diff --git a/Documentation/ABI/testing/sysfs-class-power b/Documentation/ABI/testing/sysfs-class-power
index 369d2a2..fa05719 100644
--- a/Documentation/ABI/testing/sysfs-class-power
+++ b/Documentation/ABI/testing/sysfs-class-power
@@ -74,3 +74,61 @@
 
 		Valid values:
 		- 0 - 70 (minutes), step by 10 (rounded down)
+
+What:		/sys/class/power_supply/bq24257-charger/ovp_voltage
+Date:		October 2015
+KernelVersion:	4.4.0
+Contact:	Andreas Dannenberg <dannenberg@ti.com>
+Description:
+		This entry configures the overvoltage protection feature of bq24257-
+		type charger devices. This feature protects the device and other
+		components against damage from overvoltage on the input supply. See
+		device datasheet for details.
+
+		Valid values:
+		- 6000000, 6500000, 7000000, 8000000, 9000000, 9500000, 10000000,
+		  10500000 (all uV)
+
+What:		/sys/class/power_supply/bq24257-charger/in_dpm_voltage
+Date:		October 2015
+KernelVersion:	4.4.0
+Contact:	Andreas Dannenberg <dannenberg@ti.com>
+Description:
+		This entry configures the input dynamic power path management voltage of
+		bq24257-type charger devices. Once the supply drops to the configured
+		voltage, the input current limit is reduced down to prevent the further
+		drop of the supply. When the IC enters this mode, the charge current is
+		lower than the set value. See device datasheet for details.
+
+		Valid values:
+		- 4200000, 4280000, 4360000, 4440000, 4520000, 4600000, 4680000,
+		  4760000 (all uV)
+
+What:		/sys/class/power_supply/bq24257-charger/high_impedance_enable
+Date:		October 2015
+KernelVersion:	4.4.0
+Contact:	Andreas Dannenberg <dannenberg@ti.com>
+Description:
+		This entry allows enabling the high-impedance mode of bq24257-type
+		charger devices. If enabled, it places the charger IC into low power
+		standby mode with the switch mode controller disabled. When disabled,
+		the charger operates normally. See device datasheet for details.
+
+		Valid values:
+		- 1: enabled
+		- 0: disabled
+
+What:		/sys/class/power_supply/bq24257-charger/sysoff_enable
+Date:		October 2015
+KernelVersion:	4.4.0
+Contact:	Andreas Dannenberg <dannenberg@ti.com>
+Description:
+		This entry allows enabling the sysoff mode of bq24257-type charger
+		devices. If enabled and the input is removed, the internal battery FET
+		is turned off in order to reduce the leakage from the BAT pin to less
+		than 1uA. Note that on some devices/systems this disconnects the battery
+		from the system. See device datasheet for details.
+
+		Valid values:
+		- 1: enabled
+		- 0: disabled
diff --git a/Documentation/devicetree/bindings/power/bq24257.txt b/Documentation/devicetree/bindings/power/bq24257.txt
index 5c9d394..d693702 100644
--- a/Documentation/devicetree/bindings/power/bq24257.txt
+++ b/Documentation/devicetree/bindings/power/bq24257.txt
@@ -1,21 +1,64 @@
-Binding for TI bq24257 Li-Ion Charger
+Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger
 
 Required properties:
 - compatible: Should contain one of the following:
+ * "ti,bq24250"
+ * "ti,bq24251"
  * "ti,bq24257"
-- reg:			   integer, i2c address of the device.
+- reg: integer, i2c address of the device.
+- interrupt-parent: Should be the phandle for the interrupt controller. Use in
+    conjunction with "interrupts".
+- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in
+    conjunction with "interrupt-parent".
 - ti,battery-regulation-voltage: integer, maximum charging voltage in uV.
-- ti,charge-current:	   integer, maximum charging current in uA.
-- ti,termination-current:  integer, charge will be terminated when current in
-			   constant-voltage phase drops below this value (in uA).
+- ti,charge-current: integer, maximum charging current in uA.
+- ti,termination-current: integer, charge will be terminated when current in
+    constant-voltage phase drops below this value (in uA).
+
+Optional properties:
+- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin.
+    This pin is not available on all devices however it should be used if
+    possible as this is the recommended way to obtain the charger's input PG
+    state. If this pin is not specified a software-based approach for PG
+    detection is used.
+- ti,current-limit: The maximum current to be drawn from the charger's input
+    (in uA). If this property is not specified, the input limit current is
+    set automatically using USB D+/D- signal based charger type detection.
+    If the hardware does not support the D+/D- based detection, a default
+    of 500,000 is used (=500mA) instead.
+- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If
+    not specified a default of 6,5000,000 (=6.5V) is used.
+- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic
+    power path management (in uV). If not specified a default of 4,360,000
+    (=4.36V) is used.
 
 Example:
 
 bq24257 {
 	compatible = "ti,bq24257";
 	reg = <0x6a>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+	pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
 
 	ti,battery-regulation-voltage = <4200000>;
 	ti,charge-current = <1000000>;
 	ti,termination-current = <50000>;
 };
+
+Example:
+
+bq24250 {
+	compatible = "ti,bq24250";
+	reg = <0x6a>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+	ti,battery-regulation-voltage = <4200000>;
+	ti,charge-current = <500000>;
+	ti,termination-current = <50000>;
+	ti,current-limit = <900000>;
+	ti,ovp-voltage = <9500000>;
+	ti,in-dpm-voltage = <4440000>;
+};
diff --git a/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt b/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt
new file mode 100644
index 0000000..862f4a4
--- /dev/null
+++ b/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt
@@ -0,0 +1,34 @@
+AXP20x USB power supply
+
+Required Properties:
+-compatible: "x-powers,axp202-usb-power-supply"
+
+This node is a subnode of the axp20x PMIC.
+
+Example:
+
+axp209: pmic@34 {
+	compatible = "x-powers,axp209";
+	reg = <0x34>;
+	interrupt-parent = <&nmi_intc>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	interrupt-controller;
+	#interrupt-cells = <1>;
+
+	regulators {
+		x-powers,dcdc-freq = <1500>;
+
+		vdd_cpu: dcdc2 {
+			regulator-always-on;
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1450000>;
+			regulator-name = "vdd-cpu";
+		};
+
+		...
+	};
+
+	usb-power-supply: usb-power-supply {
+		compatible = "x-powers,axp202-usb-power-supply";
+	};
+};
diff --git a/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt
new file mode 100644
index 0000000..65b88fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt
@@ -0,0 +1,131 @@
+Qualcomm Switch-Mode Battery Charger and Boost
+
+PROPERTIES
+- compatible:
+  Usage: required
+  Value type: <stringlist>
+  Description: Must be one of:
+               - "qcom,pm8941-charger"
+
+- reg:
+  Usage: required
+  Value type: <prop-encoded-array>
+  Description: Base address of registers for SMBB block
+
+- interrupts:
+  Usage: required
+  Value type: <prop-encoded-array>
+  Description: The format of the specifier is defined by the binding document
+               describing the node's interrupt parent.  Must contain one
+               specifier for each of the following interrupts, in order:
+               - charge done
+               - charge fast mode
+               - charge trickle mode
+               - battery temperature ok
+               - battery present
+               - charger disconnected
+               - USB-in valid
+               - DC-in valid
+
+- interrupt-names:
+  Usage: required
+  Value type: <stringlist>
+  Description: Must contain the following list, strictly ordered:
+               "chg-done",
+               "chg-fast",
+               "chg-trkl",
+               "bat-temp-ok",
+               "bat-present",
+               "chg-gone",
+               "usb-valid",
+               "dc-valid"
+
+- qcom,fast-charge-current-limit:
+  Usage: optional (default: 1A, or pre-configured value)
+  Value type: <u32>; uA; range [100mA : 3A]
+  Description: Maximum charge current; May be clamped to safety limits.
+
+- qcom,fast-charge-low-threshold-voltage:
+  Usage: optional (default: 3.2V, or pre-configured value)
+  Value type: <u32>; uV; range [2.1V : 3.6V]
+  Description: Battery voltage limit above which fast charging may operate;
+               Below this value linear or switch-mode auto-trickle-charging
+               will operate.
+
+- qcom,fast-charge-high-threshold-voltage:
+  Usage: optional (default: 4.2V, or pre-configured value)
+  Value type: <u32>; uV; range [3.24V : 5V]
+  Description: Battery voltage limit below which fast charging may operate;
+               The fast charger will attempt to charge the battery to this
+               voltage.  May be clamped to safety limits.
+
+- qcom,fast-charge-safe-voltage:
+  Usage: optional (default: 4.2V, or pre-configured value)
+  Value type: <u32>; uV; range [3.24V : 5V]
+  Description: Maximum safe battery voltage; May be pre-set by bootloader, in
+               which case, setting this will harmlessly fail. The property
+               'fast-charge-high-watermark' will be clamped by this value.
+
+- qcom,fast-charge-safe-current:
+  Usage: optional (default: 1A, or pre-configured value)
+  Value type: <u32>; uA; range [100mA : 3A]
+  Description: Maximum safe battery charge current; May pre-set by bootloader,
+               in which case, setting this will harmlessly fail. The property
+               'qcom,fast-charge-current-limit' will be clamped by this value.
+
+- qcom,auto-recharge-threshold-voltage:
+  Usage: optional (default: 4.1V, or pre-configured value)
+  Value type: <u32>; uV; range [3.24V : 5V]
+  Description: Battery voltage limit below which auto-recharge functionality
+               will restart charging after end-of-charge;  The high cutoff
+               limit for auto-recharge is 5% above this value.
+
+- qcom,minimum-input-voltage:
+  Usage: optional (default: 4.3V, or pre-configured value)
+  Value type: <u32>; uV; range [4.2V : 9.6V]
+  Description: Input voltage level above which charging may operate
+
+- qcom,dc-current-limit:
+  Usage: optional (default: 100mA, or pre-configured value)
+  Value type: <u32>; uA; range [100mA : 2.5A]
+  Description: Default DC charge current limit
+
+- qcom,disable-dc:
+  Usage: optional (default: false)
+  Value type: boolean: <u32> or <empty>
+  Description: Disable DC charger
+
+- qcom,jeita-extended-temp-range:
+  Usage: optional (default: false)
+  Value type: boolean: <u32> or <empty>
+  Description: Enable JEITA extended temperature range;  This does *not*
+               adjust the maximum charge voltage or current in the extended
+               temperature range.  It only allows charging when the battery
+               is in the extended temperature range.  Voltage/current
+               regulation must be done externally to fully comply with
+               the JEITA safety guidelines if this flag is set.
+
+EXAMPLE
+charger@1000 {
+       compatible = "qcom,pm8941-charger";
+       reg = <0x1000 0x700>;
+       interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
+       interrupt-names = "chg-done",
+                       "chg-fast",
+                       "chg-trkl",
+                       "bat-temp-ok",
+                       "bat-present",
+                       "chg-gone",
+                       "usb-valid",
+                       "dc-valid";
+
+       qcom,fast-charge-current-limit = <1000000>;
+       qcom,dc-charge-current-limit = <1000000>;
+};
diff --git a/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt b/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt
new file mode 100644
index 0000000..98d131a
--- /dev/null
+++ b/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt
@@ -0,0 +1,12 @@
+TPS65217 Charger
+
+Required Properties:
+-compatible: "ti,tps65217-charger"
+
+This node is a subnode of the tps65217 PMIC.
+
+Example:
+
+	tps65217-charger {
+		compatible = "ti,tps65090-charger";
+	};
diff --git a/MAINTAINERS b/MAINTAINERS
index fe5ed80..283d602 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7505,10 +7505,10 @@
 M:	Pali Rohár <pali.rohar@gmail.com>
 S:	Maintained
 F:	include/linux/power/bq2415x_charger.h
-F:	include/linux/power/bq27x00_battery.h
+F:	include/linux/power/bq27xxx_battery.h
 F:	include/linux/power/isp1704_charger.h
 F:	drivers/power/bq2415x_charger.c
-F:	drivers/power/bq27x00_battery.c
+F:	drivers/power/bq27xxx_battery.c
 F:	drivers/power/isp1704_charger.c
 F:	drivers/power/rx51_battery.c
 
diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi
index 36ae916..482b7aa 100644
--- a/arch/arm/boot/dts/twl4030.dtsi
+++ b/arch/arm/boot/dts/twl4030.dtsi
@@ -22,6 +22,8 @@
 	charger: bci {
 		compatible = "ti,twl4030-bci";
 		interrupts = <9>, <2>;
+		io-channels = <&twl4030_madc 11>;
+		io-channel-name = "vac";
 		bci3v1-supply = <&vusb3v1>;
 	};
 
diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig
index 3f15a5c..c5e1943 100644
--- a/arch/arm/configs/omap2plus_defconfig
+++ b/arch/arm/configs/omap2plus_defconfig
@@ -246,7 +246,7 @@
 CONFIG_GPIO_PALMAS=y
 CONFIG_W1=m
 CONFIG_HDQ_MASTER_OMAP=m
-CONFIG_BATTERY_BQ27x00=m
+CONFIG_BATTERY_BQ27XXX=m
 CONFIG_CHARGER_ISP1704=m
 CONFIG_CHARGER_TWL4030=m
 CONFIG_CHARGER_BQ2415X=m
diff --git a/arch/unicore32/Kconfig b/arch/unicore32/Kconfig
index 928237a..c9faddc 100644
--- a/arch/unicore32/Kconfig
+++ b/arch/unicore32/Kconfig
@@ -222,7 +222,7 @@
 	tristate "I2C Battery BQ27200 Support"
 	select I2C_PUV3
 	select POWER_SUPPLY
-	select BATTERY_BQ27x00
+	select BATTERY_BQ27XXX
 
 config I2C_EEPROM_AT24
 	tristate "I2C EEPROMs AT24 support"
diff --git a/drivers/power/88pm860x_battery.c b/drivers/power/88pm860x_battery.c
index d49579b..63c57dc 100644
--- a/drivers/power/88pm860x_battery.c
+++ b/drivers/power/88pm860x_battery.c
@@ -954,47 +954,33 @@
 	else
 		info->resistor = 300;	/* set default internal resistor */
 
-	info->battery = power_supply_register(&pdev->dev, &pm860x_battery_desc,
-					      NULL);
+	info->battery = devm_power_supply_register(&pdev->dev,
+						   &pm860x_battery_desc,
+						   NULL);
 	if (IS_ERR(info->battery))
 		return PTR_ERR(info->battery);
 	info->battery->dev.parent = &pdev->dev;
 
-	ret = request_threaded_irq(info->irq_cc, NULL,
-				pm860x_coulomb_handler, IRQF_ONESHOT,
-				"coulomb", info);
+	ret = devm_request_threaded_irq(chip->dev, info->irq_cc, NULL,
+					pm860x_coulomb_handler, IRQF_ONESHOT,
+					"coulomb", info);
 	if (ret < 0) {
 		dev_err(chip->dev, "Failed to request IRQ: #%d: %d\n",
 			info->irq_cc, ret);
-		goto out_reg;
+		return ret;
 	}
 
-	ret = request_threaded_irq(info->irq_batt, NULL, pm860x_batt_handler,
-				IRQF_ONESHOT, "battery", info);
+	ret = devm_request_threaded_irq(chip->dev, info->irq_batt, NULL,
+					pm860x_batt_handler,
+					IRQF_ONESHOT, "battery", info);
 	if (ret < 0) {
 		dev_err(chip->dev, "Failed to request IRQ: #%d: %d\n",
 			info->irq_batt, ret);
-		goto out_coulomb;
+		return ret;
 	}
 
 
 	return 0;
-
-out_coulomb:
-	free_irq(info->irq_cc, info);
-out_reg:
-	power_supply_unregister(info->battery);
-	return ret;
-}
-
-static int pm860x_battery_remove(struct platform_device *pdev)
-{
-	struct pm860x_battery_info *info = platform_get_drvdata(pdev);
-
-	free_irq(info->irq_batt, info);
-	free_irq(info->irq_cc, info);
-	power_supply_unregister(info->battery);
-	return 0;
 }
 
 #ifdef CONFIG_PM_SLEEP
@@ -1028,7 +1014,6 @@
 		   .pm = &pm860x_battery_pm_ops,
 	},
 	.probe = pm860x_battery_probe,
-	.remove = pm860x_battery_remove,
 };
 module_platform_driver(pm860x_battery_driver);
 
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index f8758d6..02b3b31 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -157,26 +157,25 @@
 	  Say Y to include support for SBS battery driver for SBS-compliant
 	  gas gauges.
 
-config BATTERY_BQ27x00
-	tristate "BQ27x00 battery driver"
-	depends on I2C || I2C=n
+config BATTERY_BQ27XXX
+	tristate "BQ27xxx battery driver"
 	help
-	  Say Y here to enable support for batteries with BQ27x00 (I2C/HDQ) chips.
+	  Say Y here to enable support for batteries with BQ27xxx (I2C/HDQ) chips.
 
-config BATTERY_BQ27X00_I2C
-	bool "BQ27200/BQ27500 support"
-	depends on BATTERY_BQ27x00
+config BATTERY_BQ27XXX_I2C
+	bool "BQ27xxx I2C support"
+	depends on BATTERY_BQ27XXX
 	depends on I2C
 	default y
 	help
-	  Say Y here to enable support for batteries with BQ27x00 (I2C) chips.
+	  Say Y here to enable support for batteries with BQ27xxx (I2C) chips.
 
-config BATTERY_BQ27X00_PLATFORM
-	bool "BQ27000 support"
-	depends on BATTERY_BQ27x00
+config BATTERY_BQ27XXX_PLATFORM
+	bool "BQ27xxx HDQ support"
+	depends on BATTERY_BQ27XXX
 	default y
 	help
-	  Say Y here to enable support for batteries with BQ27000 (HDQ) chips.
+	  Say Y here to enable support for batteries with BQ27xxx (HDQ) chips.
 
 config BATTERY_DA9030
 	tristate "DA9030 battery driver"
@@ -313,7 +312,7 @@
 
 config CHARGER_TWL4030
 	tristate "OMAP TWL4030 BCI charger driver"
-	depends on TWL4030_CORE
+	depends on IIO && TWL4030_CORE
 	help
 	  Say Y here to enable support for TWL4030 Battery Charge Interface.
 
@@ -379,6 +378,18 @@
 	  Say Y to enable support for the battery charger control sysfs and
 	  platform data of MAX8998/LP3974 PMICs.
 
+config CHARGER_QCOM_SMBB
+	tristate "Qualcomm Switch-Mode Battery Charger and Boost"
+	depends on MFD_SPMI_PMIC || COMPILE_TEST
+	depends on OF
+	help
+	  Say Y to include support for the Switch-Mode Battery Charger and
+	  Boost (SMBB) hardware found in Qualcomm PM8941 PMICs.  The charger
+	  is an integrated, single-cell lithium-ion battery charger.  DT
+	  configuration is required for loading, see the devicetree
+	  documentation for more detail.  The base name for this driver is
+	  'pm8941_charger'.
+
 config CHARGER_BQ2415X
 	tristate "TI BQ2415x battery charger driver"
 	depends on I2C
@@ -397,12 +408,13 @@
 	  Say Y to enable support for the TI BQ24190 battery charger.
 
 config CHARGER_BQ24257
-	tristate "TI BQ24257 battery charger driver"
+	tristate "TI BQ24250/24251/24257 battery charger driver"
 	depends on I2C
 	depends on GPIOLIB || COMPILE_TEST
 	depends on REGMAP_I2C
 	help
-	  Say Y to enable support for the TI BQ24257 battery charger.
+	  Say Y to enable support for the TI BQ24250, BQ24251, and BQ24257 battery
+	  chargers.
 
 config CHARGER_BQ24735
 	tristate "TI BQ24735 battery charger support"
@@ -434,6 +446,13 @@
 	 Say Y here to enable support for battery charging with TPS65090
 	 PMIC chips.
 
+config CHARGER_TPS65217
+	tristate "TPS65217 battery charger driver"
+	depends on MFD_TPS65217
+	help
+	 Say Y here to enable support for battery charging with TPS65217
+	 PMIC chips.
+
 config BATTERY_GAUGE_LTC2941
 	tristate "LTC2941/LTC2943 Battery Gauge Driver"
 	depends on I2C
@@ -472,6 +491,13 @@
 	help
 	  Say Y to enable support for Richtek RT9455 battery charger.
 
