
+				 ARRAY_SIZE(da830evm_spi_info));
+	if (ret)
+		pr_warning("da830_evm_init: spi 0 registration failed: %d\n",
+			   ret);
 }
 
 #ifdef CONFIG_SERIAL_8250_CONSOLE
diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
index b01fb2a..a7b41bf 100644
--- a/arch/arm/mach-davinci/board-da850-evm.c
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -29,6 +29,8 @@
 #include <linux/regulator/machine.h>
 #include <linux/regulator/tps6507x.h>
 #include <linux/input/tps6507x-ts.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -38,6 +40,7 @@
 #include <mach/nand.h>
 #include <mach/mux.h>
 #include <mach/aemif.h>
+#include <mach/spi.h>
 
 #define DA850_EVM_PHY_ID		"0:00"
 #define DA850_LCD_PWR_PIN		GPIO_TO_PIN(2, 8)
@@ -48,6 +51,70 @@
 
 #define DA850_MII_MDIO_CLKEN_PIN	GPIO_TO_PIN(2, 6)
 
+static struct mtd_partition da850evm_spiflash_part[] = {
+	[0] = {
+		.name = "UBL",
+		.offset = 0,
+		.size = SZ_64K,
+		.mask_flags = MTD_WRITEABLE,
+	},
+	[1] = {
+		.name = "U-Boot",
+		.offset = MTDPART_OFS_APPEND,
+		.size = SZ_512K,
+		.mask_flags = MTD_WRITEABLE,
+	},
+	[2] = {
+		.name = "U-Boot-Env",
+		.offset = MTDPART_OFS_APPEND,
+		.size = SZ_64K,
+		.mask_flags = MTD_WRITEABLE,
+	},
+	[3] = {
+		.name = "Kernel",
+		.offset = MTDPART_OFS_APPEND,
+		.size = SZ_2M + SZ_512K,
+		.mask_flags = 0,
+	},
+	[4] = {
+		.name = "Filesystem",
+		.offset = MTDPART_OFS_APPEND,
+		.size = SZ_4M,
+		.mask_flags = 0,
+	},
+	[5] = {
+		.name = "MAC-Address",
+		.offset = SZ_8M - SZ_64K,
+		.size = SZ_64K,
+		.mask_flags = MTD_WRITEABLE,
+	},
+};
+
+static struct flash_platform_data da850evm_spiflash_data = {
+	.name		= "m25p80",
+	.parts		= da850evm_spiflash_part,
+	.nr_parts	= ARRAY_SIZE(da850evm_spiflash_part),
+	.type		= "m25p64",
+};
+
+static struct davinci_spi_config da850evm_spiflash_cfg = {
+	.io_type	= SPI_IO_TYPE_DMA,
+	.c2tdelay	= 8,
+	.t2cdelay	= 8,
+};
+
+static struct spi_board_info da850evm_spi_info[] = {
+	{
+		.modalias		= "m25p80",
+		.platform_data		= &da850evm_spiflash_data,
+		.controller_data	= &da850evm_spiflash_cfg,
+		.mode			= SPI_MODE_0,
+		.max_speed_hz		= 30000000,
+		.bus_num		= 1,
+		.chip_select		= 0,
+	},
+};
+
 static struct mtd_partition da850_evm_norflash_partition[] = {
 	{
 		.name           = "bootloaders + env",
@@ -231,8 +298,6 @@
 	-1
 };
 
-static u32 ui_card_detected;
-
 #if defined(CONFIG_MMC_DAVINCI) || \
     defined(CONFIG_MMC_DAVINCI_MODULE)
 #define HAS_MMC 1
@@ -244,7 +309,7 @@
 {
 	int ret = 0;
 
-	if (ui_card_detected & !HAS_MMC) {
+	if (!HAS_MMC) {
 		ret = davinci_cfg_reg_list(da850_evm_nand_pins);
 		if (ret)
 			pr_warning("da850_evm_init: nand mux setup failed: "
@@ -394,7 +459,6 @@
 		goto exp_setup_keys_fail;
 	}
 
-	ui_card_detected = 1;
 	pr_info("DA850/OMAP-L138 EVM UI card detected\n");
 
 	da850_evm_setup_nor_nand();
@@ -664,6 +728,13 @@
 	.rxnumevt	= 1,
 };
 
+static const short da850_evm_mcasp_pins[] __initconst = {
+	DA850_AHCLKX, DA850_ACLKX, DA850_AFSX,
+	DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE,
+	DA850_AXR_11, DA850_AXR_12,
+	-1
+};
+
 static int da850_evm_mmc_get_ro(int index)
 {
 	return gpio_get_value(DA850_MMCSD_WP_PIN);
@@ -683,6 +754,13 @@
 	.version	= MMC_CTLR_VERSION_2,
 };
 
+static const short da850_evm_mmcsd0_pins[] __initconst = {
+	DA850_MMCSD0_DAT_0, DA850_MMCSD0_DAT_1, DA850_MMCSD0_DAT_2,
+	DA850_MMCSD0_DAT_3, DA850_MMCSD0_CLK, DA850_MMCSD0_CMD,
+	DA850_GPIO4_0, DA850_GPIO4_1,
+	-1
+};
+
 static void da850_panel_power_ctrl(int val)
 {
 	/* lcd backlight */
@@ -1070,7 +1148,7 @@
 				ret);
 
 	if (HAS_MMC) {
-		ret = davinci_cfg_reg_list(da850_mmcsd0_pins);
+		ret = davinci_cfg_reg_list(da850_evm_mmcsd0_pins);
 		if (ret)
 			pr_warning("da850_evm_init: mmcsd0 mux setup failed:"
 					" %d\n", ret);
@@ -1106,7 +1184,7 @@
 	__raw_writel(0, IO_ADDRESS(DA8XX_UART1_BASE) + 0x30);
 	__raw_writel(0, IO_ADDRESS(DA8XX_UART0_BASE) + 0x30);
 
-	ret = davinci_cfg_reg_list(da850_mcasp_pins);
+	ret = davinci_cfg_reg_list(da850_evm_mcasp_pins);
 	if (ret)
 		pr_warning("da850_evm_init: mcasp mux setup failed: %d\n",
 				ret);
@@ -1153,6 +1231,12 @@
 	if (ret)
 		pr_warning("da850_evm_init: suspend registration failed: %d\n",
 				ret);
+
+	ret = da8xx_register_spi(1, da850evm_spi_info,
+				 ARRAY_SIZE(da850evm_spi_info));
+	if (ret)
+		pr_warning("da850_evm_init: spi 1 registration failed: %d\n",
+				ret);
 }
 
