diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt
index a994154..a5cb783 100644
--- a/Documentation/feature-removal-schedule.txt
+++ b/Documentation/feature-removal-schedule.txt
@@ -164,15 +164,6 @@
 
 ---------------------------
 
-What:	i2c-isa
-When:	December 2006
-Why:	i2c-isa is a non-sense and doesn't fit in the device driver
-	model. Drivers relying on it are better implemented as platform
-	drivers.
-Who:	Jean Delvare <khali@linux-fr.org>
-
----------------------------
-
 What:	i2c_adapter.list
 When:	July 2007
 Why:	Superfluous, this list duplicates the one maintained by the driver
diff --git a/Documentation/hwmon/abituguru b/Documentation/hwmon/abituguru
index b2c0d61..87ffa0f 100644
--- a/Documentation/hwmon/abituguru
+++ b/Documentation/hwmon/abituguru
@@ -2,7 +2,7 @@
 =======================
 
 Supported chips:
-  * Abit uGuru revision 1-3 (Hardware Monitor part only)
+  * Abit uGuru revision 1 & 2 (Hardware Monitor part only)
     Prefix: 'abituguru'
     Addresses scanned: ISA 0x0E0
     Datasheet: Not available, this driver is based on reverse engineering.
@@ -20,8 +20,8 @@
 	uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8)
 	uGuru 2.2.0.0 ~ 2.2.0.6 (AA8 Fatal1ty)
 	uGuru 2.3.0.0 ~ 2.3.0.9 (AN8)
-	uGuru 3.0.0.0 ~ 3.0.1.2 (AW8, AL8, NI8)
-	uGuru 4.xxxxx?          (AT8 32X) (2)
+	uGuru 3.0.0.0 ~ 3.0.x.x (AW8, AL8, AT8, NI8 SLI, AT8 32X, AN8 32X,
+				 AW9D-MAX) (2)
 	1) For revisions 2 and 3 uGuru's the driver can autodetect the
 	   sensortype (Volt or Temp) for bank1 sensors, for revision 1 uGuru's
 	   this doesnot always work. For these uGuru's the autodection can
@@ -30,8 +30,9 @@
 	   bank1_types=1,1,0,0,0,0,0,2,0,0,0,0,2,0,0,1
 	   You may also need to specify the fan_sensors option for these boards
 	   fan_sensors=5
-	2) The current version of the abituguru driver is known to NOT work
-	   on these Motherboards
+	2) There is a seperate abituguru3 driver for these motherboards,
+	   the abituguru (without the 3 !) driver will not work on these
+	   motherboards (and visa versa)!
 
 Authors:
 	Hans de Goede <j.w.r.degoede@hhs.nl>,
@@ -43,8 +44,10 @@
 -----------------
 
 * force: bool		Force detection. Note this parameter only causes the
-			detection to be skipped, if the uGuru can't be read
-			the module initialization (insmod) will still fail.
+			detection to be skipped, and thus the insmod to
+			succeed. If the uGuru can't be read the actual hwmon
+			driver will not load and thus no hwmon device will get
+			registered.
 * bank1_types: int[]	Bank1 sensortype autodetection override:
 			  -1 autodetect (default)
 			   0 volt sensor
@@ -69,13 +72,15 @@
 Description
 -----------
 
-This driver supports the hardware monitoring features of the Abit uGuru chip
-found on Abit uGuru featuring motherboards (most modern Abit motherboards).
+This driver supports the hardware monitoring features of the first and
+second revision of the Abit uGuru chip found on Abit uGuru featuring
+motherboards (most modern Abit motherboards).
 
-The uGuru chip in reality is a Winbond W83L950D in disguise (despite Abit
-claiming it is "a new microprocessor designed by the ABIT Engineers").
-Unfortunatly this doesn't help since the W83L950D is a generic
-microcontroller with a custom Abit application running on it.
+The first and second revision of the uGuru chip in reality is a Winbond
+W83L950D in disguise (despite Abit claiming it is "a new microprocessor
+designed by the ABIT Engineers"). Unfortunatly this doesn't help since the
+W83L950D is a generic microcontroller with a custom Abit application running
+on it.
 
 Despite Abit not releasing any information regarding the uGuru, Olle
 Sandberg <ollebull@gmail.com> has managed to reverse engineer the sensor part
diff --git a/Documentation/hwmon/abituguru3 b/Documentation/hwmon/abituguru3
new file mode 100644
index 0000000..fa598aa
--- /dev/null
+++ b/Documentation/hwmon/abituguru3
@@ -0,0 +1,65 @@
+Kernel driver abituguru3
+========================
+
+Supported chips:
+  * Abit uGuru revision 3 (Hardware Monitor part, reading only)
+    Prefix: 'abituguru3'
+    Addresses scanned: ISA 0x0E0
+    Datasheet: Not available, this driver is based on reverse engineering.
+    Note:
+	The uGuru is a microcontroller with onboard firmware which programs
+	it to behave as a hwmon IC. There are many different revisions of the
+	firmware and thus effectivly many different revisions of the uGuru.
+	Below is an incomplete list with which revisions are used for which
+	Motherboards:
+	uGuru 1.00    ~ 1.24    (AI7, KV8-MAX3, AN7)
+	uGuru 2.0.0.0 ~ 2.0.4.2 (KV8-PRO)
+	uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8)
+	uGuru 2.3.0.0 ~ 2.3.0.9 (AN8)
+	uGuru 3.0.0.0 ~ 3.0.x.x (AW8, AL8, AT8, NI8 SLI, AT8 32X, AN8 32X,
+				 AW9D-MAX)
+	The abituguru3 driver is only for revison 3.0.x.x motherboards,
+	this driver will not work on older motherboards. For older
+	motherboards use the abituguru (without the 3 !) driver.
+
+Authors:
+	Hans de Goede <j.w.r.degoede@hhs.nl>,
+	(Initial reverse engineering done by Louis Kruger)
+
+
+Module Parameters
+-----------------
+
+* force: bool		Force detection. Note this parameter only causes the
+			detection to be skipped, and thus the insmod to
+			succeed. If the uGuru can't be read the actual hwmon
+			driver will not load and thus no hwmon device will get
+			registered.
+* verbose: bool		Should the driver be verbose?
+			0/off/false  normal output
+			1/on/true    + verbose error reporting (default)
+			Default: 1 (the driver is still in the testing phase)
+
+Description
+-----------
+
+This driver supports the hardware monitoring features of the third revision of
+the Abit uGuru chip, found on recent Abit uGuru featuring motherboards.
+
+The 3rd revision of the uGuru chip in reality is a Winbond W83L951G.
+Unfortunatly this doesn't help since the W83L951G is a generic microcontroller
+with a custom Abit application running on it.
+
+Despite Abit not releasing any information regarding the uGuru revision 3,
+Louis Kruger has managed to reverse engineer the sensor part of the uGuru.
+Without his work this driver would not have been possible.
+
+Known Issues
+------------
+
+The voltage and frequency control parts of the Abit uGuru are not supported,
+neither is writing any of the sensor settings and writing / reading the
+fanspeed control registers (FanEQ)
+
+If you encounter any problems please mail me <j.w.r.degoede@hhs.nl> and
+include the output of: "dmesg | grep abituguru"
diff --git a/Documentation/hwmon/dme1737 b/Documentation/hwmon/dme1737
new file mode 100644
index 0000000..1a0f3d6
--- /dev/null
+++ b/Documentation/hwmon/dme1737
@@ -0,0 +1,257 @@
+Kernel driver dme1737
+=====================
+
+Supported chips:
+  * SMSC DME1737 and compatibles (like Asus A8000)
+    Prefix: 'dme1737'
+    Addresses scanned: I2C 0x2c, 0x2d, 0x2e
+    Datasheet: Provided by SMSC upon request and under NDA
+
+Authors:
+    Juerg Haefliger <juergh@gmail.com>
+
+
+Module Parameters
+-----------------
+
+* force_start: bool	Enables the monitoring of voltage, fan and temp inputs
+			and PWM output control functions. Using this parameter
+			shouldn't be required since the BIOS usually takes care
+			of this.
+
+Note that there is no need to use this parameter if the driver loads without
+complaining. The driver will say so if it is necessary.
+
+
+Description
+-----------
+
+This driver implements support for the hardware monitoring capabilities of the
+SMSC DME1737 and Asus A8000 (which are the same) Super-I/O chips. This chip
+features monitoring of 3 temp sensors temp[1-3] (2 remote diodes and 1
+internal), 7 voltages in[0-6] (6 external and 1 internal) and 6 fan speeds
+fan[1-6]. Additionally, the chip implements 5 PWM outputs pwm[1-3,5-6] for
+controlling fan speeds both manually and automatically.
+
+Fan[3-6] and pwm[3,5-6] are optional features and their availability is
+dependent on the configuration of the chip. The driver will detect which
+features are present during initialization and create the sysfs attributes
+accordingly.
+
+
+Voltage Monitoring
+------------------
+
+The voltage inputs are sampled with 12-bit resolution and have internal
+scaling resistors. The values returned by the driver therefore reflect true
+millivolts and don't need scaling. The voltage inputs are mapped as follows
+(the last column indicates the input ranges):
+
+	in0: +5VTR	(+5V standby)		0V - 6.64V
+	in1: Vccp	(processor core)	0V - 3V
+	in2: VCC	(internal +3.3V)	0V - 4.38V
+	in3: +5V				0V - 6.64V
+	in4: +12V				0V - 16V
+	in5: VTR	(+3.3V standby)		0V - 4.38V
+	in6: Vbat	(+3.0V)			0V - 4.38V
+
+Each voltage input has associated min and max limits which trigger an alarm
+when crossed.
+
+
+Temperature Monitoring
+----------------------
+
+Temperatures are measured with 12-bit resolution and reported in millidegree
+Celsius. The chip also features offsets for all 3 temperature inputs which -
+when programmed - get added to the input readings. The chip does all the
+scaling by itself and the driver therefore reports true temperatures that don't
+need any user-space adjustments. The temperature inputs are mapped as follows
+(the last column indicates the input ranges):
+
+	temp1: Remote diode 1 (3904 type) temperature	-127C - +127C
+	temp2: DME1737 internal temperature		-127C - +127C
+	temp3: Remote diode 2 (3904 type) temperature	-127C - +127C
+
+Each temperature input has associated min and max limits which trigger an alarm
+when crossed. Additionally, each temperature input has a fault attribute that
+returns 1 when a faulty diode or an unconnected input is detected and 0
+otherwise.
+
+
+Fan Monitoring
+--------------
+
+Fan RPMs are measured with 16-bit resolution. The chip provides inputs for 6
+fan tachometers. All 6 inputs have an associated min limit which triggers an
+alarm when crossed. Fan inputs 1-4 provide type attributes that need to be set
+to the number of pulses per fan revolution that the connected tachometer
+generates. Supported values are 1, 2, and 4. Fan inputs 5-6 only support fans
+that generate 2 pulses per revolution. Fan inputs 5-6 also provide a max
+attribute that needs to be set to the maximum attainable RPM (fan at 100% duty-
+cycle) of the input. The chip adjusts the sampling rate based on this value.
+
+
+PWM Output Control
+------------------
+
+This chip features 5 PWM outputs. PWM outputs 1-3 are associated with fan
+inputs 1-3 and PWM outputs 5-6 are associated with fan inputs 5-6. PWM outputs
+1-3 can be configured to operate either in manual or automatic mode by setting
+the appropriate enable attribute accordingly. PWM outputs 5-6 can only operate
+in manual mode, their enable attributes are therefore read-only. When set to
+manual mode, the fan speed is set by writing the duty-cycle value to the
+appropriate PWM attribute. In automatic mode, the PWM attribute returns the
+current duty-cycle as set by the fan controller in the chip. All PWM outputs
+support the setting of the output frequency via the freq attribute.
+
+In automatic mode, the chip supports the setting of the PWM ramp rate which
+defines how fast the PWM output is adjusting to changes of the associated
+temperature input. Associating PWM outputs to temperature inputs is done via
+temperature zones. The chip features 3 zones whose assignments to temperature
+inputs is static and determined during initialization. These assignments can
+be retrieved via the zone[1-3]_auto_channels_temp attributes. Each PWM output
+is assigned to one (or hottest of multiple) temperature zone(s) through the
+pwm[1-3]_auto_channels_zone attributes. Each PWM output has 3 distinct output
+duty-cycles: full, low, and min. Full is internally hard-wired to 255 (100%)
+and low and min can be programmed via pwm[1-3]_auto_point1_pwm and
+pwm[1-3]_auto_pwm_min, respectively. The thermal thresholds of the zones are
+programmed via zone[1-3]_auto_point[1-3]_temp and
+zone[1-3]_auto_point1_temp_hyst:
+
+	pwm[1-3]_auto_point2_pwm	full-speed duty-cycle (255, i.e., 100%)
+	pwm[1-3]_auto_point1_pwm	low-speed duty-cycle
+	pwm[1-3]_auto_pwm_min		min-speed duty-cycle
+
+	zone[1-3]_auto_point3_temp	full-speed temp (all outputs)
+	zone[1-3]_auto_point2_temp	full-speed temp
+	zone[1-3]_auto_point1_temp	low-speed temp
+	zone[1-3]_auto_point1_temp_hyst	min-speed temp
+
+The chip adjusts the output duty-cycle linearly in the range of auto_point1_pwm
+to auto_point2_pwm if the temperature of the associated zone is between
+auto_point1_temp and auto_point2_temp. If the temperature drops below the
+auto_point1_temp_hyst value, the output duty-cycle is set to the auto_pwm_min
+value which only supports two values: 0 or auto_point1_pwm. That means that the
+fan either turns completely off or keeps spinning with the low-speed
+duty-cycle. If any of the temperatures rise above the auto_point3_temp value,
+all PWM outputs are set to 100% duty-cycle.
+
+Following is another representation of how the chip sets the output duty-cycle
+based on the temperature of the associated thermal zone:
+
+			Duty-Cycle	Duty-Cycle
+	Temperature	Rising Temp	Falling Temp
+	-----------	-----------	------------
+	full-speed	full-speed	full-speed
+
+			< linearly adjusted duty-cycle >
+
+	low-speed	low-speed	low-speed
+			min-speed	low-speed
+	min-speed	min-speed	min-speed
+			min-speed	min-speed
+
+
+Sysfs Attributes
+----------------
+
+Following is a list of all sysfs attributes that the driver provides, their
+permissions and a short description:
+
+Name				Perm	Description
+----				----	-----------
+cpu0_vid			RO	CPU core reference voltage in
+					millivolts.
+vrm				RW	Voltage regulator module version
+					number.
+
+in[0-6]_input			RO	Measured voltage in millivolts.
+in[0-6]_min			RW	Low limit for voltage input.
+in[0-6]_max			RW	High limit for voltage input.
+in[0-6]_alarm			RO	Voltage input alarm. Returns 1 if
+					voltage input is or went outside the
+					associated min-max range, 0 otherwise.
+
+temp[1-3]_input			RO	Measured temperature in millidegree
+					Celsius.
+temp[1-3]_min			RW	Low limit for temp input.
+temp[1-3]_max			RW	High limit for temp input.
+temp[1-3]_offset		RW	Offset for temp input. This value will
+					be added by the chip to the measured
+					temperature.
+temp[1-3]_alarm			RO	Alarm for temp input. Returns 1 if temp
+					input is or went outside the associated
+					min-max range, 0 otherwise.
+temp[1-3]_fault			RO	Temp input fault. Returns 1 if the chip
+					detects a faulty thermal diode or an
+					unconnected temp input, 0 otherwise.
+
+zone[1-3]_auto_channels_temp	RO	Temperature zone to temperature input
+					mapping. This attribute is a bitfield
+					and supports the following values:
+						1: temp1
+						2: temp2
+						4: temp3
+zone[1-3]_auto_point1_temp_hyst	RW	Auto PWM temp point1 hysteresis. The
+					output of the corresponding PWM is set
+					to the pwm_auto_min value if the temp
+					falls below the auto_point1_temp_hyst
+					value.
+zone[1-3]_auto_point[1-3]_temp	RW	Auto PWM temp points. Auto_point1 is
+					the low-speed temp, auto_point2 is the
+					full-speed temp, and auto_point3 is the
+					temp at which all PWM outputs are set
+					to full-speed (100% duty-cycle).
+
+fan[1-6]_input			RO	Measured fan speed in RPM.
+fan[1-6]_min			RW	Low limit for fan input.
+fan[1-6]_alarm			RO	Alarm for fan input. Returns 1 if fan
+					input is or went below the associated
+					min value, 0 otherwise.
+fan[1-4]_type			RW	Type of attached fan. Expressed in
+					number of pulses per revolution that
+					the fan generates. Supported values are
+					1, 2, and 4.
+fan[5-6]_max			RW	Max attainable RPM at 100% duty-cycle.
+					Required for chip to adjust the
+					sampling rate accordingly.
+
+pmw[1-3,5-6]			RO/RW	Duty-cycle of PWM output. Supported
+					values are 0-255 (0%-100%). Only
+					writeable if the associated PWM is in
+					manual mode.
+pwm[1-3]_enable			RW	Enable of PWM outputs 1-3. Supported
+					values are:
+						 0: turned off (output @ 100%)
+						 1: manual mode
+						 2: automatic mode
+pwm[5-6]_enable			RO	Enable of PWM outputs 5-6. Always
+					returns 1 since these 2 outputs are
+					hard-wired to manual mode.
+pmw[1-3,5-6]_freq		RW	Frequency of PWM output. Supported
+					values are in the range 11Hz-30000Hz
+					(default is 25000Hz).
+pmw[1-3]_ramp_rate		RW	Ramp rate of PWM output. Determines how
+					fast the PWM duty-cycle will change
+					when the PWM is in automatic mode.
+					Expressed in ms per PWM step. Supported
+					values are in the range 0ms-206ms
+					(default is 0, which means the duty-
+					cycle changes instantly).
+pwm[1-3]_auto_channels_zone	RW	PWM output to temperature zone mapping.
+					This attribute is a bitfield and
+					supports the following values:
+						1: zone1
+						2: zone2
+						4: zone3
+						6: highest of zone[2-3]
+						7: highest of zone[1-3]
+pwm[1-3]_auto_pwm_min		RW	Auto PWM min pwm. Minimum PWM duty-
+					cycle. Supported values are 0 or
+					auto_point1_pwm.
+pwm[1-3]_auto_point1_pwm	RW	Auto PWM pwm point. Auto_point1 is the
+					low-speed duty-cycle.
+pwm[1-3]_auto_point2_pwm	RO	Auto PWM pwm point. Auto_point2 is the
+					full-speed duty-cycle which is hard-
+					wired to 255 (100% duty-cycle).
diff --git a/Documentation/hwmon/f71805f b/Documentation/hwmon/f71805f
index bfd0f15..94e0d2c 100644
--- a/Documentation/hwmon/f71805f
+++ b/Documentation/hwmon/f71805f
@@ -5,11 +5,11 @@
   * Fintek F71805F/FG
     Prefix: 'f71805f'
     Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Provided by Fintek on request
+    Datasheet: Available from the Fintek website
   * Fintek F71872F/FG
     Prefix: 'f71872f'
     Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Provided by Fintek on request
+    Datasheet: Available from the Fintek website
 
 Author: Jean Delvare <khali@linux-fr.org>
 
@@ -128,7 +128,9 @@
 When the PWM method is used, you can select the operating frequency,
 from 187.5 kHz (default) to 31 Hz. The best frequency depends on the
 fan model. As a rule of thumb, lower frequencies seem to give better
-control, but may generate annoying high-pitch noise. Fintek recommends
+control, but may generate annoying high-pitch noise. So a frequency just
+above the audible range, such as 25 kHz, may be a good choice; if this
+doesn't give you good linear control, try reducing it. Fintek recommends
 not going below 1 kHz, as the fan tachometers get confused by lower
 frequencies as well.
 
@@ -136,16 +138,23 @@
 corresponds to a pwm value of 106 for the driver. The driver doesn't
 enforce this limit though.
 
-Three different fan control modes are supported:
+Three different fan control modes are supported; the mode number is written
+to the pwm<n>_enable file.
 
-* Manual mode
-  You ask for a specific PWM duty cycle or DC voltage.
+* 1: Manual mode
+  You ask for a specific PWM duty cycle or DC voltage by writing to the
+  pwm<n> file.
 
-* Fan speed mode
-  You ask for a specific fan speed. This mode assumes that pwm1
-  corresponds to fan1, pwm2 to fan2 and pwm3 to fan3.
+* 2: Temperature mode
+  You define 3 temperature/fan speed trip points using the
+  pwm<n>_auto_point<m>_temp and _fan files. These define a staircase
+  relationship between temperature and fan speed with two additional points
+  interpolated between the values that you define. When the temperature
+  is below auto_point1_temp the fan is switched off.
 
-* Temperature mode
-  You define 3 temperature/fan speed trip points, and the fan speed is
-  adjusted depending on the measured temperature, using interpolation.
-  This mode is not yet supported by the driver.
+* 3: Fan speed mode
+  You ask for a specific fan speed by writing to the fan<n>_target file.
+
+Both of the automatic modes require that pwm1 corresponds to fan1, pwm2 to
+fan2 and pwm3 to fan3. Temperature mode also requires that temp1 corresponds
+to pwm1 and fan1, etc.
diff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87
index c0528d6..81ecc7e 100644
--- a/Documentation/hwmon/it87
+++ b/Documentation/hwmon/it87
@@ -12,11 +12,12 @@
     Addresses scanned: from Super I/O config space (8 I/O ports)
     Datasheet: Publicly available at the ITE website
                http://www.ite.com.tw/
-  * IT8716F
+  * IT8716F/IT8726F
     Prefix: 'it8716'
     Addresses scanned: from Super I/O config space (8 I/O ports)
     Datasheet: Publicly available at the ITE website
                http://www.ite.com.tw/product_info/file/pc/IT8716F_V0.3.ZIP
+               http://www.ite.com.tw/product_info/file/pc/IT8726F_V0.3.pdf
   * IT8718F
     Prefix: 'it8718'
     Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -68,7 +69,7 @@
 -----------
 
 This driver implements support for the IT8705F, IT8712F, IT8716F,
-IT8718F and SiS950 chips.
+IT8718F, IT8726F and SiS950 chips.
 
 These chips are 'Super I/O chips', supporting floppy disks, infrared ports,
 joysticks and other miscellaneous stuff. For hardware monitoring, they
@@ -97,6 +98,10 @@
 revisions. For now, the driver only uses the 16-bit mode on the
 IT8716F and IT8718F.
 
+The IT8726F is just bit enhanced IT8716F with additional hardware
+for AMD power sequencing. Therefore the chip will appear as IT8716F
+to userspace applications.
+
 Temperatures are measured in degrees Celsius. An alarm is triggered once
 when the Overtemperature Shutdown limit is crossed.
 
diff --git a/Documentation/hwmon/lm90 b/Documentation/hwmon/lm90
index 438cb24..aa4a0ec 100644
--- a/Documentation/hwmon/lm90
+++ b/Documentation/hwmon/lm90
@@ -48,6 +48,18 @@
     Addresses scanned: I2C 0x4c, 0x4d (unsupported 0x4e)
     Datasheet: Publicly available at the Maxim website
                http://www.maxim-ic.com/quick_view2.cfm/qv_pk/2578
+  * Maxim MAX6680
+    Prefix: 'max6680'
+    Addresses scanned: I2C 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
+                           0x4c, 0x4d and 0x4e
+    Datasheet: Publicly available at the Maxim website
+               http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3370
+  * Maxim MAX6681
+    Prefix: 'max6680'
+    Addresses scanned: I2C 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
+                           0x4c, 0x4d and 0x4e
+    Datasheet: Publicly available at the Maxim website
+               http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3370
 
 
 Author: Jean Delvare <khali@linux-fr.org>
@@ -59,11 +71,15 @@
 The LM90 is a digital temperature sensor. It senses its own temperature as
 well as the temperature of up to one external diode. It is compatible
 with many other devices such as the LM86, the LM89, the LM99, the ADM1032,
-the MAX6657, MAX6658 and the MAX6659 all of which are supported by this driver.
-Note that there is no easy way to differentiate between the last three
-variants. The extra address and features of the MAX6659 are not supported by
-this driver. Additionally, the ADT7461 is supported if found in ADM1032
-compatibility mode.
+the MAX6657, MAX6658, MAX6659, MAX6680 and the MAX6681 all of which are
+supported by this driver.
+
+Note that there is no easy way to differentiate between the MAX6657,
+MAX6658 and MAX6659 variants. The extra address and features of the
+MAX6659 are not supported by this driver. The MAX6680 and MAX6681 only
+differ in their pinout, therefore they obviously can't (and don't need to)
+be distinguished. Additionally, the ADT7461 is supported if found in
+ADM1032 compatibility mode.
 
 The specificity of this family of chipsets over the ADM1021/LM84
 family is that it features critical limits with hysteresis, and an
@@ -93,18 +109,22 @@
   * ALERT is triggered by open remote sensor.
   * SMBus PEC support for Write Byte and Receive Byte transactions.
 
-ADT7461
+ADT7461:
   * Extended temperature range (breaks compatibility)
   * Lower resolution for remote temperature
 
 MAX6657 and MAX6658:
   * Remote sensor type selection
 
-MAX6659
+MAX6659:
   * Selectable address
   * Second critical temperature limit
   * Remote sensor type selection
 
+MAX6680 and MAX6681:
+  * Selectable address
+  * Remote sensor type selection
+
 All temperature values are given in degrees Celsius. Resolution
 is 1.0 degree for the local temperature, 0.125 degree for the remote
 temperature.
@@ -141,7 +161,7 @@
 Additionally, the ADM1032 doesn't support SMBus Send Byte with PEC.
 Instead, it will try to write the PEC value to the register (because the
 SMBus Send Byte transaction with PEC is similar to a Write Byte transaction
-without PEC), which is not what we want. Thus, PEC is explicitely disabled
+without PEC), which is not what we want. Thus, PEC is explicitly disabled
 on SMBus Send Byte transactions in the lm90 driver.
 
 PEC on byte data transactions represents a significant increase in bandwidth
diff --git a/Documentation/hwmon/lm93 b/Documentation/hwmon/lm93
new file mode 100644
index 0000000..4e4a1dc
--- /dev/null
+++ b/Documentation/hwmon/lm93
@@ -0,0 +1,412 @@
+Kernel driver lm93
+==================
+
+Supported chips:
+  * National Semiconductor LM93
+    Prefix 'lm93'
+    Addresses scanned: I2C 0x2c-0x2e
+    Datasheet: http://www.national.com/ds.cgi/LM/LM93.pdf
+
+Author:
+	Mark M. Hoffman <mhoffman@lightlink.com>
+	Ported to 2.6 by Eric J. Bowersox <ericb@aspsys.com>
+	Adapted to 2.6.20 by Carsten Emde <ce@osadl.org>
+	Modified for mainline integration by Hans J. Koch <hjk@linutronix.de>
+
+Module Parameters
+-----------------
+
+(specific to LM93)
+* init: integer
+  Set to non-zero to force some initializations (default is 0).
+* disable_block: integer
+  A "0" allows SMBus block data transactions if the host supports them.  A "1"
+  disables SMBus block data transactions.  The default is 0.
+* vccp_limit_type: integer array (2)
+  Configures in7 and in8 limit type, where 0 means absolute and non-zero
+  means relative.  "Relative" here refers to "Dynamic Vccp Monitoring using
+  VID" from the datasheet.  It greatly simplifies the interface to allow
+  only one set of limits (absolute or relative) to be in operation at a
+  time (even though the hardware is capable of enabling both).  There's
+  not a compelling use case for enabling both at once, anyway.  The default
+  is "0,0".
+* vid_agtl: integer
+  A "0" configures the VID pins for V(ih) = 2.1V min, V(il) = 0.8V max.
+  A "1" configures the VID pins for V(ih) = 0.8V min, V(il) = 0.4V max.
+  (The latter setting is referred to as AGTL+ Compatible in the datasheet.)
+  I.e. this parameter controls the VID pin input thresholds; if your VID
+  inputs are not working, try changing this.  The default value is "0".
+
+(common among sensor drivers)
+* force: short array (min = 1, max = 48)
+  List of adapter,address pairs to assume to be present.  Autodetection
+  of the target device will still be attempted.  Use one of the more
+  specific force directives below if this doesn't detect the device.
+* force_lm93: short array (min = 1, max = 48)
+  List of adapter,address pairs which are unquestionably assumed to contain
+  a 'lm93' chip
+* ignore: short array (min = 1, max = 48)
+  List of adapter,address pairs not to scan
+* ignore_range: short array (min = 1, max = 48)
+  List of adapter,start-addr,end-addr triples not to scan
+* probe: short array (min = 1, max = 48)
+  List of adapter,address pairs to scan additionally
+* probe_range: short array (min = 1, max = 48)
+  List of adapter,start-addr,end-addr triples to scan additionally
+
+
+Hardware Description
+--------------------
+
+(from the datasheet)
+
+The LM93, hardware monitor, has a two wire digital interface compatible with
+SMBus 2.0. Using an 8-bit ADC, the LM93 measures the temperature of two remote
+diode connected transistors as well as its own die and 16 power supply
+voltages. To set fan speed, the LM93 has two PWM outputs that are each
+controlled by up to four temperature zones. The fancontrol algorithm is lookup
+table based. The LM93 includes a digital filter that can be invoked to smooth
+temperature readings for better control of fan speed. The LM93 has four
+tachometer inputs to measure fan speed. Limit and status registers for all
+measured values are included. The LM93 builds upon the functionality of
+previous motherboard management ASICs and uses some of the LM85 s features
+(i.e. smart tachometer mode). It also adds measurement and control support
+for dynamic Vccp monitoring and PROCHOT. It is designed to monitor a dual
+processor Xeon class motherboard with a minimum of external components.
+
+
+Driver Description
+------------------
+
+This driver implements support for the National Semiconductor LM93.
+
+
+User Interface
+--------------
+
+#PROCHOT:
+
+The LM93 can monitor two #PROCHOT signals.  The results are found in the
+sysfs files prochot1, prochot2, prochot1_avg, prochot2_avg, prochot1_max,
+and prochot2_max.  prochot1_max and prochot2_max contain the user limits
+for #PROCHOT1 and #PROCHOT2, respectively.  prochot1 and prochot2 contain
+the current readings for the most recent complete time interval.  The
+value of prochot1_avg and prochot2_avg is something like a 2 period
+exponential moving average (but not quite - check the datasheet). Note
+that this third value is calculated by the chip itself.  All values range
+from 0-255 where 0 indicates no throttling, and 255 indicates > 99.6%.
+
+The monitoring intervals for the two #PROCHOT signals is also configurable.
+These intervals can be found in the sysfs files prochot1_interval and
+prochot2_interval.  The values in these files specify the intervals for
+#P1_PROCHOT and #P2_PROCHOT, respectively.  Selecting a value not in this
+list will cause the driver to use the next largest interval.  The available
+intervals are:
+
+#PROCHOT intervals: 0.73, 1.46, 2.9, 5.8, 11.7, 23.3, 46.6, 93.2, 186, 372
+
+It is possible to configure the LM93 to logically short the two #PROCHOT
+signals.  I.e. when #P1_PROCHOT is asserted, the LM93 will automatically
+assert #P2_PROCHOT, and vice-versa.  This mode is enabled by writing a
+non-zero integer to the sysfs file prochot_short.
+
+The LM93 can also override the #PROCHOT pins by driving a PWM signal onto
+one or both of them.  When overridden, the signal has a period of 3.56 mS,
+a minimum pulse width of 5 clocks (at 22.5kHz => 6.25% duty cycle), and
+a maximum pulse width of 80 clocks (at 22.5kHz => 99.88% duty cycle).
+
+The sysfs files prochot1_override and prochot2_override contain boolean
+intgers which enable or disable the override function for #P1_PROCHOT and
+#P2_PROCHOT, respectively.  The sysfs file prochot_override_duty_cycle
+contains a value controlling the duty cycle for the PWM signal used when
+the override function is enabled.  This value ranges from 0 to 15, with 0
+indicating minimum duty cycle and 15 indicating maximum.
+
+#VRD_HOT:
+
+The LM93 can monitor two #VRD_HOT signals. The results are found in the
+sysfs files vrdhot1 and vrdhot2. There is one value per file: a boolean for
+which 1 indicates #VRD_HOT is asserted and 0 indicates it is negated. These
+files are read-only.
+
+Smart Tach Mode:
+
+(from the datasheet)
+
+	If a fan is driven using a low-side drive PWM, the tachometer
+	output of the fan is corrupted. The LM93 includes smart tachometer
+	circuitry that allows an accurate tachometer reading to be
+	achieved despite the signal corruption.  In smart tach mode all
+	four signals are measured within 4 seconds.
+
+Smart tach mode is enabled by the driver by writing 1 or 2 (associating the
+the fan tachometer with a pwm) to the sysfs file fan<n>_smart_tach.  A zero
+will disable the function for that fan.  Note that Smart tach mode cannot be
+enabled if the PWM output frequency is 22500 Hz (see below).
+
+Manual PWM:
+
+The LM93 has a fixed or override mode for the two PWM outputs (although, there
+are still some conditions that will override even this mode - see section
+15.10.6 of the datasheet for details.)  The sysfs files pwm1_override
+and pwm2_override are used to enable this mode; each is a boolean integer
+where 0 disables and 1 enables the manual control mode.  The sysfs files pwm1
+and pwm2 are used to set the manual duty cycle; each is an integer (0-255)
+where 0 is 0% duty cycle, and 255 is 100%.  Note that the duty cycle values
+are constrained by the hardware. Selecting a value which is not available
+will cause the driver to use the next largest value.  Also note: when manual
+PWM mode is disabled, the value of pwm1 and pwm2 indicates the current duty
+cycle chosen by the h/w.
+
+PWM Output Frequency:
+
+The LM93 supports several different frequencies for the PWM output channels.
+The sysfs files pwm1_freq and pwm2_freq are used to select the frequency. The
+frequency values are constrained by the hardware.  Selecting a value which is
+not available will cause the driver to use the next largest value.  Also note
+that this parameter has implications for the Smart Tach Mode (see above).
+
+PWM Output Frequencies: 12, 36, 48, 60, 72, 84, 96, 22500 (h/w default)
+
+Automatic PWM:
+
+The LM93 is capable of complex automatic fan control, with many different
+points of configuration.  To start, each PWM output can be bound to any
+combination of eight control sources.  The final PWM is the largest of all
+individual control sources to which the PWM output is bound.
+
+The eight control sources are: temp1-temp4 (aka "zones" in the datasheet),
+#PROCHOT 1 & 2, and #VRDHOT 1 & 2.  The bindings are expressed as a bitmask
+in the sysfs files pwm<n>_auto_channels, where a "1" enables the binding, and
+ a "0" disables it. The h/w default is 0x0f (all temperatures bound).
+
+	0x01 - Temp 1
+	0x02 - Temp 2
+	0x04 - Temp 3
+	0x08 - Temp 4
+	0x10 - #PROCHOT 1
+	0x20 - #PROCHOT 2
+	0x40 - #VRDHOT 1
+	0x80 - #VRDHOT 2
+
+The function y = f(x) takes a source temperature x to a PWM output y.  This
+function of the LM93 is derived from a base temperature and a table of 12
+temperature offsets.  The base temperature is expressed in degrees C in the
+sysfs files temp<n>_auto_base.  The offsets are expressed in cumulative
+degrees C, with the value of offset <i> for temperature value <n> being
+contained in the file temp<n>_auto_offset<i>.  E.g. if the base temperature
+is 40C:
+
+     offset #	temp<n>_auto_offset<i>	range		pwm
+	 1		0		-		 25.00%
+	 2		0		-		 28.57%
+	 3		1		40C - 41C	 32.14%
+	 4		1		41C - 42C	 35.71%
+	 5		2		42C - 44C	 39.29%
+	 6		2		44C - 46C	 42.86%
+	 7		2		48C - 50C	 46.43%
+	 8		2		50C - 52C	 50.00%
+	 9		2		52C - 54C	 53.57%
+	10		2		54C - 56C	 57.14%
+	11		2		56C - 58C	 71.43%
+	12		2		58C - 60C	 85.71%
+					> 60C		100.00%
+
+Valid offsets are in the range 0C <= x <= 7.5C in 0.5C increments.
+
+There is an independent base temperature for each temperature channel. Note,
+however, there are only two tables of offsets: one each for temp[12] and
+temp[34].  Therefore, any change to e.g. temp1_auto_offset<i> will also
+affect temp2_auto_offset<i>.
+
+The LM93 can also apply hysteresis to the offset table, to prevent unwanted
+oscillation between two steps in the offsets table.  These values are found in
+the sysfs files temp<n>_auto_offset_hyst.  The value in this file has the
+same representation as in temp<n>_auto_offset<i>.
+
+If a temperature reading falls below the base value for that channel, the LM93
+will use the minimum PWM value.  These values are found in the sysfs files
+temp<n>_auto_pwm_min.  Note, there are only two minimums: one each for temp[12]
+and temp[34].  Therefore, any change to e.g. temp1_auto_pwm_min will also
+affect temp2_auto_pwm_min.
+
+PWM Spin-Up Cycle:
+
+A spin-up cycle occurs when a PWM output is commanded from 0% duty cycle to
+some value > 0%.  The LM93 supports a minimum duty cycle during spin-up.  These
+values are found in the sysfs files pwm<n>_auto_spinup_min. The value in this
+file has the same representation as other PWM duty cycle values. The
+duration of the spin-up cycle is also configurable.  These values are found in
+the sysfs files pwm<n>_auto_spinup_time. The value in this file is
+the spin-up time in seconds.  The available spin-up times are constrained by
+the hardware.  Selecting a value which is not available will cause the driver
+to use the next largest value.
+
+Spin-up Durations: 0 (disabled, h/w default), 0.1, 0.25, 0.4, 0.7, 1.0,
+		   2.0, 4.0
+
+#PROCHOT and #VRDHOT PWM Ramping:
+
+If the #PROCHOT or #VRDHOT signals are asserted while bound to a PWM output
+channel, the LM93 will ramp the PWM output up to 100% duty cycle in discrete
+steps. The duration of each step is configurable. There are two files, with
+one value each in seconds: pwm_auto_prochot_ramp and pwm_auto_vrdhot_ramp.
+The available ramp times are constrained by the hardware.  Selecting a value
+which is not available will cause the driver to use the next largest value.
+
+Ramp Times: 0 (disabled, h/w default) to 0.75 in 0.05 second intervals
+
+Fan Boost:
+
+For each temperature channel, there is a boost temperature: if the channel
+exceeds this limit, the LM93 will immediately drive both PWM outputs to 100%.
+This limit is expressed in degrees C in the sysfs files temp<n>_auto_boost.
+There is also a hysteresis temperature for this function: after the boost
+limit is reached, the temperature channel must drop below this value before
+the boost function is disabled.  This temperature is also expressed in degrees
+C in the sysfs files temp<n>_auto_boost_hyst.
+
+GPIO Pins:
+
+The LM93 can monitor the logic level of four dedicated GPIO pins as well as the
+four tach input pins.  GPIO0-GPIO3 correspond to (fan) tach 1-4, respectively.
+All eight GPIOs are read by reading the bitmask in the sysfs file gpio.  The
+LSB is GPIO0, and the MSB is GPIO7.
+
+
+LM93 Unique sysfs Files
+-----------------------
+
+	file			description
+	-------------------------------------------------------------
+
+	prochot<n>		current #PROCHOT %
+
+	prochot<n>_avg		moving average #PROCHOT %
+
+	prochot<n>_max		limit #PROCHOT %
+
+	prochot_short		enable or disable logical #PROCHOT pin short
+
+	prochot<n>_override	force #PROCHOT assertion as PWM
+
+	prochot_override_duty_cycle
+				duty cycle for the PWM signal used when
+				#PROCHOT is overridden
+
+	prochot<n>_interval	#PROCHOT PWM sampling interval
+
+	vrdhot<n>		0 means negated, 1 means asserted
+
+	fan<n>_smart_tach	enable or disable smart tach mode
+
+	pwm<n>_auto_channels	select control sources for PWM outputs
+
+	pwm<n>_auto_spinup_min	minimum duty cycle during spin-up
+
+	pwm<n>_auto_spinup_time	duration of spin-up
+
+	pwm_auto_prochot_ramp	ramp time per step when #PROCHOT asserted
+
+	pwm_auto_vrdhot_ramp	ramp time per step when #VRDHOT asserted
+
+	temp<n>_auto_base	temperature channel base
+
+	temp<n>_auto_offset[1-12]
+				temperature channel offsets
+
+	temp<n>_auto_offset_hyst
+				temperature channel offset hysteresis
+
+	temp<n>_auto_boost	temperature channel boost (PWMs to 100%) limit
+
+	temp<n>_auto_boost_hyst	temperature channel boost hysteresis
+
+	gpio			input state of 8 GPIO pins; read-only
+
+
+Sample Configuration File
+-------------------------
+
+Here is a sample LM93 chip config for sensors.conf:
+
+---------- cut here ----------
+chip "lm93-*"
+
+# VOLTAGE INPUTS
+
+	# labels and scaling based on datasheet recommendations
+	label in1	"+12V1"
+	compute in1	@ * 12.945, @ / 12.945
+	set in1_min	12 * 0.90
+	set in1_max	12 * 1.10
+
+	label in2	"+12V2"
+	compute in2	@ * 12.945, @ / 12.945
+	set in2_min	12 * 0.90
+	set in2_max	12 * 1.10
+
+	label in3	"+12V3"
+	compute in3	@ * 12.945, @ / 12.945
+	set in3_min	12 * 0.90
+	set in3_max	12 * 1.10
+
+	label in4	"FSB_Vtt"
+
+	label in5	"3GIO"
+
+	label in6	"ICH_Core"
+
+	label in7	"Vccp1"
+
+	label in8	"Vccp2"
+
+	label in9	"+3.3V"
+	set in9_min	3.3 * 0.90
+	set in9_max	3.3 * 1.10
+
+	label in10	"+5V"
+	set in10_min	5.0 * 0.90
+	set in10_max	5.0 * 1.10
+
+	label in11	"SCSI_Core"
+
+	label in12	"Mem_Core"
+
+	label in13	"Mem_Vtt"
+
+	label in14	"Gbit_Core"
+
+	# Assuming R1/R2 = 4.1143, and 3.3V reference
+	# -12V = (4.1143 + 1) * (@ - 3.3) + 3.3
+	label in15	"-12V"
+	compute in15 @ * 5.1143 - 13.57719, (@ + 13.57719) / 5.1143
+	set in15_min	-12 * 0.90
+	set in15_max	-12 * 1.10
+
+	label in16	"+3.3VSB"
+	set in16_min	3.3 * 0.90
+	set in16_max	3.3 * 1.10
+
+# TEMPERATURE INPUTS
+
+	label temp1	"CPU1"
+	label temp2	"CPU2"
+	label temp3	"LM93"
+
+# TACHOMETER INPUTS
+
+	label fan1	"Fan1"
+	set fan1_min	3000
+	label fan2	"Fan2"
+	set fan2_min	3000
+	label fan3	"Fan3"
+	set fan3_min	3000
+	label fan4	"Fan4"
+	set fan4_min	3000
+
+# PWM OUTPUTS
+
+	label pwm1	"CPU1"
+	label pwm2	"CPU2"
+
diff --git a/Documentation/hwmon/smsc47b397 b/Documentation/hwmon/smsc47b397
index 20682f1..3a43b69 100644
--- a/Documentation/hwmon/smsc47b397
+++ b/Documentation/hwmon/smsc47b397
@@ -4,6 +4,7 @@
 Supported chips:
   * SMSC LPC47B397-NC
   * SMSC SCH5307-NS
+  * SMSC SCH5317
     Prefix: 'smsc47b397'
     Addresses scanned: none, address read from Super I/O config space
     Datasheet: In this file
@@ -18,8 +19,8 @@
 provided by Craig Kelly (In-Store Broadcast Network) and edited/corrected
 by Mark M. Hoffman <mhoffman@lightlink.com>.
 
-[1] And SMSC SCH5307-NS, which has a different device ID but is otherwise
-compatible.
+[1] And SMSC SCH5307-NS and SCH5317, which have different device IDs but are
+otherwise compatible.
 
 * * * * *
 
@@ -131,7 +132,7 @@
 The registers of interest for identifying the SIO on the dc7100 are Device ID
 (0x20) and Device Rev  (0x21).
 
-The Device ID will read 0x6F (for SCH5307-NS, 0x81)
+The Device ID will read 0x6F (0x81 for SCH5307-NS, and 0x85 for SCH5317)
 The Device Rev currently reads 0x01
 
 Obtaining the HWM Base Address.
diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface
index a9a18ad..b3a9e1b 100644
--- a/Documentation/hwmon/sysfs-interface
+++ b/Documentation/hwmon/sysfs-interface
@@ -172,11 +172,10 @@
 		255 is max or 100%.
 
 pwm[1-*]_enable
-		Switch PWM on and off.
-		Not always present even if pwmN is.
-		0: turn off
-		1: turn on in manual mode
-		2+: turn on in automatic mode
+		Fan speed control method:
+		0: no fan speed control (i.e. fan at full speed)
+		1: manual fan speed control enabled (using pwm[1-*])
+		2+: automatic fan speed control enabled
 		Check individual chip documentation files for automatic mode
 		details.
 		RW
@@ -343,9 +342,9 @@
 supports it. When this boolean has value 1, the measurement for that
 channel should not be trusted.
 
-in[0-*]_input_fault
-fan[1-*]_input_fault
-temp[1-*]_input_fault
+in[0-*]_fault
+fan[1-*]_fault
+temp[1-*]_fault
 		Input fault condition
 		0: no fault occured
 		1: fault condition
diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf
index 030fac6..ccc2bcb 100644
--- a/Documentation/hwmon/w83627ehf
+++ b/Documentation/hwmon/w83627ehf
@@ -22,9 +22,9 @@
 W83627DHG super I/O chips. We will refer to them collectively as Winbond chips.
 
 The chips implement three temperature sensors, five fan rotation
-speed sensors, ten analog voltage sensors (only nine for the 627DHG), alarms
-with beep warnings (control unimplemented), and some automatic fan regulation
-strategies (plus manual fan control mode).
+speed sensors, ten analog voltage sensors (only nine for the 627DHG), one
+VID (6 pins), alarms with beep warnings (control unimplemented), and
+some automatic fan regulation strategies (plus manual fan control mode).
 
 Temperatures are measured in degrees Celsius and measurement resolution is 1
 degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
diff --git a/MAINTAINERS b/MAINTAINERS
index 0c83823f..fbe0dca 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -607,6 +607,12 @@
 W:	http://xf.iksaif.net/acpi4asus
 S:	Maintained
 
+ASUS ASB100 HARDWARE MONITOR DRIVER
+P:	Mark M. Hoffman
+M:	mhoffman@lightlink.com
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+
 ASUS LAPTOP EXTRAS DRIVER
 P:	Corentin Chary
 M:	corentincj@iksaif.net
@@ -1273,6 +1279,12 @@
 L:	linux-kernel@vger.kernel.org
 S:	Maintained
 
+DME1737 HARDWARE MONITOR DRIVER
+P:	Juerg Haefliger
+M:	juergh@gmail.com
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+
 DOCBOOK FOR DOCUMENTATION
 P:	Randy Dunlap
 M:	rdunlap@xenotime.net
@@ -1623,11 +1635,11 @@
 S:	Maintained
 
 HARDWARE MONITORING
-P:	Jean Delvare
-M:	khali@linux-fr.org
+P:	Mark M. Hoffman
+M:	mhoffman@lightlink.com
 L:	lm-sensors@lm-sensors.org
 W:	http://www.lm-sensors.org/
-T:	quilt http://khali.linux-fr.org/devel/linux-2.6/jdelvare-hwmon/
+T:	git lm-sensors.org:/kernel/mhoffman/hwmon-2.6.git
 S:	Maintained
 
 HARDWARE RANDOM NUMBER GENERATOR CORE
@@ -1763,6 +1775,12 @@
 M:	wli@holomorphy.com
 S:	Maintained
 
+I2C/SMBUS STUB DRIVER
+P:	Mark M. Hoffman
+M:	mhoffman@lightlink.com
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+
 I2C SUBSYSTEM
 P:	Jean Delvare
 M:	khali@linux-fr.org
@@ -3292,6 +3310,12 @@
 L:	netdev@vger.kernel.org
 S:	Maintained
 
+SIS 96X I2C/SMBUS DRIVER
+P:	Mark M. Hoffman
+M:	mhoffman@lightlink.com
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+
 SIS FRAMEBUFFER DRIVER
 P:	Thomas Winischhofer
 M:	thomas@winischhofer.net
@@ -3309,6 +3333,12 @@
 M:	nico@cam.org
 S:	Maintained
 
+SMSC47B397 HARDWARE MONITOR DRIVER
+P:	Mark M. Hoffman
+M:	mhoffman@lightlink.com
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+
 SOFTMAC LAYER (IEEE 802.11)
 P:	Johannes Berg
 M:	johannes@sipsolutions.net
diff --git a/arch/arm/configs/badge4_defconfig b/arch/arm/configs/badge4_defconfig
index 821865f..b2bbf21 100644
--- a/arch/arm/configs/badge4_defconfig
+++ b/arch/arm/configs/badge4_defconfig
@@ -708,7 +708,6 @@
 # I2C Hardware Bus support
 #
 CONFIG_I2C_ELEKTOR=m
-# CONFIG_I2C_ISA is not set
 # CONFIG_I2C_PARPORT is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
 # CONFIG_I2C_STUB is not set
diff --git a/arch/arm/configs/clps7500_defconfig b/arch/arm/configs/clps7500_defconfig
index af9ae538..49e9f9d 100644
--- a/arch/arm/configs/clps7500_defconfig
+++ b/arch/arm/configs/clps7500_defconfig
@@ -536,7 +536,6 @@
 # I2C Hardware Bus support
 #
 # CONFIG_I2C_ELEKTOR is not set
-# CONFIG_I2C_ISA is not set
 # CONFIG_I2C_PARPORT is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
 # CONFIG_I2C_PCA_ISA is not set
diff --git a/arch/arm/configs/footbridge_defconfig b/arch/arm/configs/footbridge_defconfig
index 2a612d2..299dc22 100644
--- a/arch/arm/configs/footbridge_defconfig
+++ b/arch/arm/configs/footbridge_defconfig
@@ -748,7 +748,6 @@
 # CONFIG_I2C_ELEKTOR is not set
 # CONFIG_I2C_I801 is not set
 # CONFIG_I2C_I810 is not set
-# CONFIG_I2C_ISA is not set
 # CONFIG_I2C_NFORCE2 is not set
 # CONFIG_I2C_PARPORT is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
diff --git a/arch/arm/configs/neponset_defconfig b/arch/arm/configs/neponset_defconfig
index e86794a..92ccdc6 100644
--- a/arch/arm/configs/neponset_defconfig
+++ b/arch/arm/configs/neponset_defconfig
@@ -698,7 +698,6 @@
 # I2C Hardware Bus support
 #
 # CONFIG_I2C_ELEKTOR is not set
-# CONFIG_I2C_ISA is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
 # CONFIG_I2C_STUB is not set
 # CONFIG_I2C_PCA_ISA is not set
diff --git a/arch/arm/configs/picotux200_defconfig b/arch/arm/configs/picotux200_defconfig
index 339c489..3c0c4f1 100644
--- a/arch/arm/configs/picotux200_defconfig
+++ b/arch/arm/configs/picotux200_defconfig
@@ -735,7 +735,6 @@
 # I2C Hardware Bus support
 #
 CONFIG_I2C_AT91=m
-CONFIG_I2C_ISA=m
 # CONFIG_I2C_OCORES is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
 # CONFIG_I2C_STUB is not set
diff --git a/arch/arm/configs/rpc_defconfig b/arch/arm/configs/rpc_defconfig
index bc09126..8452dc8 100644
--- a/arch/arm/configs/rpc_defconfig
+++ b/arch/arm/configs/rpc_defconfig
@@ -558,7 +558,6 @@
 #
 # I2C Hardware Bus support
 #
-# CONFIG_I2C_ISA is not set
 # CONFIG_I2C_PARPORT is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
 # CONFIG_I2C_STUB is not set
diff --git a/arch/arm/configs/s3c2410_defconfig b/arch/arm/configs/s3c2410_defconfig
index a850da3..1d5150e 100644
--- a/arch/arm/configs/s3c2410_defconfig
+++ b/arch/arm/configs/s3c2410_defconfig
@@ -826,7 +826,6 @@
 # I2C Hardware Bus support
 #
 # CONFIG_I2C_ELEKTOR is not set
-CONFIG_I2C_ISA=m
 # CONFIG_I2C_OCORES is not set
 # CONFIG_I2C_PARPORT is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
diff --git a/arch/m32r/m32104ut/defconfig.m32104ut b/arch/m32r/m32104ut/defconfig.m32104ut
index 7b68fe8..1f88f49 100644
--- a/arch/m32r/m32104ut/defconfig.m32104ut
+++ b/arch/m32r/m32104ut/defconfig.m32104ut
@@ -699,7 +699,6 @@
 # I2C Hardware Bus support
 #
 CONFIG_I2C_ELEKTOR=m
-CONFIG_I2C_ISA=m
 # CONFIG_I2C_OCORES is not set
 # CONFIG_I2C_PARPORT is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
diff --git a/arch/ppc/configs/ev64260_defconfig b/arch/ppc/configs/ev64260_defconfig
index 84cc142..587e9a3 100644
--- a/arch/ppc/configs/ev64260_defconfig
+++ b/arch/ppc/configs/ev64260_defconfig
@@ -531,7 +531,6 @@
 # CONFIG_I2C_AMD8111 is not set
 # CONFIG_I2C_I801 is not set
 # CONFIG_I2C_I810 is not set
-# CONFIG_I2C_ISA is not set
 # CONFIG_I2C_NFORCE2 is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
 # CONFIG_I2C_PIIX4 is not set
diff --git a/arch/ppc/configs/mpc8540_ads_defconfig b/arch/ppc/configs/mpc8540_ads_defconfig
index c5c8602..bf676eb 100644
--- a/arch/ppc/configs/mpc8540_ads_defconfig
+++ b/arch/ppc/configs/mpc8540_ads_defconfig
@@ -452,7 +452,6 @@
 # CONFIG_I2C_AMD8111 is not set
 # CONFIG_I2C_I801 is not set
 # CONFIG_I2C_I810 is not set
-# CONFIG_I2C_ISA is not set
 CONFIG_I2C_MPC=y
 # CONFIG_I2C_NFORCE2 is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
diff --git a/arch/ppc/configs/mpc8548_cds_defconfig b/arch/ppc/configs/mpc8548_cds_defconfig
index abe034f..f36fc5db 100644
--- a/arch/ppc/configs/mpc8548_cds_defconfig
+++ b/arch/ppc/configs/mpc8548_cds_defconfig
@@ -413,7 +413,6 @@
 #
 # I2C Hardware Bus support
 #
-# CONFIG_I2C_ISA is not set
 CONFIG_I2C_MPC=y
 # CONFIG_I2C_PARPORT_LIGHT is not set
 # CONFIG_I2C_PCA_ISA is not set
diff --git a/arch/ppc/configs/mpc8555_cds_defconfig b/arch/ppc/configs/mpc8555_cds_defconfig
index 15abebf..4f1e320 100644
--- a/arch/ppc/configs/mpc8555_cds_defconfig
+++ b/arch/ppc/configs/mpc8555_cds_defconfig
@@ -518,7 +518,6 @@
 # CONFIG_I2C_I801 is not set
 # CONFIG_I2C_I810 is not set
 # CONFIG_I2C_PIIX4 is not set
-# CONFIG_I2C_ISA is not set
 CONFIG_I2C_MPC=y
 # CONFIG_I2C_NFORCE2 is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
diff --git a/arch/ppc/configs/mpc8560_ads_defconfig b/arch/ppc/configs/mpc8560_ads_defconfig
index f834fb5..f12d48f 100644
--- a/arch/ppc/configs/mpc8560_ads_defconfig
+++ b/arch/ppc/configs/mpc8560_ads_defconfig
@@ -489,7 +489,6 @@
 # CONFIG_I2C_I801 is not set
 # CONFIG_I2C_I810 is not set
 # CONFIG_I2C_PIIX4 is not set
-# CONFIG_I2C_ISA is not set
 CONFIG_I2C_MPC=y
 # CONFIG_I2C_NFORCE2 is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
diff --git a/arch/ppc/configs/radstone_ppc7d_defconfig b/arch/ppc/configs/radstone_ppc7d_defconfig
index ca4d1fd..9f64532 100644
--- a/arch/ppc/configs/radstone_ppc7d_defconfig
+++ b/arch/ppc/configs/radstone_ppc7d_defconfig
@@ -710,7 +710,6 @@
 # CONFIG_I2C_I801 is not set
 # CONFIG_I2C_I810 is not set
 # CONFIG_I2C_PIIX4 is not set
-# CONFIG_I2C_ISA is not set
 # CONFIG_I2C_MPC is not set
 # CONFIG_I2C_NFORCE2 is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
diff --git a/arch/ppc/configs/stx_gp3_defconfig b/arch/ppc/configs/stx_gp3_defconfig
index 3fedc43..70d6f84 100644
--- a/arch/ppc/configs/stx_gp3_defconfig
+++ b/arch/ppc/configs/stx_gp3_defconfig
@@ -661,7 +661,6 @@
 # CONFIG_I2C_I801 is not set
 # CONFIG_I2C_I810 is not set
 # CONFIG_I2C_PIIX4 is not set
-# CONFIG_I2C_ISA is not set
 # CONFIG_I2C_MPC is not set
 # CONFIG_I2C_NFORCE2 is not set
 # CONFIG_I2C_PARPORT is not set
diff --git a/arch/ppc/configs/sycamore_defconfig b/arch/ppc/configs/sycamore_defconfig
index 758114c..6996cca 100644
--- a/arch/ppc/configs/sycamore_defconfig
+++ b/arch/ppc/configs/sycamore_defconfig
@@ -461,7 +461,6 @@
 # CONFIG_I2C_I801 is not set
 # CONFIG_I2C_I810 is not set
 # CONFIG_I2C_IBM_IIC is not set
-# CONFIG_I2C_ISA is not set
 # CONFIG_I2C_NFORCE2 is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
 # CONFIG_I2C_PIIX4 is not set
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 13eea47..dbdca6f 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -29,17 +29,34 @@
 	default n
 
 config SENSORS_ABITUGURU
-	tristate "Abit uGuru"
+	tristate "Abit uGuru (rev 1 & 2)"
 	depends on EXPERIMENTAL
 	help
-	  If you say yes here you get support for the Abit uGuru chips
-	  sensor part. The voltage and frequency control parts of the Abit
-	  uGuru are not supported. The Abit uGuru chip can be found on Abit
-	  uGuru featuring motherboards (most modern Abit motherboards).
+	  If you say yes here you get support for the sensor part of the first
+	  and second revision of the Abit uGuru chip. The voltage and frequency
+	  control parts of the Abit uGuru are not supported. The Abit uGuru
+	  chip can be found on Abit uGuru featuring motherboards (most modern
+	  Abit motherboards from before end 2005). For more info and a list
+	  of which motherboards have which revision see
+	  Documentation/hwmon/abituguru
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called abituguru.
 
+config SENSORS_ABITUGURU3
+	tristate "Abit uGuru (rev 3)"
+	depends on HWMON && EXPERIMENTAL
+	help
+	  If you say yes here you get support for the sensor part of the
+	  third revision of the Abit uGuru chip. Only reading the sensors
+	  and their settings is supported. The third revision of the Abit
+	  uGuru chip can be found on recent Abit motherboards (since end
+	  2005). For more info and a list of which motherboards have which
+	  revision see Documentation/hwmon/abituguru3
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called abituguru3.
+
 config SENSORS_AD7418
 	tristate "Analog Devices AD7416, AD7417 and AD7418"
 	depends on I2C && EXPERIMENTAL
@@ -250,12 +267,10 @@
 
 config SENSORS_IT87
 	tristate "ITE IT87xx and compatibles"
-	depends on I2C
-	select I2C_ISA
 	select HWMON_VID
 	help
 	  If you say yes here you get support for ITE IT8705F, IT8712F,
-	  IT8716F and IT8718F sensor chips, and the SiS960 clone.
+	  IT8716F, IT8718F and IT8726F sensor chips, and the SiS960 clone.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called it87.
@@ -365,8 +380,8 @@
 	depends on I2C
 	help
 	  If you say yes here you get support for National Semiconductor LM90,
-	  LM86, LM89 and LM99, Analog Devices ADM1032 and Maxim MAX6657 and
-	  MAX6658 sensor chips.
+	  LM86, LM89 and LM99, Analog Devices ADM1032 and Maxim MAX6657,
+	  MAX6658, MAX6659, MAX6680 and MAX6681 sensor chips.
 
 	  The Analog Devices ADT7461 sensor chip is also supported, but only
 	  if found in ADM1032 compatibility mode.
@@ -384,6 +399,17 @@
 	  This driver can also be built as a module.  If so, the module
 	  will be called lm92.
 
+config SENSORS_LM93
+	tristate "National Semiconductor LM93 and compatibles"
+	depends on HWMON && I2C
+	select HWMON_VID
+	help
+	  If you say yes here you get support for National Semiconductor LM93
+	  sensor chips.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called lm93.
+
 config SENSORS_MAX1619
 	tristate "Maxim MAX1619 sensor chip"
 	depends on I2C
@@ -405,8 +431,6 @@
 
 config SENSORS_PC87360
 	tristate "National Semiconductor PC87360 family"
-	depends on I2C && EXPERIMENTAL
-	select I2C_ISA
 	select HWMON_VID
 	help
 	  If you say yes here you get access to the hardware monitoring
@@ -433,8 +457,7 @@
 
 config SENSORS_SIS5595
 	tristate "Silicon Integrated Systems Corp. SiS5595"
-	depends on I2C && PCI && EXPERIMENTAL
-	select I2C_ISA
+	depends on PCI
 	help
 	  If you say yes here you get support for the integrated sensors in
 	  SiS5595 South Bridges.
@@ -442,6 +465,18 @@
 	  This driver can also be built as a module.  If so, the module
 	  will be called sis5595.
 
+config SENSORS_DME1737
+	tristate "SMSC DME1737 and compatibles"
+	depends on I2C && EXPERIMENTAL
+	select HWMON_VID
+	help
+	  If you say yes here you get support for the hardware monitoring
+	  and fan control features of the SMSC DME1737 (and compatibles
+	  like the Asus A8000) Super-I/O chip.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called dme1737.
+
 config SENSORS_SMSC47M1
 	tristate "SMSC LPC47M10x and compatibles"
 	help
@@ -487,8 +522,7 @@
 
 config SENSORS_VIA686A
 	tristate "VIA686A"
-	depends on I2C && PCI
-	select I2C_ISA
+	depends on PCI
 	help
 	  If you say yes here you get support for the integrated sensors in
 	  Via 686A/B South Bridges.
@@ -509,9 +543,8 @@
 
 config SENSORS_VT8231
 	tristate "VIA VT8231"
-	depends on I2C && PCI && EXPERIMENTAL
+	depends on PCI
 	select HWMON_VID
-	select I2C_ISA
 	help
 	  If you say yes here then you get support for the integrated sensors
 	  in the VIA VT8231 device.
@@ -584,17 +617,16 @@
 	  will be called w83627hf.
 
 config SENSORS_W83627EHF
-	tristate "Winbond W83627EHF"
-	depends on I2C && EXPERIMENTAL
-	select I2C_ISA
+	tristate "Winbond W83627EHF/DHG"
+	select HWMON_VID
 	help
-	  If you say yes here you get preliminary support for the hardware
+	  If you say yes here you get support for the hardware
 	  monitoring functionality of the Winbond W83627EHF Super-I/O chip.
-	  Only fan and temperature inputs are supported at the moment, while
-	  the chip does much more than that.
 