+config AXP20X_POWER
+	tristate "AXP20x power supply driver"
+	depends on MFD_AXP20X
+	help
+	  This driver provides support for the power supply features of
+	  AXP20x PMIC.
+
 source "drivers/power/reset/Kconfig"
 
 endif # POWER_SUPPLY
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index 5752ce8..b0e1bf1 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -9,6 +9,7 @@
 
 obj-$(CONFIG_PDA_POWER)		+= pda_power.o
 obj-$(CONFIG_APM_POWER)		+= apm_power.o
+obj-$(CONFIG_AXP20X_POWER)	+= axp20x_usb_power.o
 obj-$(CONFIG_MAX8925_POWER)	+= max8925_power.o
 obj-$(CONFIG_WM831X_BACKUP)	+= wm831x_backup.o
 obj-$(CONFIG_WM831X_POWER)	+= wm831x_power.o
@@ -29,7 +30,7 @@
 obj-$(CONFIG_BATTERY_IPAQ_MICRO) += ipaq_micro_battery.o
 obj-$(CONFIG_BATTERY_WM97XX)	+= wm97xx_battery.o
 obj-$(CONFIG_BATTERY_SBS)	+= sbs-battery.o
-obj-$(CONFIG_BATTERY_BQ27x00)	+= bq27x00_battery.o
+obj-$(CONFIG_BATTERY_BQ27XXX)	+= bq27xxx_battery.o
 obj-$(CONFIG_BATTERY_DA9030)	+= da9030_battery.o
 obj-$(CONFIG_BATTERY_DA9052)	+= da9052-battery.o
 obj-$(CONFIG_CHARGER_DA9150)	+= da9150-charger.o
@@ -57,6 +58,7 @@
 obj-$(CONFIG_CHARGER_MAX77693)	+= max77693_charger.o
 obj-$(CONFIG_CHARGER_MAX8997)	+= max8997_charger.o
 obj-$(CONFIG_CHARGER_MAX8998)	+= max8998_charger.o
+obj-$(CONFIG_CHARGER_QCOM_SMBB)	+= qcom_smbb.o
 obj-$(CONFIG_CHARGER_BQ2415X)	+= bq2415x_charger.o
 obj-$(CONFIG_CHARGER_BQ24190)	+= bq24190_charger.o
 obj-$(CONFIG_CHARGER_BQ24257)	+= bq24257_charger.o
@@ -65,6 +67,7 @@
 obj-$(CONFIG_POWER_AVS)		+= avs/
 obj-$(CONFIG_CHARGER_SMB347)	+= smb347-charger.o
 obj-$(CONFIG_CHARGER_TPS65090)	+= tps65090-charger.o
+obj-$(CONFIG_CHARGER_TPS65217)	+= tps65217_charger.o
 obj-$(CONFIG_POWER_RESET)	+= reset/
 obj-$(CONFIG_AXP288_FUEL_GAUGE) += axp288_fuel_gauge.o
 obj-$(CONFIG_AXP288_CHARGER)	+= axp288_charger.o
diff --git a/drivers/power/axp20x_usb_power.c b/drivers/power/axp20x_usb_power.c
new file mode 100644
index 0000000..421a90b
--- /dev/null
+++ b/drivers/power/axp20x_usb_power.c
@@ -0,0 +1,248 @@
+/*
+ * AXP20x PMIC USB power supply status driver
+ *
+ * Copyright (C) 2015 Hans de Goede <hdegoede@redhat.com>
+ * Copyright (C) 2014 Bruno Prémont <bonbons@linux-vserver.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under  the terms of the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define DRVNAME "axp20x-usb-power-supply"
+
+#define AXP20X_PWR_STATUS_VBUS_PRESENT	BIT(5)
+#define AXP20X_PWR_STATUS_VBUS_USED	BIT(4)
+
+#define AXP20X_USB_STATUS_VBUS_VALID	BIT(2)
+
+#define AXP20X_VBUS_VHOLD_uV(b)		(4000000 + (((b) >> 3) & 7) * 100000)
+#define AXP20X_VBUS_CLIMIT_MASK		3
+#define AXP20X_VBUC_CLIMIT_900mA	0
+#define AXP20X_VBUC_CLIMIT_500mA	1
+#define AXP20X_VBUC_CLIMIT_100mA	2
+#define AXP20X_VBUC_CLIMIT_NONE		3
+
+#define AXP20X_ADC_EN1_VBUS_CURR	BIT(2)
+#define AXP20X_ADC_EN1_VBUS_VOLT	BIT(3)
+
+#define AXP20X_VBUS_MON_VBUS_VALID	BIT(3)
+
+struct axp20x_usb_power {
+	struct regmap *regmap;
+	struct power_supply *supply;
+};
+
+static irqreturn_t axp20x_usb_power_irq(int irq, void *devid)
+{
+	struct axp20x_usb_power *power = devid;
+
+	power_supply_changed(power->supply);
+
+	return IRQ_HANDLED;
+}
+
+static int axp20x_usb_power_get_property(struct power_supply *psy,
+	enum power_supply_property psp, union power_supply_propval *val)
+{
+	struct axp20x_usb_power *power = power_supply_get_drvdata(psy);
+	unsigned int input, v;
+	int ret;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
+		ret = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+		if (ret)
+			return ret;
+
+		val->intval = AXP20X_VBUS_VHOLD_uV(v);
+		return 0;
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		ret = axp20x_read_variable_width(power->regmap,
+						 AXP20X_VBUS_V_ADC_H, 12);
+		if (ret < 0)
+			return ret;
+
+		val->intval = ret * 1700; /* 1 step = 1.7 mV */
+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_MAX:
+		ret = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+		if (ret)
+			return ret;
+
+		switch (v & AXP20X_VBUS_CLIMIT_MASK) {
+		case AXP20X_VBUC_CLIMIT_100mA:
+			val->intval = 100000;
+			break;
+		case AXP20X_VBUC_CLIMIT_500mA:
+			val->intval = 500000;
+			break;
+		case AXP20X_VBUC_CLIMIT_900mA:
+			val->intval = 900000;
+			break;
+		case AXP20X_VBUC_CLIMIT_NONE:
+			val->intval = -1;
+			break;
+		}
+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		ret = axp20x_read_variable_width(power->regmap,
+						 AXP20X_VBUS_I_ADC_H, 12);
+		if (ret < 0)
+			return ret;
+
+		val->intval = ret * 375; /* 1 step = 0.375 mA */
+		return 0;
+	default:
+		break;
+	}
+
+	/* All the properties below need the input-status reg value */
+	ret = regmap_read(power->regmap, AXP20X_PWR_INPUT_STATUS, &input);
+	if (ret)
+		return ret;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_HEALTH:
+		if (!(input & AXP20X_PWR_STATUS_VBUS_PRESENT)) {
+			val->intval = POWER_SUPPLY_HEALTH_UNKNOWN;
+			break;
+		}
+
+		ret = regmap_read(power->regmap, AXP20X_USB_OTG_STATUS, &v);
+		if (ret)
+			return ret;
+
+		if (!(v & AXP20X_USB_STATUS_VBUS_VALID)) {
+			val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
+			break;
+		}
+
+		val->intval = POWER_SUPPLY_HEALTH_GOOD;
+		break;
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_PRESENT);
+		break;
+	case POWER_SUPPLY_PROP_ONLINE:
+		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_USED);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static enum power_supply_property axp20x_usb_power_properties[] = {
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_MAX,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+};
+
+static const struct power_supply_desc axp20x_usb_power_desc = {
+	.name = "axp20x-usb",
+	.type = POWER_SUPPLY_TYPE_USB,
+	.properties = axp20x_usb_power_properties,
+	.num_properties = ARRAY_SIZE(axp20x_usb_power_properties),
+	.get_property = axp20x_usb_power_get_property,
+};
+
+static int axp20x_usb_power_probe(struct platform_device *pdev)
+{
+	struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
+	struct power_supply_config psy_cfg = {};
+	struct axp20x_usb_power *power;
+	static const char * const irq_names[] = { "VBUS_PLUGIN",
+		"VBUS_REMOVAL", "VBUS_VALID", "VBUS_NOT_VALID" };
+	int i, irq, ret;
+
+	if (!of_device_is_available(pdev->dev.of_node))
+		return -ENODEV;
+
+	if (!axp20x) {
+		dev_err(&pdev->dev, "Parent drvdata not set\n");
+		return -EINVAL;
+	}
+
+	power = devm_kzalloc(&pdev->dev, sizeof(*power), GFP_KERNEL);
+	if (!power)
+		return -ENOMEM;
+
+	power->regmap = axp20x->regmap;
+
+	/* Enable vbus valid checking */
+	ret = regmap_update_bits(power->regmap, AXP20X_VBUS_MON,
+		    AXP20X_VBUS_MON_VBUS_VALID, AXP20X_VBUS_MON_VBUS_VALID);
+	if (ret)
+		return ret;
+
+	/* Enable vbus voltage and current measurement */
+	ret = regmap_update_bits(power->regmap, AXP20X_ADC_EN1,
+			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT,
+			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT);
+	if (ret)
+		return ret;
+
+	psy_cfg.of_node = pdev->dev.of_node;
+	psy_cfg.drv_data = power;
+
+	power->supply = devm_power_supply_register(&pdev->dev,
+					&axp20x_usb_power_desc, &psy_cfg);
+	if (IS_ERR(power->supply))
+		return PTR_ERR(power->supply);
+
+	/* Request irqs after registering, as irqs may trigger immediately */
+	for (i = 0; i < ARRAY_SIZE(irq_names); i++) {
+		irq = platform_get_irq_byname(pdev, irq_names[i]);
+		if (irq < 0) {
+			dev_warn(&pdev->dev, "No IRQ for %s: %d\n",
+				 irq_names[i], irq);
+			continue;
+		}
+		irq = regmap_irq_get_virq(axp20x->regmap_irqc, irq);
+		ret = devm_request_any_context_irq(&pdev->dev, irq,
+				axp20x_usb_power_irq, 0, DRVNAME, power);
+		if (ret < 0)
+			dev_warn(&pdev->dev, "Error requesting %s IRQ: %d\n",
+				 irq_names[i], ret);
+	}
+
+	return 0;
+}
+
+static const struct of_device_id axp20x_usb_power_match[] = {
+	{ .compatible = "x-powers,axp202-usb-power-supply" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, axp20x_usb_power_match);
+
+static struct platform_driver axp20x_usb_power_driver = {
+	.probe = axp20x_usb_power_probe,
+	.driver = {
+		.name = DRVNAME,
+		.of_match_table = axp20x_usb_power_match,
+	},
+};
+
+module_platform_driver(axp20x_usb_power_driver);
+
+MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
+MODULE_DESCRIPTION("AXP20x PMIC USB power supply status driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/power/bq2415x_charger.c b/drivers/power/bq2415x_charger.c
index ec212b5..4afd768 100644
--- a/drivers/power/bq2415x_charger.c
+++ b/drivers/power/bq2415x_charger.c
@@ -1704,7 +1704,7 @@
 error_3:
 	bq2415x_power_supply_exit(bq);
 error_2:
-	if (bq->notify_node)
+	if (bq && bq->notify_node)
 		of_node_put(bq->notify_node);
 	kfree(name);
 error_1:
diff --git a/drivers/power/bq24190_charger.c b/drivers/power/bq24190_charger.c
index 469a452..f5746b9 100644
--- a/drivers/power/bq24190_charger.c
+++ b/drivers/power/bq24190_charger.c
@@ -1543,5 +1543,4 @@
 
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Mark A. Greer <mgreer@animalcreek.com>");
-MODULE_ALIAS("i2c:bq24190-charger");
 MODULE_DESCRIPTION("TI BQ24190 Charger Driver");
diff --git a/drivers/power/bq24257_charger.c b/drivers/power/bq24257_charger.c
index 5859bc7..1fea2c7 100644
--- a/drivers/power/bq24257_charger.c
+++ b/drivers/power/bq24257_charger.c
@@ -13,6 +13,10 @@
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
+ * Datasheets:
+ * http://www.ti.com/product/bq24250
+ * http://www.ti.com/product/bq24251
+ * http://www.ti.com/product/bq24257
  */
 
 #include <linux/module.h>
@@ -36,18 +40,33 @@
 #define BQ24257_REG_7			0x06
 
 #define BQ24257_MANUFACTURER		"Texas Instruments"
-#define BQ24257_STAT_IRQ		"stat"
 #define BQ24257_PG_GPIO			"pg"
 
 #define BQ24257_ILIM_SET_DELAY		1000	/* msec */
 
+/*
+ * When adding support for new devices make sure that enum bq2425x_chip and
+ * bq2425x_chip_name[] always stay in sync!
+ */
+enum bq2425x_chip {
+	BQ24250,
+	BQ24251,
+	BQ24257,
+};
+
+static const char *const bq2425x_chip_name[] = {
+	"bq24250",
+	"bq24251",
+	"bq24257",
+};
+
 enum bq24257_fields {
 	F_WD_FAULT, F_WD_EN, F_STAT, F_FAULT,			    /* REG 1 */
 	F_RESET, F_IILIMIT, F_EN_STAT, F_EN_TERM, F_CE, F_HZ_MODE,  /* REG 2 */
 	F_VBAT, F_USB_DET,					    /* REG 3 */
 	F_ICHG, F_ITERM,					    /* REG 4 */
 	F_LOOP_STATUS, F_LOW_CHG, F_DPDM_EN, F_CE_STATUS, F_VINDPM, /* REG 5 */
-	F_X2_TMR_EN, F_TMR, F_SYSOFF, F_TS_STAT,		    /* REG 6 */
+	F_X2_TMR_EN, F_TMR, F_SYSOFF, F_TS_EN, F_TS_STAT,	    /* REG 6 */
 	F_VOVP, F_CLR_VDP, F_FORCE_BATDET, F_FORCE_PTM,		    /* REG 7 */
 
 	F_MAX_FIELDS
@@ -58,6 +77,9 @@
 	u8 ichg;	/* charge current      */
 	u8 vbat;	/* regulation voltage  */
 	u8 iterm;	/* termination current */
+	u8 iilimit;	/* input current limit */
+	u8 vovp;	/* over voltage protection voltage */
+	u8 vindpm;	/* VDMP input threshold voltage */
 };
 
 struct bq24257_state {
@@ -71,6 +93,8 @@
 	struct device *dev;
 	struct power_supply *charger;
 
+	enum bq2425x_chip chip;
+
 	struct regmap *rmap;
 	struct regmap_field *rmap_fields[F_MAX_FIELDS];
 
@@ -82,6 +106,8 @@
 	struct bq24257_state state;
 
 	struct mutex lock; /* protect state data */
+
+	bool iilimit_autoset_enable;
 };
 
 static bool bq24257_is_volatile_reg(struct device *dev, unsigned int reg)
@@ -135,6 +161,7 @@
 	[F_X2_TMR_EN]		= REG_FIELD(BQ24257_REG_6, 7, 7),
 	[F_TMR]			= REG_FIELD(BQ24257_REG_6, 5, 6),
 	[F_SYSOFF]		= REG_FIELD(BQ24257_REG_6, 4, 4),
+	[F_TS_EN]		= REG_FIELD(BQ24257_REG_6, 3, 3),
 	[F_TS_STAT]		= REG_FIELD(BQ24257_REG_6, 0, 2),
 	/* REG 7 */
 	[F_VOVP]		= REG_FIELD(BQ24257_REG_7, 5, 7),
@@ -169,6 +196,26 @@
 
 #define BQ24257_ITERM_MAP_SIZE		ARRAY_SIZE(bq24257_iterm_map)
 
+static const u32 bq24257_iilimit_map[] = {
+	100000, 150000, 500000, 900000, 1500000, 2000000
+};
+
+#define BQ24257_IILIMIT_MAP_SIZE	ARRAY_SIZE(bq24257_iilimit_map)
+
+static const u32 bq24257_vovp_map[] = {
+	6000000, 6500000, 7000000, 8000000, 9000000, 9500000, 10000000,
+	10500000
+};
+
+#define BQ24257_VOVP_MAP_SIZE		ARRAY_SIZE(bq24257_vovp_map)
+
+static const u32 bq24257_vindpm_map[] = {
+	4200000, 4280000, 4360000, 4440000, 4520000, 4600000, 4680000,
+	4760000
+};
+
+#define BQ24257_VINDPM_MAP_SIZE		ARRAY_SIZE(bq24257_vindpm_map)
+
 static int bq24257_field_read(struct bq24257_device *bq,
 			      enum bq24257_fields field_id)
 {
@@ -220,6 +267,47 @@
 	FAULT_INPUT_LDO_LOW,
 };
 
+static int bq24257_get_input_current_limit(struct bq24257_device *bq,
+					   union power_supply_propval *val)
+{
+	int ret;
+
+	ret = bq24257_field_read(bq, F_IILIMIT);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * The "External ILIM" and "Production & Test" modes are not exposed
+	 * through this driver and not being covered by the lookup table.
+	 * Should such a mode have become active let's return an error rather
+	 * than exceeding the bounds of the lookup table and returning
+	 * garbage.
+	 */
+	if (ret >= BQ24257_IILIMIT_MAP_SIZE)
+		return -ENODATA;
+
+	val->intval = bq24257_iilimit_map[ret];
+
+	return 0;
+}
+
+static int bq24257_set_input_current_limit(struct bq24257_device *bq,
+					const union power_supply_propval *val)
+{
+	/*
+	 * Address the case where the user manually sets an input current limit
+	 * while the charger auto-detection mechanism is is active. In this
+	 * case we want to abort and go straight to the user-specified value.
+	 */
+	if (bq->iilimit_autoset_enable)
+		cancel_delayed_work_sync(&bq->iilimit_setup_work);
+
+	return bq24257_field_write(bq, F_IILIMIT,
+				   bq24257_find_idx(val->intval,
+						    bq24257_iilimit_map,
+						    BQ24257_IILIMIT_MAP_SIZE));
+}
+
 static int bq24257_power_supply_get_property(struct power_supply *psy,
 					     enum power_supply_property psp,
 					     union power_supply_propval *val)
@@ -249,6 +337,10 @@
 		val->strval = BQ24257_MANUFACTURER;
 		break;
 
+	case POWER_SUPPLY_PROP_MODEL_NAME:
+		val->strval = bq2425x_chip_name[bq->chip];
+		break;
+
 	case POWER_SUPPLY_PROP_ONLINE:
 		val->intval = state.power_good;
 		break;
@@ -300,6 +392,9 @@
 		val->intval = bq24257_iterm_map[bq->init_data.iterm];
 		break;
 
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		return bq24257_get_input_current_limit(bq, val);
+
 	default:
 		return -EINVAL;
 	}
@@ -307,6 +402,31 @@
 	return 0;
 }
 
+static int bq24257_power_supply_set_property(struct power_supply *psy,
+					enum power_supply_property prop,
+					const union power_supply_propval *val)
+{
+	struct bq24257_device *bq = power_supply_get_drvdata(psy);
+
+	switch (prop) {
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		return bq24257_set_input_current_limit(bq, val);
+	default:
+		return -EINVAL;
+	}
+}
+
+static int bq24257_power_supply_property_is_writeable(struct power_supply *psy,
+					enum power_supply_property psp)
+{
+	switch (psp) {
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		return true;
+	default:
+		return false;
+	}
+}
+
 static int bq24257_get_chip_state(struct bq24257_device *bq,
 				  struct bq24257_state *state)
 {
@@ -324,7 +444,26 @@
 
 	state->fault = ret;
 
-	state->power_good = !gpiod_get_value_cansleep(bq->pg);
+	if (bq->pg)
+		state->power_good = !gpiod_get_value_cansleep(bq->pg);
+	else
+		/*
+		 * If we have a chip without a dedicated power-good GPIO or
+		 * some other explicit bit that would provide this information
+		 * assume the power is good if there is no supply related
+		 * fault - and not good otherwise. There is a possibility for
+		 * other errors to mask that power in fact is not good but this
+		 * is probably the best we can do here.
+		 */
+		switch (state->fault) {
+		case FAULT_INPUT_OVP:
+		case FAULT_INPUT_UVLO:
+		case FAULT_INPUT_LDO_LOW:
+			state->power_good = false;
+			break;
+		default:
+			state->power_good = true;
+		}
 
 	return 0;
 }
@@ -361,6 +500,28 @@
 	IILIMIT_NONE,
 };
 
+enum bq24257_vovp {
+	VOVP_6000,
+	VOVP_6500,
+	VOVP_7000,
+	VOVP_8000,
+	VOVP_9000,
+	VOVP_9500,
+	VOVP_10000,
+	VOVP_10500
+};
+
+enum bq24257_vindpm {
+	VINDPM_4200,
+	VINDPM_4280,
+	VINDPM_4360,
+	VINDPM_4440,
+	VINDPM_4520,
+	VINDPM_4600,
+	VINDPM_4680,
+	VINDPM_4760
+};
+
 enum bq24257_port_type {
 	PORT_TYPE_DCP,		/* Dedicated Charging Port */
 	PORT_TYPE_CDP,		/* Charging Downstream Port */
@@ -449,41 +610,43 @@
 {
 	int ret;
 	struct bq24257_state old_state;
-	bool reset_iilimit = false;
-	bool config_iilimit = false;
 
 	mutex_lock(&bq->lock);
 	old_state = bq->state;
 	mutex_unlock(&bq->lock);
 
-	if (!new_state->power_good) {			     /* power removed */
-		cancel_delayed_work_sync(&bq->iilimit_setup_work);
+	/*
+	 * Handle BQ2425x state changes observing whether the D+/D- based input
+	 * current limit autoset functionality is enabled.
+	 */
+	if (!new_state->power_good) {
+		dev_dbg(bq->dev, "Power removed\n");
+		if (bq->iilimit_autoset_enable) {
+			cancel_delayed_work_sync(&bq->iilimit_setup_work);
 