 #ifdef CONFIG_SERIAL_8250_CONSOLE
diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c
index 0bb5f0c..2aa79c5 100644
--- a/arch/arm/mach-davinci/board-mityomapl138.c
+++ b/arch/arm/mach-davinci/board-mityomapl138.c
@@ -17,6 +17,8 @@
 #include <linux/i2c.h>
 #include <linux/i2c/at24.h>
 #include <linux/etherdevice.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -25,6 +27,7 @@
 #include <mach/da8xx.h>
 #include <mach/nand.h>
 #include <mach/mux.h>
+#include <mach/spi.h>
 
 #define MITYOMAPL138_PHY_ID		"0:03"
 
@@ -44,38 +47,109 @@
 
 static struct factory_config factory_config;
 
+struct part_no_info {
+	const char	*part_no;	/* part number string of interest */
+	int		max_freq;	/* khz */
+};
+
+static struct part_no_info mityomapl138_pn_info[] = {
+	{
+		.part_no	= "L138-C",
+		.max_freq	= 300000,
+	},
+	{
+		.part_no	= "L138-D",
+		.max_freq	= 375000,
+	},
+	{
+		.part_no	= "L138-F",
+		.max_freq	= 456000,
+	},
+	{
+		.part_no	= "1808-C",
+		.max_freq	= 300000,
+	},
+	{
+		.part_no	= "1808-D",
+		.max_freq	= 375000,
+	},
+	{
+		.part_no	= "1808-F",
+		.max_freq	= 456000,
+	},
+	{
+		.part_no	= "1810-D",
+		.max_freq	= 375000,
+	},
+};
+
+#ifdef CONFIG_CPU_FREQ
+static void mityomapl138_cpufreq_init(const char *partnum)
+{
+	int i, ret;
+
+	for (i = 0; partnum && i < ARRAY_SIZE(mityomapl138_pn_info); i++) {
+		/*
+		 * the part number has additional characters beyond what is
+		 * stored in the table.  This information is not needed for
+		 * determining the speed grade, and would require several
+		 * more table entries.  Only check the first N characters
+		 * for a match.
+		 */
+		if (!strncmp(partnum, mityomapl138_pn_info[i].part_no,
+			     strlen(mityomapl138_pn_info[i].part_no))) {
+			da850_max_speed = mityomapl138_pn_info[i].max_freq;
+			break;
+		}
+	}
+
+	ret = da850_register_cpufreq("pll0_sysclk3");
+	if (ret)
+		pr_warning("cpufreq registration failed: %d\n", ret);
+}
+#else
+static void mityomapl138_cpufreq_init(const char *partnum) { }
+#endif
+
 static void read_factory_config(struct memory_accessor *a, void *context)
 {
 	int ret;
+	const char *partnum = NULL;
 	struct davinci_soc_info *soc_info = &davinci_soc_info;
 
 	ret = a->read(a, (char *)&factory_config, 0, sizeof(factory_config));
 	if (ret != sizeof(struct factory_config)) {
 		pr_warning("MityOMAPL138: Read Factory Config Failed: %d\n",
 				ret);
-		return;
+		goto bad_config;
 	}
 
 	if (factory_config.magic != FACTORY_CONFIG_MAGIC) {
 		pr_warning("MityOMAPL138: Factory Config Magic Wrong (%X)\n",
 				factory_config.magic);
-		return;
+		goto bad_config;
 	}
 
 	if (factory_config.version != FACTORY_CONFIG_VERSION) {
 		pr_warning("MityOMAPL138: Factory Config Version Wrong (%X)\n",
 				factory_config.version);
-		return;
+		goto bad_config;
 	}
 
 	pr_info("MityOMAPL138: Found MAC = %pM\n", factory_config.mac);
-	pr_info("MityOMAPL138: Part Number = %s\n", factory_config.partnum);
 	if (is_valid_ether_addr(factory_config.mac))
 		memcpy(soc_info->emac_pdata->mac_addr,
 			factory_config.mac, ETH_ALEN);
 	else
 		pr_warning("MityOMAPL138: Invalid MAC found "
 				"in factory config block\n");
+
+	partnum = factory_config.partnum;
+	pr_info("MityOMAPL138: Part Number = %s\n", partnum);
+
+bad_config:
+	/* default maximum speed is valid for all platforms */
+	mityomapl138_cpufreq_init(partnum);
 }
 
 static struct at24_platform_data mityomapl138_fd_chip = {
@@ -223,6 +297,82 @@
 }
 
 /*
+ * SPI Devices:
+ *	SPI1_CS0: 8M Flash ST-M25P64-VME6G
+ */
+static struct mtd_partition spi_flash_partitions[] = {
+	[0] = {
+		.name		= "ubl",
+		.offset		= 0,
+		.size		= SZ_64K,
+		.mask_flags	= MTD_WRITEABLE,
+	},
+	[1] = {
+		.name		= "u-boot",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= SZ_512K,
+		.mask_flags	= MTD_WRITEABLE,
+	},
+	[2] = {
+		.name		= "u-boot-env",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= SZ_64K,
+		.mask_flags	= MTD_WRITEABLE,
+	},
+	[3] = {
+		.name		= "periph-config",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= SZ_64K,
+		.mask_flags	= MTD_WRITEABLE,
+	},
+	[4] = {
+		.name		= "reserved",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= SZ_256K + SZ_64K,
+	},
+	[5] = {
+		.name		= "kernel",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= SZ_2M + SZ_1M,
+	},
+	[6] = {
+		.name		= "fpga",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= SZ_2M,
+	},
+	[7] = {
+		.name		= "spare",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct flash_platform_data mityomapl138_spi_flash_data = {
+	.name		= "m25p80",
+	.parts		= spi_flash_partitions,
+	.nr_parts	= ARRAY_SIZE(spi_flash_partitions),
+	.type		= "m24p64",
+};
+
+static struct davinci_spi_config spi_eprom_config = {
+	.io_type	= SPI_IO_TYPE_DMA,
+	.c2tdelay	= 8,
+	.t2cdelay	= 8,
+};
+
+static struct spi_board_info mityomapl138_spi_flash_info[] = {
+	{
+		.modalias		= "m25p80",
+		.platform_data		= &mityomapl138_spi_flash_data,
+		.controller_data	= &spi_eprom_config,
+		.mode			= SPI_MODE_0,
+		.max_speed_hz		= 30000000,
+		.bus_num		= 1,
+		.chip_select		= 0,
+	},
+};
+
+/*
  * MityDSP-L138 includes a 256 MByte large-page NAND flash
  * (128K blocks).
  */
@@ -377,16 +527,17 @@
 
 	mityomapl138_setup_nand();
 