 	  This driver also supports the W83627EHG, which is the lead-free
-	  version of the W83627EHF.
+	  version of the W83627EHF, and the W83627DHG, which is a similar
+	  chip suited for specific Intel processors that use PECI such as
+	  the Core 2 Duo.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called w83627ehf.
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index cfaf338..59f81fa 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -14,6 +14,7 @@
 obj-$(CONFIG_SENSORS_W83791D)	+= w83791d.o
 
 obj-$(CONFIG_SENSORS_ABITUGURU)	+= abituguru.o
+obj-$(CONFIG_SENSORS_ABITUGURU3)+= abituguru3.o
 obj-$(CONFIG_SENSORS_AD7418)	+= ad7418.o
 obj-$(CONFIG_SENSORS_ADM1021)	+= adm1021.o
 obj-$(CONFIG_SENSORS_ADM1025)	+= adm1025.o
@@ -25,6 +26,7 @@
 obj-$(CONFIG_SENSORS_AMS)	+= ams/
 obj-$(CONFIG_SENSORS_ATXP1)	+= atxp1.o
 obj-$(CONFIG_SENSORS_CORETEMP)	+= coretemp.o
+obj-$(CONFIG_SENSORS_DME1737)	+= dme1737.o
 obj-$(CONFIG_SENSORS_DS1621)	+= ds1621.o
 obj-$(CONFIG_SENSORS_F71805F)	+= f71805f.o
 obj-$(CONFIG_SENSORS_FSCHER)	+= fscher.o
@@ -45,6 +47,7 @@
 obj-$(CONFIG_SENSORS_LM87)	+= lm87.o
 obj-$(CONFIG_SENSORS_LM90)	+= lm90.o
 obj-$(CONFIG_SENSORS_LM92)	+= lm92.o
+obj-$(CONFIG_SENSORS_LM93)	+= lm93.o
 obj-$(CONFIG_SENSORS_MAX1619)	+= max1619.o
 obj-$(CONFIG_SENSORS_MAX6650)	+= max6650.o
 obj-$(CONFIG_SENSORS_PC87360)	+= pc87360.o
diff --git a/drivers/hwmon/abituguru.c b/drivers/hwmon/abituguru.c
index bede4d9..d575ee9 100644
--- a/drivers/hwmon/abituguru.c
+++ b/drivers/hwmon/abituguru.c
@@ -16,9 +16,9 @@
     Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */
 /*
-    This driver supports the sensor part of the custom Abit uGuru chip found
-    on Abit uGuru motherboards. Note: because of lack of specs the CPU / RAM /
-    etc voltage & frequency control is not supported!
+    This driver supports the sensor part of the first and second revision of
+    the custom Abit uGuru chip found on Abit uGuru motherboards. Note: because
+    of lack of specs the CPU/RAM voltage & frequency control is not supported!
 */
 #include <linux/module.h>
 #include <linux/sched.h>
@@ -31,6 +31,7 @@
 #include <linux/platform_device.h>
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
+#include <linux/dmi.h>
 #include <asm/io.h>
 
 /* Banks */
@@ -418,7 +419,7 @@
 abituguru_detect_bank1_sensor_type(struct abituguru_data *data,
 				   u8 sensor_addr)
 {
-	u8 val, buf[3];
+	u8 val, test_flag, buf[3];
 	int i, ret = -ENODEV; /* error is the most common used retval :| */
 
 	/* If overriden by the user return the user selected type */
@@ -436,7 +437,7 @@
 		return -ENODEV;
 
 	/* Test val is sane / usable for sensor type detection. */
-	if ((val < 10u) || (val > 240u)) {
+	if ((val < 10u) || (val > 250u)) {
 		printk(KERN_WARNING ABIT_UGURU_NAME
 			": bank1-sensor: %d reading (%d) too close to limits, "
 			"unable to determine sensor type, skipping sensor\n",
@@ -449,10 +450,20 @@
 
 	ABIT_UGURU_DEBUG(2, "testing bank1 sensor %d\n", (int)sensor_addr);
 	/* Volt sensor test, enable volt low alarm, set min value ridicously
-	   high. If its a volt sensor this should always give us an alarm. */
-	buf[0] = ABIT_UGURU_VOLT_LOW_ALARM_ENABLE;
-	buf[1] = 245;
-	buf[2] = 250;
+	   high, or vica versa if the reading is very high. If its a volt
+	   sensor this should always give us an alarm. */
+	if (val <= 240u) {
+		buf[0] = ABIT_UGURU_VOLT_LOW_ALARM_ENABLE;
+		buf[1] = 245;
+		buf[2] = 250;
+		test_flag = ABIT_UGURU_VOLT_LOW_ALARM_FLAG;
+	} else {
+		buf[0] = ABIT_UGURU_VOLT_HIGH_ALARM_ENABLE;
+		buf[1] = 5;
+		buf[2] = 10;
+		test_flag = ABIT_UGURU_VOLT_HIGH_ALARM_FLAG;
+	}
+
 	if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
 			buf, 3) != 3)
 		goto abituguru_detect_bank1_sensor_type_exit;
@@ -469,13 +480,13 @@
 				sensor_addr, buf, 3,
 				ABIT_UGURU_MAX_RETRIES) != 3)
 			goto abituguru_detect_bank1_sensor_type_exit;
-		if (buf[0] & ABIT_UGURU_VOLT_LOW_ALARM_FLAG) {
+		if (buf[0] & test_flag) {
 			ABIT_UGURU_DEBUG(2, "  found volt sensor\n");
 			ret = ABIT_UGURU_IN_SENSOR;
 			goto abituguru_detect_bank1_sensor_type_exit;
 		} else
 			ABIT_UGURU_DEBUG(2, "  alarm raised during volt "
-				"sensor test, but volt low flag not set\n");
+				"sensor test, but volt range flag not set\n");
 	} else
 		ABIT_UGURU_DEBUG(2, "  alarm not raised during volt sensor "
 			"test\n");
@@ -1287,6 +1298,7 @@
 	for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++)
 		device_remove_file(&pdev->dev,
 			&abituguru_sysfs_attr[i].dev_attr);
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 	return res;
 }
@@ -1296,13 +1308,13 @@
 	int i;
 	struct abituguru_data *data = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
 	hwmon_device_unregister(data->class_dev);
 	for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++)
 		device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
 	for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++)
 		device_remove_file(&pdev->dev,
 			&abituguru_sysfs_attr[i].dev_attr);
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 
 	return 0;
@@ -1436,6 +1448,15 @@
 	int address, err;
 	struct resource res = { .flags = IORESOURCE_IO };
 
+#ifdef CONFIG_DMI
+	char *board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR);
+
+	/* safety check, refuse to load on non Abit motherboards */
+	if (!force && (!board_vendor ||
+			strcmp(board_vendor, "http://www.abit.com.tw/")))
+		return -ENODEV;
+#endif
+
 	address = abituguru_detect();
 	if (address < 0)
 		return address;
diff --git a/drivers/hwmon/abituguru3.c b/drivers/hwmon/abituguru3.c
new file mode 100644
index 0000000..a003d10
--- /dev/null
+++ b/drivers/hwmon/abituguru3.c
@@ -0,0 +1,1140 @@
+/*
+    abituguru3.c Copyright (c) 2006 Hans de Goede <j.w.r.degoede@hhs.nl>
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation; either version 2 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program; if not, write to the Free Software
+    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+/*
+    This driver supports the sensor part of revision 3 of the custom Abit uGuru
+    chip found on newer Abit uGuru motherboards. Note: because of lack of specs
+    only reading the sensors and their settings is supported.
+*/
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/mutex.h>
+#include <linux/err.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <asm/io.h>
+
+/* uGuru3 bank addresses */
+#define ABIT_UGURU3_SETTINGS_BANK		0x01
+#define ABIT_UGURU3_SENSORS_BANK		0x08
+#define ABIT_UGURU3_MISC_BANK			0x09
+#define ABIT_UGURU3_ALARMS_START		0x1E
+#define ABIT_UGURU3_SETTINGS_START		0x24
+#define ABIT_UGURU3_VALUES_START		0x80
+#define ABIT_UGURU3_BOARD_ID			0x0A
+/* uGuru3 sensor bank flags */			     /* Alarm if: */
+#define ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE	0x01 /*  temp over warn */
+#define ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE	0x02 /*  volt over max */
+#define ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE	0x04 /*  volt under min */
+#define ABIT_UGURU3_TEMP_HIGH_ALARM_FLAG	0x10 /* temp is over warn */
+#define ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG	0x20 /* volt is over max */
+#define ABIT_UGURU3_VOLT_LOW_ALARM_FLAG		0x40 /* volt is under min */
+#define ABIT_UGURU3_FAN_LOW_ALARM_ENABLE	0x01 /*   fan under min */
+#define ABIT_UGURU3_BEEP_ENABLE			0x08 /* beep if alarm */
+#define ABIT_UGURU3_SHUTDOWN_ENABLE		0x80 /* shutdown if alarm */
+/* sensor types */
+#define ABIT_UGURU3_IN_SENSOR			0
+#define ABIT_UGURU3_TEMP_SENSOR			1
+#define ABIT_UGURU3_FAN_SENSOR			2
+
+/* Timeouts / Retries, if these turn out to need a lot of fiddling we could
+   convert them to params. Determined by trial and error. I assume this is
+   cpu-speed independent, since the ISA-bus and not the CPU should be the
+   bottleneck. */
+#define ABIT_UGURU3_WAIT_TIMEOUT		250
+/* Normally the 0xAC at the end of synchronize() is reported after the
+   first read, but sometimes not and we need to poll */
+#define ABIT_UGURU3_SYNCHRONIZE_TIMEOUT		5
+/* utility macros */
+#define ABIT_UGURU3_NAME			"abituguru3"
+#define ABIT_UGURU3_DEBUG(format, arg...)	\
+	if (verbose)				\
+		printk(KERN_DEBUG ABIT_UGURU3_NAME ": "	format , ## arg)
+
+/* Macros to help calculate the sysfs_names array length */
+#define ABIT_UGURU3_MAX_NO_SENSORS 26
+/* sum of strlen +1 of: in??_input\0, in??_{min,max}\0, in??_{min,max}_alarm\0,
+   in??_{min,max}_alarm_enable\0, in??_beep\0, in??_shutdown\0, in??_label\0 */
+#define ABIT_UGURU3_IN_NAMES_LENGTH (11 + 2 * 9 + 2 * 15 + 2 * 22 + 10 + 14 + 11)
+/* sum of strlen +1 of: temp??_input\0, temp??_max\0, temp??_crit\0,
+   temp??_alarm\0, temp??_alarm_enable\0, temp??_beep\0, temp??_shutdown\0,
+   temp??_label\0 */
+#define ABIT_UGURU3_TEMP_NAMES_LENGTH (13 + 11 + 12 + 13 + 20 + 12 + 16 + 13)
+/* sum of strlen +1 of: fan??_input\0, fan??_min\0, fan??_alarm\0,
+   fan??_alarm_enable\0, fan??_beep\0, fan??_shutdown\0, fan??_label\0 */
+#define ABIT_UGURU3_FAN_NAMES_LENGTH (12 + 10 + 12 + 19 + 11 + 15 + 12)
+/* Worst case scenario 16 in sensors (longest names_length) and the rest
+   temp sensors (second longest names_length). */
+#define ABIT_UGURU3_SYSFS_NAMES_LENGTH (16 * ABIT_UGURU3_IN_NAMES_LENGTH + \
+	(ABIT_UGURU3_MAX_NO_SENSORS - 16) * ABIT_UGURU3_TEMP_NAMES_LENGTH)
+
+/* All the macros below are named identical to the openguru2 program
+   reverse engineered by Louis Kruger, hence the names might not be 100%
+   logical. I could come up with better names, but I prefer keeping the names
+   identical so that this driver can be compared with his work more easily. */
+/* Two i/o-ports are used by uGuru */
+#define ABIT_UGURU3_BASE			0x00E0
+#define ABIT_UGURU3_CMD				0x00
+#define ABIT_UGURU3_DATA			0x04
+#define ABIT_UGURU3_REGION_LENGTH		5
+/* The wait_xxx functions return this on success and the last contents
+   of the DATA register (0-255) on failure. */
+#define ABIT_UGURU3_SUCCESS			-1
+/* uGuru status flags */
+#define ABIT_UGURU3_STATUS_READY_FOR_READ	0x01
+#define ABIT_UGURU3_STATUS_BUSY			0x02
+
+
+/* Structures */
+struct abituguru3_sensor_info {
+	const char* name;
+	int port;
+	int type;
+	int multiplier;
+	int divisor;
+	int offset;
+};
+
+struct abituguru3_motherboard_info {
+	u16 id;
+	const char *name;
+	/* + 1 -> end of sensors indicated by a sensor with name == NULL */
+	struct abituguru3_sensor_info sensors[ABIT_UGURU3_MAX_NO_SENSORS + 1];
+};
+
+/* For the Abit uGuru, we need to keep some data in memory.
+   The structure is dynamically allocated, at the same time when a new
+   abituguru3 device is allocated. */
+struct abituguru3_data {
+	struct class_device *class_dev; /* hwmon registered device */
+	struct mutex update_lock;	/* protect access to data and uGuru */
+	unsigned short addr;		/* uguru base address */
+	char valid;			/* !=0 if following fields are valid */
+	unsigned long last_updated;	/* In jiffies */
+
+	/* For convenience the sysfs attr and their names are generated
+	   automatically. We have max 10 entries per sensor (for in sensors) */
+	struct sensor_device_attribute_2 sysfs_attr[ABIT_UGURU3_MAX_NO_SENSORS
+		* 10];
+
+	/* Buffer to store the dynamically generated sysfs names */
+	char sysfs_names[ABIT_UGURU3_SYSFS_NAMES_LENGTH];
+
+	/* Pointer to the sensors info for the detected motherboard */
+	const struct abituguru3_sensor_info *sensors;
+
+	/* The abituguru3 supports upto 48 sensors, and thus has registers
+	   sets for 48 sensors, for convienence reasons / simplicity of the
+	   code we always read and store all registers for all 48 sensors */
+
+	/* Alarms for all 48 sensors (1 bit per sensor) */
+	u8 alarms[48/8];
+
+	/* Value of all 48 sensors */
+	u8 value[48];
+
+	/* Settings of all 48 sensors, note in and temp sensors (the first 32
+	   sensors) have 3 bytes of settings, while fans only have 2 bytes,
+	   for convenience we use 3 bytes for all sensors */
+	u8 settings[48][3];
+};
+
+
+/* Constants */
+static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
+	{ 0x000C, "unknown", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR",		 1, 0, 10, 1, 0 },
+		{ "DDR VTT",		 2, 0, 10, 1, 0 },
+		{ "CPU VTT 1.2V",	 3, 0, 10, 1, 0 },
+		{ "MCH & PCIE 1.5V",	 4, 0, 10, 1, 0 },
+		{ "MCH 2.5V",		 5, 0, 20, 1, 0 },
+		{ "ICH 1.05V",		 6, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "System ",		25, 1, 1, 1, 0 },
+		{ "PWM",		26, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "NB Fan",		33, 2, 60, 1, 0 },
+		{ "SYS FAN",		34, 2, 60, 1, 0 },
+		{ "AUX1 Fan",		35, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x000D, "Abit AW8", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR",		 1, 0, 10, 1, 0 },
+		{ "DDR VTT",		 2, 0, 10, 1, 0 },
+		{ "CPU VTT 1.2V",	 3, 0, 10, 1, 0 },
+		{ "MCH & PCIE 1.5V",	 4, 0, 10, 1, 0 },
+		{ "MCH 2.5V",		 5, 0, 20, 1, 0 },
+		{ "ICH 1.05V",		 6, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "System ",		25, 1, 1, 1, 0 },
+		{ "PWM1",		26, 1, 1, 1, 0 },
+		{ "PWM2",		27, 1, 1, 1, 0 },
+		{ "PWM3",		28, 1, 1, 1, 0 },
+		{ "PWM4",		29, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "NB Fan",		33, 2, 60, 1, 0 },
+		{ "SYS Fan",		34, 2, 60, 1, 0 },
+		{ "AUX1 Fan",		35, 2, 60, 1, 0 },
+		{ "AUX2 Fan",		36, 2, 60, 1, 0 },
+		{ "AUX3 Fan",		37, 2, 60, 1, 0 },
+		{ "AUX4 Fan",		38, 2, 60, 1, 0 },
+		{ "AUX5 Fan",		39, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x000E, "AL-8", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR",		 1, 0, 10, 1, 0 },
+		{ "DDR VTT",		 2, 0, 10, 1, 0 },
+		{ "CPU VTT 1.2V",	 3, 0, 10, 1, 0 },
+		{ "MCH & PCIE 1.5V",	 4, 0, 10, 1, 0 },
+		{ "MCH 2.5V",		 5, 0, 20, 1, 0 },
+		{ "ICH 1.05V",		 6, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "System ",		25, 1, 1, 1, 0 },
+		{ "PWM",		26, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "NB Fan",		33, 2, 60, 1, 0 },
+		{ "SYS Fan",		34, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x000F, "unknown", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR",		 1, 0, 10, 1, 0 },
+		{ "DDR VTT",		 2, 0, 10, 1, 0 },
+		{ "CPU VTT 1.2V",	 3, 0, 10, 1, 0 },
+		{ "MCH & PCIE 1.5V",	 4, 0, 10, 1, 0 },
+		{ "MCH 2.5V",		 5, 0, 20, 1, 0 },
+		{ "ICH 1.05V",		 6, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "System ",		25, 1, 1, 1, 0 },
+		{ "PWM",		26, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "NB Fan",		33, 2, 60, 1, 0 },
+		{ "SYS Fan",		34, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x0010, "Abit NI8 SLI GR", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR",		 1, 0, 10, 1, 0 },
+		{ "DDR VTT",		 2, 0, 10, 1, 0 },
+		{ "CPU VTT 1.2V",	 3, 0, 10, 1, 0 },
+		{ "NB 1.4V",		 4, 0, 10, 1, 0 },
+		{ "SB 1.5V",		 6, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "SYS",		25, 1, 1, 1, 0 },
+		{ "PWM",		26, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "NB Fan",		33, 2, 60, 1, 0 },
+		{ "SYS Fan",		34, 2, 60, 1, 0 },
+		{ "AUX1 Fan",		35, 2, 60, 1, 0 },
+		{ "OTES1 Fan",		36, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x0011, "Abit AT8 32X", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR",		 1, 0, 20, 1, 0 },
+		{ "DDR VTT",		 2, 0, 10, 1, 0 },
+		{ "CPU VDDA 2.5V",	 6, 0, 20, 1, 0 },
+		{ "NB 1.8V",		 4, 0, 10, 1, 0 },
+		{ "NB 1.8V Dual",	 5, 0, 10, 1, 0 },
+		{ "HTV 1.2",		 3, 0, 10, 1, 0 },
+		{ "PCIE 1.2V",		12, 0, 10, 1, 0 },
+		{ "NB 1.2V",		13, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "NB",			25, 1, 1, 1, 0 },
+		{ "System",		26, 1, 1, 1, 0 },
+		{ "PWM",		27, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "NB Fan",		33, 2, 60, 1, 0 },
+		{ "SYS Fan",		34, 2, 60, 1, 0 },
+		{ "AUX1 Fan",		35, 2, 60, 1, 0 },
+		{ "AUX2 Fan",		36, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x0012, "Abit AN8 32X", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR",		 1, 0, 20, 1, 0 },
+		{ "DDR VTT",		 2, 0, 10, 1, 0 },
+		{ "HyperTransport",	 3, 0, 10, 1, 0 },
+		{ "CPU VDDA 2.5V",	 5, 0, 20, 1, 0 },
+		{ "NB",			 4, 0, 10, 1, 0 },
+		{ "SB",			 6, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "SYS",		25, 1, 1, 1, 0 },
+		{ "PWM",		26, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "NB Fan",		33, 2, 60, 1, 0 },
+		{ "SYS Fan",		34, 2, 60, 1, 0 },
+		{ "AUX1 Fan",		36, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x0013, "unknown", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR",		 1, 0, 10, 1, 0 },
+		{ "DDR VTT",		 2, 0, 10, 1, 0 },
+		{ "CPU VTT 1.2V",	 3, 0, 10, 1, 0 },
+		{ "MCH & PCIE 1.5V",	 4, 0, 10, 1, 0 },
+		{ "MCH 2.5V",		 5, 0, 20, 1, 0 },
+		{ "ICH 1.05V",		 6, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "System ",		25, 1, 1, 1, 0 },
+		{ "PWM1",		26, 1, 1, 1, 0 },
+		{ "PWM2",		27, 1, 1, 1, 0 },
+		{ "PWM3",		28, 1, 1, 1, 0 },
+		{ "PWM4",		29, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "NB Fan",		33, 2, 60, 1, 0 },
+		{ "SYS Fan",		34, 2, 60, 1, 0 },
+		{ "AUX1 Fan",		35, 2, 60, 1, 0 },
+		{ "AUX2 Fan",		36, 2, 60, 1, 0 },
+		{ "AUX3 Fan",		37, 2, 60, 1, 0 },
+		{ "AUX4 Fan",		38, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x0014, "Abit AB9 Pro", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR",		 1, 0, 10, 1, 0 },
+		{ "DDR VTT",		 2, 0, 10, 1, 0 },
+		{ "CPU VTT 1.2V",	 3, 0, 10, 1, 0 },
+		{ "MCH & PCIE 1.5V",	 4, 0, 10, 1, 0 },
+		{ "MCH 2.5V",		 5, 0, 20, 1, 0 },
+		{ "ICH 1.05V",		 6, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "System ",		25, 1, 1, 1, 0 },
+		{ "PWM",		26, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "NB Fan",		33, 2, 60, 1, 0 },
+		{ "SYS Fan",		34, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x0015, "unknown", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR",		 1, 0, 20, 1, 0 },
+		{ "DDR VTT",		 2, 0, 10, 1, 0 },
+		{ "HyperTransport",	 3, 0, 10, 1, 0 },
+		{ "CPU VDDA 2.5V",	 5, 0, 20, 1, 0 },
+		{ "NB",			 4, 0, 10, 1, 0 },
+		{ "SB",			 6, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "SYS",		25, 1, 1, 1, 0 },
+		{ "PWM",		26, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "NB Fan",		33, 2, 60, 1, 0 },
+		{ "SYS Fan",		34, 2, 60, 1, 0 },
+		{ "AUX1 Fan",		33, 2, 60, 1, 0 },
+		{ "AUX2 Fan",		35, 2, 60, 1, 0 },
+		{ "AUX3 Fan",		36, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x0016, "AW9D-MAX", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR2",		 1, 0, 20, 1, 0 },
+		{ "DDR2 VTT",		 2, 0, 10, 1, 0 },
+		{ "CPU VTT 1.2V",	 3, 0, 10, 1, 0 },
+		{ "MCH & PCIE 1.5V",	 4, 0, 10, 1, 0 },
+		{ "MCH 2.5V",		 5, 0, 20, 1, 0 },
+		{ "ICH 1.05V",		 6, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "System ",		25, 1, 1, 1, 0 },
+		{ "PWM1",		26, 1, 1, 1, 0 },
+		{ "PWM2",		27, 1, 1, 1, 0 },
+		{ "PWM3",		28, 1, 1, 1, 0 },
+		{ "PWM4",		29, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "NB Fan",		33, 2, 60, 1, 0 },
+		{ "SYS Fan",		34, 2, 60, 1, 0 },
+		{ "AUX1 Fan",		35, 2, 60, 1, 0 },
+		{ "AUX2 Fan",		36, 2, 60, 1, 0 },
+		{ "AUX3 Fan",		37, 2, 60, 1, 0 },
+		{ "OTES1 Fan",		38, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x0017, "unknown", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR2",		 1, 0, 20, 1, 0 },
+		{ "DDR2 VTT",		 2, 0, 10, 1, 0 },
+		{ "HyperTransport",	 3, 0, 10, 1, 0 },
+		{ "CPU VDDA 2.5V",	 6, 0, 20, 1, 0 },
+		{ "NB 1.8V",		 4, 0, 10, 1, 0 },
+		{ "NB 1.2V ",		13, 0, 10, 1, 0 },
+		{ "SB 1.2V",		 5, 0, 10, 1, 0 },
+		{ "PCIE 1.2V",		12, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "ATX +3.3V",		10, 0, 20, 1, 0 },
+		{ "ATX 5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "System ",		26, 1, 1, 1, 0 },
+		{ "PWM",		27, 1, 1, 1, 0 },
+		{ "CPU FAN",		32, 2, 60, 1, 0 },
+		{ "SYS FAN",		34, 2, 60, 1, 0 },
+		{ "AUX1 FAN",		35, 2, 60, 1, 0 },
+		{ "AUX2 FAN",		36, 2, 60, 1, 0 },
+		{ "AUX3 FAN",		37, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x0018, "unknown", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR2",		 1, 0, 20, 1, 0 },
+		{ "DDR2 VTT",		 2, 0, 10, 1, 0 },
+		{ "CPU VTT",		 3, 0, 10, 1, 0 },
+		{ "MCH 1.25V",		 4, 0, 10, 1, 0 },
+		{ "ICHIO 1.5V",		 5, 0, 10, 1, 0 },
+		{ "ICH 1.05V",		 6, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "System ",		25, 1, 1, 1, 0 },
+		{ "PWM Phase1",		26, 1, 1, 1, 0 },
+		{ "PWM Phase2",		27, 1, 1, 1, 0 },
+		{ "PWM Phase3",		28, 1, 1, 1, 0 },
+		{ "PWM Phase4",		29, 1, 1, 1, 0 },
+		{ "PWM Phase5",		30, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "SYS Fan",		34, 2, 60, 1, 0 },
+		{ "AUX1 Fan",		33, 2, 60, 1, 0 },
+		{ "AUX2 Fan",		35, 2, 60, 1, 0 },
+		{ "AUX3 Fan",		36, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x0019, "unknown", {
+		{ "CPU Core",		 7, 0, 10, 1, 0 },
+		{ "DDR2",		13, 0, 20, 1, 0 },
+		{ "DDR2 VTT",		14, 0, 10, 1, 0 },
+		{ "CPU VTT",		 3, 0, 20, 1, 0 },
+		{ "NB 1.2V ",		 4, 0, 10, 1, 0 },
+		{ "SB 1.5V",		 6, 0, 10, 1, 0 },
+		{ "HyperTransport",	 5, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	12, 0, 60, 1, 0 },
+		{ "ATX +12V (4-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "ATX +3.3V",		10, 0, 20, 1, 0 },
+		{ "ATX 5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "System ",		25, 1, 1, 1, 0 },
+		{ "PWM Phase1",		26, 1, 1, 1, 0 },
+		{ "PWM Phase2",		27, 1, 1, 1, 0 },
+		{ "PWM Phase3",		28, 1, 1, 1, 0 },
+		{ "PWM Phase4",		29, 1, 1, 1, 0 },
+		{ "PWM Phase5",		30, 1, 1, 1, 0 },
+		{ "CPU FAN",		32, 2, 60, 1, 0 },
+		{ "SYS FAN",		34, 2, 60, 1, 0 },
+		{ "AUX1 FAN",		33, 2, 60, 1, 0 },
+		{ "AUX2 FAN",		35, 2, 60, 1, 0 },
+		{ "AUX3 FAN",		36, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x001A, "unknown", {
+		{ "CPU Core",		 0, 0, 10, 1, 0 },
+		{ "DDR2",		 1, 0, 20, 1, 0 },
+		{ "DDR2 VTT",		 2, 0, 10, 1, 0 },
+		{ "CPU VTT 1.2V",	 3, 0, 10, 1, 0 },
+		{ "MCH 1.25V",		 4, 0, 10, 1, 0 },
+		{ "ICHIO 1.5V",		 5, 0, 10, 1, 0 },
+		{ "ICH 1.05V",		 6, 0, 10, 1, 0 },
+		{ "ATX +12V (24-Pin)",	 7, 0, 60, 1, 0 },
+		{ "ATX +12V (8-pin)",	 8, 0, 60, 1, 0 },
+		{ "ATX +5V",		 9, 0, 30, 1, 0 },
+		{ "+3.3V",		10, 0, 20, 1, 0 },
+		{ "5VSB",		11, 0, 30, 1, 0 },
+		{ "CPU",		24, 1, 1, 1, 0 },
+		{ "System ",		25, 1, 1, 1, 0 },
+		{ "PWM ",		26, 1, 1, 1, 0 },
+		{ "PWM Phase2",		27, 1, 1, 1, 0 },
+		{ "PWM Phase3",		28, 1, 1, 1, 0 },
+		{ "PWM Phase4",		29, 1, 1, 1, 0 },
+		{ "PWM Phase5",		30, 1, 1, 1, 0 },
+		{ "CPU Fan",		32, 2, 60, 1, 0 },
+		{ "SYS Fan",		34, 2, 60, 1, 0 },
+		{ "AUX1 Fan",		33, 2, 60, 1, 0 },
+		{ "AUX2 Fan",		35, 2, 60, 1, 0 },
+		{ "AUX3 Fan",		36, 2, 60, 1, 0 },
+		{ NULL, 0, 0, 0, 0, 0 } }
+	},
+	{ 0x0000, NULL, { { NULL, 0, 0, 0, 0, 0 } } }
+};
+
+
+/* Insmod parameters */
+static int force;
+module_param(force, bool, 0);
+MODULE_PARM_DESC(force, "Set to one to force detection.");
+/* Default verbose is 1, since this driver is still in the testing phase */
+static int verbose = 1;
+module_param(verbose, bool, 0644);
+MODULE_PARM_DESC(verbose, "Enable/disable verbose error reporting");
+
+
+/* wait while the uguru is busy (usually after a write) */
+static int abituguru3_wait_while_busy(struct abituguru3_data *data)
+{
+	u8 x;
+	int timeout = ABIT_UGURU3_WAIT_TIMEOUT;
+
+	while ((x = inb_p(data->addr + ABIT_UGURU3_DATA)) &
+			ABIT_UGURU3_STATUS_BUSY) {
+		timeout--;
+		if (timeout == 0)
+			return x;
+		/* sleep a bit before our last try, to give the uGuru3 one
+		   last chance to respond. */
+		if (timeout == 1)
+			msleep(1);
+	}
+	return ABIT_UGURU3_SUCCESS;
+}
+
+/* wait till uguru is ready to be read */
+static int abituguru3_wait_for_read(struct abituguru3_data *data)
+{
+	u8 x;
+	int timeout = ABIT_UGURU3_WAIT_TIMEOUT;
+
+	while (!((x = inb_p(data->addr + ABIT_UGURU3_DATA)) &
+			ABIT_UGURU3_STATUS_READY_FOR_READ)) {
+		timeout--;
+		if (timeout == 0)
+			return x;
+		/* sleep a bit before our last try, to give the uGuru3 one
+		   last chance to respond. */
+		if (timeout == 1)
+			msleep(1);
+	}
+	return ABIT_UGURU3_SUCCESS;
+}
+
+/* This synchronizes us with the uGuru3's protocol state machine, this
+   must be done before each command. */
+static int abituguru3_synchronize(struct abituguru3_data *data)
+{
+	int x, timeout = ABIT_UGURU3_SYNCHRONIZE_TIMEOUT;
+
+	if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) {
+		ABIT_UGURU3_DEBUG("synchronize timeout during initial busy "
+			"wait, status: 0x%02x\n", x);
+		return -EIO;
+	}
+
+	outb(0x20, data->addr + ABIT_UGURU3_DATA);
+	if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) {
+		ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x20, "
+			"status: 0x%02x\n", x);
+		return -EIO;
+	}
+
+	outb(0x10, data->addr + ABIT_UGURU3_CMD);
+	if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) {
+		ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x10, "
+			"status: 0x%02x\n", x);
+		return -EIO;
+	}
+
+	outb(0x00, data->addr + ABIT_UGURU3_CMD);
+	if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) {
+		ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x00, "
+			"status: 0x%02x\n", x);
+		return -EIO;
+	}
+
+	if ((x = abituguru3_wait_for_read(data)) != ABIT_UGURU3_SUCCESS) {
+		ABIT_UGURU3_DEBUG("synchronize timeout waiting for read, "
+			"status: 0x%02x\n", x);
+		return -EIO;
+	}
+
+	while ((x = inb(data->addr + ABIT_UGURU3_CMD)) != 0xAC) {
+		timeout--;
+		if (timeout == 0) {
+			ABIT_UGURU3_DEBUG("synchronize timeout cmd does not "
+				"hold 0xAC after synchronize, cmd: 0x%02x\n",
+				x);
+			return -EIO;
+		}
+		msleep(1);
+	}
+	return 0;
+}
+
+/* Read count bytes from sensor sensor_addr in bank bank_addr and store the
+   result in buf */
+static int abituguru3_read(struct abituguru3_data *data, u8 bank, u8 offset,
+	u8 count, u8 *buf)
+{
+	int i, x;
+
+	if ((x = abituguru3_synchronize(data)))
+		return x;
+
+	outb(0x1A, data->addr + ABIT_UGURU3_DATA);
+	if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) {
+		ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after "
+			"sending 0x1A, status: 0x%02x\n", (unsigned int)bank,
+			(unsigned int)offset, x);
+		return -EIO;
+	}
+
+	outb(bank, data->addr + ABIT_UGURU3_CMD);
+	if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) {
+		ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after "
+			"sending the bank, status: 0x%02x\n",
+			(unsigned int)bank, (unsigned int)offset, x);
+		return -EIO;
+	}
+
+	outb(offset, data->addr + ABIT_UGURU3_CMD);
+	if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) {
+		ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after "
+			"sending the offset, status: 0x%02x\n",
+			(unsigned int)bank, (unsigned int)offset, x);
+		return -EIO;
+	}
+
+	outb(count, data->addr + ABIT_UGURU3_CMD);
+	if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) {
+		ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after "
+			"sending the count, status: 0x%02x\n",
+			(unsigned int)bank, (unsigned int)offset, x);
+		return -EIO;
+	}
+
+	for (i = 0; i < count; i++) {
+		if ((x = abituguru3_wait_for_read(data)) !=
+				ABIT_UGURU3_SUCCESS) {
+			ABIT_UGURU3_DEBUG("timeout reading byte %d from "
+				"0x%02x:0x%02x, status: 0x%02x\n", i,
+				(unsigned int)bank, (unsigned int)offset, x);
+			break;
+		}
+		buf[i] = inb(data->addr + ABIT_UGURU3_CMD);
+	}
+	return i;
+}
+
+/* Sensor settings are stored 1 byte per offset with the bytes
+   placed add consecutive offsets. */
+int abituguru3_read_increment_offset(struct abituguru3_data *data, u8 bank,
+	u8 offset, u8 count, u8 *buf, int offset_count)
+{
+	int i, x;
+
+	for (i = 0; i < offset_count; i++)
+		if ((x = abituguru3_read(data, bank, offset + i, count,
+				buf + i * count)) != count)
+			return i * count + (i && (x < 0)) ? 0 : x;
+
+	return i * count;
+}
+
+/* Following are the sysfs callback functions. These functions expect:
+   sensor_device_attribute_2->index:   index into the data->sensors array
+   sensor_device_attribute_2->nr:      register offset, bitmask or NA. */
+static struct abituguru3_data *abituguru3_update_device(struct device *dev);
+
+static ssize_t show_value(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	int value;
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru3_data *data = abituguru3_update_device(dev);
+	const struct abituguru3_sensor_info *sensor;
+
+	if (!data)
+		return -EIO;
+
+	sensor = &data->sensors[attr->index];
+
+	/* are we reading a setting, or is this a normal read? */
+	if (attr->nr)
+		value = data->settings[sensor->port][attr->nr];
+	else
+		value = data->value[sensor->port];
+
+	/* convert the value */
+	value = (value * sensor->multiplier) / sensor->divisor +
+		sensor->offset;
+
+	/* alternatively we could update the sensors settings struct for this,
+	   but then its contents would differ from the windows sw ini files */
+	if (sensor->type == ABIT_UGURU3_TEMP_SENSOR)
+		value *= 1000;
+
+	return sprintf(buf, "%d\n", value);
+}
+
+static ssize_t show_alarm(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	int port;
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru3_data *data = abituguru3_update_device(dev);
+
+	if (!data)
+		return -EIO;
+
+	port = data->sensors[attr->index].port;
+
+	/* See if the alarm bit for this sensor is set and if a bitmask is
+	   given in attr->nr also check if the alarm matches the type of alarm
+	   we're looking for (for volt it can be either low or high). The type
+	   is stored in a few readonly bits in the settings of the sensor. */
+	if ((data->alarms[port / 8] & (0x01 << (port % 8))) &&
+			(!attr->nr || (data->settings[port][0] & attr->nr)))
+		return sprintf(buf, "1\n");
+	else
+		return sprintf(buf, "0\n");
+}
+
+static ssize_t show_mask(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru3_data *data = dev_get_drvdata(dev);
+
+	if (data->settings[data->sensors[attr->index].port][0] & attr->nr)
+		return sprintf(buf, "1\n");
+	else
+		return sprintf(buf, "0\n");
+}
+
+static ssize_t show_label(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru3_data *data = dev_get_drvdata(dev);
+
+	return sprintf(buf, "%s\n", data->sensors[attr->index].name);
+}
+
+static ssize_t show_name(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	return sprintf(buf, "%s\n", ABIT_UGURU3_NAME);
+}
+
+/* Sysfs attr templates, the real entries are generated automatically. */
+static const
+struct sensor_device_attribute_2 abituguru3_sysfs_templ[3][10] = { {
+	SENSOR_ATTR_2(in%d_input, 0444, show_value, NULL, 0, 0),
+	SENSOR_ATTR_2(in%d_min, 0444, show_value, NULL, 1, 0),
+	SENSOR_ATTR_2(in%d_max, 0444, show_value, NULL, 2, 0),
+	SENSOR_ATTR_2(in%d_min_alarm, 0444, show_alarm, NULL,
+		ABIT_UGURU3_VOLT_LOW_ALARM_FLAG, 0),
+	SENSOR_ATTR_2(in%d_max_alarm, 0444, show_alarm, NULL,
+		ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG, 0),
+	SENSOR_ATTR_2(in%d_beep, 0444, show_mask, NULL,
+		ABIT_UGURU3_BEEP_ENABLE, 0),
+	SENSOR_ATTR_2(in%d_shutdown, 0444, show_mask, NULL,
+		ABIT_UGURU3_SHUTDOWN_ENABLE, 0),
+	SENSOR_ATTR_2(in%d_min_alarm_enable, 0444, show_mask, NULL,
+		ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE, 0),
+	SENSOR_ATTR_2(in%d_max_alarm_enable, 0444, show_mask, NULL,
+		ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE, 0),
+	SENSOR_ATTR_2(in%d_label, 0444, show_label, NULL, 0, 0)
+	}, {
+	SENSOR_ATTR_2(temp%d_input, 0444, show_value, NULL, 0, 0),
+	SENSOR_ATTR_2(temp%d_max, 0444, show_value, NULL, 1, 0),
+	SENSOR_ATTR_2(temp%d_crit, 0444, show_value, NULL, 2, 0),
+	SENSOR_ATTR_2(temp%d_alarm, 0444, show_alarm, NULL, 0, 0),
+	SENSOR_ATTR_2(temp%d_beep, 0444, show_mask, NULL,
+		ABIT_UGURU3_BEEP_ENABLE, 0),
+	SENSOR_ATTR_2(temp%d_shutdown, 0444, show_mask, NULL,
+		ABIT_UGURU3_SHUTDOWN_ENABLE, 0),
+	SENSOR_ATTR_2(temp%d_alarm_enable, 0444, show_mask, NULL,
+		ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE, 0),
+	SENSOR_ATTR_2(temp%d_label, 0444, show_label, NULL, 0, 0)
+	}, {
+	SENSOR_ATTR_2(fan%d_input, 0444, show_value, NULL, 0, 0),
+	SENSOR_ATTR_2(fan%d_min, 0444, show_value, NULL, 1, 0),
+	SENSOR_ATTR_2(fan%d_alarm, 0444, show_alarm, NULL, 0, 0),
+	SENSOR_ATTR_2(fan%d_beep, 0444, show_mask, NULL,
+		ABIT_UGURU3_BEEP_ENABLE, 0),
+	SENSOR_ATTR_2(fan%d_shutdown, 0444, show_mask, NULL,
+		ABIT_UGURU3_SHUTDOWN_ENABLE, 0),
+	SENSOR_ATTR_2(fan%d_alarm_enable, 0444, show_mask, NULL,
+		ABIT_UGURU3_FAN_LOW_ALARM_ENABLE, 0),
+	SENSOR_ATTR_2(fan%d_label, 0444, show_label, NULL, 0, 0)
+} };
+
+static struct sensor_device_attribute_2 abituguru3_sysfs_attr[] = {
+	SENSOR_ATTR_2(name, 0444, show_name, NULL, 0, 0),
+};
+
+static int __devinit abituguru3_probe(struct platform_device *pdev)
+{
+	const int no_sysfs_attr[3] = { 10, 8, 7 };
+	int sensor_index[3] = { 0, 1, 1 };
+	struct abituguru3_data *data;
+	int i, j, type, used, sysfs_names_free, sysfs_attr_i, res = -ENODEV;
+	char *sysfs_filename;
+	u8 buf[2];
+	u16 id;
+
+	if (!(data = kzalloc(sizeof(struct abituguru3_data), GFP_KERNEL)))
+		return -ENOMEM;
+
+	data->addr = platform_get_resource(pdev, IORESOURCE_IO, 0)->start;
+	mutex_init(&data->update_lock);
+	platform_set_drvdata(pdev, data);
+
+	/* Read the motherboard ID */
+	if ((i = abituguru3_read(data, ABIT_UGURU3_MISC_BANK,
+			ABIT_UGURU3_BOARD_ID, 2, buf)) != 2) {
+		goto abituguru3_probe_error;
+	}
+
+	/* Completely read the uGuru to see if one really is there */
+	if (!abituguru3_update_device(&pdev->dev))
+		goto abituguru3_probe_error;
+
+	/* lookup the ID in our motherboard table */
+	id = ((u16)buf[0] << 8) | (u16)buf[1];
+	for (i = 0; abituguru3_motherboards[i].id; i++)
+		if (abituguru3_motherboards[i].id == id)
+			break;
+	if (!abituguru3_motherboards[i].id) {
+		printk(KERN_ERR ABIT_UGURU3_NAME ": error unknown motherboard "
+			"ID: %04X. Please report this to the abituguru3 "
+			"maintainer (see MAINTAINERS)\n", (unsigned int)id);
+		goto abituguru3_probe_error;
+	}
+	data->sensors = abituguru3_motherboards[i].sensors;
+	printk(KERN_INFO ABIT_UGURU3_NAME ": found Abit uGuru3, motherboard "
+		"ID: %04X (%s)\n", (unsigned int)id,
+		abituguru3_motherboards[i].name);
+
+	/* Fill the sysfs attr array */
+	sysfs_attr_i = 0;
+	sysfs_filename = data->sysfs_names;
+	sysfs_names_free = ABIT_UGURU3_SYSFS_NAMES_LENGTH;
+	for (i = 0; data->sensors[i].name; i++) {
+		/* Fail safe check, this should never happen! */
+		if (i >= ABIT_UGURU3_MAX_NO_SENSORS) {
+			printk(KERN_ERR ABIT_UGURU3_NAME
+				": Fatal error motherboard has more sensors "
+				"then ABIT_UGURU3_MAX_NO_SENSORS. This should "
+				"never happen please report to the abituguru3 "
+				"maintainer (see MAINTAINERS)\n");
+			res = -ENAMETOOLONG;
+			goto abituguru3_probe_error;
+		}
+		type = data->sensors[i].type;
+		for (j = 0; j < no_sysfs_attr[type]; j++) {
+			used = snprintf(sysfs_filename, sysfs_names_free,
+				abituguru3_sysfs_templ[type][j].dev_attr.attr.
+				name, sensor_index[type]) + 1;
+			data->sysfs_attr[sysfs_attr_i] =
+				abituguru3_sysfs_templ[type][j];
+			data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
+				sysfs_filename;
+			data->sysfs_attr[sysfs_attr_i].index = i;
+			sysfs_filename += used;
+			sysfs_names_free -= used;
+			sysfs_attr_i++;
+		}
+		sensor_index[type]++;
+	}
+	/* Fail safe check, this should never happen! */
+	if (sysfs_names_free < 0) {
+		printk(KERN_ERR ABIT_UGURU3_NAME
+			": Fatal error ran out of space for sysfs attr names. "
+			"This should never happen please report to the "
+			"abituguru3 maintainer (see MAINTAINERS)\n");
+		res = -ENAMETOOLONG;
+		goto abituguru3_probe_error;
+	}
+
+	/* Register sysfs hooks */
+	for (i = 0; i < sysfs_attr_i; i++)
+		if (device_create_file(&pdev->dev,
+				&data->sysfs_attr[i].dev_attr))
+			goto abituguru3_probe_error;
+	for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++)
+		if (device_create_file(&pdev->dev,
+				&abituguru3_sysfs_attr[i].dev_attr))
+			goto abituguru3_probe_error;
+
+	data->class_dev = hwmon_device_register(&pdev->dev);
+	if (IS_ERR(data->class_dev)) {
+		res = PTR_ERR(data->class_dev);
+		goto abituguru3_probe_error;
+	}
+
+	return 0; /* success */
+
+abituguru3_probe_error:
+	for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++)
+		device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
+	for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++)
+		device_remove_file(&pdev->dev,
+			&abituguru3_sysfs_attr[i].dev_attr);
+	kfree(data);
+	return res;
+}
+
+static int __devexit abituguru3_remove(struct platform_device *pdev)
+{
+	int i;
+	struct abituguru3_data *data = platform_get_drvdata(pdev);
+
+	platform_set_drvdata(pdev, NULL);
+	hwmon_device_unregister(data->class_dev);
+	for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++)
+		device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
+	for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++)
+		device_remove_file(&pdev->dev,
+			&abituguru3_sysfs_attr[i].dev_attr);
+	kfree(data);
+
+	return 0;
+}
+
+static struct abituguru3_data *abituguru3_update_device(struct device *dev)
+{
+	int i;
+	struct abituguru3_data *data = dev_get_drvdata(dev);
+
+	mutex_lock(&data->update_lock);
+	if (!data->valid || time_after(jiffies, data->last_updated + HZ)) {
+		/* Clear data->valid while updating */
+		data->valid = 0;
+		/* Read alarms */
+		if (abituguru3_read_increment_offset(data,
+				ABIT_UGURU3_SETTINGS_BANK,
+				ABIT_UGURU3_ALARMS_START,
+				1, data->alarms, 48/8) != (48/8))
+			goto LEAVE_UPDATE;
+		/* Read in and temp sensors (3 byte settings / sensor) */
+		for (i = 0; i < 32; i++) {
+			if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK,
+					ABIT_UGURU3_VALUES_START + i,
+					1, &data->value[i]) != 1)
+				goto LEAVE_UPDATE;
+			if (abituguru3_read_increment_offset(data,
+					ABIT_UGURU3_SETTINGS_BANK,
+					ABIT_UGURU3_SETTINGS_START + i * 3,
+					1,
+					data->settings[i], 3) != 3)
+				goto LEAVE_UPDATE;
+		}
+		/* Read temp sensors (2 byte settings / sensor) */
+		for (i = 0; i < 16; i++) {
+			if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK,
+					ABIT_UGURU3_VALUES_START + 32 + i,
+					1, &data->value[32 + i]) != 1)
+				goto LEAVE_UPDATE;
+			if (abituguru3_read_increment_offset(data,
+					ABIT_UGURU3_SETTINGS_BANK,
+					ABIT_UGURU3_SETTINGS_START + 32 * 3 +
+						i * 2, 1,
+					data->settings[32 + i], 2) != 2)
+				goto LEAVE_UPDATE;
+		}
+		data->last_updated = jiffies;
+		data->valid = 1;
+	}
+LEAVE_UPDATE:
+	mutex_unlock(&data->update_lock);
+	if (data->valid)
+		return data;
+	else
+		return NULL;
+}
+
+#ifdef CONFIG_PM
+static int abituguru3_suspend(struct platform_device *pdev, pm_message_t state)
+{
+	struct abituguru3_data *data = platform_get_drvdata(pdev);
+	/* make sure all communications with the uguru3 are done and no new
+	   ones are started */
+	mutex_lock(&data->update_lock);
+	return 0;
+}
+
+static int abituguru3_resume(struct platform_device *pdev)
+{
+	struct abituguru3_data *data = platform_get_drvdata(pdev);
+	mutex_unlock(&data->update_lock);
+	return 0;
+}
+#else
+#define abituguru3_suspend	NULL
+#define abituguru3_resume	NULL
+#endif /* CONFIG_PM */
+
+static struct platform_driver abituguru3_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= ABIT_UGURU3_NAME,
+	},
+	.probe	= abituguru3_probe,
+	.remove	= __devexit_p(abituguru3_remove),
+	.suspend = abituguru3_suspend,
+	.resume = abituguru3_resume
+};
+
+static int __init abituguru3_detect(void)
+{
+	/* See if there is an uguru3 there. An idle uGuru3 will hold 0x00 or
+	   0x08 at DATA and 0xAC at CMD. Sometimes the uGuru3 will hold 0x05
+	   at CMD instead, why is unknown. So we test for 0x05 too. */
+	u8 data_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_DATA);
+	u8 cmd_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_CMD);
+	if (((data_val == 0x00) || (data_val == 0x08)) &&
+			((cmd_val == 0xAC) || (cmd_val == 0x05)))
+		return ABIT_UGURU3_BASE;
+
+	ABIT_UGURU3_DEBUG("no Abit uGuru3 found, data = 0x%02X, cmd = "
+		"0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val);
+
+	if (force) {
+		printk(KERN_INFO ABIT_UGURU3_NAME ": Assuming Abit uGuru3 is "
+				"present because of \"force\" parameter\n");
+		return ABIT_UGURU3_BASE;
+	}
+
+	/* No uGuru3 found */
+	return -ENODEV;
+}
+
+static struct platform_device *abituguru3_pdev;
+
+static int __init abituguru3_init(void)
+{
+	int address, err;
+	struct resource res = { .flags = IORESOURCE_IO };
+
+	address = abituguru3_detect();
+	if (address < 0)
+		return address;
+
+	err = platform_driver_register(&abituguru3_driver);
+	if (err)
+		goto exit;
+
+	abituguru3_pdev = platform_device_alloc(ABIT_UGURU3_NAME, address);
+	if (!abituguru3_pdev) {
+		printk(KERN_ERR ABIT_UGURU3_NAME
+			": Device allocation failed\n");
+		err = -ENOMEM;
+		goto exit_driver_unregister;
+	}
+
+	res.start = address;
+	res.end = address + ABIT_UGURU3_REGION_LENGTH - 1;
+	res.name = ABIT_UGURU3_NAME;
+
+	err = platform_device_add_resources(abituguru3_pdev, &res, 1);
+	if (err) {
+		printk(KERN_ERR ABIT_UGURU3_NAME
+			": Device resource addition failed (%d)\n", err);
+		goto exit_device_put;
+	}
+
+	err = platform_device_add(abituguru3_pdev);
+	if (err) {
+		printk(KERN_ERR ABIT_UGURU3_NAME
+			": Device addition failed (%d)\n", err);
+		goto exit_device_put;
+	}
+
+	return 0;
+
+exit_device_put:
+	platform_device_put(abituguru3_pdev);
+exit_driver_unregister:
+	platform_driver_unregister(&abituguru3_driver);
+exit:
+	return err;
+}
+
+static void __exit abituguru3_exit(void)
+{
+	platform_device_unregister(abituguru3_pdev);
+	platform_driver_unregister(&abituguru3_driver);
+}
+
+MODULE_AUTHOR("Hans de Goede <j.w.r.degoede@hhs.nl>");
+MODULE_DESCRIPTION("Abit uGuru3 Sensor device");
+MODULE_LICENSE("GPL");
+
+module_init(abituguru3_init);
+module_exit(abituguru3_exit);
diff --git a/drivers/hwmon/coretemp.c b/drivers/hwmon/coretemp.c
index 6d54c8c..7c17952 100644
--- a/drivers/hwmon/coretemp.c
+++ b/drivers/hwmon/coretemp.c
@@ -318,7 +318,7 @@
 }
 