-		/* activate D+/D- port detection algorithm */
-		ret = bq24257_field_write(bq, F_DPDM_EN, 1);
+			/* activate D+/D- port detection algorithm */
+			ret = bq24257_field_write(bq, F_DPDM_EN, 1);
+			if (ret < 0)
+				goto error;
+		}
+		/*
+		 * When power is removed always return to the default input
+		 * current limit as configured during probe.
+		 */
+		ret = bq24257_field_write(bq, F_IILIMIT, bq->init_data.iilimit);
 		if (ret < 0)
 			goto error;
+	} else if (!old_state.power_good) {
+		dev_dbg(bq->dev, "Power inserted\n");
 
-		reset_iilimit = true;
-	} else if (!old_state.power_good) {		    /* power inserted */
-		config_iilimit = true;
-	} else if (new_state->fault == FAULT_NO_BAT) {	   /* battery removed */
-		cancel_delayed_work_sync(&bq->iilimit_setup_work);
-
-		reset_iilimit = true;
-	} else if (old_state.fault == FAULT_NO_BAT) {    /* battery connected */
-		config_iilimit = true;
-	} else if (new_state->fault == FAULT_TIMER) { /* safety timer expired */
-		dev_err(bq->dev, "Safety timer expired! Battery dead?\n");
-	}
-
-	if (reset_iilimit) {
-		ret = bq24257_field_write(bq, F_IILIMIT, IILIMIT_500);
-		if (ret < 0)
-			goto error;
-	} else if (config_iilimit) {
-		schedule_delayed_work(&bq->iilimit_setup_work,
+		if (bq->iilimit_autoset_enable)
+			/* configure input current limit */
+			schedule_delayed_work(&bq->iilimit_setup_work,
 				      msecs_to_jiffies(BQ24257_ILIM_SET_DELAY));
+	} else if (new_state->fault == FAULT_NO_BAT) {
+		dev_warn(bq->dev, "Battery removed\n");
+	} else if (new_state->fault == FAULT_TIMER) {
+		dev_err(bq->dev, "Safety timer expired! Battery dead?\n");
 	}
 
 	return;
@@ -531,7 +694,9 @@
 	} init_data[] = {
 		{F_ICHG, bq->init_data.ichg},
 		{F_VBAT, bq->init_data.vbat},
-		{F_ITERM, bq->init_data.iterm}
+		{F_ITERM, bq->init_data.iterm},
+		{F_VOVP, bq->init_data.vovp},
+		{F_VINDPM, bq->init_data.vindpm},
 	};
 
 	/*
@@ -558,7 +723,16 @@
 	bq->state = state;
 	mutex_unlock(&bq->lock);
 
-	if (!state.power_good)
+	if (!bq->iilimit_autoset_enable) {
+		dev_dbg(bq->dev, "manually setting iilimit = %u\n",
+			bq->init_data.iilimit);
+
+		/* program fixed input current limit */
+		ret = bq24257_field_write(bq, F_IILIMIT,
+					  bq->init_data.iilimit);
+		if (ret < 0)
+			return ret;
+	} else if (!state.power_good)
 		/* activate D+/D- detection algorithm */
 		ret = bq24257_field_write(bq, F_DPDM_EN, 1);
 	else if (state.fault != FAULT_NO_BAT)
@@ -569,6 +743,7 @@
 
 static enum power_supply_property bq24257_power_supply_props[] = {
 	POWER_SUPPLY_PROP_MANUFACTURER,
+	POWER_SUPPLY_PROP_MODEL_NAME,
 	POWER_SUPPLY_PROP_STATUS,
 	POWER_SUPPLY_PROP_ONLINE,
 	POWER_SUPPLY_PROP_HEALTH,
@@ -577,6 +752,7 @@
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX,
 	POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT,
+	POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
 };
 
 static char *bq24257_charger_supplied_to[] = {
@@ -589,6 +765,96 @@
 	.properties = bq24257_power_supply_props,
 	.num_properties = ARRAY_SIZE(bq24257_power_supply_props),
 	.get_property = bq24257_power_supply_get_property,
+	.set_property = bq24257_power_supply_set_property,
+	.property_is_writeable = bq24257_power_supply_property_is_writeable,
+};
+
+static ssize_t bq24257_show_ovp_voltage(struct device *dev,
+					struct device_attribute *attr,
+					char *buf)
+{
+	struct power_supply *psy = dev_get_drvdata(dev);
+	struct bq24257_device *bq = power_supply_get_drvdata(psy);
+
+	return scnprintf(buf, PAGE_SIZE, "%u\n",
+			 bq24257_vovp_map[bq->init_data.vovp]);
+}
+
+static ssize_t bq24257_show_in_dpm_voltage(struct device *dev,
+					   struct device_attribute *attr,
+					   char *buf)
+{
+	struct power_supply *psy = dev_get_drvdata(dev);
+	struct bq24257_device *bq = power_supply_get_drvdata(psy);
+
+	return scnprintf(buf, PAGE_SIZE, "%u\n",
+			 bq24257_vindpm_map[bq->init_data.vindpm]);
+}
+
+static ssize_t bq24257_sysfs_show_enable(struct device *dev,
+					 struct device_attribute *attr,
+					 char *buf)
+{
+	struct power_supply *psy = dev_get_drvdata(dev);
+	struct bq24257_device *bq = power_supply_get_drvdata(psy);
+	int ret;
+
+	if (strcmp(attr->attr.name, "high_impedance_enable") == 0)
+		ret = bq24257_field_read(bq, F_HZ_MODE);
+	else if (strcmp(attr->attr.name, "sysoff_enable") == 0)
+		ret = bq24257_field_read(bq, F_SYSOFF);
+	else
+		return -EINVAL;
+
+	if (ret < 0)
+		return ret;
+
+	return scnprintf(buf, PAGE_SIZE, "%d\n", ret);
+}
+
+static ssize_t bq24257_sysfs_set_enable(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf,
+					size_t count)
+{
+	struct power_supply *psy = dev_get_drvdata(dev);
+	struct bq24257_device *bq = power_supply_get_drvdata(psy);
+	long val;
+	int ret;
+
+	if (kstrtol(buf, 10, &val) < 0)
+		return -EINVAL;
+
+	if (strcmp(attr->attr.name, "high_impedance_enable") == 0)
+		ret = bq24257_field_write(bq, F_HZ_MODE, (bool)val);
+	else if (strcmp(attr->attr.name, "sysoff_enable") == 0)
+		ret = bq24257_field_write(bq, F_SYSOFF, (bool)val);
+	else
+		return -EINVAL;
+
+	if (ret < 0)
+		return ret;
+
+	return count;
+}
+
+static DEVICE_ATTR(ovp_voltage, S_IRUGO, bq24257_show_ovp_voltage, NULL);
+static DEVICE_ATTR(in_dpm_voltage, S_IRUGO, bq24257_show_in_dpm_voltage, NULL);
+static DEVICE_ATTR(high_impedance_enable, S_IWUSR | S_IRUGO,
+		   bq24257_sysfs_show_enable, bq24257_sysfs_set_enable);
+static DEVICE_ATTR(sysoff_enable, S_IWUSR | S_IRUGO,
+		   bq24257_sysfs_show_enable, bq24257_sysfs_set_enable);
+
+static struct attribute *bq24257_charger_attr[] = {
+	&dev_attr_ovp_voltage.attr,
+	&dev_attr_in_dpm_voltage.attr,
+	&dev_attr_high_impedance_enable.attr,
+	&dev_attr_sysoff_enable.attr,
+	NULL,
+};
+
+static const struct attribute_group bq24257_attr_group = {
+	.attrs = bq24257_charger_attr,
 };
 
 static int bq24257_power_supply_init(struct bq24257_device *bq)
@@ -598,36 +864,28 @@
 	psy_cfg.supplied_to = bq24257_charger_supplied_to;
 	psy_cfg.num_supplicants = ARRAY_SIZE(bq24257_charger_supplied_to);
 
-	bq->charger = power_supply_register(bq->dev, &bq24257_power_supply_desc,
-					    &psy_cfg);
-	if (IS_ERR(bq->charger))
-		return PTR_ERR(bq->charger);
+	bq->charger = devm_power_supply_register(bq->dev,
+						 &bq24257_power_supply_desc,
+						 &psy_cfg);
 
-	return 0;
+	return PTR_ERR_OR_ZERO(bq->charger);
 }
 
-static int bq24257_irq_probe(struct bq24257_device *bq)
+static void bq24257_pg_gpio_probe(struct bq24257_device *bq)
 {
-	struct gpio_desc *stat_irq;
+	bq->pg = devm_gpiod_get_optional(bq->dev, BQ24257_PG_GPIO, GPIOD_IN);
 
-	stat_irq = devm_gpiod_get_index(bq->dev, BQ24257_STAT_IRQ, 0, GPIOD_IN);
-	if (IS_ERR(stat_irq)) {
-		dev_err(bq->dev, "could not probe stat_irq pin\n");
-		return PTR_ERR(stat_irq);
+	if (PTR_ERR(bq->pg) == -EPROBE_DEFER) {
+		dev_info(bq->dev, "probe retry requested for PG pin\n");
+		return;
+	} else if (IS_ERR(bq->pg)) {
+		dev_err(bq->dev, "error probing PG pin\n");
+		bq->pg = NULL;
+		return;
 	}
 
-	return gpiod_to_irq(stat_irq);
-}
-
-static int bq24257_pg_gpio_probe(struct bq24257_device *bq)
-{
-	bq->pg = devm_gpiod_get_index(bq->dev, BQ24257_PG_GPIO, 0, GPIOD_IN);
-	if (IS_ERR(bq->pg)) {
-		dev_err(bq->dev, "could not probe PG pin\n");
-		return PTR_ERR(bq->pg);
-	}
-
-	return 0;
+	if (bq->pg)
+		dev_dbg(bq->dev, "probed PG pin = %d\n", desc_to_gpio(bq->pg));
 }
 
 static int bq24257_fw_probe(struct bq24257_device *bq)
@@ -635,6 +893,7 @@
 	int ret;
 	u32 property;
 
+	/* Required properties */
 	ret = device_property_read_u32(bq->dev, "ti,charge-current", &property);
 	if (ret < 0)
 		return ret;
@@ -658,6 +917,43 @@
 	bq->init_data.iterm = bq24257_find_idx(property, bq24257_iterm_map,
 					       BQ24257_ITERM_MAP_SIZE);
 
+	/* Optional properties. If not provided use reasonable default. */
+	ret = device_property_read_u32(bq->dev, "ti,current-limit",
+				       &property);
+	if (ret < 0) {
+		bq->iilimit_autoset_enable = true;
+
+		/*
+		 * Explicitly set a default value which will be needed for
+		 * devices that don't support the automatic setting of the input
+		 * current limit through the charger type detection mechanism.
+		 */
+		bq->init_data.iilimit = IILIMIT_500;
+	} else
+		bq->init_data.iilimit =
+				bq24257_find_idx(property,
+						 bq24257_iilimit_map,
+						 BQ24257_IILIMIT_MAP_SIZE);
+
+	ret = device_property_read_u32(bq->dev, "ti,ovp-voltage",
+				       &property);
+	if (ret < 0)
+		bq->init_data.vovp = VOVP_6500;
+	else
+		bq->init_data.vovp = bq24257_find_idx(property,
+						      bq24257_vovp_map,
+						      BQ24257_VOVP_MAP_SIZE);
+
+	ret = device_property_read_u32(bq->dev, "ti,in-dpm-voltage",
+				       &property);
+	if (ret < 0)
+		bq->init_data.vindpm = VINDPM_4360;
+	else
+		bq->init_data.vindpm =
+				bq24257_find_idx(property,
+						 bq24257_vindpm_map,
+						 BQ24257_VINDPM_MAP_SIZE);
+
 	return 0;
 }
 
@@ -666,6 +962,7 @@
 {
 	struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
 	struct device *dev = &client->dev;
+	const struct acpi_device_id *acpi_id;
 	struct bq24257_device *bq;
 	int ret;
 	int i;
@@ -682,6 +979,18 @@
 	bq->client = client;
 	bq->dev = dev;
 
+	if (ACPI_HANDLE(dev)) {
+		acpi_id = acpi_match_device(dev->driver->acpi_match_table,
+					    &client->dev);
+		if (!acpi_id) {
+			dev_err(dev, "Failed to match ACPI device\n");
+			return -ENODEV;
+		}
+		bq->chip = (enum bq2425x_chip)acpi_id->driver_data;
+	} else {
+		bq->chip = (enum bq2425x_chip)id->driver_data;
+	}
+
 	mutex_init(&bq->lock);
 
 	bq->rmap = devm_regmap_init_i2c(client, &bq24257_regmap_config);
@@ -703,8 +1012,6 @@
 
 	i2c_set_clientdata(client, bq);
 
-	INIT_DELAYED_WORK(&bq->iilimit_setup_work, bq24257_iilimit_setup_work);
-
 	if (!dev->platform_data) {
 		ret = bq24257_fw_probe(bq);
 		if (ret < 0) {
@@ -715,10 +1022,31 @@
 		return -ENODEV;
 	}
 
-	/* we can only check Power Good status by probing the PG pin */
-	ret = bq24257_pg_gpio_probe(bq);
-	if (ret < 0)
-		return ret;
+	/*
+	 * The BQ24250 doesn't support the D+/D- based charger type detection
+	 * used for the automatic setting of the input current limit setting so
+	 * explicitly disable that feature.
+	 */
+	if (bq->chip == BQ24250)
+		bq->iilimit_autoset_enable = false;
+
+	if (bq->iilimit_autoset_enable)
+		INIT_DELAYED_WORK(&bq->iilimit_setup_work,
+				  bq24257_iilimit_setup_work);
+
+	/*
+	 * The BQ24250 doesn't have a dedicated Power Good (PG) pin so let's
+	 * not probe for it and instead use a SW-based approach to determine
+	 * the PG state. We also use a SW-based approach for all other devices
+	 * if the PG pin is either not defined or can't be probed.
+	 */
+	if (bq->chip != BQ24250)
+		bq24257_pg_gpio_probe(bq);
+
+	if (PTR_ERR(bq->pg) == -EPROBE_DEFER)
+		return PTR_ERR(bq->pg);
+	else if (!bq->pg)
+		dev_info(bq->dev, "using SW-based power-good detection\n");
 
 	/* reset all registers to defaults */
 	ret = bq24257_field_write(bq, F_RESET, 1);
@@ -740,36 +1068,39 @@
 		return ret;
 	}
 
-	if (client->irq <= 0)
-		client->irq = bq24257_irq_probe(bq);
-
-	if (client->irq < 0) {
-		dev_err(dev, "no irq resource found\n");
-		return client->irq;
-	}
-
 	ret = devm_request_threaded_irq(dev, client->irq, NULL,
 					bq24257_irq_handler_thread,
 					IRQF_TRIGGER_FALLING |
 					IRQF_TRIGGER_RISING | IRQF_ONESHOT,
-					BQ24257_STAT_IRQ, bq);
-	if (ret)
+					bq2425x_chip_name[bq->chip], bq);
+	if (ret) {
+		dev_err(dev, "Failed to request IRQ #%d\n", client->irq);
 		return ret;
+	}
 
 	ret = bq24257_power_supply_init(bq);
-	if (ret < 0)
+	if (ret < 0) {
 		dev_err(dev, "Failed to register power supply\n");
+		return ret;
+	}
 
-	return ret;
+	ret = sysfs_create_group(&bq->charger->dev.kobj, &bq24257_attr_group);
+	if (ret < 0) {
+		dev_err(dev, "Can't create sysfs entries\n");
+		return ret;
+	}
+
+	return 0;
 }
 
 static int bq24257_remove(struct i2c_client *client)
 {
 	struct bq24257_device *bq = i2c_get_clientdata(client);
 
-	cancel_delayed_work_sync(&bq->iilimit_setup_work);
+	if (bq->iilimit_autoset_enable)
+		cancel_delayed_work_sync(&bq->iilimit_setup_work);
 
-	power_supply_unregister(bq->charger);
+	sysfs_remove_group(&bq->charger->dev.kobj, &bq24257_attr_group);
 
 	bq24257_field_write(bq, F_RESET, 1); /* reset to defaults */
 
@@ -782,7 +1113,8 @@
 	struct bq24257_device *bq = dev_get_drvdata(dev);
 	int ret = 0;
 
-	cancel_delayed_work_sync(&bq->iilimit_setup_work);
+	if (bq->iilimit_autoset_enable)
+		cancel_delayed_work_sync(&bq->iilimit_setup_work);
 
 	/* reset all registers to default (and activate standalone mode) */
 	ret = bq24257_field_write(bq, F_RESET, 1);
@@ -823,19 +1155,25 @@
 };
 
 static const struct i2c_device_id bq24257_i2c_ids[] = {
-	{ "bq24257", 0 },
+	{ "bq24250", BQ24250 },
+	{ "bq24251", BQ24251 },
+	{ "bq24257", BQ24257 },
 	{},
 };
 MODULE_DEVICE_TABLE(i2c, bq24257_i2c_ids);
 
 static const struct of_device_id bq24257_of_match[] = {
+	{ .compatible = "ti,bq24250", },
+	{ .compatible = "ti,bq24251", },
 	{ .compatible = "ti,bq24257", },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, bq24257_of_match);
 