+	ret = da8xx_register_spi(1, mityomapl138_spi_flash_info,
+			       ARRAY_SIZE(mityomapl138_spi_flash_info));
+	if (ret)
+		pr_warning("spi 1 registration failed: %d\n", ret);
+
 	mityomapl138_config_emac();
 
 	ret = da8xx_register_rtc();
 	if (ret)
 		pr_warning("rtc setup failed: %d\n", ret);
 
-	ret = da850_register_cpufreq("pll0_sysclk3");
-	if (ret)
-		pr_warning("cpufreq registration failed: %d\n", ret);
-
 	ret = da8xx_register_cpuidle();
 	if (ret)
 		pr_warning("cpuidle registration failed: %d\n", ret);
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c
index 0b8dbdb..67c38d0 100644
--- a/arch/arm/mach-davinci/board-omapl138-hawk.c
+++ b/arch/arm/mach-davinci/board-omapl138-hawk.c
@@ -19,6 +19,279 @@
 
 #include <mach/cp_intc.h>
 #include <mach/da8xx.h>
+#include <mach/mux.h>
+
+#define HAWKBOARD_PHY_ID		"0:07"
+#define DA850_HAWK_MMCSD_CD_PIN		GPIO_TO_PIN(3, 12)
+#define DA850_HAWK_MMCSD_WP_PIN		GPIO_TO_PIN(3, 13)
+
+#define DA850_USB1_VBUS_PIN		GPIO_TO_PIN(2, 4)
+#define DA850_USB1_OC_PIN		GPIO_TO_PIN(6, 13)
+
+static short omapl138_hawk_mii_pins[] __initdata = {
+	DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
+	DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
+	DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
+	DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
+	DA850_MDIO_D,
+	-1
+};
+
+static __init void omapl138_hawk_config_emac(void)
+{
+	void __iomem *cfgchip3 = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
+	int ret;
+	u32 val;
+	struct davinci_soc_info *soc_info = &davinci_soc_info;
+
+	val = __raw_readl(cfgchip3);
+	val &= ~BIT(8);
+	ret = davinci_cfg_reg_list(omapl138_hawk_mii_pins);
+	if (ret) {
+		pr_warning("%s: cpgmac/mii mux setup failed: %d\n",
+			__func__, ret);
+		return;
+	}
+
+	/* configure the CFGCHIP3 register for MII */
+	__raw_writel(val, cfgchip3);
+	pr_info("EMAC: MII PHY configured\n");
+
+	soc_info->emac_pdata->phy_id = HAWKBOARD_PHY_ID;
+
+	ret = da8xx_register_emac();
+	if (ret)
+		pr_warning("%s: emac registration failed: %d\n",
+			__func__, ret);
+}
+
+/*
+ * The following EDMA channels/slots are not being used by drivers (for
+ * example: Timer, GPIO, UART events etc) on da850/omap-l138 EVM/Hawkboard,
+ * hence they are being reserved for codecs on the DSP side.
+ */
+static const s16 da850_dma0_rsv_chans[][2] = {
+	/* (offset, number) */
+	{ 8,  6},
+	{24,  4},
+	{30,  2},
+	{-1, -1}
+};
+
+static const s16 da850_dma0_rsv_slots[][2] = {
+	/* (offset, number) */
+	{ 8,  6},
+	{24,  4},
+	{30, 50},
+	{-1, -1}
+};
+
+static const s16 da850_dma1_rsv_chans[][2] = {
+	/* (offset, number) */
+	{ 0, 28},
+	{30,  2},
+	{-1, -1}
+};
+
+static const s16 da850_dma1_rsv_slots[][2] = {
+	/* (offset, number) */
+	{ 0, 28},
+	{30, 90},
+	{-1, -1}
+};
+
+static struct edma_rsv_info da850_edma_cc0_rsv = {
+	.rsv_chans	= da850_dma0_rsv_chans,
+	.rsv_slots	= da850_dma0_rsv_slots,
+};
+
+static struct edma_rsv_info da850_edma_cc1_rsv = {
+	.rsv_chans	= da850_dma1_rsv_chans,
+	.rsv_slots	= da850_dma1_rsv_slots,
+};
+
+static struct edma_rsv_info *da850_edma_rsv[2] = {
+	&da850_edma_cc0_rsv,
+	&da850_edma_cc1_rsv,
+};
+
+static const short hawk_mmcsd0_pins[] = {
+	DA850_MMCSD0_DAT_0, DA850_MMCSD0_DAT_1, DA850_MMCSD0_DAT_2,
+	DA850_MMCSD0_DAT_3, DA850_MMCSD0_CLK, DA850_MMCSD0_CMD,
+	DA850_GPIO3_12, DA850_GPIO3_13,
+	-1
+};
+
+static int da850_hawk_mmc_get_ro(int index)
+{
+	return gpio_get_value(DA850_HAWK_MMCSD_WP_PIN);
+}
+
+static int da850_hawk_mmc_get_cd(int index)
+{
+	return !gpio_get_value(DA850_HAWK_MMCSD_CD_PIN);
+}
+
+static struct davinci_mmc_config da850_mmc_config = {
+	.get_ro		= da850_hawk_mmc_get_ro,
+	.get_cd		= da850_hawk_mmc_get_cd,
+	.wires		= 4,
+	.max_freq	= 50000000,
+	.caps		= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
+	.version	= MMC_CTLR_VERSION_2,
+};
+
+static __init void omapl138_hawk_mmc_init(void)
+{
+	int ret;
+
+	ret = davinci_cfg_reg_list(hawk_mmcsd0_pins);
+	if (ret) {
+		pr_warning("%s: MMC/SD0 mux setup failed: %d\n",
+			__func__, ret);
+		return;
+	}
+
+	ret = gpio_request_one(DA850_HAWK_MMCSD_CD_PIN,
+			GPIOF_DIR_IN, "MMC CD");
+	if (ret < 0) {
+		pr_warning("%s: can not open GPIO %d\n",
+			__func__, DA850_HAWK_MMCSD_CD_PIN);
+		return;
+	}
+
+	ret = gpio_request_one(DA850_HAWK_MMCSD_WP_PIN,
+			GPIOF_DIR_IN, "MMC WP");
+	if (ret < 0) {
+		pr_warning("%s: can not open GPIO %d\n",
+			__func__, DA850_HAWK_MMCSD_WP_PIN);
+		goto mmc_setup_wp_fail;
+	}
+
+	ret = da8xx_register_mmcsd0(&da850_mmc_config);
+	if (ret) {
+		pr_warning("%s: MMC/SD0 registration failed: %d\n",
+			__func__, ret);
+		goto mmc_setup_mmcsd_fail;
+	}
+
+	return;
+
+mmc_setup_mmcsd_fail:
+	gpio_free(DA850_HAWK_MMCSD_WP_PIN);
+mmc_setup_wp_fail:
+	gpio_free(DA850_HAWK_MMCSD_CD_PIN);
+}
+
+static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id);
+static da8xx_ocic_handler_t hawk_usb_ocic_handler;
+
+static const short da850_hawk_usb11_pins[] = {
+	DA850_GPIO2_4, DA850_GPIO6_13,
+	-1
+};
+
+static int hawk_usb_set_power(unsigned port, int on)
+{
+	gpio_set_value(DA850_USB1_VBUS_PIN, on);
+	return 0;
+}
+
+static int hawk_usb_get_power(unsigned port)
+{
+	return gpio_get_value(DA850_USB1_VBUS_PIN);
+}
+
+static int hawk_usb_get_oci(unsigned port)
+{
+	return !gpio_get_value(DA850_USB1_OC_PIN);
+}
+
+static int hawk_usb_ocic_notify(da8xx_ocic_handler_t handler)
+{
+	int irq         = gpio_to_irq(DA850_USB1_OC_PIN);
+	int error       = 0;
+
+	if (handler != NULL) {
+		hawk_usb_ocic_handler = handler;
+
+		error = request_irq(irq, omapl138_hawk_usb_ocic_irq,
+					IRQF_DISABLED | IRQF_TRIGGER_RISING |
+					IRQF_TRIGGER_FALLING,
+					"OHCI over-current indicator", NULL);
+		if (error)
+			pr_err("%s: could not request IRQ to watch "
+				"over-current indicator changes\n", __func__);
+	} else {
+		free_irq(irq, NULL);
+	}
+	return error;
+}
+
+static struct da8xx_ohci_root_hub omapl138_hawk_usb11_pdata = {
+	.set_power      = hawk_usb_set_power,
+	.get_power      = hawk_usb_get_power,
+	.get_oci        = hawk_usb_get_oci,
+	.ocic_notify    = hawk_usb_ocic_notify,
+	/* TPS2087 switch @ 5V */
+	.potpgt         = (3 + 1) / 2,  /* 3 ms max */
+};
+
+static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id)
+{
+	hawk_usb_ocic_handler(&omapl138_hawk_usb11_pdata, 1);
+	return IRQ_HANDLED;
+}
+
+static __init void omapl138_hawk_usb_init(void)
+{
+	int ret;
+	u32 cfgchip2;
+
+	ret = davinci_cfg_reg_list(da850_hawk_usb11_pins);
+	if (ret) {
+		pr_warning("%s: USB 1.1 PinMux setup failed: %d\n",
+			__func__, ret);
+		return;
+	}
+
+	/* Setup the Ref. clock frequency for the HAWK at 24 MHz. */
+
+	cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+	cfgchip2 &= ~CFGCHIP2_REFFREQ;
+	cfgchip2 |=  CFGCHIP2_REFFREQ_24MHZ;
+	__raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	ret = gpio_request_one(DA850_USB1_VBUS_PIN,
+			GPIOF_DIR_OUT, "USB1 VBUS");
+	if (ret < 0) {
+		pr_err("%s: failed to request GPIO for USB 1.1 port "
+			"power control: %d\n", __func__, ret);
+		return;
+	}
+
+	ret = gpio_request_one(DA850_USB1_OC_PIN,
+			GPIOF_DIR_IN, "USB1 OC");
+	if (ret < 0) {
+		pr_err("%s: failed to request GPIO for USB 1.1 port "
+			"over-current indicator: %d\n", __func__, ret);
+		goto usb11_setup_oc_fail;
+	}
+
+	ret = da8xx_register_usb11(&omapl138_hawk_usb11_pdata);
+	if (ret) {
+		pr_warning("%s: USB 1.1 registration failed: %d\n",
+			__func__, ret);
+		goto usb11_setup_fail;
+	}
+
+	return;
+
+usb11_setup_fail:
+	gpio_free(DA850_USB1_OC_PIN);
+usb11_setup_oc_fail:
+	gpio_free(DA850_USB1_VBUS_PIN);
+}
 