 #ifdef CONFIG_HOTPLUG_CPU
-void coretemp_device_remove(unsigned int cpu)
+static void coretemp_device_remove(unsigned int cpu)
 {
 	struct pdev_entry *p, *n;
 	mutex_lock(&pdev_list_mutex);
diff --git a/drivers/hwmon/dme1737.c b/drivers/hwmon/dme1737.c
new file mode 100644
index 0000000..be3aaa5
--- /dev/null
+++ b/drivers/hwmon/dme1737.c
@@ -0,0 +1,2080 @@
+/*
+ * dme1737.c - driver for the SMSC DME1737 and Asus A8000 Super-I/O chips
+ *             integrated hardware monitoring features.
+ * Copyright (c) 2007 Juerg Haefliger <juergh@gmail.com>
+ *
+ * This driver is based on the LM85 driver. The hardware monitoring
+ * capabilities of the DME1737 are very similar to the LM85 with some
+ * additional features. Even though the DME1737 is a Super-I/O chip, the
+ * hardware monitoring registers are only accessible via SMBus.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/hwmon-vid.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <asm/io.h>
+
+/* Module load parameters */
+static int force_start;
+module_param(force_start, bool, 0);
+MODULE_PARM_DESC(force_start, "Force the chip to start monitoring inputs");
+
+/* Addresses to scan */
+static unsigned short normal_i2c[] = {0x2c, 0x2d, 0x2e, I2C_CLIENT_END};
+
+/* Insmod parameters */
+I2C_CLIENT_INSMOD_1(dme1737);
+
+/* ---------------------------------------------------------------------
+ * Registers
+ *
+ * The sensors are defined as follows:
+ *
+ * Voltages                          Temperatures
+ * --------                          ------------
+ * in0   +5VTR (+5V stdby)           temp1   Remote diode 1
+ * in1   Vccp  (proc core)           temp2   Internal temp
+ * in2   VCC   (internal +3.3V)      temp3   Remote diode 2
+ * in3   +5V
+ * in4   +12V
+ * in5   VTR   (+3.3V stby)
+ * in6   Vbat
+ *
+ * --------------------------------------------------------------------- */
+
+/* Voltages (in) numbered 0-6 (ix) */
+#define	DME1737_REG_IN(ix)		((ix) < 5 ? 0x20 + (ix) \
+						  : 0x94 + (ix))
+#define	DME1737_REG_IN_MIN(ix)		((ix) < 5 ? 0x44 + (ix) * 2 \
+						  : 0x91 + (ix) * 2)
+#define	DME1737_REG_IN_MAX(ix)		((ix) < 5 ? 0x45 + (ix) * 2 \
+						  : 0x92 + (ix) * 2)
+
+/* Temperatures (temp) numbered 0-2 (ix) */
+#define DME1737_REG_TEMP(ix)		(0x25 + (ix))
+#define DME1737_REG_TEMP_MIN(ix)	(0x4e + (ix) * 2)
+#define DME1737_REG_TEMP_MAX(ix)	(0x4f + (ix) * 2)
+#define DME1737_REG_TEMP_OFFSET(ix)	((ix) == 0 ? 0x1f \
+						   : 0x1c + (ix))
+
+/* Voltage and temperature LSBs
+ * The LSBs (4 bits each) are stored in 5 registers with the following layouts:
+ *    IN_TEMP_LSB(0) = [in5, in6]
+ *    IN_TEMP_LSB(1) = [temp3, temp1]
+ *    IN_TEMP_LSB(2) = [in4, temp2]
+ *    IN_TEMP_LSB(3) = [in3, in0]
+ *    IN_TEMP_LSB(4) = [in2, in1] */
+#define DME1737_REG_IN_TEMP_LSB(ix)	(0x84 + (ix))
+static const u8 DME1737_REG_IN_LSB[] = {3, 4, 4, 3, 2, 0, 0};
+static const u8 DME1737_REG_IN_LSB_SHL[] = {4, 4, 0, 0, 0, 0, 4};
+static const u8 DME1737_REG_TEMP_LSB[] = {1, 2, 1};
+static const u8 DME1737_REG_TEMP_LSB_SHL[] = {4, 4, 0};
+
+/* Fans numbered 0-5 (ix) */
+#define DME1737_REG_FAN(ix)		((ix) < 4 ? 0x28 + (ix) * 2 \
+						  : 0xa1 + (ix) * 2)
+#define DME1737_REG_FAN_MIN(ix)		((ix) < 4 ? 0x54 + (ix) * 2 \
+						  : 0xa5 + (ix) * 2)
+#define DME1737_REG_FAN_OPT(ix)		((ix) < 4 ? 0x90 + (ix) \
+						  : 0xb2 + (ix))
+#define DME1737_REG_FAN_MAX(ix)		(0xb4 + (ix)) /* only for fan[4-5] */
+
+/* PWMs numbered 0-2, 4-5 (ix) */
+#define DME1737_REG_PWM(ix)		((ix) < 3 ? 0x30 + (ix) \
+						  : 0xa1 + (ix))
+#define DME1737_REG_PWM_CONFIG(ix)	(0x5c + (ix)) /* only for pwm[0-2] */
+#define DME1737_REG_PWM_MIN(ix)		(0x64 + (ix)) /* only for pwm[0-2] */
+#define DME1737_REG_PWM_FREQ(ix)	((ix) < 3 ? 0x5f + (ix) \
+						  : 0xa3 + (ix))
+/* The layout of the ramp rate registers is different from the other pwm
+ * registers. The bits for the 3 PWMs are stored in 2 registers:
+ *    PWM_RR(0) = [OFF3, OFF2,  OFF1,  RES,   RR1E, RR1-2, RR1-1, RR1-0]
+ *    PWM_RR(1) = [RR2E, RR2-2, RR2-1, RR2-0, RR3E, RR3-2, RR3-1, RR3-0] */
+#define DME1737_REG_PWM_RR(ix)		(0x62 + (ix)) /* only for pwm[0-2] */
+
+/* Thermal zones 0-2 */
+#define DME1737_REG_ZONE_LOW(ix)	(0x67 + (ix))
+#define DME1737_REG_ZONE_ABS(ix)	(0x6a + (ix))
+/* The layout of the hysteresis registers is different from the other zone
+ * registers. The bits for the 3 zones are stored in 2 registers:
+ *    ZONE_HYST(0) = [H1-3,  H1-2,  H1-1, H1-0, H2-3, H2-2, H2-1, H2-0]
+ *    ZONE_HYST(1) = [H3-3,  H3-2,  H3-1, H3-0, RES,  RES,  RES,  RES] */
+#define DME1737_REG_ZONE_HYST(ix)	(0x6d + (ix))
+
+/* Alarm registers and bit mapping
+ * The 3 8-bit alarm registers will be concatenated to a single 32-bit
+ * alarm value [0, ALARM3, ALARM2, ALARM1]. */
+#define DME1737_REG_ALARM1		0x41
+#define DME1737_REG_ALARM2		0x42
+#define DME1737_REG_ALARM3		0x83
+static const u8 DME1737_BIT_ALARM_IN[] = {0, 1, 2, 3, 8, 16, 17};
+static const u8 DME1737_BIT_ALARM_TEMP[] = {4, 5, 6};
+static const u8 DME1737_BIT_ALARM_FAN[] = {10, 11, 12, 13, 22, 23};
+
+/* Miscellaneous registers */
+#define DME1737_REG_COMPANY		0x3e
+#define DME1737_REG_VERSTEP		0x3f
+#define DME1737_REG_CONFIG		0x40
+#define DME1737_REG_CONFIG2		0x7f
+#define DME1737_REG_VID			0x43
+#define DME1737_REG_TACH_PWM		0x81
+
+/* ---------------------------------------------------------------------
+ * Misc defines
+ * --------------------------------------------------------------------- */
+
+/* Chip identification */
+#define DME1737_COMPANY_SMSC	0x5c
+#define DME1737_VERSTEP		0x88
+#define DME1737_VERSTEP_MASK	0xf8
+
+/* ---------------------------------------------------------------------
+ * Data structures and manipulation thereof
+ * --------------------------------------------------------------------- */
+
+struct dme1737_data {
+	struct i2c_client client;
+	struct class_device *class_dev;
+
+	struct mutex update_lock;
+	int valid;			/* !=0 if following fields are valid */
+	unsigned long last_update;	/* in jiffies */
+	unsigned long last_vbat;	/* in jiffies */
+
+	u8 vid;
+	u8 pwm_rr_en;
+	u8 has_pwm;
+	u8 has_fan;
+
+	/* Register values */
+	u16 in[7];
+	u8  in_min[7];
+	u8  in_max[7];
+	s16 temp[3];
+	s8  temp_min[3];
+	s8  temp_max[3];
+	s8  temp_offset[3];
+	u8  config;
+	u8  config2;
+	u8  vrm;
+	u16 fan[6];
+	u16 fan_min[6];
+	u8  fan_max[2];
+	u8  fan_opt[6];
+	u8  pwm[6];
+	u8  pwm_min[3];
+	u8  pwm_config[3];
+	u8  pwm_acz[3];
+	u8  pwm_freq[6];
+	u8  pwm_rr[2];
+	u8  zone_low[3];
+	u8  zone_abs[3];
+	u8  zone_hyst[2];
+	u32 alarms;
+};
+
+/* Nominal voltage values */
+static const int IN_NOMINAL[] = {5000, 2250, 3300, 5000, 12000, 3300, 3300};
+
+/* Voltage input
+ * Voltage inputs have 16 bits resolution, limit values have 8 bits
+ * resolution. */
+static inline int IN_FROM_REG(int reg, int ix, int res)
+{
+	return (reg * IN_NOMINAL[ix] + (3 << (res - 3))) / (3 << (res - 2));
+}
+
+static inline int IN_TO_REG(int val, int ix)
+{
+	return SENSORS_LIMIT((val * 192 + IN_NOMINAL[ix] / 2) /
+			     IN_NOMINAL[ix], 0, 255);
+}
+
+/* Temperature input
+ * The register values represent temperatures in 2's complement notation from
+ * -127 degrees C to +127 degrees C. Temp inputs have 16 bits resolution, limit
+ * values have 8 bits resolution. */
+static inline int TEMP_FROM_REG(int reg, int res)
+{
+	return (reg * 1000) >> (res - 8);
+}
+
+static inline int TEMP_TO_REG(int val)
+{
+	return SENSORS_LIMIT((val < 0 ? val - 500 : val + 500) / 1000,
+			     -128, 127);
+}
+
+/* Temperature range */
+static const int TEMP_RANGE[] = {2000, 2500, 3333, 4000, 5000, 6666, 8000,
+				 10000, 13333, 16000, 20000, 26666, 32000,
+				 40000, 53333, 80000};
+
+static inline int TEMP_RANGE_FROM_REG(int reg)
+{
+	return TEMP_RANGE[(reg >> 4) & 0x0f];
+}
+
+static int TEMP_RANGE_TO_REG(int val, int reg)
+{
+	int i;
+
+	for (i = 15; i > 0; i--) {
+		if (val > (TEMP_RANGE[i] + TEMP_RANGE[i - 1] + 1) / 2) {
+			break;
+		}
+	}
+
+	return (reg & 0x0f) | (i << 4);
+}
+
+/* Temperature hysteresis
+ * Register layout:
+ *    reg[0] = [H1-3, H1-2, H1-1, H1-0, H2-3, H2-2, H2-1, H2-0]
+ *    reg[1] = [H3-3, H3-2, H3-1, H3-0, xxxx, xxxx, xxxx, xxxx] */
+static inline int TEMP_HYST_FROM_REG(int reg, int ix)
+{
+	return (((ix == 1) ? reg : reg >> 4) & 0x0f) * 1000;
+}
+
+static inline int TEMP_HYST_TO_REG(int val, int ix, int reg)
+{
+	int hyst = SENSORS_LIMIT((val + 500) / 1000, 0, 15);
+
+	return (ix == 1) ? (reg & 0xf0) | hyst : (reg & 0x0f) | (hyst << 4);
+}
+
+/* Fan input RPM */
+static inline int FAN_FROM_REG(int reg, int tpc)
+{
+	return (reg == 0 || reg == 0xffff) ? 0 :
+		(tpc == 0) ? 90000 * 60 / reg : tpc * reg;
+}
+
+static inline int FAN_TO_REG(int val, int tpc)
+{
+	return SENSORS_LIMIT((tpc == 0) ? 90000 * 60 / val : val / tpc,
+			     0, 0xffff);
+}
+
+/* Fan TPC (tach pulse count)
+ * Converts a register value to a TPC multiplier or returns 0 if the tachometer
+ * is configured in legacy (non-tpc) mode */
+static inline int FAN_TPC_FROM_REG(int reg)
+{
+	return (reg & 0x20) ? 0 : 60 >> (reg & 0x03);
+}
+
+/* Fan type
+ * The type of a fan is expressed in number of pulses-per-revolution that it
+ * emits */
+static inline int FAN_TYPE_FROM_REG(int reg)
+{
+	int edge = (reg >> 1) & 0x03;
+
+	return (edge > 0) ? 1 << (edge - 1) : 0;
+}
+
+static inline int FAN_TYPE_TO_REG(int val, int reg)
+{
+	int edge = (val == 4) ? 3 : val;
+
+	return (reg & 0xf9) | (edge << 1);
+}
+
+/* Fan max RPM */
+static const int FAN_MAX[] = {0x54, 0x38, 0x2a, 0x21, 0x1c, 0x18, 0x15, 0x12,
+			      0x11, 0x0f, 0x0e};
+
+static int FAN_MAX_FROM_REG(int reg)
+{
+	int i;
+
+	for (i = 10; i > 0; i--) {
+		if (reg == FAN_MAX[i]) {
+			break;
+		}
+	}
+
+	return 1000 + i * 500;
+}
+
+static int FAN_MAX_TO_REG(int val)
+{
+	int i;
+
+	for (i = 10; i > 0; i--) {
+		if (val > (1000 + (i - 1) * 500)) {
+			break;
+		}
+	}
+
+	return FAN_MAX[i];
+}
+
+/* PWM enable
+ * Register to enable mapping:
+ * 000:  2  fan on zone 1 auto
+ * 001:  2  fan on zone 2 auto
+ * 010:  2  fan on zone 3 auto
+ * 011:  0  fan full on
+ * 100: -1  fan disabled
+ * 101:  2  fan on hottest of zones 2,3 auto
+ * 110:  2  fan on hottest of zones 1,2,3 auto
+ * 111:  1  fan in manual mode */
+static inline int PWM_EN_FROM_REG(int reg)
+{
+	static const int en[] = {2, 2, 2, 0, -1, 2, 2, 1};
+
+	return en[(reg >> 5) & 0x07];
+}
+
+static inline int PWM_EN_TO_REG(int val, int reg)
+{
+	int en = (val == 1) ? 7 : 3;
+
+	return (reg & 0x1f) | ((en & 0x07) << 5);
+}
+
+/* PWM auto channels zone
+ * Register to auto channels zone mapping (ACZ is a bitfield with bit x
+ * corresponding to zone x+1):
+ * 000: 001  fan on zone 1 auto
+ * 001: 010  fan on zone 2 auto
+ * 010: 100  fan on zone 3 auto
+ * 011: 000  fan full on
+ * 100: 000  fan disabled
+ * 101: 110  fan on hottest of zones 2,3 auto
+ * 110: 111  fan on hottest of zones 1,2,3 auto
+ * 111: 000  fan in manual mode */
+static inline int PWM_ACZ_FROM_REG(int reg)
+{
+	static const int acz[] = {1, 2, 4, 0, 0, 6, 7, 0};
+
+	return acz[(reg >> 5) & 0x07];
+}
+
+static inline int PWM_ACZ_TO_REG(int val, int reg)
+{
+	int acz = (val == 4) ? 2 : val - 1;
+
+	return (reg & 0x1f) | ((acz & 0x07) << 5);
+}
+
+/* PWM frequency */
+static const int PWM_FREQ[] = {11, 15, 22, 29, 35, 44, 59, 88,
+			       15000, 20000, 30000, 25000, 0, 0, 0, 0};
+
+static inline int PWM_FREQ_FROM_REG(int reg)
+{
+	return PWM_FREQ[reg & 0x0f];
+}
+
+static int PWM_FREQ_TO_REG(int val, int reg)
+{
+	int i;
+
+	/* the first two cases are special - stupid chip design! */
+	if (val > 27500) {
+		i = 10;
+	} else if (val > 22500) {
+		i = 11;
+	} else {
+		for (i = 9; i > 0; i--) {
+			if (val > (PWM_FREQ[i] + PWM_FREQ[i - 1] + 1) / 2) {
+				break;
+			}
+		}
+	}
+
+	return (reg & 0xf0) | i;
+}
+
+/* PWM ramp rate
+ * Register layout:
+ *    reg[0] = [OFF3,  OFF2,  OFF1,  RES,   RR1-E, RR1-2, RR1-1, RR1-0]
+ *    reg[1] = [RR2-E, RR2-2, RR2-1, RR2-0, RR3-E, RR3-2, RR3-1, RR3-0] */
+static const u8 PWM_RR[] = {206, 104, 69, 41, 26, 18, 10, 5};
+
+static inline int PWM_RR_FROM_REG(int reg, int ix)
+{
+	int rr = (ix == 1) ? reg >> 4 : reg;
+
+	return (rr & 0x08) ? PWM_RR[rr & 0x07] : 0;
+}
+
+static int PWM_RR_TO_REG(int val, int ix, int reg)
+{
+	int i;
+
+	for (i = 0; i < 7; i++) {
+		if (val > (PWM_RR[i] + PWM_RR[i + 1] + 1) / 2) {
+			break;
+		}
+	}
+
+	return (ix == 1) ? (reg & 0x8f) | (i << 4) : (reg & 0xf8) | i;
+}
+
+/* PWM ramp rate enable */
+static inline int PWM_RR_EN_FROM_REG(int reg, int ix)
+{
+	return PWM_RR_FROM_REG(reg, ix) ? 1 : 0;
+}
+
+static inline int PWM_RR_EN_TO_REG(int val, int ix, int reg)
+{
+	int en = (ix == 1) ? 0x80 : 0x08;
+
+	return val ? reg | en : reg & ~en;
+}
+
+/* PWM min/off
+ * The PWM min/off bits are part of the PMW ramp rate register 0 (see above for
+ * the register layout). */
+static inline int PWM_OFF_FROM_REG(int reg, int ix)
+{
+	return (reg >> (ix + 5)) & 0x01;
+}
+
+static inline int PWM_OFF_TO_REG(int val, int ix, int reg)
+{
+	return (reg & ~(1 << (ix + 5))) | ((val & 0x01) << (ix + 5));
+}
+
+/* ---------------------------------------------------------------------
+ * Device I/O access
+ * --------------------------------------------------------------------- */
+
+static u8 dme1737_read(struct i2c_client *client, u8 reg)
+{
+	s32 val = i2c_smbus_read_byte_data(client, reg);
+
+	if (val < 0) {
+		dev_warn(&client->dev, "Read from register 0x%02x failed! "
+			 "Please report to the driver maintainer.\n", reg);
+	}
+
+	return val;
+}
+
+static s32 dme1737_write(struct i2c_client *client, u8 reg, u8 value)
+{
+	s32 res = i2c_smbus_write_byte_data(client, reg, value);
+
+	if (res < 0) {
+		dev_warn(&client->dev, "Write to register 0x%02x failed! "
+			 "Please report to the driver maintainer.\n", reg);
+	}
+
+	return res;
+}
+
+static struct dme1737_data *dme1737_update_device(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct dme1737_data *data = i2c_get_clientdata(client);
+	int ix;
+	u8 lsb[5];
+
+	mutex_lock(&data->update_lock);
+
+	/* Enable a Vbat monitoring cycle every 10 mins */
+	if (time_after(jiffies, data->last_vbat + 600 * HZ) || !data->valid) {
+		dme1737_write(client, DME1737_REG_CONFIG, dme1737_read(client,
+						DME1737_REG_CONFIG) | 0x10);
+		data->last_vbat = jiffies;
+	}
+
+	/* Sample register contents every 1 sec */
+	if (time_after(jiffies, data->last_update + HZ) || !data->valid) {
+		data->vid = dme1737_read(client, DME1737_REG_VID) & 0x3f;
+
+		/* In (voltage) registers */
+		for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) {
+			/* Voltage inputs are stored as 16 bit values even
+			 * though they have only 12 bits resolution. This is
+			 * to make it consistent with the temp inputs. */
+			data->in[ix] = dme1737_read(client,
+					DME1737_REG_IN(ix)) << 8;
+			data->in_min[ix] = dme1737_read(client,
+					DME1737_REG_IN_MIN(ix));
+			data->in_max[ix] = dme1737_read(client,
+					DME1737_REG_IN_MAX(ix));
+		}
+
+		/* Temp registers */
+		for (ix = 0; ix < ARRAY_SIZE(data->temp); ix++) {
+			/* Temp inputs are stored as 16 bit values even
+			 * though they have only 12 bits resolution. This is
+			 * to take advantage of implicit conversions between
+			 * register values (2's complement) and temp values
+			 * (signed decimal). */
+			data->temp[ix] = dme1737_read(client,
+					DME1737_REG_TEMP(ix)) << 8;
+			data->temp_min[ix] = dme1737_read(client,
+					DME1737_REG_TEMP_MIN(ix));
+			data->temp_max[ix] = dme1737_read(client,
+					DME1737_REG_TEMP_MAX(ix));
+			data->temp_offset[ix] = dme1737_read(client,
+					DME1737_REG_TEMP_OFFSET(ix));
+		}
+
+		/* In and temp LSB registers
+		 * The LSBs are latched when the MSBs are read, so the order in
+		 * which the registers are read (MSB first, then LSB) is
+		 * important! */
+		for (ix = 0; ix < ARRAY_SIZE(lsb); ix++) {
+			lsb[ix] = dme1737_read(client,
+					DME1737_REG_IN_TEMP_LSB(ix));
+		}
+		for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) {
+			data->in[ix] |= (lsb[DME1737_REG_IN_LSB[ix]] <<
+					DME1737_REG_IN_LSB_SHL[ix]) & 0xf0;
+		}
+		for (ix = 0; ix < ARRAY_SIZE(data->temp); ix++) {
+			data->temp[ix] |= (lsb[DME1737_REG_TEMP_LSB[ix]] <<
+					DME1737_REG_TEMP_LSB_SHL[ix]) & 0xf0;
+		}
+
+		/* Fan registers */
+		for (ix = 0; ix < ARRAY_SIZE(data->fan); ix++) {
+			/* Skip reading registers if optional fans are not
+			 * present */
+			if (!(data->has_fan & (1 << ix))) {
+				continue;
+			}
+			data->fan[ix] = dme1737_read(client,
+					DME1737_REG_FAN(ix));
+			data->fan[ix] |= dme1737_read(client,
+					DME1737_REG_FAN(ix) + 1) << 8;
+			data->fan_min[ix] = dme1737_read(client,
+					DME1737_REG_FAN_MIN(ix));
+			data->fan_min[ix] |= dme1737_read(client,
+					DME1737_REG_FAN_MIN(ix) + 1) << 8;
+			data->fan_opt[ix] = dme1737_read(client,
+					DME1737_REG_FAN_OPT(ix));
+			/* fan_max exists only for fan[5-6] */
+			if (ix > 3) {
+				data->fan_max[ix - 4] = dme1737_read(client,
+					DME1737_REG_FAN_MAX(ix));
+			}
+		}
+
+		/* PWM registers */
+		for (ix = 0; ix < ARRAY_SIZE(data->pwm); ix++) {
+			/* Skip reading registers if optional PWMs are not
+			 * present */
+			if (!(data->has_pwm & (1 << ix))) {
+				continue;
+			}
+			data->pwm[ix] = dme1737_read(client,
+					DME1737_REG_PWM(ix));
+			data->pwm_freq[ix] = dme1737_read(client,
+					DME1737_REG_PWM_FREQ(ix));
+			/* pwm_config and pwm_min exist only for pwm[1-3] */
+			if (ix < 3) {
+				data->pwm_config[ix] = dme1737_read(client,
+						DME1737_REG_PWM_CONFIG(ix));
+				data->pwm_min[ix] = dme1737_read(client,
+						DME1737_REG_PWM_MIN(ix));
+			}
+		}
+		for (ix = 0; ix < ARRAY_SIZE(data->pwm_rr); ix++) {
+			data->pwm_rr[ix] = dme1737_read(client,
+						DME1737_REG_PWM_RR(ix));
+		}
+
+		/* Thermal zone registers */
+		for (ix = 0; ix < ARRAY_SIZE(data->zone_low); ix++) {
+			data->zone_low[ix] = dme1737_read(client,
+					DME1737_REG_ZONE_LOW(ix));
+			data->zone_abs[ix] = dme1737_read(client,
+					DME1737_REG_ZONE_ABS(ix));
+		}
+		for (ix = 0; ix < ARRAY_SIZE(data->zone_hyst); ix++) {
+			data->zone_hyst[ix] = dme1737_read(client,
+						DME1737_REG_ZONE_HYST(ix));
+		}
+
+		/* Alarm registers */
+		data->alarms = dme1737_read(client,
+						DME1737_REG_ALARM1);
+		/* Bit 7 tells us if the other alarm registers are non-zero and
+		 * therefore also need to be read */
+		if (data->alarms & 0x80) {
+			data->alarms |= dme1737_read(client,
+						DME1737_REG_ALARM2) << 8;
+			data->alarms |= dme1737_read(client,
+						DME1737_REG_ALARM3) << 16;
+		}
+
+		data->last_update = jiffies;
+		data->valid = 1;
+	}
+
+	mutex_unlock(&data->update_lock);
+
+	return data;
+}
+
+/* ---------------------------------------------------------------------
+ * Voltage sysfs attributes
+ * ix = [0-5]
+ * --------------------------------------------------------------------- */
+
+#define SYS_IN_INPUT	0
+#define SYS_IN_MIN	1
+#define SYS_IN_MAX	2
+#define SYS_IN_ALARM	3
+
+static ssize_t show_in(struct device *dev, struct device_attribute *attr,
+		       char *buf)
+{
+	struct dme1737_data *data = dme1737_update_device(dev);
+	struct sensor_device_attribute_2
+		*sensor_attr_2 = to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	int res;
+
+	switch (fn) {
+	case SYS_IN_INPUT:
+		res = IN_FROM_REG(data->in[ix], ix, 16);
+		break;
+	case SYS_IN_MIN:
+		res = IN_FROM_REG(data->in_min[ix], ix, 8);
+		break;
+	case SYS_IN_MAX:
+		res = IN_FROM_REG(data->in_max[ix], ix, 8);
+		break;
+	case SYS_IN_ALARM:
+		res = (data->alarms >> DME1737_BIT_ALARM_IN[ix]) & 0x01;
+		break;
+	default:
+		res = 0;
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+
+	return sprintf(buf, "%d\n", res);
+}
+
+static ssize_t set_in(struct device *dev, struct device_attribute *attr,
+		      const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct dme1737_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2
+		*sensor_attr_2 = to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	long val = simple_strtol(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	switch (fn) {
+	case SYS_IN_MIN:
+		data->in_min[ix] = IN_TO_REG(val, ix);
+		dme1737_write(client, DME1737_REG_IN_MIN(ix),
+			      data->in_min[ix]);
+		break;
+	case SYS_IN_MAX:
+		data->in_max[ix] = IN_TO_REG(val, ix);
+		dme1737_write(client, DME1737_REG_IN_MAX(ix),
+			      data->in_max[ix]);
+		break;
+	default:
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+/* ---------------------------------------------------------------------
+ * Temperature sysfs attributes
+ * ix = [0-2]
+ * --------------------------------------------------------------------- */
+
+#define SYS_TEMP_INPUT			0
+#define SYS_TEMP_MIN			1
+#define SYS_TEMP_MAX			2
+#define SYS_TEMP_OFFSET			3
+#define SYS_TEMP_ALARM			4
+#define SYS_TEMP_FAULT			5
+
+static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
+			 char *buf)
+{
+	struct dme1737_data *data = dme1737_update_device(dev);
+	struct sensor_device_attribute_2
+		*sensor_attr_2 = to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	int res;
+
+	switch (fn) {
+	case SYS_TEMP_INPUT:
+		res = TEMP_FROM_REG(data->temp[ix], 16);
+		break;
+	case SYS_TEMP_MIN:
+		res = TEMP_FROM_REG(data->temp_min[ix], 8);
+		break;
+	case SYS_TEMP_MAX:
+		res = TEMP_FROM_REG(data->temp_max[ix], 8);
+		break;
+	case SYS_TEMP_OFFSET:
+		res = TEMP_FROM_REG(data->temp_offset[ix], 8);
+		break;
+	case SYS_TEMP_ALARM:
+		res = (data->alarms >> DME1737_BIT_ALARM_TEMP[ix]) & 0x01;
+		break;
+	case SYS_TEMP_FAULT:
+		res = (data->temp[ix] == 0x0800);
+		break;
+	default:
+		res = 0;
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+
+	return sprintf(buf, "%d\n", res);
+}
+
+static ssize_t set_temp(struct device *dev, struct device_attribute *attr,
+			const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct dme1737_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2
+		*sensor_attr_2 = to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	long val = simple_strtol(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	switch (fn) {
+	case SYS_TEMP_MIN:
+		data->temp_min[ix] = TEMP_TO_REG(val);
+		dme1737_write(client, DME1737_REG_TEMP_MIN(ix),
+			      data->temp_min[ix]);
+		break;
+	case SYS_TEMP_MAX:
+		data->temp_max[ix] = TEMP_TO_REG(val);
+		dme1737_write(client, DME1737_REG_TEMP_MAX(ix),
+			      data->temp_max[ix]);
+		break;
+	case SYS_TEMP_OFFSET:
+		data->temp_offset[ix] = TEMP_TO_REG(val);
+		dme1737_write(client, DME1737_REG_TEMP_OFFSET(ix),
+			      data->temp_offset[ix]);
+		break;
+	default:
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+/* ---------------------------------------------------------------------
+ * Zone sysfs attributes
+ * ix = [0-2]
+ * --------------------------------------------------------------------- */
+
+#define SYS_ZONE_AUTO_CHANNELS_TEMP	0
+#define SYS_ZONE_AUTO_POINT1_TEMP_HYST	1
+#define SYS_ZONE_AUTO_POINT1_TEMP	2
+#define SYS_ZONE_AUTO_POINT2_TEMP	3
+#define SYS_ZONE_AUTO_POINT3_TEMP	4
+
+static ssize_t show_zone(struct device *dev, struct device_attribute *attr,
+			 char *buf)
+{
+	struct dme1737_data *data = dme1737_update_device(dev);
+	struct sensor_device_attribute_2
+		*sensor_attr_2 = to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	int res;
+
+	switch (fn) {
+	case SYS_ZONE_AUTO_CHANNELS_TEMP:
+		/* check config2 for non-standard temp-to-zone mapping */
+		if ((ix == 1) && (data->config2 & 0x02)) {
+			res = 4;
+		} else {
+			res = 1 << ix;
+		}
+		break;
+	case SYS_ZONE_AUTO_POINT1_TEMP_HYST:
+		res = TEMP_FROM_REG(data->zone_low[ix], 8) -
+		      TEMP_HYST_FROM_REG(data->zone_hyst[ix == 2], ix);
+		break;
+	case SYS_ZONE_AUTO_POINT1_TEMP:
+		res = TEMP_FROM_REG(data->zone_low[ix], 8);
+		break;
+	case SYS_ZONE_AUTO_POINT2_TEMP:
+		/* pwm_freq holds the temp range bits in the upper nibble */
+		res = TEMP_FROM_REG(data->zone_low[ix], 8) +
+		      TEMP_RANGE_FROM_REG(data->pwm_freq[ix]);
+		break;
+	case SYS_ZONE_AUTO_POINT3_TEMP:
+		res = TEMP_FROM_REG(data->zone_abs[ix], 8);
+		break;
+	default:
+		res = 0;
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+
+	return sprintf(buf, "%d\n", res);
+}
+
+static ssize_t set_zone(struct device *dev, struct device_attribute *attr,
+			const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct dme1737_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2
+		*sensor_attr_2 = to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	long val = simple_strtol(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	switch (fn) {
+	case SYS_ZONE_AUTO_POINT1_TEMP_HYST:
+		/* Refresh the cache */
+		data->zone_low[ix] = dme1737_read(client,
+						  DME1737_REG_ZONE_LOW(ix));
+		/* Modify the temp hyst value */
+		data->zone_hyst[ix == 2] = TEMP_HYST_TO_REG(
+					TEMP_FROM_REG(data->zone_low[ix], 8) -
+					val, ix, dme1737_read(client,
+					DME1737_REG_ZONE_HYST(ix == 2)));
+		dme1737_write(client, DME1737_REG_ZONE_HYST(ix == 2),
+			      data->zone_hyst[ix == 2]);
+		break;
+	case SYS_ZONE_AUTO_POINT1_TEMP:
+		data->zone_low[ix] = TEMP_TO_REG(val);
+		dme1737_write(client, DME1737_REG_ZONE_LOW(ix),
+			      data->zone_low[ix]);
+		break;
+	case SYS_ZONE_AUTO_POINT2_TEMP:
+		/* Refresh the cache */
+		data->zone_low[ix] = dme1737_read(client,
+						  DME1737_REG_ZONE_LOW(ix));
+		/* Modify the temp range value (which is stored in the upper
+		 * nibble of the pwm_freq register) */
+		data->pwm_freq[ix] = TEMP_RANGE_TO_REG(val -
+					TEMP_FROM_REG(data->zone_low[ix], 8),
+					dme1737_read(client,
+					DME1737_REG_PWM_FREQ(ix)));
+		dme1737_write(client, DME1737_REG_PWM_FREQ(ix),
+			      data->pwm_freq[ix]);
+		break;
+	case SYS_ZONE_AUTO_POINT3_TEMP:
+		data->zone_abs[ix] = TEMP_TO_REG(val);
+		dme1737_write(client, DME1737_REG_ZONE_ABS(ix),
+			      data->zone_abs[ix]);
+		break;
+	default:
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+/* ---------------------------------------------------------------------
+ * Fan sysfs attributes
+ * ix = [0-5]
+ * --------------------------------------------------------------------- */
+
+#define SYS_FAN_INPUT	0
+#define SYS_FAN_MIN	1
+#define SYS_FAN_MAX	2
+#define SYS_FAN_ALARM	3
+#define SYS_FAN_TYPE	4
+
+static ssize_t show_fan(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct dme1737_data *data = dme1737_update_device(dev);
+	struct sensor_device_attribute_2
+		*sensor_attr_2 = to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	int res;
+
+	switch (fn) {
+	case SYS_FAN_INPUT:
+		res = FAN_FROM_REG(data->fan[ix],
+				   ix < 4 ? 0 :
+				   FAN_TPC_FROM_REG(data->fan_opt[ix]));
+		break;
+	case SYS_FAN_MIN:
+		res = FAN_FROM_REG(data->fan_min[ix],
+				   ix < 4 ? 0 :
+				   FAN_TPC_FROM_REG(data->fan_opt[ix]));
+		break;
+	case SYS_FAN_MAX:
+		/* only valid for fan[5-6] */
+		res = FAN_MAX_FROM_REG(data->fan_max[ix - 4]);
+		break;
+	case SYS_FAN_ALARM:
+		res = (data->alarms >> DME1737_BIT_ALARM_FAN[ix]) & 0x01;
+		break;
+	case SYS_FAN_TYPE:
+		/* only valid for fan[1-4] */
+		res = FAN_TYPE_FROM_REG(data->fan_opt[ix]);
+		break;
+	default:
+		res = 0;
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+
+	return sprintf(buf, "%d\n", res);
+}
+
+static ssize_t set_fan(struct device *dev, struct device_attribute *attr,
+		       const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct dme1737_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2
+		*sensor_attr_2 = to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	long val = simple_strtol(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	switch (fn) {
+	case SYS_FAN_MIN:
+		if (ix < 4) {
+			data->fan_min[ix] = FAN_TO_REG(val, 0);
+		} else {
+			/* Refresh the cache */
+			data->fan_opt[ix] = dme1737_read(client,
+						DME1737_REG_FAN_OPT(ix));
+			/* Modify the fan min value */
+			data->fan_min[ix] = FAN_TO_REG(val,
+					FAN_TPC_FROM_REG(data->fan_opt[ix]));
+		}
+		dme1737_write(client, DME1737_REG_FAN_MIN(ix),
+			      data->fan_min[ix] & 0xff);
+		dme1737_write(client, DME1737_REG_FAN_MIN(ix) + 1,
+			      data->fan_min[ix] >> 8);
+		break;
+	case SYS_FAN_MAX:
+		/* Only valid for fan[5-6] */
+		data->fan_max[ix - 4] = FAN_MAX_TO_REG(val);
+		dme1737_write(client, DME1737_REG_FAN_MAX(ix),
+			      data->fan_max[ix - 4]);
+		break;
+	case SYS_FAN_TYPE:
+		/* Only valid for fan[1-4] */
+		if (!(val == 1 || val == 2 || val == 4)) {
+			count = -EINVAL;
+			dev_warn(&client->dev, "Fan type value %ld not "
+				 "supported. Choose one of 1, 2, or 4.\n",
+				 val);
+			goto exit;
+		}
+		data->fan_opt[ix] = FAN_TYPE_TO_REG(val, dme1737_read(client,
+					DME1737_REG_FAN_OPT(ix)));
+		dme1737_write(client, DME1737_REG_FAN_OPT(ix),
+			      data->fan_opt[ix]);
+		break;
+	default:
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+exit:
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+/* ---------------------------------------------------------------------
+ * PWM sysfs attributes
+ * ix = [0-4]
+ * --------------------------------------------------------------------- */
+
+#define SYS_PWM				0
+#define SYS_PWM_FREQ			1
+#define SYS_PWM_ENABLE			2
+#define SYS_PWM_RAMP_RATE		3
+#define SYS_PWM_AUTO_CHANNELS_ZONE	4
+#define SYS_PWM_AUTO_PWM_MIN		5
+#define SYS_PWM_AUTO_POINT1_PWM		6
+#define SYS_PWM_AUTO_POINT2_PWM		7
+
+static ssize_t show_pwm(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct dme1737_data *data = dme1737_update_device(dev);
+	struct sensor_device_attribute_2
+		*sensor_attr_2 = to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	int res;
+
+	switch (fn) {
+	case SYS_PWM:
+		if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 0) {
+			res = 255;
+		} else {
+			res = data->pwm[ix];
+		}
+		break;
+	case SYS_PWM_FREQ:
+		res = PWM_FREQ_FROM_REG(data->pwm_freq[ix]);
+		break;
+	case SYS_PWM_ENABLE:
+		if (ix > 3) {
+			res = 1; /* pwm[5-6] hard-wired to manual mode */
+		} else {
+			res = PWM_EN_FROM_REG(data->pwm_config[ix]);
+		}
+		break;
+	case SYS_PWM_RAMP_RATE:
+		/* Only valid for pwm[1-3] */
+		res = PWM_RR_FROM_REG(data->pwm_rr[ix > 0], ix);
+		break;
+	case SYS_PWM_AUTO_CHANNELS_ZONE:
+		/* Only valid for pwm[1-3] */
+		if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) {
+			res = PWM_ACZ_FROM_REG(data->pwm_config[ix]);
+		} else {
+			res = data->pwm_acz[ix];
+		}
+		break;
+	case SYS_PWM_AUTO_PWM_MIN:
+		/* Only valid for pwm[1-3] */
+		if (PWM_OFF_FROM_REG(data->pwm_rr[0], ix)) {
+			res = data->pwm_min[ix];
+		} else {
+			res = 0;
+		}
+		break;
+	case SYS_PWM_AUTO_POINT1_PWM:
+		/* Only valid for pwm[1-3] */
+		res = data->pwm_min[ix];
+		break;
+	case SYS_PWM_AUTO_POINT2_PWM:
+		/* Only valid for pwm[1-3] */
+		res = 255; /* hard-wired */
+		break;
+	default:
+		res = 0;
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+
+	return sprintf(buf, "%d\n", res);
+}
+
+static struct attribute *dme1737_attr_pwm[];
+static void dme1737_chmod_file(struct i2c_client*, struct attribute*, mode_t);
+
+static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
+		       const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct dme1737_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2
+		*sensor_attr_2 = to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	long val = simple_strtol(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	switch (fn) {
+	case SYS_PWM:
+		data->pwm[ix] = SENSORS_LIMIT(val, 0, 255);
+		dme1737_write(client, DME1737_REG_PWM(ix), data->pwm[ix]);
+		break;
+	case SYS_PWM_FREQ:
+		data->pwm_freq[ix] = PWM_FREQ_TO_REG(val, dme1737_read(client,
+						DME1737_REG_PWM_FREQ(ix)));
+		dme1737_write(client, DME1737_REG_PWM_FREQ(ix),
+			      data->pwm_freq[ix]);
+		break;
+	case SYS_PWM_ENABLE:
+		/* Only valid for pwm[1-3] */
+		if (val < 0 || val > 2) {
+			count = -EINVAL;
+			dev_warn(&client->dev, "PWM enable %ld not "
+				 "supported. Choose one of 0, 1, or 2.\n",
+				 val);
+			goto exit;
+		}
+		/* Refresh the cache */
+		data->pwm_config[ix] = dme1737_read(client,
+						DME1737_REG_PWM_CONFIG(ix));
+		if (val == PWM_EN_FROM_REG(data->pwm_config[ix])) {
+			/* Bail out if no change */
+			goto exit;
+		}
+		/* Do some housekeeping if we are currently in auto mode */
+		if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) {
+			/* Save the current zone channel assignment */
+			data->pwm_acz[ix] = PWM_ACZ_FROM_REG(
+							data->pwm_config[ix]);
+			/* Save the current ramp rate state and disable it */
+			data->pwm_rr[ix > 0] = dme1737_read(client,
+						DME1737_REG_PWM_RR(ix > 0));
+			data->pwm_rr_en &= ~(1 << ix);
+			if (PWM_RR_EN_FROM_REG(data->pwm_rr[ix > 0], ix)) {
+				data->pwm_rr_en |= (1 << ix);
+				data->pwm_rr[ix > 0] = PWM_RR_EN_TO_REG(0, ix,
+							data->pwm_rr[ix > 0]);
+				dme1737_write(client,
+					      DME1737_REG_PWM_RR(ix > 0),
+					      data->pwm_rr[ix > 0]);
+			}
+		}
+		/* Set the new PWM mode */
+		switch (val) {
+		case 0:
+			/* Change permissions of pwm[ix] to read-only */
+			dme1737_chmod_file(client, dme1737_attr_pwm[ix],
+					   S_IRUGO);
+			/* Turn fan fully on */
+			data->pwm_config[ix] = PWM_EN_TO_REG(0,
+							data->pwm_config[ix]);
+			dme1737_write(client, DME1737_REG_PWM_CONFIG(ix),
+				      data->pwm_config[ix]);
+			break;
+		case 1:
+			/* Turn on manual mode */
+			data->pwm_config[ix] = PWM_EN_TO_REG(1,
+							data->pwm_config[ix]);
+			dme1737_write(client, DME1737_REG_PWM_CONFIG(ix),
+				      data->pwm_config[ix]);
+			/* Change permissions of pwm[ix] to read-writeable */
+			dme1737_chmod_file(client, dme1737_attr_pwm[ix],
+					   S_IRUGO | S_IWUSR);
+			break;
+		case 2:
+			/* Change permissions of pwm[ix] to read-only */
+			dme1737_chmod_file(client, dme1737_attr_pwm[ix],
+					   S_IRUGO);
+			/* Turn on auto mode using the saved zone channel
+			 * assignment */
+			data->pwm_config[ix] = PWM_ACZ_TO_REG(
+							data->pwm_acz[ix],
+							data->pwm_config[ix]);
+			dme1737_write(client, DME1737_REG_PWM_CONFIG(ix),
+				      data->pwm_config[ix]);
+			/* Enable PWM ramp rate if previously enabled */
+			if (data->pwm_rr_en & (1 << ix)) {
+				data->pwm_rr[ix > 0] = PWM_RR_EN_TO_REG(1, ix,
+						dme1737_read(client,
+						DME1737_REG_PWM_RR(ix > 0)));
+				dme1737_write(client,
+					      DME1737_REG_PWM_RR(ix > 0),
+					      data->pwm_rr[ix > 0]);
+			}
+			break;
+		}
+		break;
+	case SYS_PWM_RAMP_RATE:
+		/* Only valid for pwm[1-3] */
+		/* Refresh the cache */
+		data->pwm_config[ix] = dme1737_read(client,
+						DME1737_REG_PWM_CONFIG(ix));
+		data->pwm_rr[ix > 0] = dme1737_read(client,
+						DME1737_REG_PWM_RR(ix > 0));
+		/* Set the ramp rate value */
+		if (val > 0) {
+			data->pwm_rr[ix > 0] = PWM_RR_TO_REG(val, ix,
+							data->pwm_rr[ix > 0]);
+		}
+		/* Enable/disable the feature only if the associated PWM
+		 * output is in automatic mode. */
+		if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) {
+			data->pwm_rr[ix > 0] = PWM_RR_EN_TO_REG(val > 0, ix,
+							data->pwm_rr[ix > 0]);
+		}
+		dme1737_write(client, DME1737_REG_PWM_RR(ix > 0),
+			      data->pwm_rr[ix > 0]);
+		break;
+	case SYS_PWM_AUTO_CHANNELS_ZONE:
+		/* Only valid for pwm[1-3] */
+		if (!(val == 1 || val == 2 || val == 4 ||
+		      val == 6 || val == 7)) {
+			count = -EINVAL;
+			dev_warn(&client->dev, "PWM auto channels zone %ld "
+				 "not supported. Choose one of 1, 2, 4, 6, "
+				 "or 7.\n", val);
+			goto exit;
+		}
+		/* Refresh the cache */
+		data->pwm_config[ix] = dme1737_read(client,
+						DME1737_REG_PWM_CONFIG(ix));
+		if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) {
+			/* PWM is already in auto mode so update the temp
+			 * channel assignment */
+			data->pwm_config[ix] = PWM_ACZ_TO_REG(val,
+						data->pwm_config[ix]);
+			dme1737_write(client, DME1737_REG_PWM_CONFIG(ix),
+				      data->pwm_config[ix]);
+		} else {
+			/* PWM is not in auto mode so we save the temp
+			 * channel assignment for later use */
+			data->pwm_acz[ix] = val;
+		}
+		break;
+	case SYS_PWM_AUTO_PWM_MIN:
+		/* Only valid for pwm[1-3] */
+		/* Refresh the cache */
+		data->pwm_min[ix] = dme1737_read(client,
+						DME1737_REG_PWM_MIN(ix));
+		/* There are only 2 values supported for the auto_pwm_min
+		 * value: 0 or auto_point1_pwm. So if the temperature drops
+		 * below the auto_point1_temp_hyst value, the fan either turns
+		 * off or runs at auto_point1_pwm duty-cycle. */
+		if (val > ((data->pwm_min[ix] + 1) / 2)) {
+			data->pwm_rr[0] = PWM_OFF_TO_REG(1, ix,
+						dme1737_read(client,
+						DME1737_REG_PWM_RR(0)));
+
+		} else {
+			data->pwm_rr[0] = PWM_OFF_TO_REG(0, ix,
+						dme1737_read(client,
+						DME1737_REG_PWM_RR(0)));
+
+		}
+		dme1737_write(client, DME1737_REG_PWM_RR(0),
+			      data->pwm_rr[0]);
+		break;
+	case SYS_PWM_AUTO_POINT1_PWM:
+		/* Only valid for pwm[1-3] */
+		data->pwm_min[ix] = SENSORS_LIMIT(val, 0, 255);
+		dme1737_write(client, DME1737_REG_PWM_MIN(ix),
+			      data->pwm_min[ix]);
+		break;
+	default:
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+exit:
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+/* ---------------------------------------------------------------------
+ * Miscellaneous sysfs attributes
+ * --------------------------------------------------------------------- */
+
+static ssize_t show_vrm(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct dme1737_data *data = i2c_get_clientdata(client);
+
+	return sprintf(buf, "%d\n", data->vrm);
+}
+
+static ssize_t set_vrm(struct device *dev, struct device_attribute *attr,
+		       const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct dme1737_data *data = i2c_get_clientdata(client);
+	long val = simple_strtol(buf, NULL, 10);
+
+	data->vrm = val;
+	return count;
+}
+
+static ssize_t show_vid(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct dme1737_data *data = dme1737_update_device(dev);
+
+	return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm));
+}
+
+/* ---------------------------------------------------------------------
+ * Sysfs device attribute defines and structs
+ * --------------------------------------------------------------------- */
+
+/* Voltages 0-6 */
+
+#define SENSOR_DEVICE_ATTR_IN(ix) \
+static SENSOR_DEVICE_ATTR_2(in##ix##_input, S_IRUGO, \
+        show_in, NULL, SYS_IN_INPUT, ix); \
+static SENSOR_DEVICE_ATTR_2(in##ix##_min, S_IRUGO | S_IWUSR, \
+        show_in, set_in, SYS_IN_MIN, ix); \
+static SENSOR_DEVICE_ATTR_2(in##ix##_max, S_IRUGO | S_IWUSR, \
+        show_in, set_in, SYS_IN_MAX, ix); \
+static SENSOR_DEVICE_ATTR_2(in##ix##_alarm, S_IRUGO, \
+        show_in, NULL, SYS_IN_ALARM, ix)
+
+SENSOR_DEVICE_ATTR_IN(0);
+SENSOR_DEVICE_ATTR_IN(1);
+SENSOR_DEVICE_ATTR_IN(2);
+SENSOR_DEVICE_ATTR_IN(3);
+SENSOR_DEVICE_ATTR_IN(4);
+SENSOR_DEVICE_ATTR_IN(5);
+SENSOR_DEVICE_ATTR_IN(6);
+
+/* Temperatures 1-3 */
+
+#define SENSOR_DEVICE_ATTR_TEMP(ix) \
+static SENSOR_DEVICE_ATTR_2(temp##ix##_input, S_IRUGO, \
+        show_temp, NULL, SYS_TEMP_INPUT, ix-1); \
+static SENSOR_DEVICE_ATTR_2(temp##ix##_min, S_IRUGO | S_IWUSR, \
+        show_temp, set_temp, SYS_TEMP_MIN, ix-1); \
+static SENSOR_DEVICE_ATTR_2(temp##ix##_max, S_IRUGO | S_IWUSR, \
+        show_temp, set_temp, SYS_TEMP_MAX, ix-1); \
+static SENSOR_DEVICE_ATTR_2(temp##ix##_offset, S_IRUGO, \
+        show_temp, set_temp, SYS_TEMP_OFFSET, ix-1); \
+static SENSOR_DEVICE_ATTR_2(temp##ix##_alarm, S_IRUGO, \
+        show_temp, NULL, SYS_TEMP_ALARM, ix-1); \
+static SENSOR_DEVICE_ATTR_2(temp##ix##_fault, S_IRUGO, \
+        show_temp, NULL, SYS_TEMP_FAULT, ix-1)
+
+SENSOR_DEVICE_ATTR_TEMP(1);
+SENSOR_DEVICE_ATTR_TEMP(2);
+SENSOR_DEVICE_ATTR_TEMP(3);
+
+/* Zones 1-3 */
+
+#define SENSOR_DEVICE_ATTR_ZONE(ix) \
+static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_channels_temp, S_IRUGO, \
+        show_zone, NULL, SYS_ZONE_AUTO_CHANNELS_TEMP, ix-1); \
+static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_point1_temp_hyst, S_IRUGO, \
+        show_zone, set_zone, SYS_ZONE_AUTO_POINT1_TEMP_HYST, ix-1); \
+static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_point1_temp, S_IRUGO, \
+        show_zone, set_zone, SYS_ZONE_AUTO_POINT1_TEMP, ix-1); \
+static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_point2_temp, S_IRUGO, \
+        show_zone, set_zone, SYS_ZONE_AUTO_POINT2_TEMP, ix-1); \
+static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_point3_temp, S_IRUGO, \
+        show_zone, set_zone, SYS_ZONE_AUTO_POINT3_TEMP, ix-1)
+
+SENSOR_DEVICE_ATTR_ZONE(1);
+SENSOR_DEVICE_ATTR_ZONE(2);
+SENSOR_DEVICE_ATTR_ZONE(3);
+
+/* Fans 1-4 */
+
+#define SENSOR_DEVICE_ATTR_FAN_1TO4(ix) \
+static SENSOR_DEVICE_ATTR_2(fan##ix##_input, S_IRUGO, \
+        show_fan, NULL, SYS_FAN_INPUT, ix-1); \
+static SENSOR_DEVICE_ATTR_2(fan##ix##_min, S_IRUGO | S_IWUSR, \
+        show_fan, set_fan, SYS_FAN_MIN, ix-1); \
+static SENSOR_DEVICE_ATTR_2(fan##ix##_alarm, S_IRUGO, \
+        show_fan, NULL, SYS_FAN_ALARM, ix-1); \
+static SENSOR_DEVICE_ATTR_2(fan##ix##_type, S_IRUGO | S_IWUSR, \
+        show_fan, set_fan, SYS_FAN_TYPE, ix-1)
+
+SENSOR_DEVICE_ATTR_FAN_1TO4(1);
+SENSOR_DEVICE_ATTR_FAN_1TO4(2);
+SENSOR_DEVICE_ATTR_FAN_1TO4(3);
+SENSOR_DEVICE_ATTR_FAN_1TO4(4);
+
+/* Fans 5-6 */
+
+#define SENSOR_DEVICE_ATTR_FAN_5TO6(ix) \
+static SENSOR_DEVICE_ATTR_2(fan##ix##_input, S_IRUGO, \
+        show_fan, NULL, SYS_FAN_INPUT, ix-1); \
+static SENSOR_DEVICE_ATTR_2(fan##ix##_min, S_IRUGO | S_IWUSR, \
+        show_fan, set_fan, SYS_FAN_MIN, ix-1); \
+static SENSOR_DEVICE_ATTR_2(fan##ix##_alarm, S_IRUGO, \
+        show_fan, NULL, SYS_FAN_ALARM, ix-1); \
+static SENSOR_DEVICE_ATTR_2(fan##ix##_max, S_IRUGO | S_IWUSR, \
+        show_fan, set_fan, SYS_FAN_MAX, ix-1)
+
+SENSOR_DEVICE_ATTR_FAN_5TO6(5);
+SENSOR_DEVICE_ATTR_FAN_5TO6(6);
+
+/* PWMs 1-3 */
+
+#define SENSOR_DEVICE_ATTR_PWM_1TO3(ix) \
+static SENSOR_DEVICE_ATTR_2(pwm##ix, S_IRUGO, \
+        show_pwm, set_pwm, SYS_PWM, ix-1); \
+static SENSOR_DEVICE_ATTR_2(pwm##ix##_freq, S_IRUGO, \
+        show_pwm, set_pwm, SYS_PWM_FREQ, ix-1); \
+static SENSOR_DEVICE_ATTR_2(pwm##ix##_enable, S_IRUGO, \
+        show_pwm, set_pwm, SYS_PWM_ENABLE, ix-1); \
+static SENSOR_DEVICE_ATTR_2(pwm##ix##_ramp_rate, S_IRUGO, \
+        show_pwm, set_pwm, SYS_PWM_RAMP_RATE, ix-1); \
+static SENSOR_DEVICE_ATTR_2(pwm##ix##_auto_channels_zone, S_IRUGO, \
+        show_pwm, set_pwm, SYS_PWM_AUTO_CHANNELS_ZONE, ix-1); \
+static SENSOR_DEVICE_ATTR_2(pwm##ix##_auto_pwm_min, S_IRUGO, \
+        show_pwm, set_pwm, SYS_PWM_AUTO_PWM_MIN, ix-1); \
+static SENSOR_DEVICE_ATTR_2(pwm##ix##_auto_point1_pwm, S_IRUGO, \
+        show_pwm, set_pwm, SYS_PWM_AUTO_POINT1_PWM, ix-1); \
+static SENSOR_DEVICE_ATTR_2(pwm##ix##_auto_point2_pwm, S_IRUGO, \
+        show_pwm, NULL, SYS_PWM_AUTO_POINT2_PWM, ix-1)
+
+SENSOR_DEVICE_ATTR_PWM_1TO3(1);
+SENSOR_DEVICE_ATTR_PWM_1TO3(2);
+SENSOR_DEVICE_ATTR_PWM_1TO3(3);
+
+/* PWMs 5-6 */
+
+#define SENSOR_DEVICE_ATTR_PWM_5TO6(ix) \
+static SENSOR_DEVICE_ATTR_2(pwm##ix, S_IRUGO | S_IWUSR, \
+        show_pwm, set_pwm, SYS_PWM, ix-1); \
+static SENSOR_DEVICE_ATTR_2(pwm##ix##_freq, S_IRUGO | S_IWUSR, \
+        show_pwm, set_pwm, SYS_PWM_FREQ, ix-1); \
+static SENSOR_DEVICE_ATTR_2(pwm##ix##_enable, S_IRUGO, \
+        show_pwm, NULL, SYS_PWM_ENABLE, ix-1)
+
+SENSOR_DEVICE_ATTR_PWM_5TO6(5);
+SENSOR_DEVICE_ATTR_PWM_5TO6(6);
+
+/* Misc */
+
+static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm, set_vrm);
+static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid, NULL);
+
+#define SENSOR_DEV_ATTR_IN(ix) \
+&sensor_dev_attr_in##ix##_input.dev_attr.attr, \
+&sensor_dev_attr_in##ix##_min.dev_attr.attr, \
+&sensor_dev_attr_in##ix##_max.dev_attr.attr, \
+&sensor_dev_attr_in##ix##_alarm.dev_attr.attr
+
+/* These attributes are read-writeable only if the chip is *not* locked */
+#define SENSOR_DEV_ATTR_TEMP_LOCK(ix) \
+&sensor_dev_attr_temp##ix##_offset.dev_attr.attr
+
+#define SENSOR_DEV_ATTR_TEMP(ix) \
+SENSOR_DEV_ATTR_TEMP_LOCK(ix), \
+&sensor_dev_attr_temp##ix##_input.dev_attr.attr, \
+&sensor_dev_attr_temp##ix##_min.dev_attr.attr, \
+&sensor_dev_attr_temp##ix##_max.dev_attr.attr, \
+&sensor_dev_attr_temp##ix##_alarm.dev_attr.attr, \
+&sensor_dev_attr_temp##ix##_fault.dev_attr.attr
+
+/* These attributes are read-writeable only if the chip is *not* locked */
+#define SENSOR_DEV_ATTR_ZONE_LOCK(ix) \
+&sensor_dev_attr_zone##ix##_auto_point1_temp_hyst.dev_attr.attr, \
+&sensor_dev_attr_zone##ix##_auto_point1_temp.dev_attr.attr, \
+&sensor_dev_attr_zone##ix##_auto_point2_temp.dev_attr.attr, \
+&sensor_dev_attr_zone##ix##_auto_point3_temp.dev_attr.attr
+
+#define SENSOR_DEV_ATTR_ZONE(ix) \
+SENSOR_DEV_ATTR_ZONE_LOCK(ix), \
+&sensor_dev_attr_zone##ix##_auto_channels_temp.dev_attr.attr
+
+#define SENSOR_DEV_ATTR_FAN_1TO4(ix) \
+&sensor_dev_attr_fan##ix##_input.dev_attr.attr, \
+&sensor_dev_attr_fan##ix##_min.dev_attr.attr, \
+&sensor_dev_attr_fan##ix##_alarm.dev_attr.attr, \
+&sensor_dev_attr_fan##ix##_type.dev_attr.attr
+
+#define SENSOR_DEV_ATTR_FAN_5TO6(ix) \
+&sensor_dev_attr_fan##ix##_input.dev_attr.attr, \
+&sensor_dev_attr_fan##ix##_min.dev_attr.attr, \
+&sensor_dev_attr_fan##ix##_alarm.dev_attr.attr, \
+&sensor_dev_attr_fan##ix##_max.dev_attr.attr
+
+/* These attributes are read-writeable only if the chip is *not* locked */
+#define SENSOR_DEV_ATTR_PWM_1TO3_LOCK(ix) \
+&sensor_dev_attr_pwm##ix##_freq.dev_attr.attr, \
+&sensor_dev_attr_pwm##ix##_enable.dev_attr.attr, \
+&sensor_dev_attr_pwm##ix##_ramp_rate.dev_attr.attr, \
+&sensor_dev_attr_pwm##ix##_auto_channels_zone.dev_attr.attr, \
+&sensor_dev_attr_pwm##ix##_auto_pwm_min.dev_attr.attr, \
+&sensor_dev_attr_pwm##ix##_auto_point1_pwm.dev_attr.attr
+
+#define SENSOR_DEV_ATTR_PWM_1TO3(ix) \
+SENSOR_DEV_ATTR_PWM_1TO3_LOCK(ix), \
+&sensor_dev_attr_pwm##ix.dev_attr.attr, \
+&sensor_dev_attr_pwm##ix##_auto_point2_pwm.dev_attr.attr
+
+/* These attributes are read-writeable only if the chip is *not* locked */
+#define SENSOR_DEV_ATTR_PWM_5TO6_LOCK(ix) \
+&sensor_dev_attr_pwm##ix.dev_attr.attr, \
+&sensor_dev_attr_pwm##ix##_freq.dev_attr.attr
+
+#define SENSOR_DEV_ATTR_PWM_5TO6(ix) \
+SENSOR_DEV_ATTR_PWM_5TO6_LOCK(ix), \
+&sensor_dev_attr_pwm##ix##_enable.dev_attr.attr
+
+/* This struct holds all the attributes that are always present and need to be
+ * created unconditionally. The attributes that need modification of their
+ * permissions are created read-only and write permissions are added or removed
+ * on the fly when required */
+static struct attribute *dme1737_attr[] ={
+        /* Voltages */
+        SENSOR_DEV_ATTR_IN(0),
+        SENSOR_DEV_ATTR_IN(1),
+        SENSOR_DEV_ATTR_IN(2),
+        SENSOR_DEV_ATTR_IN(3),
+        SENSOR_DEV_ATTR_IN(4),
+        SENSOR_DEV_ATTR_IN(5),
+        SENSOR_DEV_ATTR_IN(6),
+        /* Temperatures */
+        SENSOR_DEV_ATTR_TEMP(1),
+        SENSOR_DEV_ATTR_TEMP(2),
+        SENSOR_DEV_ATTR_TEMP(3),
+        /* Zones */
+        SENSOR_DEV_ATTR_ZONE(1),
+        SENSOR_DEV_ATTR_ZONE(2),
+        SENSOR_DEV_ATTR_ZONE(3),
+        /* Misc */
+        &dev_attr_vrm.attr,
+        &dev_attr_cpu0_vid.attr,
+	NULL
+};
+
+static const struct attribute_group dme1737_group = {
+        .attrs = dme1737_attr,
+};
+
+/* The following structs hold the PWM attributes, some of which are optional.
+ * Their creation depends on the chip configuration which is determined during
+ * module load. */
+static struct attribute *dme1737_attr_pwm1[] = {
+        SENSOR_DEV_ATTR_PWM_1TO3(1),
+	NULL
+};
+static struct attribute *dme1737_attr_pwm2[] = {
+        SENSOR_DEV_ATTR_PWM_1TO3(2),
+	NULL
+};
+static struct attribute *dme1737_attr_pwm3[] = {
+        SENSOR_DEV_ATTR_PWM_1TO3(3),
+	NULL
+};
+static struct attribute *dme1737_attr_pwm5[] = {
+        SENSOR_DEV_ATTR_PWM_5TO6(5),
+	NULL
+};
+static struct attribute *dme1737_attr_pwm6[] = {
+        SENSOR_DEV_ATTR_PWM_5TO6(6),
+	NULL
+};
+
+static const struct attribute_group dme1737_pwm_group[] = {
+	{ .attrs = dme1737_attr_pwm1 },
+	{ .attrs = dme1737_attr_pwm2 },
+	{ .attrs = dme1737_attr_pwm3 },
+	{ .attrs = NULL },
+	{ .attrs = dme1737_attr_pwm5 },
+	{ .attrs = dme1737_attr_pwm6 },
+};
+
+/* The following structs hold the fan attributes, some of which are optional.
+ * Their creation depends on the chip configuration which is determined during
+ * module load. */
+static struct attribute *dme1737_attr_fan1[] = {
+        SENSOR_DEV_ATTR_FAN_1TO4(1),
+	NULL
+};
+static struct attribute *dme1737_attr_fan2[] = {
+        SENSOR_DEV_ATTR_FAN_1TO4(2),
+	NULL
+};
+static struct attribute *dme1737_attr_fan3[] = {
+        SENSOR_DEV_ATTR_FAN_1TO4(3),
+	NULL
+};
+static struct attribute *dme1737_attr_fan4[] = {
+        SENSOR_DEV_ATTR_FAN_1TO4(4),
+	NULL
+};
+static struct attribute *dme1737_attr_fan5[] = {
+        SENSOR_DEV_ATTR_FAN_5TO6(5),
+	NULL
+};
+static struct attribute *dme1737_attr_fan6[] = {
+        SENSOR_DEV_ATTR_FAN_5TO6(6),
+	NULL
+};
+
+static const struct attribute_group dme1737_fan_group[] = {
+	{ .attrs = dme1737_attr_fan1 },
+	{ .attrs = dme1737_attr_fan2 },
+	{ .attrs = dme1737_attr_fan3 },
+	{ .attrs = dme1737_attr_fan4 },
+	{ .attrs = dme1737_attr_fan5 },
+	{ .attrs = dme1737_attr_fan6 },
+};
+
+/* The permissions of all of the following attributes are changed to read-
+ * writeable if the chip is *not* locked. Otherwise they stay read-only. */
+static struct attribute *dme1737_attr_lock[] = {
+	/* Temperatures */
+	SENSOR_DEV_ATTR_TEMP_LOCK(1),
+	SENSOR_DEV_ATTR_TEMP_LOCK(2),
+	SENSOR_DEV_ATTR_TEMP_LOCK(3),
+	/* Zones */
+	SENSOR_DEV_ATTR_ZONE_LOCK(1),
+	SENSOR_DEV_ATTR_ZONE_LOCK(2),
+	SENSOR_DEV_ATTR_ZONE_LOCK(3),
+	NULL
+};
+
+static const struct attribute_group dme1737_lock_group = {
+	.attrs = dme1737_attr_lock,
+};
+
+/* The permissions of the following PWM attributes are changed to read-
+ * writeable if the chip is *not* locked and the respective PWM is available.
+ * Otherwise they stay read-only. */
+static struct attribute *dme1737_attr_pwm1_lock[] = {
+        SENSOR_DEV_ATTR_PWM_1TO3_LOCK(1),
+	NULL
+};
+static struct attribute *dme1737_attr_pwm2_lock[] = {
+        SENSOR_DEV_ATTR_PWM_1TO3_LOCK(2),
+	NULL
+};
+static struct attribute *dme1737_attr_pwm3_lock[] = {
+        SENSOR_DEV_ATTR_PWM_1TO3_LOCK(3),
+	NULL
+};
+static struct attribute *dme1737_attr_pwm5_lock[] = {
+        SENSOR_DEV_ATTR_PWM_5TO6_LOCK(5),
+	NULL
+};
+static struct attribute *dme1737_attr_pwm6_lock[] = {
+        SENSOR_DEV_ATTR_PWM_5TO6_LOCK(6),
+	NULL
+};
+
+static const struct attribute_group dme1737_pwm_lock_group[] = {
+	{ .attrs = dme1737_attr_pwm1_lock },
+	{ .attrs = dme1737_attr_pwm2_lock },
+	{ .attrs = dme1737_attr_pwm3_lock },
+	{ .attrs = NULL },
+	{ .attrs = dme1737_attr_pwm5_lock },
+	{ .attrs = dme1737_attr_pwm6_lock },
+};
+
+/* Pwm[1-3] are read-writeable if the associated pwm is in manual mode and the
+ * chip is not locked. Otherwise they are read-only. */
+static struct attribute *dme1737_attr_pwm[] = {
+	&sensor_dev_attr_pwm1.dev_attr.attr,
+	&sensor_dev_attr_pwm2.dev_attr.attr,
+	&sensor_dev_attr_pwm3.dev_attr.attr,
+};
+
+/* ---------------------------------------------------------------------
+ * Super-IO functions
+ * --------------------------------------------------------------------- */
+
+static inline int dme1737_sio_inb(int sio_cip, int reg)
+{
+	outb(reg, sio_cip);
+	return inb(sio_cip + 1);
+}
+
+static inline void dme1737_sio_outb(int sio_cip, int reg, int val)
+{
+	outb(reg, sio_cip);
+	outb(val, sio_cip + 1);
+}
+
+static int dme1737_sio_get_features(int sio_cip, struct i2c_client *client)
+{
+	struct dme1737_data *data = i2c_get_clientdata(client);
+	int err = 0, reg;
+	u16 addr;
+
+	/* Enter configuration mode */
+	outb(0x55, sio_cip);
+
+	/* Check device ID
+	 * The DME1737 can return either 0x78 or 0x77 as its device ID. */
+	reg = dme1737_sio_inb(sio_cip, 0x20);
+	if (!(reg == 0x77 || reg == 0x78)) {
+		err = -ENODEV;
+		goto exit;
+	}
+
+	/* Select logical device A (runtime registers) */
+	dme1737_sio_outb(sio_cip, 0x07, 0x0a);
+
+	/* Get the base address of the runtime registers */
+	if (!(addr = (dme1737_sio_inb(sio_cip, 0x60) << 8) |
+		      dme1737_sio_inb(sio_cip, 0x61))) {
+		err = -ENODEV;
+		goto exit;
+	}
+
+	/* Read the runtime registers to determine which optional features
+	 * are enabled and available. Bits [3:2] of registers 0x43-0x46 are set
+	 * to '10' if the respective feature is enabled. */
+	if ((inb(addr + 0x43) & 0x0c) == 0x08) { /* fan6 */
+		data->has_fan |= (1 << 5);
+	}
+	if ((inb(addr + 0x44) & 0x0c) == 0x08) { /* pwm6 */
+		data->has_pwm |= (1 << 5);
+	}
+	if ((inb(addr + 0x45) & 0x0c) == 0x08) { /* fan5 */
+		data->has_fan |= (1 << 4);
+	}
+	if ((inb(addr + 0x46) & 0x0c) == 0x08) { /* pwm5 */
+		data->has_pwm |= (1 << 4);
+	}
+
+exit:
+	/* Exit configuration mode */
+	outb(0xaa, sio_cip);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------
+ * Device detection, registration and initialization
+ * --------------------------------------------------------------------- */
+
+static struct i2c_driver dme1737_driver;
+
+static void dme1737_chmod_file(struct i2c_client *client,
+			       struct attribute *attr, mode_t mode)
+{
+	if (sysfs_chmod_file(&client->dev.kobj, attr, mode)) {
+		dev_warn(&client->dev, "Failed to change permissions of %s.\n",
+			 attr->name);
+	}
+}
+
+static void dme1737_chmod_group(struct i2c_client *client,
+				const struct attribute_group *group,
+				mode_t mode)
+{
+	struct attribute **attr;
+
+	for (attr = group->attrs; *attr; attr++) {
+		dme1737_chmod_file(client, *attr, mode);
+	}
+}
+
+static int dme1737_init_client(struct i2c_client *client)
+{
+	struct dme1737_data *data = i2c_get_clientdata(client);
+	int ix;
+	u8 reg;
+
+        data->config = dme1737_read(client, DME1737_REG_CONFIG);
+        /* Inform if part is not monitoring/started */
+        if (!(data->config & 0x01)) {
+                if (!force_start) {
+                        dev_err(&client->dev, "Device is not monitoring. "
+                                "Use the force_start load parameter to "
+                                "override.\n");
+                        return -EFAULT;
+                }
+
+                /* Force monitoring */
+                data->config |= 0x01;
+                dme1737_write(client, DME1737_REG_CONFIG, data->config);
+        }
+	/* Inform if part is not ready */
+	if (!(data->config & 0x04)) {
+		dev_err(&client->dev, "Device is not ready.\n");
+		return -EFAULT;
+	}
+
+	data->config2 = dme1737_read(client, DME1737_REG_CONFIG2);
+	/* Check if optional fan3 input is enabled */
+	if (data->config2 & 0x04) {
+		data->has_fan |= (1 << 2);
+	}
+
+	/* Fan4 and pwm3 are only available if the client's I2C address
+	 * is the default 0x2e. Otherwise the I/Os associated with these
+	 * functions are used for addr enable/select. */
+	if (client->addr == 0x2e) {
+		data->has_fan |= (1 << 3);
+		data->has_pwm |= (1 << 2);
+	}
+
+	/* Determine if the optional fan[5-6] and/or pwm[5-6] are enabled.
+	 * For this, we need to query the runtime registers through the
+	 * Super-IO LPC interface. Try both config ports 0x2e and 0x4e. */
+	if (dme1737_sio_get_features(0x2e, client) &&
+	    dme1737_sio_get_features(0x4e, client)) {
+		dev_warn(&client->dev, "Failed to query Super-IO for optional "
+			 "features.\n");
+	}
+
+	/* Fan1, fan2, pwm1, and pwm2 are always present */
+	data->has_fan |= 0x03;
+	data->has_pwm |= 0x03;
+
+	dev_info(&client->dev, "Optional features: pwm3=%s, pwm5=%s, pwm6=%s, "
+		 "fan3=%s, fan4=%s, fan5=%s, fan6=%s.\n",
+		 (data->has_pwm & (1 << 2)) ? "yes" : "no",
+		 (data->has_pwm & (1 << 4)) ? "yes" : "no",
+		 (data->has_pwm & (1 << 5)) ? "yes" : "no",
+		 (data->has_fan & (1 << 2)) ? "yes" : "no",
+		 (data->has_fan & (1 << 3)) ? "yes" : "no",
+		 (data->has_fan & (1 << 4)) ? "yes" : "no",
+		 (data->has_fan & (1 << 5)) ? "yes" : "no");
+
+	reg = dme1737_read(client, DME1737_REG_TACH_PWM);
+	/* Inform if fan-to-pwm mapping differs from the default */
+	if (reg != 0xa4) {
+		dev_warn(&client->dev, "Non-standard fan to pwm mapping: "
+			 "fan1->pwm%d, fan2->pwm%d, fan3->pwm%d, "
+			 "fan4->pwm%d. Please report to the driver "
+			 "maintainer.\n",
+			 (reg & 0x03) + 1, ((reg >> 2) & 0x03) + 1,
+			 ((reg >> 4) & 0x03) + 1, ((reg >> 6) & 0x03) + 1);
+	}
+
+	/* Switch pwm[1-3] to manual mode if they are currently disabled and
+	 * set the duty-cycles to 0% (which is identical to the PWMs being
+	 * disabled). */
+	if (!(data->config & 0x02)) {
+		for (ix = 0; ix < 3; ix++) {
+			data->pwm_config[ix] = dme1737_read(client,
+						DME1737_REG_PWM_CONFIG(ix));
+			if ((data->has_pwm & (1 << ix)) &&
+			    (PWM_EN_FROM_REG(data->pwm_config[ix]) == -1)) {
+				dev_info(&client->dev, "Switching pwm%d to "
+					 "manual mode.\n", ix + 1);
+				data->pwm_config[ix] = PWM_EN_TO_REG(1,
+							data->pwm_config[ix]);
+				dme1737_write(client, DME1737_REG_PWM(ix), 0);
+				dme1737_write(client,
+					      DME1737_REG_PWM_CONFIG(ix),
+					      data->pwm_config[ix]);
+			}
+		}
+	}
+
+	/* Initialize the default PWM auto channels zone (acz) assignments */
+	data->pwm_acz[0] = 1;	/* pwm1 -> zone1 */
+	data->pwm_acz[1] = 2;	/* pwm2 -> zone2 */
+	data->pwm_acz[2] = 4;	/* pwm3 -> zone3 */
+
+	/* Set VRM */
+	data->vrm = vid_which_vrm();
+
+	return 0;
+}
+
+static int dme1737_detect(struct i2c_adapter *adapter, int address,
+			  int kind)
+{
+	u8 company, verstep = 0;
+	struct i2c_client *client;
+	struct dme1737_data *data;
+	int ix, err = 0;
+	const char *name;
+
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
+		goto exit;
+	}
+
+	if (!(data = kzalloc(sizeof(struct dme1737_data), GFP_KERNEL))) {
+		err = -ENOMEM;
+		goto exit;
+	}
+
+	client = &data->client;
+	i2c_set_clientdata(client, data);
+	client->addr = address;
+	client->adapter = adapter;
+	client->driver = &dme1737_driver;
+
+	/* A negative kind means that the driver was loaded with no force
+	 * parameter (default), so we must identify the chip. */
+	if (kind < 0) {
+		company = dme1737_read(client, DME1737_REG_COMPANY);
+		verstep = dme1737_read(client, DME1737_REG_VERSTEP);
+
+		if (!((company == DME1737_COMPANY_SMSC) &&
+		      ((verstep & DME1737_VERSTEP_MASK) == DME1737_VERSTEP))) {
+			err = -ENODEV;
+			goto exit_kfree;
+		}
+	}
+
+	kind = dme1737;
+	name = "dme1737";
+
+	/* Fill in the remaining client fields and put it into the global
+	 * list */
+	strlcpy(client->name, name, I2C_NAME_SIZE);
+	mutex_init(&data->update_lock);
+
+	/* Tell the I2C layer a new client has arrived */
+	if ((err = i2c_attach_client(client))) {
+		goto exit_kfree;
+	}
+
+	/* Initialize the DME1737 chip */
+	if ((err = dme1737_init_client(client))) {
+		goto exit_detach;
+	}
+
+	/* Create standard sysfs attributes */
+	if ((err = sysfs_create_group(&client->dev.kobj, &dme1737_group))) {
+                goto exit_detach;
+	}
+
+	/* Create fan sysfs attributes */
+	for (ix = 0; ix < ARRAY_SIZE(dme1737_fan_group); ix++) {
+		if (data->has_fan & (1 << ix)) {
+			if ((err = sysfs_create_group(&client->dev.kobj,
+						&dme1737_fan_group[ix]))) {
+				goto exit_remove;
+			}
+		}
+	}
+
+	/* Create PWM sysfs attributes */
+	for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_group); ix++) {
+		if (data->has_pwm & (1 << ix)) {
+			if ((err = sysfs_create_group(&client->dev.kobj,
+						&dme1737_pwm_group[ix]))) {
+				goto exit_remove;
+			}
+		}
+	}
+
+	/* Inform if the device is locked. Otherwise change the permissions of
+	 * selected attributes from read-only to read-writeable. */
+	if (data->config & 0x02) {
+		dev_info(&client->dev, "Device is locked. Some attributes "
+			 "will be read-only.\n");
+	} else {
+		/* Change permissions of standard attributes */
+		dme1737_chmod_group(client, &dme1737_lock_group,
+				    S_IRUGO | S_IWUSR);
+
+		/* Change permissions of PWM attributes */
+		for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_lock_group); ix++) {
+			if (data->has_pwm & (1 << ix)) {
+				dme1737_chmod_group(client,
+						&dme1737_pwm_lock_group[ix],
+						S_IRUGO | S_IWUSR);
+			}
+		}
+
+		/* Change permissions of pwm[1-3] if in manual mode */
+		for (ix = 0; ix < 3; ix++) {
+			if ((data->has_pwm & (1 << ix)) &&
+			    (PWM_EN_FROM_REG(data->pwm_config[ix]) == 1)) {
+				dme1737_chmod_file(client,
+						   dme1737_attr_pwm[ix],
+						   S_IRUGO | S_IWUSR);
+			}
+		}
+	}
+
+	/* Register device */
+	data->class_dev = hwmon_device_register(&client->dev);
+	if (IS_ERR(data->class_dev)) {
+		err = PTR_ERR(data->class_dev);
+		goto exit_remove;
+	}
+
+	dev_info(&adapter->dev, "Found a DME1737 chip at 0x%02x "
+		 "(rev 0x%02x)\n", client->addr, verstep);
+
+	return 0;
+
+exit_remove:
+	for (ix = 0; ix < ARRAY_SIZE(dme1737_fan_group); ix++) {
+		if (data->has_fan & (1 << ix)) {
+			sysfs_remove_group(&client->dev.kobj,
+					   &dme1737_fan_group[ix]);
+		}
+	}
+	for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_group); ix++) {
+		if (data->has_pwm & (1 << ix)) {
+			sysfs_remove_group(&client->dev.kobj,
+					   &dme1737_pwm_group[ix]);
+		}
+	}
+	sysfs_remove_group(&client->dev.kobj, &dme1737_group);
+exit_detach:
+	i2c_detach_client(client);
+exit_kfree:
+	kfree(data);
+exit:
+	return err;
+}
+
+static int dme1737_attach_adapter(struct i2c_adapter *adapter)
+{
+	if (!(adapter->class & I2C_CLASS_HWMON)) {
+		return 0;
+	}
+
+	return i2c_probe(adapter, &addr_data, dme1737_detect);
+}
+
+static int dme1737_detach_client(struct i2c_client *client)
+{
+	struct dme1737_data *data = i2c_get_clientdata(client);
+	int ix, err;
+
+	hwmon_device_unregister(data->class_dev);
+
+	for (ix = 0; ix < ARRAY_SIZE(dme1737_fan_group); ix++) {
+		if (data->has_fan & (1 << ix)) {
+			sysfs_remove_group(&client->dev.kobj,
+					   &dme1737_fan_group[ix]);
+		}
+	}
+	for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_group); ix++) {
+		if (data->has_pwm & (1 << ix)) {
+			sysfs_remove_group(&client->dev.kobj,
+					   &dme1737_pwm_group[ix]);
+		}
+	}
+	sysfs_remove_group(&client->dev.kobj, &dme1737_group);
+
+	if ((err = i2c_detach_client(client))) {
+		return err;
+	}
+
+	kfree(data);
+	return 0;
+}
+
+static struct i2c_driver dme1737_driver = {
+	.driver = {
+		.name = "dme1737",
+	},
+	.attach_adapter	= dme1737_attach_adapter,
+	.detach_client = dme1737_detach_client,
+};
+
+static int __init dme1737_init(void)
+{
+	return i2c_add_driver(&dme1737_driver);
+}
+
+static void __exit dme1737_exit(void)
+{
+	i2c_del_driver(&dme1737_driver);
+}
+
+MODULE_AUTHOR("Juerg Haefliger <juergh@gmail.com>");
+MODULE_DESCRIPTION("DME1737 sensors");
+MODULE_LICENSE("GPL");
+
+module_init(dme1737_init);
+module_exit(dme1737_exit);
diff --git a/drivers/hwmon/ds1621.c b/drivers/hwmon/ds1621.c
index d5ac422..1212d6b 100644
--- a/drivers/hwmon/ds1621.c
+++ b/drivers/hwmon/ds1621.c
@@ -27,6 +27,7 @@
 #include <linux/jiffies.h>
 #include <linux/i2c.h>
 #include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
 #include <linux/err.h>
 #include <linux/mutex.h>
 #include <linux/sysfs.h>
@@ -52,9 +53,11 @@
 #define DS1621_REG_CONFIG_DONE		0x80
 
 /* The DS1621 registers */
-#define DS1621_REG_TEMP			0xAA /* word, RO */
-#define DS1621_REG_TEMP_MIN		0xA2 /* word, RW */
-#define DS1621_REG_TEMP_MAX		0xA1 /* word, RW */
+static const u8 DS1621_REG_TEMP[3] = {
+	0xAA,		/* input, word, RO */
+	0xA2,		/* min, word, RW */
+	0xA1,		/* max, word, RW */
+};
 #define DS1621_REG_CONF			0xAC /* byte, RW */
 #define DS1621_COM_START		0xEE /* no data */
 #define DS1621_COM_STOP			0x22 /* no data */
@@ -63,10 +66,7 @@
 #define DS1621_ALARM_TEMP_HIGH		0x40
 #define DS1621_ALARM_TEMP_LOW		0x20
 
-/* Conversions. Rounding and limit checking is only done on the TO_REG
-   variants. Note that you should be a bit careful with which arguments
-   these macros are called: arguments may be evaluated more than once.
-   Fixing this is just not worth it. */
+/* Conversions */
 #define ALARMS_FROM_REG(val) ((val) & \
                               (DS1621_ALARM_TEMP_HIGH | DS1621_ALARM_TEMP_LOW))
 
@@ -78,7 +78,7 @@
 	char valid;			/* !=0 if following fields are valid */
 	unsigned long last_updated;	/* In jiffies */
 
-	u16 temp, temp_min, temp_max;	/* Register values, word */
+	u16 temp[3];			/* Register values, word */
 	u8 conf;			/* Register encoding, combined */
 };
 
@@ -101,7 +101,7 @@
 
 /* All registers are word-sized, except for the configuration register.
    DS1621 uses a high-byte first convention, which is exactly opposite to
-   the usual practice. */
+   the SMBus standard. */
 static int ds1621_read_value(struct i2c_client *client, u8 reg)
 {
 	if (reg == DS1621_REG_CONF)
@@ -110,9 +110,6 @@
 		return swab16(i2c_smbus_read_word_data(client, reg));
 }
 
-/* All registers are word-sized, except for the configuration register.
-   DS1621 uses a high-byte first convention, which is exactly opposite to
-   the usual practice. */
 static int ds1621_write_value(struct i2c_client *client, u8 reg, u16 value)
 {
 	if (reg == DS1621_REG_CONF)
@@ -139,50 +136,61 @@
 	i2c_smbus_write_byte(client, DS1621_COM_START);
 }
 
-#define show(value)							\
-static ssize_t show_##value(struct device *dev, struct device_attribute *attr, char *buf)		\
-{									\
-	struct ds1621_data *data = ds1621_update_client(dev);		\
-	return sprintf(buf, "%d\n", LM75_TEMP_FROM_REG(data->value));	\
+static ssize_t show_temp(struct device *dev, struct device_attribute *da,
+			 char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	struct ds1621_data *data = ds1621_update_client(dev);
+	return sprintf(buf, "%d\n",
+		       LM75_TEMP_FROM_REG(data->temp[attr->index]));
 }
 
-show(temp);
-show(temp_min);
-show(temp_max);
+static ssize_t set_temp(struct device *dev, struct device_attribute *da,
+			const char *buf, size_t count)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct ds1621_data *data = ds1621_update_client(dev);
+	u16 val = LM75_TEMP_TO_REG(simple_strtoul(buf, NULL, 10));
 
-#define set_temp(suffix, value, reg)					\
-static ssize_t set_temp_##suffix(struct device *dev, struct device_attribute *attr, const char *buf,	\
-				 size_t count)				\
-{									\
-	struct i2c_client *client = to_i2c_client(dev);			\
-	struct ds1621_data *data = ds1621_update_client(dev);		\
-	u16 val = LM75_TEMP_TO_REG(simple_strtoul(buf, NULL, 10));	\
-									\
-	mutex_lock(&data->update_lock);					\
-	data->value = val;						\
-	ds1621_write_value(client, reg, data->value);			\
-	mutex_unlock(&data->update_lock);				\
-	return count;							\
+	mutex_lock(&data->update_lock);
+	data->temp[attr->index] = val;
+	ds1621_write_value(client, DS1621_REG_TEMP[attr->index],
+			   data->temp[attr->index]);
+	mutex_unlock(&data->update_lock);
+	return count;
 }
 
-set_temp(min, temp_min, DS1621_REG_TEMP_MIN);
-set_temp(max, temp_max, DS1621_REG_TEMP_MAX);
-
-static ssize_t show_alarms(struct device *dev, struct device_attribute *attr, char *buf)
+static ssize_t show_alarms(struct device *dev, struct device_attribute *da,
+			   char *buf)
 {
 	struct ds1621_data *data = ds1621_update_client(dev);
 	return sprintf(buf, "%d\n", ALARMS_FROM_REG(data->conf));
 }
 
+static ssize_t show_alarm(struct device *dev, struct device_attribute *da,
+			  char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	struct ds1621_data *data = ds1621_update_client(dev);
+	return sprintf(buf, "%d\n", !!(data->conf & attr->index));
+}
+
 static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
-static DEVICE_ATTR(temp1_input, S_IRUGO , show_temp, NULL);
-static DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO , show_temp_min, set_temp_min);
-static DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp_max, set_temp_max);
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO, show_temp, set_temp, 1);
+static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp, set_temp, 2);
+static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL,
+		DS1621_ALARM_TEMP_LOW);
+static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL,
+		DS1621_ALARM_TEMP_HIGH);
 
 static struct attribute *ds1621_attributes[] = {
-	&dev_attr_temp1_input.attr,
-	&dev_attr_temp1_min.attr,
-	&dev_attr_temp1_max.attr,
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	&sensor_dev_attr_temp1_min.dev_attr.attr,
+	&sensor_dev_attr_temp1_max.dev_attr.attr,
+	&sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
+	&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
 	&dev_attr_alarms.attr,
 	NULL
 };
@@ -204,9 +212,9 @@
 			 int kind)
 {
 	int conf, temp;
-	struct i2c_client *new_client;
+	struct i2c_client *client;
 	struct ds1621_data *data;
-	int err = 0;
+	int i, err = 0;
 
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA 
 				     | I2C_FUNC_SMBUS_WORD_DATA 
@@ -221,55 +229,44 @@
 		goto exit;
 	}
 	
-	new_client = &data->client;
-	i2c_set_clientdata(new_client, data);
-	new_client->addr = address;
-	new_client->adapter = adapter;
-	new_client->driver = &ds1621_driver;
-	new_client->flags = 0;
-
+	client = &data->client;
+	i2c_set_clientdata(client, data);
+	client->addr = address;
+	client->adapter = adapter;
+	client->driver = &ds1621_driver;
 
 	/* Now, we do the remaining detection. It is lousy. */
 	if (kind < 0) {
 		/* The NVB bit should be low if no EEPROM write has been 
 		   requested during the latest 10ms, which is highly 
 		   improbable in our case. */
-		conf = ds1621_read_value(new_client, DS1621_REG_CONF);
+		conf = ds1621_read_value(client, DS1621_REG_CONF);
 		if (conf & DS1621_REG_CONFIG_NVB)
 			goto exit_free;
 		/* The 7 lowest bits of a temperature should always be 0. */
-		temp = ds1621_read_value(new_client, DS1621_REG_TEMP);
-		if (temp & 0x007f)
-			goto exit_free;
-		temp = ds1621_read_value(new_client, DS1621_REG_TEMP_MIN);
-		if (temp & 0x007f)
-			goto exit_free;
-		temp = ds1621_read_value(new_client, DS1621_REG_TEMP_MAX);
-		if (temp & 0x007f)
-			goto exit_free;
+		for (i = 0; i < ARRAY_SIZE(data->temp); i++) {
+			temp = ds1621_read_value(client, DS1621_REG_TEMP[i]);
+			if (temp & 0x007f)
+				goto exit_free;
+		}
 	}
 
-	/* Determine the chip type - only one kind supported! */
-	if (kind <= 0)
-		kind = ds1621;
-
 	/* Fill in remaining client fields and put it into the global list */
-	strlcpy(new_client->name, "ds1621", I2C_NAME_SIZE);
-	data->valid = 0;
+	strlcpy(client->name, "ds1621", I2C_NAME_SIZE);
 	mutex_init(&data->update_lock);
 
 	/* Tell the I2C layer a new client has arrived */
-	if ((err = i2c_attach_client(new_client)))
+	if ((err = i2c_attach_client(client)))
 		goto exit_free;
 