 static const struct acpi_device_id bq24257_acpi_match[] = {
-	{"BQ242570", 0},
+	{ "BQ242500", BQ24250 },
+	{ "BQ242510", BQ24251 },
+	{ "BQ242570", BQ24257 },
 	{},
 };
 MODULE_DEVICE_TABLE(acpi, bq24257_acpi_match);
diff --git a/drivers/power/bq27x00_battery.c b/drivers/power/bq27x00_battery.c
deleted file mode 100644
index 8287261f..0000000
--- a/drivers/power/bq27x00_battery.c
+++ /dev/null
@@ -1,1129 +0,0 @@
-/*
- * BQ27x00 battery driver
- *
- * Copyright (C) 2008 Rodolfo Giometti <giometti@linux.it>
- * Copyright (C) 2008 Eurotech S.p.A. <info@eurotech.it>
- * Copyright (C) 2010-2011 Lars-Peter Clausen <lars@metafoo.de>
- * Copyright (C) 2011 Pali Rohár <pali.rohar@gmail.com>
- *
- * Based on a previous work by Copyright (C) 2008 Texas Instruments, Inc.
- *
- * This package is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
- * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.
- *
- * Datasheets:
- * http://focus.ti.com/docs/prod/folders/print/bq27000.html
- * http://focus.ti.com/docs/prod/folders/print/bq27500.html
- * http://www.ti.com/product/bq27425-g1
- * http://www.ti.com/product/BQ27742-G1
- * http://www.ti.com/product/BQ27510-G3
- */
-
-#include <linux/device.h>
-#include <linux/module.h>
-#include <linux/param.h>
-#include <linux/jiffies.h>
-#include <linux/workqueue.h>
-#include <linux/delay.h>
-#include <linux/platform_device.h>
-#include <linux/power_supply.h>
-#include <linux/idr.h>
-#include <linux/i2c.h>
-#include <linux/slab.h>
-#include <asm/unaligned.h>
-
-#include <linux/power/bq27x00_battery.h>
-
-#define DRIVER_VERSION		"1.2.0"
-
-#define BQ27XXX_MANUFACTURER	"Texas Instruments"
-
-#define BQ27x00_REG_TEMP	0x06
-#define BQ27x00_REG_VOLT	0x08
-#define BQ27x00_REG_AI		0x14
-#define BQ27x00_REG_FLAGS	0x0A
-#define BQ27x00_REG_TTE		0x16
-#define BQ27x00_REG_TTF		0x18
-#define BQ27x00_REG_TTECP	0x26
-#define BQ27x00_REG_NAC		0x0C /* Nominal available capacity */
-#define BQ27x00_REG_LMD		0x12 /* Last measured discharge */
-#define BQ27x00_REG_CYCT	0x2A /* Cycle count total */
-#define BQ27x00_REG_AE		0x22 /* Available energy */
-#define BQ27x00_POWER_AVG	0x24
-
-#define BQ27000_REG_RSOC	0x0B /* Relative State-of-Charge */
-#define BQ27000_REG_ILMD	0x76 /* Initial last measured discharge */
-#define BQ27000_FLAG_EDVF	BIT(0) /* Final End-of-Discharge-Voltage flag */
-#define BQ27000_FLAG_EDV1	BIT(1) /* First End-of-Discharge-Voltage flag */
-#define BQ27000_FLAG_CI		BIT(4) /* Capacity Inaccurate flag */
-#define BQ27000_FLAG_FC		BIT(5)
-#define BQ27000_FLAG_CHGS	BIT(7) /* Charge state flag */
-
-#define BQ27500_REG_SOC		0x2C
-#define BQ27500_REG_DCAP	0x3C /* Design capacity */
-#define BQ27500_FLAG_DSC	BIT(0)
-#define BQ27500_FLAG_SOCF	BIT(1) /* State-of-Charge threshold final */
-#define BQ27500_FLAG_SOC1	BIT(2) /* State-of-Charge threshold 1 */
-#define BQ27500_FLAG_FC		BIT(9)
-#define BQ27500_FLAG_OTC	BIT(15)
-
-#define BQ27742_POWER_AVG	0x76
-
-#define BQ27510_REG_SOC		0x20
-#define BQ27510_REG_DCAP	0x2E /* Design capacity */
-#define BQ27510_REG_CYCT	0x1E /* Cycle count total */
-
-/* bq27425 register addresses are same as bq27x00 addresses minus 4 */
-#define BQ27425_REG_OFFSET	0x04
-#define BQ27425_REG_SOC		(0x1C + BQ27425_REG_OFFSET)
-#define BQ27425_REG_DCAP	(0x3C + BQ27425_REG_OFFSET)
-
-#define BQ27000_RS			20 /* Resistor sense */
-#define BQ27x00_POWER_CONSTANT		(256 * 29200 / 1000)
-
-struct bq27x00_device_info;
-struct bq27x00_access_methods {
-	int (*read)(struct bq27x00_device_info *di, u8 reg, bool single);
-};
-
-enum bq27x00_chip { BQ27000, BQ27500, BQ27425, BQ27742, BQ27510};
-
-struct bq27x00_reg_cache {
-	int temperature;
-	int time_to_empty;
-	int time_to_empty_avg;
-	int time_to_full;
-	int charge_full;
-	int cycle_count;
-	int capacity;
-	int energy;
-	int flags;
-	int power_avg;
-	int health;
-};
-
-struct bq27x00_device_info {
-	struct device		*dev;
-	int			id;
-	enum bq27x00_chip	chip;
-
-	struct bq27x00_reg_cache cache;
-	int charge_design_full;
-
-	unsigned long last_update;
-	struct delayed_work work;
-
-	struct power_supply	*bat;
-
-	struct bq27x00_access_methods bus;
-
-	struct mutex lock;
-};
-
-static enum power_supply_property bq27x00_battery_props[] = {
-	POWER_SUPPLY_PROP_STATUS,
-	POWER_SUPPLY_PROP_PRESENT,
-	POWER_SUPPLY_PROP_VOLTAGE_NOW,
-	POWER_SUPPLY_PROP_CURRENT_NOW,
-	POWER_SUPPLY_PROP_CAPACITY,
-	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
-	POWER_SUPPLY_PROP_TEMP,
-	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
-	POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG,
-	POWER_SUPPLY_PROP_TIME_TO_FULL_NOW,
-	POWER_SUPPLY_PROP_TECHNOLOGY,
-	POWER_SUPPLY_PROP_CHARGE_FULL,
-	POWER_SUPPLY_PROP_CHARGE_NOW,
-	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
-	POWER_SUPPLY_PROP_CYCLE_COUNT,
-	POWER_SUPPLY_PROP_ENERGY_NOW,
-	POWER_SUPPLY_PROP_POWER_AVG,
-	POWER_SUPPLY_PROP_HEALTH,
-	POWER_SUPPLY_PROP_MANUFACTURER,
-};
-
-static enum power_supply_property bq27425_battery_props[] = {
-	POWER_SUPPLY_PROP_STATUS,
-	POWER_SUPPLY_PROP_PRESENT,
-	POWER_SUPPLY_PROP_VOLTAGE_NOW,
-	POWER_SUPPLY_PROP_CURRENT_NOW,
-	POWER_SUPPLY_PROP_CAPACITY,
-	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
-	POWER_SUPPLY_PROP_TEMP,
-	POWER_SUPPLY_PROP_TECHNOLOGY,
-	POWER_SUPPLY_PROP_CHARGE_FULL,
-	POWER_SUPPLY_PROP_CHARGE_NOW,
-	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
-	POWER_SUPPLY_PROP_MANUFACTURER,
-};
-
-static enum power_supply_property bq27742_battery_props[] = {
-	POWER_SUPPLY_PROP_STATUS,
-	POWER_SUPPLY_PROP_PRESENT,
-	POWER_SUPPLY_PROP_VOLTAGE_NOW,
-	POWER_SUPPLY_PROP_CURRENT_NOW,
-	POWER_SUPPLY_PROP_CAPACITY,
-	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
-	POWER_SUPPLY_PROP_TEMP,
-	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
-	POWER_SUPPLY_PROP_TECHNOLOGY,
-	POWER_SUPPLY_PROP_CHARGE_FULL,
-	POWER_SUPPLY_PROP_CHARGE_NOW,
-	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
-	POWER_SUPPLY_PROP_CYCLE_COUNT,
-	POWER_SUPPLY_PROP_POWER_AVG,
-	POWER_SUPPLY_PROP_HEALTH,
-	POWER_SUPPLY_PROP_MANUFACTURER,
-};
-
-static enum power_supply_property bq27510_battery_props[] = {
-	POWER_SUPPLY_PROP_STATUS,
-	POWER_SUPPLY_PROP_PRESENT,
-	POWER_SUPPLY_PROP_VOLTAGE_NOW,
-	POWER_SUPPLY_PROP_CURRENT_NOW,
-	POWER_SUPPLY_PROP_CAPACITY,
-	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
-	POWER_SUPPLY_PROP_TEMP,
-	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
-	POWER_SUPPLY_PROP_TECHNOLOGY,
-	POWER_SUPPLY_PROP_CHARGE_FULL,
-	POWER_SUPPLY_PROP_CHARGE_NOW,
-	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
-	POWER_SUPPLY_PROP_CYCLE_COUNT,
-	POWER_SUPPLY_PROP_POWER_AVG,
-	POWER_SUPPLY_PROP_HEALTH,
-	POWER_SUPPLY_PROP_MANUFACTURER,
-};
-
-static unsigned int poll_interval = 360;
-module_param(poll_interval, uint, 0644);
-MODULE_PARM_DESC(poll_interval,
-		 "battery poll interval in seconds - 0 disables polling");
-
-/*
- * Common code for BQ27x00 devices
- */
-
-static inline int bq27x00_read(struct bq27x00_device_info *di, u8 reg,
-			       bool single)
-{
-	if (di->chip == BQ27425)
-		return di->bus.read(di, reg - BQ27425_REG_OFFSET, single);
-	return di->bus.read(di, reg, single);
-}
-
-/*
- * Higher versions of the chip like BQ27425 and BQ27500
- * differ from BQ27000 and BQ27200 in calculation of certain
- * parameters. Hence we need to check for the chip type.
- */
-static bool bq27xxx_is_chip_version_higher(struct bq27x00_device_info *di)
-{
-	if (di->chip == BQ27425 || di->chip == BQ27500 || di->chip == BQ27742
-	    || di->chip == BQ27510)
-		return true;
-	return false;
-}
-
-/*
- * Return the battery Relative State-of-Charge
- * Or < 0 if something fails.
- */
-static int bq27x00_battery_read_rsoc(struct bq27x00_device_info *di)
-{
-	int rsoc;
-
-	if (di->chip == BQ27500 || di->chip == BQ27742)
-		rsoc = bq27x00_read(di, BQ27500_REG_SOC, false);
-	else if (di->chip == BQ27510)
-		rsoc = bq27x00_read(di, BQ27510_REG_SOC, false);
-	else if (di->chip == BQ27425)
-		rsoc = bq27x00_read(di, BQ27425_REG_SOC, false);
-	else
-		rsoc = bq27x00_read(di, BQ27000_REG_RSOC, true);
-
-	if (rsoc < 0)
-		dev_dbg(di->dev, "error reading relative State-of-Charge\n");
-
-	return rsoc;
-}
-
-/*
- * Return a battery charge value in µAh
- * Or < 0 if something fails.
- */
-static int bq27x00_battery_read_charge(struct bq27x00_device_info *di, u8 reg)
-{
-	int charge;
-
-	charge = bq27x00_read(di, reg, false);
-	if (charge < 0) {
-		dev_dbg(di->dev, "error reading charge register %02x: %d\n",
-			reg, charge);
-		return charge;
-	}
-
-	if (bq27xxx_is_chip_version_higher(di))
-		charge *= 1000;
-	else
-		charge = charge * 3570 / BQ27000_RS;
-
-	return charge;
-}
-
-/*
- * Return the battery Nominal available capaciy in µAh
- * Or < 0 if something fails.
- */
-static inline int bq27x00_battery_read_nac(struct bq27x00_device_info *di)
-{
-	int flags;
-	bool is_bq27500 = di->chip == BQ27500;
-	bool is_bq27742 = di->chip == BQ27742;
-	bool is_higher = bq27xxx_is_chip_version_higher(di);
-	bool flags_1b = !(is_bq27500 || is_bq27742);
-
-	flags = bq27x00_read(di, BQ27x00_REG_FLAGS, flags_1b);
-	if (flags >= 0 && !is_higher && (flags & BQ27000_FLAG_CI))
-		return -ENODATA;
-
-	return bq27x00_battery_read_charge(di, BQ27x00_REG_NAC);
-}
-
-/*
- * Return the battery Last measured discharge in µAh
- * Or < 0 if something fails.
- */
-static inline int bq27x00_battery_read_lmd(struct bq27x00_device_info *di)
-{
-	return bq27x00_battery_read_charge(di, BQ27x00_REG_LMD);
-}
-
-/*
- * Return the battery Initial last measured discharge in µAh
- * Or < 0 if something fails.
- */
-static int bq27x00_battery_read_ilmd(struct bq27x00_device_info *di)
-{
-	int ilmd;
-
-	if (bq27xxx_is_chip_version_higher(di)) {
-		if (di->chip == BQ27425)
-			ilmd = bq27x00_read(di, BQ27425_REG_DCAP, false);
-		else if (di->chip == BQ27510)
-			ilmd = bq27x00_read(di, BQ27510_REG_DCAP, false);
-		else
-			ilmd = bq27x00_read(di, BQ27500_REG_DCAP, false);
-	} else {
-		ilmd = bq27x00_read(di, BQ27000_REG_ILMD, true);
-	}
-
-	if (ilmd < 0) {
-		dev_dbg(di->dev, "error reading initial last measured discharge\n");
-		return ilmd;
-	}
-
-	if (bq27xxx_is_chip_version_higher(di))
-		ilmd *= 1000;
-	else
-		ilmd = ilmd * 256 * 3570 / BQ27000_RS;
-
-	return ilmd;
-}
-
-/*
- * Return the battery Available energy in µWh
- * Or < 0 if something fails.
- */
-static int bq27x00_battery_read_energy(struct bq27x00_device_info *di)
-{
-	int ae;
-
-	ae = bq27x00_read(di, BQ27x00_REG_AE, false);
-	if (ae < 0) {
-		dev_dbg(di->dev, "error reading available energy\n");
-		return ae;
-	}
-
-	if (di->chip == BQ27500)
-		ae *= 1000;
-	else
-		ae = ae * 29200 / BQ27000_RS;
-
-	return ae;
-}
-
-/*
- * Return the battery temperature in tenths of degree Kelvin
- * Or < 0 if something fails.
- */
-static int bq27x00_battery_read_temperature(struct bq27x00_device_info *di)
-{
-	int temp;
-
-	temp = bq27x00_read(di, BQ27x00_REG_TEMP, false);
-	if (temp < 0) {
-		dev_err(di->dev, "error reading temperature\n");
-		return temp;
-	}
-
-	if (!bq27xxx_is_chip_version_higher(di))
-		temp = 5 * temp / 2;
-
-	return temp;
-}
-
-/*
- * Return the battery Cycle count total
- * Or < 0 if something fails.
- */
-static int bq27x00_battery_read_cyct(struct bq27x00_device_info *di)
-{
-	int cyct;
-
-	if (di->chip == BQ27510)
-		cyct = bq27x00_read(di, BQ27510_REG_CYCT, false);
-	else
-		cyct = bq27x00_read(di, BQ27x00_REG_CYCT, false);
-	if (cyct < 0)
-		dev_err(di->dev, "error reading cycle count total\n");
-
-	return cyct;
-}
-
-/*
- * Read a time register.
- * Return < 0 if something fails.
- */
-static int bq27x00_battery_read_time(struct bq27x00_device_info *di, u8 reg)
-{
-	int tval;
-
-	tval = bq27x00_read(di, reg, false);
-	if (tval < 0) {
-		dev_dbg(di->dev, "error reading time register %02x: %d\n",
-			reg, tval);
-		return tval;
-	}
-
-	if (tval == 65535)
-		return -ENODATA;
-
-	return tval * 60;
-}
-
-/*
- * Read a power avg register.
- * Return < 0 if something fails.
- */
-static int bq27x00_battery_read_pwr_avg(struct bq27x00_device_info *di, u8 reg)
-{
-	int tval;
-
-	tval = bq27x00_read(di, reg, false);
-	if (tval < 0) {
-		dev_err(di->dev, "error reading power avg rgister  %02x: %d\n",
-			reg, tval);
-		return tval;
-	}
-
-	if (di->chip == BQ27500)
-		return tval;
-	else
-		return (tval * BQ27x00_POWER_CONSTANT) / BQ27000_RS;
-}
-
-/*
- * Read flag register.
- * Return < 0 if something fails.
- */
-static int bq27x00_battery_read_health(struct bq27x00_device_info *di)
-{
-	int tval;
-
-	tval = bq27x00_read(di, BQ27x00_REG_FLAGS, false);
-	if (tval < 0) {
-		dev_err(di->dev, "error reading flag register:%d\n", tval);
-		return tval;
-	}
-
-	if (di->chip == BQ27500) {
-		if (tval & BQ27500_FLAG_SOCF)
-			tval = POWER_SUPPLY_HEALTH_DEAD;
-		else if (tval & BQ27500_FLAG_OTC)
-			tval = POWER_SUPPLY_HEALTH_OVERHEAT;
-		else
-			tval = POWER_SUPPLY_HEALTH_GOOD;
-		return tval;
-	} else if (di->chip == BQ27510) {
-		if (tval & BQ27500_FLAG_OTC)
-			return POWER_SUPPLY_HEALTH_OVERHEAT;
-		return POWER_SUPPLY_HEALTH_GOOD;
-	} else {
-		if (tval & BQ27000_FLAG_EDV1)
-			tval = POWER_SUPPLY_HEALTH_DEAD;
-		else
-			tval = POWER_SUPPLY_HEALTH_GOOD;
-		return tval;
-	}
-
-	return -1;
-}
-
-static void bq27x00_update(struct bq27x00_device_info *di)
-{
-	struct bq27x00_reg_cache cache = {0, };
-	bool is_bq27500 = di->chip == BQ27500;
-	bool is_bq27510 = di->chip == BQ27510;
-	bool is_bq27425 = di->chip == BQ27425;
-	bool is_bq27742 = di->chip == BQ27742;
-	bool flags_1b = !(is_bq27500 || is_bq27742);
-
-	cache.flags = bq27x00_read(di, BQ27x00_REG_FLAGS, flags_1b);
-	if ((cache.flags & 0xff) == 0xff)
-		/* read error */
-		cache.flags = -1;
-	if (cache.flags >= 0) {
-		if (!is_bq27500 && !is_bq27425 && !is_bq27742 && !is_bq27510
-				&& (cache.flags & BQ27000_FLAG_CI)) {
-			dev_info(di->dev, "battery is not calibrated! ignoring capacity values\n");
-			cache.capacity = -ENODATA;
-			cache.energy = -ENODATA;
-			cache.time_to_empty = -ENODATA;
-			cache.time_to_empty_avg = -ENODATA;
-			cache.time_to_full = -ENODATA;
-			cache.charge_full = -ENODATA;
-			cache.health = -ENODATA;
-		} else {
-			cache.capacity = bq27x00_battery_read_rsoc(di);
-			if (is_bq27742 || is_bq27510)
-				cache.time_to_empty =
-					bq27x00_battery_read_time(di,
-							BQ27x00_REG_TTE);
-			else if (!is_bq27425) {
-				cache.energy = bq27x00_battery_read_energy(di);
-				cache.time_to_empty =
-					bq27x00_battery_read_time(di,
-							BQ27x00_REG_TTE);
-				cache.time_to_empty_avg =
-					bq27x00_battery_read_time(di,
-							BQ27x00_REG_TTECP);
-				cache.time_to_full =
-					bq27x00_battery_read_time(di,
-							BQ27x00_REG_TTF);
-			}
-			cache.charge_full = bq27x00_battery_read_lmd(di);
-			cache.health = bq27x00_battery_read_health(di);
-		}
-		cache.temperature = bq27x00_battery_read_temperature(di);
-		if (!is_bq27425)
-			cache.cycle_count = bq27x00_battery_read_cyct(di);
-		if (is_bq27742)
-			cache.power_avg =
-				bq27x00_battery_read_pwr_avg(di,
-						BQ27742_POWER_AVG);
-		else
-			cache.power_avg =
-				bq27x00_battery_read_pwr_avg(di,
-						BQ27x00_POWER_AVG);
-
-		/* We only have to read charge design full once */
-		if (di->charge_design_full <= 0)
-			di->charge_design_full = bq27x00_battery_read_ilmd(di);
-	}
-
-	if (di->cache.capacity != cache.capacity)
-		power_supply_changed(di->bat);
-
-	if (memcmp(&di->cache, &cache, sizeof(cache)) != 0)
-		di->cache = cache;
-
-	di->last_update = jiffies;
-}
-
-static void bq27x00_battery_poll(struct work_struct *work)
-{
-	struct bq27x00_device_info *di =
-		container_of(work, struct bq27x00_device_info, work.work);
-
-	bq27x00_update(di);
-
-	if (poll_interval > 0) {
-		/* The timer does not have to be accurate. */
-		set_timer_slack(&di->work.timer, poll_interval * HZ / 4);
-		schedule_delayed_work(&di->work, poll_interval * HZ);
-	}
-}
-
-/*
- * Return the battery average current in µA
- * Note that current can be negative signed as well
- * Or 0 if something fails.
- */
-static int bq27x00_battery_current(struct bq27x00_device_info *di,
-				   union power_supply_propval *val)
-{
-	int curr;
-	int flags;
-
-	curr = bq27x00_read(di, BQ27x00_REG_AI, false);
-	if (curr < 0) {
-		dev_err(di->dev, "error reading current\n");
-		return curr;
-	}
-
-	if (bq27xxx_is_chip_version_higher(di)) {
-		/* bq27500 returns signed value */
-		val->intval = (int)((s16)curr) * 1000;
-	} else {
-		flags = bq27x00_read(di, BQ27x00_REG_FLAGS, false);
-		if (flags & BQ27000_FLAG_CHGS) {
-			dev_dbg(di->dev, "negative current!\n");
-			curr = -curr;
-		}
-
-		val->intval = curr * 3570 / BQ27000_RS;
-	}
-
-	return 0;
-}
-
-static int bq27x00_battery_status(struct bq27x00_device_info *di,
-				  union power_supply_propval *val)
-{
-	int status;
-
-	if (bq27xxx_is_chip_version_higher(di)) {
-		if (di->cache.flags & BQ27500_FLAG_FC)
-			status = POWER_SUPPLY_STATUS_FULL;
-		else if (di->cache.flags & BQ27500_FLAG_DSC)
-			status = POWER_SUPPLY_STATUS_DISCHARGING;
-		else
-			status = POWER_SUPPLY_STATUS_CHARGING;
-	} else {
-		if (di->cache.flags & BQ27000_FLAG_FC)
-			status = POWER_SUPPLY_STATUS_FULL;
-		else if (di->cache.flags & BQ27000_FLAG_CHGS)
-			status = POWER_SUPPLY_STATUS_CHARGING;
-		else if (power_supply_am_i_supplied(di->bat))
-			status = POWER_SUPPLY_STATUS_NOT_CHARGING;
-		else
-			status = POWER_SUPPLY_STATUS_DISCHARGING;
-	}
-
-	val->intval = status;
-
-	return 0;
-}
-
-static int bq27x00_battery_capacity_level(struct bq27x00_device_info *di,
-					  union power_supply_propval *val)
-{
-	int level;
-
-	if (bq27xxx_is_chip_version_higher(di)) {
-		if (di->cache.flags & BQ27500_FLAG_FC)
-			level = POWER_SUPPLY_CAPACITY_LEVEL_FULL;
-		else if (di->cache.flags & BQ27500_FLAG_SOC1)
-			level = POWER_SUPPLY_CAPACITY_LEVEL_LOW;
-		else if (di->cache.flags & BQ27500_FLAG_SOCF)
-			level = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL;
-		else
-			level = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL;
-	} else {
-		if (di->cache.flags & BQ27000_FLAG_FC)
-			level = POWER_SUPPLY_CAPACITY_LEVEL_FULL;
-		else if (di->cache.flags & BQ27000_FLAG_EDV1)
-			level = POWER_SUPPLY_CAPACITY_LEVEL_LOW;
-		else if (di->cache.flags & BQ27000_FLAG_EDVF)
-			level = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL;
-		else
-			level = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL;
-	}
-
-	val->intval = level;
-
-	return 0;
-}
-
-/*
- * Return the battery Voltage in millivolts
- * Or < 0 if something fails.
- */
-static int bq27x00_battery_voltage(struct bq27x00_device_info *di,
-				   union power_supply_propval *val)
-{
-	int volt;
-
-	volt = bq27x00_read(di, BQ27x00_REG_VOLT, false);
-	if (volt < 0) {
-		dev_err(di->dev, "error reading voltage\n");
-		return volt;
-	}
-
-	val->intval = volt * 1000;
-
-	return 0;
-}
-
-static int bq27x00_simple_value(int value,
-				union power_supply_propval *val)
-{
-	if (value < 0)
-		return value;
-
-	val->intval = value;
-
-	return 0;
-}
-
-static int bq27x00_battery_get_property(struct power_supply *psy,
-					enum power_supply_property psp,
-					union power_supply_propval *val)
-{
-	int ret = 0;
-	struct bq27x00_device_info *di = power_supply_get_drvdata(psy);
-
-	mutex_lock(&di->lock);
-	if (time_is_before_jiffies(di->last_update + 5 * HZ)) {
-		cancel_delayed_work_sync(&di->work);
-		bq27x00_battery_poll(&di->work.work);
-	}
-	mutex_unlock(&di->lock);
-
-	if (psp != POWER_SUPPLY_PROP_PRESENT && di->cache.flags < 0)
-		return -ENODEV;
-
-	switch (psp) {
-	case POWER_SUPPLY_PROP_STATUS:
-		ret = bq27x00_battery_status(di, val);
-		break;
-	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
-		ret = bq27x00_battery_voltage(di, val);
-		break;
-	case POWER_SUPPLY_PROP_PRESENT:
-		val->intval = di->cache.flags < 0 ? 0 : 1;
-		break;
-	case POWER_SUPPLY_PROP_CURRENT_NOW:
-		ret = bq27x00_battery_current(di, val);
-		break;
-	case POWER_SUPPLY_PROP_CAPACITY:
-		ret = bq27x00_simple_value(di->cache.capacity, val);
-		break;
-	case POWER_SUPPLY_PROP_CAPACITY_LEVEL:
-		ret = bq27x00_battery_capacity_level(di, val);
-		break;
-	case POWER_SUPPLY_PROP_TEMP:
-		ret = bq27x00_simple_value(di->cache.temperature, val);
-		if (ret == 0)
-			val->intval -= 2731;
-		break;
-	case POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW:
-		ret = bq27x00_simple_value(di->cache.time_to_empty, val);
-		break;
-	case POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG:
-		ret = bq27x00_simple_value(di->cache.time_to_empty_avg, val);
-		break;
-	case POWER_SUPPLY_PROP_TIME_TO_FULL_NOW:
-		ret = bq27x00_simple_value(di->cache.time_to_full, val);
-		break;
-	case POWER_SUPPLY_PROP_TECHNOLOGY:
-		val->intval = POWER_SUPPLY_TECHNOLOGY_LION;
-		break;
-	case POWER_SUPPLY_PROP_CHARGE_NOW:
-		ret = bq27x00_simple_value(bq27x00_battery_read_nac(di), val);
-		break;
-	case POWER_SUPPLY_PROP_CHARGE_FULL:
-		ret = bq27x00_simple_value(di->cache.charge_full, val);
-		break;
-	case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
-		ret = bq27x00_simple_value(di->charge_design_full, val);
-		break;
-	case POWER_SUPPLY_PROP_CYCLE_COUNT:
-		ret = bq27x00_simple_value(di->cache.cycle_count, val);
-		break;
-	case POWER_SUPPLY_PROP_ENERGY_NOW:
-		ret = bq27x00_simple_value(di->cache.energy, val);
-		break;
-	case POWER_SUPPLY_PROP_POWER_AVG:
-		ret = bq27x00_simple_value(di->cache.power_avg, val);
-		break;
-	case POWER_SUPPLY_PROP_HEALTH:
-		ret = bq27x00_simple_value(di->cache.health, val);
-		break;
-	case POWER_SUPPLY_PROP_MANUFACTURER:
-		val->strval = BQ27XXX_MANUFACTURER;