 static struct davinci_uart_config omapl138_hawk_uart_config __initdata = {
 	.enabled_uarts = 0x7,
@@ -30,6 +303,17 @@
 
 	davinci_serial_init(&omapl138_hawk_uart_config);
 
+	omapl138_hawk_config_emac();
+
+	ret = da850_register_edma(da850_edma_rsv);
+	if (ret)
+		pr_warning("%s: EDMA registration failed: %d\n",
+			__func__, ret);
+
+	omapl138_hawk_mmc_init();
+
+	omapl138_hawk_usb_init();
+
 	ret = da8xx_register_watchdog();
 	if (ret)
 		pr_warning("omapl138_hawk_init: "
diff --git a/arch/arm/mach-davinci/da830.c b/arch/arm/mach-davinci/da830.c
index ec23ab4..2ed2f82 100644
--- a/arch/arm/mach-davinci/da830.c
+++ b/arch/arm/mach-davinci/da830.c
@@ -148,7 +148,7 @@
 static struct clk dmax_clk = {
 	.name		= "dmax",
 	.parent		= &pll0_sysclk2,
-	.lpsc		= DA8XX_LPSC0_DMAX,
+	.lpsc		= DA8XX_LPSC0_PRUSS,
 	.flags		= ALWAYS_ENABLED,
 };
 