 	/* Initialize the DS1621 chip */
-	ds1621_init_client(new_client);
+	ds1621_init_client(client);
 
 	/* Register sysfs hooks */
-	if ((err = sysfs_create_group(&new_client->dev.kobj, &ds1621_group)))
+	if ((err = sysfs_create_group(&client->dev.kobj, &ds1621_group)))
 		goto exit_detach;
 
-	data->class_dev = hwmon_device_register(&new_client->dev);
+	data->class_dev = hwmon_device_register(&client->dev);
 	if (IS_ERR(data->class_dev)) {
 		err = PTR_ERR(data->class_dev);
 		goto exit_remove_files;
@@ -278,9 +275,9 @@
 	return 0;
 
       exit_remove_files:
-	sysfs_remove_group(&new_client->dev.kobj, &ds1621_group);
+	sysfs_remove_group(&client->dev.kobj, &ds1621_group);
       exit_detach:
-	i2c_detach_client(new_client);
+	i2c_detach_client(client);
       exit_free:
 	kfree(data);
       exit:
@@ -314,23 +311,21 @@
 
 	if (time_after(jiffies, data->last_updated + HZ + HZ / 2)
 	    || !data->valid) {
+		int i;
 
 		dev_dbg(&client->dev, "Starting ds1621 update\n");
 
 		data->conf = ds1621_read_value(client, DS1621_REG_CONF);
 
-		data->temp = ds1621_read_value(client, DS1621_REG_TEMP);
-		
-		data->temp_min = ds1621_read_value(client,
-		                                    DS1621_REG_TEMP_MIN);
-		data->temp_max = ds1621_read_value(client,
-						    DS1621_REG_TEMP_MAX);
+		for (i = 0; i < ARRAY_SIZE(data->temp); i++)
+			data->temp[i] = ds1621_read_value(client,
+							  DS1621_REG_TEMP[i]);
 
 		/* reset alarms if necessary */
 		new_conf = data->conf;
-		if (data->temp > data->temp_min)
+		if (data->temp[0] > data->temp[1])	/* input > min */
 			new_conf &= ~DS1621_ALARM_TEMP_LOW;
-		if (data->temp < data->temp_max)
+		if (data->temp[0] < data->temp[2])	/* input < max */
 			new_conf &= ~DS1621_ALARM_TEMP_HIGH;
 		if (data->conf != new_conf)
 			ds1621_write_value(client, DS1621_REG_CONF,
diff --git a/drivers/hwmon/f71805f.c b/drivers/hwmon/f71805f.c
index cdbe309..6f60715 100644
--- a/drivers/hwmon/f71805f.c
+++ b/drivers/hwmon/f71805f.c
@@ -127,6 +127,13 @@
 #define F71805F_REG_TEMP_HIGH(nr)	(0x54 + 2 * (nr))
 #define F71805F_REG_TEMP_HYST(nr)	(0x55 + 2 * (nr))
 #define F71805F_REG_TEMP_MODE		0x01
+/* pwm/fan pwmnr from 0 to 2, auto point apnr from 0 to 2 */
+/* map Fintek numbers to our numbers as follows: 9->0, 5->1, 1->2 */
+#define F71805F_REG_PWM_AUTO_POINT_TEMP(pwmnr, apnr) \
+					(0xA0 + 0x10 * (pwmnr) + (2 - (apnr)))
+#define F71805F_REG_PWM_AUTO_POINT_FAN(pwmnr, apnr) \
+					(0xA4 + 0x10 * (pwmnr) + \
+						2 * (2 - (apnr)))
 
 #define F71805F_REG_START		0x00
 /* status nr from 0 to 2 */
@@ -144,6 +151,11 @@
  * Data structures and manipulation thereof
  */
 
+struct f71805f_auto_point {
+	u8 temp[3];
+	u16 fan[3];
+};
+
 struct f71805f_data {
 	unsigned short addr;
 	const char *name;
@@ -170,6 +182,7 @@
 	u8 temp_hyst[3];
 	u8 temp_mode;
 	unsigned long alarms;
+	struct f71805f_auto_point auto_points[3];
 };
 
 struct f71805f_sio_data {
@@ -312,7 +325,7 @@
 static struct f71805f_data *f71805f_update_device(struct device *dev)
 {
 	struct f71805f_data *data = dev_get_drvdata(dev);
-	int nr;
+	int nr, apnr;
 
 	mutex_lock(&data->update_lock);
 
@@ -342,6 +355,18 @@
 					      F71805F_REG_TEMP_HYST(nr));
 		}
 		data->temp_mode = f71805f_read8(data, F71805F_REG_TEMP_MODE);
+		for (nr = 0; nr < 3; nr++) {
+			for (apnr = 0; apnr < 3; apnr++) {
+				data->auto_points[nr].temp[apnr] =
+					f71805f_read8(data,
+					F71805F_REG_PWM_AUTO_POINT_TEMP(nr,
+									apnr));
+				data->auto_points[nr].fan[apnr] =
+					f71805f_read16(data,
+					F71805F_REG_PWM_AUTO_POINT_FAN(nr,
+								       apnr));
+			}
+		}
 
 		data->last_limits = jiffies;
 	}
@@ -705,6 +730,70 @@
 	return count;
 }
 
+static ssize_t show_pwm_auto_point_temp(struct device *dev,
+					struct device_attribute *devattr,
+					char* buf)
+{
+	struct f71805f_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	int pwmnr = attr->nr;
+	int apnr = attr->index;
+
+	return sprintf(buf, "%ld\n",
+		       temp_from_reg(data->auto_points[pwmnr].temp[apnr]));
+}
+
+static ssize_t set_pwm_auto_point_temp(struct device *dev,
+				       struct device_attribute *devattr,
+				       const char* buf, size_t count)
+{
+	struct f71805f_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	int pwmnr = attr->nr;
+	int apnr = attr->index;
+	unsigned long val = simple_strtol(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	data->auto_points[pwmnr].temp[apnr] = temp_to_reg(val);
+	f71805f_write8(data, F71805F_REG_PWM_AUTO_POINT_TEMP(pwmnr, apnr),
+		       data->auto_points[pwmnr].temp[apnr]);
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+static ssize_t show_pwm_auto_point_fan(struct device *dev,
+				       struct device_attribute *devattr,
+				       char* buf)
+{
+	struct f71805f_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	int pwmnr = attr->nr;
+	int apnr = attr->index;
+
+	return sprintf(buf, "%ld\n",
+		       fan_from_reg(data->auto_points[pwmnr].fan[apnr]));
+}
+
+static ssize_t set_pwm_auto_point_fan(struct device *dev,
+				      struct device_attribute *devattr,
+				      const char* buf, size_t count)
+{
+	struct f71805f_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	int pwmnr = attr->nr;
+	int apnr = attr->index;
+	unsigned long val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	data->auto_points[pwmnr].fan[apnr] = fan_to_reg(val);
+	f71805f_write16(data, F71805F_REG_PWM_AUTO_POINT_FAN(pwmnr, apnr),
+		        data->auto_points[pwmnr].fan[apnr]);
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
 static ssize_t show_temp(struct device *dev, struct device_attribute *devattr,
 			 char *buf)
 {
@@ -932,6 +1021,63 @@
 			  show_pwm_freq, set_pwm_freq, 2);
 static SENSOR_DEVICE_ATTR(pwm3_mode, S_IRUGO, show_pwm_mode, NULL, 2);
 
+static SENSOR_DEVICE_ATTR_2(pwm1_auto_point1_temp, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_temp, set_pwm_auto_point_temp,
+			    0, 0);
+static SENSOR_DEVICE_ATTR_2(pwm1_auto_point1_fan, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_fan, set_pwm_auto_point_fan,
+			    0, 0);
+static SENSOR_DEVICE_ATTR_2(pwm1_auto_point2_temp, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_temp, set_pwm_auto_point_temp,
+			    0, 1);
+static SENSOR_DEVICE_ATTR_2(pwm1_auto_point2_fan, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_fan, set_pwm_auto_point_fan,
+			    0, 1);
+static SENSOR_DEVICE_ATTR_2(pwm1_auto_point3_temp, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_temp, set_pwm_auto_point_temp,
+			    0, 2);
+static SENSOR_DEVICE_ATTR_2(pwm1_auto_point3_fan, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_fan, set_pwm_auto_point_fan,
+			    0, 2);
+
+static SENSOR_DEVICE_ATTR_2(pwm2_auto_point1_temp, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_temp, set_pwm_auto_point_temp,
+			    1, 0);
+static SENSOR_DEVICE_ATTR_2(pwm2_auto_point1_fan, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_fan, set_pwm_auto_point_fan,
+			    1, 0);
+static SENSOR_DEVICE_ATTR_2(pwm2_auto_point2_temp, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_temp, set_pwm_auto_point_temp,
+			    1, 1);
+static SENSOR_DEVICE_ATTR_2(pwm2_auto_point2_fan, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_fan, set_pwm_auto_point_fan,
+			    1, 1);
+static SENSOR_DEVICE_ATTR_2(pwm2_auto_point3_temp, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_temp, set_pwm_auto_point_temp,
+			    1, 2);
+static SENSOR_DEVICE_ATTR_2(pwm2_auto_point3_fan, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_fan, set_pwm_auto_point_fan,
+			    1, 2);
+
+static SENSOR_DEVICE_ATTR_2(pwm3_auto_point1_temp, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_temp, set_pwm_auto_point_temp,
+			    2, 0);
+static SENSOR_DEVICE_ATTR_2(pwm3_auto_point1_fan, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_fan, set_pwm_auto_point_fan,
+			    2, 0);
+static SENSOR_DEVICE_ATTR_2(pwm3_auto_point2_temp, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_temp, set_pwm_auto_point_temp,
+			    2, 1);
+static SENSOR_DEVICE_ATTR_2(pwm3_auto_point2_fan, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_fan, set_pwm_auto_point_fan,
+			    2, 1);
+static SENSOR_DEVICE_ATTR_2(pwm3_auto_point3_temp, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_temp, set_pwm_auto_point_temp,
+			    2, 2);
+static SENSOR_DEVICE_ATTR_2(pwm3_auto_point3_fan, S_IRUGO | S_IWUSR,
+			    show_pwm_auto_point_fan, set_pwm_auto_point_fan,
+			    2, 2);
+
 static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0);
 static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 1);
 static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 2);
@@ -1014,6 +1160,25 @@
 	&sensor_dev_attr_temp3_max_hyst.dev_attr.attr,
 	&sensor_dev_attr_temp3_type.dev_attr.attr,
 
+	&sensor_dev_attr_pwm1_auto_point1_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point1_fan.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point2_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point2_fan.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point3_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point3_fan.dev_attr.attr,
+	&sensor_dev_attr_pwm2_auto_point1_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm2_auto_point1_fan.dev_attr.attr,
+	&sensor_dev_attr_pwm2_auto_point2_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm2_auto_point2_fan.dev_attr.attr,
+	&sensor_dev_attr_pwm2_auto_point3_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm2_auto_point3_fan.dev_attr.attr,
+	&sensor_dev_attr_pwm3_auto_point1_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm3_auto_point1_fan.dev_attr.attr,
+	&sensor_dev_attr_pwm3_auto_point2_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm3_auto_point2_fan.dev_attr.attr,
+	&sensor_dev_attr_pwm3_auto_point3_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm3_auto_point3_fan.dev_attr.attr,
+
 	&sensor_dev_attr_in0_alarm.dev_attr.attr,
 	&sensor_dev_attr_in1_alarm.dev_attr.attr,
 	&sensor_dev_attr_in2_alarm.dev_attr.attr,
@@ -1242,12 +1407,12 @@
 	struct resource *res;
 	int i;
 
-	platform_set_drvdata(pdev, NULL);
 	hwmon_device_unregister(data->class_dev);
 	sysfs_remove_group(&pdev->dev.kobj, &f71805f_group);
 	for (i = 0; i < 4; i++)
 		sysfs_remove_group(&pdev->dev.kobj, &f71805f_group_optin[i]);
 	sysfs_remove_group(&pdev->dev.kobj, &f71805f_group_pwm_freq);
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 
 	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
@@ -1290,15 +1455,12 @@
 		goto exit_device_put;
 	}
 
-	pdev->dev.platform_data = kmalloc(sizeof(struct f71805f_sio_data),
-					  GFP_KERNEL);
-	if (!pdev->dev.platform_data) {
-		err = -ENOMEM;
+	err = platform_device_add_data(pdev, sio_data,
+				       sizeof(struct f71805f_sio_data));
+	if (err) {
 		printk(KERN_ERR DRVNAME ": Platform data allocation failed\n");
 		goto exit_device_put;
 	}
-	memcpy(pdev->dev.platform_data, sio_data,
-	       sizeof(struct f71805f_sio_data));
 
 	err = platform_device_add(pdev);
 	if (err) {
diff --git a/drivers/hwmon/it87.c b/drivers/hwmon/it87.c
index 62afc63..eff6036 100644
--- a/drivers/hwmon/it87.c
+++ b/drivers/hwmon/it87.c
@@ -6,6 +6,7 @@
               IT8712F  Super I/O chip w/LPC interface
               IT8716F  Super I/O chip w/LPC interface
               IT8718F  Super I/O chip w/LPC interface
+              IT8726F  Super I/O chip w/LPC interface
               Sis950   A clone of the IT8705F
 
     Copyright (C) 2001 Chris Gauthron <chrisg@0-in.com> 
@@ -30,8 +31,7 @@
 #include <linux/init.h>
 #include <linux/slab.h>
 #include <linux/jiffies.h>
-#include <linux/i2c.h>
-#include <linux/i2c-isa.h>
+#include <linux/platform_device.h>
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
 #include <linux/hwmon-vid.h>
@@ -40,10 +40,12 @@
 #include <linux/sysfs.h>
 #include <asm/io.h>
 
+#define DRVNAME "it87"
 
-static unsigned short isa_address;
 enum chips { it87, it8712, it8716, it8718 };
 
+static struct platform_device *pdev;
+
 #define	REG	0x2e	/* The register to read/write */
 #define	DEV	0x07	/* Register: Logical device select */
 #define	VAL	0x2f	/* The value to read/write */
@@ -97,6 +99,7 @@
 #define IT8705F_DEVID 0x8705
 #define IT8716F_DEVID 0x8716
 #define IT8718F_DEVID 0x8718
+#define IT8726F_DEVID 0x8726
 #define IT87_ACT_REG  0x30
 #define IT87_BASE_REG 0x60
 
@@ -110,10 +113,6 @@
 /* Not all BIOSes properly configure the PWM registers */
 static int fix_pwm_polarity;
 
-/* Values read from Super-I/O config space */
-static u16 chip_type;
-static u8 vid_value;
-
 /* Many IT87 constants specified below */
 
 /* Length of ISA address segment */
@@ -214,13 +213,20 @@
 };
 
 
+struct it87_sio_data {
+	enum chips type;
+	/* Values read from Super-I/O config space */
+	u8 vid_value;
+};
+
 /* For each registered chip, we need to keep some data in memory.
    The structure is dynamically allocated. */
 struct it87_data {
-	struct i2c_client client;
 	struct class_device *class_dev;
 	enum chips type;
 
+	unsigned short addr;
+	const char *name;
 	struct mutex update_lock;
 	char valid;		/* !=0 if following fields are valid */
 	unsigned long last_updated;	/* In jiffies */
@@ -245,26 +251,25 @@
 };
 
 
-static int it87_detect(struct i2c_adapter *adapter);
-static int it87_detach_client(struct i2c_client *client);
+static int it87_probe(struct platform_device *pdev);
+static int it87_remove(struct platform_device *pdev);
 
-static int it87_read_value(struct i2c_client *client, u8 reg);
-static void it87_write_value(struct i2c_client *client, u8 reg, u8 value);
+static int it87_read_value(struct it87_data *data, u8 reg);
+static void it87_write_value(struct it87_data *data, u8 reg, u8 value);
 static struct it87_data *it87_update_device(struct device *dev);
-static int it87_check_pwm(struct i2c_client *client);
-static void it87_init_client(struct i2c_client *client, struct it87_data *data);
+static int it87_check_pwm(struct device *dev);
+static void it87_init_device(struct platform_device *pdev);
 
 
-static struct i2c_driver it87_isa_driver = {
+static struct platform_driver it87_driver = {
 	.driver = {
 		.owner	= THIS_MODULE,
-		.name	= "it87-isa",
+		.name	= DRVNAME,
 	},
-	.attach_adapter	= it87_detect,
-	.detach_client	= it87_detach_client,
+	.probe	= it87_probe,
+	.remove	= __devexit_p(it87_remove),
 };
 
-
 static ssize_t show_in(struct device *dev, struct device_attribute *attr,
 		char *buf)
 {
@@ -301,13 +306,12 @@
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->in_min[nr] = IN_TO_REG(val);
-	it87_write_value(client, IT87_REG_VIN_MIN(nr), 
+	it87_write_value(data, IT87_REG_VIN_MIN(nr),
 			data->in_min[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
@@ -318,13 +322,12 @@
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->in_max[nr] = IN_TO_REG(val);
-	it87_write_value(client, IT87_REG_VIN_MAX(nr), 
+	it87_write_value(data, IT87_REG_VIN_MAX(nr),
 			data->in_max[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
@@ -392,13 +395,12 @@
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	int val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->temp_high[nr] = TEMP_TO_REG(val);
-	it87_write_value(client, IT87_REG_TEMP_HIGH(nr), data->temp_high[nr]);
+	it87_write_value(data, IT87_REG_TEMP_HIGH(nr), data->temp_high[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -408,13 +410,12 @@
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	int val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->temp_low[nr] = TEMP_TO_REG(val);
-	it87_write_value(client, IT87_REG_TEMP_LOW(nr), data->temp_low[nr]);
+	it87_write_value(data, IT87_REG_TEMP_LOW(nr), data->temp_low[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -451,8 +452,7 @@
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	int val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
@@ -468,7 +468,7 @@
 		mutex_unlock(&data->update_lock);
 		return -EINVAL;
 	}
-	it87_write_value(client, IT87_REG_TEMP_ENABLE, data->sensor);
+	it87_write_value(data, IT87_REG_TEMP_ENABLE, data->sensor);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -542,13 +542,12 @@
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	int val = simple_strtol(buf, NULL, 10);
 	u8 reg;
 
 	mutex_lock(&data->update_lock);
-	reg = it87_read_value(client, IT87_REG_FAN_DIV);
+	reg = it87_read_value(data, IT87_REG_FAN_DIV);
 	switch (nr) {
 	case 0: data->fan_div[nr] = reg & 0x07; break;
 	case 1: data->fan_div[nr] = (reg >> 3) & 0x07; break;
@@ -556,7 +555,7 @@
 	}
 
 	data->fan_min[nr] = FAN_TO_REG(val, DIV_FROM_REG(data->fan_div[nr]));
-	it87_write_value(client, IT87_REG_FAN_MIN(nr), data->fan_min[nr]);
+	it87_write_value(data, IT87_REG_FAN_MIN(nr), data->fan_min[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -566,14 +565,13 @@
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 	int min;
 	u8 old;
 
 	mutex_lock(&data->update_lock);
-	old = it87_read_value(client, IT87_REG_FAN_DIV);
+	old = it87_read_value(data, IT87_REG_FAN_DIV);
 
 	/* Save fan min limit */
 	min = FAN_FROM_REG(data->fan_min[nr], DIV_FROM_REG(data->fan_div[nr]));
@@ -594,11 +592,11 @@
 	val |= (data->fan_div[1] & 0x07) << 3;
 	if (data->fan_div[2] == 3)
 		val |= 0x1 << 6;
-	it87_write_value(client, IT87_REG_FAN_DIV, val);
+	it87_write_value(data, IT87_REG_FAN_DIV, val);
 
 	/* Restore fan min limit */
 	data->fan_min[nr] = FAN_TO_REG(min, DIV_FROM_REG(data->fan_div[nr]));
-	it87_write_value(client, IT87_REG_FAN_MIN(nr), data->fan_min[nr]);
+	it87_write_value(data, IT87_REG_FAN_MIN(nr), data->fan_min[nr]);
 
 	mutex_unlock(&data->update_lock);
 	return count;
@@ -609,8 +607,7 @@
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	int val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
@@ -618,17 +615,17 @@
 	if (val == 0) {
 		int tmp;
 		/* make sure the fan is on when in on/off mode */
-		tmp = it87_read_value(client, IT87_REG_FAN_CTL);
-		it87_write_value(client, IT87_REG_FAN_CTL, tmp | (1 << nr));
+		tmp = it87_read_value(data, IT87_REG_FAN_CTL);
+		it87_write_value(data, IT87_REG_FAN_CTL, tmp | (1 << nr));
 		/* set on/off mode */
 		data->fan_main_ctrl &= ~(1 << nr);
-		it87_write_value(client, IT87_REG_FAN_MAIN_CTRL, data->fan_main_ctrl);
+		it87_write_value(data, IT87_REG_FAN_MAIN_CTRL, data->fan_main_ctrl);
 	} else if (val == 1) {
 		/* set SmartGuardian mode */
 		data->fan_main_ctrl |= (1 << nr);
-		it87_write_value(client, IT87_REG_FAN_MAIN_CTRL, data->fan_main_ctrl);
+		it87_write_value(data, IT87_REG_FAN_MAIN_CTRL, data->fan_main_ctrl);
 		/* set saved pwm value, clear FAN_CTLX PWM mode bit */
-		it87_write_value(client, IT87_REG_PWM(nr), PWM_TO_REG(data->manual_pwm_ctl[nr]));
+		it87_write_value(data, IT87_REG_PWM(nr), PWM_TO_REG(data->manual_pwm_ctl[nr]));
 	} else {
 		mutex_unlock(&data->update_lock);
 		return -EINVAL;
@@ -643,8 +640,7 @@
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	int val = simple_strtol(buf, NULL, 10);
 
 	if (val < 0 || val > 255)
@@ -653,15 +649,14 @@
 	mutex_lock(&data->update_lock);
 	data->manual_pwm_ctl[nr] = val;
 	if (data->fan_main_ctrl & (1 << nr))
-		it87_write_value(client, IT87_REG_PWM(nr), PWM_TO_REG(data->manual_pwm_ctl[nr]));
+		it87_write_value(data, IT87_REG_PWM(nr), PWM_TO_REG(data->manual_pwm_ctl[nr]));
 	mutex_unlock(&data->update_lock);
 	return count;
 }
 static ssize_t set_pwm_freq(struct device *dev,
 		struct device_attribute *attr, const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 	int i;
 
@@ -672,9 +667,9 @@
 	}
 
 	mutex_lock(&data->update_lock);
-	data->fan_ctl = it87_read_value(client, IT87_REG_FAN_CTL) & 0x8f;
+	data->fan_ctl = it87_read_value(data, IT87_REG_FAN_CTL) & 0x8f;
 	data->fan_ctl |= i << 4;
-	it87_write_value(client, IT87_REG_FAN_CTL, data->fan_ctl);
+	it87_write_value(data, IT87_REG_FAN_CTL, data->fan_ctl);
 	mutex_unlock(&data->update_lock);
 
 	return count;
@@ -729,15 +724,14 @@
 {
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	int val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->fan_min[nr] = FAN16_TO_REG(val);
-	it87_write_value(client, IT87_REG_FAN_MIN(nr),
+	it87_write_value(data, IT87_REG_FAN_MIN(nr),
 			 data->fan_min[nr] & 0xff);
-	it87_write_value(client, IT87_REG_FANX_MIN(nr),
+	it87_write_value(data, IT87_REG_FANX_MIN(nr),
 			 data->fan_min[nr] >> 8);
 	mutex_unlock(&data->update_lock);
 	return count;
@@ -775,8 +769,7 @@
 static ssize_t
 store_vrm_reg(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	u32 val;
 
 	val = simple_strtoul(buf, NULL, 10);
@@ -794,6 +787,14 @@
 }
 static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid_reg, NULL);
 
+static ssize_t show_name(struct device *dev, struct device_attribute
+			 *devattr, char *buf)
+{
+	struct it87_data *data = dev_get_drvdata(dev);
+	return sprintf(buf, "%s\n", data->name);
+}
+static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
+
 static struct attribute *it87_attributes[] = {
 	&sensor_dev_attr_in0_input.dev_attr.attr,
 	&sensor_dev_attr_in1_input.dev_attr.attr,
@@ -835,6 +836,7 @@
 	&sensor_dev_attr_temp3_type.dev_attr.attr,
 
 	&dev_attr_alarms.attr,
+	&dev_attr_name.attr,
 	NULL
 };
 
@@ -877,17 +879,36 @@
 };
 
 /* SuperIO detection - will change isa_address if a chip is found */
-static int __init it87_find(unsigned short *address)
+static int __init it87_find(unsigned short *address,
+	struct it87_sio_data *sio_data)
 {
 	int err = -ENODEV;
+	u16 chip_type;
 
 	superio_enter();
 	chip_type = superio_inw(DEVID);
-	if (chip_type != IT8712F_DEVID
-	 && chip_type != IT8716F_DEVID
-	 && chip_type != IT8718F_DEVID
-	 && chip_type != IT8705F_DEVID)
-	 	goto exit;
+
+	switch (chip_type) {
+	case IT8705F_DEVID:
+		sio_data->type = it87;
+		break;
+	case IT8712F_DEVID:
+		sio_data->type = it8712;
+		break;
+	case IT8716F_DEVID:
+	case IT8726F_DEVID:
+		sio_data->type = it8716;
+		break;
+	case IT8718F_DEVID:
+		sio_data->type = it8718;
+		break;
+	case 0xffff:	/* No device at all */
+		goto exit;
+	default:
+		pr_debug(DRVNAME ": Unsupported chip (DEVID=0x%x)\n",
+			 chip_type);
+		goto exit;
+	}
 
 	superio_select(PME);
 	if (!(superio_inb(IT87_ACT_REG) & 0x01)) {
@@ -911,7 +932,7 @@
 
 		superio_select(GPIO);
 		if (chip_type == it8718)
-			vid_value = superio_inb(IT87_SIO_VID_REG);
+			sio_data->vid_value = superio_inb(IT87_SIO_VID_REG);
 
 		reg = superio_inb(IT87_SIO_PINX2_REG);
 		if (reg & (1 << 0))
@@ -925,18 +946,26 @@
 	return err;
 }
 
-/* This function is called by i2c_probe */
-static int it87_detect(struct i2c_adapter *adapter)
+static int __devinit it87_probe(struct platform_device *pdev)
 {
-	struct i2c_client *new_client;
 	struct it87_data *data;
+	struct resource *res;
+	struct device *dev = &pdev->dev;
+	struct it87_sio_data *sio_data = dev->platform_data;
 	int err = 0;
-	const char *name;
 	int enable_pwm_interface;
+	static const char *names[] = {
+		"it87",
+		"it8712",
+		"it8716",
+		"it8718",
+	};
 
-	/* Reserve the ISA region */
-	if (!request_region(isa_address, IT87_EXTENT,
-			    it87_isa_driver.driver.name)){
+	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+	if (!request_region(res->start, IT87_EXTENT, DRVNAME)) {
+		dev_err(dev, "Failed to request region 0x%lx-0x%lx\n",
+			(unsigned long)res->start,
+			(unsigned long)(res->start + IT87_EXTENT - 1));
 		err = -EBUSY;
 		goto ERROR0;
 	}
@@ -946,129 +975,104 @@
 		goto ERROR1;
 	}
 
-	new_client = &data->client;
-	i2c_set_clientdata(new_client, data);
-	new_client->addr = isa_address;
-	new_client->adapter = adapter;
-	new_client->driver = &it87_isa_driver;
+	data->addr = res->start;
+	data->type = sio_data->type;
+	data->name = names[sio_data->type];
 
 	/* Now, we do the remaining detection. */
-	if ((it87_read_value(new_client, IT87_REG_CONFIG) & 0x80)
-	 || it87_read_value(new_client, IT87_REG_CHIPID) != 0x90) {
+	if ((it87_read_value(data, IT87_REG_CONFIG) & 0x80)
+	 || it87_read_value(data, IT87_REG_CHIPID) != 0x90) {
 		err = -ENODEV;
 		goto ERROR2;
 	}
 
-	/* Determine the chip type. */
-	switch (chip_type) {
-	case IT8712F_DEVID:
-		data->type = it8712;
-		name = "it8712";
-		break;
-	case IT8716F_DEVID:
-		data->type = it8716;
-		name = "it8716";
-		break;
-	case IT8718F_DEVID:
-		data->type = it8718;
-		name = "it8718";
-		break;
-	default:
-		data->type = it87;
-		name = "it87";
-	}
+	platform_set_drvdata(pdev, data);
 
-	/* Fill in the remaining client fields and put it into the global list */
-	strlcpy(new_client->name, name, I2C_NAME_SIZE);
 	mutex_init(&data->update_lock);
 
-	/* Tell the I2C layer a new client has arrived */
-	if ((err = i2c_attach_client(new_client)))
-		goto ERROR2;
-
 	/* Check PWM configuration */
-	enable_pwm_interface = it87_check_pwm(new_client);
+	enable_pwm_interface = it87_check_pwm(dev);
 
 	/* Initialize the IT87 chip */
-	it87_init_client(new_client, data);
+	it87_init_device(pdev);
 
 	/* Register sysfs hooks */
-	if ((err = sysfs_create_group(&new_client->dev.kobj, &it87_group)))
-		goto ERROR3;
+	if ((err = sysfs_create_group(&dev->kobj, &it87_group)))
+		goto ERROR2;
 
 	/* Do not create fan files for disabled fans */
 	if (data->type == it8716 || data->type == it8718) {
 		/* 16-bit tachometers */
 		if (data->has_fan & (1 << 0)) {
-			if ((err = device_create_file(&new_client->dev,
+			if ((err = device_create_file(dev,
 			     &sensor_dev_attr_fan1_input16.dev_attr))
-			 || (err = device_create_file(&new_client->dev,
+			 || (err = device_create_file(dev,
 			     &sensor_dev_attr_fan1_min16.dev_attr)))
 				goto ERROR4;
 		}
 		if (data->has_fan & (1 << 1)) {
-			if ((err = device_create_file(&new_client->dev,
+			if ((err = device_create_file(dev,
 			     &sensor_dev_attr_fan2_input16.dev_attr))
-			 || (err = device_create_file(&new_client->dev,
+			 || (err = device_create_file(dev,
 			     &sensor_dev_attr_fan2_min16.dev_attr)))
 				goto ERROR4;
 		}
 		if (data->has_fan & (1 << 2)) {
-			if ((err = device_create_file(&new_client->dev,
+			if ((err = device_create_file(dev,
 			     &sensor_dev_attr_fan3_input16.dev_attr))
-			 || (err = device_create_file(&new_client->dev,
+			 || (err = device_create_file(dev,
 			     &sensor_dev_attr_fan3_min16.dev_attr)))
 				goto ERROR4;
 		}
 	} else {
 		/* 8-bit tachometers with clock divider */
 		if (data->has_fan & (1 << 0)) {
-			if ((err = device_create_file(&new_client->dev,
+			if ((err = device_create_file(dev,
 			     &sensor_dev_attr_fan1_input.dev_attr))
-			 || (err = device_create_file(&new_client->dev,
+			 || (err = device_create_file(dev,
 			     &sensor_dev_attr_fan1_min.dev_attr))
-			 || (err = device_create_file(&new_client->dev,
+			 || (err = device_create_file(dev,
 			     &sensor_dev_attr_fan1_div.dev_attr)))
 				goto ERROR4;
 		}
 		if (data->has_fan & (1 << 1)) {
-			if ((err = device_create_file(&new_client->dev,
+			if ((err = device_create_file(dev,
 			     &sensor_dev_attr_fan2_input.dev_attr))
-			 || (err = device_create_file(&new_client->dev,
+			 || (err = device_create_file(dev,
 			     &sensor_dev_attr_fan2_min.dev_attr))
-			 || (err = device_create_file(&new_client->dev,
+			 || (err = device_create_file(dev,
 			     &sensor_dev_attr_fan2_div.dev_attr)))
 				goto ERROR4;
 		}
 		if (data->has_fan & (1 << 2)) {
-			if ((err = device_create_file(&new_client->dev,
+			if ((err = device_create_file(dev,
 			     &sensor_dev_attr_fan3_input.dev_attr))
-			 || (err = device_create_file(&new_client->dev,
+			 || (err = device_create_file(dev,
 			     &sensor_dev_attr_fan3_min.dev_attr))
-			 || (err = device_create_file(&new_client->dev,
+			 || (err = device_create_file(dev,
 			     &sensor_dev_attr_fan3_div.dev_attr)))
 				goto ERROR4;
 		}
 	}
 
 	if (enable_pwm_interface) {
-		if ((err = device_create_file(&new_client->dev,
+		if ((err = device_create_file(dev,
 		     &sensor_dev_attr_pwm1_enable.dev_attr))
-		 || (err = device_create_file(&new_client->dev,
+		 || (err = device_create_file(dev,
 		     &sensor_dev_attr_pwm2_enable.dev_attr))
-		 || (err = device_create_file(&new_client->dev,
+		 || (err = device_create_file(dev,
 		     &sensor_dev_attr_pwm3_enable.dev_attr))
-		 || (err = device_create_file(&new_client->dev,
+		 || (err = device_create_file(dev,
 		     &sensor_dev_attr_pwm1.dev_attr))
-		 || (err = device_create_file(&new_client->dev,
+		 || (err = device_create_file(dev,
 		     &sensor_dev_attr_pwm2.dev_attr))
-		 || (err = device_create_file(&new_client->dev,
+		 || (err = device_create_file(dev,
 		     &sensor_dev_attr_pwm3.dev_attr))
-		 || (err = device_create_file(&new_client->dev,
+		 || (err = device_create_file(dev,
 		     &dev_attr_pwm1_freq))
-		 || (err = device_create_file(&new_client->dev,
+		 || (err = device_create_file(dev,
 		     &dev_attr_pwm2_freq))
-		 || (err = device_create_file(&new_client->dev,
+		 || (err = device_create_file(dev,
 		     &dev_attr_pwm3_freq)))
 			goto ERROR4;
 	}
@@ -1077,15 +1081,15 @@
 	 || data->type == it8718) {
 		data->vrm = vid_which_vrm();
 		/* VID reading from Super-I/O config space if available */
-		data->vid = vid_value;
-		if ((err = device_create_file(&new_client->dev,
+		data->vid = sio_data->vid_value;
+		if ((err = device_create_file(dev,
 		     &dev_attr_vrm))
-		 || (err = device_create_file(&new_client->dev,
+		 || (err = device_create_file(dev,
 		     &dev_attr_cpu0_vid)))
 			goto ERROR4;
 	}
 
-	data->class_dev = hwmon_device_register(&new_client->dev);
+	data->class_dev = hwmon_device_register(dev);
 	if (IS_ERR(data->class_dev)) {
 		err = PTR_ERR(data->class_dev);
 		goto ERROR4;
@@ -1094,31 +1098,27 @@
 	return 0;
 
 ERROR4:
-	sysfs_remove_group(&new_client->dev.kobj, &it87_group);
-	sysfs_remove_group(&new_client->dev.kobj, &it87_group_opt);
-ERROR3:
-	i2c_detach_client(new_client);
+	sysfs_remove_group(&dev->kobj, &it87_group);
+	sysfs_remove_group(&dev->kobj, &it87_group_opt);
 ERROR2:
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 ERROR1:
-	release_region(isa_address, IT87_EXTENT);
+	release_region(res->start, IT87_EXTENT);
 ERROR0:
 	return err;
 }
 
-static int it87_detach_client(struct i2c_client *client)
+static int __devexit it87_remove(struct platform_device *pdev)
 {
-	struct it87_data *data = i2c_get_clientdata(client);
-	int err;
+	struct it87_data *data = platform_get_drvdata(pdev);
 
 	hwmon_device_unregister(data->class_dev);
-	sysfs_remove_group(&client->dev.kobj, &it87_group);
-	sysfs_remove_group(&client->dev.kobj, &it87_group_opt);
+	sysfs_remove_group(&pdev->dev.kobj, &it87_group);
+	sysfs_remove_group(&pdev->dev.kobj, &it87_group_opt);
 
-	if ((err = i2c_detach_client(client)))
-		return err;
-
-	release_region(client->addr, IT87_EXTENT);
+	release_region(data->addr, IT87_EXTENT);
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 
 	return 0;
@@ -1127,28 +1127,29 @@
 /* Must be called with data->update_lock held, except during initialization.
    We ignore the IT87 BUSY flag at this moment - it could lead to deadlocks,
    would slow down the IT87 access and should not be necessary. */
-static int it87_read_value(struct i2c_client *client, u8 reg)
+static int it87_read_value(struct it87_data *data, u8 reg)
 {
-	outb_p(reg, client->addr + IT87_ADDR_REG_OFFSET);
-	return inb_p(client->addr + IT87_DATA_REG_OFFSET);
+	outb_p(reg, data->addr + IT87_ADDR_REG_OFFSET);
+	return inb_p(data->addr + IT87_DATA_REG_OFFSET);
 }
 
 /* Must be called with data->update_lock held, except during initialization.
    We ignore the IT87 BUSY flag at this moment - it could lead to deadlocks,
    would slow down the IT87 access and should not be necessary. */
-static void it87_write_value(struct i2c_client *client, u8 reg, u8 value)
+static void it87_write_value(struct it87_data *data, u8 reg, u8 value)
 {
-	outb_p(reg, client->addr + IT87_ADDR_REG_OFFSET);
-	outb_p(value, client->addr + IT87_DATA_REG_OFFSET);
+	outb_p(reg, data->addr + IT87_ADDR_REG_OFFSET);
+	outb_p(value, data->addr + IT87_DATA_REG_OFFSET);
 }
 
 /* Return 1 if and only if the PWM interface is safe to use */
-static int it87_check_pwm(struct i2c_client *client)
+static int __devinit it87_check_pwm(struct device *dev)
 {
+	struct it87_data *data = dev_get_drvdata(dev);
 	/* Some BIOSes fail to correctly configure the IT87 fans. All fans off
 	 * and polarity set to active low is sign that this is the case so we
 	 * disable pwm control to protect the user. */
-	int tmp = it87_read_value(client, IT87_REG_FAN_CTL);
+	int tmp = it87_read_value(data, IT87_REG_FAN_CTL);
 	if ((tmp & 0x87) == 0) {
 		if (fix_pwm_polarity) {
 			/* The user asks us to attempt a chip reconfiguration.
@@ -1158,7 +1159,7 @@
 			u8 pwm[3];
 
 			for (i = 0; i < 3; i++)
-				pwm[i] = it87_read_value(client,
+				pwm[i] = it87_read_value(data,
 							 IT87_REG_PWM(i));
 
 			/* If any fan is in automatic pwm mode, the polarity
@@ -1166,26 +1167,26 @@
 			 * better don't change anything (but still disable the
 			 * PWM interface). */
 			if (!((pwm[0] | pwm[1] | pwm[2]) & 0x80)) {
-				dev_info(&client->dev, "Reconfiguring PWM to "
+				dev_info(dev, "Reconfiguring PWM to "
 					 "active high polarity\n");
-				it87_write_value(client, IT87_REG_FAN_CTL,
+				it87_write_value(data, IT87_REG_FAN_CTL,
 						 tmp | 0x87);
 				for (i = 0; i < 3; i++)
-					it87_write_value(client,
+					it87_write_value(data,
 							 IT87_REG_PWM(i),
 							 0x7f & ~pwm[i]);
 				return 1;
 			}
 
-			dev_info(&client->dev, "PWM configuration is "
+			dev_info(dev, "PWM configuration is "
 				 "too broken to be fixed\n");
 		}
 
-		dev_info(&client->dev, "Detected broken BIOS "
+		dev_info(dev, "Detected broken BIOS "
 			 "defaults, disabling PWM interface\n");
 		return 0;
 	} else if (fix_pwm_polarity) {
-		dev_info(&client->dev, "PWM configuration looks "
+		dev_info(dev, "PWM configuration looks "
 			 "sane, won't touch\n");
 	}
 
@@ -1193,8 +1194,9 @@
 }
 
 /* Called when we have found a new IT87. */
-static void it87_init_client(struct i2c_client *client, struct it87_data *data)
+static void __devinit it87_init_device(struct platform_device *pdev)
 {
+	struct it87_data *data = platform_get_drvdata(pdev);
 	int tmp, i;
 
 	/* initialize to sane defaults:
@@ -1214,48 +1216,48 @@
 	 * means -1 degree C, which surprisingly doesn't trigger an alarm,
 	 * but is still confusing, so change to 127 degrees C. */
 	for (i = 0; i < 8; i++) {
-		tmp = it87_read_value(client, IT87_REG_VIN_MIN(i));
+		tmp = it87_read_value(data, IT87_REG_VIN_MIN(i));
 		if (tmp == 0xff)
-			it87_write_value(client, IT87_REG_VIN_MIN(i), 0);
+			it87_write_value(data, IT87_REG_VIN_MIN(i), 0);
 	}
 	for (i = 0; i < 3; i++) {
-		tmp = it87_read_value(client, IT87_REG_TEMP_HIGH(i));
+		tmp = it87_read_value(data, IT87_REG_TEMP_HIGH(i));
 		if (tmp == 0xff)
-			it87_write_value(client, IT87_REG_TEMP_HIGH(i), 127);
+			it87_write_value(data, IT87_REG_TEMP_HIGH(i), 127);
 	}
 
 	/* Check if temperature channnels are reset manually or by some reason */
-	tmp = it87_read_value(client, IT87_REG_TEMP_ENABLE);
+	tmp = it87_read_value(data, IT87_REG_TEMP_ENABLE);
 	if ((tmp & 0x3f) == 0) {
 		/* Temp1,Temp3=thermistor; Temp2=thermal diode */
 		tmp = (tmp & 0xc0) | 0x2a;
-		it87_write_value(client, IT87_REG_TEMP_ENABLE, tmp);
+		it87_write_value(data, IT87_REG_TEMP_ENABLE, tmp);
 	}
 	data->sensor = tmp;
 
 	/* Check if voltage monitors are reset manually or by some reason */
-	tmp = it87_read_value(client, IT87_REG_VIN_ENABLE);
+	tmp = it87_read_value(data, IT87_REG_VIN_ENABLE);
 	if ((tmp & 0xff) == 0) {
 		/* Enable all voltage monitors */
-		it87_write_value(client, IT87_REG_VIN_ENABLE, 0xff);
+		it87_write_value(data, IT87_REG_VIN_ENABLE, 0xff);
 	}
 
 	/* Check if tachometers are reset manually or by some reason */
-	data->fan_main_ctrl = it87_read_value(client, IT87_REG_FAN_MAIN_CTRL);
+	data->fan_main_ctrl = it87_read_value(data, IT87_REG_FAN_MAIN_CTRL);
 	if ((data->fan_main_ctrl & 0x70) == 0) {
 		/* Enable all fan tachometers */
 		data->fan_main_ctrl |= 0x70;
-		it87_write_value(client, IT87_REG_FAN_MAIN_CTRL, data->fan_main_ctrl);
+		it87_write_value(data, IT87_REG_FAN_MAIN_CTRL, data->fan_main_ctrl);
 	}
 	data->has_fan = (data->fan_main_ctrl >> 4) & 0x07;
 
 	/* Set tachometers to 16-bit mode if needed */
 	if (data->type == it8716 || data->type == it8718) {
-		tmp = it87_read_value(client, IT87_REG_FAN_16BIT);
+		tmp = it87_read_value(data, IT87_REG_FAN_16BIT);
 		if (~tmp & 0x07 & data->has_fan) {
-			dev_dbg(&client->dev,
+			dev_dbg(&pdev->dev,
 				"Setting fan1-3 to 16-bit mode\n");
-			it87_write_value(client, IT87_REG_FAN_16BIT,
+			it87_write_value(data, IT87_REG_FAN_16BIT,
 					 tmp | 0x07);
 		}
 	}
@@ -1265,7 +1267,7 @@
 	for (i = 0; i < 3; i++) {
 		if (data->fan_main_ctrl & (1 << i)) {
 			/* pwm mode */
-			tmp = it87_read_value(client, IT87_REG_PWM(i));
+			tmp = it87_read_value(data, IT87_REG_PWM(i));
 			if (tmp & 0x80) {
 				/* automatic pwm - not yet implemented, but
 				 * leave the settings made by the BIOS alone
@@ -1279,15 +1281,14 @@
  	}
 
 	/* Start monitoring */
-	it87_write_value(client, IT87_REG_CONFIG,
-			 (it87_read_value(client, IT87_REG_CONFIG) & 0x36)
+	it87_write_value(data, IT87_REG_CONFIG,
+			 (it87_read_value(data, IT87_REG_CONFIG) & 0x36)
 			 | (update_vbat ? 0x41 : 0x01));
 }
 
 static struct it87_data *it87_update_device(struct device *dev)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct it87_data *data = i2c_get_clientdata(client);
+	struct it87_data *data = dev_get_drvdata(dev);
 	int i;
 
 	mutex_lock(&data->update_lock);
@@ -1298,20 +1299,20 @@
 		if (update_vbat) {
 			/* Cleared after each update, so reenable.  Value
 		 	  returned by this read will be previous value */	
-			it87_write_value(client, IT87_REG_CONFIG,
-			   it87_read_value(client, IT87_REG_CONFIG) | 0x40);
+			it87_write_value(data, IT87_REG_CONFIG,
+			   it87_read_value(data, IT87_REG_CONFIG) | 0x40);
 		}
 		for (i = 0; i <= 7; i++) {
 			data->in[i] =
-			    it87_read_value(client, IT87_REG_VIN(i));
+			    it87_read_value(data, IT87_REG_VIN(i));
 			data->in_min[i] =
-			    it87_read_value(client, IT87_REG_VIN_MIN(i));
+			    it87_read_value(data, IT87_REG_VIN_MIN(i));
 			data->in_max[i] =
-			    it87_read_value(client, IT87_REG_VIN_MAX(i));
+			    it87_read_value(data, IT87_REG_VIN_MAX(i));
 		}
 		/* in8 (battery) has no limit registers */
 		data->in[8] =
-		    it87_read_value(client, IT87_REG_VIN(8));
+		    it87_read_value(data, IT87_REG_VIN(8));
 
 		for (i = 0; i < 3; i++) {
 			/* Skip disabled fans */
@@ -1319,46 +1320,47 @@
 				continue;
 
 			data->fan_min[i] =
-			    it87_read_value(client, IT87_REG_FAN_MIN(i));
-			data->fan[i] = it87_read_value(client,
+			    it87_read_value(data, IT87_REG_FAN_MIN(i));
+			data->fan[i] = it87_read_value(data,
 				       IT87_REG_FAN(i));
 			/* Add high byte if in 16-bit mode */
 			if (data->type == it8716 || data->type == it8718) {
-				data->fan[i] |= it87_read_value(client,
+				data->fan[i] |= it87_read_value(data,
 						IT87_REG_FANX(i)) << 8;
-				data->fan_min[i] |= it87_read_value(client,
+				data->fan_min[i] |= it87_read_value(data,
 						IT87_REG_FANX_MIN(i)) << 8;
 			}
 		}
 		for (i = 0; i < 3; i++) {
 			data->temp[i] =
-			    it87_read_value(client, IT87_REG_TEMP(i));
+			    it87_read_value(data, IT87_REG_TEMP(i));
 			data->temp_high[i] =
-			    it87_read_value(client, IT87_REG_TEMP_HIGH(i));
+			    it87_read_value(data, IT87_REG_TEMP_HIGH(i));
 			data->temp_low[i] =
-			    it87_read_value(client, IT87_REG_TEMP_LOW(i));
+			    it87_read_value(data, IT87_REG_TEMP_LOW(i));
 		}
 
 		/* Newer chips don't have clock dividers */
 		if ((data->has_fan & 0x07) && data->type != it8716
 		 && data->type != it8718) {
-			i = it87_read_value(client, IT87_REG_FAN_DIV);
+			i = it87_read_value(data, IT87_REG_FAN_DIV);
 			data->fan_div[0] = i & 0x07;
 			data->fan_div[1] = (i >> 3) & 0x07;
 			data->fan_div[2] = (i & 0x40) ? 3 : 1;
 		}
 
 		data->alarms =
-			it87_read_value(client, IT87_REG_ALARM1) |
-			(it87_read_value(client, IT87_REG_ALARM2) << 8) |
-			(it87_read_value(client, IT87_REG_ALARM3) << 16);
-		data->fan_main_ctrl = it87_read_value(client, IT87_REG_FAN_MAIN_CTRL);
-		data->fan_ctl = it87_read_value(client, IT87_REG_FAN_CTL);
+			it87_read_value(data, IT87_REG_ALARM1) |
+			(it87_read_value(data, IT87_REG_ALARM2) << 8) |
+			(it87_read_value(data, IT87_REG_ALARM3) << 16);
+		data->fan_main_ctrl = it87_read_value(data,
+				IT87_REG_FAN_MAIN_CTRL);
+		data->fan_ctl = it87_read_value(data, IT87_REG_FAN_CTL);
 
-		data->sensor = it87_read_value(client, IT87_REG_TEMP_ENABLE);
+		data->sensor = it87_read_value(data, IT87_REG_TEMP_ENABLE);
 		/* The 8705 does not have VID capability */
 		if (data->type == it8712 || data->type == it8716) {
-			data->vid = it87_read_value(client, IT87_REG_VID);
+			data->vid = it87_read_value(data, IT87_REG_VID);
 			/* The older IT8712F revisions had only 5 VID pins,
 			   but we assume it is always safe to read 6 bits. */
 			data->vid &= 0x3f;
@@ -1372,24 +1374,85 @@
 	return data;
 }
 
+static int __init it87_device_add(unsigned short address,
+				  const struct it87_sio_data *sio_data)
+{
+	struct resource res = {
+		.start	= address ,
+		.end	= address + IT87_EXTENT - 1,
+		.name	= DRVNAME,
+		.flags	= IORESOURCE_IO,
+	};
+	int err;
+
+	pdev = platform_device_alloc(DRVNAME, address);
+	if (!pdev) {
+		err = -ENOMEM;
+		printk(KERN_ERR DRVNAME ": Device allocation failed\n");
+		goto exit;
+	}
+
+	err = platform_device_add_resources(pdev, &res, 1);
+	if (err) {
+		printk(KERN_ERR DRVNAME ": Device resource addition failed "
+		       "(%d)\n", err);
+		goto exit_device_put;
+	}
+
+	err = platform_device_add_data(pdev, sio_data,
+				       sizeof(struct it87_sio_data));
+	if (err) {
+		printk(KERN_ERR DRVNAME ": Platform data allocation failed\n");
+		goto exit_device_put;
+	}
+
+	err = platform_device_add(pdev);
+	if (err) {
+		printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
+		       err);
+		goto exit_device_put;
+	}
+
+	return 0;
+
+exit_device_put:
+	platform_device_put(pdev);
+exit:
+	return err;
+}
+
 static int __init sm_it87_init(void)
 {
-	int res;
+	int err;
+	unsigned short isa_address=0;
+	struct it87_sio_data sio_data;
 
-	if ((res = it87_find(&isa_address)))
-		return res;
-	return i2c_isa_add_driver(&it87_isa_driver);
+	err = it87_find(&isa_address, &sio_data);
+	if (err)
+		return err;
+	err = platform_driver_register(&it87_driver);
+	if (err)
+		return err;
+
+	err = it87_device_add(isa_address, &sio_data);
+	if (err){
+		platform_driver_unregister(&it87_driver);
+		return err;
+	}
+
+	return 0;
 }
 
 static void __exit sm_it87_exit(void)
 {
-	i2c_isa_del_driver(&it87_isa_driver);
+	platform_device_unregister(pdev);
+	platform_driver_unregister(&it87_driver);
 }
 
 
 MODULE_AUTHOR("Chris Gauthron <chrisg@0-in.com>, "
 	      "Jean Delvare <khali@linux-fr.org>");
-MODULE_DESCRIPTION("IT8705F/8712F/8716F/8718F, SiS950 driver");
+MODULE_DESCRIPTION("IT8705F/8712F/8716F/8718F/8726F, SiS950 driver");
 module_param(update_vbat, bool, 0);
 MODULE_PARM_DESC(update_vbat, "Update vbat if set else return powerup value");
 module_param(fix_pwm_polarity, bool, 0);
diff --git a/drivers/hwmon/lm63.c b/drivers/hwmon/lm63.c
index d69f3cf..2162d69 100644
--- a/drivers/hwmon/lm63.c
+++ b/drivers/hwmon/lm63.c
@@ -364,7 +364,7 @@
 /* Individual alarm files */
 static SENSOR_DEVICE_ATTR(fan1_min_alarm, S_IRUGO, show_alarm, NULL, 0);
 static SENSOR_DEVICE_ATTR(temp2_crit_alarm, S_IRUGO, show_alarm, NULL, 1);
-static SENSOR_DEVICE_ATTR(temp2_input_fault, S_IRUGO, show_alarm, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 2);
 static SENSOR_DEVICE_ATTR(temp2_min_alarm, S_IRUGO, show_alarm, NULL, 3);
 static SENSOR_DEVICE_ATTR(temp2_max_alarm, S_IRUGO, show_alarm, NULL, 4);
 static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 6);
@@ -383,7 +383,7 @@
 	&dev_attr_temp2_crit_hyst.attr,
 
 	&sensor_dev_attr_temp2_crit_alarm.dev_attr.attr,
-	&sensor_dev_attr_temp2_input_fault.dev_attr.attr,
+	&sensor_dev_attr_temp2_fault.dev_attr.attr,
 	&sensor_dev_attr_temp2_min_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp2_max_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
diff --git a/drivers/hwmon/lm83.c b/drivers/hwmon/lm83.c
index feb87b4..654c0f7 100644
--- a/drivers/hwmon/lm83.c
+++ b/drivers/hwmon/lm83.c
@@ -223,14 +223,14 @@
 /* Individual alarm files */
 static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 0);
 static SENSOR_DEVICE_ATTR(temp3_crit_alarm, S_IRUGO, show_alarm, NULL, 1);
-static SENSOR_DEVICE_ATTR(temp3_input_fault, S_IRUGO, show_alarm, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_alarm, NULL, 2);
 static SENSOR_DEVICE_ATTR(temp3_max_alarm, S_IRUGO, show_alarm, NULL, 4);
 static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 6);
 static SENSOR_DEVICE_ATTR(temp2_crit_alarm, S_IRUGO, show_alarm, NULL, 8);
 static SENSOR_DEVICE_ATTR(temp4_crit_alarm, S_IRUGO, show_alarm, NULL, 9);
-static SENSOR_DEVICE_ATTR(temp4_input_fault, S_IRUGO, show_alarm, NULL, 10);
+static SENSOR_DEVICE_ATTR(temp4_fault, S_IRUGO, show_alarm, NULL, 10);
 static SENSOR_DEVICE_ATTR(temp4_max_alarm, S_IRUGO, show_alarm, NULL, 12);
-static SENSOR_DEVICE_ATTR(temp2_input_fault, S_IRUGO, show_alarm, NULL, 13);
+static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 13);
 static SENSOR_DEVICE_ATTR(temp2_max_alarm, S_IRUGO, show_alarm, NULL, 15);
 /* Raw alarm file for compatibility */
 static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
@@ -245,7 +245,7 @@
 
 	&sensor_dev_attr_temp1_crit_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp3_crit_alarm.dev_attr.attr,
-	&sensor_dev_attr_temp3_input_fault.dev_attr.attr,
+	&sensor_dev_attr_temp3_fault.dev_attr.attr,
 	&sensor_dev_attr_temp3_max_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
 	&dev_attr_alarms.attr,
@@ -266,9 +266,9 @@
 
 	&sensor_dev_attr_temp2_crit_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp4_crit_alarm.dev_attr.attr,
-	&sensor_dev_attr_temp4_input_fault.dev_attr.attr,
+	&sensor_dev_attr_temp4_fault.dev_attr.attr,
 	&sensor_dev_attr_temp4_max_alarm.dev_attr.attr,
-	&sensor_dev_attr_temp2_input_fault.dev_attr.attr,
+	&sensor_dev_attr_temp2_fault.dev_attr.attr,
 	&sensor_dev_attr_temp2_max_alarm.dev_attr.attr,
 	NULL
 };
diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c
index 6882ce7..48833ff 100644
--- a/drivers/hwmon/lm90.c
+++ b/drivers/hwmon/lm90.c
@@ -43,6 +43,13 @@
  * variants. The extra address and features of the MAX6659 are not
  * supported by this driver.
  *
+ * This driver also supports the MAX6680 and MAX6681, two other sensor
+ * chips made by Maxim. These are quite similar to the other Maxim
+ * chips. Complete datasheet can be obtained at:
+ *   http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3370
+ * The MAX6680 and MAX6681 only differ in the pinout so they can be
+ * treated identically.
+ *
  * This driver also supports the ADT7461 chip from Analog Devices but
  * only in its "compatability mode". If an ADT7461 chip is found but
  * is configured in non-compatible mode (where its temperature
@@ -84,20 +91,25 @@
 /*
  * Addresses to scan
  * Address is fully defined internally and cannot be changed except for
- * MAX6659.
+ * MAX6659, MAX6680 and MAX6681.
  * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, MAX6657 and MAX6658
  * have address 0x4c.
  * ADM1032-2, ADT7461-2, LM89-1, and LM99-1 have address 0x4d.
  * MAX6659 can have address 0x4c, 0x4d or 0x4e (unsupported).
+ * MAX6680 and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
+ * 0x4c, 0x4d or 0x4e.
  */
 
-static unsigned short normal_i2c[] = { 0x4c, 0x4d, I2C_CLIENT_END };
+static unsigned short normal_i2c[] = { 0x18, 0x19, 0x1a,
+				       0x29, 0x2a, 0x2b,
+				       0x4c, 0x4d, 0x4e,
+				       I2C_CLIENT_END };
 
 /*
  * Insmod parameters
  */
 
-I2C_CLIENT_INSMOD_6(lm90, adm1032, lm99, lm86, max6657, adt7461);
+I2C_CLIENT_INSMOD_7(lm90, adm1032, lm99, lm86, max6657, adt7461, max6680);
 
 /*
  * The LM90 registers
@@ -359,7 +371,7 @@
 /* Individual alarm files */
 static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 0);
 static SENSOR_DEVICE_ATTR(temp2_crit_alarm, S_IRUGO, show_alarm, NULL, 1);
-static SENSOR_DEVICE_ATTR(temp2_input_fault, S_IRUGO, show_alarm, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 2);
 static SENSOR_DEVICE_ATTR(temp2_min_alarm, S_IRUGO, show_alarm, NULL, 3);
 static SENSOR_DEVICE_ATTR(temp2_max_alarm, S_IRUGO, show_alarm, NULL, 4);
 static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL, 5);
@@ -381,7 +393,7 @@
 
 	&sensor_dev_attr_temp1_crit_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp2_crit_alarm.dev_attr.attr,
-	&sensor_dev_attr_temp2_input_fault.dev_attr.attr,
+	&sensor_dev_attr_temp2_fault.dev_attr.attr,
 	&sensor_dev_attr_temp2_min_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp2_max_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
@@ -429,7 +441,7 @@
  */
 
 /* The ADM1032 supports PEC but not on write byte transactions, so we need
-   to explicitely ask for a transaction without PEC. */
+   to explicitly ask for a transaction without PEC. */
 static inline s32 adm1032_write_byte(struct i2c_client *client, u8 value)
 {
 	return i2c_smbus_xfer(client->adapter, client->addr,
@@ -525,7 +537,8 @@
 		 		  &reg_convrate) < 0)
 			goto exit_free;
 		
-		if (man_id == 0x01) { /* National Semiconductor */
+		if ((address == 0x4C || address == 0x4D)
+		 && man_id == 0x01) { /* National Semiconductor */
 			u8 reg_config2;
 
 			if (lm90_read_reg(new_client, LM90_REG_R_CONFIG2,
@@ -548,7 +561,8 @@
 				}
 			}
 		} else
-		if (man_id == 0x41) { /* Analog Devices */
+		if ((address == 0x4C || address == 0x4D)
+		 && man_id == 0x41) { /* Analog Devices */
 			if ((chip_id & 0xF0) == 0x40 /* ADM1032 */
 			 && (reg_config1 & 0x3F) == 0x00
 			 && reg_convrate <= 0x0A) {
@@ -562,18 +576,30 @@
 		} else
 		if (man_id == 0x4D) { /* Maxim */
 			/*
-			 * The Maxim variants do NOT have a chip_id register.
-			 * Reading from that address will return the last read
-			 * value, which in our case is those of the man_id
-			 * register. Likewise, the config1 register seems to
-			 * lack a low nibble, so the value will be those of the
-			 * previous read, so in our case those of the man_id
-			 * register.
+			 * The MAX6657, MAX6658 and MAX6659 do NOT have a
+			 * chip_id register. Reading from that address will
+			 * return the last read value, which in our case is
+			 * those of the man_id register. Likewise, the config1
+			 * register seems to lack a low nibble, so the value
+			 * will be those of the previous read, so in our case
+			 * those of the man_id register.
 			 */
 			if (chip_id == man_id
+			 && (address == 0x4F || address == 0x4D)
 			 && (reg_config1 & 0x1F) == (man_id & 0x0F)
 			 && reg_convrate <= 0x09) {
 			 	kind = max6657;
+			} else
+			/* The chip_id register of the MAX6680 and MAX6681
+			 * holds the revision of the chip.
+			 * the lowest bit of the config1 register is unused
+			 * and should return zero when read, so should the
+			 * second to last bit of config1 (software reset)
+			 */
+			if (chip_id == 0x01
+			 && (reg_config1 & 0x03) == 0x00
+			 && reg_convrate <= 0x07) {
+			 	kind = max6680;
 			}
 		}
 
@@ -599,6 +625,8 @@
 		name = "lm86";
 	} else if (kind == max6657) {
 		name = "max6657";
+	} else if (kind == max6680) {
+		name = "max6680";
 	} else if (kind == adt7461) {
 		name = "adt7461";
 	}
@@ -646,7 +674,8 @@
 
 static void lm90_init_client(struct i2c_client *client)
 {
-	u8 config;
+	u8 config, config_orig;
+	struct lm90_data *data = i2c_get_clientdata(client);
 