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	return ret;
-}
-
-static void bq27x00_external_power_changed(struct power_supply *psy)
-{
-	struct bq27x00_device_info *di = power_supply_get_drvdata(psy);
-
-	cancel_delayed_work_sync(&di->work);
-	schedule_delayed_work(&di->work, 0);
-}
-
-static int bq27x00_powersupply_init(struct bq27x00_device_info *di,
-				    const char *name)
-{
-	int ret;
-	struct power_supply_desc *psy_desc;
-	struct power_supply_config psy_cfg = { .drv_data = di, };
-
-	psy_desc = devm_kzalloc(di->dev, sizeof(*psy_desc), GFP_KERNEL);
-	if (!psy_desc)
-		return -ENOMEM;
-
-	psy_desc->name = name;
-	psy_desc->type = POWER_SUPPLY_TYPE_BATTERY;
-	if (di->chip == BQ27425) {
-		psy_desc->properties = bq27425_battery_props;
-		psy_desc->num_properties = ARRAY_SIZE(bq27425_battery_props);
-	} else if (di->chip == BQ27742) {
-		psy_desc->properties = bq27742_battery_props;
-		psy_desc->num_properties = ARRAY_SIZE(bq27742_battery_props);
-	} else if (di->chip == BQ27510) {
-		psy_desc->properties = bq27510_battery_props;
-		psy_desc->num_properties = ARRAY_SIZE(bq27510_battery_props);
-	} else {
-		psy_desc->properties = bq27x00_battery_props;
-		psy_desc->num_properties = ARRAY_SIZE(bq27x00_battery_props);
-	}
-	psy_desc->get_property = bq27x00_battery_get_property;
-	psy_desc->external_power_changed = bq27x00_external_power_changed;
-
-	INIT_DELAYED_WORK(&di->work, bq27x00_battery_poll);
-	mutex_init(&di->lock);
-
-	di->bat = power_supply_register_no_ws(di->dev, psy_desc, &psy_cfg);
-	if (IS_ERR(di->bat)) {
-		ret = PTR_ERR(di->bat);
-		dev_err(di->dev, "failed to register battery: %d\n", ret);
-		return ret;
-	}
-
-	dev_info(di->dev, "support ver. %s enabled\n", DRIVER_VERSION);
-
-	bq27x00_update(di);
-
-	return 0;
-}
-
-static void bq27x00_powersupply_unregister(struct bq27x00_device_info *di)
-{
-	/*
-	 * power_supply_unregister call bq27x00_battery_get_property which
-	 * call bq27x00_battery_poll.
-	 * Make sure that bq27x00_battery_poll will not call
-	 * schedule_delayed_work again after unregister (which cause OOPS).
-	 */
-	poll_interval = 0;
-
-	cancel_delayed_work_sync(&di->work);
-
-	power_supply_unregister(di->bat);
-
-	mutex_destroy(&di->lock);
-}
-
-/* i2c specific code */
-#ifdef CONFIG_BATTERY_BQ27X00_I2C
-
-/* If the system has several batteries we need a different name for each
- * of them...
- */
-static DEFINE_IDR(battery_id);
-static DEFINE_MUTEX(battery_mutex);
-
-static int bq27x00_read_i2c(struct bq27x00_device_info *di, u8 reg, bool single)
-{
-	struct i2c_client *client = to_i2c_client(di->dev);
-	struct i2c_msg msg[2];
-	unsigned char data[2];
-	int ret;
-
-	if (!client->adapter)
-		return -ENODEV;
-
-	msg[0].addr = client->addr;
-	msg[0].flags = 0;
-	msg[0].buf = &reg;
-	msg[0].len = sizeof(reg);
-	msg[1].addr = client->addr;
-	msg[1].flags = I2C_M_RD;
-	msg[1].buf = data;
-	if (single)
-		msg[1].len = 1;
-	else
-		msg[1].len = 2;
-
-	ret = i2c_transfer(client->adapter, msg, ARRAY_SIZE(msg));
-	if (ret < 0)
-		return ret;
-
-	if (!single)
-		ret = get_unaligned_le16(data);
-	else
-		ret = data[0];
-
-	return ret;
-}
-
-static int bq27x00_battery_probe(struct i2c_client *client,
-				 const struct i2c_device_id *id)
-{
-	char *name;
-	struct bq27x00_device_info *di;
-	int num;
-	int retval = 0;
-
-	/* Get new ID for the new battery device */
-	mutex_lock(&battery_mutex);
-	num = idr_alloc(&battery_id, client, 0, 0, GFP_KERNEL);
-	mutex_unlock(&battery_mutex);
-	if (num < 0)
-		return num;
-
-	name = devm_kasprintf(&client->dev, GFP_KERNEL, "%s-%d", id->name, num);
-	if (!name) {
-		retval = -ENOMEM;
-		goto batt_failed;
-	}
-
-	di = devm_kzalloc(&client->dev, sizeof(*di), GFP_KERNEL);
-	if (!di) {
-		retval = -ENOMEM;
-		goto batt_failed;
-	}
-
-	di->id = num;
-	di->dev = &client->dev;
-	di->chip = id->driver_data;
-	di->bus.read = &bq27x00_read_i2c;
-
-	retval = bq27x00_powersupply_init(di, name);
-	if (retval)
-		goto batt_failed;
-
-	i2c_set_clientdata(client, di);
-
-	return 0;
-
-batt_failed:
-	mutex_lock(&battery_mutex);
-	idr_remove(&battery_id, num);
-	mutex_unlock(&battery_mutex);
-
-	return retval;
-}
-
-static int bq27x00_battery_remove(struct i2c_client *client)
-{
-	struct bq27x00_device_info *di = i2c_get_clientdata(client);
-
-	bq27x00_powersupply_unregister(di);
-
-	mutex_lock(&battery_mutex);
-	idr_remove(&battery_id, di->id);
-	mutex_unlock(&battery_mutex);
-
-	return 0;
-}
-
-static const struct i2c_device_id bq27x00_id[] = {
-	{ "bq27200", BQ27000 },	/* bq27200 is same as bq27000, but with i2c */
-	{ "bq27500", BQ27500 },
-	{ "bq27425", BQ27425 },
-	{ "bq27742", BQ27742 },
-	{ "bq27510", BQ27510 },
-	{},
-};
-MODULE_DEVICE_TABLE(i2c, bq27x00_id);
-
-static struct i2c_driver bq27x00_battery_driver = {
-	.driver = {
-		.name = "bq27x00-battery",
-	},
-	.probe = bq27x00_battery_probe,
-	.remove = bq27x00_battery_remove,
-	.id_table = bq27x00_id,
-};
-
-static inline int bq27x00_battery_i2c_init(void)
-{
-	int ret = i2c_add_driver(&bq27x00_battery_driver);
-
-	if (ret)
-		pr_err("Unable to register BQ27x00 i2c driver\n");
-
-	return ret;
-}
-
-static inline void bq27x00_battery_i2c_exit(void)
-{
-	i2c_del_driver(&bq27x00_battery_driver);
-}
-
-#else
-
-static inline int bq27x00_battery_i2c_init(void) { return 0; }
-static inline void bq27x00_battery_i2c_exit(void) {};
-
-#endif
-
-/* platform specific code */
-#ifdef CONFIG_BATTERY_BQ27X00_PLATFORM
-
-static int bq27000_read_platform(struct bq27x00_device_info *di, u8 reg,
-				 bool single)
-{
-	struct device *dev = di->dev;
-	struct bq27000_platform_data *pdata = dev->platform_data;
-	unsigned int timeout = 3;
-	int upper, lower;
-	int temp;
-
-	if (!single) {
-		/* Make sure the value has not changed in between reading the
-		 * lower and the upper part */
-		upper = pdata->read(dev, reg + 1);
-		do {
-			temp = upper;
-			if (upper < 0)
-				return upper;
-
-			lower = pdata->read(dev, reg);
-			if (lower < 0)
-				return lower;
-
-			upper = pdata->read(dev, reg + 1);
-		} while (temp != upper && --timeout);
-
-		if (timeout == 0)
-			return -EIO;
-
-		return (upper << 8) | lower;
-	}
-
-	return pdata->read(dev, reg);
-}
-
-static int bq27000_battery_probe(struct platform_device *pdev)
-{
-	struct bq27x00_device_info *di;
-	struct bq27000_platform_data *pdata = pdev->dev.platform_data;
-	const char *name;
-
-	if (!pdata) {
-		dev_err(&pdev->dev, "no platform_data supplied\n");
-		return -EINVAL;
-	}
-
-	if (!pdata->read) {
-		dev_err(&pdev->dev, "no hdq read callback supplied\n");
-		return -EINVAL;
-	}
-
-	di = devm_kzalloc(&pdev->dev, sizeof(*di), GFP_KERNEL);
-	if (!di)
-		return -ENOMEM;
-
-	platform_set_drvdata(pdev, di);
-
-	di->dev = &pdev->dev;
-	di->chip = BQ27000;
-
-	name = pdata->name ?: dev_name(&pdev->dev);
-	di->bus.read = &bq27000_read_platform;
-
-	return bq27x00_powersupply_init(di, name);
-}
-
-static int bq27000_battery_remove(struct platform_device *pdev)
-{
-	struct bq27x00_device_info *di = platform_get_drvdata(pdev);
-
-	bq27x00_powersupply_unregister(di);
-
-	return 0;
-}
-
-static struct platform_driver bq27000_battery_driver = {
-	.probe	= bq27000_battery_probe,
-	.remove = bq27000_battery_remove,
-	.driver = {
-		.name = "bq27000-battery",
-	},
-};
-
-static inline int bq27x00_battery_platform_init(void)
-{
-	int ret = platform_driver_register(&bq27000_battery_driver);
-
-	if (ret)
-		pr_err("Unable to register BQ27000 platform driver\n");
-
-	return ret;
-}
-
-static inline void bq27x00_battery_platform_exit(void)
-{
-	platform_driver_unregister(&bq27000_battery_driver);
-}
-
-#else
-
-static inline int bq27x00_battery_platform_init(void) { return 0; }
-static inline void bq27x00_battery_platform_exit(void) {};
-
-#endif
-
-/*
- * Module stuff
- */
-
-static int __init bq27x00_battery_init(void)
-{
-	int ret;
-
-	ret = bq27x00_battery_i2c_init();
-	if (ret)
-		return ret;
-
-	ret = bq27x00_battery_platform_init();
-	if (ret)
-		bq27x00_battery_i2c_exit();
-
-	return ret;
-}
-module_init(bq27x00_battery_init);
-
-static void __exit bq27x00_battery_exit(void)
-{
-	bq27x00_battery_platform_exit();
-	bq27x00_battery_i2c_exit();
-}
-module_exit(bq27x00_battery_exit);
-
-#ifdef CONFIG_BATTERY_BQ27X00_PLATFORM
-MODULE_ALIAS("platform:bq27000-battery");
-#endif
-
-#ifdef CONFIG_BATTERY_BQ27X00_I2C
-MODULE_ALIAS("i2c:bq27000-battery");
-#endif
-
-MODULE_AUTHOR("Rodolfo Giometti <giometti@linux.it>");
-MODULE_DESCRIPTION("BQ27x00 battery monitor driver");
-MODULE_LICENSE("GPL");
diff --git a/drivers/power/bq27xxx_battery.c b/drivers/power/bq27xxx_battery.c
new file mode 100644
index 0000000..880233c
--- /dev/null
+++ b/drivers/power/bq27xxx_battery.c
@@ -0,0 +1,1375 @@
+/*
+ * BQ27xxx battery driver
+ *
+ * Copyright (C) 2008 Rodolfo Giometti <giometti@linux.it>
+ * Copyright (C) 2008 Eurotech S.p.A. <info@eurotech.it>
+ * Copyright (C) 2010-2011 Lars-Peter Clausen <lars@metafoo.de>
+ * Copyright (C) 2011 Pali Rohár <pali.rohar@gmail.com>
+ *
+ * Based on a previous work by Copyright (C) 2008 Texas Instruments, Inc.
+ *
+ * This package is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
+ * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.
+ *
+ * Datasheets:
+ * http://www.ti.com/product/bq27000
+ * http://www.ti.com/product/bq27200
+ * http://www.ti.com/product/bq27010
+ * http://www.ti.com/product/bq27210
+ * http://www.ti.com/product/bq27500
+ * http://www.ti.com/product/bq27510-g3
+ * http://www.ti.com/product/bq27520-g4
+ * http://www.ti.com/product/bq27530-g1
+ * http://www.ti.com/product/bq27531-g1
+ * http://www.ti.com/product/bq27541-g1
+ * http://www.ti.com/product/bq27542-g1
+ * http://www.ti.com/product/bq27546-g1
+ * http://www.ti.com/product/bq27742-g1
+ * http://www.ti.com/product/bq27545-g1
+ * http://www.ti.com/product/bq27421-g1
+ * http://www.ti.com/product/bq27425-g1
+ * http://www.ti.com/product/bq27411-g1
+ * http://www.ti.com/product/bq27621-g1
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/param.h>
+#include <linux/jiffies.h>
+#include <linux/workqueue.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/idr.h>
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <asm/unaligned.h>
+
+#include <linux/power/bq27xxx_battery.h>
+
+#define DRIVER_VERSION		"1.2.0"
+
+#define BQ27XXX_MANUFACTURER	"Texas Instruments"
+
+/* BQ27XXX Flags */
+#define BQ27XXX_FLAG_DSC	BIT(0)
+#define BQ27XXX_FLAG_SOCF	BIT(1) /* State-of-Charge threshold final */
+#define BQ27XXX_FLAG_SOC1	BIT(2) /* State-of-Charge threshold 1 */
+#define BQ27XXX_FLAG_FC		BIT(9)
+#define BQ27XXX_FLAG_OTD	BIT(14)
+#define BQ27XXX_FLAG_OTC	BIT(15)
+#define BQ27XXX_FLAG_UT		BIT(14)
+#define BQ27XXX_FLAG_OT		BIT(15)
+
+/* BQ27000 has different layout for Flags register */
+#define BQ27000_FLAG_EDVF	BIT(0) /* Final End-of-Discharge-Voltage flag */
+#define BQ27000_FLAG_EDV1	BIT(1) /* First End-of-Discharge-Voltage flag */
+#define BQ27000_FLAG_CI		BIT(4) /* Capacity Inaccurate flag */
+#define BQ27000_FLAG_FC		BIT(5)
+#define BQ27000_FLAG_CHGS	BIT(7) /* Charge state flag */
+
+#define BQ27XXX_RS			(20) /* Resistor sense mOhm */
+#define BQ27XXX_POWER_CONSTANT		(29200) /* 29.2 µV^2 * 1000 */
+#define BQ27XXX_CURRENT_CONSTANT	(3570) /* 3.57 µV * 1000 */
+
+struct bq27xxx_device_info;
+struct bq27xxx_access_methods {
+	int (*read)(struct bq27xxx_device_info *di, u8 reg, bool single);
+};
+
+#define INVALID_REG_ADDR	0xff
+
+/*
+ * bq27xxx_reg_index - Register names
+ *
+ * These are indexes into a device's register mapping array.
+ */
+enum bq27xxx_reg_index {
+	BQ27XXX_REG_CTRL = 0,	/* Control */
+	BQ27XXX_REG_TEMP,	/* Temperature */
+	BQ27XXX_REG_INT_TEMP,	/* Internal Temperature */
+	BQ27XXX_REG_VOLT,	/* Voltage */
+	BQ27XXX_REG_AI,		/* Average Current */
+	BQ27XXX_REG_FLAGS,	/* Flags */
+	BQ27XXX_REG_TTE,	/* Time-to-Empty */
+	BQ27XXX_REG_TTF,	/* Time-to-Full */
+	BQ27XXX_REG_TTES,	/* Time-to-Empty Standby */
+	BQ27XXX_REG_TTECP,	/* Time-to-Empty at Constant Power */
+	BQ27XXX_REG_NAC,	/* Nominal Available Capacity */
+	BQ27XXX_REG_FCC,	/* Full Charge Capacity */
+	BQ27XXX_REG_CYCT,	/* Cycle Count */
+	BQ27XXX_REG_AE,		/* Available Energy */
+	BQ27XXX_REG_SOC,	/* State-of-Charge */
+	BQ27XXX_REG_DCAP,	/* Design Capacity */
+	BQ27XXX_REG_AP,		/* Average Power */
+};
+
+struct bq27xxx_reg_cache {
+	int temperature;
+	int time_to_empty;
+	int time_to_empty_avg;
+	int time_to_full;
+	int charge_full;
+	int cycle_count;
+	int capacity;
+	int energy;
+	int flags;
+	int power_avg;
+	int health;
+};
+
+struct bq27xxx_device_info {
+	struct device		*dev;
+	int			id;
+	enum bq27xxx_chip	chip;
+
+	struct bq27xxx_reg_cache cache;
+	int charge_design_full;
+
+	unsigned long last_update;
+	struct delayed_work work;
+
+	struct power_supply	*bat;
+
+	struct bq27xxx_access_methods bus;
+
+	struct mutex lock;
+
+	u8 *regs;
+};
+
+/* Register mappings */
+static u8 bq27000_regs[] = {
+	0x00,	/* CONTROL	*/
+	0x06,	/* TEMP		*/
+	INVALID_REG_ADDR,	/* INT TEMP - NA*/
+	0x08,	/* VOLT		*/
+	0x14,	/* AVG CURR	*/
+	0x0a,	/* FLAGS	*/
+	0x16,	/* TTE		*/
+	0x18,	/* TTF		*/
+	0x1c,	/* TTES		*/
+	0x26,	/* TTECP	*/
+	0x0c,	/* NAC		*/
+	0x12,	/* LMD(FCC)	*/
+	0x2a,	/* CYCT		*/
+	0x22,	/* AE		*/
+	0x0b,	/* SOC(RSOC)	*/
+	0x76,	/* DCAP(ILMD)	*/
+	0x24,	/* AP		*/
+};
+
+static u8 bq27010_regs[] = {
+	0x00,	/* CONTROL	*/
+	0x06,	/* TEMP		*/
+	INVALID_REG_ADDR,	/* INT TEMP - NA*/
+	0x08,	/* VOLT		*/
+	0x14,	/* AVG CURR	*/
+	0x0a,	/* FLAGS	*/
+	0x16,	/* TTE		*/
+	0x18,	/* TTF		*/
+	0x1c,	/* TTES		*/
+	0x26,	/* TTECP	*/
+	0x0c,	/* NAC		*/
+	0x12,	/* LMD(FCC)	*/
+	0x2a,	/* CYCT		*/
+	INVALID_REG_ADDR,	/* AE - NA	*/
+	0x0b,	/* SOC(RSOC)	*/
+	0x76,	/* DCAP(ILMD)	*/
+	INVALID_REG_ADDR,	/* AP - NA	*/
+};
+
+static u8 bq27500_regs[] = {
+	0x00,	/* CONTROL	*/
+	0x06,	/* TEMP		*/
+	0x28,	/* INT TEMP	*/
+	0x08,	/* VOLT		*/
+	0x14,	/* AVG CURR	*/
+	0x0a,	/* FLAGS	*/
+	0x16,	/* TTE		*/
+	INVALID_REG_ADDR,	/* TTF - NA	*/
+	0x1a,	/* TTES		*/
+	INVALID_REG_ADDR,	/* TTECP - NA	*/
+	0x0c,	/* NAC		*/
+	0x12,	/* LMD(FCC)	*/
+	0x1e,	/* CYCT		*/
+	INVALID_REG_ADDR,	/* AE - NA	*/
+	0x20,	/* SOC(RSOC)	*/
+	0x2e,	/* DCAP(ILMD)	*/
+	INVALID_REG_ADDR,	/* AP - NA	*/
+};
+
+static u8 bq27530_regs[] = {
+	0x00,	/* CONTROL	*/
+	0x06,	/* TEMP		*/
+	0x32,	/* INT TEMP	*/
+	0x08,	/* VOLT		*/
+	0x14,	/* AVG CURR	*/
+	0x0a,	/* FLAGS	*/
+	0x16,	/* TTE		*/
+	INVALID_REG_ADDR,	/* TTF - NA	*/
+	INVALID_REG_ADDR,	/* TTES - NA	*/
+	INVALID_REG_ADDR,	/* TTECP - NA	*/
+	0x0c,	/* NAC		*/
+	0x12,	/* LMD(FCC)	*/
+	0x2a,	/* CYCT		*/
+	INVALID_REG_ADDR,	/* AE - NA	*/
+	0x2c,	/* SOC(RSOC)	*/
+	INVALID_REG_ADDR,	/* DCAP - NA	*/
+	0x24,	/* AP		*/
+};
+
+static u8 bq27541_regs[] = {
+	0x00,	/* CONTROL	*/
+	0x06,	/* TEMP		*/
+	0x28,	/* INT TEMP	*/
+	0x08,	/* VOLT		*/
+	0x14,	/* AVG CURR	*/
+	0x0a,	/* FLAGS	*/
+	0x16,	/* TTE		*/
+	INVALID_REG_ADDR,	/* TTF - NA	*/
+	INVALID_REG_ADDR,	/* TTES - NA	*/
+	INVALID_REG_ADDR,	/* TTECP - NA	*/
+	0x0c,	/* NAC		*/
+	0x12,	/* LMD(FCC)	*/
+	0x2a,	/* CYCT		*/
+	INVALID_REG_ADDR,	/* AE - NA	*/
+	0x2c,	/* SOC(RSOC)	*/
+	0x3c,	/* DCAP		*/
+	0x76,	/* AP		*/
+};
+
+static u8 bq27545_regs[] = {
+	0x00,	/* CONTROL	*/
+	0x06,	/* TEMP		*/
+	0x28,	/* INT TEMP	*/
+	0x08,	/* VOLT		*/
+	0x14,	/* AVG CURR	*/
+	0x0a,	/* FLAGS	*/
+	0x16,	/* TTE		*/
+	INVALID_REG_ADDR,	/* TTF - NA	*/
+	INVALID_REG_ADDR,	/* TTES - NA	*/
+	INVALID_REG_ADDR,	/* TTECP - NA	*/
+	0x0c,	/* NAC		*/
+	0x12,	/* LMD(FCC)	*/
+	0x2a,	/* CYCT		*/
+	INVALID_REG_ADDR,	/* AE - NA	*/
+	0x2c,	/* SOC(RSOC)	*/
+	INVALID_REG_ADDR,	/* DCAP - NA */
+	0x24,	/* AP		*/
+};
+
+static u8 bq27421_regs[] = {
+	0x00,	/* CONTROL	*/
+	0x02,	/* TEMP		*/
+	0x1e,	/* INT TEMP	*/
+	0x04,	/* VOLT		*/
+	0x10,	/* AVG CURR	*/
+	0x06,	/* FLAGS	*/
+	INVALID_REG_ADDR,	/* TTE - NA	*/
+	INVALID_REG_ADDR,	/* TTF - NA	*/
+	INVALID_REG_ADDR,	/* TTES - NA	*/
+	INVALID_REG_ADDR,	/* TTECP - NA	*/
+	0x08,	/* NAC		*/
+	0x0e,	/* FCC		*/
+	INVALID_REG_ADDR,	/* CYCT - NA	*/
+	INVALID_REG_ADDR,	/* AE - NA	*/
+	0x1c,	/* SOC		*/
+	0x3c,	/* DCAP		*/
+	0x18,	/* AP		*/
+};
+
+static u8 *bq27xxx_regs[] = {
+	[BQ27000] = bq27000_regs,
+	[BQ27010] = bq27010_regs,
+	[BQ27500] = bq27500_regs,
+	[BQ27530] = bq27530_regs,
+	[BQ27541] = bq27541_regs,
+	[BQ27545] = bq27545_regs,
+	[BQ27421] = bq27421_regs,
+};
+
+static enum power_supply_property bq27000_battery_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
+	POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG,
+	POWER_SUPPLY_PROP_TIME_TO_FULL_NOW,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_NOW,
+	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
+	POWER_SUPPLY_PROP_CYCLE_COUNT,
+	POWER_SUPPLY_PROP_ENERGY_NOW,
+	POWER_SUPPLY_PROP_POWER_AVG,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+static enum power_supply_property bq27010_battery_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
+	POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG,
+	POWER_SUPPLY_PROP_TIME_TO_FULL_NOW,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_NOW,
+	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
+	POWER_SUPPLY_PROP_CYCLE_COUNT,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+static enum power_supply_property bq27500_battery_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_NOW,
+	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
+	POWER_SUPPLY_PROP_CYCLE_COUNT,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+static enum power_supply_property bq27530_battery_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_NOW,
+	POWER_SUPPLY_PROP_POWER_AVG,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_CYCLE_COUNT,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+static enum power_supply_property bq27541_battery_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_NOW,
+	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
+	POWER_SUPPLY_PROP_CYCLE_COUNT,
+	POWER_SUPPLY_PROP_POWER_AVG,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+static enum power_supply_property bq27545_battery_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_NOW,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_CYCLE_COUNT,
+	POWER_SUPPLY_PROP_POWER_AVG,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+static enum power_supply_property bq27421_battery_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_NOW,
+	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+#define BQ27XXX_PROP(_id, _prop)		\
+	[_id] = {				\
+		.props = _prop,			\
+		.size = ARRAY_SIZE(_prop),	\
+	}
+
+static struct {
+	enum power_supply_property *props;
+	size_t size;
+} bq27xxx_battery_props[] = {
+	BQ27XXX_PROP(BQ27000, bq27000_battery_props),
+	BQ27XXX_PROP(BQ27010, bq27010_battery_props),
+	BQ27XXX_PROP(BQ27500, bq27500_battery_props),
+	BQ27XXX_PROP(BQ27530, bq27530_battery_props),
+	BQ27XXX_PROP(BQ27541, bq27541_battery_props),
+	BQ27XXX_PROP(BQ27545, bq27545_battery_props),
+	BQ27XXX_PROP(BQ27421, bq27421_battery_props),
+};
+
+static unsigned int poll_interval = 360;
+module_param(poll_interval, uint, 0644);
+MODULE_PARM_DESC(poll_interval,
+		 "battery poll interval in seconds - 0 disables polling");
+
+/*
+ * Common code for BQ27xxx devices
+ */
+
+static inline int bq27xxx_read(struct bq27xxx_device_info *di, int reg_index,
+			       bool single)
+{
+	/* Reports EINVAL for invalid/missing registers */
+	if (!di || di->regs[reg_index] == INVALID_REG_ADDR)
+		return -EINVAL;
+
+	return di->bus.read(di, di->regs[reg_index], single);
+}
+
+/*
+ * Return the battery State-of-Charge
+ * Or < 0 if something fails.
+ */
+static int bq27xxx_battery_read_soc(struct bq27xxx_device_info *di)
+{
+	int soc;
+
+	soc = bq27xxx_read(di, BQ27XXX_REG_SOC, false);
+
+	if (soc < 0)
+		dev_dbg(di->dev, "error reading State-of-Charge\n");
+
+	return soc;
+}
+
+/*
+ * Return a battery charge value in µAh
+ * Or < 0 if something fails.
+ */
+static int bq27xxx_battery_read_charge(struct bq27xxx_device_info *di, u8 reg)
+{
+	int charge;
+
+	charge = bq27xxx_read(di, reg, false);
+	if (charge < 0) {
+		dev_dbg(di->dev, "error reading charge register %02x: %d\n",
+			reg, charge);
+		return charge;
+	}
+
+	if (di->chip == BQ27000 || di->chip == BQ27010)
+		charge *= BQ27XXX_CURRENT_CONSTANT / BQ27XXX_RS;
+	else
+		charge *= 1000;
+
+	return charge;
+}
+
+/*
+ * Return the battery Nominal available capacity in µAh
+ * Or < 0 if something fails.
+ */
+static inline int bq27xxx_battery_read_nac(struct bq27xxx_device_info *di)
+{
+	int flags;
+
+	if (di->chip == BQ27000 || di->chip == BQ27010) {
+		flags = bq27xxx_read(di, BQ27XXX_REG_FLAGS, true);
+		if (flags >= 0 && (flags & BQ27000_FLAG_CI))
+			return -ENODATA;
+	}
+
+	return bq27xxx_battery_read_charge(di, BQ27XXX_REG_NAC);
+}
+
+/*
+ * Return the battery Full Charge Capacity in µAh
+ * Or < 0 if something fails.
+ */
+static inline int bq27xxx_battery_read_fcc(struct bq27xxx_device_info *di)
+{
+	return bq27xxx_battery_read_charge(di, BQ27XXX_REG_FCC);
+}
+
+/*
+ * Return the Design Capacity in µAh
+ * Or < 0 if something fails.
+ */
+static int bq27xxx_battery_read_dcap(struct bq27xxx_device_info *di)
+{
+	int dcap;
+
+	dcap = bq27xxx_read(di, BQ27XXX_REG_DCAP, false);
+
+	if (dcap < 0) {
+		dev_dbg(di->dev, "error reading initial last measured discharge\n");
+		return dcap;
+	}
+
+	if (di->chip == BQ27000 || di->chip == BQ27010)
+		dcap *= BQ27XXX_CURRENT_CONSTANT / BQ27XXX_RS;
+	else
+		dcap *= 1000;
+
+	return dcap;
+}
+
+/*
+ * Return the battery Available energy in µWh
+ * Or < 0 if something fails.
+ */