@@ -397,8 +397,8 @@
 	CLK(NULL,		"uart0",	&uart0_clk),
 	CLK(NULL,		"uart1",	&uart1_clk),
 	CLK(NULL,		"uart2",	&uart2_clk),
-	CLK("dm_spi.0",		NULL,		&spi0_clk),
-	CLK("dm_spi.1",		NULL,		&spi1_clk),
+	CLK("spi_davinci.0",	NULL,		&spi0_clk),
+	CLK("spi_davinci.1",	NULL,		&spi1_clk),
 	CLK(NULL,		"ecap0",	&ecap0_clk),
 	CLK(NULL,		"ecap1",	&ecap1_clk),
 	CLK(NULL,		"ecap2",	&ecap2_clk),
diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c
index 78b5ae2..68fe4c2 100644
--- a/arch/arm/mach-davinci/da850.c
+++ b/arch/arm/mach-davinci/da850.c
@@ -345,6 +345,34 @@
 	.flags		= ALWAYS_ENABLED,
 };
 
+static struct clk usb11_clk = {
+	.name		= "usb11",
+	.parent		= &pll0_sysclk4,
+	.lpsc		= DA8XX_LPSC1_USB11,
+	.gpsc		= 1,
+};
+
+static struct clk usb20_clk = {
+	.name		= "usb20",
+	.parent		= &pll0_sysclk2,
+	.lpsc		= DA8XX_LPSC1_USB20,
+	.gpsc		= 1,
+};
+
+static struct clk spi0_clk = {
+	.name		= "spi0",
+	.parent		= &pll0_sysclk2,
+	.lpsc		= DA8XX_LPSC0_SPI0,
+};
+
+static struct clk spi1_clk = {
+	.name		= "spi1",
+	.parent		= &pll0_sysclk2,
+	.lpsc		= DA8XX_LPSC1_SPI1,
+	.gpsc		= 1,
+	.flags		= DA850_CLK_ASYNC3,
+};
+
 static struct clk_lookup da850_clks[] = {
 	CLK(NULL,		"ref",		&ref_clk),
 	CLK(NULL,		"pll0",		&pll0_clk),
@@ -387,6 +415,10 @@
 	CLK("davinci_mmc.0",	NULL,		&mmcsd0_clk),
 	CLK("davinci_mmc.1",	NULL,		&mmcsd1_clk),
 	CLK(NULL,		"aemif",	&aemif_clk),
+	CLK(NULL,		"usb11",	&usb11_clk),
+	CLK(NULL,		"usb20",	&usb20_clk),
+	CLK("spi_davinci.0",	NULL,		&spi0_clk),
+	CLK("spi_davinci.1",	NULL,		&spi1_clk),
 	CLK(NULL,		NULL,		NULL),
 };
 
@@ -543,30 +575,19 @@
 	MUX_CFG(DA850, EMA_WAIT_1,	6,	24,	15,	1,	false)
 	MUX_CFG(DA850, NEMA_CS_2,	7,	0,	15,	1,	false)
 	/* GPIO function */
+	MUX_CFG(DA850, GPIO2_4,		6,	12,	15,	8,	false)
 	MUX_CFG(DA850, GPIO2_6,		6,	4,	15,	8,	false)
 	MUX_CFG(DA850, GPIO2_8,		5,	28,	15,	8,	false)
 	MUX_CFG(DA850, GPIO2_15,	5,	0,	15,	8,	false)
+	MUX_CFG(DA850, GPIO3_12,	7,	12,	15,	8,	false)
+	MUX_CFG(DA850, GPIO3_13,	7,	8,	15,	8,	false)
 	MUX_CFG(DA850, GPIO4_0,		10,	28,	15,	8,	false)
 	MUX_CFG(DA850, GPIO4_1,		10,	24,	15,	8,	false)
+	MUX_CFG(DA850, GPIO6_13,	13,	8,	15,	8,	false)
 	MUX_CFG(DA850, RTC_ALARM,	0,	28,	15,	2,	false)
 #endif
 };
 
-const short da850_uart0_pins[] __initdata = {
-	DA850_NUART0_CTS, DA850_NUART0_RTS, DA850_UART0_RXD, DA850_UART0_TXD,
-	-1
-};
-
-const short da850_uart1_pins[] __initdata = {
-	DA850_UART1_RXD, DA850_UART1_TXD,
-	-1
-};
-
-const short da850_uart2_pins[] __initdata = {
-	DA850_UART2_RXD, DA850_UART2_TXD,
-	-1
-};
-
 const short da850_i2c0_pins[] __initdata = {
 	DA850_I2C0_SDA, DA850_I2C0_SCL,
 	-1
@@ -577,24 +598,6 @@
 	-1
 };
 
-const short da850_cpgmac_pins[] __initdata = {
-	DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
-	DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
-	DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
-	DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
-	DA850_MDIO_D, DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
-	DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1, DA850_RMII_RXER,
-	DA850_RMII_MHZ_50_CLK,
-	-1
-};
-
-const short da850_mcasp_pins[] __initdata = {
-	DA850_AHCLKX, DA850_ACLKX, DA850_AFSX,
-	DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE,
-	DA850_AXR_11, DA850_AXR_12,
-	-1
-};
-
 const short da850_lcdcntl_pins[] __initdata = {
 	DA850_LCD_D_0, DA850_LCD_D_1, DA850_LCD_D_2, DA850_LCD_D_3,
 	DA850_LCD_D_4, DA850_LCD_D_5, DA850_LCD_D_6, DA850_LCD_D_7,
@@ -604,29 +607,6 @@
 	-1
 };
 