 	/*
 	 * Start the conversions.
@@ -657,9 +686,20 @@
 		dev_warn(&client->dev, "Initialization failed!\n");
 		return;
 	}
-	if (config & 0x40)
-		i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1,
-					  config & 0xBF); /* run */
+	config_orig = config;
+
+	/*
+	 * Put MAX6680/MAX8881 into extended resolution (bit 0x10,
+	 * 0.125 degree resolution) and range (0x08, extend range
+	 * to -64 degree) mode for the remote temperature sensor.
+	 */
+	if (data->kind == max6680) {
+		config |= 0x18;
+	}
+
+	config &= 0xBF;	/* run */
+	if (config != config_orig) /* Only write if changed */
+		i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, config);
 }
 
 static int lm90_detach_client(struct i2c_client *client)
diff --git a/drivers/hwmon/lm93.c b/drivers/hwmon/lm93.c
new file mode 100644
index 0000000..23edf4f
--- /dev/null
+++ b/drivers/hwmon/lm93.c
@@ -0,0 +1,2655 @@
+/*
+    lm93.c - Part of lm_sensors, Linux kernel modules for hardware monitoring
+
+    Author/Maintainer: Mark M. Hoffman <mhoffman@lightlink.com>
+	Copyright (c) 2004 Utilitek Systems, Inc.
+
+    derived in part from lm78.c:
+	Copyright (c) 1998, 1999  Frodo Looijaard <frodol@dds.nl>
+
+    derived in part from lm85.c:
+	Copyright (c) 2002, 2003 Philip Pokorny <ppokorny@penguincomputing.com>
+	Copyright (c) 2003       Margit Schubert-While <margitsw@t-online.de>
+
+    derived in part from w83l785ts.c:
+	Copyright (c) 2003-2004 Jean Delvare <khali@linux-fr.org>
+
+    Ported to Linux 2.6 by Eric J. Bowersox <ericb@aspsys.com>
+	Copyright (c) 2005 Aspen Systems, Inc.
+
+    Adapted to 2.6.20 by Carsten Emde <cbe@osadl.org>
+        Copyright (c) 2006 Carsten Emde, Open Source Automation Development Lab
+
+    Modified for mainline integration by Hans J. Koch <hjk@linutronix.de>
+        Copyright (c) 2007 Hans J. Koch, Linutronix GmbH
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation; either version 2 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program; if not, write to the Free Software
+    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/hwmon-vid.h>
+#include <linux/err.h>
+#include <linux/delay.h>
+
+/* LM93 REGISTER ADDRESSES */
+
+/* miscellaneous */
+#define LM93_REG_MFR_ID			0x3e
+#define LM93_REG_VER			0x3f
+#define LM93_REG_STATUS_CONTROL		0xe2
+#define LM93_REG_CONFIG			0xe3
+#define LM93_REG_SLEEP_CONTROL		0xe4
+
+/* alarm values start here */
+#define LM93_REG_HOST_ERROR_1		0x48
+
+/* voltage inputs: in1-in16 (nr => 0-15) */
+#define LM93_REG_IN(nr)			(0x56 + (nr))
+#define LM93_REG_IN_MIN(nr)		(0x90 + (nr) * 2)
+#define LM93_REG_IN_MAX(nr)		(0x91 + (nr) * 2)
+
+/* temperature inputs: temp1-temp4 (nr => 0-3) */
+#define LM93_REG_TEMP(nr)		(0x50 + (nr))
+#define LM93_REG_TEMP_MIN(nr)		(0x78 + (nr) * 2)
+#define LM93_REG_TEMP_MAX(nr)		(0x79 + (nr) * 2)
+
+/* temp[1-4]_auto_boost (nr => 0-3) */
+#define LM93_REG_BOOST(nr)		(0x80 + (nr))
+
+/* #PROCHOT inputs: prochot1-prochot2 (nr => 0-1) */
+#define LM93_REG_PROCHOT_CUR(nr)	(0x67 + (nr) * 2)
+#define LM93_REG_PROCHOT_AVG(nr)	(0x68 + (nr) * 2)
+#define LM93_REG_PROCHOT_MAX(nr)	(0xb0 + (nr))
+
+/* fan tach inputs: fan1-fan4 (nr => 0-3) */
+#define LM93_REG_FAN(nr)		(0x6e + (nr) * 2)
+#define LM93_REG_FAN_MIN(nr)		(0xb4 + (nr) * 2)
+
+/* pwm outputs: pwm1-pwm2 (nr => 0-1, reg => 0-3) */
+#define LM93_REG_PWM_CTL(nr,reg)	(0xc8 + (reg) + (nr) * 4)
+#define LM93_PWM_CTL1	0x0
+#define LM93_PWM_CTL2	0x1
+#define LM93_PWM_CTL3	0x2
+#define LM93_PWM_CTL4	0x3
+
+/* GPIO input state */
+#define LM93_REG_GPI			0x6b
+
+/* vid inputs: vid1-vid2 (nr => 0-1) */
+#define LM93_REG_VID(nr)		(0x6c + (nr))
+
+/* vccp1 & vccp2: VID relative inputs (nr => 0-1) */
+#define LM93_REG_VCCP_LIMIT_OFF(nr)	(0xb2 + (nr))
+
+/* temp[1-4]_auto_boost_hyst */
+#define LM93_REG_BOOST_HYST_12		0xc0
+#define LM93_REG_BOOST_HYST_34		0xc1
+#define LM93_REG_BOOST_HYST(nr)		(0xc0 + (nr)/2)
+
+/* temp[1-4]_auto_pwm_[min|hyst] */
+#define LM93_REG_PWM_MIN_HYST_12	0xc3
+#define LM93_REG_PWM_MIN_HYST_34	0xc4
+#define LM93_REG_PWM_MIN_HYST(nr)	(0xc3 + (nr)/2)
+
+/* prochot_override & prochot_interval */
+#define LM93_REG_PROCHOT_OVERRIDE	0xc6
+#define LM93_REG_PROCHOT_INTERVAL	0xc7
+
+/* temp[1-4]_auto_base (nr => 0-3) */
+#define LM93_REG_TEMP_BASE(nr)		(0xd0 + (nr))
+
+/* temp[1-4]_auto_offsets (step => 0-11) */
+#define LM93_REG_TEMP_OFFSET(step)	(0xd4 + (step))
+
+/* #PROCHOT & #VRDHOT PWM ramp control */
+#define LM93_REG_PWM_RAMP_CTL		0xbf
+
+/* miscellaneous */
+#define LM93_REG_SFC1		0xbc
+#define LM93_REG_SFC2		0xbd
+#define LM93_REG_GPI_VID_CTL	0xbe
+#define LM93_REG_SF_TACH_TO_PWM	0xe0
+
+/* error masks */
+#define LM93_REG_GPI_ERR_MASK	0xec
+#define LM93_REG_MISC_ERR_MASK	0xed
+
+/* LM93 REGISTER VALUES */
+#define LM93_MFR_ID		0x73
+#define LM93_MFR_ID_PROTOTYPE	0x72
+
+/* SMBus capabilities */
+#define LM93_SMBUS_FUNC_FULL (I2C_FUNC_SMBUS_BYTE_DATA | \
+		I2C_FUNC_SMBUS_WORD_DATA | I2C_FUNC_SMBUS_BLOCK_DATA)
+#define LM93_SMBUS_FUNC_MIN  (I2C_FUNC_SMBUS_BYTE_DATA | \
+		I2C_FUNC_SMBUS_WORD_DATA)
+
+/* Addresses to scan */
+static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
+
+/* Insmod parameters */
+I2C_CLIENT_INSMOD_1(lm93);
+
+static int disable_block;
+module_param(disable_block, bool, 0);
+MODULE_PARM_DESC(disable_block,
+	"Set to non-zero to disable SMBus block data transactions.");
+
+static int init;
+module_param(init, bool, 0);
+MODULE_PARM_DESC(init, "Set to non-zero to force chip initialization.");
+
+static int vccp_limit_type[2] = {0,0};
+module_param_array(vccp_limit_type, int, NULL, 0);
+MODULE_PARM_DESC(vccp_limit_type, "Configures in7 and in8 limit modes.");
+
+static int vid_agtl;
+module_param(vid_agtl, int, 0);
+MODULE_PARM_DESC(vid_agtl, "Configures VID pin input thresholds.");
+
+/* Driver data */
+static struct i2c_driver lm93_driver;
+
+/* LM93 BLOCK READ COMMANDS */
+static const struct { u8 cmd; u8 len; } lm93_block_read_cmds[12] = {
+	{ 0xf2,  8 },
+	{ 0xf3,  8 },
+	{ 0xf4,  6 },
+	{ 0xf5, 16 },
+	{ 0xf6,  4 },
+	{ 0xf7,  8 },
+	{ 0xf8, 12 },
+	{ 0xf9, 32 },
+	{ 0xfa,  8 },
+	{ 0xfb,  8 },
+	{ 0xfc, 16 },
+	{ 0xfd,  9 },
+};
+
+/* ALARMS: SYSCTL format described further below
+   REG: 64 bits in 8 registers, as immediately below */
+struct block1_t {
+	u8 host_status_1;
+	u8 host_status_2;
+	u8 host_status_3;
+	u8 host_status_4;
+	u8 p1_prochot_status;
+	u8 p2_prochot_status;
+	u8 gpi_status;
+	u8 fan_status;
+};
+
+/*
+ * Client-specific data
+ */
+struct lm93_data {
+	struct i2c_client client;
+	struct class_device *class_dev;
+
+	struct mutex update_lock;
+	unsigned long last_updated;	/* In jiffies */
+
+	/* client update function */
+	void (*update)(struct lm93_data *, struct i2c_client *);
+
+	char valid; /* !=0 if following fields are valid */
+
+	/* register values, arranged by block read groups */
+	struct block1_t block1;
+
+	/* temp1 - temp4: unfiltered readings
+	   temp1 - temp2: filtered readings */
+	u8 block2[6];
+
+	/* vin1 - vin16: readings */
+	u8 block3[16];
+
+	/* prochot1 - prochot2: readings */
+	struct {
+		u8 cur;
+		u8 avg;
+	} block4[2];
+
+	/* fan counts 1-4 => 14-bits, LE, *left* justified */
+	u16 block5[4];
+
+	/* block6 has a lot of data we don't need */
+	struct {
+		u8 min;
+		u8 max;
+	} temp_lim[3];
+
+	/* vin1 - vin16: low and high limits */
+	struct {
+		u8 min;
+		u8 max;
+	} block7[16];
+
+	/* fan count limits 1-4 => same format as block5 */
+	u16 block8[4];
+
+	/* pwm control registers (2 pwms, 4 regs) */
+	u8 block9[2][4];
+
+	/* auto/pwm base temp and offset temp registers */
+	struct {
+		u8 base[4];
+		u8 offset[12];
+	} block10;
+
+	/* master config register */
+	u8 config;
+
+	/* VID1 & VID2 => register format, 6-bits, right justified */
+	u8 vid[2];
+
+	/* prochot1 - prochot2: limits */
+	u8 prochot_max[2];
+
+	/* vccp1 & vccp2 (in7 & in8): VID relative limits (register format) */
+	u8 vccp_limits[2];
+
+	/* GPIO input state (register format, i.e. inverted) */
+	u8 gpi;
+
+	/* #PROCHOT override (register format) */
+	u8 prochot_override;
+
+	/* #PROCHOT intervals (register format) */
+	u8 prochot_interval;
+
+	/* Fan Boost Temperatures (register format) */
+	u8 boost[4];
+
+	/* Fan Boost Hysteresis (register format) */
+	u8 boost_hyst[2];
+
+	/* Temperature Zone Min. PWM & Hysteresis (register format) */
+	u8 auto_pwm_min_hyst[2];
+
+	/* #PROCHOT & #VRDHOT PWM Ramp Control */
+	u8 pwm_ramp_ctl;
+
+	/* miscellaneous setup regs */
+	u8 sfc1;
+	u8 sfc2;
+	u8 sf_tach_to_pwm;
+
+	/* The two PWM CTL2  registers can read something other than what was
+	   last written for the OVR_DC field (duty cycle override).  So, we
+	   save the user-commanded value here. */
+	u8 pwm_override[2];
+};
+
+/* VID:	mV
+   REG: 6-bits, right justified, *always* using Intel VRM/VRD 10 */
+static int LM93_VID_FROM_REG(u8 reg)
+{
+	return vid_from_reg((reg & 0x3f), 100);
+}
+
+/* min, max, and nominal register values, per channel (u8) */
+static const u8 lm93_vin_reg_min[16] = {
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xae,
+};
+static const u8 lm93_vin_reg_max[16] = {
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+	0xff, 0xfa, 0xff, 0xff, 0xff, 0xff, 0xff, 0xd1,
+};
+/* Values from the datasheet. They're here for documentation only.
+static const u8 lm93_vin_reg_nom[16] = {
+	0xc0, 0xc0, 0xc0, 0xc0, 0xc0, 0xc0, 0xc0, 0xc0,
+	0xc0, 0xc0, 0xc0, 0xc0, 0xc0, 0xc0, 0x40, 0xc0,
+};
+*/
+
+/* min, max, and nominal voltage readings, per channel (mV)*/
+static const unsigned long lm93_vin_val_min[16] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 3000,
+};
+
+static const unsigned long lm93_vin_val_max[16] = {
+	1236, 1236, 1236, 1600, 2000, 2000, 1600, 1600,
+	4400, 6500, 3333, 2625, 1312, 1312, 1236, 3600,
+};
+/* Values from the datasheet. They're here for documentation only.
+static const unsigned long lm93_vin_val_nom[16] = {
+	 927,  927,  927, 1200, 1500, 1500, 1200, 1200,
+	3300, 5000, 2500, 1969,  984,  984,  309, 3300,
+};
+*/
+
+static unsigned LM93_IN_FROM_REG(int nr, u8 reg)
+{
+	const long uV_max = lm93_vin_val_max[nr] * 1000;
+	const long uV_min = lm93_vin_val_min[nr] * 1000;
+
+	const long slope = (uV_max - uV_min) /
+		(lm93_vin_reg_max[nr] - lm93_vin_reg_min[nr]);
+	const long intercept = uV_min - slope * lm93_vin_reg_min[nr];
+
+	return (slope * reg + intercept + 500) / 1000;
+}
+
+/* IN: mV, limits determined by channel nr
+   REG: scaling determined by channel nr */
+static u8 LM93_IN_TO_REG(int nr, unsigned val)
+{
+	/* range limit */
+	const long mV = SENSORS_LIMIT(val,
+		lm93_vin_val_min[nr], lm93_vin_val_max[nr]);
+
+	/* try not to lose too much precision here */
+	const long uV = mV * 1000;
+	const long uV_max = lm93_vin_val_max[nr] * 1000;
+	const long uV_min = lm93_vin_val_min[nr] * 1000;
+
+	/* convert */
+	const long slope = (uV_max - uV_min) /
+		(lm93_vin_reg_max[nr] - lm93_vin_reg_min[nr]);
+	const long intercept = uV_min - slope * lm93_vin_reg_min[nr];
+
+	u8 result = ((uV - intercept + (slope/2)) / slope);
+	result = SENSORS_LIMIT(result,
+			lm93_vin_reg_min[nr], lm93_vin_reg_max[nr]);
+	return result;
+}
+
+/* vid in mV, upper == 0 indicates low limit, otherwise upper limit */
+static unsigned LM93_IN_REL_FROM_REG(u8 reg, int upper, int vid)
+{
+	const long uV_offset = upper ? (((reg >> 4 & 0x0f) + 1) * 12500) :
+				(((reg >> 0 & 0x0f) + 1) * -25000);
+	const long uV_vid = vid * 1000;
+	return (uV_vid + uV_offset + 5000) / 10000;
+}
+
+#define LM93_IN_MIN_FROM_REG(reg,vid)	LM93_IN_REL_FROM_REG(reg,0,vid)
+#define LM93_IN_MAX_FROM_REG(reg,vid)	LM93_IN_REL_FROM_REG(reg,1,vid)
+
+/* vid in mV , upper == 0 indicates low limit, otherwise upper limit
+   upper also determines which nibble of the register is returned
+   (the other nibble will be 0x0) */
+static u8 LM93_IN_REL_TO_REG(unsigned val, int upper, int vid)
+{
+	long uV_offset = vid * 1000 - val * 10000;
+	if (upper) {
+		uV_offset = SENSORS_LIMIT(uV_offset, 12500, 200000);
+		return (u8)((uV_offset /  12500 - 1) << 4);
+	} else {
+		uV_offset = SENSORS_LIMIT(uV_offset, -400000, -25000);
+		return (u8)((uV_offset / -25000 - 1) << 0);
+	}
+}
+
+/* TEMP: 1/1000 degrees C (-128C to +127C)
+   REG: 1C/bit, two's complement */
+static int LM93_TEMP_FROM_REG(u8 reg)
+{
+	return (s8)reg * 1000;
+}
+
+#define LM93_TEMP_MIN (-128000)
+#define LM93_TEMP_MAX ( 127000)
+
+/* TEMP: 1/1000 degrees C (-128C to +127C)
+   REG: 1C/bit, two's complement */
+static u8 LM93_TEMP_TO_REG(int temp)
+{
+	int ntemp = SENSORS_LIMIT(temp, LM93_TEMP_MIN, LM93_TEMP_MAX);
+	ntemp += (ntemp<0 ? -500 : 500);
+	return (u8)(ntemp / 1000);
+}
+
+/* Determine 4-bit temperature offset resolution */
+static int LM93_TEMP_OFFSET_MODE_FROM_REG(u8 sfc2, int nr)
+{
+	/* mode: 0 => 1C/bit, nonzero => 0.5C/bit */
+	return sfc2 & (nr < 2 ? 0x10 : 0x20);
+}
+
+/* This function is common to all 4-bit temperature offsets
+   reg is 4 bits right justified
+   mode 0 => 1C/bit, mode !0 => 0.5C/bit */
+static int LM93_TEMP_OFFSET_FROM_REG(u8 reg, int mode)
+{
+	return (reg & 0x0f) * (mode ? 5 : 10);
+}
+
+#define LM93_TEMP_OFFSET_MIN  (  0)
+#define LM93_TEMP_OFFSET_MAX0 (150)
+#define LM93_TEMP_OFFSET_MAX1 ( 75)
+
+/* This function is common to all 4-bit temperature offsets
+   returns 4 bits right justified
+   mode 0 => 1C/bit, mode !0 => 0.5C/bit */
+static u8 LM93_TEMP_OFFSET_TO_REG(int off, int mode)
+{
+	int factor = mode ? 5 : 10;
+
+	off = SENSORS_LIMIT(off, LM93_TEMP_OFFSET_MIN,
+		mode ? LM93_TEMP_OFFSET_MAX1 : LM93_TEMP_OFFSET_MAX0);
+	return (u8)((off + factor/2) / factor);
+}
+
+/* 0 <= nr <= 3 */
+static int LM93_TEMP_AUTO_OFFSET_FROM_REG(u8 reg, int nr, int mode)
+{
+	/* temp1-temp2 (nr=0,1) use lower nibble */
+	if (nr < 2)
+		return LM93_TEMP_OFFSET_FROM_REG(reg & 0x0f, mode);
+
+	/* temp3-temp4 (nr=2,3) use upper nibble */
+	else
+		return LM93_TEMP_OFFSET_FROM_REG(reg >> 4 & 0x0f, mode);
+}
+
+/* TEMP: 1/10 degrees C (0C to +15C (mode 0) or +7.5C (mode non-zero))
+   REG: 1.0C/bit (mode 0) or 0.5C/bit (mode non-zero)
+   0 <= nr <= 3 */
+static u8 LM93_TEMP_AUTO_OFFSET_TO_REG(u8 old, int off, int nr, int mode)
+{
+	u8 new = LM93_TEMP_OFFSET_TO_REG(off, mode);
+
+	/* temp1-temp2 (nr=0,1) use lower nibble */
+	if (nr < 2)
+		return (old & 0xf0) | (new & 0x0f);
+
+	/* temp3-temp4 (nr=2,3) use upper nibble */
+	else
+		return (new << 4 & 0xf0) | (old & 0x0f);
+}
+
+static int LM93_AUTO_BOOST_HYST_FROM_REGS(struct lm93_data *data, int nr,
+		int mode)
+{
+	u8 reg;
+
+	switch (nr) {
+	case 0:
+		reg = data->boost_hyst[0] & 0x0f;
+		break;
+	case 1:
+		reg = data->boost_hyst[0] >> 4 & 0x0f;
+		break;
+	case 2:
+		reg = data->boost_hyst[1] & 0x0f;
+		break;
+	case 3:
+	default:
+		reg = data->boost_hyst[1] >> 4 & 0x0f;
+		break;
+	}
+
+	return LM93_TEMP_FROM_REG(data->boost[nr]) -
+			LM93_TEMP_OFFSET_FROM_REG(reg, mode);
+}
+
+static u8 LM93_AUTO_BOOST_HYST_TO_REG(struct lm93_data *data, long hyst,
+		int nr, int mode)
+{
+	u8 reg = LM93_TEMP_OFFSET_TO_REG(
+			(LM93_TEMP_FROM_REG(data->boost[nr]) - hyst), mode);
+
+	switch (nr) {
+	case 0:
+		reg = (data->boost_hyst[0] & 0xf0) | (reg & 0x0f);
+		break;
+	case 1:
+		reg = (reg << 4 & 0xf0) | (data->boost_hyst[0] & 0x0f);
+		break;
+	case 2:
+		reg = (data->boost_hyst[1] & 0xf0) | (reg & 0x0f);
+		break;
+	case 3:
+	default:
+		reg = (reg << 4 & 0xf0) | (data->boost_hyst[1] & 0x0f);
+		break;
+	}
+
+	return reg;
+}
+
+/* PWM: 0-255 per sensors documentation
+   REG: 0-13 as mapped below... right justified */
+typedef enum { LM93_PWM_MAP_HI_FREQ, LM93_PWM_MAP_LO_FREQ } pwm_freq_t;
+static int lm93_pwm_map[2][16] = {
+	{
+		0x00, /*   0.00% */ 0x40, /*  25.00% */
+		0x50, /*  31.25% */ 0x60, /*  37.50% */
+		0x70, /*  43.75% */ 0x80, /*  50.00% */
+		0x90, /*  56.25% */ 0xa0, /*  62.50% */
+		0xb0, /*  68.75% */ 0xc0, /*  75.00% */
+		0xd0, /*  81.25% */ 0xe0, /*  87.50% */
+		0xf0, /*  93.75% */ 0xff, /* 100.00% */
+		0xff, 0xff, /* 14, 15 are reserved and should never occur */
+	},
+	{
+		0x00, /*   0.00% */ 0x40, /*  25.00% */
+		0x49, /*  28.57% */ 0x52, /*  32.14% */
+		0x5b, /*  35.71% */ 0x64, /*  39.29% */
+		0x6d, /*  42.86% */ 0x76, /*  46.43% */
+		0x80, /*  50.00% */ 0x89, /*  53.57% */
+		0x92, /*  57.14% */ 0xb6, /*  71.43% */
+		0xdb, /*  85.71% */ 0xff, /* 100.00% */
+		0xff, 0xff, /* 14, 15 are reserved and should never occur */
+	},
+};
+
+static int LM93_PWM_FROM_REG(u8 reg, pwm_freq_t freq)
+{
+	return lm93_pwm_map[freq][reg & 0x0f];
+}
+
+/* round up to nearest match */
+static u8 LM93_PWM_TO_REG(int pwm, pwm_freq_t freq)
+{
+	int i;
+	for (i = 0; i < 13; i++)
+		if (pwm <= lm93_pwm_map[freq][i])
+			break;
+
+	/* can fall through with i==13 */
+	return (u8)i;
+}
+
+static int LM93_FAN_FROM_REG(u16 regs)
+{
+	const u16 count = le16_to_cpu(regs) >> 2;
+	return count==0 ? -1 : count==0x3fff ? 0: 1350000 / count;
+}
+
+/*
+ * RPM: (82.5 to 1350000)
+ * REG: 14-bits, LE, *left* justified
+ */
+static u16 LM93_FAN_TO_REG(long rpm)
+{
+	u16 count, regs;
+
+	if (rpm == 0) {
+		count = 0x3fff;
+	} else {
+		rpm = SENSORS_LIMIT(rpm, 1, 1000000);
+		count = SENSORS_LIMIT((1350000 + rpm) / rpm, 1, 0x3ffe);
+	}
+
+	regs = count << 2;
+	return cpu_to_le16(regs);
+}
+
+/* PWM FREQ: HZ
+   REG: 0-7 as mapped below */
+static int lm93_pwm_freq_map[8] = {
+	22500, 96, 84, 72, 60, 48, 36, 12
+};
+
+static int LM93_PWM_FREQ_FROM_REG(u8 reg)
+{
+	return lm93_pwm_freq_map[reg & 0x07];
+}
+
+/* round up to nearest match */
+static u8 LM93_PWM_FREQ_TO_REG(int freq)
+{
+	int i;
+	for (i = 7; i > 0; i--)
+		if (freq <= lm93_pwm_freq_map[i])
+			break;
+
+	/* can fall through with i==0 */
+	return (u8)i;
+}
+
+/* TIME: 1/100 seconds
+ * REG: 0-7 as mapped below */
+static int lm93_spinup_time_map[8] = {
+	0, 10, 25, 40, 70, 100, 200, 400,
+};
+
+static int LM93_SPINUP_TIME_FROM_REG(u8 reg)
+{
+	return lm93_spinup_time_map[reg >> 5 & 0x07];
+}
+
+/* round up to nearest match */
+static u8 LM93_SPINUP_TIME_TO_REG(int time)
+{
+	int i;
+	for (i = 0; i < 7; i++)
+		if (time <= lm93_spinup_time_map[i])
+			break;
+
+	/* can fall through with i==8 */
+	return (u8)i;
+}
+
+#define LM93_RAMP_MIN 0
+#define LM93_RAMP_MAX 75
+
+static int LM93_RAMP_FROM_REG(u8 reg)
+{
+	return (reg & 0x0f) * 5;
+}
+
+/* RAMP: 1/100 seconds
+   REG: 50mS/bit 4-bits right justified */
+static u8 LM93_RAMP_TO_REG(int ramp)
+{
+	ramp = SENSORS_LIMIT(ramp, LM93_RAMP_MIN, LM93_RAMP_MAX);
+	return (u8)((ramp + 2) / 5);
+}
+
+/* PROCHOT: 0-255, 0 => 0%, 255 => > 96.6%
+ * REG: (same) */
+static u8 LM93_PROCHOT_TO_REG(long prochot)
+{
+	prochot = SENSORS_LIMIT(prochot, 0, 255);
+	return (u8)prochot;
+}
+
+/* PROCHOT-INTERVAL: 73 - 37200 (1/100 seconds)
+ * REG: 0-9 as mapped below */
+static int lm93_interval_map[10] = {
+	73, 146, 290, 580, 1170, 2330, 4660, 9320, 18600, 37200,
+};
+
+static int LM93_INTERVAL_FROM_REG(u8 reg)
+{
+	return lm93_interval_map[reg & 0x0f];
+}
+
+/* round up to nearest match */
+static u8 LM93_INTERVAL_TO_REG(long interval)
+{
+	int i;
+	for (i = 0; i < 9; i++)
+		if (interval <= lm93_interval_map[i])
+			break;
+
+	/* can fall through with i==9 */
+	return (u8)i;
+}
+
+/* GPIO: 0-255, GPIO0 is LSB
+ * REG: inverted */
+static unsigned LM93_GPI_FROM_REG(u8 reg)
+{
+	return ~reg & 0xff;
+}
+
+/* alarm bitmask definitions
+   The LM93 has nearly 64 bits of error status... I've pared that down to
+   what I think is a useful subset in order to fit it into 32 bits.
+
+   Especially note that the #VRD_HOT alarms are missing because we provide
+   that information as values in another sysfs file.
+
+   If libsensors is extended to support 64 bit values, this could be revisited.
+*/
+#define LM93_ALARM_IN1		0x00000001
+#define LM93_ALARM_IN2		0x00000002
+#define LM93_ALARM_IN3		0x00000004
+#define LM93_ALARM_IN4		0x00000008
+#define LM93_ALARM_IN5		0x00000010
+#define LM93_ALARM_IN6		0x00000020
+#define LM93_ALARM_IN7		0x00000040
+#define LM93_ALARM_IN8		0x00000080
+#define LM93_ALARM_IN9		0x00000100
+#define LM93_ALARM_IN10		0x00000200
+#define LM93_ALARM_IN11		0x00000400
+#define LM93_ALARM_IN12		0x00000800
+#define LM93_ALARM_IN13		0x00001000
+#define LM93_ALARM_IN14		0x00002000
+#define LM93_ALARM_IN15		0x00004000
+#define LM93_ALARM_IN16		0x00008000
+#define LM93_ALARM_FAN1		0x00010000
+#define LM93_ALARM_FAN2		0x00020000
+#define LM93_ALARM_FAN3		0x00040000
+#define LM93_ALARM_FAN4		0x00080000
+#define LM93_ALARM_PH1_ERR	0x00100000
+#define LM93_ALARM_PH2_ERR	0x00200000
+#define LM93_ALARM_SCSI1_ERR	0x00400000
+#define LM93_ALARM_SCSI2_ERR	0x00800000
+#define LM93_ALARM_DVDDP1_ERR	0x01000000
+#define LM93_ALARM_DVDDP2_ERR	0x02000000
+#define LM93_ALARM_D1_ERR	0x04000000
+#define LM93_ALARM_D2_ERR	0x08000000
+#define LM93_ALARM_TEMP1	0x10000000
+#define LM93_ALARM_TEMP2	0x20000000
+#define LM93_ALARM_TEMP3	0x40000000
+
+static unsigned LM93_ALARMS_FROM_REG(struct block1_t b1)
+{
+	unsigned result;
+	result  = b1.host_status_2 & 0x3f;
+
+	if (vccp_limit_type[0])
+		result |= (b1.host_status_4 & 0x10) << 2;
+	else
+		result |= b1.host_status_2 & 0x40;
+
+	if (vccp_limit_type[1])
+		result |= (b1.host_status_4 & 0x20) << 2;
+	else
+		result |= b1.host_status_2 & 0x80;
+
+	result |= b1.host_status_3 << 8;
+	result |= (b1.fan_status & 0x0f) << 16;
+	result |= (b1.p1_prochot_status & 0x80) << 13;
+	result |= (b1.p2_prochot_status & 0x80) << 14;
+	result |= (b1.host_status_4 & 0xfc) << 20;
+	result |= (b1.host_status_1 & 0x07) << 28;
+	return result;
+}
+
+#define MAX_RETRIES 5
+
+static u8 lm93_read_byte(struct i2c_client *client, u8 reg)
+{
+	int value, i;
+
+	/* retry in case of read errors */
+	for (i=1; i<=MAX_RETRIES; i++) {
+		if ((value = i2c_smbus_read_byte_data(client, reg)) >= 0) {
+			return value;
+		} else {
+			dev_warn(&client->dev,"lm93: read byte data failed, "
+				"address 0x%02x.\n", reg);
+			mdelay(i + 3);
+		}
+
+	}
+
+	/* <TODO> what to return in case of error? */
+	dev_err(&client->dev,"lm93: All read byte retries failed!!\n");
+	return 0;
+}
+
+static int lm93_write_byte(struct i2c_client *client, u8 reg, u8 value)
+{
+	int result;
+
+	/* <TODO> how to handle write errors? */
+	result = i2c_smbus_write_byte_data(client, reg, value);
+
+	if (result < 0)
+		dev_warn(&client->dev,"lm93: write byte data failed, "
+			 "0x%02x at address 0x%02x.\n", value, reg);
+
+	return result;
+}
+
+static u16 lm93_read_word(struct i2c_client *client, u8 reg)
+{
+	int value, i;
+
+	/* retry in case of read errors */
+	for (i=1; i<=MAX_RETRIES; i++) {
+		if ((value = i2c_smbus_read_word_data(client, reg)) >= 0) {
+			return value;
+		} else {
+			dev_warn(&client->dev,"lm93: read word data failed, "
+				 "address 0x%02x.\n", reg);
+			mdelay(i + 3);
+		}
+
+	}
+
+	/* <TODO> what to return in case of error? */
+	dev_err(&client->dev,"lm93: All read word retries failed!!\n");
+	return 0;
+}
+
+static int lm93_write_word(struct i2c_client *client, u8 reg, u16 value)
+{
+	int result;
+
+	/* <TODO> how to handle write errors? */
+	result = i2c_smbus_write_word_data(client, reg, value);
+
+	if (result < 0)
+		dev_warn(&client->dev,"lm93: write word data failed, "
+			 "0x%04x at address 0x%02x.\n", value, reg);
+
+	return result;
+}
+
+static u8 lm93_block_buffer[I2C_SMBUS_BLOCK_MAX];
+
+/*
+	read block data into values, retry if not expected length
+	fbn => index to lm93_block_read_cmds table
+		(Fixed Block Number - section 14.5.2 of LM93 datasheet)
+*/
+static void lm93_read_block(struct i2c_client *client, u8 fbn, u8 *values)
+{
+	int i, result=0;
+
+	for (i = 1; i <= MAX_RETRIES; i++) {
+		result = i2c_smbus_read_block_data(client,
+			lm93_block_read_cmds[fbn].cmd, lm93_block_buffer);
+
+		if (result == lm93_block_read_cmds[fbn].len) {
+			break;
+		} else {
+			dev_warn(&client->dev,"lm93: block read data failed, "
+				 "command 0x%02x.\n",
+				 lm93_block_read_cmds[fbn].cmd);
+			mdelay(i + 3);
+		}
+	}
+
+	if (result == lm93_block_read_cmds[fbn].len) {
+		memcpy(values,lm93_block_buffer,lm93_block_read_cmds[fbn].len);
+	} else {
+		/* <TODO> what to do in case of error? */
+	}
+}
+
+static struct lm93_data *lm93_update_device(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	const unsigned long interval = HZ + (HZ / 2);
+
+	mutex_lock(&data->update_lock);
+
+	if (time_after(jiffies, data->last_updated + interval) ||
+		!data->valid) {
+
+		data->update(data, client);
+		data->last_updated = jiffies;
+		data->valid = 1;
+	}
+
+	mutex_unlock(&data->update_lock);
+	return data;
+}
+
+/* update routine for data that has no corresponding SMBus block command */
+static void lm93_update_client_common(struct lm93_data *data,
+				      struct i2c_client *client)
+{
+	int i;
+	u8 *ptr;
+
+	/* temp1 - temp4: limits */
+	for (i = 0; i < 4; i++) {
+		data->temp_lim[i].min =
+			lm93_read_byte(client, LM93_REG_TEMP_MIN(i));
+		data->temp_lim[i].max =
+			lm93_read_byte(client, LM93_REG_TEMP_MAX(i));
+	}
+
+	/* config register */
+	data->config = lm93_read_byte(client, LM93_REG_CONFIG);
+
+	/* vid1 - vid2: values */
+	for (i = 0; i < 2; i++)
+		data->vid[i] = lm93_read_byte(client, LM93_REG_VID(i));
+
+	/* prochot1 - prochot2: limits */
+	for (i = 0; i < 2; i++)
+		data->prochot_max[i] = lm93_read_byte(client,
+				LM93_REG_PROCHOT_MAX(i));
+
+	/* vccp1 - vccp2: VID relative limits */
+	for (i = 0; i < 2; i++)
+		data->vccp_limits[i] = lm93_read_byte(client,
+				LM93_REG_VCCP_LIMIT_OFF(i));
+
+	/* GPIO input state */
+	data->gpi = lm93_read_byte(client, LM93_REG_GPI);
+
+	/* #PROCHOT override state */
+	data->prochot_override = lm93_read_byte(client,
+			LM93_REG_PROCHOT_OVERRIDE);
+
+	/* #PROCHOT intervals */
+	data->prochot_interval = lm93_read_byte(client,
+			LM93_REG_PROCHOT_INTERVAL);
+
+	/* Fan Boost Termperature registers */
+	for (i = 0; i < 4; i++)
+		data->boost[i] = lm93_read_byte(client, LM93_REG_BOOST(i));
+
+	/* Fan Boost Temperature Hyst. registers */
+	data->boost_hyst[0] = lm93_read_byte(client, LM93_REG_BOOST_HYST_12);
+	data->boost_hyst[1] = lm93_read_byte(client, LM93_REG_BOOST_HYST_34);
+
+	/* Temperature Zone Min. PWM & Hysteresis registers */
+	data->auto_pwm_min_hyst[0] =
+			lm93_read_byte(client, LM93_REG_PWM_MIN_HYST_12);
+	data->auto_pwm_min_hyst[1] =
+			lm93_read_byte(client, LM93_REG_PWM_MIN_HYST_34);
+
+	/* #PROCHOT & #VRDHOT PWM Ramp Control register */
+	data->pwm_ramp_ctl = lm93_read_byte(client, LM93_REG_PWM_RAMP_CTL);
+
+	/* misc setup registers */
+	data->sfc1 = lm93_read_byte(client, LM93_REG_SFC1);
+	data->sfc2 = lm93_read_byte(client, LM93_REG_SFC2);
+	data->sf_tach_to_pwm = lm93_read_byte(client,
+			LM93_REG_SF_TACH_TO_PWM);
+
+	/* write back alarm values to clear */
+	for (i = 0, ptr = (u8 *)(&data->block1); i < 8; i++)
+		lm93_write_byte(client, LM93_REG_HOST_ERROR_1 + i, *(ptr + i));
+}
+
+/* update routine which uses SMBus block data commands */
+static void lm93_update_client_full(struct lm93_data *data,
+				    struct i2c_client *client)
+{
+	dev_dbg(&client->dev,"starting device update (block data enabled)\n");
+
+	/* in1 - in16: values & limits */
+	lm93_read_block(client, 3, (u8 *)(data->block3));
+	lm93_read_block(client, 7, (u8 *)(data->block7));
+
+	/* temp1 - temp4: values */
+	lm93_read_block(client, 2, (u8 *)(data->block2));
+
+	/* prochot1 - prochot2: values */
+	lm93_read_block(client, 4, (u8 *)(data->block4));
+
+	/* fan1 - fan4: values & limits */
+	lm93_read_block(client, 5, (u8 *)(data->block5));
+	lm93_read_block(client, 8, (u8 *)(data->block8));
+
+	/* pmw control registers */
+	lm93_read_block(client, 9, (u8 *)(data->block9));
+
+	/* alarm values */
+	lm93_read_block(client, 1, (u8 *)(&data->block1));
+
+	/* auto/pwm registers */
+	lm93_read_block(client, 10, (u8 *)(&data->block10));
+
+	lm93_update_client_common(data, client);
+}
+
+/* update routine which uses SMBus byte/word data commands only */
+static void lm93_update_client_min(struct lm93_data *data,
+				   struct i2c_client *client)
+{
+	int i,j;
+	u8 *ptr;
+
+	dev_dbg(&client->dev,"starting device update (block data disabled)\n");
+
+	/* in1 - in16: values & limits */
+	for (i = 0; i < 16; i++) {
+		data->block3[i] =
+			lm93_read_byte(client, LM93_REG_IN(i));
+		data->block7[i].min =
+			lm93_read_byte(client, LM93_REG_IN_MIN(i));
+		data->block7[i].max =
+			lm93_read_byte(client, LM93_REG_IN_MAX(i));
+	}
+
+	/* temp1 - temp4: values */
+	for (i = 0; i < 4; i++) {
+		data->block2[i] =
+			lm93_read_byte(client, LM93_REG_TEMP(i));
+	}
+
+	/* prochot1 - prochot2: values */
+	for (i = 0; i < 2; i++) {
+		data->block4[i].cur =
+			lm93_read_byte(client, LM93_REG_PROCHOT_CUR(i));
+		data->block4[i].avg =
+			lm93_read_byte(client, LM93_REG_PROCHOT_AVG(i));
+	}
+
+	/* fan1 - fan4: values & limits */
+	for (i = 0; i < 4; i++) {
+		data->block5[i] =
+			lm93_read_word(client, LM93_REG_FAN(i));
+		data->block8[i] =
+			lm93_read_word(client, LM93_REG_FAN_MIN(i));
+	}
+
+	/* pwm control registers */
+	for (i = 0; i < 2; i++) {
+		for (j = 0; j < 4; j++) {
+			data->block9[i][j] =
+				lm93_read_byte(client, LM93_REG_PWM_CTL(i,j));
+		}
+	}
+
+	/* alarm values */
+	for (i = 0, ptr = (u8 *)(&data->block1); i < 8; i++) {
+		*(ptr + i) =
+			lm93_read_byte(client, LM93_REG_HOST_ERROR_1 + i);
+	}
+
+	/* auto/pwm (base temp) registers */
+	for (i = 0; i < 4; i++) {
+		data->block10.base[i] =
+			lm93_read_byte(client, LM93_REG_TEMP_BASE(i));
+	}
+
+	/* auto/pwm (offset temp) registers */
+	for (i = 0; i < 12; i++) {
+		data->block10.offset[i] =
+			lm93_read_byte(client, LM93_REG_TEMP_OFFSET(i));
+	}
+
+	lm93_update_client_common(data, client);
+}
+
+/* following are the sysfs callback functions */
+static ssize_t show_in(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf, "%d\n", LM93_IN_FROM_REG(nr, data->block3[nr]));
+}
+
+static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, show_in, NULL, 0);
+static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, show_in, NULL, 1);
+static SENSOR_DEVICE_ATTR(in3_input, S_IRUGO, show_in, NULL, 2);
+static SENSOR_DEVICE_ATTR(in4_input, S_IRUGO, show_in, NULL, 3);
+static SENSOR_DEVICE_ATTR(in5_input, S_IRUGO, show_in, NULL, 4);
+static SENSOR_DEVICE_ATTR(in6_input, S_IRUGO, show_in, NULL, 5);
+static SENSOR_DEVICE_ATTR(in7_input, S_IRUGO, show_in, NULL, 6);
+static SENSOR_DEVICE_ATTR(in8_input, S_IRUGO, show_in, NULL, 7);
+static SENSOR_DEVICE_ATTR(in9_input, S_IRUGO, show_in, NULL, 8);
+static SENSOR_DEVICE_ATTR(in10_input, S_IRUGO, show_in, NULL, 9);
+static SENSOR_DEVICE_ATTR(in11_input, S_IRUGO, show_in, NULL, 10);
+static SENSOR_DEVICE_ATTR(in12_input, S_IRUGO, show_in, NULL, 11);
+static SENSOR_DEVICE_ATTR(in13_input, S_IRUGO, show_in, NULL, 12);
+static SENSOR_DEVICE_ATTR(in14_input, S_IRUGO, show_in, NULL, 13);
+static SENSOR_DEVICE_ATTR(in15_input, S_IRUGO, show_in, NULL, 14);
+static SENSOR_DEVICE_ATTR(in16_input, S_IRUGO, show_in, NULL, 15);
+
+static ssize_t show_in_min(struct device *dev,
+			struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	int vccp = nr - 6;
+	long rc, vid;
+
+	if ((nr==6 || nr==7) && (vccp_limit_type[vccp])) {
+		vid = LM93_VID_FROM_REG(data->vid[vccp]);
+		rc = LM93_IN_MIN_FROM_REG(data->vccp_limits[vccp], vid);
+	}
+	else {
+		rc = LM93_IN_FROM_REG(nr, data->block7[nr].min); \
+	}
+	return sprintf(buf, "%ld\n", rc); \
+}
+
+static ssize_t store_in_min(struct device *dev, struct device_attribute *attr,
+			    const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+	int vccp = nr - 6;
+	long vid;
+
+	mutex_lock(&data->update_lock);
+	if ((nr==6 || nr==7) && (vccp_limit_type[vccp])) {
+		vid = LM93_VID_FROM_REG(data->vid[vccp]);
+		data->vccp_limits[vccp] = (data->vccp_limits[vccp] & 0xf0) |
+				LM93_IN_REL_TO_REG(val, 0, vid);
+		lm93_write_byte(client, LM93_REG_VCCP_LIMIT_OFF(vccp),
+				data->vccp_limits[vccp]);
+	}
+	else {
+		data->block7[nr].min = LM93_IN_TO_REG(nr,val);
+		lm93_write_byte(client, LM93_REG_IN_MIN(nr),
+				data->block7[nr].min);
+	}
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(in1_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 0);
+static SENSOR_DEVICE_ATTR(in2_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 1);
+static SENSOR_DEVICE_ATTR(in3_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 2);
+static SENSOR_DEVICE_ATTR(in4_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 3);
+static SENSOR_DEVICE_ATTR(in5_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 4);
+static SENSOR_DEVICE_ATTR(in6_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 5);
+static SENSOR_DEVICE_ATTR(in7_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 6);
+static SENSOR_DEVICE_ATTR(in8_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 7);
+static SENSOR_DEVICE_ATTR(in9_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 8);
+static SENSOR_DEVICE_ATTR(in10_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 9);
+static SENSOR_DEVICE_ATTR(in11_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 10);
+static SENSOR_DEVICE_ATTR(in12_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 11);
+static SENSOR_DEVICE_ATTR(in13_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 12);
+static SENSOR_DEVICE_ATTR(in14_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 13);
+static SENSOR_DEVICE_ATTR(in15_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 14);
+static SENSOR_DEVICE_ATTR(in16_min, S_IWUSR | S_IRUGO,
+			  show_in_min, store_in_min, 15);
+
+static ssize_t show_in_max(struct device *dev,
+			   struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	int vccp = nr - 6;
+	long rc, vid;
+
+	if ((nr==6 || nr==7) && (vccp_limit_type[vccp])) {
+		vid = LM93_VID_FROM_REG(data->vid[vccp]);
+		rc = LM93_IN_MAX_FROM_REG(data->vccp_limits[vccp],vid);
+	}
+	else {
+		rc = LM93_IN_FROM_REG(nr,data->block7[nr].max); \
+	}
+	return sprintf(buf,"%ld\n",rc); \
+}
+
+static ssize_t store_in_max(struct device *dev, struct device_attribute *attr,
+			    const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+	int vccp = nr - 6;
+	long vid;
+
+	mutex_lock(&data->update_lock);
+	if ((nr==6 || nr==7) && (vccp_limit_type[vccp])) {
+		vid = LM93_VID_FROM_REG(data->vid[vccp]);
+		data->vccp_limits[vccp] = (data->vccp_limits[vccp] & 0x0f) |
+				LM93_IN_REL_TO_REG(val, 1, vid);
+		lm93_write_byte(client, LM93_REG_VCCP_LIMIT_OFF(vccp),
+				data->vccp_limits[vccp]);
+	}
+	else {
+		data->block7[nr].max = LM93_IN_TO_REG(nr,val);
+		lm93_write_byte(client, LM93_REG_IN_MAX(nr),
+				data->block7[nr].max);
+	}
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(in1_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 0);
+static SENSOR_DEVICE_ATTR(in2_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 1);
+static SENSOR_DEVICE_ATTR(in3_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 2);
+static SENSOR_DEVICE_ATTR(in4_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 3);
+static SENSOR_DEVICE_ATTR(in5_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 4);
+static SENSOR_DEVICE_ATTR(in6_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 5);
+static SENSOR_DEVICE_ATTR(in7_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 6);
+static SENSOR_DEVICE_ATTR(in8_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 7);
+static SENSOR_DEVICE_ATTR(in9_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 8);
+static SENSOR_DEVICE_ATTR(in10_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 9);
+static SENSOR_DEVICE_ATTR(in11_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 10);
+static SENSOR_DEVICE_ATTR(in12_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 11);
+static SENSOR_DEVICE_ATTR(in13_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 12);
+static SENSOR_DEVICE_ATTR(in14_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 13);
+static SENSOR_DEVICE_ATTR(in15_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 14);
+static SENSOR_DEVICE_ATTR(in16_max, S_IWUSR | S_IRUGO,
+			  show_in_max, store_in_max, 15);
+
+static ssize_t show_temp(struct device *dev,
+			 struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",LM93_TEMP_FROM_REG(data->block2[nr]));
+}
+
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_temp, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp3_input, S_IRUGO, show_temp, NULL, 2);
+
+static ssize_t show_temp_min(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",LM93_TEMP_FROM_REG(data->temp_lim[nr].min));
+}
+
+static ssize_t store_temp_min(struct device *dev, struct device_attribute *attr,
+			      const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	data->temp_lim[nr].min = LM93_TEMP_TO_REG(val);
+	lm93_write_byte(client, LM93_REG_TEMP_MIN(nr), data->temp_lim[nr].min);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO,
+			  show_temp_min, store_temp_min, 0);
+static SENSOR_DEVICE_ATTR(temp2_min, S_IWUSR | S_IRUGO,
+			  show_temp_min, store_temp_min, 1);
+static SENSOR_DEVICE_ATTR(temp3_min, S_IWUSR | S_IRUGO,
+			  show_temp_min, store_temp_min, 2);
+
+static ssize_t show_temp_max(struct device *dev,
+			     struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",LM93_TEMP_FROM_REG(data->temp_lim[nr].max));
+}
+
+static ssize_t store_temp_max(struct device *dev, struct device_attribute *attr,
+			      const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	data->temp_lim[nr].max = LM93_TEMP_TO_REG(val);
+	lm93_write_byte(client, LM93_REG_TEMP_MAX(nr), data->temp_lim[nr].max);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO,
+			  show_temp_max, store_temp_max, 0);
+static SENSOR_DEVICE_ATTR(temp2_max, S_IWUSR | S_IRUGO,
+			  show_temp_max, store_temp_max, 1);
+static SENSOR_DEVICE_ATTR(temp3_max, S_IWUSR | S_IRUGO,
+			  show_temp_max, store_temp_max, 2);
+
+static ssize_t show_temp_auto_base(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",LM93_TEMP_FROM_REG(data->block10.base[nr]));
+}
+
+static ssize_t store_temp_auto_base(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	data->block10.base[nr] = LM93_TEMP_TO_REG(val);
+	lm93_write_byte(client, LM93_REG_TEMP_BASE(nr), data->block10.base[nr]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(temp1_auto_base, S_IWUSR | S_IRUGO,
+			  show_temp_auto_base, store_temp_auto_base, 0);
+static SENSOR_DEVICE_ATTR(temp2_auto_base, S_IWUSR | S_IRUGO,
+			  show_temp_auto_base, store_temp_auto_base, 1);
+static SENSOR_DEVICE_ATTR(temp3_auto_base, S_IWUSR | S_IRUGO,
+			  show_temp_auto_base, store_temp_auto_base, 2);
+
+static ssize_t show_temp_auto_boost(struct device *dev,
+				    struct device_attribute *attr,char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",LM93_TEMP_FROM_REG(data->boost[nr]));
+}
+
+static ssize_t store_temp_auto_boost(struct device *dev,
+				     struct device_attribute *attr,
+				     const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	data->boost[nr] = LM93_TEMP_TO_REG(val);
+	lm93_write_byte(client, LM93_REG_BOOST(nr), data->boost[nr]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(temp1_auto_boost, S_IWUSR | S_IRUGO,
+			  show_temp_auto_boost, store_temp_auto_boost, 0);
+static SENSOR_DEVICE_ATTR(temp2_auto_boost, S_IWUSR | S_IRUGO,
+			  show_temp_auto_boost, store_temp_auto_boost, 1);
+static SENSOR_DEVICE_ATTR(temp3_auto_boost, S_IWUSR | S_IRUGO,
+			  show_temp_auto_boost, store_temp_auto_boost, 2);
+
+static ssize_t show_temp_auto_boost_hyst(struct device *dev,
+					 struct device_attribute *attr,
+					 char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	int mode = LM93_TEMP_OFFSET_MODE_FROM_REG(data->sfc2, nr);
+	return sprintf(buf,"%d\n",
+		       LM93_AUTO_BOOST_HYST_FROM_REGS(data, nr, mode));
+}
+
+static ssize_t store_temp_auto_boost_hyst(struct device *dev,
+					  struct device_attribute *attr,
+					  const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	/* force 0.5C/bit mode */
+	data->sfc2 = lm93_read_byte(client, LM93_REG_SFC2);
+	data->sfc2 |= ((nr < 2) ? 0x10 : 0x20);
+	lm93_write_byte(client, LM93_REG_SFC2, data->sfc2);
+	data->boost_hyst[nr/2] = LM93_AUTO_BOOST_HYST_TO_REG(data, val, nr, 1);
+	lm93_write_byte(client, LM93_REG_BOOST_HYST(nr),
+			data->boost_hyst[nr/2]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(temp1_auto_boost_hyst, S_IWUSR | S_IRUGO,
+			  show_temp_auto_boost_hyst,
+			  store_temp_auto_boost_hyst, 0);
+static SENSOR_DEVICE_ATTR(temp2_auto_boost_hyst, S_IWUSR | S_IRUGO,
+			  show_temp_auto_boost_hyst,
+			  store_temp_auto_boost_hyst, 1);
+static SENSOR_DEVICE_ATTR(temp3_auto_boost_hyst, S_IWUSR | S_IRUGO,
+			  show_temp_auto_boost_hyst,
+			  store_temp_auto_boost_hyst, 2);
+
+static ssize_t show_temp_auto_offset(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct sensor_device_attribute_2 *s_attr = to_sensor_dev_attr_2(attr);
+	int nr = s_attr->index;
+	int ofs = s_attr->nr;
+	struct lm93_data *data = lm93_update_device(dev);
+	int mode = LM93_TEMP_OFFSET_MODE_FROM_REG(data->sfc2, nr);
+	return sprintf(buf,"%d\n",
+	       LM93_TEMP_AUTO_OFFSET_FROM_REG(data->block10.offset[ofs],
+					      nr,mode));
+}
+
+static ssize_t store_temp_auto_offset(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *s_attr = to_sensor_dev_attr_2(attr);
+	int nr = s_attr->index;
+	int ofs = s_attr->nr;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	/* force 0.5C/bit mode */
+	data->sfc2 = lm93_read_byte(client, LM93_REG_SFC2);
+	data->sfc2 |= ((nr < 2) ? 0x10 : 0x20);
+	lm93_write_byte(client, LM93_REG_SFC2, data->sfc2);
+	data->block10.offset[ofs] = LM93_TEMP_AUTO_OFFSET_TO_REG(
+			data->block10.offset[ofs], val, nr, 1);
+	lm93_write_byte(client, LM93_REG_TEMP_OFFSET(ofs),
+			data->block10.offset[ofs]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR_2(temp1_auto_offset1, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 0, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_offset2, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 1, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_offset3, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 2, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_offset4, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 3, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_offset5, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 4, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_offset6, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 5, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_offset7, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 6, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_offset8, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 7, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_offset9, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 8, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_offset10, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 9, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_offset11, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 10, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_offset12, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 11, 0);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_offset1, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 0, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_offset2, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 1, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_offset3, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 2, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_offset4, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 3, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_offset5, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 4, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_offset6, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 5, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_offset7, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 6, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_offset8, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 7, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_offset9, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 8, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_offset10, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 9, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_offset11, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 10, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_offset12, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 11, 1);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_offset1, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 0, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_offset2, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 1, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_offset3, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 2, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_offset4, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 3, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_offset5, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 4, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_offset6, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 5, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_offset7, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 6, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_offset8, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 7, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_offset9, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 8, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_offset10, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 9, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_offset11, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 10, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_offset12, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset, store_temp_auto_offset, 11, 2);
+
+static ssize_t show_temp_auto_pwm_min(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	u8 reg, ctl4;
+	struct lm93_data *data = lm93_update_device(dev);
+	reg = data->auto_pwm_min_hyst[nr/2] >> 4 & 0x0f;
+	ctl4 = data->block9[nr][LM93_PWM_CTL4];
+	return sprintf(buf,"%d\n",LM93_PWM_FROM_REG(reg, (ctl4 & 0x07) ?
+				LM93_PWM_MAP_LO_FREQ : LM93_PWM_MAP_HI_FREQ));
+}
+
+static ssize_t store_temp_auto_pwm_min(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+	u8 reg, ctl4;
+
+	mutex_lock(&data->update_lock);
+	reg = lm93_read_byte(client, LM93_REG_PWM_MIN_HYST(nr));
+	ctl4 = lm93_read_byte(client, LM93_REG_PWM_CTL(nr,LM93_PWM_CTL4));
+	reg = (reg & 0x0f) |
+		LM93_PWM_TO_REG(val, (ctl4 & 0x07) ?
+				LM93_PWM_MAP_LO_FREQ :
+				LM93_PWM_MAP_HI_FREQ) << 4;
+	data->auto_pwm_min_hyst[nr/2] = reg;
+	lm93_write_byte(client, LM93_REG_PWM_MIN_HYST(nr), reg);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(temp1_auto_pwm_min, S_IWUSR | S_IRUGO,
+			  show_temp_auto_pwm_min,
+			  store_temp_auto_pwm_min, 0);
+static SENSOR_DEVICE_ATTR(temp2_auto_pwm_min, S_IWUSR | S_IRUGO,
+			  show_temp_auto_pwm_min,
+			  store_temp_auto_pwm_min, 1);
+static SENSOR_DEVICE_ATTR(temp3_auto_pwm_min, S_IWUSR | S_IRUGO,
+			  show_temp_auto_pwm_min,
+			  store_temp_auto_pwm_min, 2);
+
+static ssize_t show_temp_auto_offset_hyst(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	int mode = LM93_TEMP_OFFSET_MODE_FROM_REG(data->sfc2, nr);
+	return sprintf(buf,"%d\n",LM93_TEMP_OFFSET_FROM_REG(
+					data->auto_pwm_min_hyst[nr/2], mode));
+}
+
+static ssize_t store_temp_auto_offset_hyst(struct device *dev,
+						struct device_attribute *attr,
+						const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+	u8 reg;
+
+	mutex_lock(&data->update_lock);
+	/* force 0.5C/bit mode */
+	data->sfc2 = lm93_read_byte(client, LM93_REG_SFC2);
+	data->sfc2 |= ((nr < 2) ? 0x10 : 0x20);
+	lm93_write_byte(client, LM93_REG_SFC2, data->sfc2);
+	reg = data->auto_pwm_min_hyst[nr/2];
+	reg = (reg & 0xf0) | (LM93_TEMP_OFFSET_TO_REG(val, 1) & 0x0f);
+	data->auto_pwm_min_hyst[nr/2] = reg;
+	lm93_write_byte(client, LM93_REG_PWM_MIN_HYST(nr), reg);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(temp1_auto_offset_hyst, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset_hyst,
+			  store_temp_auto_offset_hyst, 0);
+static SENSOR_DEVICE_ATTR(temp2_auto_offset_hyst, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset_hyst,
+			  store_temp_auto_offset_hyst, 1);
+static SENSOR_DEVICE_ATTR(temp3_auto_offset_hyst, S_IWUSR | S_IRUGO,
+			  show_temp_auto_offset_hyst,
+			  store_temp_auto_offset_hyst, 2);
+
+static ssize_t show_fan_input(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct sensor_device_attribute *s_attr = to_sensor_dev_attr(attr);
+	int nr = s_attr->index;
+	struct lm93_data *data = lm93_update_device(dev);
+
+	return sprintf(buf,"%d\n",LM93_FAN_FROM_REG(data->block5[nr]));
+}
+
+static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_fan_input, NULL, 0);
+static SENSOR_DEVICE_ATTR(fan2_input, S_IRUGO, show_fan_input, NULL, 1);
+static SENSOR_DEVICE_ATTR(fan3_input, S_IRUGO, show_fan_input, NULL, 2);
+static SENSOR_DEVICE_ATTR(fan4_input, S_IRUGO, show_fan_input, NULL, 3);
+
+static ssize_t show_fan_min(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+
+	return sprintf(buf,"%d\n",LM93_FAN_FROM_REG(data->block8[nr]));
+}
+
+static ssize_t store_fan_min(struct device *dev, struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	data->block8[nr] = LM93_FAN_TO_REG(val);
+	lm93_write_word(client,LM93_REG_FAN_MIN(nr),data->block8[nr]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(fan1_min, S_IWUSR | S_IRUGO,
+			  show_fan_min, store_fan_min, 0);
+static SENSOR_DEVICE_ATTR(fan2_min, S_IWUSR | S_IRUGO,
+			  show_fan_min, store_fan_min, 1);
+static SENSOR_DEVICE_ATTR(fan3_min, S_IWUSR | S_IRUGO,
+			  show_fan_min, store_fan_min, 2);
+static SENSOR_DEVICE_ATTR(fan4_min, S_IWUSR | S_IRUGO,
+			  show_fan_min, store_fan_min, 3);
+
+/* some tedious bit-twiddling here to deal with the register format:
+
+	data->sf_tach_to_pwm: (tach to pwm mapping bits)
+
+		bit |  7  |  6  |  5  |  4  |  3  |  2  |  1  |  0
+		     T4:P2 T4:P1 T3:P2 T3:P1 T2:P2 T2:P1 T1:P2 T1:P1
+
+	data->sfc2: (enable bits)
+
+		bit |  3  |  2  |  1  |  0
+		       T4    T3    T2    T1
+*/
+
+static ssize_t show_fan_smart_tach(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	long rc = 0;
+	int mapping;
+
+	/* extract the relevant mapping */
+	mapping = (data->sf_tach_to_pwm >> (nr * 2)) & 0x03;
+
+	/* if there's a mapping and it's enabled */
+	if (mapping && ((data->sfc2 >> nr) & 0x01))
+		rc = mapping;
+	return sprintf(buf,"%ld\n",rc);
+}
+
+/* helper function - must grab data->update_lock before calling
+   fan is 0-3, indicating fan1-fan4 */
+static void lm93_write_fan_smart_tach(struct i2c_client *client,
+	struct lm93_data *data, int fan, long value)
+{
+	/* insert the new mapping and write it out */
+	data->sf_tach_to_pwm = lm93_read_byte(client, LM93_REG_SF_TACH_TO_PWM);
+	data->sf_tach_to_pwm &= ~(0x3 << fan * 2);
+	data->sf_tach_to_pwm |= value << fan * 2;
+	lm93_write_byte(client, LM93_REG_SF_TACH_TO_PWM, data->sf_tach_to_pwm);
+
+	/* insert the enable bit and write it out */
+	data->sfc2 = lm93_read_byte(client, LM93_REG_SFC2);
+	if (value)
+		data->sfc2 |= 1 << fan;
+	else
+		data->sfc2 &= ~(1 << fan);
+	lm93_write_byte(client, LM93_REG_SFC2, data->sfc2);
+}
+
+static ssize_t store_fan_smart_tach(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	/* sanity test, ignore the write otherwise */
+	if (0 <= val && val <= 2) {
+		/* can't enable if pwm freq is 22.5KHz */
+		if (val) {
+			u8 ctl4 = lm93_read_byte(client,
+				LM93_REG_PWM_CTL(val-1,LM93_PWM_CTL4));
+			if ((ctl4 & 0x07) == 0)
+				val = 0;
+		}
+		lm93_write_fan_smart_tach(client, data, nr, val);
+	}
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(fan1_smart_tach, S_IWUSR | S_IRUGO,
+			  show_fan_smart_tach, store_fan_smart_tach, 0);
+static SENSOR_DEVICE_ATTR(fan2_smart_tach, S_IWUSR | S_IRUGO,
+			  show_fan_smart_tach, store_fan_smart_tach, 1);
+static SENSOR_DEVICE_ATTR(fan3_smart_tach, S_IWUSR | S_IRUGO,
+			  show_fan_smart_tach, store_fan_smart_tach, 2);
+static SENSOR_DEVICE_ATTR(fan4_smart_tach, S_IWUSR | S_IRUGO,
+			  show_fan_smart_tach, store_fan_smart_tach, 3);
+
+static ssize_t show_pwm(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	u8 ctl2, ctl4;
+	long rc;
+
+	ctl2 = data->block9[nr][LM93_PWM_CTL2];
+	ctl4 = data->block9[nr][LM93_PWM_CTL4];
+	if (ctl2 & 0x01) /* show user commanded value if enabled */
+		rc = data->pwm_override[nr];
+	else /* show present h/w value if manual pwm disabled */
+		rc = LM93_PWM_FROM_REG(ctl2 >> 4, (ctl4 & 0x07) ?
+			LM93_PWM_MAP_LO_FREQ : LM93_PWM_MAP_HI_FREQ);
+	return sprintf(buf,"%ld\n",rc);
+}
+
+static ssize_t store_pwm(struct device *dev, struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+	u8 ctl2, ctl4;
+
+	mutex_lock(&data->update_lock);
+	ctl2 = lm93_read_byte(client,LM93_REG_PWM_CTL(nr,LM93_PWM_CTL2));
+	ctl4 = lm93_read_byte(client, LM93_REG_PWM_CTL(nr,LM93_PWM_CTL4));
+	ctl2 = (ctl2 & 0x0f) | LM93_PWM_TO_REG(val,(ctl4 & 0x07) ?
+			LM93_PWM_MAP_LO_FREQ : LM93_PWM_MAP_HI_FREQ) << 4;
+	/* save user commanded value */
+	data->pwm_override[nr] = LM93_PWM_FROM_REG(ctl2 >> 4,
+			(ctl4 & 0x07) ?  LM93_PWM_MAP_LO_FREQ :
+			LM93_PWM_MAP_HI_FREQ);
+	lm93_write_byte(client,LM93_REG_PWM_CTL(nr,LM93_PWM_CTL2),ctl2);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 0);
+static SENSOR_DEVICE_ATTR(pwm2, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 1);
+
+static ssize_t show_pwm_enable(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	u8 ctl2;
+	long rc;
+
+	ctl2 = data->block9[nr][LM93_PWM_CTL2];
+	if (ctl2 & 0x01) /* manual override enabled ? */
+		rc = ((ctl2 & 0xF0) == 0xF0) ? 0 : 1;
+	else
+		rc = 2;
+	return sprintf(buf,"%ld\n",rc);
+}
+
+static ssize_t store_pwm_enable(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+	u8 ctl2;
+
+	mutex_lock(&data->update_lock);
+	ctl2 = lm93_read_byte(client,LM93_REG_PWM_CTL(nr,LM93_PWM_CTL2));
+
+	switch (val) {
+	case 0:
+		ctl2 |= 0xF1; /* enable manual override, set PWM to max */
+		break;
+	case 1: ctl2 |= 0x01; /* enable manual override */
+		break;
+	case 2: ctl2 &= ~0x01; /* disable manual override */
+		break;
+	default:
+		mutex_unlock(&data->update_lock);
+		return -EINVAL;
+	}
+
+	lm93_write_byte(client,LM93_REG_PWM_CTL(nr,LM93_PWM_CTL2),ctl2);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(pwm1_enable, S_IWUSR | S_IRUGO,
+				show_pwm_enable, store_pwm_enable, 0);
+static SENSOR_DEVICE_ATTR(pwm2_enable, S_IWUSR | S_IRUGO,
+				show_pwm_enable, store_pwm_enable, 1);
+
+static ssize_t show_pwm_freq(struct device *dev, struct device_attribute *attr,
+				char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	u8 ctl4;
+
+	ctl4 = data->block9[nr][LM93_PWM_CTL4];
+	return sprintf(buf,"%d\n",LM93_PWM_FREQ_FROM_REG(ctl4));
+}
+
+/* helper function - must grab data->update_lock before calling
+   pwm is 0-1, indicating pwm1-pwm2
+   this disables smart tach for all tach channels bound to the given pwm */
+static void lm93_disable_fan_smart_tach(struct i2c_client *client,
+	struct lm93_data *data, int pwm)
+{
+	int mapping = lm93_read_byte(client, LM93_REG_SF_TACH_TO_PWM);
+	int mask;
+
+	/* collapse the mapping into a mask of enable bits */
+	mapping = (mapping >> pwm) & 0x55;
+	mask = mapping & 0x01;
+	mask |= (mapping & 0x04) >> 1;
+	mask |= (mapping & 0x10) >> 2;
+	mask |= (mapping & 0x40) >> 3;
+
+	/* disable smart tach according to the mask */
+	data->sfc2 = lm93_read_byte(client, LM93_REG_SFC2);
+	data->sfc2 &= ~mask;
+	lm93_write_byte(client, LM93_REG_SFC2, data->sfc2);
+}
+
+static ssize_t store_pwm_freq(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+	u8 ctl4;
+
+	mutex_lock(&data->update_lock);
+	ctl4 = lm93_read_byte(client,LM93_REG_PWM_CTL(nr,LM93_PWM_CTL4));
+	ctl4 = (ctl4 & 0xf8) | LM93_PWM_FREQ_TO_REG(val);
+	data->block9[nr][LM93_PWM_CTL4] = ctl4;
+	/* ctl4 == 0 -> 22.5KHz -> disable smart tach */
+	if (!ctl4)
+		lm93_disable_fan_smart_tach(client, data, nr);
+	lm93_write_byte(client,	LM93_REG_PWM_CTL(nr,LM93_PWM_CTL4), ctl4);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(pwm1_freq, S_IWUSR | S_IRUGO,
+			  show_pwm_freq, store_pwm_freq, 0);
+static SENSOR_DEVICE_ATTR(pwm2_freq, S_IWUSR | S_IRUGO,
+			  show_pwm_freq, store_pwm_freq, 1);
+
+static ssize_t show_pwm_auto_channels(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",data->block9[nr][LM93_PWM_CTL1]);
+}
+
+static ssize_t store_pwm_auto_channels(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	data->block9[nr][LM93_PWM_CTL1] = SENSORS_LIMIT(val, 0, 255);
+	lm93_write_byte(client,	LM93_REG_PWM_CTL(nr,LM93_PWM_CTL1),
+				data->block9[nr][LM93_PWM_CTL1]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(pwm1_auto_channels, S_IWUSR | S_IRUGO,
+			  show_pwm_auto_channels, store_pwm_auto_channels, 0);
+static SENSOR_DEVICE_ATTR(pwm2_auto_channels, S_IWUSR | S_IRUGO,
+			  show_pwm_auto_channels, store_pwm_auto_channels, 1);
+
+static ssize_t show_pwm_auto_spinup_min(struct device *dev,
+				struct device_attribute *attr,char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	u8 ctl3, ctl4;
+
+	ctl3 = data->block9[nr][LM93_PWM_CTL3];
+	ctl4 = data->block9[nr][LM93_PWM_CTL4];
+	return sprintf(buf,"%d\n",
+		       LM93_PWM_FROM_REG(ctl3 & 0x0f, (ctl4 & 0x07) ?
+			LM93_PWM_MAP_LO_FREQ : LM93_PWM_MAP_HI_FREQ));
+}
+
+static ssize_t store_pwm_auto_spinup_min(struct device *dev,
+						struct device_attribute *attr,
+						const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+	u8 ctl3, ctl4;
+
+	mutex_lock(&data->update_lock);
+	ctl3 = lm93_read_byte(client,LM93_REG_PWM_CTL(nr, LM93_PWM_CTL3));
+	ctl4 = lm93_read_byte(client,LM93_REG_PWM_CTL(nr, LM93_PWM_CTL4));
+	ctl3 = (ctl3 & 0xf0) | 	LM93_PWM_TO_REG(val, (ctl4 & 0x07) ?
+			LM93_PWM_MAP_LO_FREQ :
+			LM93_PWM_MAP_HI_FREQ);
+	data->block9[nr][LM93_PWM_CTL3] = ctl3;
+	lm93_write_byte(client,LM93_REG_PWM_CTL(nr, LM93_PWM_CTL3), ctl3);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(pwm1_auto_spinup_min, S_IWUSR | S_IRUGO,
+			  show_pwm_auto_spinup_min,
+			  store_pwm_auto_spinup_min, 0);
+static SENSOR_DEVICE_ATTR(pwm2_auto_spinup_min, S_IWUSR | S_IRUGO,
+			  show_pwm_auto_spinup_min,
+			  store_pwm_auto_spinup_min, 1);
+
+static ssize_t show_pwm_auto_spinup_time(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",LM93_SPINUP_TIME_FROM_REG(
+				data->block9[nr][LM93_PWM_CTL3]));
+}
+
+static ssize_t store_pwm_auto_spinup_time(struct device *dev,
+						struct device_attribute *attr,
+						const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+	u8 ctl3;
+
+	mutex_lock(&data->update_lock);
+	ctl3 = lm93_read_byte(client,LM93_REG_PWM_CTL(nr, LM93_PWM_CTL3));
+	ctl3 = (ctl3 & 0x1f) | (LM93_SPINUP_TIME_TO_REG(val) << 5 & 0xe0);
+	data->block9[nr][LM93_PWM_CTL3] = ctl3;
+	lm93_write_byte(client,LM93_REG_PWM_CTL(nr, LM93_PWM_CTL3), ctl3);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(pwm1_auto_spinup_time, S_IWUSR | S_IRUGO,
+			  show_pwm_auto_spinup_time,
+			  store_pwm_auto_spinup_time, 0);
+static SENSOR_DEVICE_ATTR(pwm2_auto_spinup_time, S_IWUSR | S_IRUGO,
+			  show_pwm_auto_spinup_time,
+			  store_pwm_auto_spinup_time, 1);
+
+static ssize_t show_pwm_auto_prochot_ramp(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",
+		       LM93_RAMP_FROM_REG(data->pwm_ramp_ctl >> 4 & 0x0f));
+}
+
+static ssize_t store_pwm_auto_prochot_ramp(struct device *dev,
+						struct device_attribute *attr,
+						const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+	u8 ramp;
+
+	mutex_lock(&data->update_lock);
+	ramp = lm93_read_byte(client, LM93_REG_PWM_RAMP_CTL);
+	ramp = (ramp & 0x0f) | (LM93_RAMP_TO_REG(val) << 4 & 0xf0);
+	lm93_write_byte(client, LM93_REG_PWM_RAMP_CTL, ramp);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static DEVICE_ATTR(pwm_auto_prochot_ramp, S_IRUGO | S_IWUSR,
+			show_pwm_auto_prochot_ramp,
+			store_pwm_auto_prochot_ramp);
+
+static ssize_t show_pwm_auto_vrdhot_ramp(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",
+		       LM93_RAMP_FROM_REG(data->pwm_ramp_ctl & 0x0f));
+}
+
+static ssize_t store_pwm_auto_vrdhot_ramp(struct device *dev,
+						struct device_attribute *attr,
+						const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+	u8 ramp;
+
+	mutex_lock(&data->update_lock);
+	ramp = lm93_read_byte(client, LM93_REG_PWM_RAMP_CTL);
+	ramp = (ramp & 0xf0) | (LM93_RAMP_TO_REG(val) & 0x0f);
+	lm93_write_byte(client, LM93_REG_PWM_RAMP_CTL, ramp);
+	mutex_unlock(&data->update_lock);
+	return 0;
+}
+
+static DEVICE_ATTR(pwm_auto_vrdhot_ramp, S_IRUGO | S_IWUSR,
+			show_pwm_auto_vrdhot_ramp,
+			store_pwm_auto_vrdhot_ramp);
+
+static ssize_t show_vid(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",LM93_VID_FROM_REG(data->vid[nr]));
+}
+
+static SENSOR_DEVICE_ATTR(vid1, S_IRUGO, show_vid, NULL, 0);
+static SENSOR_DEVICE_ATTR(vid2, S_IRUGO, show_vid, NULL, 1);
+
+static ssize_t show_prochot(struct device *dev, struct device_attribute *attr,
+				char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",data->block4[nr].cur);
+}
+
+static SENSOR_DEVICE_ATTR(prochot1, S_IRUGO, show_prochot, NULL, 0);
+static SENSOR_DEVICE_ATTR(prochot2, S_IRUGO, show_prochot, NULL, 1);
+
+static ssize_t show_prochot_avg(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",data->block4[nr].avg);
+}
+
+static SENSOR_DEVICE_ATTR(prochot1_avg, S_IRUGO, show_prochot_avg, NULL, 0);
+static SENSOR_DEVICE_ATTR(prochot2_avg, S_IRUGO, show_prochot_avg, NULL, 1);
+
+static ssize_t show_prochot_max(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",data->prochot_max[nr]);
+}
+
+static ssize_t store_prochot_max(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	data->prochot_max[nr] = LM93_PROCHOT_TO_REG(val);
+	lm93_write_byte(client, LM93_REG_PROCHOT_MAX(nr),
+			data->prochot_max[nr]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(prochot1_max, S_IWUSR | S_IRUGO,
+			  show_prochot_max, store_prochot_max, 0);
+static SENSOR_DEVICE_ATTR(prochot2_max, S_IWUSR | S_IRUGO,
+			  show_prochot_max, store_prochot_max, 1);
+
+static const u8 prochot_override_mask[] = { 0x80, 0x40 };
+
+static ssize_t show_prochot_override(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",
+		(data->prochot_override & prochot_override_mask[nr]) ? 1 : 0);
+}
+
+static ssize_t store_prochot_override(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	if (val)
+		data->prochot_override |= prochot_override_mask[nr];
+	else
+		data->prochot_override &= (~prochot_override_mask[nr]);
+	lm93_write_byte(client, LM93_REG_PROCHOT_OVERRIDE,
+			data->prochot_override);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(prochot1_override, S_IWUSR | S_IRUGO,
+			  show_prochot_override, store_prochot_override, 0);
+static SENSOR_DEVICE_ATTR(prochot2_override, S_IWUSR | S_IRUGO,
+			  show_prochot_override, store_prochot_override, 1);
+
+static ssize_t show_prochot_interval(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	u8 tmp;
+	if (nr==1)
+		tmp = (data->prochot_interval & 0xf0) >> 4;
+	else
+		tmp = data->prochot_interval & 0x0f;
+	return sprintf(buf,"%d\n",LM93_INTERVAL_FROM_REG(tmp));
+}
+
+static ssize_t store_prochot_interval(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+	u8 tmp;
+
+	mutex_lock(&data->update_lock);
+	tmp = lm93_read_byte(client, LM93_REG_PROCHOT_INTERVAL);
+	if (nr==1)
+		tmp = (tmp & 0x0f) | (LM93_INTERVAL_TO_REG(val) << 4);
+	else
+		tmp = (tmp & 0xf0) | LM93_INTERVAL_TO_REG(val);
+	data->prochot_interval = tmp;
+	lm93_write_byte(client, LM93_REG_PROCHOT_INTERVAL, tmp);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR(prochot1_interval, S_IWUSR | S_IRUGO,
+			  show_prochot_interval, store_prochot_interval, 0);
+static SENSOR_DEVICE_ATTR(prochot2_interval, S_IWUSR | S_IRUGO,
+			  show_prochot_interval, store_prochot_interval, 1);
+
+static ssize_t show_prochot_override_duty_cycle(struct device *dev,
+						struct device_attribute *attr,
+						char *buf)
+{
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",data->prochot_override & 0x0f);
+}
+
+static ssize_t store_prochot_override_duty_cycle(struct device *dev,
+						struct device_attribute *attr,
+						const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	data->prochot_override = (data->prochot_override & 0xf0) |
+					SENSORS_LIMIT(val, 0, 15);
+	lm93_write_byte(client, LM93_REG_PROCHOT_OVERRIDE,
+			data->prochot_override);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static DEVICE_ATTR(prochot_override_duty_cycle, S_IRUGO | S_IWUSR,
+			show_prochot_override_duty_cycle,
+			store_prochot_override_duty_cycle);
+
+static ssize_t show_prochot_short(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",(data->config & 0x10) ? 1 : 0);
+}
+
+static ssize_t store_prochot_short(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm93_data *data = i2c_get_clientdata(client);
+	u32 val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	if (val)
+		data->config |= 0x10;
+	else
+		data->config &= ~0x10;
+	lm93_write_byte(client, LM93_REG_CONFIG, data->config);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static DEVICE_ATTR(prochot_short, S_IRUGO | S_IWUSR,
+		   show_prochot_short, store_prochot_short);
+
+static ssize_t show_vrdhot(struct device *dev, struct device_attribute *attr,
+				char *buf)
+{
+	int nr = (to_sensor_dev_attr(attr))->index;
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",
+		       data->block1.host_status_1 & (1 << (nr+4)) ? 1 : 0);
+}
+
+static SENSOR_DEVICE_ATTR(vrdhot1, S_IRUGO, show_vrdhot, NULL, 0);
+static SENSOR_DEVICE_ATTR(vrdhot2, S_IRUGO, show_vrdhot, NULL, 1);
+
+static ssize_t show_gpio(struct device *dev, struct device_attribute *attr,
+				char *buf)
+{
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",LM93_GPI_FROM_REG(data->gpi));
+}
+
+static DEVICE_ATTR(gpio, S_IRUGO, show_gpio, NULL);
+
+static ssize_t show_alarms(struct device *dev, struct device_attribute *attr,
+				char *buf)
+{
+	struct lm93_data *data = lm93_update_device(dev);
+	return sprintf(buf,"%d\n",LM93_ALARMS_FROM_REG(data->block1));
+}
+
+static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
+
+static struct attribute *lm93_attrs[] = {
+	&sensor_dev_attr_in1_input.dev_attr.attr,
+	&sensor_dev_attr_in2_input.dev_attr.attr,
+	&sensor_dev_attr_in3_input.dev_attr.attr,
+	&sensor_dev_attr_in4_input.dev_attr.attr,
+	&sensor_dev_attr_in5_input.dev_attr.attr,
+	&sensor_dev_attr_in6_input.dev_attr.attr,
+	&sensor_dev_attr_in7_input.dev_attr.attr,
+	&sensor_dev_attr_in8_input.dev_attr.attr,
+	&sensor_dev_attr_in9_input.dev_attr.attr,
+	&sensor_dev_attr_in10_input.dev_attr.attr,
+	&sensor_dev_attr_in11_input.dev_attr.attr,
+	&sensor_dev_attr_in12_input.dev_attr.attr,
+	&sensor_dev_attr_in13_input.dev_attr.attr,
+	&sensor_dev_attr_in14_input.dev_attr.attr,
+	&sensor_dev_attr_in15_input.dev_attr.attr,
+	&sensor_dev_attr_in16_input.dev_attr.attr,
+	&sensor_dev_attr_in1_min.dev_attr.attr,
+	&sensor_dev_attr_in2_min.dev_attr.attr,
+	&sensor_dev_attr_in3_min.dev_attr.attr,
+	&sensor_dev_attr_in4_min.dev_attr.attr,
+	&sensor_dev_attr_in5_min.dev_attr.attr,
+	&sensor_dev_attr_in6_min.dev_attr.attr,
+	&sensor_dev_attr_in7_min.dev_attr.attr,
+	&sensor_dev_attr_in8_min.dev_attr.attr,
+	&sensor_dev_attr_in9_min.dev_attr.attr,
+	&sensor_dev_attr_in10_min.dev_attr.attr,
+	&sensor_dev_attr_in11_min.dev_attr.attr,
+	&sensor_dev_attr_in12_min.dev_attr.attr,
+	&sensor_dev_attr_in13_min.dev_attr.attr,
+	&sensor_dev_attr_in14_min.dev_attr.attr,
+	&sensor_dev_attr_in15_min.dev_attr.attr,
+	&sensor_dev_attr_in16_min.dev_attr.attr,
+	&sensor_dev_attr_in1_max.dev_attr.attr,
+	&sensor_dev_attr_in2_max.dev_attr.attr,
+	&sensor_dev_attr_in3_max.dev_attr.attr,
+	&sensor_dev_attr_in4_max.dev_attr.attr,
+	&sensor_dev_attr_in5_max.dev_attr.attr,
+	&sensor_dev_attr_in6_max.dev_attr.attr,
+	&sensor_dev_attr_in7_max.dev_attr.attr,
+	&sensor_dev_attr_in8_max.dev_attr.attr,
+	&sensor_dev_attr_in9_max.dev_attr.attr,
+	&sensor_dev_attr_in10_max.dev_attr.attr,
+	&sensor_dev_attr_in11_max.dev_attr.attr,
+	&sensor_dev_attr_in12_max.dev_attr.attr,
+	&sensor_dev_attr_in13_max.dev_attr.attr,
+	&sensor_dev_attr_in14_max.dev_attr.attr,
+	&sensor_dev_attr_in15_max.dev_attr.attr,
+	&sensor_dev_attr_in16_max.dev_attr.attr,
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	&sensor_dev_attr_temp2_input.dev_attr.attr,
+	&sensor_dev_attr_temp3_input.dev_attr.attr,
+	&sensor_dev_attr_temp1_min.dev_attr.attr,
+	&sensor_dev_attr_temp2_min.dev_attr.attr,
+	&sensor_dev_attr_temp3_min.dev_attr.attr,
+	&sensor_dev_attr_temp1_max.dev_attr.attr,
+	&sensor_dev_attr_temp2_max.dev_attr.attr,
+	&sensor_dev_attr_temp3_max.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_base.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_base.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_base.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_boost.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_boost.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_boost.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_boost_hyst.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_boost_hyst.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_boost_hyst.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset1.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset2.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset3.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset4.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset5.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset6.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset7.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset8.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset9.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset10.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset11.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset12.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset1.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset2.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset3.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset4.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset5.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset6.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset7.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset8.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset9.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset10.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset11.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset12.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset1.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset2.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset3.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset4.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset5.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset6.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset7.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset8.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset9.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset10.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset11.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset12.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_pwm_min.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_pwm_min.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_pwm_min.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_offset_hyst.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_offset_hyst.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_offset_hyst.dev_attr.attr,
+	&sensor_dev_attr_fan1_input.dev_attr.attr,
+	&sensor_dev_attr_fan2_input.dev_attr.attr,
+	&sensor_dev_attr_fan3_input.dev_attr.attr,
+	&sensor_dev_attr_fan4_input.dev_attr.attr,
+	&sensor_dev_attr_fan1_min.dev_attr.attr,
+	&sensor_dev_attr_fan2_min.dev_attr.attr,
+	&sensor_dev_attr_fan3_min.dev_attr.attr,
+	&sensor_dev_attr_fan4_min.dev_attr.attr,
+	&sensor_dev_attr_fan1_smart_tach.dev_attr.attr,
+	&sensor_dev_attr_fan2_smart_tach.dev_attr.attr,
+	&sensor_dev_attr_fan3_smart_tach.dev_attr.attr,
+	&sensor_dev_attr_fan4_smart_tach.dev_attr.attr,
+	&sensor_dev_attr_pwm1.dev_attr.attr,
+	&sensor_dev_attr_pwm2.dev_attr.attr,
+	&sensor_dev_attr_pwm1_enable.dev_attr.attr,
+	&sensor_dev_attr_pwm2_enable.dev_attr.attr,
+	&sensor_dev_attr_pwm1_freq.dev_attr.attr,
+	&sensor_dev_attr_pwm2_freq.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_channels.dev_attr.attr,
+	&sensor_dev_attr_pwm2_auto_channels.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_spinup_min.dev_attr.attr,
+	&sensor_dev_attr_pwm2_auto_spinup_min.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_spinup_time.dev_attr.attr,
+	&sensor_dev_attr_pwm2_auto_spinup_time.dev_attr.attr,
+	&dev_attr_pwm_auto_prochot_ramp.attr,
+	&dev_attr_pwm_auto_vrdhot_ramp.attr,
+	&sensor_dev_attr_vid1.dev_attr.attr,
+	&sensor_dev_attr_vid2.dev_attr.attr,
+	&sensor_dev_attr_prochot1.dev_attr.attr,
+	&sensor_dev_attr_prochot2.dev_attr.attr,
+	&sensor_dev_attr_prochot1_avg.dev_attr.attr,
+	&sensor_dev_attr_prochot2_avg.dev_attr.attr,
+	&sensor_dev_attr_prochot1_max.dev_attr.attr,
+	&sensor_dev_attr_prochot2_max.dev_attr.attr,
+	&sensor_dev_attr_prochot1_override.dev_attr.attr,
+	&sensor_dev_attr_prochot2_override.dev_attr.attr,
+	&sensor_dev_attr_prochot1_interval.dev_attr.attr,
+	&sensor_dev_attr_prochot2_interval.dev_attr.attr,
+	&dev_attr_prochot_override_duty_cycle.attr,
+	&dev_attr_prochot_short.attr,
+	&sensor_dev_attr_vrdhot1.dev_attr.attr,
+	&sensor_dev_attr_vrdhot2.dev_attr.attr,
+	&dev_attr_gpio.attr,
+	&dev_attr_alarms.attr,
+	NULL
+};
+
+static struct attribute_group lm93_attr_grp = {
+	.attrs = lm93_attrs,
+};
+
+static void lm93_init_client(struct i2c_client *client)
+{
+	int i;
+	u8 reg;
+
+	/* configure VID pin input thresholds */
+	reg = lm93_read_byte(client, LM93_REG_GPI_VID_CTL);
+	lm93_write_byte(client, LM93_REG_GPI_VID_CTL,
+			reg | (vid_agtl ? 0x03 : 0x00));
+
+	if (init) {
+		/* enable #ALERT pin */
+		reg = lm93_read_byte(client, LM93_REG_CONFIG);
+		lm93_write_byte(client, LM93_REG_CONFIG, reg | 0x08);
+
+		/* enable ASF mode for BMC status registers */
+		reg = lm93_read_byte(client, LM93_REG_STATUS_CONTROL);
+		lm93_write_byte(client, LM93_REG_STATUS_CONTROL, reg | 0x02);
+
+		/* set sleep state to S0 */
+		lm93_write_byte(client, LM93_REG_SLEEP_CONTROL, 0);
+
+		/* unmask #VRDHOT and dynamic VCCP (if nec) error events */
+		reg = lm93_read_byte(client, LM93_REG_MISC_ERR_MASK);
+		reg &= ~0x03;
+		reg &= ~(vccp_limit_type[0] ? 0x10 : 0);
+		reg &= ~(vccp_limit_type[1] ? 0x20 : 0);
+		lm93_write_byte(client, LM93_REG_MISC_ERR_MASK, reg);
+	}
+
+	/* start monitoring */
+	reg = lm93_read_byte(client, LM93_REG_CONFIG);
+	lm93_write_byte(client, LM93_REG_CONFIG, reg | 0x01);
+
+	/* spin until ready */
+	for (i=0; i<20; i++) {
+		msleep(10);
+		if ((lm93_read_byte(client, LM93_REG_CONFIG) & 0x80) == 0x80)
+			return;
+	}
+
+	dev_warn(&client->dev,"timed out waiting for sensor "
+		 "chip to signal ready!\n");
+}
+
+static int lm93_detect(struct i2c_adapter *adapter, int address, int kind)
+{
+	struct lm93_data *data;
+	struct i2c_client *client;
+
+	int err = -ENODEV, func;
+	void (*update)(struct lm93_data *, struct i2c_client *);
+
+	/* choose update routine based on bus capabilities */
+	func = i2c_get_functionality(adapter);
+	if ( ((LM93_SMBUS_FUNC_FULL & func) == LM93_SMBUS_FUNC_FULL) &&
+			(!disable_block) ) {
+		dev_dbg(&adapter->dev,"using SMBus block data transactions\n");
+		update = lm93_update_client_full;
+	} else if ((LM93_SMBUS_FUNC_MIN & func) == LM93_SMBUS_FUNC_MIN) {
+		dev_dbg(&adapter->dev,"disabled SMBus block data "
+			"transactions\n");
+		update = lm93_update_client_min;
+	} else {
+		dev_dbg(&adapter->dev,"detect failed, "
+			"smbus byte and/or word data not supported!\n");
+		goto err_out;
+	}
+
+	/* OK. For now, we presume we have a valid client. We now create the
+	   client structure, even though we cannot fill it completely yet.
+	   But it allows us to access lm78_{read,write}_value. */
+
+	if ( !(data = kzalloc(sizeof(struct lm93_data), GFP_KERNEL))) {
+		dev_dbg(&adapter->dev,"out of memory!\n");
+		err = -ENOMEM;
+		goto err_out;
+	}
+
+	client = &data->client;
+	i2c_set_clientdata(client, data);
+	client->addr = address;
+	client->adapter = adapter;
+	client->driver = &lm93_driver;
+
+	/* detection */
+	if (kind < 0) {
+		int mfr = lm93_read_byte(client, LM93_REG_MFR_ID);
+
+		if (mfr != 0x01) {
+			dev_dbg(&adapter->dev,"detect failed, "
+				"bad manufacturer id 0x%02x!\n", mfr);
+			goto err_free;
+		}
+	}
+
+	if (kind <= 0) {
+		int ver = lm93_read_byte(client, LM93_REG_VER);
+
+		if ((ver == LM93_MFR_ID) || (ver == LM93_MFR_ID_PROTOTYPE)) {
+			kind = lm93;
+		} else {
+			dev_dbg(&adapter->dev,"detect failed, "
+				"bad version id 0x%02x!\n", ver);
+			if (kind == 0)
+				dev_dbg(&adapter->dev,
+					"(ignored 'force' parameter)\n");
+			goto err_free;
+		}
+	}
+
+	/* fill in remaining client fields */
+	strlcpy(client->name, "lm93", I2C_NAME_SIZE);
+	dev_dbg(&adapter->dev,"loading %s at %d,0x%02x\n",
+		client->name, i2c_adapter_id(client->adapter),
+		client->addr);
+
+	/* housekeeping */
+	data->valid = 0;
+	data->update = update;
+	mutex_init(&data->update_lock);
+
+	/* tell the I2C layer a new client has arrived */
+	if ((err = i2c_attach_client(client)))
+		goto err_free;
+
+	/* initialize the chip */
+	lm93_init_client(client);
+
+	err = sysfs_create_group(&client->dev.kobj, &lm93_attr_grp);
+	if (err)
+		goto err_detach;
+
+	/* Register hwmon driver class */
+	data->class_dev = hwmon_device_register(&client->dev);
+	if ( !IS_ERR(data->class_dev))
+		return 0;
+
+	err = PTR_ERR(data->class_dev);
+	dev_err(&client->dev, "error registering hwmon device.\n");
+	sysfs_remove_group(&client->dev.kobj, &lm93_attr_grp);
+err_detach:
+	i2c_detach_client(client);
+err_free:
+	kfree(data);
+err_out:
+	return err;
+}
+
+/* This function is called when:
+     * lm93_driver is inserted (when this module is loaded), for each
+       available adapter
+     * when a new adapter is inserted (and lm93_driver is still present) */
+static int lm93_attach_adapter(struct i2c_adapter *adapter)
+{
+	return i2c_probe(adapter, &addr_data, lm93_detect);
+}
+
+static int lm93_detach_client(struct i2c_client *client)
+{
+	struct lm93_data *data = i2c_get_clientdata(client);
+	int err = 0;
+
+	hwmon_device_unregister(data->class_dev);
+	sysfs_remove_group(&client->dev.kobj, &lm93_attr_grp);
+
+	err = i2c_detach_client(client);
+	if (!err)
+		kfree(data);
+	return err;
+}
+
+static struct i2c_driver lm93_driver = {
+	.driver = {
+		.name	= "lm93",
+	},
+	.attach_adapter	= lm93_attach_adapter,
+	.detach_client	= lm93_detach_client,
+};
+
+static int __init lm93_init(void)
+{
+	return i2c_add_driver(&lm93_driver);
+}
+
+static void __exit lm93_exit(void)
+{
+	i2c_del_driver(&lm93_driver);
+}
+
+MODULE_AUTHOR("Mark M. Hoffman <mhoffman@lightlink.com>, "
+		"Hans J. Koch <hjk@linutronix.de");
+MODULE_DESCRIPTION("LM93 driver");
+MODULE_LICENSE("GPL");
+
+module_init(lm93_init);
+module_exit(lm93_exit);
diff --git a/drivers/hwmon/pc87360.c b/drivers/hwmon/pc87360.c
index c8a21be..cb72526c 100644
--- a/drivers/hwmon/pc87360.c
+++ b/drivers/hwmon/pc87360.c
@@ -1,7 +1,7 @@
 /*
  *  pc87360.c - Part of lm_sensors, Linux kernel modules
  *              for hardware monitoring
- *  Copyright (C) 2004 Jean Delvare <khali@linux-fr.org>
+ *  Copyright (C) 2004, 2007 Jean Delvare <khali@linux-fr.org>
  *
  *  Copied from smsc47m1.c:
  *  Copyright (C) 2002 Mark D. Studebaker <mdsxyz123@yahoo.com>
@@ -37,8 +37,7 @@
 #include <linux/init.h>
 #include <linux/slab.h>
 #include <linux/jiffies.h>
-#include <linux/i2c.h>
-#include <linux/i2c-isa.h>
+#include <linux/platform_device.h>
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
 #include <linux/hwmon-vid.h>
@@ -47,12 +46,10 @@
 #include <asm/io.h>
 