+static int bq27xxx_battery_read_energy(struct bq27xxx_device_info *di)
+{
+	int ae;
+
+	ae = bq27xxx_read(di, BQ27XXX_REG_AE, false);
+	if (ae < 0) {
+		dev_dbg(di->dev, "error reading available energy\n");
+		return ae;
+	}
+
+	if (di->chip == BQ27000 || di->chip == BQ27010)
+		ae *= BQ27XXX_POWER_CONSTANT / BQ27XXX_RS;
+	else
+		ae *= 1000;
+
+	return ae;
+}
+
+/*
+ * Return the battery temperature in tenths of degree Kelvin
+ * Or < 0 if something fails.
+ */
+static int bq27xxx_battery_read_temperature(struct bq27xxx_device_info *di)
+{
+	int temp;
+
+	temp = bq27xxx_read(di, BQ27XXX_REG_TEMP, false);
+	if (temp < 0) {
+		dev_err(di->dev, "error reading temperature\n");
+		return temp;
+	}
+
+	if (di->chip == BQ27000 || di->chip == BQ27010)
+		temp = 5 * temp / 2;
+
+	return temp;
+}
+
+/*
+ * Return the battery Cycle count total
+ * Or < 0 if something fails.
+ */
+static int bq27xxx_battery_read_cyct(struct bq27xxx_device_info *di)
+{
+	int cyct;
+
+	cyct = bq27xxx_read(di, BQ27XXX_REG_CYCT, false);
+	if (cyct < 0)
+		dev_err(di->dev, "error reading cycle count total\n");
+
+	return cyct;
+}
+
+/*
+ * Read a time register.
+ * Return < 0 if something fails.
+ */
+static int bq27xxx_battery_read_time(struct bq27xxx_device_info *di, u8 reg)
+{
+	int tval;
+
+	tval = bq27xxx_read(di, reg, false);
+	if (tval < 0) {
+		dev_dbg(di->dev, "error reading time register %02x: %d\n",
+			reg, tval);
+		return tval;
+	}
+
+	if (tval == 65535)
+		return -ENODATA;
+
+	return tval * 60;
+}
+
+/*
+ * Read an average power register.
+ * Return < 0 if something fails.
+ */
+static int bq27xxx_battery_read_pwr_avg(struct bq27xxx_device_info *di)
+{
+	int tval;
+
+	tval = bq27xxx_read(di, BQ27XXX_REG_AP, false);
+	if (tval < 0) {
+		dev_err(di->dev, "error reading average power register  %02x: %d\n",
+			BQ27XXX_REG_AP, tval);
+		return tval;
+	}
+
+	if (di->chip == BQ27000 || di->chip == BQ27010)
+		return (tval * BQ27XXX_POWER_CONSTANT) / BQ27XXX_RS;
+	else
+		return tval;
+}
+
+/*
+ * Returns true if a battery over temperature condition is detected
+ */
+static bool bq27xxx_battery_overtemp(struct bq27xxx_device_info *di, u16 flags)
+{
+	if (di->chip == BQ27500 || di->chip == BQ27541 || di->chip == BQ27545)
+		return flags & (BQ27XXX_FLAG_OTC | BQ27XXX_FLAG_OTD);
+	if (di->chip == BQ27530 || di->chip == BQ27421)
+		return flags & BQ27XXX_FLAG_OT;
+
+	return false;
+}
+
+/*
+ * Returns true if a battery under temperature condition is detected
+ */
+static bool bq27xxx_battery_undertemp(struct bq27xxx_device_info *di, u16 flags)
+{
+	if (di->chip == BQ27530 || di->chip == BQ27421)
+		return flags & BQ27XXX_FLAG_UT;
+
+	return false;
+}
+
+/*
+ * Returns true if a low state of charge condition is detected
+ */
+static bool bq27xxx_battery_dead(struct bq27xxx_device_info *di, u16 flags)
+{
+	if (di->chip == BQ27000 || di->chip == BQ27010)
+		return flags & (BQ27000_FLAG_EDV1 | BQ27000_FLAG_EDVF);
+	else
+		return flags & (BQ27XXX_FLAG_SOC1 | BQ27XXX_FLAG_SOCF);
+}
+
+/*
+ * Read flag register.
+ * Return < 0 if something fails.
+ */
+static int bq27xxx_battery_read_health(struct bq27xxx_device_info *di)
+{
+	int flags;
+
+	flags = bq27xxx_read(di, BQ27XXX_REG_FLAGS, false);
+	if (flags < 0) {
+		dev_err(di->dev, "error reading flag register:%d\n", flags);
+		return flags;
+	}
+
+	/* Unlikely but important to return first */
+	if (unlikely(bq27xxx_battery_overtemp(di, flags)))
+		return POWER_SUPPLY_HEALTH_OVERHEAT;
+	if (unlikely(bq27xxx_battery_undertemp(di, flags)))
+		return POWER_SUPPLY_HEALTH_COLD;
+	if (unlikely(bq27xxx_battery_dead(di, flags)))
+		return POWER_SUPPLY_HEALTH_DEAD;
+
+	return POWER_SUPPLY_HEALTH_GOOD;
+}
+
+static void bq27xxx_battery_update(struct bq27xxx_device_info *di)
+{
+	struct bq27xxx_reg_cache cache = {0, };
+	bool has_ci_flag = di->chip == BQ27000 || di->chip == BQ27010;
+	bool has_singe_flag = di->chip == BQ27000 || di->chip == BQ27010;
+
+	cache.flags = bq27xxx_read(di, BQ27XXX_REG_FLAGS, has_singe_flag);
+	if ((cache.flags & 0xff) == 0xff)
+		cache.flags = -1; /* read error */
+	if (cache.flags >= 0) {
+		cache.temperature = bq27xxx_battery_read_temperature(di);
+		if (has_ci_flag && (cache.flags & BQ27000_FLAG_CI)) {
+			dev_info(di->dev, "battery is not calibrated! ignoring capacity values\n");
+			cache.capacity = -ENODATA;
+			cache.energy = -ENODATA;
+			cache.time_to_empty = -ENODATA;
+			cache.time_to_empty_avg = -ENODATA;
+			cache.time_to_full = -ENODATA;
+			cache.charge_full = -ENODATA;
+			cache.health = -ENODATA;
+		} else {
+			if (di->regs[BQ27XXX_REG_TTE] != INVALID_REG_ADDR)
+				cache.time_to_empty = bq27xxx_battery_read_time(di, BQ27XXX_REG_TTE);
+			if (di->regs[BQ27XXX_REG_TTECP] != INVALID_REG_ADDR)
+				cache.time_to_empty_avg = bq27xxx_battery_read_time(di, BQ27XXX_REG_TTECP);
+			if (di->regs[BQ27XXX_REG_TTF] != INVALID_REG_ADDR)
+				cache.time_to_full = bq27xxx_battery_read_time(di, BQ27XXX_REG_TTF);
+			cache.charge_full = bq27xxx_battery_read_fcc(di);
+			cache.capacity = bq27xxx_battery_read_soc(di);
+			if (di->regs[BQ27XXX_REG_AE] != INVALID_REG_ADDR)
+				cache.energy = bq27xxx_battery_read_energy(di);
+			cache.health = bq27xxx_battery_read_health(di);
+		}
+		if (di->regs[BQ27XXX_REG_CYCT] != INVALID_REG_ADDR)
+			cache.cycle_count = bq27xxx_battery_read_cyct(di);
+		if (di->regs[BQ27XXX_REG_AP] != INVALID_REG_ADDR)
+			cache.power_avg = bq27xxx_battery_read_pwr_avg(di);
+
+		/* We only have to read charge design full once */
+		if (di->charge_design_full <= 0)
+			di->charge_design_full = bq27xxx_battery_read_dcap(di);
+	}
+
+	if (di->cache.capacity != cache.capacity)
+		power_supply_changed(di->bat);
+
+	if (memcmp(&di->cache, &cache, sizeof(cache)) != 0)
+		di->cache = cache;
+
+	di->last_update = jiffies;
+}
+
+static void bq27xxx_battery_poll(struct work_struct *work)
+{
+	struct bq27xxx_device_info *di =
+			container_of(work, struct bq27xxx_device_info,
+				     work.work);
+
+	bq27xxx_battery_update(di);
+
+	if (poll_interval > 0) {
+		/* The timer does not have to be accurate. */
+		set_timer_slack(&di->work.timer, poll_interval * HZ / 4);
+		schedule_delayed_work(&di->work, poll_interval * HZ);
+	}
+}
+
+/*
+ * Return the battery average current in µA
+ * Note that current can be negative signed as well
+ * Or 0 if something fails.
+ */
+static int bq27xxx_battery_current(struct bq27xxx_device_info *di,
+				   union power_supply_propval *val)
+{
+	int curr;
+	int flags;
+
+	curr = bq27xxx_read(di, BQ27XXX_REG_AI, false);
+	if (curr < 0) {
+		dev_err(di->dev, "error reading current\n");
+		return curr;
+	}
+
+	if (di->chip == BQ27000 || di->chip == BQ27010) {
+		flags = bq27xxx_read(di, BQ27XXX_REG_FLAGS, false);
+		if (flags & BQ27000_FLAG_CHGS) {
+			dev_dbg(di->dev, "negative current!\n");
+			curr = -curr;
+		}
+
+		val->intval = curr * BQ27XXX_CURRENT_CONSTANT / BQ27XXX_RS;
+	} else {
+		/* Other gauges return signed value */
+		val->intval = (int)((s16)curr) * 1000;
+	}
+
+	return 0;
+}
+
+static int bq27xxx_battery_status(struct bq27xxx_device_info *di,
+				  union power_supply_propval *val)
+{
+	int status;
+
+	if (di->chip == BQ27000 || di->chip == BQ27010) {
+		if (di->cache.flags & BQ27000_FLAG_FC)
+			status = POWER_SUPPLY_STATUS_FULL;
+		else if (di->cache.flags & BQ27000_FLAG_CHGS)
+			status = POWER_SUPPLY_STATUS_CHARGING;
+		else if (power_supply_am_i_supplied(di->bat))
+			status = POWER_SUPPLY_STATUS_NOT_CHARGING;
+		else
+			status = POWER_SUPPLY_STATUS_DISCHARGING;
+	} else {
+		if (di->cache.flags & BQ27XXX_FLAG_FC)
+			status = POWER_SUPPLY_STATUS_FULL;
+		else if (di->cache.flags & BQ27XXX_FLAG_DSC)
+			status = POWER_SUPPLY_STATUS_DISCHARGING;
+		else
+			status = POWER_SUPPLY_STATUS_CHARGING;
+	}
+
+	val->intval = status;
+
+	return 0;
+}
+
+static int bq27xxx_battery_capacity_level(struct bq27xxx_device_info *di,
+					  union power_supply_propval *val)
+{
+	int level;
+
+	if (di->chip == BQ27000 || di->chip == BQ27010) {
+		if (di->cache.flags & BQ27000_FLAG_FC)
+			level = POWER_SUPPLY_CAPACITY_LEVEL_FULL;
+		else if (di->cache.flags & BQ27000_FLAG_EDV1)
+			level = POWER_SUPPLY_CAPACITY_LEVEL_LOW;
+		else if (di->cache.flags & BQ27000_FLAG_EDVF)
+			level = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL;
+		else
+			level = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL;
+	} else {
+		if (di->cache.flags & BQ27XXX_FLAG_FC)
+			level = POWER_SUPPLY_CAPACITY_LEVEL_FULL;
+		else if (di->cache.flags & BQ27XXX_FLAG_SOC1)
+			level = POWER_SUPPLY_CAPACITY_LEVEL_LOW;
+		else if (di->cache.flags & BQ27XXX_FLAG_SOCF)
+			level = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL;
+		else
+			level = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL;
+	}
+
+	val->intval = level;
+
+	return 0;
+}
+
+/*
+ * Return the battery Voltage in millivolts
+ * Or < 0 if something fails.
+ */
+static int bq27xxx_battery_voltage(struct bq27xxx_device_info *di,
+				   union power_supply_propval *val)
+{
+	int volt;
+
+	volt = bq27xxx_read(di, BQ27XXX_REG_VOLT, false);
+	if (volt < 0) {
+		dev_err(di->dev, "error reading voltage\n");
+		return volt;
+	}
+
+	val->intval = volt * 1000;
+
+	return 0;
+}
+
+static int bq27xxx_simple_value(int value,
+				union power_supply_propval *val)
+{
+	if (value < 0)
+		return value;
+
+	val->intval = value;
+
+	return 0;
+}
+
+static int bq27xxx_battery_get_property(struct power_supply *psy,
+					enum power_supply_property psp,
+					union power_supply_propval *val)
+{
+	int ret = 0;
+	struct bq27xxx_device_info *di = power_supply_get_drvdata(psy);
+
+	mutex_lock(&di->lock);
+	if (time_is_before_jiffies(di->last_update + 5 * HZ)) {
+		cancel_delayed_work_sync(&di->work);
+		bq27xxx_battery_poll(&di->work.work);
+	}
+	mutex_unlock(&di->lock);
+
+	if (psp != POWER_SUPPLY_PROP_PRESENT && di->cache.flags < 0)
+		return -ENODEV;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_STATUS:
+		ret = bq27xxx_battery_status(di, val);
+		break;
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		ret = bq27xxx_battery_voltage(di, val);
+		break;
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = di->cache.flags < 0 ? 0 : 1;
+		break;
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		ret = bq27xxx_battery_current(di, val);
+		break;
+	case POWER_SUPPLY_PROP_CAPACITY:
+		ret = bq27xxx_simple_value(di->cache.capacity, val);
+		break;
+	case POWER_SUPPLY_PROP_CAPACITY_LEVEL:
+		ret = bq27xxx_battery_capacity_level(di, val);
+		break;
+	case POWER_SUPPLY_PROP_TEMP:
+		ret = bq27xxx_simple_value(di->cache.temperature, val);
+		if (ret == 0)
+			val->intval -= 2731; /* convert decidegree k to c */
+		break;
+	case POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW:
+		ret = bq27xxx_simple_value(di->cache.time_to_empty, val);
+		break;
+	case POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG:
+		ret = bq27xxx_simple_value(di->cache.time_to_empty_avg, val);
+		break;
+	case POWER_SUPPLY_PROP_TIME_TO_FULL_NOW:
+		ret = bq27xxx_simple_value(di->cache.time_to_full, val);
+		break;
+	case POWER_SUPPLY_PROP_TECHNOLOGY:
+		val->intval = POWER_SUPPLY_TECHNOLOGY_LION;
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_NOW:
+		ret = bq27xxx_simple_value(bq27xxx_battery_read_nac(di), val);
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_FULL:
+		ret = bq27xxx_simple_value(di->cache.charge_full, val);
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
+		ret = bq27xxx_simple_value(di->charge_design_full, val);
+		break;
+	case POWER_SUPPLY_PROP_CYCLE_COUNT:
+		ret = bq27xxx_simple_value(di->cache.cycle_count, val);
+		break;
+	case POWER_SUPPLY_PROP_ENERGY_NOW:
+		ret = bq27xxx_simple_value(di->cache.energy, val);
+		break;
+	case POWER_SUPPLY_PROP_POWER_AVG:
+		ret = bq27xxx_simple_value(di->cache.power_avg, val);
+		break;
+	case POWER_SUPPLY_PROP_HEALTH:
+		ret = bq27xxx_simple_value(di->cache.health, val);
+		break;
+	case POWER_SUPPLY_PROP_MANUFACTURER:
+		val->strval = BQ27XXX_MANUFACTURER;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+static void bq27xxx_external_power_changed(struct power_supply *psy)
+{
+	struct bq27xxx_device_info *di = power_supply_get_drvdata(psy);
+
+	cancel_delayed_work_sync(&di->work);
+	schedule_delayed_work(&di->work, 0);
+}
+
+static int bq27xxx_powersupply_init(struct bq27xxx_device_info *di,
+				    const char *name)
+{
+	int ret;
+	struct power_supply_desc *psy_desc;
+	struct power_supply_config psy_cfg = { .drv_data = di, };
+
+	psy_desc = devm_kzalloc(di->dev, sizeof(*psy_desc), GFP_KERNEL);
+	if (!psy_desc)
+		return -ENOMEM;
+
+	psy_desc->name = name;
+	psy_desc->type = POWER_SUPPLY_TYPE_BATTERY;
+	psy_desc->properties = bq27xxx_battery_props[di->chip].props;
+	psy_desc->num_properties = bq27xxx_battery_props[di->chip].size;
+	psy_desc->get_property = bq27xxx_battery_get_property;
+	psy_desc->external_power_changed = bq27xxx_external_power_changed;
+
+	INIT_DELAYED_WORK(&di->work, bq27xxx_battery_poll);
+	mutex_init(&di->lock);
+
+	di->bat = power_supply_register_no_ws(di->dev, psy_desc, &psy_cfg);
+	if (IS_ERR(di->bat)) {
+		ret = PTR_ERR(di->bat);
+		dev_err(di->dev, "failed to register battery: %d\n", ret);
+		return ret;
+	}
+
+	dev_info(di->dev, "support ver. %s enabled\n", DRIVER_VERSION);
+
+	bq27xxx_battery_update(di);
+
+	return 0;
+}
+
+static void bq27xxx_powersupply_unregister(struct bq27xxx_device_info *di)
+{
+	/*
+	 * power_supply_unregister call bq27xxx_battery_get_property which
+	 * call bq27xxx_battery_poll.
+	 * Make sure that bq27xxx_battery_poll will not call
+	 * schedule_delayed_work again after unregister (which cause OOPS).
+	 */
+	poll_interval = 0;
+
+	cancel_delayed_work_sync(&di->work);
+
+	power_supply_unregister(di->bat);
+
+	mutex_destroy(&di->lock);
+}
+
+/* i2c specific code */
+#ifdef CONFIG_BATTERY_BQ27XXX_I2C
+
+/* If the system has several batteries we need a different name for each
+ * of them...
+ */
+static DEFINE_IDR(battery_id);
+static DEFINE_MUTEX(battery_mutex);
+
+static irqreturn_t bq27xxx_battery_irq_handler_thread(int irq, void *data)
+{
+	struct bq27xxx_device_info *di = data;
+
+	bq27xxx_battery_update(di);
+
+	return IRQ_HANDLED;
+}
+
+static int bq27xxx_battery_i2c_read(struct bq27xxx_device_info *di, u8 reg,
+				    bool single)
+{
+	struct i2c_client *client = to_i2c_client(di->dev);
+	struct i2c_msg msg[2];
+	unsigned char data[2];
+	int ret;
+
+	if (!client->adapter)
+		return -ENODEV;
+
+	msg[0].addr = client->addr;
+	msg[0].flags = 0;
+	msg[0].buf = &reg;
+	msg[0].len = sizeof(reg);
+	msg[1].addr = client->addr;
+	msg[1].flags = I2C_M_RD;
+	msg[1].buf = data;
+	if (single)
+		msg[1].len = 1;
+	else
+		msg[1].len = 2;
+
+	ret = i2c_transfer(client->adapter, msg, ARRAY_SIZE(msg));
+	if (ret < 0)
+		return ret;
+
+	if (!single)
+		ret = get_unaligned_le16(data);
+	else
+		ret = data[0];
+
+	return ret;
+}
+
+static int bq27xxx_battery_i2c_probe(struct i2c_client *client,
+				     const struct i2c_device_id *id)
+{
+	char *name;
+	struct bq27xxx_device_info *di;
+	int num;
+	int retval = 0;
+
+	/* Get new ID for the new battery device */
+	mutex_lock(&battery_mutex);
+	num = idr_alloc(&battery_id, client, 0, 0, GFP_KERNEL);
+	mutex_unlock(&battery_mutex);
+	if (num < 0)
+		return num;
+
+	name = devm_kasprintf(&client->dev, GFP_KERNEL, "%s-%d", id->name, num);
+	if (!name) {
+		retval = -ENOMEM;
+		goto batt_failed;
+	}
+
+	di = devm_kzalloc(&client->dev, sizeof(*di), GFP_KERNEL);
+	if (!di) {
+		retval = -ENOMEM;
+		goto batt_failed;
+	}
+
+	di->id = num;
+	di->dev = &client->dev;
+	di->chip = id->driver_data;
+	di->bus.read = &bq27xxx_battery_i2c_read;
+	di->regs = bq27xxx_regs[di->chip];
+
+	retval = bq27xxx_powersupply_init(di, name);
+	if (retval)
+		goto batt_failed;
+
+	/* Schedule a polling after about 1 min */
+	schedule_delayed_work(&di->work, 60 * HZ);
+
+	i2c_set_clientdata(client, di);
+
+	if (client->irq) {
+		retval = devm_request_threaded_irq(&client->dev, client->irq,
+				NULL, bq27xxx_battery_irq_handler_thread,
+				IRQF_ONESHOT,
+				name, di);
+		if (retval) {
+			dev_err(&client->dev,
+				"Unable to register IRQ %d error %d\n",
+				client->irq, retval);
+			return retval;
+		}
+	}
+
+	return 0;
+
+batt_failed:
+	mutex_lock(&battery_mutex);
+	idr_remove(&battery_id, num);
+	mutex_unlock(&battery_mutex);
+
+	return retval;
+}
+
+static int bq27xxx_battery_i2c_remove(struct i2c_client *client)
+{
+	struct bq27xxx_device_info *di = i2c_get_clientdata(client);
+
+	bq27xxx_powersupply_unregister(di);
+
+	mutex_lock(&battery_mutex);
+	idr_remove(&battery_id, di->id);
+	mutex_unlock(&battery_mutex);
+
+	return 0;
+}
+
+static const struct i2c_device_id bq27xxx_id[] = {
+	{ "bq27200", BQ27000 },
+	{ "bq27210", BQ27010 },
+	{ "bq27500", BQ27500 },
+	{ "bq27510", BQ27500 },
+	{ "bq27520", BQ27500 },
+	{ "bq27530", BQ27530 },
+	{ "bq27531", BQ27530 },
+	{ "bq27541", BQ27541 },
+	{ "bq27542", BQ27541 },
+	{ "bq27546", BQ27541 },
+	{ "bq27742", BQ27541 },
+	{ "bq27545", BQ27545 },
+	{ "bq27421", BQ27421 },
+	{ "bq27425", BQ27421 },
+	{ "bq27441", BQ27421 },
+	{ "bq27621", BQ27421 },
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, bq27xxx_id);
+
+static struct i2c_driver bq27xxx_battery_i2c_driver = {
+	.driver = {
+		.name = "bq27xxx-battery",
+	},
+	.probe = bq27xxx_battery_i2c_probe,
+	.remove = bq27xxx_battery_i2c_remove,
+	.id_table = bq27xxx_id,
+};
+
+static inline int bq27xxx_battery_i2c_init(void)
+{
+	int ret = i2c_add_driver(&bq27xxx_battery_i2c_driver);
+
+	if (ret)
+		pr_err("Unable to register BQ27xxx i2c driver\n");
+
+	return ret;
+}
+
+static inline void bq27xxx_battery_i2c_exit(void)
+{
+	i2c_del_driver(&bq27xxx_battery_i2c_driver);
+}
+
+#else
+
+static inline int bq27xxx_battery_i2c_init(void) { return 0; }
+static inline void bq27xxx_battery_i2c_exit(void) {};
+
+#endif
+
+/* platform specific code */
+#ifdef CONFIG_BATTERY_BQ27XXX_PLATFORM
+
+static int bq27xxx_battery_platform_read(struct bq27xxx_device_info *di, u8 reg,
+					 bool single)
+{
+	struct device *dev = di->dev;
+	struct bq27xxx_platform_data *pdata = dev->platform_data;
+	unsigned int timeout = 3;
+	int upper, lower;
+	int temp;
+
+	if (!single) {
+		/* Make sure the value has not changed in between reading the
+		 * lower and the upper part */
+		upper = pdata->read(dev, reg + 1);
+		do {
+			temp = upper;
+			if (upper < 0)
+				return upper;
+
+			lower = pdata->read(dev, reg);
+			if (lower < 0)
+				return lower;
+
+			upper = pdata->read(dev, reg + 1);
+		} while (temp != upper && --timeout);
+
+		if (timeout == 0)
+			return -EIO;
+
+		return (upper << 8) | lower;
+	}
+
+	return pdata->read(dev, reg);
+}
+
+static int bq27xxx_battery_platform_probe(struct platform_device *pdev)
+{
+	struct bq27xxx_device_info *di;
+	struct bq27xxx_platform_data *pdata = pdev->dev.platform_data;
+	const char *name;
+
+	if (!pdata) {
+		dev_err(&pdev->dev, "no platform_data supplied\n");
+		return -EINVAL;
+	}
+
+	if (!pdata->read) {
+		dev_err(&pdev->dev, "no hdq read callback supplied\n");
+		return -EINVAL;
+	}
+
+	if (!pdata->chip) {
+		dev_err(&pdev->dev, "no device supplied\n");
+		return -EINVAL;
+	}
+
+	di = devm_kzalloc(&pdev->dev, sizeof(*di), GFP_KERNEL);
+	if (!di)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, di);
+
+	di->dev = &pdev->dev;
+	di->chip = pdata->chip;
+	di->regs = bq27xxx_regs[di->chip];
+
+	name = pdata->name ?: dev_name(&pdev->dev);
+	di->bus.read = &bq27xxx_battery_platform_read;
+
+	return bq27xxx_powersupply_init(di, name);
+}
+
+static int bq27xxx_battery_platform_remove(struct platform_device *pdev)
+{
+	struct bq27xxx_device_info *di = platform_get_drvdata(pdev);
+
+	bq27xxx_powersupply_unregister(di);
+
+	return 0;
+}
+
+static struct platform_driver bq27xxx_battery_platform_driver = {
+	.probe	= bq27xxx_battery_platform_probe,
+	.remove = bq27xxx_battery_platform_remove,
+	.driver = {
+		.name = "bq27000-battery",
+	},
+};
+
+static inline int bq27xxx_battery_platform_init(void)
+{
+	int ret = platform_driver_register(&bq27xxx_battery_platform_driver);
+
+	if (ret)
+		pr_err("Unable to register BQ27xxx platform driver\n");
+
+	return ret;
+}
+
+static inline void bq27xxx_battery_platform_exit(void)
+{
+	platform_driver_unregister(&bq27xxx_battery_platform_driver);
+}
+
+#else
+
+static inline int bq27xxx_battery_platform_init(void) { return 0; }
+static inline void bq27xxx_battery_platform_exit(void) {};
+
+#endif
+
+/*
+ * Module stuff
+ */
+
+static int __init bq27xxx_battery_init(void)
+{
+	int ret;
+
+	ret = bq27xxx_battery_i2c_init();
+	if (ret)
+		return ret;
+
+	ret = bq27xxx_battery_platform_init();
+	if (ret)
+		bq27xxx_battery_i2c_exit();
+
+	return ret;
+}
+module_init(bq27xxx_battery_init);
+
+static void __exit bq27xxx_battery_exit(void)
+{
+	bq27xxx_battery_platform_exit();
+	bq27xxx_battery_i2c_exit();
+}
+module_exit(bq27xxx_battery_exit);
+
+#ifdef CONFIG_BATTERY_BQ27XXX_PLATFORM
+MODULE_ALIAS("platform:bq27000-battery");
+#endif
+
+MODULE_AUTHOR("Rodolfo Giometti <giometti@linux.it>");
+MODULE_DESCRIPTION("BQ27xxx battery monitor driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/power/charger-manager.c b/drivers/power/charger-manager.c
index 907293e..1ea5d1a 100644
--- a/drivers/power/charger-manager.c
+++ b/drivers/power/charger-manager.c
@@ -1581,8 +1581,10 @@
 				cables = devm_kzalloc(dev, sizeof(*cables)
 						* chg_regs->num_cables,
 						GFP_KERNEL);
-				if (!cables)
+				if (!cables) {
+					of_node_put(child);
 					return ERR_PTR(-ENOMEM);
+				}
 