-const short da850_mmcsd0_pins[] __initdata = {
-	DA850_MMCSD0_DAT_0, DA850_MMCSD0_DAT_1, DA850_MMCSD0_DAT_2,
-	DA850_MMCSD0_DAT_3, DA850_MMCSD0_CLK, DA850_MMCSD0_CMD,
-	DA850_GPIO4_0, DA850_GPIO4_1,
-	-1
-};
-
-const short da850_emif25_pins[] __initdata = {
-	DA850_EMA_BA_1, DA850_EMA_CLK, DA850_EMA_WAIT_1, DA850_NEMA_CS_2,
-	DA850_NEMA_CS_3, DA850_NEMA_CS_4, DA850_NEMA_WE, DA850_NEMA_OE,
-	DA850_EMA_D_0, DA850_EMA_D_1, DA850_EMA_D_2, DA850_EMA_D_3,
-	DA850_EMA_D_4, DA850_EMA_D_5, DA850_EMA_D_6, DA850_EMA_D_7,
-	DA850_EMA_D_8, DA850_EMA_D_9, DA850_EMA_D_10, DA850_EMA_D_11,
-	DA850_EMA_D_12, DA850_EMA_D_13, DA850_EMA_D_14, DA850_EMA_D_15,
-	DA850_EMA_A_0, DA850_EMA_A_1, DA850_EMA_A_2, DA850_EMA_A_3,
-	DA850_EMA_A_4, DA850_EMA_A_5, DA850_EMA_A_6, DA850_EMA_A_7,
-	DA850_EMA_A_8, DA850_EMA_A_9, DA850_EMA_A_10, DA850_EMA_A_11,
-	DA850_EMA_A_12, DA850_EMA_A_13, DA850_EMA_A_14, DA850_EMA_A_15,
-	DA850_EMA_A_16, DA850_EMA_A_17, DA850_EMA_A_18, DA850_EMA_A_19,
-	DA850_EMA_A_20, DA850_EMA_A_21, DA850_EMA_A_22, DA850_EMA_A_23,
-	-1
-};
-
 /* FIQ are pri 0-1; otherwise 2-7, with 7 lowest priority */
 static u8 da850_default_priorities[DA850_N_CP_INTC_IRQ] = {
 	[IRQ_DA8XX_COMMTX]		= 7,
@@ -764,6 +744,13 @@
 		.cpu_id		= DAVINCI_CPU_ID_DA850,
 		.name		= "da850/omap-l138",
 	},
+	{
+		.variant	= 0x1,
+		.part_no	= 0xb7d1,
+		.manufacturer	= 0x017,	/* 0x02f >> 1 */
+		.cpu_id		= DAVINCI_CPU_ID_DA850,
+		.name		= "da850/omap-l138/am18x",
+	},
 };
 
 static struct davinci_timer_instance da850_timer_instance[4] = {
diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c
index beda8a4..625d4b6 100644
--- a/arch/arm/mach-davinci/devices-da8xx.c
+++ b/arch/arm/mach-davinci/devices-da8xx.c
@@ -38,12 +38,23 @@
 #define DA8XX_EMAC_MDIO_BASE		0x01e24000
 #define DA8XX_GPIO_BASE			0x01e26000
 #define DA8XX_I2C1_BASE			0x01e28000
+#define DA8XX_SPI0_BASE			0x01c41000
+#define DA8XX_SPI1_BASE			0x01f0e000
 
 #define DA8XX_EMAC_CTRL_REG_OFFSET	0x3000
 #define DA8XX_EMAC_MOD_REG_OFFSET	0x2000
 #define DA8XX_EMAC_RAM_OFFSET		0x0000
 #define DA8XX_EMAC_CTRL_RAM_SIZE	SZ_8K
 
+#define DA8XX_DMA_SPI0_RX	EDMA_CTLR_CHAN(0, 14)
+#define DA8XX_DMA_SPI0_TX	EDMA_CTLR_CHAN(0, 15)
+#define DA8XX_DMA_MMCSD0_RX	EDMA_CTLR_CHAN(0, 16)
+#define DA8XX_DMA_MMCSD0_TX	EDMA_CTLR_CHAN(0, 17)
+#define DA8XX_DMA_SPI1_RX	EDMA_CTLR_CHAN(0, 18)
+#define DA8XX_DMA_SPI1_TX	EDMA_CTLR_CHAN(0, 19)
+#define DA850_DMA_MMCSD1_RX	EDMA_CTLR_CHAN(1, 28)
+#define DA850_DMA_MMCSD1_TX	EDMA_CTLR_CHAN(1, 29)
+
 void __iomem *da8xx_syscfg0_base;
 void __iomem *da8xx_syscfg1_base;
 
@@ -573,13 +584,13 @@
 		.flags	= IORESOURCE_IRQ,
 	},
 	{		/* DMA RX */
-		.start	= EDMA_CTLR_CHAN(0, 16),
-		.end	= EDMA_CTLR_CHAN(0, 16),
+		.start	= DA8XX_DMA_MMCSD0_RX,
+		.end	= DA8XX_DMA_MMCSD0_RX,
 		.flags	= IORESOURCE_DMA,
 	},
 	{		/* DMA TX */
-		.start	= EDMA_CTLR_CHAN(0, 17),
-		.end	= EDMA_CTLR_CHAN(0, 17),
+		.start	= DA8XX_DMA_MMCSD0_TX,
+		.end	= DA8XX_DMA_MMCSD0_TX,
 		.flags	= IORESOURCE_DMA,
 	},
 };
@@ -610,13 +621,13 @@
 		.flags	= IORESOURCE_IRQ,
 	},
 	{		/* DMA RX */
-		.start	= EDMA_CTLR_CHAN(1, 28),
-		.end	= EDMA_CTLR_CHAN(1, 28),
+		.start	= DA850_DMA_MMCSD1_RX,
+		.end	= DA850_DMA_MMCSD1_RX,
 		.flags	= IORESOURCE_DMA,
 	},
 	{		/* DMA TX */
-		.start	= EDMA_CTLR_CHAN(1, 29),
-		.end	= EDMA_CTLR_CHAN(1, 29),
+		.start	= DA850_DMA_MMCSD1_TX,
+		.end	= DA850_DMA_MMCSD1_TX,
 		.flags	= IORESOURCE_DMA,
 	},
 };
@@ -725,3 +736,101 @@
 