 static u8 devid;
-static unsigned short address;
+static struct platform_device *pdev;
 static unsigned short extra_isa[3];
 static u8 confreg[4];
 
-enum chips { any_chip, pc87360, pc87363, pc87364, pc87365, pc87366 };
-
 static int init = 1;
 module_param(init, int, 0);
 MODULE_PARM_DESC(init,
@@ -178,11 +175,11 @@
 					 ((val) + 500) / 1000)
 
 /*
- * Client data (each client gets its own)
+ * Device data
  */
 
 struct pc87360_data {
-	struct i2c_client client;
+	const char *name;
 	struct class_device *class_dev;
 	struct mutex lock;
 	struct mutex update_lock;
@@ -222,27 +219,28 @@
  * Functions declaration
  */
 
-static int pc87360_detect(struct i2c_adapter *adapter);
-static int pc87360_detach_client(struct i2c_client *client);
+static int pc87360_probe(struct platform_device *pdev);
+static int pc87360_remove(struct platform_device *pdev);
 
 static int pc87360_read_value(struct pc87360_data *data, u8 ldi, u8 bank,
 			      u8 reg);
 static void pc87360_write_value(struct pc87360_data *data, u8 ldi, u8 bank,
 				u8 reg, u8 value);
-static void pc87360_init_client(struct i2c_client *client, int use_thermistors);
+static void pc87360_init_device(struct platform_device *pdev,
+				int use_thermistors);
 static struct pc87360_data *pc87360_update_device(struct device *dev);
 
 /*
- * Driver data (common to all clients)
+ * Driver data
  */
 
-static struct i2c_driver pc87360_driver = {
+static struct platform_driver pc87360_driver = {
 	.driver = {
 		.owner	= THIS_MODULE,
 		.name	= "pc87360",
 	},
-	.attach_adapter	= pc87360_detect,
-	.detach_client	= pc87360_detach_client,
+	.probe		= pc87360_probe,
+	.remove		= __devexit_p(pc87360_remove),
 };
 
 /*
@@ -281,8 +279,7 @@
 	size_t count)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
-	struct i2c_client *client = to_i2c_client(dev);
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	long fan_min = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
@@ -347,8 +344,7 @@
 	size_t count)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
-	struct i2c_client *client = to_i2c_client(dev);
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	long val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
@@ -410,8 +406,7 @@
 	size_t count)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
-	struct i2c_client *client = to_i2c_client(dev);
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	long val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
@@ -425,8 +420,7 @@
 	size_t count)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
-	struct i2c_client *client = to_i2c_client(dev);
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	long val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
@@ -511,8 +505,7 @@
 }
 static ssize_t set_vrm(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	data->vrm = simple_strtoul(buf, NULL, 10);
 	return count;
 }
@@ -584,8 +577,7 @@
 	size_t count)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
-	struct i2c_client *client = to_i2c_client(dev);
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	long val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
@@ -599,8 +591,7 @@
 	size_t count)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
-	struct i2c_client *client = to_i2c_client(dev);
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	long val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
@@ -614,8 +605,7 @@
 	size_t count)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
-	struct i2c_client *client = to_i2c_client(dev);
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	long val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
@@ -715,8 +705,7 @@
 	size_t count)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
-	struct i2c_client *client = to_i2c_client(dev);
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	long val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
@@ -730,8 +719,7 @@
 	size_t count)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
-	struct i2c_client *client = to_i2c_client(dev);
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	long val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
@@ -745,8 +733,7 @@
 	size_t count)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
-	struct i2c_client *client = to_i2c_client(dev);
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	long val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
@@ -818,6 +805,14 @@
 	.attrs = pc8736x_temp_attr_array,
 };
 
+static ssize_t show_name(struct device *dev, struct device_attribute
+			 *devattr, char *buf)
+{
+	struct pc87360_data *data = dev_get_drvdata(dev);
+	return sprintf(buf, "%s\n", data->name);
+}
+static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
+
 /*
  * Device detection, registration and update
  */
@@ -912,28 +907,18 @@
 	return 0;
 }
 
-static int pc87360_detect(struct i2c_adapter *adapter)
+static int __devinit pc87360_probe(struct platform_device *pdev)
 {
 	int i;
-	struct i2c_client *client;
 	struct pc87360_data *data;
 	int err = 0;
 	const char *name = "pc87360";
 	int use_thermistors = 0;
-	struct device *dev;
+	struct device *dev = &pdev->dev;
 
 	if (!(data = kzalloc(sizeof(struct pc87360_data), GFP_KERNEL)))
 		return -ENOMEM;
 
-	client = &data->client;
-	dev = &client->dev;
-	i2c_set_clientdata(client, data);
-	client->addr = address;
-	mutex_init(&data->lock);
-	client->adapter = adapter;
-	client->driver = &pc87360_driver;
-	client->flags = 0;
-
 	data->fannr = 2;
 	data->innr = 0;
 	data->tempnr = 0;
@@ -960,15 +945,17 @@
 		break;
 	}
 
-	strlcpy(client->name, name, sizeof(client->name));
+	data->name = name;
 	data->valid = 0;
+	mutex_init(&data->lock);
 	mutex_init(&data->update_lock);
+	platform_set_drvdata(pdev, data);
 
 	for (i = 0; i < 3; i++) {
 		if (((data->address[i] = extra_isa[i]))
 		 && !request_region(extra_isa[i], PC87360_EXTENT,
 		 		    pc87360_driver.driver.name)) {
-			dev_err(&client->dev, "Region 0x%x-0x%x already "
+			dev_err(dev, "Region 0x%x-0x%x already "
 				"in use!\n", extra_isa[i],
 				extra_isa[i]+PC87360_EXTENT-1);
 			for (i--; i >= 0; i--)
@@ -982,9 +969,6 @@
 	if (data->fannr)
 		data->fan_conf = confreg[0] | (confreg[1] << 8);
 
-	if ((err = i2c_attach_client(client)))
-		goto ERROR2;
-
 	/* Use the correct reference voltage
 	   Unless both the VLM and the TMS logical devices agree to
 	   use an external Vref, the internal one is used. */
@@ -996,7 +980,7 @@
 						PC87365_REG_TEMP_CONFIG);
 		}
 		data->in_vref = (i&0x02) ? 3025 : 2966;
-		dev_dbg(&client->dev, "Using %s reference voltage\n",
+		dev_dbg(dev, "Using %s reference voltage\n",
 			(i&0x02) ? "external" : "internal");
 
 		data->vid_conf = confreg[3];
@@ -1015,18 +999,18 @@
 		if (devid == 0xe9 && data->address[1]) /* PC87366 */
 			use_thermistors = confreg[2] & 0x40;
 
-		pc87360_init_client(client, use_thermistors);
+		pc87360_init_device(pdev, use_thermistors);
 	}
 
 	/* Register all-or-nothing sysfs groups */
 
 	if (data->innr &&
-	    (err = sysfs_create_group(&client->dev.kobj,
+	    (err = sysfs_create_group(&dev->kobj,
 				      &pc8736x_vin_group)))
 		goto ERROR3;
 
 	if (data->innr == 14 &&
-	    (err = sysfs_create_group(&client->dev.kobj,
+	    (err = sysfs_create_group(&dev->kobj,
 				      &pc8736x_therm_group)))
 		goto ERROR3;
 
@@ -1067,7 +1051,10 @@
 			goto ERROR3;
 	}
 
-	data->class_dev = hwmon_device_register(&client->dev);
+	if ((err = device_create_file(dev, &dev_attr_name)))
+		goto ERROR3;
+
+	data->class_dev = hwmon_device_register(dev);
 	if (IS_ERR(data->class_dev)) {
 		err = PTR_ERR(data->class_dev);
 		goto ERROR3;
@@ -1075,14 +1062,12 @@
 	return 0;
 
 ERROR3:
+	device_remove_file(dev, &dev_attr_name);
 	/* can still remove groups whose members were added individually */
-	sysfs_remove_group(&client->dev.kobj, &pc8736x_temp_group);
-	sysfs_remove_group(&client->dev.kobj, &pc8736x_fan_group);
-	sysfs_remove_group(&client->dev.kobj, &pc8736x_therm_group);
-	sysfs_remove_group(&client->dev.kobj, &pc8736x_vin_group);
-
-	i2c_detach_client(client);
-ERROR2:
+	sysfs_remove_group(&dev->kobj, &pc8736x_temp_group);
+	sysfs_remove_group(&dev->kobj, &pc8736x_fan_group);
+	sysfs_remove_group(&dev->kobj, &pc8736x_therm_group);
+	sysfs_remove_group(&dev->kobj, &pc8736x_vin_group);
 	for (i = 0; i < 3; i++) {
 		if (data->address[i]) {
 			release_region(data->address[i], PC87360_EXTENT);
@@ -1093,20 +1078,18 @@
 	return err;
 }
 
-static int pc87360_detach_client(struct i2c_client *client)
+static int __devexit pc87360_remove(struct platform_device *pdev)
 {
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = platform_get_drvdata(pdev);
 	int i;
 
 	hwmon_device_unregister(data->class_dev);
 
-	sysfs_remove_group(&client->dev.kobj, &pc8736x_temp_group);
-	sysfs_remove_group(&client->dev.kobj, &pc8736x_fan_group);
-	sysfs_remove_group(&client->dev.kobj, &pc8736x_therm_group);
-	sysfs_remove_group(&client->dev.kobj, &pc8736x_vin_group);
-
-	if ((i = i2c_detach_client(client)))
-		return i;
+	device_remove_file(&pdev->dev, &dev_attr_name);
+	sysfs_remove_group(&pdev->dev.kobj, &pc8736x_temp_group);
+	sysfs_remove_group(&pdev->dev.kobj, &pc8736x_fan_group);
+	sysfs_remove_group(&pdev->dev.kobj, &pc8736x_therm_group);
+	sysfs_remove_group(&pdev->dev.kobj, &pc8736x_vin_group);
 
 	for (i = 0; i < 3; i++) {
 		if (data->address[i]) {
@@ -1144,9 +1127,10 @@
 	mutex_unlock(&(data->lock));
 }
 
-static void pc87360_init_client(struct i2c_client *client, int use_thermistors)
+static void pc87360_init_device(struct platform_device *pdev,
+				int use_thermistors)
 {
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = platform_get_drvdata(pdev);
 	int i, nr;
 	const u8 init_in[14] = { 2, 2, 2, 2, 2, 2, 2, 1, 1, 3, 1, 2, 2, 2 };
 	const u8 init_temp[3] = { 2, 2, 1 };
@@ -1155,7 +1139,7 @@
 	if (init >= 2 && data->innr) {
 		reg = pc87360_read_value(data, LD_IN, NO_BANK,
 					 PC87365_REG_IN_CONVRATE);
-		dev_info(&client->dev, "VLM conversion set to "
+		dev_info(&pdev->dev, "VLM conversion set to "
 			 "1s period, 160us delay\n");
 		pc87360_write_value(data, LD_IN, NO_BANK,
 				    PC87365_REG_IN_CONVRATE,
@@ -1169,7 +1153,7 @@
 			reg = pc87360_read_value(data, LD_IN, i,
 						 PC87365_REG_IN_STATUS);
 			if (!(reg & 0x01)) {
-				dev_dbg(&client->dev, "Forcibly "
+				dev_dbg(&pdev->dev, "Forcibly "
 					"enabling in%d\n", i);
 				pc87360_write_value(data, LD_IN, i,
 						    PC87365_REG_IN_STATUS,
@@ -1193,7 +1177,7 @@
 			reg = pc87360_read_value(data, LD_TEMP, i,
 						 PC87365_REG_TEMP_STATUS);
 			if (!(reg & 0x01)) {
-				dev_dbg(&client->dev, "Forcibly "
+				dev_dbg(&pdev->dev, "Forcibly "
 					"enabling temp%d\n", i+1);
 				pc87360_write_value(data, LD_TEMP, i,
 						    PC87365_REG_TEMP_STATUS,
@@ -1210,7 +1194,7 @@
 				reg = pc87360_read_value(data, LD_TEMP,
 				      (i-11)/2, PC87365_REG_TEMP_STATUS);
 				if (reg & 0x01) {
-					dev_dbg(&client->dev, "Skipping "
+					dev_dbg(&pdev->dev, "Skipping "
 						"temp%d, pin already in use "
 						"by temp%d\n", i-7, (i-11)/2);
 					continue;
@@ -1220,7 +1204,7 @@
 				reg = pc87360_read_value(data, LD_IN, i,
 							 PC87365_REG_IN_STATUS);
 				if (!(reg & 0x01)) {
-					dev_dbg(&client->dev, "Forcibly "
+					dev_dbg(&pdev->dev, "Forcibly "
 						"enabling temp%d\n", i-7);
 					pc87360_write_value(data, LD_IN, i,
 						PC87365_REG_TEMP_STATUS,
@@ -1234,7 +1218,7 @@
 		reg = pc87360_read_value(data, LD_IN, NO_BANK,
 					 PC87365_REG_IN_CONFIG);
 		if (reg & 0x01) {
-			dev_dbg(&client->dev, "Forcibly "
+			dev_dbg(&pdev->dev, "Forcibly "
 				"enabling monitoring (VLM)\n");
 			pc87360_write_value(data, LD_IN, NO_BANK,
 					    PC87365_REG_IN_CONFIG,
@@ -1246,7 +1230,7 @@
 		reg = pc87360_read_value(data, LD_TEMP, NO_BANK,
 					 PC87365_REG_TEMP_CONFIG);
 		if (reg & 0x01) {
-			dev_dbg(&client->dev, "Forcibly enabling "
+			dev_dbg(&pdev->dev, "Forcibly enabling "
 				"monitoring (TMS)\n");
 			pc87360_write_value(data, LD_TEMP, NO_BANK,
 					    PC87365_REG_TEMP_CONFIG,
@@ -1268,9 +1252,9 @@
 	}
 }
 
-static void pc87360_autodiv(struct i2c_client *client, int nr)
+static void pc87360_autodiv(struct device *dev, int nr)
 {
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	u8 old_min = data->fan_min[nr];
 
 	/* Increase clock divider if needed and possible */
@@ -1280,7 +1264,7 @@
 			data->fan_status[nr] += 0x20;
 			data->fan_min[nr] >>= 1;
 			data->fan[nr] >>= 1;
-			dev_dbg(&client->dev, "Increasing "
+			dev_dbg(dev, "Increasing "
 				"clock divider to %d for fan %d\n",
 				FAN_DIV_FROM_REG(data->fan_status[nr]), nr+1);
 		}
@@ -1292,7 +1276,7 @@
 			data->fan_status[nr] -= 0x20;
 			data->fan_min[nr] <<= 1;
 			data->fan[nr] <<= 1;
-			dev_dbg(&client->dev, "Decreasing "
+			dev_dbg(dev, "Decreasing "
 				"clock divider to %d for fan %d\n",
 				FAN_DIV_FROM_REG(data->fan_status[nr]),
 				nr+1);
@@ -1309,14 +1293,13 @@
 
 static struct pc87360_data *pc87360_update_device(struct device *dev)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct pc87360_data *data = i2c_get_clientdata(client);
+	struct pc87360_data *data = dev_get_drvdata(dev);
 	u8 i;
 
 	mutex_lock(&data->update_lock);
 
 	if (time_after(jiffies, data->last_updated + HZ * 2) || !data->valid) {
-		dev_dbg(&client->dev, "Data update\n");
+		dev_dbg(dev, "Data update\n");
 
 		/* Fans */
 		for (i = 0; i < data->fannr; i++) {
@@ -1330,7 +1313,7 @@
 						   LD_FAN, NO_BANK,
 						   PC87360_REG_FAN_MIN(i));
 				/* Change clock divider if needed */
-				pc87360_autodiv(client, i);
+				pc87360_autodiv(dev, i);
 				/* Clear bits and write new divider */
 				pc87360_write_value(data, LD_FAN, NO_BANK,
 						    PC87360_REG_FAN_STATUS(i),
@@ -1418,9 +1401,53 @@
 	return data;
 }
 
+static int __init pc87360_device_add(unsigned short address)
+{
+	struct resource res = {
+		.name	= "pc87360",
+		.flags	= IORESOURCE_IO,
+	};
+	int err, i;
+
+	pdev = platform_device_alloc("pc87360", address);
+	if (!pdev) {
+		err = -ENOMEM;
+		printk(KERN_ERR "pc87360: Device allocation failed\n");
+		goto exit;
+	}
+
+	for (i = 0; i < 3; i++) {
+		if (!extra_isa[i])
+			continue;
+		res.start = extra_isa[i];
+		res.end = extra_isa[i] + PC87360_EXTENT - 1;
+		err = platform_device_add_resources(pdev, &res, 1);
+		if (err) {
+			printk(KERN_ERR "pc87360: Device resource[%d] "
+			       "addition failed (%d)\n", i, err);
+			goto exit_device_put;
+		}
+	}
+
+	err = platform_device_add(pdev);
+	if (err) {
+		printk(KERN_ERR "pc87360: Device addition failed (%d)\n",
+		       err);
+		goto exit_device_put;
+	}
+
+	return 0;
+
+exit_device_put:
+	platform_device_put(pdev);
+exit:
+	return err;
+}
+
 static int __init pc87360_init(void)
 {
-	int i;
+	int err, i;
+	unsigned short address = 0;
 
 	if (pc87360_find(0x2e, &devid, extra_isa)
 	 && pc87360_find(0x4e, &devid, extra_isa)) {
@@ -1443,12 +1470,27 @@
 		return -ENODEV;
 	}
 
-	return i2c_isa_add_driver(&pc87360_driver);
+	err = platform_driver_register(&pc87360_driver);
+	if (err)
+		goto exit;
+
+	/* Sets global pdev as a side effect */
+	err = pc87360_device_add(address);
+	if (err)
+		goto exit_driver;
+
+	return 0;
+
+ exit_driver:
+	platform_driver_unregister(&pc87360_driver);
+ exit:
+	return err;
 }
 
 static void __exit pc87360_exit(void)
 {
-	i2c_isa_del_driver(&pc87360_driver);
+	platform_device_unregister(pdev);
+	platform_driver_unregister(&pc87360_driver);
 }
 
 
diff --git a/drivers/hwmon/pc87427.c b/drivers/hwmon/pc87427.c
index 29354fa..2915bc4 100644
--- a/drivers/hwmon/pc87427.c
+++ b/drivers/hwmon/pc87427.c
@@ -484,7 +484,6 @@
 	struct resource *res;
 	int i;
 
-	platform_set_drvdata(pdev, NULL);
 	hwmon_device_unregister(data->class_dev);
 	device_remove_file(&pdev->dev, &dev_attr_name);
 	for (i = 0; i < 8; i++) {
@@ -492,6 +491,7 @@
 			continue;
 		sysfs_remove_group(&pdev->dev.kobj, &pc87427_group_fan[i]);
 	}
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 
 	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
diff --git a/drivers/hwmon/sis5595.c b/drivers/hwmon/sis5595.c
index 3f40026..83321b2 100644
--- a/drivers/hwmon/sis5595.c
+++ b/drivers/hwmon/sis5595.c
@@ -54,9 +54,9 @@
 #include <linux/slab.h>
 #include <linux/ioport.h>
 #include <linux/pci.h>
-#include <linux/i2c.h>
-#include <linux/i2c-isa.h>
+#include <linux/platform_device.h>
 #include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
 #include <linux/err.h>
 #include <linux/init.h>
 #include <linux/jiffies.h>
@@ -72,17 +72,13 @@
 MODULE_PARM_DESC(force_addr,
 		 "Initialize the base address of the sensors");
 
-/* Device address
-   Note that we can't determine the ISA address until we have initialized
-   our module */
-static unsigned short address;
+static struct platform_device *pdev;
 
 /* Many SIS5595 constants specified below */
 
 /* Length of ISA address segment */
 #define SIS5595_EXTENT 8
 /* PCI Config Registers */
-#define SIS5595_REVISION_REG 0x08
 #define SIS5595_BASE_REG 0x68
 #define SIS5595_PIN_REG 0x7A
 #define SIS5595_ENABLE_REG 0x7B
@@ -165,7 +161,8 @@
 /* For each registered chip, we need to keep some data in memory.
    The structure is dynamically allocated. */
 struct sis5595_data {
-	struct i2c_client client;
+	unsigned short addr;
+	const char *name;
 	struct class_device *class_dev;
 	struct mutex lock;
 
@@ -189,102 +186,88 @@
 
 static struct pci_dev *s_bridge;	/* pointer to the (only) sis5595 */
 
-static int sis5595_detect(struct i2c_adapter *adapter);
-static int sis5595_detach_client(struct i2c_client *client);
+static int sis5595_probe(struct platform_device *pdev);
+static int sis5595_remove(struct platform_device *pdev);
 
-static int sis5595_read_value(struct i2c_client *client, u8 reg);
-static int sis5595_write_value(struct i2c_client *client, u8 reg, u8 value);
+static int sis5595_read_value(struct sis5595_data *data, u8 reg);
+static void sis5595_write_value(struct sis5595_data *data, u8 reg, u8 value);
 static struct sis5595_data *sis5595_update_device(struct device *dev);
-static void sis5595_init_client(struct i2c_client *client);
+static void sis5595_init_device(struct sis5595_data *data);
 
-static struct i2c_driver sis5595_driver = {
+static struct platform_driver sis5595_driver = {
 	.driver = {
 		.owner	= THIS_MODULE,
 		.name	= "sis5595",
 	},
-	.attach_adapter	= sis5595_detect,
-	.detach_client	= sis5595_detach_client,
+	.probe		= sis5595_probe,
+	.remove		= __devexit_p(sis5595_remove),
 };
 
 /* 4 Voltages */
-static ssize_t show_in(struct device *dev, char *buf, int nr)
+static ssize_t show_in(struct device *dev, struct device_attribute *da,
+		       char *buf)
 {
 	struct sis5595_data *data = sis5595_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%d\n", IN_FROM_REG(data->in[nr]));
 }
 
-static ssize_t show_in_min(struct device *dev, char *buf, int nr)
+static ssize_t show_in_min(struct device *dev, struct device_attribute *da,
+			   char *buf)
 {
 	struct sis5595_data *data = sis5595_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%d\n", IN_FROM_REG(data->in_min[nr]));
 }
 
-static ssize_t show_in_max(struct device *dev, char *buf, int nr)
+static ssize_t show_in_max(struct device *dev, struct device_attribute *da,
+			   char *buf)
 {
 	struct sis5595_data *data = sis5595_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%d\n", IN_FROM_REG(data->in_max[nr]));
 }
 
-static ssize_t set_in_min(struct device *dev, const char *buf,
-	       size_t count, int nr)
+static ssize_t set_in_min(struct device *dev, struct device_attribute *da,
+			  const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct sis5595_data *data = i2c_get_clientdata(client);
+	struct sis5595_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->in_min[nr] = IN_TO_REG(val);
-	sis5595_write_value(client, SIS5595_REG_IN_MIN(nr), data->in_min[nr]);
+	sis5595_write_value(data, SIS5595_REG_IN_MIN(nr), data->in_min[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
 
-static ssize_t set_in_max(struct device *dev, const char *buf,
-	       size_t count, int nr)
+static ssize_t set_in_max(struct device *dev, struct device_attribute *da,
+			  const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct sis5595_data *data = i2c_get_clientdata(client);
+	struct sis5595_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->in_max[nr] = IN_TO_REG(val);
-	sis5595_write_value(client, SIS5595_REG_IN_MAX(nr), data->in_max[nr]);
+	sis5595_write_value(data, SIS5595_REG_IN_MAX(nr), data->in_max[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
 
 #define show_in_offset(offset)					\
-static ssize_t							\
-	show_in##offset (struct device *dev, struct device_attribute *attr, char *buf)		\
-{								\
-	return show_in(dev, buf, offset);			\
-}								\
-static DEVICE_ATTR(in##offset##_input, S_IRUGO, 		\
-		show_in##offset, NULL);				\
-static ssize_t							\
-	show_in##offset##_min (struct device *dev, struct device_attribute *attr, char *buf)	\
-{								\
-	return show_in_min(dev, buf, offset);			\
-}								\
-static ssize_t							\
-	show_in##offset##_max (struct device *dev, struct device_attribute *attr, char *buf)	\
-{								\
-	return show_in_max(dev, buf, offset);			\
-}								\
-static ssize_t set_in##offset##_min (struct device *dev, struct device_attribute *attr,	\
-		const char *buf, size_t count)			\
-{								\
-	return set_in_min(dev, buf, count, offset);		\
-}								\
-static ssize_t set_in##offset##_max (struct device *dev, struct device_attribute *attr,	\
-		const char *buf, size_t count)			\
-{								\
-	return set_in_max(dev, buf, count, offset);		\
-}								\
-static DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR,		\
-		show_in##offset##_min, set_in##offset##_min);	\
-static DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR,		\
-		show_in##offset##_max, set_in##offset##_max);
+static SENSOR_DEVICE_ATTR(in##offset##_input, S_IRUGO,		\
+		show_in, NULL, offset);				\
+static SENSOR_DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR,	\
+		show_in_min, set_in_min, offset);		\
+static SENSOR_DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR,	\
+		show_in_max, set_in_max, offset);
 
 show_in_offset(0);
 show_in_offset(1);
@@ -307,13 +290,12 @@
 
 static ssize_t set_temp_over(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct sis5595_data *data = i2c_get_clientdata(client);
+	struct sis5595_data *data = dev_get_drvdata(dev);
 	long val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->temp_over = TEMP_TO_REG(val);
-	sis5595_write_value(client, SIS5595_REG_TEMP_OVER, data->temp_over);
+	sis5595_write_value(data, SIS5595_REG_TEMP_OVER, data->temp_over);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -326,13 +308,12 @@
 
 static ssize_t set_temp_hyst(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct sis5595_data *data = i2c_get_clientdata(client);
+	struct sis5595_data *data = dev_get_drvdata(dev);
 	long val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->temp_hyst = TEMP_TO_REG(val);
-	sis5595_write_value(client, SIS5595_REG_TEMP_HYST, data->temp_hyst);
+	sis5595_write_value(data, SIS5595_REG_TEMP_HYST, data->temp_hyst);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -344,37 +325,47 @@
 		show_temp_hyst, set_temp_hyst);
 
 /* 2 Fans */
-static ssize_t show_fan(struct device *dev, char *buf, int nr)
+static ssize_t show_fan(struct device *dev, struct device_attribute *da,
+			char *buf)
 {
 	struct sis5595_data *data = sis5595_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan[nr],
 		DIV_FROM_REG(data->fan_div[nr])) );
 }
 
-static ssize_t show_fan_min(struct device *dev, char *buf, int nr)
+static ssize_t show_fan_min(struct device *dev, struct device_attribute *da,
+			    char *buf)
 {
 	struct sis5595_data *data = sis5595_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf,"%d\n", FAN_FROM_REG(data->fan_min[nr],
 		DIV_FROM_REG(data->fan_div[nr])) );
 }
 
-static ssize_t set_fan_min(struct device *dev, const char *buf,
-		size_t count, int nr)
+static ssize_t set_fan_min(struct device *dev, struct device_attribute *da,
+			   const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct sis5595_data *data = i2c_get_clientdata(client);
+	struct sis5595_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->fan_min[nr] = FAN_TO_REG(val, DIV_FROM_REG(data->fan_div[nr]));
-	sis5595_write_value(client, SIS5595_REG_FAN_MIN(nr), data->fan_min[nr]);
+	sis5595_write_value(data, SIS5595_REG_FAN_MIN(nr), data->fan_min[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
 
-static ssize_t show_fan_div(struct device *dev, char *buf, int nr)
+static ssize_t show_fan_div(struct device *dev, struct device_attribute *da,
+			    char *buf)
 {
 	struct sis5595_data *data = sis5595_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%d\n", DIV_FROM_REG(data->fan_div[nr]) );
 }
 
@@ -382,11 +373,12 @@
    determined in part by the fan divisor.  This follows the principle of
    least surprise; the user doesn't expect the fan minimum to change just
    because the divisor changed. */
-static ssize_t set_fan_div(struct device *dev, const char *buf,
-	size_t count, int nr)
+static ssize_t set_fan_div(struct device *dev, struct device_attribute *da,
+			   const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct sis5595_data *data = i2c_get_clientdata(client);
+	struct sis5595_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	unsigned long min;
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 	int reg;
@@ -394,7 +386,7 @@
 	mutex_lock(&data->update_lock);
 	min = FAN_FROM_REG(data->fan_min[nr],
 			DIV_FROM_REG(data->fan_div[nr]));
-	reg = sis5595_read_value(client, SIS5595_REG_FANDIV);
+	reg = sis5595_read_value(data, SIS5595_REG_FANDIV);
 
 	switch (val) {
 	case 1: data->fan_div[nr] = 0; break;
@@ -402,7 +394,7 @@
 	case 4: data->fan_div[nr] = 2; break;
 	case 8: data->fan_div[nr] = 3; break;
 	default:
-		dev_err(&client->dev, "fan_div value %ld not "
+		dev_err(dev, "fan_div value %ld not "
 			"supported. Choose one of 1, 2, 4 or 8!\n", val);
 		mutex_unlock(&data->update_lock);
 		return -EINVAL;
@@ -416,55 +408,25 @@
 		reg = (reg & 0x3f) | (data->fan_div[nr] << 6);
 		break;
 	}
-	sis5595_write_value(client, SIS5595_REG_FANDIV, reg);
+	sis5595_write_value(data, SIS5595_REG_FANDIV, reg);
 	data->fan_min[nr] =
 		FAN_TO_REG(min, DIV_FROM_REG(data->fan_div[nr]));
-	sis5595_write_value(client, SIS5595_REG_FAN_MIN(nr), data->fan_min[nr]);
+	sis5595_write_value(data, SIS5595_REG_FAN_MIN(nr), data->fan_min[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
 
 #define show_fan_offset(offset)						\
-static ssize_t show_fan_##offset (struct device *dev, struct device_attribute *attr, char *buf)	\
-{									\
-	return show_fan(dev, buf, offset - 1);			\
-}									\
-static ssize_t show_fan_##offset##_min (struct device *dev, struct device_attribute *attr, char *buf)	\
-{									\
-	return show_fan_min(dev, buf, offset - 1);			\
-}									\
-static ssize_t show_fan_##offset##_div (struct device *dev, struct device_attribute *attr, char *buf)	\
-{									\
-	return show_fan_div(dev, buf, offset - 1);			\
-}									\
-static ssize_t set_fan_##offset##_min (struct device *dev, struct device_attribute *attr,		\
-		const char *buf, size_t count)				\
-{									\
-	return set_fan_min(dev, buf, count, offset - 1);		\
-}									\
-static DEVICE_ATTR(fan##offset##_input, S_IRUGO, show_fan_##offset, NULL);\
-static DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR,		\
-		show_fan_##offset##_min, set_fan_##offset##_min);
+static SENSOR_DEVICE_ATTR(fan##offset##_input, S_IRUGO,			\
+		show_fan, NULL, offset - 1);				\
+static SENSOR_DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR,		\
+		show_fan_min, set_fan_min, offset - 1);			\
+static SENSOR_DEVICE_ATTR(fan##offset##_div, S_IRUGO | S_IWUSR,		\
+		show_fan_div, set_fan_div, offset - 1);
 
 show_fan_offset(1);
 show_fan_offset(2);
 
-static ssize_t set_fan_1_div(struct device *dev, struct device_attribute *attr, const char *buf,
-		size_t count)
-{
-	return set_fan_div(dev, buf, count, 0) ;
-}
-
-static ssize_t set_fan_2_div(struct device *dev, struct device_attribute *attr, const char *buf,
-		size_t count)
-{
-	return set_fan_div(dev, buf, count, 1) ;
-}
-static DEVICE_ATTR(fan1_div, S_IRUGO | S_IWUSR,
-		show_fan_1_div, set_fan_1_div);
-static DEVICE_ATTR(fan2_div, S_IRUGO | S_IWUSR,
-		show_fan_2_div, set_fan_2_div);
-
 /* Alarms */
 static ssize_t show_alarms(struct device *dev, struct device_attribute *attr, char *buf)
 {
@@ -473,28 +435,37 @@
 }
 static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
 
-static struct attribute *sis5595_attributes[] = {
-	&dev_attr_in0_input.attr,
-	&dev_attr_in0_min.attr,
-	&dev_attr_in0_max.attr,
-	&dev_attr_in1_input.attr,
-	&dev_attr_in1_min.attr,
-	&dev_attr_in1_max.attr,
-	&dev_attr_in2_input.attr,
-	&dev_attr_in2_min.attr,
-	&dev_attr_in2_max.attr,
-	&dev_attr_in3_input.attr,
-	&dev_attr_in3_min.attr,
-	&dev_attr_in3_max.attr,
+static ssize_t show_name(struct device *dev, struct device_attribute *attr,
+			 char *buf)
+{
+	struct sis5595_data *data = dev_get_drvdata(dev);
+	return sprintf(buf, "%s\n", data->name);
+}
+static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
 
-	&dev_attr_fan1_input.attr,
-	&dev_attr_fan1_min.attr,
-	&dev_attr_fan1_div.attr,
-	&dev_attr_fan2_input.attr,
-	&dev_attr_fan2_min.attr,
-	&dev_attr_fan2_div.attr,
+static struct attribute *sis5595_attributes[] = {
+	&sensor_dev_attr_in0_input.dev_attr.attr,
+	&sensor_dev_attr_in0_min.dev_attr.attr,
+	&sensor_dev_attr_in0_max.dev_attr.attr,
+	&sensor_dev_attr_in1_input.dev_attr.attr,
+	&sensor_dev_attr_in1_min.dev_attr.attr,
+	&sensor_dev_attr_in1_max.dev_attr.attr,
+	&sensor_dev_attr_in2_input.dev_attr.attr,
+	&sensor_dev_attr_in2_min.dev_attr.attr,
+	&sensor_dev_attr_in2_max.dev_attr.attr,
+	&sensor_dev_attr_in3_input.dev_attr.attr,
+	&sensor_dev_attr_in3_min.dev_attr.attr,
+	&sensor_dev_attr_in3_max.dev_attr.attr,
+
+	&sensor_dev_attr_fan1_input.dev_attr.attr,
+	&sensor_dev_attr_fan1_min.dev_attr.attr,
+	&sensor_dev_attr_fan1_div.dev_attr.attr,
+	&sensor_dev_attr_fan2_input.dev_attr.attr,
+	&sensor_dev_attr_fan2_min.dev_attr.attr,
+	&sensor_dev_attr_fan2_div.dev_attr.attr,
 
 	&dev_attr_alarms.attr,
+	&dev_attr_name.attr,
 	NULL
 };
 
@@ -503,9 +474,9 @@
 };
 
 static struct attribute *sis5595_attributes_opt[] = {
-	&dev_attr_in4_input.attr,
-	&dev_attr_in4_min.attr,
-	&dev_attr_in4_max.attr,
+	&sensor_dev_attr_in4_input.dev_attr.attr,
+	&sensor_dev_attr_in4_min.dev_attr.attr,
+	&sensor_dev_attr_in4_max.dev_attr.attr,
 
 	&dev_attr_temp1_input.attr,
 	&dev_attr_temp1_max.attr,
@@ -518,68 +489,35 @@
 };
  
 /* This is called when the module is loaded */
-static int sis5595_detect(struct i2c_adapter *adapter)
+static int __devinit sis5595_probe(struct platform_device *pdev)
 {
 	int err = 0;
 	int i;
-	struct i2c_client *new_client;
 	struct sis5595_data *data;
+	struct resource *res;
 	char val;
-	u16 a;
 
-	if (force_addr)
-		address = force_addr & ~(SIS5595_EXTENT - 1);
 	/* Reserve the ISA region */
-	if (!request_region(address, SIS5595_EXTENT,
+	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+	if (!request_region(res->start, SIS5595_EXTENT,
 			    sis5595_driver.driver.name)) {
 		err = -EBUSY;
 		goto exit;
 	}
-	if (force_addr) {
-		dev_warn(&adapter->dev, "forcing ISA address 0x%04X\n", address);
-		if (PCIBIOS_SUCCESSFUL !=
-		    pci_write_config_word(s_bridge, SIS5595_BASE_REG, address))
-			goto exit_release;
-		if (PCIBIOS_SUCCESSFUL !=
-		    pci_read_config_word(s_bridge, SIS5595_BASE_REG, &a))
-			goto exit_release;
-		if ((a & ~(SIS5595_EXTENT - 1)) != address)
-			/* doesn't work for some chips? */
-			goto exit_release;
-	}
-
-	if (PCIBIOS_SUCCESSFUL !=
-	    pci_read_config_byte(s_bridge, SIS5595_ENABLE_REG, &val)) {
-		goto exit_release;
-	}
-	if ((val & 0x80) == 0) {
-		if (PCIBIOS_SUCCESSFUL !=
-		    pci_write_config_byte(s_bridge, SIS5595_ENABLE_REG,
-					  val | 0x80))
-			goto exit_release;
-		if (PCIBIOS_SUCCESSFUL !=
-		    pci_read_config_byte(s_bridge, SIS5595_ENABLE_REG, &val))
-			goto exit_release;
-		if ((val & 0x80) == 0) 
-			/* doesn't work for some chips! */
-			goto exit_release;
-	}
 
 	if (!(data = kzalloc(sizeof(struct sis5595_data), GFP_KERNEL))) {
 		err = -ENOMEM;
 		goto exit_release;
 	}
 
-	new_client = &data->client;
-	new_client->addr = address;
 	mutex_init(&data->lock);
-	i2c_set_clientdata(new_client, data);
-	new_client->adapter = adapter;
-	new_client->driver = &sis5595_driver;
-	new_client->flags = 0;
+	mutex_init(&data->update_lock);
+	data->addr = res->start;
+	data->name = "sis5595";
+	platform_set_drvdata(pdev, data);
 
 	/* Check revision and pin registers to determine whether 4 or 5 voltages */
-	pci_read_config_byte(s_bridge, SIS5595_REVISION_REG, &(data->revision));
+	pci_read_config_byte(s_bridge, PCI_REVISION_ID, &data->revision);
 	/* 4 voltages, 1 temp */
 	data->maxins = 3;
 	if (data->revision >= REV2MIN) {
@@ -589,47 +527,37 @@
 			data->maxins = 4;
 	}
 	
-	/* Fill in the remaining client fields and put it into the global list */
-	strlcpy(new_client->name, "sis5595", I2C_NAME_SIZE);
-
-	data->valid = 0;
-	mutex_init(&data->update_lock);
-
-	/* Tell the I2C layer a new client has arrived */
-	if ((err = i2c_attach_client(new_client)))
-		goto exit_free;
-	
 	/* Initialize the SIS5595 chip */
-	sis5595_init_client(new_client);
+	sis5595_init_device(data);
 
 	/* A few vars need to be filled upon startup */
 	for (i = 0; i < 2; i++) {
-		data->fan_min[i] = sis5595_read_value(new_client,
+		data->fan_min[i] = sis5595_read_value(data,
 					SIS5595_REG_FAN_MIN(i));
 	}
 
 	/* Register sysfs hooks */
-	if ((err = sysfs_create_group(&new_client->dev.kobj, &sis5595_group)))
-		goto exit_detach;
+	if ((err = sysfs_create_group(&pdev->dev.kobj, &sis5595_group)))
+		goto exit_free;
 	if (data->maxins == 4) {
-		if ((err = device_create_file(&new_client->dev,
-					      &dev_attr_in4_input))
-		 || (err = device_create_file(&new_client->dev,
-					      &dev_attr_in4_min))
-		 || (err = device_create_file(&new_client->dev,
-					      &dev_attr_in4_max)))
+		if ((err = device_create_file(&pdev->dev,
+					&sensor_dev_attr_in4_input.dev_attr))
+		 || (err = device_create_file(&pdev->dev,
+					&sensor_dev_attr_in4_min.dev_attr))
+		 || (err = device_create_file(&pdev->dev,
+					&sensor_dev_attr_in4_max.dev_attr)))
 			goto exit_remove_files;
 	} else {
-		if ((err = device_create_file(&new_client->dev,
+		if ((err = device_create_file(&pdev->dev,
 					      &dev_attr_temp1_input))
-		 || (err = device_create_file(&new_client->dev,
+		 || (err = device_create_file(&pdev->dev,
 					      &dev_attr_temp1_max))
-		 || (err = device_create_file(&new_client->dev,
+		 || (err = device_create_file(&pdev->dev,
 					      &dev_attr_temp1_max_hyst)))
 			goto exit_remove_files;
 	}
 
-	data->class_dev = hwmon_device_register(&new_client->dev);
+	data->class_dev = hwmon_device_register(&pdev->dev);
 	if (IS_ERR(data->class_dev)) {
 		err = PTR_ERR(data->class_dev);
 		goto exit_remove_files;
@@ -638,32 +566,26 @@
 	return 0;
 
 exit_remove_files:
-	sysfs_remove_group(&new_client->dev.kobj, &sis5595_group);
-	sysfs_remove_group(&new_client->dev.kobj, &sis5595_group_opt);
-exit_detach:
-	i2c_detach_client(new_client);
+	sysfs_remove_group(&pdev->dev.kobj, &sis5595_group);
+	sysfs_remove_group(&pdev->dev.kobj, &sis5595_group_opt);
 exit_free:
 	kfree(data);
 exit_release:
-	release_region(address, SIS5595_EXTENT);
+	release_region(res->start, SIS5595_EXTENT);
 exit:
 	return err;
 }
 
-static int sis5595_detach_client(struct i2c_client *client)
+static int __devexit sis5595_remove(struct platform_device *pdev)
 {
-	struct sis5595_data *data = i2c_get_clientdata(client);
-	int err;
+	struct sis5595_data *data = platform_get_drvdata(pdev);
 
 	hwmon_device_unregister(data->class_dev);
-	sysfs_remove_group(&client->dev.kobj, &sis5595_group);
-	sysfs_remove_group(&client->dev.kobj, &sis5595_group_opt);
+	sysfs_remove_group(&pdev->dev.kobj, &sis5595_group);
+	sysfs_remove_group(&pdev->dev.kobj, &sis5595_group_opt);
 
-	if ((err = i2c_detach_client(client)))
-		return err;
-
-	release_region(client->addr, SIS5595_EXTENT);
-
+	release_region(data->addr, SIS5595_EXTENT);
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 
 	return 0;
@@ -671,41 +593,37 @@
 
 
 /* ISA access must be locked explicitly. */
-static int sis5595_read_value(struct i2c_client *client, u8 reg)
+static int sis5595_read_value(struct sis5595_data *data, u8 reg)
 {
 	int res;
 
-	struct sis5595_data *data = i2c_get_clientdata(client);
 	mutex_lock(&data->lock);
-	outb_p(reg, client->addr + SIS5595_ADDR_REG_OFFSET);
-	res = inb_p(client->addr + SIS5595_DATA_REG_OFFSET);
+	outb_p(reg, data->addr + SIS5595_ADDR_REG_OFFSET);
+	res = inb_p(data->addr + SIS5595_DATA_REG_OFFSET);
 	mutex_unlock(&data->lock);
 	return res;
 }
 
-static int sis5595_write_value(struct i2c_client *client, u8 reg, u8 value)
+static void sis5595_write_value(struct sis5595_data *data, u8 reg, u8 value)
 {
-	struct sis5595_data *data = i2c_get_clientdata(client);
 	mutex_lock(&data->lock);
-	outb_p(reg, client->addr + SIS5595_ADDR_REG_OFFSET);
-	outb_p(value, client->addr + SIS5595_DATA_REG_OFFSET);
+	outb_p(reg, data->addr + SIS5595_ADDR_REG_OFFSET);
+	outb_p(value, data->addr + SIS5595_DATA_REG_OFFSET);
 	mutex_unlock(&data->lock);
-	return 0;
 }
 
 /* Called when we have found a new SIS5595. */
-static void sis5595_init_client(struct i2c_client *client)
+static void __devinit sis5595_init_device(struct sis5595_data *data)
 {
-	u8 config = sis5595_read_value(client, SIS5595_REG_CONFIG);
+	u8 config = sis5595_read_value(data, SIS5595_REG_CONFIG);
 	if (!(config & 0x01))
-		sis5595_write_value(client, SIS5595_REG_CONFIG,
+		sis5595_write_value(data, SIS5595_REG_CONFIG,
 				(config & 0xf7) | 0x01);
 }
 
 static struct sis5595_data *sis5595_update_device(struct device *dev)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct sis5595_data *data = i2c_get_clientdata(client);
+	struct sis5595_data *data = dev_get_drvdata(dev);
 	int i;
 
 	mutex_lock(&data->update_lock);
@@ -715,35 +633,35 @@
 
 		for (i = 0; i <= data->maxins; i++) {
 			data->in[i] =
-			    sis5595_read_value(client, SIS5595_REG_IN(i));
+			    sis5595_read_value(data, SIS5595_REG_IN(i));
 			data->in_min[i] =
-			    sis5595_read_value(client,
+			    sis5595_read_value(data,
 					       SIS5595_REG_IN_MIN(i));
 			data->in_max[i] =
-			    sis5595_read_value(client,
+			    sis5595_read_value(data,
 					       SIS5595_REG_IN_MAX(i));
 		}
 		for (i = 0; i < 2; i++) {
 			data->fan[i] =
-			    sis5595_read_value(client, SIS5595_REG_FAN(i));
+			    sis5595_read_value(data, SIS5595_REG_FAN(i));
 			data->fan_min[i] =
-			    sis5595_read_value(client,
+			    sis5595_read_value(data,
 					       SIS5595_REG_FAN_MIN(i));
 		}
 		if (data->maxins == 3) {
 			data->temp =
-			    sis5595_read_value(client, SIS5595_REG_TEMP);
+			    sis5595_read_value(data, SIS5595_REG_TEMP);
 			data->temp_over =
-			    sis5595_read_value(client, SIS5595_REG_TEMP_OVER);
+			    sis5595_read_value(data, SIS5595_REG_TEMP_OVER);
 			data->temp_hyst =
-			    sis5595_read_value(client, SIS5595_REG_TEMP_HYST);
+			    sis5595_read_value(data, SIS5595_REG_TEMP_HYST);
 		}
-		i = sis5595_read_value(client, SIS5595_REG_FANDIV);
+		i = sis5595_read_value(data, SIS5595_REG_FANDIV);
 		data->fan_div[0] = (i >> 4) & 0x03;
 		data->fan_div[1] = i >> 6;
 		data->alarms =
-		    sis5595_read_value(client, SIS5595_REG_ALARM1) |
-		    (sis5595_read_value(client, SIS5595_REG_ALARM2) << 8);
+		    sis5595_read_value(data, SIS5595_REG_ALARM1) |
+		    (sis5595_read_value(data, SIS5595_REG_ALARM2) << 8);
 		data->last_updated = jiffies;
 		data->valid = 1;
 	}
@@ -774,10 +692,50 @@
 	PCI_DEVICE_ID_SI_5598,
 	0 };
 
+static int __devinit sis5595_device_add(unsigned short address)
+{
+	struct resource res = {
+		.start	= address,
+		.end	= address + SIS5595_EXTENT - 1,
+		.name	= "sis5595",
+		.flags	= IORESOURCE_IO,
+	};
+	int err;
+
+	pdev = platform_device_alloc("sis5595", address);
+	if (!pdev) {
+		err = -ENOMEM;
+		printk(KERN_ERR "sis5595: Device allocation failed\n");
+		goto exit;
+	}
+
+	err = platform_device_add_resources(pdev, &res, 1);
+	if (err) {
+		printk(KERN_ERR "sis5595: Device resource addition failed "
+		       "(%d)\n", err);
+		goto exit_device_put;
+	}
+
+	err = platform_device_add(pdev);
+	if (err) {
+		printk(KERN_ERR "sis5595: Device addition failed (%d)\n",
+		       err);
+		goto exit_device_put;
+	}
+
+	return 0;
+
+exit_device_put:
+	platform_device_put(pdev);
+exit:
+	return err;
+}
+
 static int __devinit sis5595_pci_probe(struct pci_dev *dev,
 				       const struct pci_device_id *id)
 {
-	u16 val;
+	u16 address;
+	u8 enable;
 	int *i;
 
 	for (i = blacklist; *i != 0; i++) {
@@ -790,27 +748,68 @@
 		}
 	}
 	
+	force_addr &= ~(SIS5595_EXTENT - 1);
+	if (force_addr) {
+		dev_warn(&dev->dev, "Forcing ISA address 0x%x\n", force_addr);
+		pci_write_config_word(dev, SIS5595_BASE_REG, force_addr);
+	}
+
 	if (PCIBIOS_SUCCESSFUL !=
-	    pci_read_config_word(dev, SIS5595_BASE_REG, &val))
+	    pci_read_config_word(dev, SIS5595_BASE_REG, &address)) {
+		dev_err(&dev->dev, "Failed to read ISA address\n");
 		return -ENODEV;
+	}
 	
