ARM: at91: add atmel-mci support for chips and boards which can use it
Since atmel-mci driver supports all atmel mci versions,
use it instead of the deprecated at91_mci driver.
Platform data and all related configuration are removed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
[nicolas.ferre@atmel.com: remove at91_mci platform data]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index 175e000..aa15997 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -218,9 +218,9 @@
* MMC / SD
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
+#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct at91_mmc_data mmc0_data, mmc1_data;
+static struct mci_platform_data mmc0_data, mmc1_data;
static struct resource mmc0_resources[] = {
[0] = {
@@ -236,7 +236,7 @@
};
static struct platform_device at91sam9263_mmc0_device = {
- .name = "at91_mci",
+ .name = "atmel_mci",
.id = 0,
.dev = {
.dma_mask = &mmc_dmamask,
@@ -261,7 +261,7 @@
};
static struct platform_device at91sam9263_mmc1_device = {
- .name = "at91_mci",
+ .name = "atmel_mci",
.id = 1,
.dev = {
.dma_mask = &mmc_dmamask,
@@ -272,85 +272,110 @@
.num_resources = ARRAY_SIZE(mmc1_resources),
};
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
+void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
{
+ unsigned int i;
+ unsigned int slot_count = 0;
+
if (!data)
return;
- /* input/irq */
- if (gpio_is_valid(data->det_pin)) {
- at91_set_gpio_input(data->det_pin, 1);
- at91_set_deglitch(data->det_pin, 1);
- }
- if (gpio_is_valid(data->wp_pin))
- at91_set_gpio_input(data->wp_pin, 1);
- if (gpio_is_valid(data->vcc_pin))
- at91_set_gpio_output(data->vcc_pin, 0);
+ for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
- if (mmc_id == 0) { /* MCI0 */
- /* CLK */
- at91_set_A_periph(AT91_PIN_PA12, 0);
+ if (!data->slot[i].bus_width)
+ continue;
- if (data->slot_b) {
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA16, 1);
+ /* input/irq */
+ if (gpio_is_valid(data->slot[i].detect_pin)) {
+ at91_set_gpio_input(data->slot[i].detect_pin,
+ 1);
+ at91_set_deglitch(data->slot[i].detect_pin,
+ 1);
+ }
+ if (gpio_is_valid(data->slot[i].wp_pin))
+ at91_set_gpio_input(data->slot[i].wp_pin, 1);
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA17, 1);
- if (data->wire4) {
- at91_set_A_periph(AT91_PIN_PA18, 1);
- at91_set_A_periph(AT91_PIN_PA19, 1);
- at91_set_A_periph(AT91_PIN_PA20, 1);
+ if (mmc_id == 0) { /* MCI0 */
+ switch (i) {
+ case 0: /* slot A */
+ /* CMD */
+ at91_set_A_periph(AT91_PIN_PA1, 1);
+ /* DAT0, maybe DAT1..DAT3 */
+ at91_set_A_periph(AT91_PIN_PA0, 1);
+ if (data->slot[i].bus_width == 4) {
+ at91_set_A_periph(AT91_PIN_PA3, 1);
+ at91_set_A_periph(AT91_PIN_PA4, 1);
+ at91_set_A_periph(AT91_PIN_PA5, 1);
+ }
+ slot_count++;
+ break;
+ case 1: /* slot B */
+ /* CMD */
+ at91_set_A_periph(AT91_PIN_PA16, 1);
+ /* DAT0, maybe DAT1..DAT3 */
+ at91_set_A_periph(AT91_PIN_PA17, 1);
+ if (data->slot[i].bus_width == 4) {
+ at91_set_A_periph(AT91_PIN_PA18, 1);
+ at91_set_A_periph(AT91_PIN_PA19, 1);
+ at91_set_A_periph(AT91_PIN_PA20, 1);
+ }
+ slot_count++;
+ break;
+ default:
+ printk(KERN_ERR
+ "AT91: SD/MMC slot %d not available\n", i);
+ break;
}
- } else {
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA1, 1);
+ if (slot_count) {
+ /* CLK */
+ at91_set_A_periph(AT91_PIN_PA12, 0);
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA0, 1);
- if (data->wire4) {
- at91_set_A_periph(AT91_PIN_PA3, 1);
- at91_set_A_periph(AT91_PIN_PA4, 1);
- at91_set_A_periph(AT91_PIN_PA5, 1);
+ mmc0_data = *data;
+ platform_device_register(&at91sam9263_mmc0_device);
+ }
+ } else if (mmc_id == 1) { /* MCI1 */
+ switch (i) {
+ case 0: /* slot A */
+ /* CMD */
+ at91_set_A_periph(AT91_PIN_PA7, 1);
+ /* DAT0, maybe DAT1..DAT3 */
+ at91_set_A_periph(AT91_PIN_PA8, 1);
+ if (data->slot[i].bus_width == 4) {
+ at91_set_A_periph(AT91_PIN_PA9, 1);
+ at91_set_A_periph(AT91_PIN_PA10, 1);
+ at91_set_A_periph(AT91_PIN_PA11, 1);
+ }
+ slot_count++;
+ break;
+ case 1: /* slot B */
+ /* CMD */
+ at91_set_A_periph(AT91_PIN_PA21, 1);
+ /* DAT0, maybe DAT1..DAT3 */
+ at91_set_A_periph(AT91_PIN_PA22, 1);
+ if (data->slot[i].bus_width == 4) {
+ at91_set_A_periph(AT91_PIN_PA23, 1);
+ at91_set_A_periph(AT91_PIN_PA24, 1);
+ at91_set_A_periph(AT91_PIN_PA25, 1);
+ }
+ slot_count++;
+ break;
+ default:
+ printk(KERN_ERR
+ "AT91: SD/MMC slot %d not available\n", i);
+ break;
+ }
+ if (slot_count) {
+ /* CLK */
+ at91_set_A_periph(AT91_PIN_PA6, 0);
+
+ mmc1_data = *data;
+ platform_device_register(&at91sam9263_mmc1_device);
}
}
-
- mmc0_data = *data;
- platform_device_register(&at91sam9263_mmc0_device);
- } else { /* MCI1 */
- /* CLK */
- at91_set_A_periph(AT91_PIN_PA6, 0);
-
- if (data->slot_b) {
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA21, 1);
-
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA22, 1);
- if (data->wire4) {
- at91_set_A_periph(AT91_PIN_PA23, 1);
- at91_set_A_periph(AT91_PIN_PA24, 1);
- at91_set_A_periph(AT91_PIN_PA25, 1);
- }
- } else {
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA7, 1);
-
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA8, 1);
- if (data->wire4) {
- at91_set_A_periph(AT91_PIN_PA9, 1);
- at91_set_A_periph(AT91_PIN_PA10, 1);
- at91_set_A_periph(AT91_PIN_PA11, 1);
- }
- }
-
- mmc1_data = *data;
- platform_device_register(&at91sam9263_mmc1_device);
}
}
#else
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
+void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
#endif
/* --------------------------------------------------------------------