 	return platform_device_register(&da8xx_cpuidle_device);
 }
+
+static struct resource da8xx_spi0_resources[] = {
+	[0] = {
+		.start	= DA8XX_SPI0_BASE,
+		.end	= DA8XX_SPI0_BASE + SZ_4K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= IRQ_DA8XX_SPINT0,
+		.end	= IRQ_DA8XX_SPINT0,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= DA8XX_DMA_SPI0_RX,
+		.end	= DA8XX_DMA_SPI0_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= DA8XX_DMA_SPI0_TX,
+		.end	= DA8XX_DMA_SPI0_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct resource da8xx_spi1_resources[] = {
+	[0] = {
+		.start	= DA8XX_SPI1_BASE,
+		.end	= DA8XX_SPI1_BASE + SZ_4K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= IRQ_DA8XX_SPINT1,
+		.end	= IRQ_DA8XX_SPINT1,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= DA8XX_DMA_SPI1_RX,
+		.end	= DA8XX_DMA_SPI1_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= DA8XX_DMA_SPI1_TX,
+		.end	= DA8XX_DMA_SPI1_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+struct davinci_spi_platform_data da8xx_spi_pdata[] = {
+	[0] = {
+		.version	= SPI_VERSION_2,
+		.intr_line	= 1,
+		.dma_event_q	= EVENTQ_0,
+	},
+	[1] = {
+		.version	= SPI_VERSION_2,
+		.intr_line	= 1,
+		.dma_event_q	= EVENTQ_0,
+	},
+};
+
+static struct platform_device da8xx_spi_device[] = {
+	[0] = {
+		.name		= "spi_davinci",
+		.id		= 0,
+		.num_resources	= ARRAY_SIZE(da8xx_spi0_resources),
+		.resource	= da8xx_spi0_resources,
+		.dev		= {
+			.platform_data = &da8xx_spi_pdata[0],
+		},
+	},
+	[1] = {
+		.name		= "spi_davinci",
+		.id		= 1,
+		.num_resources	= ARRAY_SIZE(da8xx_spi1_resources),
+		.resource	= da8xx_spi1_resources,
+		.dev		= {
+			.platform_data = &da8xx_spi_pdata[1],
+		},
+	},
+};
+
+int __init da8xx_register_spi(int instance, struct spi_board_info *info,
+			      unsigned len)
+{
+	int ret;
+
+	if (instance < 0 || instance > 1)
+		return -EINVAL;
+
+	ret = spi_register_board_info(info, len);
+	if (ret)
+		pr_warning("%s: failed to register board info for spi %d :"
+			   " %d\n", __func__, instance, ret);
+
+	da8xx_spi_pdata[instance].num_chipselect = len;
+
+	return platform_device_register(&da8xx_spi_device[instance]);
+}
diff --git a/arch/arm/mach-davinci/dm355.c b/arch/arm/mach-davinci/dm355.c
index a5f8a80..76364d134 100644
--- a/arch/arm/mach-davinci/dm355.c
+++ b/arch/arm/mach-davinci/dm355.c
@@ -403,16 +403,13 @@
 		.start = 16,
 		.flags = IORESOURCE_DMA,
 	},
-	{
-		.start = EVENTQ_1,
-		.flags = IORESOURCE_DMA,
-	},
 };
 
 static struct davinci_spi_platform_data dm355_spi0_pdata = {
 	.version 	= SPI_VERSION_1,
 	.num_chipselect = 2,
 	.cshold_bug	= true,
+	.dma_event_q	= EVENTQ_1,
 };
 static struct platform_device dm355_spi0_device = {
 	.name = "spi_davinci",
diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c
index 02d2cc3..4604e72 100644
--- a/arch/arm/mach-davinci/dm365.c
+++ b/arch/arm/mach-davinci/dm365.c
@@ -625,6 +625,7 @@
 static struct davinci_spi_platform_data dm365_spi0_pdata = {
 	.version 	= SPI_VERSION_1,
 	.num_chipselect = 2,
+	.dma_event_q	= EVENTQ_3,
 };
 
 static struct resource dm365_spi0_resources[] = {
@@ -645,10 +646,6 @@
 		.start = 16,
 		.flags = IORESOURCE_DMA,
 	},
-	{
-		.start = EVENTQ_3,
-		.flags = IORESOURCE_DMA,
-	},
 };
 
 static struct platform_device dm365_spi0_device = {
diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h
index e7f9520..e4fc1af 100644
--- a/arch/arm/mach-davinci/include/mach/da8xx.h
+++ b/arch/arm/mach-davinci/include/mach/da8xx.h
@@ -15,6 +15,7 @@
 
 #include <linux/platform_device.h>
 #include <linux/davinci_emac.h>
+#include <linux/spi/spi.h>
 
 #include <mach/serial.h>
 #include <mach/edma.h>
@@ -23,6 +24,7 @@
 #include <mach/mmc.h>
 #include <mach/usb.h>
 #include <mach/pm.h>
+#include <mach/spi.h>
 
 extern void __iomem *da8xx_syscfg0_base;
 extern void __iomem *da8xx_syscfg1_base;
@@ -77,6 +79,7 @@
 int da830_register_edma(struct edma_rsv_info *rsv);
 int da850_register_edma(struct edma_rsv_info *rsv[2]);
 int da8xx_register_i2c(int instance, struct davinci_i2c_platform_data *pdata);
+int da8xx_register_spi(int instance, struct spi_board_info *info, unsigned len);
 int da8xx_register_watchdog(void);
 int da8xx_register_usb20(unsigned mA, unsigned potpgt);
 int da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata);
@@ -95,6 +98,7 @@
 extern struct emac_platform_data da8xx_emac_pdata;
 extern struct da8xx_lcdc_platform_data sharp_lcd035q3dg01_pdata;
 extern struct da8xx_lcdc_platform_data sharp_lk043t1dg01_pdata;
+extern struct davinci_spi_platform_data da8xx_spi_pdata[];
 
 extern struct platform_device da8xx_wdt_device;
 
@@ -123,15 +127,8 @@
 extern const short da830_eqep0_pins[];
 extern const short da830_eqep1_pins[];
 
-extern const short da850_uart0_pins[];
-extern const short da850_uart1_pins[];
-extern const short da850_uart2_pins[];
 extern const short da850_i2c0_pins[];
 extern const short da850_i2c1_pins[];
-extern const short da850_cpgmac_pins[];
-extern const short da850_mcasp_pins[];
 extern const short da850_lcdcntl_pins[];
-extern const short da850_mmcsd0_pins[];
-extern const short da850_emif25_pins[];
 
 #endif /* __ASM_ARCH_DAVINCI_DA8XX_H */
diff --git a/arch/arm/mach-davinci/include/mach/edma.h b/arch/arm/mach-davinci/include/mach/edma.h
index dc10ef6..20c77f2 100644
--- a/arch/arm/mach-davinci/include/mach/edma.h
+++ b/arch/arm/mach-davinci/include/mach/edma.h
@@ -151,42 +151,6 @@
 #define DA830_DMACH2EVENT_MAP1		0x00000000u
 #define DA830_EDMA_ARM_OWN		0x30FFCCFFu
 