-	address = val & ~(SIS5595_EXTENT - 1);
-	if (address == 0 && force_addr == 0) {
+	address &= ~(SIS5595_EXTENT - 1);
+	if (!address) {
 		dev_err(&dev->dev, "Base address not set - upgrade BIOS or use force_addr=0xaddr\n");
 		return -ENODEV;
 	}
+	if (force_addr && address != force_addr) {
+		/* doesn't work for some chips? */
+		dev_err(&dev->dev, "Failed to force ISA address\n");
+		return -ENODEV;
+	}
+
+	if (PCIBIOS_SUCCESSFUL !=
+	    pci_read_config_byte(dev, SIS5595_ENABLE_REG, &enable)) {
+		dev_err(&dev->dev, "Failed to read enable register\n");
+		return -ENODEV;
+	}
+	if (!(enable & 0x80)) {
+		if ((PCIBIOS_SUCCESSFUL !=
+		     pci_write_config_byte(dev, SIS5595_ENABLE_REG,
+					   enable | 0x80))
+		 || (PCIBIOS_SUCCESSFUL !=
+		     pci_read_config_byte(dev, SIS5595_ENABLE_REG, &enable))
+		 || (!(enable & 0x80))) {
+			/* doesn't work for some chips! */
+			dev_err(&dev->dev, "Failed to enable HWM device\n");
+			return -ENODEV;
+		}
+	}
+
+	if (platform_driver_register(&sis5595_driver)) {
+		dev_dbg(&dev->dev, "Failed to register sis5595 driver\n");
+		goto exit;
+	}
 
 	s_bridge = pci_dev_get(dev);
-	if (i2c_isa_add_driver(&sis5595_driver)) {
-		pci_dev_put(s_bridge);
-		s_bridge = NULL;
-	}
+	/* Sets global pdev as a side effect */
+	if (sis5595_device_add(address))
+		goto exit_unregister;
 
 	/* Always return failure here.  This is to allow other drivers to bind
 	 * to this pci device.  We don't really want to have control over the
 	 * pci device, we only wanted to read as few register values from it.
 	 */
 	return -ENODEV;
+
+exit_unregister:
+	pci_dev_put(dev);
+	platform_driver_unregister(&sis5595_driver);
+exit:
+	return -ENODEV;
 }
 
 static struct pci_driver sis5595_pci_driver = {
@@ -828,7 +827,8 @@
 {
 	pci_unregister_driver(&sis5595_pci_driver);
 	if (s_bridge != NULL) {
-		i2c_isa_del_driver(&sis5595_driver);
+		platform_device_unregister(pdev);
+		platform_driver_unregister(&sis5595_driver);
 		pci_dev_put(s_bridge);
 		s_bridge = NULL;
 	}
diff --git a/drivers/hwmon/smsc47b397.c b/drivers/hwmon/smsc47b397.c
index 943abbd..45266b3 100644
--- a/drivers/hwmon/smsc47b397.c
+++ b/drivers/hwmon/smsc47b397.c
@@ -174,6 +174,8 @@
    REG: count of 90kHz pulses / revolution */
 static int fan_from_reg(u16 reg)
 {
+	if (reg == 0 || reg == 0xffff)
+		return 0;
 	return 90000 * 60 / reg;
 }
 
@@ -333,7 +335,7 @@
 	superio_enter();
 	id = superio_inb(SUPERIO_REG_DEVID);
 
-	if ((id != 0x6f) && (id != 0x81)) {
+	if ((id != 0x6f) && (id != 0x81) && (id != 0x85)) {
 		superio_exit();
 		return -ENODEV;
 	}
@@ -346,7 +348,8 @@
 
 	printk(KERN_INFO DRVNAME ": found SMSC %s "
 		"(base address 0x%04x, revision %u)\n",
-		id == 0x81 ? "SCH5307-NS" : "LPC47B397-NC", *addr, rev);
+		id == 0x81 ? "SCH5307-NS" : id == 0x85 ? "SCH5317" :
+	       "LPC47B397-NC", *addr, rev);
 
 	superio_exit();
 	return 0;
diff --git a/drivers/hwmon/smsc47m1.c b/drivers/hwmon/smsc47m1.c
index 1e21c8c..1de2f2b 100644
--- a/drivers/hwmon/smsc47m1.c
+++ b/drivers/hwmon/smsc47m1.c
@@ -597,6 +597,7 @@
 error_remove_files:
 	sysfs_remove_group(&dev->kobj, &smsc47m1_group);
 error_free:
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 error_release:
 	release_region(res->start, SMSC_EXTENT);
@@ -608,12 +609,12 @@
 	struct smsc47m1_data *data = platform_get_drvdata(pdev);
 	struct resource *res;
 
-	platform_set_drvdata(pdev, NULL);
 	hwmon_device_unregister(data->class_dev);
 	sysfs_remove_group(&pdev->dev.kobj, &smsc47m1_group);
 
 	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
 	release_region(res->start, SMSC_EXTENT);
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 
 	return 0;
@@ -693,15 +694,12 @@
 		goto exit_device_put;
 	}
 
-	pdev->dev.platform_data = kmalloc(sizeof(struct smsc47m1_sio_data),
-					  GFP_KERNEL);
-	if (!pdev->dev.platform_data) {
-		err = -ENOMEM;
+	err = platform_device_add_data(pdev, sio_data,
+				       sizeof(struct smsc47m1_sio_data));
+	if (err) {
 		printk(KERN_ERR DRVNAME ": Platform data allocation failed\n");
 		goto exit_device_put;
 	}
-	memcpy(pdev->dev.platform_data, sio_data,
-	       sizeof(struct smsc47m1_sio_data));
 
 	err = platform_device_add(pdev);
 	if (err) {
diff --git a/drivers/hwmon/smsc47m192.c b/drivers/hwmon/smsc47m192.c
index a012f39..d3a3ba0 100644
--- a/drivers/hwmon/smsc47m192.c
+++ b/drivers/hwmon/smsc47m192.c
@@ -31,6 +31,7 @@
 #include <linux/hwmon-vid.h>
 #include <linux/err.h>
 #include <linux/sysfs.h>
+#include <linux/mutex.h>
 
 /* Addresses to scan */
 static unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END };
@@ -97,7 +98,7 @@
 struct smsc47m192_data {
 	struct i2c_client client;
 	struct class_device *class_dev;
-	struct semaphore update_lock;
+	struct mutex update_lock;
 	char valid;		/* !=0 if following fields are valid */
 	unsigned long last_updated;	/* In jiffies */
 
@@ -164,11 +165,11 @@
 	struct smsc47m192_data *data = i2c_get_clientdata(client);
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
-	down(&data->update_lock);
+	mutex_lock(&data->update_lock);
 	data->in_min[nr] = IN_TO_REG(val, nr);
 	i2c_smbus_write_byte_data(client, SMSC47M192_REG_IN_MIN(nr),
 							data->in_min[nr]);
-	up(&data->update_lock);
+	mutex_unlock(&data->update_lock);
 	return count;
 }
 
@@ -181,11 +182,11 @@
 	struct smsc47m192_data *data = i2c_get_clientdata(client);
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
-	down(&data->update_lock);
+	mutex_lock(&data->update_lock);
 	data->in_max[nr] = IN_TO_REG(val, nr);
 	i2c_smbus_write_byte_data(client, SMSC47M192_REG_IN_MAX(nr),
 							data->in_max[nr]);
-	up(&data->update_lock);
+	mutex_unlock(&data->update_lock);
 	return count;
 }
 
@@ -243,11 +244,11 @@
 	struct smsc47m192_data *data = i2c_get_clientdata(client);
 	long val = simple_strtol(buf, NULL, 10);
 
-	down(&data->update_lock);
+	mutex_lock(&data->update_lock);
 	data->temp_min[nr] = TEMP_TO_REG(val);
 	i2c_smbus_write_byte_data(client, SMSC47M192_REG_TEMP_MIN[nr],
 						data->temp_min[nr]);
-	up(&data->update_lock);
+	mutex_unlock(&data->update_lock);
 	return count;
 }
 
@@ -260,11 +261,11 @@
 	struct smsc47m192_data *data = i2c_get_clientdata(client);
 	long val = simple_strtol(buf, NULL, 10);
 
-	down(&data->update_lock);
+	mutex_lock(&data->update_lock);
 	data->temp_max[nr] = TEMP_TO_REG(val);
 	i2c_smbus_write_byte_data(client, SMSC47M192_REG_TEMP_MAX[nr],
 						data->temp_max[nr]);
-	up(&data->update_lock);
+	mutex_unlock(&data->update_lock);
 	return count;
 }
 
@@ -287,7 +288,7 @@
 	u8 sfr = i2c_smbus_read_byte_data(client, SMSC47M192_REG_SFR);
 	long val = simple_strtol(buf, NULL, 10);
 
-	down(&data->update_lock);
+	mutex_lock(&data->update_lock);
 	data->temp_offset[nr] = TEMP_TO_REG(val);
 	if (nr>1)
 		i2c_smbus_write_byte_data(client,
@@ -303,7 +304,7 @@
 	} else if ((sfr & 0x10) == (nr==0 ? 0x10 : 0))
 		i2c_smbus_write_byte_data(client,
 					SMSC47M192_REG_TEMP_OFFSET(nr), 0);
-	up(&data->update_lock);
+	mutex_unlock(&data->update_lock);
 	return count;
 }
 
@@ -360,8 +361,8 @@
 static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 0x0010);
 static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 0x0020);
 static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 0x0040);
-static SENSOR_DEVICE_ATTR(temp2_input_fault, S_IRUGO, show_alarm, NULL, 0x4000);
-static SENSOR_DEVICE_ATTR(temp3_input_fault, S_IRUGO, show_alarm, NULL, 0x8000);
+static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 0x4000);
+static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_alarm, NULL, 0x8000);
 static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0x0001);
 static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 0x0002);
 static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 0x0004);
@@ -411,13 +412,13 @@
 	&sensor_dev_attr_temp2_min.dev_attr.attr,
 	&sensor_dev_attr_temp2_offset.dev_attr.attr,
 	&sensor_dev_attr_temp2_alarm.dev_attr.attr,
-	&sensor_dev_attr_temp2_input_fault.dev_attr.attr,
+	&sensor_dev_attr_temp2_fault.dev_attr.attr,
 	&sensor_dev_attr_temp3_input.dev_attr.attr,
 	&sensor_dev_attr_temp3_max.dev_attr.attr,
 	&sensor_dev_attr_temp3_min.dev_attr.attr,
 	&sensor_dev_attr_temp3_offset.dev_attr.attr,
 	&sensor_dev_attr_temp3_alarm.dev_attr.attr,
-	&sensor_dev_attr_temp3_input_fault.dev_attr.attr,
+	&sensor_dev_attr_temp3_fault.dev_attr.attr,
 
 	&dev_attr_cpu0_vid.attr,
 	&dev_attr_vrm.attr,
@@ -531,7 +532,7 @@
 	/* Fill in the remaining client fields and put into the global list */
 	strlcpy(client->name, "smsc47m192", I2C_NAME_SIZE);
 	data->vrm = vid_which_vrm();
-	init_MUTEX(&data->update_lock);
+	mutex_init(&data->update_lock);
 
 	/* Tell the I2C layer a new client has arrived */
 	if ((err = i2c_attach_client(client)))
@@ -594,7 +595,7 @@
 	struct smsc47m192_data *data = i2c_get_clientdata(client);
 	int i, config;
 
-	down(&data->update_lock);
+	mutex_lock(&data->update_lock);
 
 	if (time_after(jiffies, data->last_updated + HZ + HZ / 2)
 	 || !data->valid) {
@@ -645,7 +646,7 @@
 		data->valid = 1;
 	}
 
-	up(&data->update_lock);
+	mutex_unlock(&data->update_lock);
 
 	return data;
 }
diff --git a/drivers/hwmon/via686a.c b/drivers/hwmon/via686a.c
index 9a440c8..24a6851 100644
--- a/drivers/hwmon/via686a.c
+++ b/drivers/hwmon/via686a.c
@@ -34,9 +34,9 @@
 #include <linux/slab.h>
 #include <linux/pci.h>
 #include <linux/jiffies.h>
-#include <linux/i2c.h>
-#include <linux/i2c-isa.h>
+#include <linux/platform_device.h>
 #include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
 #include <linux/err.h>
 #include <linux/init.h>
 #include <linux/mutex.h>
@@ -51,10 +51,7 @@
 MODULE_PARM_DESC(force_addr,
 		 "Initialize the base address of the sensors");
 
-/* Device address
-   Note that we can't determine the ISA address until we have initialized
-   our module */
-static unsigned short address;
+static struct platform_device *pdev;
 
 /*
    The Via 686a southbridge has a LM78-like chip integrated on the same IC.
@@ -295,7 +292,8 @@
 /* For each registered chip, we need to keep some data in memory.
    The structure is dynamically allocated. */
 struct via686a_data {
-	struct i2c_client client;
+	unsigned short addr;
+	const char *name;
 	struct class_device *class_dev;
 	struct mutex update_lock;
 	char valid;		/* !=0 if following fields are valid */
@@ -315,98 +313,85 @@
 
 static struct pci_dev *s_bridge;	/* pointer to the (only) via686a */
 
-static int via686a_detect(struct i2c_adapter *adapter);
-static int via686a_detach_client(struct i2c_client *client);
+static int via686a_probe(struct platform_device *pdev);
+static int via686a_remove(struct platform_device *pdev);
 
-static inline int via686a_read_value(struct i2c_client *client, u8 reg)
+static inline int via686a_read_value(struct via686a_data *data, u8 reg)
 {
-	return (inb_p(client->addr + reg));
+	return inb_p(data->addr + reg);
 }
 
-static inline void via686a_write_value(struct i2c_client *client, u8 reg,
+static inline void via686a_write_value(struct via686a_data *data, u8 reg,
 				       u8 value)
 {
-	outb_p(value, client->addr + reg);
+	outb_p(value, data->addr + reg);
 }
 
 static struct via686a_data *via686a_update_device(struct device *dev);
-static void via686a_init_client(struct i2c_client *client);
+static void via686a_init_device(struct via686a_data *data);
 
 /* following are the sysfs callback functions */
 
 /* 7 voltage sensors */
-static ssize_t show_in(struct device *dev, char *buf, int nr) {
+static ssize_t show_in(struct device *dev, struct device_attribute *da,
+		char *buf) {
 	struct via686a_data *data = via686a_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%ld\n", IN_FROM_REG(data->in[nr], nr));
 }
 
-static ssize_t show_in_min(struct device *dev, char *buf, int nr) {
+static ssize_t show_in_min(struct device *dev, struct device_attribute *da,
+		char *buf) {
 	struct via686a_data *data = via686a_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%ld\n", IN_FROM_REG(data->in_min[nr], nr));
 }
 
-static ssize_t show_in_max(struct device *dev, char *buf, int nr) {
+static ssize_t show_in_max(struct device *dev, struct device_attribute *da,
+		char *buf) {
 	struct via686a_data *data = via686a_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%ld\n", IN_FROM_REG(data->in_max[nr], nr));
 }
 
-static ssize_t set_in_min(struct device *dev, const char *buf,
-		size_t count, int nr) {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct via686a_data *data = i2c_get_clientdata(client);
+static ssize_t set_in_min(struct device *dev, struct device_attribute *da,
+		const char *buf, size_t count) {
+	struct via686a_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->in_min[nr] = IN_TO_REG(val, nr);
-	via686a_write_value(client, VIA686A_REG_IN_MIN(nr),
+	via686a_write_value(data, VIA686A_REG_IN_MIN(nr),
 			data->in_min[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
-static ssize_t set_in_max(struct device *dev, const char *buf,
-		size_t count, int nr) {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct via686a_data *data = i2c_get_clientdata(client);
+static ssize_t set_in_max(struct device *dev, struct device_attribute *da,
+		const char *buf, size_t count) {
+	struct via686a_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->in_max[nr] = IN_TO_REG(val, nr);
-	via686a_write_value(client, VIA686A_REG_IN_MAX(nr),
+	via686a_write_value(data, VIA686A_REG_IN_MAX(nr),
 			data->in_max[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
 #define show_in_offset(offset)					\
-static ssize_t 							\
-	show_in##offset (struct device *dev, struct device_attribute *attr, char *buf)		\
-{								\
-	return show_in(dev, buf, offset);			\
-}								\
-static ssize_t 							\
-	show_in##offset##_min (struct device *dev, struct device_attribute *attr, char *buf)	\
-{								\
-	return show_in_min(dev, buf, offset);		\
-}								\
-static ssize_t 							\
-	show_in##offset##_max (struct device *dev, struct device_attribute *attr, char *buf)	\
-{								\
-	return show_in_max(dev, buf, offset);		\
-}								\
-static ssize_t set_in##offset##_min (struct device *dev, struct device_attribute *attr, 	\
-		const char *buf, size_t count) 			\
-{								\
-	return set_in_min(dev, buf, count, offset);		\
-}								\
-static ssize_t set_in##offset##_max (struct device *dev, struct device_attribute *attr,	\
-			const char *buf, size_t count)		\
-{								\
-	return set_in_max(dev, buf, count, offset);		\
-}								\
-static DEVICE_ATTR(in##offset##_input, S_IRUGO, show_in##offset, NULL);\
-static DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR, 	\
-		show_in##offset##_min, set_in##offset##_min);	\
-static DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR, 	\
-		show_in##offset##_max, set_in##offset##_max);
+static SENSOR_DEVICE_ATTR(in##offset##_input, S_IRUGO,		\
+		show_in, NULL, offset);				\
+static SENSOR_DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR,	\
+		show_in_min, set_in_min, offset);		\
+static SENSOR_DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR,	\
+		show_in_max, set_in_max, offset);
 
 show_in_offset(0);
 show_in_offset(1);
@@ -415,150 +400,128 @@
 show_in_offset(4);
 
 /* 3 temperatures */
-static ssize_t show_temp(struct device *dev, char *buf, int nr) {
+static ssize_t show_temp(struct device *dev, struct device_attribute *da,
+		char *buf) {
 	struct via686a_data *data = via686a_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%ld\n", TEMP_FROM_REG10(data->temp[nr]));
 }
-static ssize_t show_temp_over(struct device *dev, char *buf, int nr) {
+static ssize_t show_temp_over(struct device *dev, struct device_attribute *da,
+		char *buf) {
 	struct via686a_data *data = via686a_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%ld\n", TEMP_FROM_REG(data->temp_over[nr]));
 }
-static ssize_t show_temp_hyst(struct device *dev, char *buf, int nr) {
+static ssize_t show_temp_hyst(struct device *dev, struct device_attribute *da,
+		char *buf) {
 	struct via686a_data *data = via686a_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%ld\n", TEMP_FROM_REG(data->temp_hyst[nr]));
 }
-static ssize_t set_temp_over(struct device *dev, const char *buf,
-		size_t count, int nr) {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct via686a_data *data = i2c_get_clientdata(client);
+static ssize_t set_temp_over(struct device *dev, struct device_attribute *da,
+		const char *buf, size_t count) {
+	struct via686a_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	int val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->temp_over[nr] = TEMP_TO_REG(val);
-	via686a_write_value(client, VIA686A_REG_TEMP_OVER[nr],
+	via686a_write_value(data, VIA686A_REG_TEMP_OVER[nr],
 			    data->temp_over[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
-static ssize_t set_temp_hyst(struct device *dev, const char *buf,
-		size_t count, int nr) {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct via686a_data *data = i2c_get_clientdata(client);
+static ssize_t set_temp_hyst(struct device *dev, struct device_attribute *da,
+		const char *buf, size_t count) {
+	struct via686a_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	int val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->temp_hyst[nr] = TEMP_TO_REG(val);
-	via686a_write_value(client, VIA686A_REG_TEMP_HYST[nr],
+	via686a_write_value(data, VIA686A_REG_TEMP_HYST[nr],
 			    data->temp_hyst[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
 #define show_temp_offset(offset)					\
-static ssize_t show_temp_##offset (struct device *dev, struct device_attribute *attr, char *buf)	\
-{									\
-	return show_temp(dev, buf, offset - 1);				\
-}									\
-static ssize_t								\
-show_temp_##offset##_over (struct device *dev, struct device_attribute *attr, char *buf)		\
-{									\
-	return show_temp_over(dev, buf, offset - 1);			\
-}									\
-static ssize_t								\
-show_temp_##offset##_hyst (struct device *dev, struct device_attribute *attr, char *buf)		\
-{									\
-	return show_temp_hyst(dev, buf, offset - 1);			\
-}									\
-static ssize_t set_temp_##offset##_over (struct device *dev, struct device_attribute *attr, 		\
-		const char *buf, size_t count) 				\
-{									\
-	return set_temp_over(dev, buf, count, offset - 1);		\
-}									\
-static ssize_t set_temp_##offset##_hyst (struct device *dev, struct device_attribute *attr, 		\
-		const char *buf, size_t count) 				\
-{									\
-	return set_temp_hyst(dev, buf, count, offset - 1);		\
-}									\
-static DEVICE_ATTR(temp##offset##_input, S_IRUGO, show_temp_##offset, NULL);\
-static DEVICE_ATTR(temp##offset##_max, S_IRUGO | S_IWUSR, 		\
-		show_temp_##offset##_over, set_temp_##offset##_over);	\
-static DEVICE_ATTR(temp##offset##_max_hyst, S_IRUGO | S_IWUSR, 		\
-		show_temp_##offset##_hyst, set_temp_##offset##_hyst);
+static SENSOR_DEVICE_ATTR(temp##offset##_input, S_IRUGO,		\
+		show_temp, NULL, offset - 1);				\
+static SENSOR_DEVICE_ATTR(temp##offset##_max, S_IRUGO | S_IWUSR,	\
+		show_temp_over, set_temp_over, offset - 1);		\
+static SENSOR_DEVICE_ATTR(temp##offset##_max_hyst, S_IRUGO | S_IWUSR,	\
+		show_temp_hyst, set_temp_hyst, offset - 1);
 
 show_temp_offset(1);
 show_temp_offset(2);
 show_temp_offset(3);
 
 /* 2 Fans */
-static ssize_t show_fan(struct device *dev, char *buf, int nr) {
+static ssize_t show_fan(struct device *dev, struct device_attribute *da,
+		char *buf) {
 	struct via686a_data *data = via686a_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan[nr],
 				DIV_FROM_REG(data->fan_div[nr])) );
 }
-static ssize_t show_fan_min(struct device *dev, char *buf, int nr) {
+static ssize_t show_fan_min(struct device *dev, struct device_attribute *da,
+		char *buf) {
 	struct via686a_data *data = via686a_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%d\n",
 		FAN_FROM_REG(data->fan_min[nr], DIV_FROM_REG(data->fan_div[nr])) );
 }
-static ssize_t show_fan_div(struct device *dev, char *buf, int nr) {
+static ssize_t show_fan_div(struct device *dev, struct device_attribute *da,
+		char *buf) {
 	struct via686a_data *data = via686a_update_device(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	return sprintf(buf, "%d\n", DIV_FROM_REG(data->fan_div[nr]) );
 }
-static ssize_t set_fan_min(struct device *dev, const char *buf,
-		size_t count, int nr) {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct via686a_data *data = i2c_get_clientdata(client);
+static ssize_t set_fan_min(struct device *dev, struct device_attribute *da,
+		const char *buf, size_t count) {
+	struct via686a_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	int val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->fan_min[nr] = FAN_TO_REG(val, DIV_FROM_REG(data->fan_div[nr]));
-	via686a_write_value(client, VIA686A_REG_FAN_MIN(nr+1), data->fan_min[nr]);
+	via686a_write_value(data, VIA686A_REG_FAN_MIN(nr+1), data->fan_min[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
-static ssize_t set_fan_div(struct device *dev, const char *buf,
-		size_t count, int nr) {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct via686a_data *data = i2c_get_clientdata(client);
+static ssize_t set_fan_div(struct device *dev, struct device_attribute *da,
+		const char *buf, size_t count) {
+	struct via686a_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	int nr = attr->index;
 	int val = simple_strtol(buf, NULL, 10);
 	int old;
 
 	mutex_lock(&data->update_lock);
-	old = via686a_read_value(client, VIA686A_REG_FANDIV);
+	old = via686a_read_value(data, VIA686A_REG_FANDIV);
 	data->fan_div[nr] = DIV_TO_REG(val);
 	old = (old & 0x0f) | (data->fan_div[1] << 6) | (data->fan_div[0] << 4);
-	via686a_write_value(client, VIA686A_REG_FANDIV, old);
+	via686a_write_value(data, VIA686A_REG_FANDIV, old);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
 
 #define show_fan_offset(offset)						\
-static ssize_t show_fan_##offset (struct device *dev, struct device_attribute *attr, char *buf)	\
-{									\
-	return show_fan(dev, buf, offset - 1);				\
-}									\
-static ssize_t show_fan_##offset##_min (struct device *dev, struct device_attribute *attr, char *buf)	\
-{									\
-	return show_fan_min(dev, buf, offset - 1);			\
-}									\
-static ssize_t show_fan_##offset##_div (struct device *dev, struct device_attribute *attr, char *buf)	\
-{									\
-	return show_fan_div(dev, buf, offset - 1);			\
-}									\
-static ssize_t set_fan_##offset##_min (struct device *dev, struct device_attribute *attr, 		\
-	const char *buf, size_t count) 					\
-{									\
-	return set_fan_min(dev, buf, count, offset - 1);		\
-}									\
-static ssize_t set_fan_##offset##_div (struct device *dev, struct device_attribute *attr, 		\
-		const char *buf, size_t count) 				\
-{									\
-	return set_fan_div(dev, buf, count, offset - 1);		\
-}									\
-static DEVICE_ATTR(fan##offset##_input, S_IRUGO, show_fan_##offset, NULL);\
-static DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR, 		\
-		show_fan_##offset##_min, set_fan_##offset##_min);	\
-static DEVICE_ATTR(fan##offset##_div, S_IRUGO | S_IWUSR, 		\
-		show_fan_##offset##_div, set_fan_##offset##_div);
+static SENSOR_DEVICE_ATTR(fan##offset##_input, S_IRUGO,			\
+		show_fan, NULL, offset - 1);				\
+static SENSOR_DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR,		\
+		show_fan_min, set_fan_min, offset - 1);			\
+static SENSOR_DEVICE_ATTR(fan##offset##_div, S_IRUGO | S_IWUSR,		\
+		show_fan_div, set_fan_div, offset - 1);
 
 show_fan_offset(1);
 show_fan_offset(2);
@@ -570,41 +533,50 @@
 }
 static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
 
+static ssize_t show_name(struct device *dev, struct device_attribute
+			 *devattr, char *buf)
+{
+	struct via686a_data *data = dev_get_drvdata(dev);
+	return sprintf(buf, "%s\n", data->name);
+}
+static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
+
 static struct attribute *via686a_attributes[] = {
-	&dev_attr_in0_input.attr,
-	&dev_attr_in1_input.attr,
-	&dev_attr_in2_input.attr,
-	&dev_attr_in3_input.attr,
-	&dev_attr_in4_input.attr,
-	&dev_attr_in0_min.attr,
-	&dev_attr_in1_min.attr,
-	&dev_attr_in2_min.attr,
-	&dev_attr_in3_min.attr,
-	&dev_attr_in4_min.attr,
-	&dev_attr_in0_max.attr,
-	&dev_attr_in1_max.attr,
-	&dev_attr_in2_max.attr,
-	&dev_attr_in3_max.attr,
-	&dev_attr_in4_max.attr,
+	&sensor_dev_attr_in0_input.dev_attr.attr,
+	&sensor_dev_attr_in1_input.dev_attr.attr,
+	&sensor_dev_attr_in2_input.dev_attr.attr,
+	&sensor_dev_attr_in3_input.dev_attr.attr,
+	&sensor_dev_attr_in4_input.dev_attr.attr,
+	&sensor_dev_attr_in0_min.dev_attr.attr,
+	&sensor_dev_attr_in1_min.dev_attr.attr,
+	&sensor_dev_attr_in2_min.dev_attr.attr,
+	&sensor_dev_attr_in3_min.dev_attr.attr,
+	&sensor_dev_attr_in4_min.dev_attr.attr,
+	&sensor_dev_attr_in0_max.dev_attr.attr,
+	&sensor_dev_attr_in1_max.dev_attr.attr,
+	&sensor_dev_attr_in2_max.dev_attr.attr,
+	&sensor_dev_attr_in3_max.dev_attr.attr,
+	&sensor_dev_attr_in4_max.dev_attr.attr,
 
-	&dev_attr_temp1_input.attr,
-	&dev_attr_temp2_input.attr,
-	&dev_attr_temp3_input.attr,
-	&dev_attr_temp1_max.attr,
-	&dev_attr_temp2_max.attr,
-	&dev_attr_temp3_max.attr,
-	&dev_attr_temp1_max_hyst.attr,
-	&dev_attr_temp2_max_hyst.attr,
-	&dev_attr_temp3_max_hyst.attr,
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	&sensor_dev_attr_temp2_input.dev_attr.attr,
+	&sensor_dev_attr_temp3_input.dev_attr.attr,
+	&sensor_dev_attr_temp1_max.dev_attr.attr,
+	&sensor_dev_attr_temp2_max.dev_attr.attr,
+	&sensor_dev_attr_temp3_max.dev_attr.attr,
+	&sensor_dev_attr_temp1_max_hyst.dev_attr.attr,
+	&sensor_dev_attr_temp2_max_hyst.dev_attr.attr,
+	&sensor_dev_attr_temp3_max_hyst.dev_attr.attr,
 
-	&dev_attr_fan1_input.attr,
-	&dev_attr_fan2_input.attr,
-	&dev_attr_fan1_min.attr,
-	&dev_attr_fan2_min.attr,
-	&dev_attr_fan1_div.attr,
-	&dev_attr_fan2_div.attr,
+	&sensor_dev_attr_fan1_input.dev_attr.attr,
+	&sensor_dev_attr_fan2_input.dev_attr.attr,
+	&sensor_dev_attr_fan1_min.dev_attr.attr,
+	&sensor_dev_attr_fan2_min.dev_attr.attr,
+	&sensor_dev_attr_fan1_div.dev_attr.attr,
+	&sensor_dev_attr_fan2_div.dev_attr.attr,
 
 	&dev_attr_alarms.attr,
+	&dev_attr_name.attr,
 	NULL
 };
 
@@ -612,58 +584,29 @@
 	.attrs = via686a_attributes,
 };
 
-/* The driver. I choose to use type i2c_driver, as at is identical to both
-   smbus_driver and isa_driver, and clients could be of either kind */
-static struct i2c_driver via686a_driver = {
+static struct platform_driver via686a_driver = {
 	.driver = {
 		.owner	= THIS_MODULE,
 		.name	= "via686a",
 	},
-	.attach_adapter	= via686a_detect,
-	.detach_client	= via686a_detach_client,
+	.probe		= via686a_probe,
+	.remove		= __devexit_p(via686a_remove),
 };
 
 
 /* This is called when the module is loaded */
-static int via686a_detect(struct i2c_adapter *adapter)
+static int __devinit via686a_probe(struct platform_device *pdev)
 {
-	struct i2c_client *new_client;
 	struct via686a_data *data;
-	int err = 0;
-	const char client_name[] = "via686a";
-	u16 val;
-
-	/* 8231 requires multiple of 256, we enforce that on 686 as well */
-	if (force_addr) {
-		address = force_addr & 0xFF00;
-		dev_warn(&adapter->dev, "forcing ISA address 0x%04X\n",
-			 address);
-		if (PCIBIOS_SUCCESSFUL !=
-		    pci_write_config_word(s_bridge, VIA686A_BASE_REG, address))
-			return -ENODEV;
-	}
-	if (PCIBIOS_SUCCESSFUL !=
-	    pci_read_config_word(s_bridge, VIA686A_ENABLE_REG, &val))
-		return -ENODEV;
-	if (!(val & 0x0001)) {
-		if (force_addr) {
-			dev_info(&adapter->dev, "enabling sensors\n");
-			if (PCIBIOS_SUCCESSFUL !=
-			    pci_write_config_word(s_bridge, VIA686A_ENABLE_REG,
-						  val | 0x0001))
-				return -ENODEV;
-		} else {
-			dev_warn(&adapter->dev, "sensors disabled - enable "
-				 "with force_addr=0x%x\n", address);
-			return -ENODEV;
-		}
-	}
+	struct resource *res;
+	int err;
 
 	/* Reserve the ISA region */
-	if (!request_region(address, VIA686A_EXTENT,
+	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+	if (!request_region(res->start, VIA686A_EXTENT,
 			    via686a_driver.driver.name)) {
-		dev_err(&adapter->dev, "region 0x%x already in use!\n",
-			address);
+		dev_err(&pdev->dev, "Region 0x%lx-0x%lx already in use!\n",
+			(unsigned long)res->start, (unsigned long)res->end);
 		return -ENODEV;
 	}
 
@@ -672,30 +615,19 @@
 		goto exit_release;
 	}
 
-	new_client = &data->client;
-	i2c_set_clientdata(new_client, data);
-	new_client->addr = address;
-	new_client->adapter = adapter;
-	new_client->driver = &via686a_driver;
-	new_client->flags = 0;
-
-	/* Fill in the remaining client fields and put into the global list */
-	strlcpy(new_client->name, client_name, I2C_NAME_SIZE);
-
-	data->valid = 0;
+	platform_set_drvdata(pdev, data);
+	data->addr = res->start;
+	data->name = "via686a";
 	mutex_init(&data->update_lock);
-	/* Tell the I2C layer a new client has arrived */
-	if ((err = i2c_attach_client(new_client)))
-		goto exit_free;
 
 	/* Initialize the VIA686A chip */
-	via686a_init_client(new_client);
+	via686a_init_device(data);
 
 	/* Register sysfs hooks */
-	if ((err = sysfs_create_group(&new_client->dev.kobj, &via686a_group)))
-		goto exit_detach;
+	if ((err = sysfs_create_group(&pdev->dev.kobj, &via686a_group)))
+		goto exit_free;
 
-	data->class_dev = hwmon_device_register(&new_client->dev);
+	data->class_dev = hwmon_device_register(&pdev->dev);
 	if (IS_ERR(data->class_dev)) {
 		err = PTR_ERR(data->class_dev);
 		goto exit_remove_files;
@@ -704,51 +636,46 @@
 	return 0;
 
 exit_remove_files:
-	sysfs_remove_group(&new_client->dev.kobj, &via686a_group);
-exit_detach:
-	i2c_detach_client(new_client);
+	sysfs_remove_group(&pdev->dev.kobj, &via686a_group);
 exit_free:
 	kfree(data);
 exit_release:
-	release_region(address, VIA686A_EXTENT);
+	release_region(res->start, VIA686A_EXTENT);
 	return err;
 }
 
-static int via686a_detach_client(struct i2c_client *client)
+static int __devexit via686a_remove(struct platform_device *pdev)
 {
-	struct via686a_data *data = i2c_get_clientdata(client);
-	int err;
+	struct via686a_data *data = platform_get_drvdata(pdev);
 
 	hwmon_device_unregister(data->class_dev);
-	sysfs_remove_group(&client->dev.kobj, &via686a_group);
+	sysfs_remove_group(&pdev->dev.kobj, &via686a_group);
 
-	if ((err = i2c_detach_client(client)))
-		return err;
-
-	release_region(client->addr, VIA686A_EXTENT);
+	release_region(data->addr, VIA686A_EXTENT);
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 
 	return 0;
 }
 
-static void via686a_init_client(struct i2c_client *client)
+static void __devinit via686a_init_device(struct via686a_data *data)
 {
 	u8 reg;
 
 	/* Start monitoring */
-	reg = via686a_read_value(client, VIA686A_REG_CONFIG);
-	via686a_write_value(client, VIA686A_REG_CONFIG, (reg|0x01)&0x7F);
+	reg = via686a_read_value(data, VIA686A_REG_CONFIG);
+	via686a_write_value(data, VIA686A_REG_CONFIG, (reg | 0x01) & 0x7F);
 
 	/* Configure temp interrupt mode for continuous-interrupt operation */
-	via686a_write_value(client, VIA686A_REG_TEMP_MODE,
-			    via686a_read_value(client, VIA686A_REG_TEMP_MODE) &
-			    !(VIA686A_TEMP_MODE_MASK | VIA686A_TEMP_MODE_CONTINUOUS));
+	reg = via686a_read_value(data, VIA686A_REG_TEMP_MODE);
+	via686a_write_value(data, VIA686A_REG_TEMP_MODE,
+			    (reg & ~VIA686A_TEMP_MODE_MASK)
+			    | VIA686A_TEMP_MODE_CONTINUOUS);
 }
 
 static struct via686a_data *via686a_update_device(struct device *dev)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct via686a_data *data = i2c_get_clientdata(client);
+	struct via686a_data *data = dev_get_drvdata(dev);
 	int i;
 
 	mutex_lock(&data->update_lock);
@@ -757,27 +684,27 @@
 	    || !data->valid) {
 		for (i = 0; i <= 4; i++) {
 			data->in[i] =
-			    via686a_read_value(client, VIA686A_REG_IN(i));
-			data->in_min[i] = via686a_read_value(client,
+			    via686a_read_value(data, VIA686A_REG_IN(i));
+			data->in_min[i] = via686a_read_value(data,
 							     VIA686A_REG_IN_MIN
 							     (i));
 			data->in_max[i] =
-			    via686a_read_value(client, VIA686A_REG_IN_MAX(i));
+			    via686a_read_value(data, VIA686A_REG_IN_MAX(i));
 		}
 		for (i = 1; i <= 2; i++) {
 			data->fan[i - 1] =
-			    via686a_read_value(client, VIA686A_REG_FAN(i));
-			data->fan_min[i - 1] = via686a_read_value(client,
+			    via686a_read_value(data, VIA686A_REG_FAN(i));
+			data->fan_min[i - 1] = via686a_read_value(data,
 						     VIA686A_REG_FAN_MIN(i));
 		}
 		for (i = 0; i <= 2; i++) {
-			data->temp[i] = via686a_read_value(client,
+			data->temp[i] = via686a_read_value(data,
 						 VIA686A_REG_TEMP[i]) << 2;
 			data->temp_over[i] =
-			    via686a_read_value(client,
+			    via686a_read_value(data,
 					       VIA686A_REG_TEMP_OVER[i]);
 			data->temp_hyst[i] =
-			    via686a_read_value(client,
+			    via686a_read_value(data,
 					       VIA686A_REG_TEMP_HYST[i]);
 		}
 		/* add in lower 2 bits
@@ -785,23 +712,23 @@
 		   temp2 uses bits 5-4 of VIA686A_REG_TEMP_LOW23
 		   temp3 uses bits 7-6 of VIA686A_REG_TEMP_LOW23
 		 */
-		data->temp[0] |= (via686a_read_value(client,
+		data->temp[0] |= (via686a_read_value(data,
 						     VIA686A_REG_TEMP_LOW1)
 				  & 0xc0) >> 6;
 		data->temp[1] |=
-		    (via686a_read_value(client, VIA686A_REG_TEMP_LOW23) &
+		    (via686a_read_value(data, VIA686A_REG_TEMP_LOW23) &
 		     0x30) >> 4;
 		data->temp[2] |=
-		    (via686a_read_value(client, VIA686A_REG_TEMP_LOW23) &
+		    (via686a_read_value(data, VIA686A_REG_TEMP_LOW23) &
 		     0xc0) >> 6;
 
-		i = via686a_read_value(client, VIA686A_REG_FANDIV);
+		i = via686a_read_value(data, VIA686A_REG_FANDIV);
 		data->fan_div[0] = (i >> 4) & 0x03;
 		data->fan_div[1] = i >> 6;
 		data->alarms =
-		    via686a_read_value(client,
+		    via686a_read_value(data,
 				       VIA686A_REG_ALARM1) |
-		    (via686a_read_value(client, VIA686A_REG_ALARM2) << 8);
+		    (via686a_read_value(data, VIA686A_REG_ALARM2) << 8);
 		data->last_updated = jiffies;
 		data->valid = 1;
 	}
@@ -818,32 +745,102 @@
 
 MODULE_DEVICE_TABLE(pci, via686a_pci_ids);
 
+static int __devinit via686a_device_add(unsigned short address)
+{
+	struct resource res = {
+		.start	= address,
+		.end	= address + VIA686A_EXTENT - 1,
+		.name	= "via686a",
+		.flags	= IORESOURCE_IO,
+	};
+	int err;
+
+	pdev = platform_device_alloc("via686a", address);
+	if (!pdev) {
+		err = -ENOMEM;
+		printk(KERN_ERR "via686a: Device allocation failed\n");
+		goto exit;
+	}
+
+	err = platform_device_add_resources(pdev, &res, 1);
+	if (err) {
+		printk(KERN_ERR "via686a: Device resource addition failed "
+		       "(%d)\n", err);
+		goto exit_device_put;
+	}
+
+	err = platform_device_add(pdev);
+	if (err) {
+		printk(KERN_ERR "via686a: Device addition failed (%d)\n",
+		       err);
+		goto exit_device_put;
+	}
+
+	return 0;
+
+exit_device_put:
+	platform_device_put(pdev);
+exit:
+	return err;
+}
+
 static int __devinit via686a_pci_probe(struct pci_dev *dev,
 				       const struct pci_device_id *id)
 {
-	u16 val;
+	u16 address, val;
 
+	if (force_addr) {
+		address = force_addr & ~(VIA686A_EXTENT - 1);
+		dev_warn(&dev->dev, "Forcing ISA address 0x%x\n", address);
+		if (PCIBIOS_SUCCESSFUL !=
+		    pci_write_config_word(dev, VIA686A_BASE_REG, address | 1))
+			return -ENODEV;
+	}
 	if (PCIBIOS_SUCCESSFUL !=
 	    pci_read_config_word(dev, VIA686A_BASE_REG, &val))
 		return -ENODEV;
 
 	address = val & ~(VIA686A_EXTENT - 1);
-	if (address == 0 && force_addr == 0) {
+	if (address == 0) {
 		dev_err(&dev->dev, "base address not set - upgrade BIOS "
 			"or use force_addr=0xaddr\n");
 		return -ENODEV;
 	}
 
-	s_bridge = pci_dev_get(dev);
-	if (i2c_isa_add_driver(&via686a_driver)) {
-		pci_dev_put(s_bridge);
-		s_bridge = NULL;
+	if (PCIBIOS_SUCCESSFUL !=
+	    pci_read_config_word(dev, VIA686A_ENABLE_REG, &val))
+		return -ENODEV;
+	if (!(val & 0x0001)) {
+		if (!force_addr) {
+			dev_warn(&dev->dev, "Sensors disabled, enable "
+				 "with force_addr=0x%x\n", address);
+			return -ENODEV;
+		}
+
+		dev_warn(&dev->dev, "Enabling sensors\n");
+		if (PCIBIOS_SUCCESSFUL !=
+		    pci_write_config_word(dev, VIA686A_ENABLE_REG,
+					  val | 0x0001))
+			return -ENODEV;
 	}
 
+	if (platform_driver_register(&via686a_driver))
+		goto exit;
+
+	/* Sets global pdev as a side effect */
+	if (via686a_device_add(address))
+		goto exit_unregister;
+
 	/* Always return failure here.  This is to allow other drivers to bind
 	 * to this pci device.  We don't really want to have control over the
 	 * pci device, we only wanted to read as few register values from it.
 	 */
+	s_bridge = pci_dev_get(dev);
+	return -ENODEV;
+
+exit_unregister:
+	platform_driver_unregister(&via686a_driver);
+exit:
 	return -ENODEV;
 }
 
@@ -862,7 +859,8 @@
 {
 	pci_unregister_driver(&via686a_pci_driver);
 	if (s_bridge != NULL) {
-		i2c_isa_del_driver(&via686a_driver);
+		platform_device_unregister(pdev);
+		platform_driver_unregister(&via686a_driver);
 		pci_dev_put(s_bridge);
 		s_bridge = NULL;
 	}
diff --git a/drivers/hwmon/vt8231.c b/drivers/hwmon/vt8231.c
index a6a4aa0..c604972 100644
--- a/drivers/hwmon/vt8231.c
+++ b/drivers/hwmon/vt8231.c
@@ -29,8 +29,7 @@
 #include <linux/slab.h>
 #include <linux/pci.h>
 #include <linux/jiffies.h>
-#include <linux/i2c.h>
-#include <linux/i2c-isa.h>
+#include <linux/platform_device.h>
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
 #include <linux/hwmon-vid.h>
@@ -42,10 +41,7 @@
 module_param(force_addr, int, 0);
 MODULE_PARM_DESC(force_addr, "Initialize the base address of the sensors");
 
-/* Device address
-   Note that we can't determine the ISA address until we have initialized
-   our module */
-static unsigned short isa_address;
+static struct platform_device *pdev;
 
 #define VT8231_EXTENT 0x80
 #define VT8231_BASE_REG 0x70
@@ -148,7 +144,9 @@
 #define FAN_FROM_REG(val, div) ((val) == 0 ? 0 : 1310720 / ((val) * (div)))
 
 struct vt8231_data {
-	struct i2c_client client;
+	unsigned short addr;
+	const char *name;
+
 	struct mutex update_lock;
 	struct class_device *class_dev;
 	char valid;		/* !=0 if following fields are valid */
@@ -168,20 +166,20 @@
 };
 
 static struct pci_dev *s_bridge;
-static int vt8231_detect(struct i2c_adapter *adapter);
-static int vt8231_detach_client(struct i2c_client *client);
+static int vt8231_probe(struct platform_device *pdev);
+static int vt8231_remove(struct platform_device *pdev);
 static struct vt8231_data *vt8231_update_device(struct device *dev);
-static void vt8231_init_client(struct i2c_client *client);
+static void vt8231_init_device(struct vt8231_data *data);
 
-static inline int vt8231_read_value(struct i2c_client *client, u8 reg)
+static inline int vt8231_read_value(struct vt8231_data *data, u8 reg)
 {
-	return inb_p(client->addr + reg);
+	return inb_p(data->addr + reg);
 }
 
-static inline void vt8231_write_value(struct i2c_client *client, u8 reg,
+static inline void vt8231_write_value(struct vt8231_data *data, u8 reg,
 					u8 value)
 {
-	outb_p(value, client->addr + reg);
+	outb_p(value, data->addr + reg);
 }
 
 /* following are the sysfs callback functions */
@@ -220,13 +218,12 @@
 {
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
-	struct i2c_client *client = to_i2c_client(dev);
-	struct vt8231_data *data = i2c_get_clientdata(client);
+	struct vt8231_data *data = dev_get_drvdata(dev);
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->in_min[nr] = SENSORS_LIMIT(((val * 958) / 10000) + 3, 0, 255);
-	vt8231_write_value(client, regvoltmin[nr], data->in_min[nr]);
+	vt8231_write_value(data, regvoltmin[nr], data->in_min[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -236,13 +233,12 @@
 {
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
-	struct i2c_client *client = to_i2c_client(dev);
-	struct vt8231_data *data = i2c_get_clientdata(client);
+	struct vt8231_data *data = dev_get_drvdata(dev);
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->in_max[nr] = SENSORS_LIMIT(((val * 958) / 10000) + 3, 0, 255);
-	vt8231_write_value(client, regvoltmax[nr], data->in_max[nr]);
+	vt8231_write_value(data, regvoltmax[nr], data->in_max[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -278,14 +274,13 @@
 static ssize_t set_in5_min(struct device *dev, struct device_attribute *attr,
 		const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct vt8231_data *data = i2c_get_clientdata(client);
+	struct vt8231_data *data = dev_get_drvdata(dev);
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->in_min[5] = SENSORS_LIMIT(((val * 958 * 34) / (10000 * 54)) + 3,
 					0, 255);
-	vt8231_write_value(client, regvoltmin[5], data->in_min[5]);
+	vt8231_write_value(data, regvoltmin[5], data->in_min[5]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -293,14 +288,13 @@
 static ssize_t set_in5_max(struct device *dev, struct device_attribute *attr,
 		const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct vt8231_data *data = i2c_get_clientdata(client);
+	struct vt8231_data *data = dev_get_drvdata(dev);
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->in_max[5] = SENSORS_LIMIT(((val * 958 * 34) / (10000 * 54)) + 3,
 					0, 255);
-	vt8231_write_value(client, regvoltmax[5], data->in_max[5]);
+	vt8231_write_value(data, regvoltmax[5], data->in_max[5]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -348,26 +342,24 @@
 static ssize_t set_temp0_max(struct device *dev, struct device_attribute *attr,
 		const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct vt8231_data *data = i2c_get_clientdata(client);
+	struct vt8231_data *data = dev_get_drvdata(dev);
 	int val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->temp_max[0] = SENSORS_LIMIT((val + 500) / 1000, 0, 255);
-	vt8231_write_value(client, regtempmax[0], data->temp_max[0]);
+	vt8231_write_value(data, regtempmax[0], data->temp_max[0]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
 static ssize_t set_temp0_min(struct device *dev, struct device_attribute *attr,
 		const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct vt8231_data *data = i2c_get_clientdata(client);
+	struct vt8231_data *data = dev_get_drvdata(dev);
 	int val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->temp_min[0] = SENSORS_LIMIT((val + 500) / 1000, 0, 255);
-	vt8231_write_value(client, regtempmin[0], data->temp_min[0]);
+	vt8231_write_value(data, regtempmin[0], data->temp_min[0]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -404,13 +396,12 @@
 {
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
-	struct i2c_client *client = to_i2c_client(dev);
-	struct vt8231_data *data = i2c_get_clientdata(client);
+	struct vt8231_data *data = dev_get_drvdata(dev);
 	int val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->temp_max[nr] = SENSORS_LIMIT(TEMP_MAXMIN_TO_REG(val), 0, 255);
-	vt8231_write_value(client, regtempmax[nr], data->temp_max[nr]);
+	vt8231_write_value(data, regtempmax[nr], data->temp_max[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -419,13 +410,12 @@
 {
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
-	struct i2c_client *client = to_i2c_client(dev);
-	struct vt8231_data *data = i2c_get_clientdata(client);
+	struct vt8231_data *data = dev_get_drvdata(dev);
 	int val = simple_strtol(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->temp_min[nr] = SENSORS_LIMIT(TEMP_MAXMIN_TO_REG(val), 0, 255);
-	vt8231_write_value(client, regtempmin[nr], data->temp_min[nr]);
+	vt8231_write_value(data, regtempmin[nr], data->temp_min[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -486,13 +476,12 @@
 {
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
-	struct i2c_client *client = to_i2c_client(dev);
-	struct vt8231_data *data = i2c_get_clientdata(client);
+	struct vt8231_data *data = dev_get_drvdata(dev);
 	int val = simple_strtoul(buf, NULL, 10);
 
 	mutex_lock(&data->update_lock);
 	data->fan_min[nr] = FAN_TO_REG(val, DIV_FROM_REG(data->fan_div[nr]));
-	vt8231_write_value(client, VT8231_REG_FAN_MIN(nr), data->fan_min[nr]);
+	vt8231_write_value(data, VT8231_REG_FAN_MIN(nr), data->fan_min[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -500,12 +489,11 @@
 static ssize_t set_fan_div(struct device *dev, struct device_attribute *attr,
 		const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct vt8231_data *data = i2c_get_clientdata(client);
+	struct vt8231_data *data = dev_get_drvdata(dev);
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	unsigned long val = simple_strtoul(buf, NULL, 10);
 	int nr = sensor_attr->index;
-	int old = vt8231_read_value(client, VT8231_REG_FANDIV);
+	int old = vt8231_read_value(data, VT8231_REG_FANDIV);
 	long min = FAN_FROM_REG(data->fan_min[nr],
 				 DIV_FROM_REG(data->fan_div[nr]));
 
@@ -516,7 +504,7 @@
 	case 4: data->fan_div[nr] = 2; break;
 	case 8: data->fan_div[nr] = 3; break;
 	default:
-		dev_err(&client->dev, "fan_div value %ld not supported."
+		dev_err(dev, "fan_div value %ld not supported."
 		        "Choose one of 1, 2, 4 or 8!\n", val);
 		mutex_unlock(&data->update_lock);
 		return -EINVAL;
@@ -524,10 +512,10 @@
 
 	/* Correct the fan minimum speed */
 	data->fan_min[nr] = FAN_TO_REG(min, DIV_FROM_REG(data->fan_div[nr]));
-	vt8231_write_value(client, VT8231_REG_FAN_MIN(nr), data->fan_min[nr]);
+	vt8231_write_value(data, VT8231_REG_FAN_MIN(nr), data->fan_min[nr]);
 
 	old = (old & 0x0f) | (data->fan_div[1] << 6) | (data->fan_div[0] << 4);
-	vt8231_write_value(client, VT8231_REG_FANDIV, old);
+	vt8231_write_value(data, VT8231_REG_FANDIV, old);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -551,9 +539,16 @@
 	struct vt8231_data *data = vt8231_update_device(dev);
 	return sprintf(buf, "%d\n", data->alarms);
 }
-
 static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
 
+static ssize_t show_name(struct device *dev, struct device_attribute
+			 *devattr, char *buf)
+{
+	struct vt8231_data *data = dev_get_drvdata(dev);
+	return sprintf(buf, "%s\n", data->name);
+}
+static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
+
 static struct attribute *vt8231_attributes_temps[6][4] = {
 	{
 		&dev_attr_temp1_input.attr,
@@ -648,6 +643,7 @@
 	&sensor_dev_attr_fan1_div.dev_attr.attr,
 	&sensor_dev_attr_fan2_div.dev_attr.attr,
 	&dev_attr_alarms.attr,
+	&dev_attr_name.attr,
 	NULL
 };
 
@@ -655,13 +651,13 @@
 	.attrs = vt8231_attributes,
 };
 
-static struct i2c_driver vt8231_driver = {
+static struct platform_driver vt8231_driver = {
 	.driver = {
 		.owner	= THIS_MODULE,
 		.name	= "vt8231",
 	},
-	.attach_adapter	= vt8231_detect,
-	.detach_client	= vt8231_detach_client,
+	.probe	= vt8231_probe,
+	.remove	= __devexit_p(vt8231_remove),
 };
 
 static struct pci_device_id vt8231_pci_ids[] = {
@@ -680,40 +676,18 @@
 	.probe		= vt8231_pci_probe,
 };
 
-int vt8231_detect(struct i2c_adapter *adapter)
+int vt8231_probe(struct platform_device *pdev)
 {
-	struct i2c_client *client;
+	struct resource *res;
 	struct vt8231_data *data;
 	int err = 0, i;
-	u16 val;
-
-	/* 8231 requires multiple of 256 */
-	if (force_addr)	{
-		isa_address = force_addr & 0xFF00;
-		dev_warn(&adapter->dev, "forcing ISA address 0x%04X\n",
-				 isa_address);
-		if (PCIBIOS_SUCCESSFUL != pci_write_config_word(s_bridge,
-						VT8231_BASE_REG, isa_address))
-			return -ENODEV;
-	}
-
-	if (PCIBIOS_SUCCESSFUL !=
-		pci_read_config_word(s_bridge, VT8231_ENABLE_REG, &val))
-		return -ENODEV;
-
-	if (!(val & 0x0001)) {
-		dev_warn(&adapter->dev, "enabling sensors\n");
-		if (PCIBIOS_SUCCESSFUL !=
-			pci_write_config_word(s_bridge, VT8231_ENABLE_REG,
-							  val | 0x0001))
-			return -ENODEV;
-	}
 
 	/* Reserve the ISA region */
-	if (!request_region(isa_address, VT8231_EXTENT,
-			    vt8231_pci_driver.name)) {
-		dev_err(&adapter->dev, "region 0x%x already in use!\n",
-			   isa_address);
+	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+	if (!request_region(res->start, VT8231_EXTENT,
+			    vt8231_driver.driver.name)) {
+		dev_err(&pdev->dev, "Region 0x%lx-0x%lx already in use!\n",
+			(unsigned long)res->start, (unsigned long)res->end);
 		return -ENODEV;
 	}
 
@@ -722,33 +696,23 @@
 		goto exit_release;
 	}
 
-	client = &data->client;
-	i2c_set_clientdata(client, data);
-	client->addr = isa_address;
-	client->adapter = adapter;
-	client->driver = &vt8231_driver;
-
-	/* Fill in the remaining client fields and put into the global list */
-	strlcpy(client->name, "vt8231", I2C_NAME_SIZE);
+	platform_set_drvdata(pdev, data);
+	data->addr = res->start;
+	data->name = "vt8231";
 
 	mutex_init(&data->update_lock);
-
-	/* Tell the I2C layer a new client has arrived */
-	if ((err = i2c_attach_client(client)))
-		goto exit_free;
-
-	vt8231_init_client(client);
+	vt8231_init_device(data);
 
 	/* Register sysfs hooks */
-	if ((err = sysfs_create_group(&client->dev.kobj, &vt8231_group)))
-		goto exit_detach;
+	if ((err = sysfs_create_group(&pdev->dev.kobj, &vt8231_group)))
+		goto exit_free;
 
 	/* Must update device information to find out the config field */
-	data->uch_config = vt8231_read_value(client, VT8231_REG_UCH_CONFIG);
+	data->uch_config = vt8231_read_value(data, VT8231_REG_UCH_CONFIG);
 
 	for (i = 0; i < ARRAY_SIZE(vt8231_group_temps); i++) {
 		if (ISTEMP(i, data->uch_config)) {
-			if ((err = sysfs_create_group(&client->dev.kobj,
+			if ((err = sysfs_create_group(&pdev->dev.kobj,
 					&vt8231_group_temps[i])))
 				goto exit_remove_files;
 		}
@@ -756,13 +720,13 @@
 
 	for (i = 0; i < ARRAY_SIZE(vt8231_group_volts); i++) {
 		if (ISVOLT(i, data->uch_config)) {
-			if ((err = sysfs_create_group(&client->dev.kobj,
+			if ((err = sysfs_create_group(&pdev->dev.kobj,
 					&vt8231_group_volts[i])))
 				goto exit_remove_files;
 		}
 	}
 
-	data->class_dev = hwmon_device_register(&client->dev);
+	data->class_dev = hwmon_device_register(&pdev->dev);
 	if (IS_ERR(data->class_dev)) {
 		err = PTR_ERR(data->class_dev);
 		goto exit_remove_files;
@@ -771,56 +735,52 @@
 
 exit_remove_files:
 	for (i = 0; i < ARRAY_SIZE(vt8231_group_volts); i++)
-		sysfs_remove_group(&client->dev.kobj, &vt8231_group_volts[i]);
+		sysfs_remove_group(&pdev->dev.kobj, &vt8231_group_volts[i]);
 
 	for (i = 0; i < ARRAY_SIZE(vt8231_group_temps); i++)
-		sysfs_remove_group(&client->dev.kobj, &vt8231_group_temps[i]);
+		sysfs_remove_group(&pdev->dev.kobj, &vt8231_group_temps[i]);
 
-	sysfs_remove_group(&client->dev.kobj, &vt8231_group);
-exit_detach:
-	i2c_detach_client(client);
+	sysfs_remove_group(&pdev->dev.kobj, &vt8231_group);
+
 exit_free:
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
+
 exit_release:
-	release_region(isa_address, VT8231_EXTENT);
+	release_region(res->start, VT8231_EXTENT);
 	return err;
 }
 
-static int vt8231_detach_client(struct i2c_client *client)
+static int vt8231_remove(struct platform_device *pdev)
 {
-	struct vt8231_data *data = i2c_get_clientdata(client);
-	int err, i;
+	struct vt8231_data *data = platform_get_drvdata(pdev);
+	int i;
 
 	hwmon_device_unregister(data->class_dev);
 
 	for (i = 0; i < ARRAY_SIZE(vt8231_group_volts); i++)
-		sysfs_remove_group(&client->dev.kobj, &vt8231_group_volts[i]);
+		sysfs_remove_group(&pdev->dev.kobj, &vt8231_group_volts[i]);
 
 	for (i = 0; i < ARRAY_SIZE(vt8231_group_temps); i++)
-		sysfs_remove_group(&client->dev.kobj, &vt8231_group_temps[i]);
+		sysfs_remove_group(&pdev->dev.kobj, &vt8231_group_temps[i]);
 
-	sysfs_remove_group(&client->dev.kobj, &vt8231_group);
+	sysfs_remove_group(&pdev->dev.kobj, &vt8231_group);
 
-	if ((err = i2c_detach_client(client))) {
-		return err;
-	}
-
-	release_region(client->addr, VT8231_EXTENT);
+	release_region(data->addr, VT8231_EXTENT);
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
-
 	return 0;
 }
 
-static void vt8231_init_client(struct i2c_client *client)
+static void vt8231_init_device(struct vt8231_data *data)
 {
-	vt8231_write_value(client, VT8231_REG_TEMP1_CONFIG, 0);
-	vt8231_write_value(client, VT8231_REG_TEMP2_CONFIG, 0);
+	vt8231_write_value(data, VT8231_REG_TEMP1_CONFIG, 0);
+	vt8231_write_value(data, VT8231_REG_TEMP2_CONFIG, 0);
 }
 
 static struct vt8231_data *vt8231_update_device(struct device *dev)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct vt8231_data *data = i2c_get_clientdata(client);
+	struct vt8231_data *data = dev_get_drvdata(dev);
 	int i;
 	u16 low;
 
@@ -830,41 +790,41 @@
 	    || !data->valid) {
 		for (i = 0; i < 6; i++) {
 			if (ISVOLT(i, data->uch_config)) {
-				data->in[i] = vt8231_read_value(client,
+				data->in[i] = vt8231_read_value(data,
 						regvolt[i]);
-				data->in_min[i] = vt8231_read_value(client,
+				data->in_min[i] = vt8231_read_value(data,
 						regvoltmin[i]);
-				data->in_max[i] = vt8231_read_value(client,
+				data->in_max[i] = vt8231_read_value(data,
 						regvoltmax[i]);
 			}
 		}
 		for (i = 0; i < 2; i++) {
-			data->fan[i] = vt8231_read_value(client,
+			data->fan[i] = vt8231_read_value(data,
 						VT8231_REG_FAN(i));
-			data->fan_min[i] = vt8231_read_value(client,
+			data->fan_min[i] = vt8231_read_value(data,
 						VT8231_REG_FAN_MIN(i));
 		}
 
-		low = vt8231_read_value(client, VT8231_REG_TEMP_LOW01);
+		low = vt8231_read_value(data, VT8231_REG_TEMP_LOW01);
 		low = (low >> 6) | ((low & 0x30) >> 2)
-		    | (vt8231_read_value(client, VT8231_REG_TEMP_LOW25) << 4);
+		    | (vt8231_read_value(data, VT8231_REG_TEMP_LOW25) << 4);
 		for (i = 0; i < 6; i++) {
 			if (ISTEMP(i, data->uch_config)) {
-				data->temp[i] = (vt8231_read_value(client,
+				data->temp[i] = (vt8231_read_value(data,
 						       regtemp[i]) << 2)
 						| ((low >> (2 * i)) & 0x03);
-				data->temp_max[i] = vt8231_read_value(client,
+				data->temp_max[i] = vt8231_read_value(data,
 						      regtempmax[i]);
-				data->temp_min[i] = vt8231_read_value(client,
+				data->temp_min[i] = vt8231_read_value(data,
 						      regtempmin[i]);
 			}
 		}
 
-		i = vt8231_read_value(client, VT8231_REG_FANDIV);
+		i = vt8231_read_value(data, VT8231_REG_FANDIV);
 		data->fan_div[0] = (i >> 4) & 0x03;
 		data->fan_div[1] = i >> 6;
-		data->alarms = vt8231_read_value(client, VT8231_REG_ALARM1) |
-			(vt8231_read_value(client, VT8231_REG_ALARM2) << 8);
+		data->alarms = vt8231_read_value(data, VT8231_REG_ALARM1) |
+			(vt8231_read_value(data, VT8231_REG_ALARM2) << 8);
 
 		/* Set alarm flags correctly */
 		if (!data->fan[0] && data->fan_min[0]) {
@@ -888,33 +848,102 @@
 	return data;
 }
 
+static int __devinit vt8231_device_add(unsigned short address)
+{
+	struct resource res = {
+		.start	= address,
+		.end	= address + VT8231_EXTENT - 1,
+		.name	= "vt8231",
+		.flags	= IORESOURCE_IO,
+	};
+	int err;
+
+	pdev = platform_device_alloc("vt8231", address);
+	if (!pdev) {
+		err = -ENOMEM;
+		printk(KERN_ERR "vt8231: Device allocation failed\n");
+		goto exit;
+	}
+
+	err = platform_device_add_resources(pdev, &res, 1);
+	if (err) {
+		printk(KERN_ERR "vt8231: Device resource addition failed "
+		       "(%d)\n", err);
+		goto exit_device_put;
+	}
+
+	err = platform_device_add(pdev);
+	if (err) {
+		printk(KERN_ERR "vt8231: Device addition failed (%d)\n",
+		       err);
+		goto exit_device_put;
+	}
+
+	return 0;
+
+exit_device_put:
+	platform_device_put(pdev);
+exit:
+	return err;
+}
+
 static int __devinit vt8231_pci_probe(struct pci_dev *dev,
 				const struct pci_device_id *id)
 {
-	u16 val;
+	u16 address, val;
+	if (force_addr) {
+		address = force_addr & 0xff00;
+		dev_warn(&dev->dev, "Forcing ISA address 0x%x\n",
+			 address);
+
+		if (PCIBIOS_SUCCESSFUL !=
+		    pci_write_config_word(dev, VT8231_BASE_REG, address | 1))
+			return -ENODEV;
+	}
 
 	if (PCIBIOS_SUCCESSFUL != pci_read_config_word(dev, VT8231_BASE_REG,
 							&val))
 		return -ENODEV;
 
-	isa_address = val & ~(VT8231_EXTENT - 1);
-	if (isa_address == 0 && force_addr == 0) {
+	address = val & ~(VT8231_EXTENT - 1);
+	if (address == 0) {
 		dev_err(&dev->dev, "base address not set -\
 				 upgrade BIOS or use force_addr=0xaddr\n");
 		return -ENODEV;
 	}
 
-	s_bridge = pci_dev_get(dev);
+	if (PCIBIOS_SUCCESSFUL != pci_read_config_word(dev, VT8231_ENABLE_REG,
+							&val))
+		return -ENODEV;
 
-	if (i2c_isa_add_driver(&vt8231_driver)) {
-		pci_dev_put(s_bridge);
-		s_bridge = NULL;
+	if (!(val & 0x0001)) {
+		dev_warn(&dev->dev, "enabling sensors\n");
+		if (PCIBIOS_SUCCESSFUL !=
+			pci_write_config_word(dev, VT8231_ENABLE_REG,
+							val | 0x0001))
+			return -ENODEV;
 	}
 
+	if (platform_driver_register(&vt8231_driver))
+		goto exit;
+
+	/* Sets global pdev as a side effect */
+	if (vt8231_device_add(address))
+		goto exit_unregister;
+
 	/* Always return failure here.  This is to allow other drivers to bind
 	 * to this pci device.  We don't really want to have control over the
 	 * pci device, we only wanted to read as few register values from it.
 	 */
+
+	/* We do, however, mark ourselves as using the PCI device to stop it
+	   getting unloaded. */
+	s_bridge = pci_dev_get(dev);
+	return -ENODEV;
+
+exit_unregister:
+	platform_driver_unregister(&vt8231_driver);
+exit:
 	return -ENODEV;
 }
 
@@ -927,7 +956,8 @@
 {
 	pci_unregister_driver(&vt8231_pci_driver);
 	if (s_bridge != NULL) {
-		i2c_isa_del_driver(&vt8231_driver);
+		platform_device_unregister(pdev);
+		platform_driver_unregister(&vt8231_driver);
 		pci_dev_put(s_bridge);
 		s_bridge = NULL;
 	}
diff --git a/drivers/hwmon/w83627ehf.c b/drivers/hwmon/w83627ehf.c
index 30a7640..c51ae2e 100644
--- a/drivers/hwmon/w83627ehf.c
+++ b/drivers/hwmon/w83627ehf.c
@@ -41,41 +41,39 @@
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
-#include <linux/i2c.h>
-#include <linux/i2c-isa.h>
+#include <linux/jiffies.h>
+#include <linux/platform_device.h>
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
+#include <linux/hwmon-vid.h>
 #include <linux/err.h>
 #include <linux/mutex.h>
 #include <asm/io.h>
 #include "lm75.h"
 
-/* The actual ISA address is read from Super-I/O configuration space */
-static unsigned short address;
+enum kinds { w83627ehf, w83627dhg };
+
+/* used to set data->name = w83627ehf_device_names[data->sio_kind] */
+static const char * w83627ehf_device_names[] = {
+	"w83627ehf",
+	"w83627dhg",
+};
+
+#define DRVNAME "w83627ehf"
 
 /*
  * Super-I/O constants and functions
  */
 
-/*
- * The three following globals are initialized in w83627ehf_find(), before
- * the i2c-isa device is created. Otherwise, they could be stored in
- * w83627ehf_data. This is ugly, but necessary, and when the driver is next
- * updated to become a platform driver, the globals will disappear.
- */
-static int REG;		/* The register to read/write */
-static int VAL;		/* The value to read/write */
-/* The w83627ehf/ehg have 10 voltage inputs, but the w83627dhg has 9. This
- * value is also used in w83627ehf_detect() to export a device name in sysfs
- * (e.g. w83627ehf or w83627dhg) */
-static int w83627ehf_num_in;
-
 #define W83627EHF_LD_HWM	0x0b
 