 				chg_regs->cables = cables;
 
diff --git a/drivers/power/lp8727_charger.c b/drivers/power/lp8727_charger.c
index 7e741f1..042fb3da 100644
--- a/drivers/power/lp8727_charger.c
+++ b/drivers/power/lp8727_charger.c
@@ -508,23 +508,23 @@
 	return param;
 }
 
-static int lp8727_parse_dt(struct device *dev)
+static struct lp8727_platform_data *lp8727_parse_dt(struct device *dev)
 {
 	struct device_node *np = dev->of_node;
 	struct device_node *child;
 	struct lp8727_platform_data *pdata;
 	const char *type;
 
-	/* If charging parameter is not defined, just skip parsing the dt */
-	if (of_get_child_count(np) == 0)
-		goto out;
-
 	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
 	if (!pdata)
-		return -ENOMEM;
+		return ERR_PTR(-ENOMEM);
 
 	of_property_read_u32(np, "debounce-ms", &pdata->debounce_msec);
 
+	/* If charging parameter is not defined, just skip parsing the dt */
+	if (of_get_child_count(np) == 0)
+		return pdata;
+
 	for_each_child_of_node(np, child) {
 		of_property_read_string(child, "charger-type", &type);
 
@@ -535,29 +535,30 @@
 			pdata->usb = lp8727_parse_charge_pdata(dev, child);
 	}
 