-/* DA830 specific EDMA3 Events Information */
-enum DA830_edma_ch {
-	DA830_DMACH_MCASP0_RX,
-	DA830_DMACH_MCASP0_TX,
-	DA830_DMACH_MCASP1_RX,
-	DA830_DMACH_MCASP1_TX,
-	DA830_DMACH_MCASP2_RX,
-	DA830_DMACH_MCASP2_TX,
-	DA830_DMACH_GPIO_BNK0INT,
-	DA830_DMACH_GPIO_BNK1INT,
-	DA830_DMACH_UART0_RX,
-	DA830_DMACH_UART0_TX,
-	DA830_DMACH_TMR64P0_EVTOUT12,
-	DA830_DMACH_TMR64P0_EVTOUT34,
-	DA830_DMACH_UART1_RX,
-	DA830_DMACH_UART1_TX,
-	DA830_DMACH_SPI0_RX,
-	DA830_DMACH_SPI0_TX,
-	DA830_DMACH_MMCSD_RX,
-	DA830_DMACH_MMCSD_TX,
-	DA830_DMACH_SPI1_RX,
-	DA830_DMACH_SPI1_TX,
-	DA830_DMACH_DMAX_EVTOUT6,
-	DA830_DMACH_DMAX_EVTOUT7,
-	DA830_DMACH_GPIO_BNK2INT,
-	DA830_DMACH_GPIO_BNK3INT,
-	DA830_DMACH_I2C0_RX,
-	DA830_DMACH_I2C0_TX,
-	DA830_DMACH_I2C1_RX,
-	DA830_DMACH_I2C1_TX,
-	DA830_DMACH_GPIO_BNK4INT,
-	DA830_DMACH_GPIO_BNK5INT,
-	DA830_DMACH_UART2_RX,
-	DA830_DMACH_UART2_TX
-};
-
 /*ch_status paramater of callback function possible values*/
 #define DMA_COMPLETE 1
 #define DMA_CC_ERROR 2
diff --git a/arch/arm/mach-davinci/include/mach/mux.h b/arch/arm/mach-davinci/include/mach/mux.h
index de11aac..5d4e0fe 100644
--- a/arch/arm/mach-davinci/include/mach/mux.h
+++ b/arch/arm/mach-davinci/include/mach/mux.h
@@ -908,11 +908,15 @@
 	DA850_NEMA_CS_2,
 
 	/* GPIO function */
+	DA850_GPIO2_4,
 	DA850_GPIO2_6,
 	DA850_GPIO2_8,
 	DA850_GPIO2_15,
+	DA850_GPIO3_12,
+	DA850_GPIO3_13,
 	DA850_GPIO4_0,
 	DA850_GPIO4_1,
+	DA850_GPIO6_13,
 	DA850_RTC_ALARM,
 };
 
diff --git a/arch/arm/mach-davinci/include/mach/psc.h b/arch/arm/mach-davinci/include/mach/psc.h
index 62b0858..a47e6f2 100644
--- a/arch/arm/mach-davinci/include/mach/psc.h
+++ b/arch/arm/mach-davinci/include/mach/psc.h
@@ -150,7 +150,7 @@
 #define DA8XX_LPSC0_SCR0_SS		10
 #define DA8XX_LPSC0_SCR1_SS		11
 #define DA8XX_LPSC0_SCR2_SS		12
-#define DA8XX_LPSC0_DMAX		13
+#define DA8XX_LPSC0_PRUSS		13
 #define DA8XX_LPSC0_ARM			14
 #define DA8XX_LPSC0_GEM			15
 
diff --git a/arch/arm/mach-davinci/include/mach/spi.h b/arch/arm/mach-davinci/include/mach/spi.h
index 38f4da5..7af305b 100644
--- a/arch/arm/mach-davinci/include/mach/spi.h
+++ b/arch/arm/mach-davinci/include/mach/spi.h
@@ -19,6 +19,8 @@
 #ifndef __ARCH_ARM_DAVINCI_SPI_H
 #define __ARCH_ARM_DAVINCI_SPI_H
 
+#include <mach/edma.h>
+
 #define SPI_INTERN_CS	0xFF
 
 enum {
@@ -39,13 +41,16 @@
  *		to populate if all chip-selects are internal.
  * @cshold_bug:	set this to true if the SPI controller on your chip requires
  *		a write to CSHOLD bit in between transfers (like in DM355).
+ * @dma_event_q: DMA event queue to use if SPI_IO_TYPE_DMA is used for any
+ *		device on the bus.
  */
 struct davinci_spi_platform_data {
-	u8	version;
-	u8	num_chipselect;
-	u8	intr_line;
-	u8	*chip_sel;
-	bool	cshold_bug;
+	u8			version;
+	u8			num_chipselect;
+	u8			intr_line;
+	u8			*chip_sel;
+	bool			cshold_bug;
+	enum dma_event_q	dma_event_q;
 };
 
 /**
diff --git a/drivers/spi/davinci_spi.c b/drivers/spi/davinci_spi.c
index 6beab99..166a879 100644
--- a/drivers/spi/davinci_spi.c
+++ b/drivers/spi/davinci_spi.c
@@ -790,7 +790,6 @@
 	struct resource *r, *mem;
 	resource_size_t dma_rx_chan = SPI_NO_RESOURCE;
 	resource_size_t	dma_tx_chan = SPI_NO_RESOURCE;
-	resource_size_t	dma_eventq = SPI_NO_RESOURCE;
 	int i = 0, ret = 0;
 	u32 spipc0;
 
@@ -878,17 +877,13 @@
 	r = platform_get_resource(pdev, IORESOURCE_DMA, 1);
 	if (r)
 		dma_tx_chan = r->start;
-	r = platform_get_resource(pdev, IORESOURCE_DMA, 2);
-	if (r)
-		dma_eventq = r->start;
 
 	dspi->bitbang.txrx_bufs = davinci_spi_bufs;
 	if (dma_rx_chan != SPI_NO_RESOURCE &&
-	    dma_tx_chan != SPI_NO_RESOURCE &&
-	    dma_eventq != SPI_NO_RESOURCE) {
+	    dma_tx_chan != SPI_NO_RESOURCE) {
 		dspi->dma.rx_channel = dma_rx_chan;
 		dspi->dma.tx_channel = dma_tx_chan;
-		dspi->dma.eventq = dma_eventq;
+		dspi->dma.eventq = pdata->dma_event_q;
 
 		ret = davinci_spi_request_dma(dspi);
 		if (ret)
@@ -897,7 +892,7 @@
 		dev_info(&pdev->dev, "DMA: supported\n");
 		dev_info(&pdev->dev, "DMA: RX channel: %d, TX channel: %d, "
 				"event queue: %d\n", dma_rx_chan, dma_tx_chan,
-				dma_eventq);
+				pdata->dma_event_q);
 	}
 
 	dspi->get_rx = davinci_spi_rx_buf_u8;