 #define SIO_REG_LDSEL		0x07	/* Logical device select */
 #define SIO_REG_DEVID		0x20	/* Device ID (2 bytes) */
+#define SIO_REG_EN_VRM10	0x2C	/* GPIO3, GPIO4 selection */
 #define SIO_REG_ENABLE		0x30	/* Logical device enable */
 #define SIO_REG_ADDR		0x60	/* Logical device address (2 bytes) */
+#define SIO_REG_VID_CTRL	0xF0	/* VID control */
+#define SIO_REG_VID_DATA	0xF1	/* VID data */
 
 #define SIO_W83627EHF_ID	0x8850
 #define SIO_W83627EHG_ID	0x8860
@@ -83,38 +81,38 @@
 #define SIO_ID_MASK		0xFFF0
 
 static inline void
-superio_outb(int reg, int val)
+superio_outb(int ioreg, int reg, int val)
 {
-	outb(reg, REG);
-	outb(val, VAL);
+	outb(reg, ioreg);
+	outb(val, ioreg + 1);
 }
 
 static inline int
-superio_inb(int reg)
+superio_inb(int ioreg, int reg)
 {
-	outb(reg, REG);
-	return inb(VAL);
+	outb(reg, ioreg);
+	return inb(ioreg + 1);
 }
 
 static inline void
-superio_select(int ld)
+superio_select(int ioreg, int ld)
 {
-	outb(SIO_REG_LDSEL, REG);
-	outb(ld, VAL);
+	outb(SIO_REG_LDSEL, ioreg);
+	outb(ld, ioreg + 1);
 }
 
 static inline void
-superio_enter(void)
+superio_enter(int ioreg)
 {
-	outb(0x87, REG);
-	outb(0x87, REG);
+	outb(0x87, ioreg);
+	outb(0x87, ioreg);
 }
 
 static inline void
-superio_exit(void)
+superio_exit(int ioreg)
 {
-	outb(0x02, REG);
-	outb(0x02, VAL);
+	outb(0x02, ioreg);
+	outb(0x02, ioreg + 1);
 }
 
 /*
@@ -124,8 +122,8 @@
 #define IOREGION_ALIGNMENT	~7
 #define IOREGION_OFFSET		5
 #define IOREGION_LENGTH		2
-#define ADDR_REG_OFFSET		5
-#define DATA_REG_OFFSET		6
+#define ADDR_REG_OFFSET		0
+#define DATA_REG_OFFSET		1
 
 #define W83627EHF_REG_BANK		0x4E
 #define W83627EHF_REG_CONFIG		0x40
@@ -255,7 +253,9 @@
  */
 
 struct w83627ehf_data {
-	struct i2c_client client;
+	int addr;	/* IO base of hw monitor block */
+	const char *name;
+
 	struct class_device *class_dev;
 	struct mutex lock;
 
@@ -264,6 +264,7 @@
 	unsigned long last_updated;	/* In jiffies */
 
 	/* Register values */
+	u8 in_num;		/* number of in inputs we have */
 	u8 in[10];		/* Register value */
 	u8 in_max[10];		/* Register value */
 	u8 in_min[10];		/* Register value */
@@ -271,6 +272,7 @@
 	u8 fan_min[5];
 	u8 fan_div[5];
 	u8 has_fan;		/* some fan inputs can be disabled */
+	u8 temp_type[3];
 	s8 temp1;
 	s8 temp1_max;
 	s8 temp1_max_hyst;
@@ -288,6 +290,14 @@
 
 	u8 fan_min_output[4]; /* minimum fan speed */
 	u8 fan_stop_time[4];
+
+	u8 vid;
+	u8 vrm;
+};
+
+struct w83627ehf_sio_data {
+	int sioreg;
+	enum kinds kind;
 };
 
 static inline int is_word_sized(u16 reg)
@@ -303,156 +313,152 @@
    nothing for registers which live in bank 0. For others, they respectively
    set the bank register to the correct value (before the register is
    accessed), and back to 0 (afterwards). */
-static inline void w83627ehf_set_bank(struct i2c_client *client, u16 reg)
+static inline void w83627ehf_set_bank(struct w83627ehf_data *data, u16 reg)
 {
 	if (reg & 0xff00) {
-		outb_p(W83627EHF_REG_BANK, client->addr + ADDR_REG_OFFSET);
-		outb_p(reg >> 8, client->addr + DATA_REG_OFFSET);
+		outb_p(W83627EHF_REG_BANK, data->addr + ADDR_REG_OFFSET);
+		outb_p(reg >> 8, data->addr + DATA_REG_OFFSET);
 	}
 }
 
-static inline void w83627ehf_reset_bank(struct i2c_client *client, u16 reg)
+static inline void w83627ehf_reset_bank(struct w83627ehf_data *data, u16 reg)
 {
 	if (reg & 0xff00) {
-		outb_p(W83627EHF_REG_BANK, client->addr + ADDR_REG_OFFSET);
-		outb_p(0, client->addr + DATA_REG_OFFSET);
+		outb_p(W83627EHF_REG_BANK, data->addr + ADDR_REG_OFFSET);
+		outb_p(0, data->addr + DATA_REG_OFFSET);
 	}
 }
 
-static u16 w83627ehf_read_value(struct i2c_client *client, u16 reg)
+static u16 w83627ehf_read_value(struct w83627ehf_data *data, u16 reg)
 {
-	struct w83627ehf_data *data = i2c_get_clientdata(client);
 	int res, word_sized = is_word_sized(reg);
 
 	mutex_lock(&data->lock);
 
-	w83627ehf_set_bank(client, reg);
-	outb_p(reg & 0xff, client->addr + ADDR_REG_OFFSET);
-	res = inb_p(client->addr + DATA_REG_OFFSET);
+	w83627ehf_set_bank(data, reg);
+	outb_p(reg & 0xff, data->addr + ADDR_REG_OFFSET);
+	res = inb_p(data->addr + DATA_REG_OFFSET);
 	if (word_sized) {
 		outb_p((reg & 0xff) + 1,
-		       client->addr + ADDR_REG_OFFSET);
-		res = (res << 8) + inb_p(client->addr + DATA_REG_OFFSET);
+		       data->addr + ADDR_REG_OFFSET);
+		res = (res << 8) + inb_p(data->addr + DATA_REG_OFFSET);
 	}
-	w83627ehf_reset_bank(client, reg);
+	w83627ehf_reset_bank(data, reg);
 
 	mutex_unlock(&data->lock);
 
 	return res;
 }
 
-static int w83627ehf_write_value(struct i2c_client *client, u16 reg, u16 value)
+static int w83627ehf_write_value(struct w83627ehf_data *data, u16 reg, u16 value)
 {
-	struct w83627ehf_data *data = i2c_get_clientdata(client);
 	int word_sized = is_word_sized(reg);
 
 	mutex_lock(&data->lock);
 
-	w83627ehf_set_bank(client, reg);
-	outb_p(reg & 0xff, client->addr + ADDR_REG_OFFSET);
+	w83627ehf_set_bank(data, reg);
+	outb_p(reg & 0xff, data->addr + ADDR_REG_OFFSET);
 	if (word_sized) {
-		outb_p(value >> 8, client->addr + DATA_REG_OFFSET);
+		outb_p(value >> 8, data->addr + DATA_REG_OFFSET);
 		outb_p((reg & 0xff) + 1,
-		       client->addr + ADDR_REG_OFFSET);
+		       data->addr + ADDR_REG_OFFSET);
 	}
-	outb_p(value & 0xff, client->addr + DATA_REG_OFFSET);
-	w83627ehf_reset_bank(client, reg);
+	outb_p(value & 0xff, data->addr + DATA_REG_OFFSET);
+	w83627ehf_reset_bank(data, reg);
 
 	mutex_unlock(&data->lock);
 	return 0;
 }
 
 /* This function assumes that the caller holds data->update_lock */
-static void w83627ehf_write_fan_div(struct i2c_client *client, int nr)
+static void w83627ehf_write_fan_div(struct w83627ehf_data *data, int nr)
 {
-	struct w83627ehf_data *data = i2c_get_clientdata(client);
 	u8 reg;
 
 	switch (nr) {
 	case 0:
-		reg = (w83627ehf_read_value(client, W83627EHF_REG_FANDIV1) & 0xcf)
+		reg = (w83627ehf_read_value(data, W83627EHF_REG_FANDIV1) & 0xcf)
 		    | ((data->fan_div[0] & 0x03) << 4);
 		/* fan5 input control bit is write only, compute the value */
 		reg |= (data->has_fan & (1 << 4)) ? 1 : 0;
-		w83627ehf_write_value(client, W83627EHF_REG_FANDIV1, reg);
-		reg = (w83627ehf_read_value(client, W83627EHF_REG_VBAT) & 0xdf)
+		w83627ehf_write_value(data, W83627EHF_REG_FANDIV1, reg);
+		reg = (w83627ehf_read_value(data, W83627EHF_REG_VBAT) & 0xdf)
 		    | ((data->fan_div[0] & 0x04) << 3);
-		w83627ehf_write_value(client, W83627EHF_REG_VBAT, reg);
+		w83627ehf_write_value(data, W83627EHF_REG_VBAT, reg);
 		break;
 	case 1:
-		reg = (w83627ehf_read_value(client, W83627EHF_REG_FANDIV1) & 0x3f)
+		reg = (w83627ehf_read_value(data, W83627EHF_REG_FANDIV1) & 0x3f)
 		    | ((data->fan_div[1] & 0x03) << 6);
 		/* fan5 input control bit is write only, compute the value */
 		reg |= (data->has_fan & (1 << 4)) ? 1 : 0;
-		w83627ehf_write_value(client, W83627EHF_REG_FANDIV1, reg);
-		reg = (w83627ehf_read_value(client, W83627EHF_REG_VBAT) & 0xbf)
+		w83627ehf_write_value(data, W83627EHF_REG_FANDIV1, reg);
+		reg = (w83627ehf_read_value(data, W83627EHF_REG_VBAT) & 0xbf)
 		    | ((data->fan_div[1] & 0x04) << 4);
-		w83627ehf_write_value(client, W83627EHF_REG_VBAT, reg);
+		w83627ehf_write_value(data, W83627EHF_REG_VBAT, reg);
 		break;
 	case 2:
-		reg = (w83627ehf_read_value(client, W83627EHF_REG_FANDIV2) & 0x3f)
+		reg = (w83627ehf_read_value(data, W83627EHF_REG_FANDIV2) & 0x3f)
 		    | ((data->fan_div[2] & 0x03) << 6);
-		w83627ehf_write_value(client, W83627EHF_REG_FANDIV2, reg);
-		reg = (w83627ehf_read_value(client, W83627EHF_REG_VBAT) & 0x7f)
+		w83627ehf_write_value(data, W83627EHF_REG_FANDIV2, reg);
+		reg = (w83627ehf_read_value(data, W83627EHF_REG_VBAT) & 0x7f)
 		    | ((data->fan_div[2] & 0x04) << 5);
-		w83627ehf_write_value(client, W83627EHF_REG_VBAT, reg);
+		w83627ehf_write_value(data, W83627EHF_REG_VBAT, reg);
 		break;
 	case 3:
-		reg = (w83627ehf_read_value(client, W83627EHF_REG_DIODE) & 0xfc)
+		reg = (w83627ehf_read_value(data, W83627EHF_REG_DIODE) & 0xfc)
 		    | (data->fan_div[3] & 0x03);
-		w83627ehf_write_value(client, W83627EHF_REG_DIODE, reg);
-		reg = (w83627ehf_read_value(client, W83627EHF_REG_SMI_OVT) & 0x7f)
+		w83627ehf_write_value(data, W83627EHF_REG_DIODE, reg);
+		reg = (w83627ehf_read_value(data, W83627EHF_REG_SMI_OVT) & 0x7f)
 		    | ((data->fan_div[3] & 0x04) << 5);
-		w83627ehf_write_value(client, W83627EHF_REG_SMI_OVT, reg);
+		w83627ehf_write_value(data, W83627EHF_REG_SMI_OVT, reg);
 		break;
 	case 4:
-		reg = (w83627ehf_read_value(client, W83627EHF_REG_DIODE) & 0x73)
+		reg = (w83627ehf_read_value(data, W83627EHF_REG_DIODE) & 0x73)
 		    | ((data->fan_div[4] & 0x03) << 2)
 		    | ((data->fan_div[4] & 0x04) << 5);
-		w83627ehf_write_value(client, W83627EHF_REG_DIODE, reg);
+		w83627ehf_write_value(data, W83627EHF_REG_DIODE, reg);
 		break;
 	}
 }
 
 static struct w83627ehf_data *w83627ehf_update_device(struct device *dev)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct w83627ehf_data *data = i2c_get_clientdata(client);
+	struct w83627ehf_data *data = dev_get_drvdata(dev);
 	int pwmcfg = 0, tolerance = 0; /* shut up the compiler */
 	int i;
 
 	mutex_lock(&data->update_lock);
 
-	if (time_after(jiffies, data->last_updated + HZ)
+	if (time_after(jiffies, data->last_updated + HZ + HZ/2)
 	 || !data->valid) {
 		/* Fan clock dividers */
-		i = w83627ehf_read_value(client, W83627EHF_REG_FANDIV1);
+		i = w83627ehf_read_value(data, W83627EHF_REG_FANDIV1);
 		data->fan_div[0] = (i >> 4) & 0x03;
 		data->fan_div[1] = (i >> 6) & 0x03;
-		i = w83627ehf_read_value(client, W83627EHF_REG_FANDIV2);
+		i = w83627ehf_read_value(data, W83627EHF_REG_FANDIV2);
 		data->fan_div[2] = (i >> 6) & 0x03;
-		i = w83627ehf_read_value(client, W83627EHF_REG_VBAT);
+		i = w83627ehf_read_value(data, W83627EHF_REG_VBAT);
 		data->fan_div[0] |= (i >> 3) & 0x04;
 		data->fan_div[1] |= (i >> 4) & 0x04;
 		data->fan_div[2] |= (i >> 5) & 0x04;
 		if (data->has_fan & ((1 << 3) | (1 << 4))) {
-			i = w83627ehf_read_value(client, W83627EHF_REG_DIODE);
+			i = w83627ehf_read_value(data, W83627EHF_REG_DIODE);
 			data->fan_div[3] = i & 0x03;
 			data->fan_div[4] = ((i >> 2) & 0x03)
 					 | ((i >> 5) & 0x04);
 		}
 		if (data->has_fan & (1 << 3)) {
-			i = w83627ehf_read_value(client, W83627EHF_REG_SMI_OVT);
+			i = w83627ehf_read_value(data, W83627EHF_REG_SMI_OVT);
 			data->fan_div[3] |= (i >> 5) & 0x04;
 		}
 
 		/* Measured voltages and limits */
-		for (i = 0; i < w83627ehf_num_in; i++) {
-			data->in[i] = w83627ehf_read_value(client,
+		for (i = 0; i < data->in_num; i++) {
+			data->in[i] = w83627ehf_read_value(data,
 				      W83627EHF_REG_IN(i));
-			data->in_min[i] = w83627ehf_read_value(client,
+			data->in_min[i] = w83627ehf_read_value(data,
 					  W83627EHF_REG_IN_MIN(i));
-			data->in_max[i] = w83627ehf_read_value(client,
+			data->in_max[i] = w83627ehf_read_value(data,
 					  W83627EHF_REG_IN_MAX(i));
 		}
 
@@ -461,9 +467,9 @@
 			if (!(data->has_fan & (1 << i)))
 				continue;
 
-			data->fan[i] = w83627ehf_read_value(client,
+			data->fan[i] = w83627ehf_read_value(data,
 				       W83627EHF_REG_FAN[i]);
-			data->fan_min[i] = w83627ehf_read_value(client,
+			data->fan_min[i] = w83627ehf_read_value(data,
 					   W83627EHF_REG_FAN_MIN[i]);
 
 			/* If we failed to measure the fan speed and clock
@@ -471,16 +477,16 @@
 			   time */
 			if (data->fan[i] == 0xff
 			 && data->fan_div[i] < 0x07) {
-			 	dev_dbg(&client->dev, "Increasing fan%d "
+			 	dev_dbg(dev, "Increasing fan%d "
 					"clock divider from %u to %u\n",
 					i + 1, div_from_reg(data->fan_div[i]),
 					div_from_reg(data->fan_div[i] + 1));
 				data->fan_div[i]++;
-				w83627ehf_write_fan_div(client, i);
+				w83627ehf_write_fan_div(data, i);
 				/* Preserve min limit if possible */
 				if (data->fan_min[i] >= 2
 				 && data->fan_min[i] != 255)
-					w83627ehf_write_value(client,
+					w83627ehf_write_value(data,
 						W83627EHF_REG_FAN_MIN[i],
 						(data->fan_min[i] /= 2));
 			}
@@ -489,9 +495,9 @@
 		for (i = 0; i < 4; i++) {
 			/* pwmcfg, tolarance mapped for i=0, i=1 to same reg */
 			if (i != 1) {
-				pwmcfg = w83627ehf_read_value(client,
+				pwmcfg = w83627ehf_read_value(data,
 						W83627EHF_REG_PWM_ENABLE[i]);
-				tolerance = w83627ehf_read_value(client,
+				tolerance = w83627ehf_read_value(data,
 						W83627EHF_REG_TOLERANCE[i]);
 			}
 			data->pwm_mode[i] =
@@ -500,14 +506,14 @@
 			data->pwm_enable[i] =
 					((pwmcfg >> W83627EHF_PWM_ENABLE_SHIFT[i])
 						& 3) + 1;
-			data->pwm[i] = w83627ehf_read_value(client,
+			data->pwm[i] = w83627ehf_read_value(data,
 						W83627EHF_REG_PWM[i]);
-			data->fan_min_output[i] = w83627ehf_read_value(client,
+			data->fan_min_output[i] = w83627ehf_read_value(data,
 						W83627EHF_REG_FAN_MIN_OUTPUT[i]);
-			data->fan_stop_time[i] = w83627ehf_read_value(client,
+			data->fan_stop_time[i] = w83627ehf_read_value(data,
 						W83627EHF_REG_FAN_STOP_TIME[i]);
 			data->target_temp[i] =
-				w83627ehf_read_value(client,
+				w83627ehf_read_value(data,
 					W83627EHF_REG_TARGET[i]) &
 					(data->pwm_mode[i] == 1 ? 0x7f : 0xff);
 			data->tolerance[i] = (tolerance >> (i == 1 ? 4 : 0))
@@ -515,26 +521,26 @@
 		}
 
 		/* Measured temperatures and limits */
-		data->temp1 = w83627ehf_read_value(client,
+		data->temp1 = w83627ehf_read_value(data,
 			      W83627EHF_REG_TEMP1);
-		data->temp1_max = w83627ehf_read_value(client,
+		data->temp1_max = w83627ehf_read_value(data,
 				  W83627EHF_REG_TEMP1_OVER);
-		data->temp1_max_hyst = w83627ehf_read_value(client,
+		data->temp1_max_hyst = w83627ehf_read_value(data,
 				       W83627EHF_REG_TEMP1_HYST);
 		for (i = 0; i < 2; i++) {
-			data->temp[i] = w83627ehf_read_value(client,
+			data->temp[i] = w83627ehf_read_value(data,
 					W83627EHF_REG_TEMP[i]);
-			data->temp_max[i] = w83627ehf_read_value(client,
+			data->temp_max[i] = w83627ehf_read_value(data,
 					    W83627EHF_REG_TEMP_OVER[i]);
-			data->temp_max_hyst[i] = w83627ehf_read_value(client,
+			data->temp_max_hyst[i] = w83627ehf_read_value(data,
 						 W83627EHF_REG_TEMP_HYST[i]);
 		}
 
-		data->alarms = w83627ehf_read_value(client,
+		data->alarms = w83627ehf_read_value(data,
 					W83627EHF_REG_ALARM1) |
-			       (w83627ehf_read_value(client,
+			       (w83627ehf_read_value(data,
 					W83627EHF_REG_ALARM2) << 8) |
-			       (w83627ehf_read_value(client,
+			       (w83627ehf_read_value(data,
 					W83627EHF_REG_ALARM3) << 16);
 
 		data->last_updated = jiffies;
@@ -567,15 +573,14 @@
 store_in_##reg (struct device *dev, struct device_attribute *attr, \
 			const char *buf, size_t count) \
 { \
-	struct i2c_client *client = to_i2c_client(dev); \
-	struct w83627ehf_data *data = i2c_get_clientdata(client); \
+	struct w83627ehf_data *data = dev_get_drvdata(dev); \
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \
 	int nr = sensor_attr->index; \
 	u32 val = simple_strtoul(buf, NULL, 10); \
  \
 	mutex_lock(&data->update_lock); \
 	data->in_##reg[nr] = in_to_reg(val, nr); \
-	w83627ehf_write_value(client, W83627EHF_REG_IN_##REG(nr), \
+	w83627ehf_write_value(data, W83627EHF_REG_IN_##REG(nr), \
 			      data->in_##reg[nr]); \
 	mutex_unlock(&data->update_lock); \
 	return count; \
@@ -673,8 +678,7 @@
 store_fan_min(struct device *dev, struct device_attribute *attr,
 	      const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct w83627ehf_data *data = i2c_get_clientdata(client);
+	struct w83627ehf_data *data = dev_get_drvdata(dev);
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 	unsigned int val = simple_strtoul(buf, NULL, 10);
@@ -716,18 +720,25 @@
 	/* Write both the fan clock divider (if it changed) and the new
 	   fan min (unconditionally) */
 	if (new_div != data->fan_div[nr]) {
-		if (new_div > data->fan_div[nr])
-			data->fan[nr] >>= (data->fan_div[nr] - new_div);
-		else
-			data->fan[nr] <<= (new_div - data->fan_div[nr]);
+		/* Preserve the fan speed reading */
+		if (data->fan[nr] != 0xff) {
+			if (new_div > data->fan_div[nr])
+				data->fan[nr] >>= new_div - data->fan_div[nr];
+			else if (data->fan[nr] & 0x80)
+				data->fan[nr] = 0xff;
+			else
+				data->fan[nr] <<= data->fan_div[nr] - new_div;
+		}
 
 		dev_dbg(dev, "fan%u clock divider changed from %u to %u\n",
 			nr + 1, div_from_reg(data->fan_div[nr]),
 			div_from_reg(new_div));
 		data->fan_div[nr] = new_div;
-		w83627ehf_write_fan_div(client, nr);
+		w83627ehf_write_fan_div(data, nr);
+		/* Give the chip time to sample a new speed value */
+		data->last_updated = jiffies;
 	}
-	w83627ehf_write_value(client, W83627EHF_REG_FAN_MIN[nr],
+	w83627ehf_write_value(data, W83627EHF_REG_FAN_MIN[nr],
 			      data->fan_min[nr]);
 	mutex_unlock(&data->update_lock);
 
@@ -788,13 +799,12 @@
 store_temp1_##reg(struct device *dev, struct device_attribute *attr, \
 		  const char *buf, size_t count) \
 { \
-	struct i2c_client *client = to_i2c_client(dev); \
-	struct w83627ehf_data *data = i2c_get_clientdata(client); \
+	struct w83627ehf_data *data = dev_get_drvdata(dev); \
 	u32 val = simple_strtoul(buf, NULL, 10); \
  \
 	mutex_lock(&data->update_lock); \
 	data->temp1_##reg = temp1_to_reg(val, -128000, 127000); \
-	w83627ehf_write_value(client, W83627EHF_REG_TEMP1_##REG, \
+	w83627ehf_write_value(data, W83627EHF_REG_TEMP1_##REG, \
 			      data->temp1_##reg); \
 	mutex_unlock(&data->update_lock); \
 	return count; \
@@ -822,15 +832,14 @@
 store_##reg(struct device *dev, struct device_attribute *attr, \
 	    const char *buf, size_t count) \
 { \
-	struct i2c_client *client = to_i2c_client(dev); \
-	struct w83627ehf_data *data = i2c_get_clientdata(client); \
+	struct w83627ehf_data *data = dev_get_drvdata(dev); \
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \
 	int nr = sensor_attr->index; \
 	u32 val = simple_strtoul(buf, NULL, 10); \
  \
 	mutex_lock(&data->update_lock); \
 	data->reg[nr] = LM75_TEMP_TO_REG(val); \
-	w83627ehf_write_value(client, W83627EHF_REG_TEMP_##REG[nr], \
+	w83627ehf_write_value(data, W83627EHF_REG_TEMP_##REG[nr], \
 			      data->reg[nr]); \
 	mutex_unlock(&data->update_lock); \
 	return count; \
@@ -838,6 +847,15 @@
 store_temp_reg(OVER, temp_max);
 store_temp_reg(HYST, temp_max_hyst);
 
+static ssize_t
+show_temp_type(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct w83627ehf_data *data = w83627ehf_update_device(dev);
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	return sprintf(buf, "%d\n", (int)data->temp_type[nr]);
+}
+
 static struct sensor_device_attribute sda_temp[] = {
 	SENSOR_ATTR(temp1_input, S_IRUGO, show_temp1, NULL, 0),
 	SENSOR_ATTR(temp2_input, S_IRUGO, show_temp, NULL, 0),
@@ -857,6 +875,9 @@
 	SENSOR_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 4),
 	SENSOR_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 5),
 	SENSOR_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 13),
+	SENSOR_ATTR(temp1_type, S_IRUGO, show_temp_type, NULL, 0),
+	SENSOR_ATTR(temp2_type, S_IRUGO, show_temp_type, NULL, 1),
+	SENSOR_ATTR(temp3_type, S_IRUGO, show_temp_type, NULL, 2),
 };
 
 #define show_pwm_reg(reg) \
@@ -877,8 +898,7 @@
 store_pwm_mode(struct device *dev, struct device_attribute *attr,
 			const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct w83627ehf_data *data = i2c_get_clientdata(client);
+	struct w83627ehf_data *data = dev_get_drvdata(dev);
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 	u32 val = simple_strtoul(buf, NULL, 10);
@@ -887,12 +907,12 @@
 	if (val > 1)
 		return -EINVAL;
 	mutex_lock(&data->update_lock);
-	reg = w83627ehf_read_value(client, W83627EHF_REG_PWM_ENABLE[nr]);
+	reg = w83627ehf_read_value(data, W83627EHF_REG_PWM_ENABLE[nr]);
 	data->pwm_mode[nr] = val;
 	reg &= ~(1 << W83627EHF_PWM_MODE_SHIFT[nr]);
 	if (!val)
 		reg |= 1 << W83627EHF_PWM_MODE_SHIFT[nr];
-	w83627ehf_write_value(client, W83627EHF_REG_PWM_ENABLE[nr], reg);
+	w83627ehf_write_value(data, W83627EHF_REG_PWM_ENABLE[nr], reg);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -901,15 +921,14 @@
 store_pwm(struct device *dev, struct device_attribute *attr,
 			const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct w83627ehf_data *data = i2c_get_clientdata(client);
+	struct w83627ehf_data *data = dev_get_drvdata(dev);
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 	u32 val = SENSORS_LIMIT(simple_strtoul(buf, NULL, 10), 0, 255);
 
 	mutex_lock(&data->update_lock);
 	data->pwm[nr] = val;
-	w83627ehf_write_value(client, W83627EHF_REG_PWM[nr], val);
+	w83627ehf_write_value(data, W83627EHF_REG_PWM[nr], val);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -918,8 +937,7 @@
 store_pwm_enable(struct device *dev, struct device_attribute *attr,
 			const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct w83627ehf_data *data = i2c_get_clientdata(client);
+	struct w83627ehf_data *data = dev_get_drvdata(dev);
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 	u32 val = simple_strtoul(buf, NULL, 10);
@@ -928,11 +946,11 @@
 	if (!val || (val > 2))	/* only modes 1 and 2 are supported */
 		return -EINVAL;
 	mutex_lock(&data->update_lock);
-	reg = w83627ehf_read_value(client, W83627EHF_REG_PWM_ENABLE[nr]);
+	reg = w83627ehf_read_value(data, W83627EHF_REG_PWM_ENABLE[nr]);
 	data->pwm_enable[nr] = val;
 	reg &= ~(0x03 << W83627EHF_PWM_ENABLE_SHIFT[nr]);
 	reg |= (val - 1) << W83627EHF_PWM_ENABLE_SHIFT[nr];
-	w83627ehf_write_value(client, W83627EHF_REG_PWM_ENABLE[nr], reg);
+	w83627ehf_write_value(data, W83627EHF_REG_PWM_ENABLE[nr], reg);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -955,15 +973,14 @@
 store_target_temp(struct device *dev, struct device_attribute *attr,
 			const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct w83627ehf_data *data = i2c_get_clientdata(client);
+	struct w83627ehf_data *data = dev_get_drvdata(dev);
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 	u8 val = temp1_to_reg(simple_strtoul(buf, NULL, 10), 0, 127000);
 
 	mutex_lock(&data->update_lock);
 	data->target_temp[nr] = val;
-	w83627ehf_write_value(client, W83627EHF_REG_TARGET[nr], val);
+	w83627ehf_write_value(data, W83627EHF_REG_TARGET[nr], val);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -972,8 +989,7 @@
 store_tolerance(struct device *dev, struct device_attribute *attr,
 			const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct w83627ehf_data *data = i2c_get_clientdata(client);
+	struct w83627ehf_data *data = dev_get_drvdata(dev);
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 	u16 reg;
@@ -981,13 +997,13 @@
 	u8 val = temp1_to_reg(simple_strtoul(buf, NULL, 10), 0, 15000);
 
 	mutex_lock(&data->update_lock);
-	reg = w83627ehf_read_value(client, W83627EHF_REG_TOLERANCE[nr]);
+	reg = w83627ehf_read_value(data, W83627EHF_REG_TOLERANCE[nr]);
 	data->tolerance[nr] = val;
 	if (nr == 1)
 		reg = (reg & 0x0f) | (val << 4);
 	else
 		reg = (reg & 0xf0) | val;
-	w83627ehf_write_value(client, W83627EHF_REG_TOLERANCE[nr], reg);
+	w83627ehf_write_value(data, W83627EHF_REG_TOLERANCE[nr], reg);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -1058,14 +1074,13 @@
 store_##reg(struct device *dev, struct device_attribute *attr, \
 			    const char *buf, size_t count) \
 {\
-	struct i2c_client *client = to_i2c_client(dev); \
-	struct w83627ehf_data *data = i2c_get_clientdata(client); \
+	struct w83627ehf_data *data = dev_get_drvdata(dev); \
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \
 	int nr = sensor_attr->index; \
 	u32 val = SENSORS_LIMIT(simple_strtoul(buf, NULL, 10), 1, 255); \
 	mutex_lock(&data->update_lock); \
 	data->reg[nr] = val; \
-	w83627ehf_write_value(client, W83627EHF_REG_##REG[nr],  val); \
+	w83627ehf_write_value(data, W83627EHF_REG_##REG[nr], val); \
 	mutex_unlock(&data->update_lock); \
 	return count; \
 }
@@ -1087,21 +1102,28 @@
 store_##reg(struct device *dev, struct device_attribute *attr, \
 			const char *buf, size_t count) \
 { \
-	struct i2c_client *client = to_i2c_client(dev); \
-	struct w83627ehf_data *data = i2c_get_clientdata(client); \
+	struct w83627ehf_data *data = dev_get_drvdata(dev); \
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \
 	int nr = sensor_attr->index; \
 	u8 val = step_time_to_reg(simple_strtoul(buf, NULL, 10), \
 					data->pwm_mode[nr]); \
 	mutex_lock(&data->update_lock); \
 	data->reg[nr] = val; \
-	w83627ehf_write_value(client, W83627EHF_REG_##REG[nr], val); \
+	w83627ehf_write_value(data, W83627EHF_REG_##REG[nr], val); \
 	mutex_unlock(&data->update_lock); \
 	return count; \
 } \
 
 fan_time_functions(fan_stop_time, FAN_STOP_TIME)
 
+static ssize_t show_name(struct device *dev, struct device_attribute *attr,
+			 char *buf)
+{
+	struct w83627ehf_data *data = dev_get_drvdata(dev);
+
+	return sprintf(buf, "%s\n", data->name);
+}
+static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
 
 static struct sensor_device_attribute sda_sf3_arrays_fan4[] = {
 	SENSOR_ATTR(pwm4_stop_time, S_IWUSR | S_IRUGO, show_fan_stop_time,
@@ -1125,8 +1147,16 @@
 		    store_fan_min_output, 2),
 };
 
+static ssize_t
+show_vid(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct w83627ehf_data *data = dev_get_drvdata(dev);
+	return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm));
+}
+static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid, NULL);
+
 /*
- * Driver and client management
+ * Driver and device management
  */
 
 static void w83627ehf_device_remove_files(struct device *dev)
@@ -1134,12 +1164,13 @@
 	/* some entries in the following arrays may not have been used in
 	 * device_create_file(), but device_remove_file() will ignore them */
 	int i;
+	struct w83627ehf_data *data = dev_get_drvdata(dev);
 
 	for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays); i++)
 		device_remove_file(dev, &sda_sf3_arrays[i].dev_attr);
 	for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays_fan4); i++)
 		device_remove_file(dev, &sda_sf3_arrays_fan4[i].dev_attr);
-	for (i = 0; i < w83627ehf_num_in; i++) {
+	for (i = 0; i < data->in_num; i++) {
 		device_remove_file(dev, &sda_in_input[i].dev_attr);
 		device_remove_file(dev, &sda_in_alarm[i].dev_attr);
 		device_remove_file(dev, &sda_in_min[i].dev_attr);
@@ -1160,43 +1191,64 @@
 	}
 	for (i = 0; i < ARRAY_SIZE(sda_temp); i++)
 		device_remove_file(dev, &sda_temp[i].dev_attr);
+
+	device_remove_file(dev, &dev_attr_name);
+	if (data->vid != 0x3f)
+		device_remove_file(dev, &dev_attr_cpu0_vid);
 }
 
-static struct i2c_driver w83627ehf_driver;
-
-static void w83627ehf_init_client(struct i2c_client *client)
+/* Get the monitoring functions started */
+static inline void __devinit w83627ehf_init_device(struct w83627ehf_data *data)
 {
 	int i;
-	u8 tmp;
+	u8 tmp, diode;
 
 	/* Start monitoring is needed */
-	tmp = w83627ehf_read_value(client, W83627EHF_REG_CONFIG);
+	tmp = w83627ehf_read_value(data, W83627EHF_REG_CONFIG);
 	if (!(tmp & 0x01))
-		w83627ehf_write_value(client, W83627EHF_REG_CONFIG,
+		w83627ehf_write_value(data, W83627EHF_REG_CONFIG,
 				      tmp | 0x01);
 
 	/* Enable temp2 and temp3 if needed */
 	for (i = 0; i < 2; i++) {
-		tmp = w83627ehf_read_value(client,
+		tmp = w83627ehf_read_value(data,
 					   W83627EHF_REG_TEMP_CONFIG[i]);
 		if (tmp & 0x01)
-			w83627ehf_write_value(client,
+			w83627ehf_write_value(data,
 					      W83627EHF_REG_TEMP_CONFIG[i],
 					      tmp & 0xfe);
 	}
+
+	/* Enable VBAT monitoring if needed */
+	tmp = w83627ehf_read_value(data, W83627EHF_REG_VBAT);
+	if (!(tmp & 0x01))
+		w83627ehf_write_value(data, W83627EHF_REG_VBAT, tmp | 0x01);
+
+	/* Get thermal sensor types */
+	diode = w83627ehf_read_value(data, W83627EHF_REG_DIODE);
+	for (i = 0; i < 3; i++) {
+		if ((tmp & (0x02 << i)))
+			data->temp_type[i] = (diode & (0x10 << i)) ? 1 : 2;
+		else
+			data->temp_type[i] = 4; /* thermistor */
+	}
 }
 
-static int w83627ehf_detect(struct i2c_adapter *adapter)
+static int __devinit w83627ehf_probe(struct platform_device *pdev)
 {
-	struct i2c_client *client;
+	struct device *dev = &pdev->dev;
+	struct w83627ehf_sio_data *sio_data = dev->platform_data;
 	struct w83627ehf_data *data;
-	struct device *dev;
-	u8 fan4pin, fan5pin;
+	struct resource *res;
+	u8 fan4pin, fan5pin, en_vrm10;
 	int i, err = 0;
 
-	if (!request_region(address + IOREGION_OFFSET, IOREGION_LENGTH,
-	                    w83627ehf_driver.driver.name)) {
+	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+	if (!request_region(res->start, IOREGION_LENGTH, DRVNAME)) {
 		err = -EBUSY;
+		dev_err(dev, "Failed to request region 0x%lx-0x%lx\n",
+			(unsigned long)res->start,
+			(unsigned long)res->start + IOREGION_LENGTH - 1);
 		goto exit;
 	}
 
@@ -1205,41 +1257,47 @@
 		goto exit_release;
 	}
 
-	client = &data->client;
-	i2c_set_clientdata(client, data);
-	client->addr = address;
+	data->addr = res->start;
 	mutex_init(&data->lock);
-	client->adapter = adapter;
-	client->driver = &w83627ehf_driver;
-	client->flags = 0;
-	dev = &client->dev;
-
-	if (w83627ehf_num_in == 9)
-		strlcpy(client->name, "w83627dhg", I2C_NAME_SIZE);
-	else	/* just say ehf. 627EHG is 627EHF in lead-free packaging. */
-		strlcpy(client->name, "w83627ehf", I2C_NAME_SIZE);
-
-	data->valid = 0;
 	mutex_init(&data->update_lock);
+	data->name = w83627ehf_device_names[sio_data->kind];
+	platform_set_drvdata(pdev, data);
 
-	/* Tell the i2c layer a new client has arrived */
-	if ((err = i2c_attach_client(client)))
-		goto exit_free;
+	/* 627EHG and 627EHF have 10 voltage inputs; DHG has 9 */
+	data->in_num = (sio_data->kind == w83627dhg) ? 9 : 10;
 
 	/* Initialize the chip */
-	w83627ehf_init_client(client);
+	w83627ehf_init_device(data);
 
-	/* A few vars need to be filled upon startup */
-	for (i = 0; i < 5; i++)
-		data->fan_min[i] = w83627ehf_read_value(client,
-				   W83627EHF_REG_FAN_MIN[i]);
+	data->vrm = vid_which_vrm();
+	superio_enter(sio_data->sioreg);
+	/* Set VID input sensibility if needed. In theory the BIOS should
+	   have set it, but in practice it's not always the case. */
+	en_vrm10 = superio_inb(sio_data->sioreg, SIO_REG_EN_VRM10);
+	if ((en_vrm10 & 0x08) && data->vrm != 100) {
+		dev_warn(dev, "Setting VID input voltage to TTL\n");
+		superio_outb(sio_data->sioreg, SIO_REG_EN_VRM10,
+			     en_vrm10 & ~0x08);
+	} else if (!(en_vrm10 & 0x08) && data->vrm == 100) {
+		dev_warn(dev, "Setting VID input voltage to VRM10\n");
+		superio_outb(sio_data->sioreg, SIO_REG_EN_VRM10,
+			     en_vrm10 | 0x08);
+	}
+	/* Read VID value */
+	superio_select(sio_data->sioreg, W83627EHF_LD_HWM);
+	if (superio_inb(sio_data->sioreg, SIO_REG_VID_CTRL) & 0x80)
+		data->vid = superio_inb(sio_data->sioreg, SIO_REG_VID_DATA) & 0x3f;
+	else {
+		dev_info(dev, "VID pins in output mode, CPU VID not "
+			 "available\n");
+		data->vid = 0x3f;
+	}
 
 	/* fan4 and fan5 share some pins with the GPIO and serial flash */
 
-	superio_enter();
-	fan5pin = superio_inb(0x24) & 0x2;
-	fan4pin = superio_inb(0x29) & 0x6;
-	superio_exit();
+	fan5pin = superio_inb(sio_data->sioreg, 0x24) & 0x2;
+	fan4pin = superio_inb(sio_data->sioreg, 0x29) & 0x6;
+	superio_exit(sio_data->sioreg);
 
 	/* It looks like fan4 and fan5 pins can be alternatively used
 	   as fan on/off switches, but fan5 control is write only :/
@@ -1248,7 +1306,7 @@
 	   is not the default. */
 
 	data->has_fan = 0x07; /* fan1, fan2 and fan3 */
-	i = w83627ehf_read_value(client, W83627EHF_REG_FANDIV1);
+	i = w83627ehf_read_value(data, W83627EHF_REG_FANDIV1);
 	if ((i & (1 << 2)) && (!fan4pin))
 		data->has_fan |= (1 << 3);
 	if (!(i & (1 << 1)) && (!fan5pin))
@@ -1268,7 +1326,7 @@
 				goto exit_remove;
 		}
 
-	for (i = 0; i < w83627ehf_num_in; i++)
+	for (i = 0; i < data->in_num; i++)
 		if ((err = device_create_file(dev, &sda_in_input[i].dev_attr))
 			|| (err = device_create_file(dev,
 				&sda_in_alarm[i].dev_attr))
@@ -1308,6 +1366,16 @@
 		if ((err = device_create_file(dev, &sda_temp[i].dev_attr)))
 			goto exit_remove;
 
+	err = device_create_file(dev, &dev_attr_name);
+	if (err)
+		goto exit_remove;
+
+	if (data->vid != 0x3f) {
+		err = device_create_file(dev, &dev_attr_cpu0_vid);
+		if (err)
+			goto exit_remove;
+	}
+
 	data->class_dev = hwmon_device_register(dev);
 	if (IS_ERR(data->class_dev)) {
 		err = PTR_ERR(data->class_dev);
@@ -1318,95 +1386,172 @@
 
 exit_remove:
 	w83627ehf_device_remove_files(dev);
-	i2c_detach_client(client);
-exit_free:
 	kfree(data);
+	platform_set_drvdata(pdev, NULL);
 exit_release:
-	release_region(address + IOREGION_OFFSET, IOREGION_LENGTH);
+	release_region(res->start, IOREGION_LENGTH);
 exit:
 	return err;
 }
 
-static int w83627ehf_detach_client(struct i2c_client *client)
+static int __devexit w83627ehf_remove(struct platform_device *pdev)
 {
-	struct w83627ehf_data *data = i2c_get_clientdata(client);
-	int err;
+	struct w83627ehf_data *data = platform_get_drvdata(pdev);
 
 	hwmon_device_unregister(data->class_dev);
-	w83627ehf_device_remove_files(&client->dev);
-
-	if ((err = i2c_detach_client(client)))
-		return err;
-	release_region(client->addr + IOREGION_OFFSET, IOREGION_LENGTH);
+	w83627ehf_device_remove_files(&pdev->dev);
+	release_region(data->addr, IOREGION_LENGTH);
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 
 	return 0;
 }
 
-static struct i2c_driver w83627ehf_driver = {
+static struct platform_driver w83627ehf_driver = {
 	.driver = {
 		.owner	= THIS_MODULE,
-		.name	= "w83627ehf",
+		.name	= DRVNAME,
 	},
-	.attach_adapter	= w83627ehf_detect,
-	.detach_client	= w83627ehf_detach_client,
+	.probe		= w83627ehf_probe,
+	.remove		= __devexit_p(w83627ehf_remove),
 };
 
-static int __init w83627ehf_find(int sioaddr, unsigned short *addr)
+/* w83627ehf_find() looks for a '627 in the Super-I/O config space */
+static int __init w83627ehf_find(int sioaddr, unsigned short *addr,
+				 struct w83627ehf_sio_data *sio_data)
 {
+	static const char __initdata sio_name_W83627EHF[] = "W83627EHF";
+	static const char __initdata sio_name_W83627EHG[] = "W83627EHG";
+	static const char __initdata sio_name_W83627DHG[] = "W83627DHG";
+
 	u16 val;
+	const char *sio_name;
 
-	REG = sioaddr;
-	VAL = sioaddr + 1;
-	superio_enter();
+	superio_enter(sioaddr);
 
-	val = (superio_inb(SIO_REG_DEVID) << 8)
-	    | superio_inb(SIO_REG_DEVID + 1);
+	val = (superio_inb(sioaddr, SIO_REG_DEVID) << 8)
+	    | superio_inb(sioaddr, SIO_REG_DEVID + 1);
 	switch (val & SIO_ID_MASK) {
-	case SIO_W83627DHG_ID:
-		w83627ehf_num_in = 9;
-		break;
 	case SIO_W83627EHF_ID:
+		sio_data->kind = w83627ehf;
+		sio_name = sio_name_W83627EHF;
+		break;
 	case SIO_W83627EHG_ID:
-		w83627ehf_num_in = 10;
+		sio_data->kind = w83627ehf;
+		sio_name = sio_name_W83627EHG;
+		break;
+	case SIO_W83627DHG_ID:
+		sio_data->kind = w83627dhg;
+		sio_name = sio_name_W83627DHG;
 		break;
 	default:
-		printk(KERN_WARNING "w83627ehf: unsupported chip ID: 0x%04x\n",
-			val);
-		superio_exit();
+		if (val != 0xffff)
+			pr_debug(DRVNAME ": unsupported chip ID: 0x%04x\n",
+				 val);
+		superio_exit(sioaddr);
 		return -ENODEV;
 	}
 
-	superio_select(W83627EHF_LD_HWM);
-	val = (superio_inb(SIO_REG_ADDR) << 8)
-	    | superio_inb(SIO_REG_ADDR + 1);
+	/* We have a known chip, find the HWM I/O address */
+	superio_select(sioaddr, W83627EHF_LD_HWM);
+	val = (superio_inb(sioaddr, SIO_REG_ADDR) << 8)
+	    | superio_inb(sioaddr, SIO_REG_ADDR + 1);
 	*addr = val & IOREGION_ALIGNMENT;
 	if (*addr == 0) {
-		superio_exit();
+		printk(KERN_ERR DRVNAME ": Refusing to enable a Super-I/O "
+		       "device with a base I/O port 0.\n");
+		superio_exit(sioaddr);
 		return -ENODEV;
 	}
 
 	/* Activate logical device if needed */
-	val = superio_inb(SIO_REG_ENABLE);
-	if (!(val & 0x01))
-		superio_outb(SIO_REG_ENABLE, val | 0x01);
+	val = superio_inb(sioaddr, SIO_REG_ENABLE);
+	if (!(val & 0x01)) {
+		printk(KERN_WARNING DRVNAME ": Forcibly enabling Super-I/O. "
+		       "Sensor is probably unusable.\n");
+		superio_outb(sioaddr, SIO_REG_ENABLE, val | 0x01);
+	}
 
-	superio_exit();
+	superio_exit(sioaddr);
+	pr_info(DRVNAME ": Found %s chip at %#x\n", sio_name, *addr);
+	sio_data->sioreg = sioaddr;
+
 	return 0;
 }
 
+/* when Super-I/O functions move to a separate file, the Super-I/O
+ * bus will manage the lifetime of the device and this module will only keep
+ * track of the w83627ehf driver. But since we platform_device_alloc(), we
+ * must keep track of the device */
+static struct platform_device *pdev;
+
 static int __init sensors_w83627ehf_init(void)
 {
-	if (w83627ehf_find(0x2e, &address)
-	 && w83627ehf_find(0x4e, &address))
+	int err;
+	unsigned short address;
+	struct resource res;
+	struct w83627ehf_sio_data sio_data;
+
+	/* initialize sio_data->kind and sio_data->sioreg.
+	 *
+	 * when Super-I/O functions move to a separate file, the Super-I/O
+	 * driver will probe 0x2e and 0x4e and auto-detect the presence of a
+	 * w83627ehf hardware monitor, and call probe() */
+	if (w83627ehf_find(0x2e, &address, &sio_data) &&
+	    w83627ehf_find(0x4e, &address, &sio_data))
 		return -ENODEV;
 
-	return i2c_isa_add_driver(&w83627ehf_driver);
+	err = platform_driver_register(&w83627ehf_driver);
+	if (err)
+		goto exit;
+
+	if (!(pdev = platform_device_alloc(DRVNAME, address))) {
+		err = -ENOMEM;
+		printk(KERN_ERR DRVNAME ": Device allocation failed\n");
+		goto exit_unregister;
+	}
+
+	err = platform_device_add_data(pdev, &sio_data,
+				       sizeof(struct w83627ehf_sio_data));
+	if (err) {
+		printk(KERN_ERR DRVNAME ": Platform data allocation failed\n");
+		goto exit_device_put;
+	}
+
+	memset(&res, 0, sizeof(res));
+	res.name = DRVNAME;
+	res.start = address + IOREGION_OFFSET;
+	res.end = address + IOREGION_OFFSET + IOREGION_LENGTH - 1;
+	res.flags = IORESOURCE_IO;
+	err = platform_device_add_resources(pdev, &res, 1);
+	if (err) {
+		printk(KERN_ERR DRVNAME ": Device resource addition failed "
+		       "(%d)\n", err);
+		goto exit_device_put;
+	}
+
+	/* platform_device_add calls probe() */
+	err = platform_device_add(pdev);
+	if (err) {
+		printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
+		       err);
+		goto exit_device_put;
+	}
+
+	return 0;
+
+exit_device_put:
+	platform_device_put(pdev);
+exit_unregister:
+	platform_driver_unregister(&w83627ehf_driver);
+exit:
+	return err;
 }
 
 static void __exit sensors_w83627ehf_exit(void)
 {
-	i2c_isa_del_driver(&w83627ehf_driver);
+	platform_device_unregister(pdev);
+	platform_driver_unregister(&w83627ehf_driver);
 }
 
 MODULE_AUTHOR("Jean Delvare <khali@linux-fr.org>");
diff --git a/drivers/hwmon/w83627hf.c b/drivers/hwmon/w83627hf.c
index 12cb40a..1ce7817 100644
--- a/drivers/hwmon/w83627hf.c
+++ b/drivers/hwmon/w83627hf.c
@@ -220,6 +220,18 @@
 #define W836X7HF_REG_PWM(type, nr) (((type) == w83627hf) ? \
                                      regpwm_627hf[(nr) - 1] : regpwm[(nr) - 1])
 
+#define W83627HF_REG_PWM_FREQ		0x5C	/* Only for the 627HF */
+
+#define W83637HF_REG_PWM_FREQ1		0x00	/* 697HF/687THF too */
+#define W83637HF_REG_PWM_FREQ2		0x02	/* 697HF/687THF too */
+#define W83637HF_REG_PWM_FREQ3		0x10	/* 687THF too */
+
+static const u8 W83637HF_REG_PWM_FREQ[] = { W83637HF_REG_PWM_FREQ1,
+					W83637HF_REG_PWM_FREQ2,
+					W83637HF_REG_PWM_FREQ3 };
+
+#define W83627HF_BASE_PWM_FREQ	46870
+
 #define W83781D_REG_I2C_ADDR 0x48
 #define W83781D_REG_I2C_SUBADDR 0x4A
 
@@ -267,6 +279,49 @@
 
 #define PWM_TO_REG(val) (SENSORS_LIMIT((val),0,255))
 
+static inline unsigned long pwm_freq_from_reg_627hf(u8 reg)
+{
+	unsigned long freq;
+	freq = W83627HF_BASE_PWM_FREQ >> reg;
+	return freq;
+}
+static inline u8 pwm_freq_to_reg_627hf(unsigned long val)
+{
+	u8 i;
+	/* Only 5 dividers (1 2 4 8 16)
+	   Search for the nearest available frequency */
+	for (i = 0; i < 4; i++) {
+		if (val > (((W83627HF_BASE_PWM_FREQ >> i) +
+			    (W83627HF_BASE_PWM_FREQ >> (i+1))) / 2))
+			break;
+	}
+	return i;
+}
+
+static inline unsigned long pwm_freq_from_reg(u8 reg)
+{
+	/* Clock bit 8 -> 180 kHz or 24 MHz */
+	unsigned long clock = (reg & 0x80) ? 180000UL : 24000000UL;
+
+	reg &= 0x7f;
+	/* This should not happen but anyway... */
+	if (reg == 0)
+		reg++;
+	return (clock / (reg << 8));
+}
+static inline u8 pwm_freq_to_reg(unsigned long val)
+{
+	/* Minimum divider value is 0x01 and maximum is 0x7F */
+	if (val >= 93750)	/* The highest we can do */
+		return 0x01;
+	if (val >= 720)	/* Use 24 MHz clock */
+		return (24000000UL / (val << 8));
+	if (val < 6)		/* The lowest we can do */
+		return 0xFF;
+	else			/* Use 180 kHz clock */
+		return (0x80 | (180000UL / (val << 8)));
+}
+
 #define BEEP_MASK_FROM_REG(val)		 (val)
 #define BEEP_MASK_TO_REG(val)		((val) & 0xffffff)
 #define BEEP_ENABLE_TO_REG(val)		((val)?1:0)
@@ -316,6 +371,7 @@
 	u32 beep_mask;		/* Register encoding, combined */
 	u8 beep_enable;		/* Boolean */
 	u8 pwm[3];		/* Register value */
+	u8 pwm_freq[3];		/* Register value */
 	u16 sens[3];		/* 782D/783S only.
 				   1 = pentium diode; 2 = 3904 diode;
 				   3000-5000 = thermistor beta.
@@ -852,6 +908,64 @@
 sysfs_pwm(3);
 
 static ssize_t
+show_pwm_freq_reg(struct device *dev, char *buf, int nr)
+{
+	struct w83627hf_data *data = w83627hf_update_device(dev);
+	if (data->type == w83627hf)
+		return sprintf(buf, "%ld\n",
+			pwm_freq_from_reg_627hf(data->pwm_freq[nr - 1]));
+	else
+		return sprintf(buf, "%ld\n",
+			pwm_freq_from_reg(data->pwm_freq[nr - 1]));
+}
+
+static ssize_t
+store_pwm_freq_reg(struct device *dev, const char *buf, size_t count, int nr)
+{
+	struct w83627hf_data *data = dev_get_drvdata(dev);
+	static const u8 mask[]={0xF8, 0x8F};
+	u32 val;
+
+	val = simple_strtoul(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+
+	if (data->type == w83627hf) {
+		data->pwm_freq[nr - 1] = pwm_freq_to_reg_627hf(val);
+		w83627hf_write_value(data, W83627HF_REG_PWM_FREQ,
+				(data->pwm_freq[nr - 1] << ((nr - 1)*4)) |
+				(w83627hf_read_value(data,
+				W83627HF_REG_PWM_FREQ) & mask[nr - 1]));
+	} else {
+		data->pwm_freq[nr - 1] = pwm_freq_to_reg(val);
+		w83627hf_write_value(data, W83637HF_REG_PWM_FREQ[nr - 1],
+				data->pwm_freq[nr - 1]);
+	}
+
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+#define sysfs_pwm_freq(offset) \
+static ssize_t show_regs_pwm_freq_##offset(struct device *dev, \
+		struct device_attribute *attr, char *buf) \
+{ \
+	return show_pwm_freq_reg(dev, buf, offset); \
+} \
+static ssize_t \
+store_regs_pwm_freq_##offset(struct device *dev, \
+		struct device_attribute *attr, const char *buf, size_t count) \
+{ \
+	return store_pwm_freq_reg(dev, buf, count, offset); \
+} \
+static DEVICE_ATTR(pwm##offset##_freq, S_IRUGO | S_IWUSR, \
+		  show_regs_pwm_freq_##offset, store_regs_pwm_freq_##offset);
+
+sysfs_pwm_freq(1);
+sysfs_pwm_freq(2);
+sysfs_pwm_freq(3);
+
+static ssize_t
 show_sensor_reg(struct device *dev, char *buf, int nr)
 {
 	struct w83627hf_data *data = w83627hf_update_device(dev);
@@ -1077,6 +1191,9 @@
 
 	&dev_attr_pwm3.attr,
 
+	&dev_attr_pwm1_freq.attr,
+	&dev_attr_pwm2_freq.attr,
+	&dev_attr_pwm3_freq.attr,
 	NULL
 };
 
@@ -1139,7 +1256,9 @@
 		 || (err = device_create_file(dev, &dev_attr_in5_max))
 		 || (err = device_create_file(dev, &dev_attr_in6_input))
 		 || (err = device_create_file(dev, &dev_attr_in6_min))
-		 || (err = device_create_file(dev, &dev_attr_in6_max)))
+		 || (err = device_create_file(dev, &dev_attr_in6_max))
+		 || (err = device_create_file(dev, &dev_attr_pwm1_freq))
+		 || (err = device_create_file(dev, &dev_attr_pwm2_freq)))
 			goto ERROR4;
 
 	if (data->type != w83697hf)
@@ -1169,6 +1288,12 @@
 		if ((err = device_create_file(dev, &dev_attr_pwm3)))
 			goto ERROR4;
 
+	if (data->type == w83637hf || data->type == w83687thf)
+		if ((err = device_create_file(dev, &dev_attr_pwm1_freq))
+		 || (err = device_create_file(dev, &dev_attr_pwm2_freq))
+		 || (err = device_create_file(dev, &dev_attr_pwm3_freq)))
+			goto ERROR4;
+
 	data->class_dev = hwmon_device_register(dev);
 	if (IS_ERR(data->class_dev)) {
 		err = PTR_ERR(data->class_dev);
@@ -1181,6 +1306,7 @@
 	sysfs_remove_group(&dev->kobj, &w83627hf_group);
 	sysfs_remove_group(&dev->kobj, &w83627hf_group_opt);
       ERROR3:
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
       ERROR1:
 	release_region(res->start, WINB_REGION_SIZE);
@@ -1193,11 +1319,11 @@
 	struct w83627hf_data *data = platform_get_drvdata(pdev);
 	struct resource *res;
 
-	platform_set_drvdata(pdev, NULL);
 	hwmon_device_unregister(data->class_dev);
 
 	sysfs_remove_group(&pdev->dev.kobj, &w83627hf_group);
 	sysfs_remove_group(&pdev->dev.kobj, &w83627hf_group_opt);
+	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 
 	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
@@ -1472,6 +1598,20 @@
 			   (data->type == w83627hf || data->type == w83697hf))
 				break;
 		}
+		if (data->type == w83627hf) {
+				u8 tmp = w83627hf_read_value(data,
+						W83627HF_REG_PWM_FREQ);
+				data->pwm_freq[0] = tmp & 0x07;
+				data->pwm_freq[1] = (tmp >> 4) & 0x07;
+		} else if (data->type != w83627thf) {
+			for (i = 1; i <= 3; i++) {
+				data->pwm_freq[i - 1] =
+					w83627hf_read_value(data,
+						W83637HF_REG_PWM_FREQ[i - 1]);
+				if (i == 2 && (data->type == w83697hf))
+					break;
+			}
+		}
 
 		data->temp = w83627hf_read_value(data, W83781D_REG_TEMP(1));
 		data->temp_max =
@@ -1548,15 +1688,12 @@
 		goto exit_device_put;
 	}
 
-	pdev->dev.platform_data = kmalloc(sizeof(struct w83627hf_sio_data),
-					  GFP_KERNEL);
-	if (!pdev->dev.platform_data) {
-		err = -ENOMEM;
+	err = platform_device_add_data(pdev, sio_data,
+				       sizeof(struct w83627hf_sio_data));
+	if (err) {
 		printk(KERN_ERR DRVNAME ": Platform data allocation failed\n");
 		goto exit_device_put;
 	}
-	memcpy(pdev->dev.platform_data, sio_data,
-	       sizeof(struct w83627hf_sio_data));
 
 	err = platform_device_add(pdev);
 	if (err) {
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 1c77e14..da16478 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -237,9 +237,6 @@
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-iop3xx.
 
-config I2C_ISA
-	tristate
-
 config I2C_IXP4XX
 	tristate "IXP4xx GPIO-Based I2C Interface (DEPRECATED)"
 	depends on ARCH_IXP4XX
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index a6db4e3..5b752e4 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -18,7 +18,6 @@
 obj-$(CONFIG_I2C_I810)		+= i2c-i810.o
 obj-$(CONFIG_I2C_IBM_IIC)	+= i2c-ibm_iic.o
 obj-$(CONFIG_I2C_IOP3XX)	+= i2c-iop3xx.o
-obj-$(CONFIG_I2C_ISA)		+= i2c-isa.o
 obj-$(CONFIG_I2C_IXP2000)	+= i2c-ixp2000.o
 obj-$(CONFIG_I2C_IXP4XX)	+= i2c-ixp4xx.o
 obj-$(CONFIG_I2C_POWERMAC)	+= i2c-powermac.o
diff --git a/drivers/i2c/busses/i2c-isa.c b/drivers/i2c/busses/i2c-isa.c
deleted file mode 100644
index b0e1370..0000000
--- a/drivers/i2c/busses/i2c-isa.c
+++ /dev/null
@@ -1,192 +0,0 @@
-/*
-    i2c-isa.c - an i2c-core-like thing for ISA hardware monitoring chips
-    Copyright (C) 2005  Jean Delvare <khali@linux-fr.org>
-
-    Based on the i2c-isa pseudo-adapter from the lm_sensors project
-    Copyright (c) 1998, 1999  Frodo Looijaard <frodol@dds.nl> 
-
-    This program is free software; you can redistribute it and/or modify
-    it under the terms of the GNU General Public License as published by
-    the Free Software Foundation; either version 2 of the License, or
-    (at your option) any later version.
-
-    This program is distributed in the hope that it will be useful,
-    but WITHOUT ANY WARRANTY; without even the implied warranty of
-    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-    GNU General Public License for more details.
-
-    You should have received a copy of the GNU General Public License
-    along with this program; if not, write to the Free Software
-    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
-*/
-
-/* This implements an i2c-core-like thing for ISA hardware monitoring
-   chips. Such chips are linked to the i2c subsystem for historical
-   reasons (because the early ISA hardware monitoring chips such as the
-   LM78 had both an I2C and an ISA interface). They used to be
-   registered with the main i2c-core, but as a first step in the
-   direction of a clean separation between I2C and ISA chip drivers,
-   we now have this separate core for ISA ones. It is significantly
-   more simple than the real one, of course, because we don't have to
-   handle multiple busses: there is only one (fake) ISA adapter.
-   It is worth noting that we still rely on i2c-core for some things
-   at the moment - but hopefully this won't last. */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/i2c.h>
-#include <linux/i2c-isa.h>
-#include <linux/platform_device.h>
-#include <linux/completion.h>
-
-/* Exported by i2c-core for i2c-isa only */
-extern void i2c_adapter_dev_release(struct device *dev);
-extern struct class i2c_adapter_class;
-
-static u32 isa_func(struct i2c_adapter *adapter);
-
-/* This is the actual algorithm we define */
-static const struct i2c_algorithm isa_algorithm = {
-	.functionality	= isa_func,
-};
-
-/* There can only be one... */
-static struct i2c_adapter isa_adapter = {
-	.owner		= THIS_MODULE,
-	.id		= I2C_HW_ISA,
-	.class          = I2C_CLASS_HWMON,
-	.algo		= &isa_algorithm,
-	.name		= "ISA main adapter",
-};
-
-/* We can't do a thing... */
-static u32 isa_func(struct i2c_adapter *adapter)
-{
-	return 0;
-}
-
-
-/* We implement an interface which resembles i2c_{add,del}_driver,
-   but for i2c-isa drivers. We don't have to remember and handle lists
-   of drivers and adapters so this is much more simple, of course. */
-
-int i2c_isa_add_driver(struct i2c_driver *driver)
-{
-	int res;
-
-	/* Add the driver to the list of i2c drivers in the driver core */
-	driver->driver.bus = &i2c_bus_type;
-	res = driver_register(&driver->driver);
-	if (res)
-		return res;
-	dev_dbg(&isa_adapter.dev, "Driver %s registered\n", driver->driver.name);
-
-	/* Now look for clients */
-	res = driver->attach_adapter(&isa_adapter);
-	if (res) {
-		dev_dbg(&isa_adapter.dev,
-			"Driver %s failed to attach adapter, unregistering\n",
-			driver->driver.name);
-		driver_unregister(&driver->driver);
-	}
-	return res;
-}
-
-int i2c_isa_del_driver(struct i2c_driver *driver)
-{
-	struct list_head *item, *_n;
-	struct i2c_client *client;
-	int res;
-
-	/* Detach all clients belonging to this one driver */
-	list_for_each_safe(item, _n, &isa_adapter.clients) {
-		client = list_entry(item, struct i2c_client, list);
-		if (client->driver != driver)
-			continue;
-		dev_dbg(&isa_adapter.dev, "Detaching client %s at 0x%x\n",
-			client->name, client->addr);
-		if ((res = driver->detach_client(client))) {
-			dev_err(&isa_adapter.dev, "Failed, driver "
-				"%s not unregistered!\n",
-				driver->driver.name);
-			return res;
-		}
-	}
-
-	/* Get the driver off the core list */
-	driver_unregister(&driver->driver);
-	dev_dbg(&isa_adapter.dev, "Driver %s unregistered\n", driver->driver.name);
-
-	return 0;
-}
-
-
-static int __init i2c_isa_init(void)
-{
-	int err;
-
-	mutex_init(&isa_adapter.clist_lock);
-	INIT_LIST_HEAD(&isa_adapter.clients);
-
-	isa_adapter.nr = ANY_I2C_ISA_BUS;
-	isa_adapter.dev.parent = &platform_bus;
-	sprintf(isa_adapter.dev.bus_id, "i2c-%d", isa_adapter.nr);
-	isa_adapter.dev.release = &i2c_adapter_dev_release;
-	isa_adapter.dev.class = &i2c_adapter_class;
-	err = device_register(&isa_adapter.dev);
-	if (err) {
-		printk(KERN_ERR "i2c-isa: Failed to register device\n");
-		goto exit;
-	}
-
-	dev_dbg(&isa_adapter.dev, "%s registered\n", isa_adapter.name);
-
-	return 0;
-
-exit:
-	return err;
-}
-
-static void __exit i2c_isa_exit(void)
-{
-#ifdef DEBUG
-	struct list_head  *item, *_n;
-	struct i2c_client *client = NULL;
-#endif
-
-	/* There should be no more active client */
-#ifdef DEBUG
-	dev_dbg(&isa_adapter.dev, "Looking for clients\n");
-	list_for_each_safe(item, _n, &isa_adapter.clients) {
-		client = list_entry(item, struct i2c_client, list);
-		dev_err(&isa_adapter.dev, "Driver %s still has an active "
-			"ISA client at 0x%x\n", client->driver->driver.name,
-			client->addr);
-	}
-	if (client != NULL)
-		return;
-#endif
-
-	/* Clean up the sysfs representation */
-	dev_dbg(&isa_adapter.dev, "Unregistering from sysfs\n");
-	init_completion(&isa_adapter.dev_released);
-	device_unregister(&isa_adapter.dev);
-
-	/* Wait for sysfs to drop all references */
-	dev_dbg(&isa_adapter.dev, "Waiting for sysfs completion\n");
-	wait_for_completion(&isa_adapter.dev_released);
-
-	dev_dbg(&isa_adapter.dev, "%s unregistered\n", isa_adapter.name);
-}
-
-EXPORT_SYMBOL(i2c_isa_add_driver);
-EXPORT_SYMBOL(i2c_isa_del_driver);
-
-MODULE_AUTHOR("Jean Delvare <khali@linux-fr.org>");
-MODULE_DESCRIPTION("ISA bus access through i2c");
-MODULE_LICENSE("GPL");
-
-module_init(i2c_isa_init);
-module_exit(i2c_isa_exit);
diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c
index 6971a62..d663e69 100644
--- a/drivers/i2c/i2c-core.c
+++ b/drivers/i2c/i2c-core.c
@@ -288,7 +288,6 @@
 	struct i2c_adapter *adap = to_i2c_adapter(dev);
 	complete(&adap->dev_released);
 }
-EXPORT_SYMBOL_GPL(i2c_adapter_dev_release);	/* exported to i2c-isa */
 
 static ssize_t
 show_adapter_name(struct device *dev, struct device_attribute *attr, char *buf)
@@ -307,7 +306,6 @@
 	.name			= "i2c-adapter",
 	.dev_attrs		= i2c_adapter_attrs,
 };
-EXPORT_SYMBOL_GPL(i2c_adapter_class);		/* exported to i2c-isa */
 
 static void i2c_scan_static_board_info(struct i2c_adapter *adapter)
 {
diff --git a/include/linux/i2c-isa.h b/include/linux/i2c-isa.h
deleted file mode 100644
index 67e3598..0000000
--- a/include/linux/i2c-isa.h
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * i2c-isa.h - definitions for the i2c-isa pseudo-i2c-adapter interface
- *
- * Copyright (C) 2005 Jean Delvare <khali@linux-fr.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#ifndef _LINUX_I2C_ISA_H
-#define _LINUX_I2C_ISA_H
-
-#include <linux/i2c.h>
-
-extern int i2c_isa_add_driver(struct i2c_driver *driver);
-extern int i2c_isa_del_driver(struct i2c_driver *driver);
-
-/* Detect whether we are on the isa bus. This is only useful to hybrid
-   (i2c+isa) drivers. */
-#define i2c_is_isa_adapter(adapptr) \
-        ((adapptr)->id == I2C_HW_ISA)
-#define i2c_is_isa_client(clientptr) \
-        i2c_is_isa_adapter((clientptr)->adapter)
-
-#endif /* _LINUX_I2C_ISA_H */
diff --git a/include/linux/i2c.h b/include/linux/i2c.h
index 2eaba21..0c37a73 100644
--- a/include/linux/i2c.h
+++ b/include/linux/i2c.h
@@ -368,7 +368,6 @@
 
 /* The numbers to use to set I2C bus address */
 #define ANY_I2C_BUS		0xffff
-#define ANY_I2C_ISA_BUS		9191
 
 
 /* ----- functions exported by i2c.o */