-	dev->platform_data = pdata;
-out:
-	return 0;
+	return pdata;
 }
 #else
-static int lp8727_parse_dt(struct device *dev)
+static struct lp8727_platform_data *lp8727_parse_dt(struct device *dev)
 {
-	return 0;
+	return NULL;
 }
 #endif
 
 static int lp8727_probe(struct i2c_client *cl, const struct i2c_device_id *id)
 {
 	struct lp8727_chg *pchg;
+	struct lp8727_platform_data *pdata;
 	int ret;
 
 	if (!i2c_check_functionality(cl->adapter, I2C_FUNC_SMBUS_I2C_BLOCK))
 		return -EIO;
 
 	if (cl->dev.of_node) {
-		ret = lp8727_parse_dt(&cl->dev);
-		if (ret)
-			return ret;
+		pdata = lp8727_parse_dt(&cl->dev);
+		if (IS_ERR(pdata))
+			return PTR_ERR(pdata);
+	} else {
+		pdata = dev_get_platdata(&cl->dev);
 	}
 
 	pchg = devm_kzalloc(&cl->dev, sizeof(*pchg), GFP_KERNEL);
@@ -566,7 +567,7 @@
 
 	pchg->client = cl;
 	pchg->dev = &cl->dev;
-	pchg->pdata = cl->dev.platform_data;
+	pchg->pdata = pdata;
 	i2c_set_clientdata(cl, pchg);
 
 	mutex_init(&pchg->xfer_lock);
diff --git a/drivers/power/max17042_battery.c b/drivers/power/max17042_battery.c
index e892557..9c65f13 100644
--- a/drivers/power/max17042_battery.c
+++ b/drivers/power/max17042_battery.c
@@ -909,18 +909,21 @@
 		regmap_write(chip->regmap, MAX17042_LearnCFG, 0x0007);
 	}
 
-	chip->battery = power_supply_register(&client->dev, max17042_desc,
-						&psy_cfg);
+	chip->battery = devm_power_supply_register(&client->dev, max17042_desc,
+						   &psy_cfg);
 	if (IS_ERR(chip->battery)) {
 		dev_err(&client->dev, "failed: power supply register\n");
 		return PTR_ERR(chip->battery);
 	}
 
 	if (client->irq) {
-		ret = request_threaded_irq(client->irq, NULL,
-					max17042_thread_handler,
-					IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
-					chip->battery->desc->name, chip);
+		ret = devm_request_threaded_irq(&client->dev, client->irq,
+						NULL,
+						max17042_thread_handler,
+						IRQF_TRIGGER_FALLING |
+						IRQF_ONESHOT,
+						chip->battery->desc->name,
+						chip);
 		if (!ret) {
 			regmap_update_bits(chip->regmap, MAX17042_CONFIG,
 					CONFIG_ALRT_BIT_ENBL,
@@ -944,16 +947,6 @@
 	return 0;
 }
 
-static int max17042_remove(struct i2c_client *client)
-{
-	struct max17042_chip *chip = i2c_get_clientdata(client);
-
-	if (client->irq)
-		free_irq(client->irq, chip);
-	power_supply_unregister(chip->battery);
-	return 0;
-}
-
 #ifdef CONFIG_PM_SLEEP
 static int max17042_suspend(struct device *dev)
 {
@@ -1014,7 +1007,6 @@
 		.pm	= &max17042_pm_ops,
 	},
 	.probe		= max17042_probe,
-	.remove		= max17042_remove,
 	.id_table	= max17042_id,
 };
 module_i2c_driver(max17042_i2c_driver);
diff --git a/drivers/power/max8903_charger.c b/drivers/power/max8903_charger.c
index bf2b4b3..6d39d52 100644
--- a/drivers/power/max8903_charger.c
+++ b/drivers/power/max8903_charger.c
@@ -201,8 +201,7 @@
 
 	if (pdata->dc_valid == false && pdata->usb_valid == false) {
 		dev_err(dev, "No valid power sources.\n");
-		ret = -EINVAL;
-		goto err;
+		return -EINVAL;
 	}
 
 	if (pdata->dc_valid) {
@@ -216,8 +215,7 @@
 		} else {
 			dev_err(dev, "When DC is wired, DOK and DCM should"
 					" be wired as well.\n");
-			ret = -EINVAL;
-			goto err;
+			return -EINVAL;
 		}
 	} else {
 		if (pdata->dcm) {
@@ -225,8 +223,7 @@
 				gpio_set_value(pdata->dcm, 0);
 			else {
 				dev_err(dev, "Invalid pin: dcm.\n");
-				ret = -EINVAL;
-				goto err;
+				return -EINVAL;
 			}
 		}
 	}
@@ -238,8 +235,7 @@
 		} else {
 			dev_err(dev, "When USB is wired, UOK should be wired."
 					"as well.\n");
-			ret = -EINVAL;
-			goto err;
+			return -EINVAL;
 		}
 	}
 
@@ -248,32 +244,28 @@
 			gpio_set_value(pdata->cen, (ta_in || usb_in) ? 0 : 1);
 		} else {
 			dev_err(dev, "Invalid pin: cen.\n");
-			ret = -EINVAL;
-			goto err;
+			return -EINVAL;
 		}
 	}
 
 	if (pdata->chg) {
 		if (!gpio_is_valid(pdata->chg)) {
 			dev_err(dev, "Invalid pin: chg.\n");
-			ret = -EINVAL;
-			goto err;
+			return -EINVAL;
 		}
 	}
 
 	if (pdata->flt) {
 		if (!gpio_is_valid(pdata->flt)) {
 			dev_err(dev, "Invalid pin: flt.\n");
-			ret = -EINVAL;
-			goto err;
+			return -EINVAL;
 		}
 	}
 
 	if (pdata->usus) {
 		if (!gpio_is_valid(pdata->usus)) {
 			dev_err(dev, "Invalid pin: usus.\n");
-			ret = -EINVAL;
-			goto err;
+			return -EINVAL;
 		}
 	}
 
@@ -291,85 +283,56 @@
 
 	psy_cfg.drv_data = data;
 
-	data->psy = power_supply_register(dev, &data->psy_desc, &psy_cfg);
+	data->psy = devm_power_supply_register(dev, &data->psy_desc, &psy_cfg);
 	if (IS_ERR(data->psy)) {
 		dev_err(dev, "failed: power supply register.\n");
-		ret = PTR_ERR(data->psy);
-		goto err;
+		return PTR_ERR(data->psy);
 	}
 
 	if (pdata->dc_valid) {
-		ret = request_threaded_irq(gpio_to_irq(pdata->dok),
-				NULL, max8903_dcin,
-				IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
-				"MAX8903 DC IN", data);
+		ret = devm_request_threaded_irq(dev, gpio_to_irq(pdata->dok),
+						NULL, max8903_dcin,
+						IRQF_TRIGGER_FALLING |
+						IRQF_TRIGGER_RISING,
+						"MAX8903 DC IN", data);
 		if (ret) {
 			dev_err(dev, "Cannot request irq %d for DC (%d)\n",
 					gpio_to_irq(pdata->dok), ret);
-			goto err_psy;
+			return ret;
 		}
 	}
 
 	if (pdata->usb_valid) {
-		ret = request_threaded_irq(gpio_to_irq(pdata->uok),
-				NULL, max8903_usbin,
-				IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
-				"MAX8903 USB IN", data);
+		ret = devm_request_threaded_irq(dev, gpio_to_irq(pdata->uok),
+						NULL, max8903_usbin,
+						IRQF_TRIGGER_FALLING |
+						IRQF_TRIGGER_RISING,
+						"MAX8903 USB IN", data);
 		if (ret) {
 			dev_err(dev, "Cannot request irq %d for USB (%d)\n",
 					gpio_to_irq(pdata->uok), ret);
-			goto err_dc_irq;
+			return ret;
 		}
 	}
 
 	if (pdata->flt) {
-		ret = request_threaded_irq(gpio_to_irq(pdata->flt),
-				NULL, max8903_fault,
-				IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
-				"MAX8903 Fault", data);
+		ret = devm_request_threaded_irq(dev, gpio_to_irq(pdata->flt),
+						NULL, max8903_fault,
+						IRQF_TRIGGER_FALLING |
+						IRQF_TRIGGER_RISING,
+						"MAX8903 Fault", data);
 		if (ret) {
 			dev_err(dev, "Cannot request irq %d for Fault (%d)\n",
 					gpio_to_irq(pdata->flt), ret);
-			goto err_usb_irq;
+			return ret;
 		}
 	}
 
 	return 0;
-
-err_usb_irq:
-	if (pdata->usb_valid)
-		free_irq(gpio_to_irq(pdata->uok), data);
-err_dc_irq:
-	if (pdata->dc_valid)
-		free_irq(gpio_to_irq(pdata->dok), data);
-err_psy:
-	power_supply_unregister(data->psy);
-err:
-	return ret;
-}
-
-static int max8903_remove(struct platform_device *pdev)
-{
-	struct max8903_data *data = platform_get_drvdata(pdev);
-
-	if (data) {
-		struct max8903_pdata *pdata = &data->pdata;
-
-		if (pdata->flt)
-			free_irq(gpio_to_irq(pdata->flt), data);
-		if (pdata->usb_valid)
-			free_irq(gpio_to_irq(pdata->uok), data);
-		if (pdata->dc_valid)
-			free_irq(gpio_to_irq(pdata->dok), data);
-		power_supply_unregister(data->psy);
-	}
-
-	return 0;
 }
 
 static struct platform_driver max8903_driver = {
 	.probe	= max8903_probe,
-	.remove	= max8903_remove,
 	.driver = {
 		.name	= "max8903-charger",
 	},
diff --git a/drivers/power/max8998_charger.c b/drivers/power/max8998_charger.c
index 47448d4..b64cf0f 100644
--- a/drivers/power/max8998_charger.c
+++ b/drivers/power/max8998_charger.c
@@ -117,8 +117,7 @@
 			"EOC value not set: leave it unchanged.\n");
 	} else {
 		dev_err(max8998->dev, "Invalid EOC value\n");
-		ret = -EINVAL;
-		goto err;
+		return -EINVAL;
 	}
 
 	/* Setup Charge Restart Level */
@@ -141,8 +140,7 @@
 		break;
 	default:
 		dev_err(max8998->dev, "Invalid Restart Level\n");
-		ret = -EINVAL;
-		goto err;
+		return -EINVAL;
 	}
 
 	/* Setup Charge Full Timeout */
@@ -165,34 +163,22 @@
 		break;
 	default:
 		dev_err(max8998->dev, "Invalid Full Timeout value\n");
-		ret = -EINVAL;
-		goto err;
+		return -EINVAL;
 	}
 
 	psy_cfg.drv_data = max8998;
 
-	max8998->battery = power_supply_register(max8998->dev,
-						 &max8998_battery_desc,
-						 &psy_cfg);
+	max8998->battery = devm_power_supply_register(max8998->dev,
+						      &max8998_battery_desc,
+						      &psy_cfg);
 	if (IS_ERR(max8998->battery)) {
 		ret = PTR_ERR(max8998->battery);
 		dev_err(max8998->dev, "failed: power supply register: %d\n",
 			ret);
-		goto err;
+		return ret;
 	}
 
 	return 0;
-err:
-	return ret;
-}
-
-static int max8998_battery_remove(struct platform_device *pdev)
-{
-	struct max8998_battery_data *max8998 = platform_get_drvdata(pdev);
-
-	power_supply_unregister(max8998->battery);
-
-	return 0;
 }
 
 static const struct platform_device_id max8998_battery_id[] = {
@@ -205,7 +191,6 @@
 		.name = "max8998-battery",
 	},
 	.probe = max8998_battery_probe,
-	.remove = max8998_battery_remove,
 	.id_table = max8998_battery_id,
 };
 
diff --git a/drivers/power/pm2301_charger.c b/drivers/power/pm2301_charger.c
index 3a45cc0..8f9bd1d 100644
--- a/drivers/power/pm2301_charger.c
+++ b/drivers/power/pm2301_charger.c
@@ -1264,5 +1264,4 @@
 
 MODULE_LICENSE("GPL v2");
 MODULE_AUTHOR("Rajkumar kasirajan, Olivier Launay");
-MODULE_ALIAS("i2c:pm2xxx-charger");
 MODULE_DESCRIPTION("PM2xxx charger management driver");
diff --git a/drivers/power/qcom_smbb.c b/drivers/power/qcom_smbb.c
new file mode 100644
index 0000000..5eb1e9e
--- /dev/null
+++ b/drivers/power/qcom_smbb.c
@@ -0,0 +1,951 @@
+/* Copyright (c) 2014, Sony Mobile Communications Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * This driver is for the multi-block Switch-Mode Battery Charger and Boost
+ * (SMBB) hardware, found in Qualcomm PM8941 PMICs.  The charger is an
+ * integrated, single-cell lithium-ion battery charger.
+ *
+ * Sub-components:
+ *  - Charger core
+ *  - Buck
+ *  - DC charge-path
+ *  - USB charge-path
+ *  - Battery interface
+ *  - Boost (not implemented)
+ *  - Misc
+ *  - HF-Buck
+ */
+
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define SMBB_CHG_VMAX		0x040
+#define SMBB_CHG_VSAFE		0x041
+#define SMBB_CHG_CFG		0x043
+#define SMBB_CHG_IMAX		0x044
+#define SMBB_CHG_ISAFE		0x045
+#define SMBB_CHG_VIN_MIN	0x047
+#define SMBB_CHG_CTRL		0x049
+#define CTRL_EN			BIT(7)
+#define SMBB_CHG_VBAT_WEAK	0x052
+#define SMBB_CHG_IBAT_TERM_CHG	0x05b
+#define IBAT_TERM_CHG_IEOC	BIT(7)
+#define IBAT_TERM_CHG_IEOC_BMS	BIT(7)
+#define IBAT_TERM_CHG_IEOC_CHG	0
+#define SMBB_CHG_VBAT_DET	0x05d
+#define SMBB_CHG_TCHG_MAX_EN	0x060
+#define TCHG_MAX_EN		BIT(7)
+#define SMBB_CHG_WDOG_TIME	0x062
+#define SMBB_CHG_WDOG_EN	0x065
+#define WDOG_EN			BIT(7)
+
+#define SMBB_BUCK_REG_MODE	0x174
+#define BUCK_REG_MODE		BIT(0)
+#define BUCK_REG_MODE_VBAT	BIT(0)
+#define BUCK_REG_MODE_VSYS	0
+
+#define SMBB_BAT_PRES_STATUS	0x208
+#define PRES_STATUS_BAT_PRES	BIT(7)
+#define SMBB_BAT_TEMP_STATUS	0x209
+#define TEMP_STATUS_OK		BIT(7)
+#define TEMP_STATUS_HOT		BIT(6)
+#define SMBB_BAT_BTC_CTRL	0x249
+#define BTC_CTRL_COMP_EN	BIT(7)
+#define BTC_CTRL_COLD_EXT	BIT(1)
+#define BTC_CTRL_HOT_EXT_N	BIT(0)
+
+#define SMBB_USB_IMAX		0x344
+#define SMBB_USB_ENUM_TIMER_STOP 0x34e
+#define ENUM_TIMER_STOP		BIT(0)
+#define SMBB_USB_SEC_ACCESS	0x3d0
+#define SEC_ACCESS_MAGIC	0xa5
+#define SMBB_USB_REV_BST	0x3ed
+#define REV_BST_CHG_GONE	BIT(7)
+
+#define SMBB_DC_IMAX		0x444
+
+#define SMBB_MISC_REV2		0x601
+#define SMBB_MISC_BOOT_DONE	0x642
+#define BOOT_DONE		BIT(7)
+
+#define STATUS_USBIN_VALID	BIT(0) /* USB connection is valid */
+#define STATUS_DCIN_VALID	BIT(1) /* DC connection is valid */
+#define STATUS_BAT_HOT		BIT(2) /* Battery temp 1=Hot, 0=Cold */
+#define STATUS_BAT_OK		BIT(3) /* Battery temp OK */
+#define STATUS_BAT_PRESENT	BIT(4) /* Battery is present */
+#define STATUS_CHG_DONE		BIT(5) /* Charge cycle is complete */
+#define STATUS_CHG_TRKL		BIT(6) /* Trickle charging */
+#define STATUS_CHG_FAST		BIT(7) /* Fast charging */
+#define STATUS_CHG_GONE		BIT(8) /* No charger is connected */
+
+enum smbb_attr {
+	ATTR_BAT_ISAFE,
+	ATTR_BAT_IMAX,
+	ATTR_USBIN_IMAX,
+	ATTR_DCIN_IMAX,
+	ATTR_BAT_VSAFE,
+	ATTR_BAT_VMAX,
+	ATTR_BAT_VMIN,
+	ATTR_CHG_VDET,
+	ATTR_VIN_MIN,
+	_ATTR_CNT,
+};
+
+struct smbb_charger {
+	unsigned int revision;
+	unsigned int addr;
+	struct device *dev;
+
+	bool dc_disabled;
+	bool jeita_ext_temp;
+	unsigned long status;
+	struct mutex statlock;
+
+	unsigned int attr[_ATTR_CNT];
+
+	struct power_supply *usb_psy;
+	struct power_supply *dc_psy;
+	struct power_supply *bat_psy;
+	struct regmap *regmap;
+};
+
+static int smbb_vbat_weak_fn(unsigned int index)
+{
+	return 2100000 + index * 100000;
+}
+
+static int smbb_vin_fn(unsigned int index)
+{
+	if (index > 42)
+		return 5600000 + (index - 43) * 200000;
+	return 3400000 + index * 50000;
+}
+
+static int smbb_vmax_fn(unsigned int index)
+{
+	return 3240000 + index * 10000;
+}
+
+static int smbb_vbat_det_fn(unsigned int index)
+{
+	return 3240000 + index * 20000;
+}
+
+static int smbb_imax_fn(unsigned int index)
+{
+	if (index < 2)
+		return 100000 + index * 50000;
+	return index * 100000;
+}
+
+static int smbb_bat_imax_fn(unsigned int index)
+{
+	return index * 50000;
+}
+
+static unsigned int smbb_hw_lookup(unsigned int val, int (*fn)(unsigned int))
+{
+	unsigned int widx;
+	unsigned int sel;
+
+	for (widx = sel = 0; (*fn)(widx) <= val; ++widx)
+		sel = widx;
+
+	return sel;
+}
+
+static const struct smbb_charger_attr {
+	const char *name;
+	unsigned int reg;
+	unsigned int safe_reg;
+	unsigned int max;
+	unsigned int min;
+	unsigned int fail_ok;
+	int (*hw_fn)(unsigned int);
+} smbb_charger_attrs[] = {
+	[ATTR_BAT_ISAFE] = {
+		.name = "qcom,fast-charge-safe-current",
+		.reg = SMBB_CHG_ISAFE,
+		.max = 3000000,
+		.min = 200000,
+		.hw_fn = smbb_bat_imax_fn,
+		.fail_ok = 1,
+	},
+	[ATTR_BAT_IMAX] = {
+		.name = "qcom,fast-charge-current-limit",
+		.reg = SMBB_CHG_IMAX,
+		.safe_reg = SMBB_CHG_ISAFE,
+		.max = 3000000,
+		.min = 200000,
+		.hw_fn = smbb_bat_imax_fn,
+	},
+	[ATTR_DCIN_IMAX] = {
+		.name = "qcom,dc-current-limit",
+		.reg = SMBB_DC_IMAX,
+		.max = 2500000,
+		.min = 100000,
+		.hw_fn = smbb_imax_fn,
+	},
+	[ATTR_BAT_VSAFE] = {
+		.name = "qcom,fast-charge-safe-voltage",
+		.reg = SMBB_CHG_VSAFE,
+		.max = 5000000,
+		.min = 3240000,
+		.hw_fn = smbb_vmax_fn,
+		.fail_ok = 1,
+	},
+	[ATTR_BAT_VMAX] = {
+		.name = "qcom,fast-charge-high-threshold-voltage",
+		.reg = SMBB_CHG_VMAX,
+		.safe_reg = SMBB_CHG_VSAFE,
+		.max = 5000000,
+		.min = 3240000,
+		.hw_fn = smbb_vmax_fn,
+	},
+	[ATTR_BAT_VMIN] = {
+		.name = "qcom,fast-charge-low-threshold-voltage",
+		.reg = SMBB_CHG_VBAT_WEAK,
+		.max = 3600000,
+		.min = 2100000,
+		.hw_fn = smbb_vbat_weak_fn,
+	},
+	[ATTR_CHG_VDET] = {
+		.name = "qcom,auto-recharge-threshold-voltage",
+		.reg = SMBB_CHG_VBAT_DET,
+		.max = 5000000,
+		.min = 3240000,
+		.hw_fn = smbb_vbat_det_fn,
+	},
+	[ATTR_VIN_MIN] = {
+		.name = "qcom,minimum-input-voltage",
+		.reg = SMBB_CHG_VIN_MIN,
+		.max = 9600000,
+		.min = 4200000,
+		.hw_fn = smbb_vin_fn,
+	},
+	[ATTR_USBIN_IMAX] = {
+		.name = "usb-charge-current-limit",
+		.reg = SMBB_USB_IMAX,
+		.max = 2500000,
+		.min = 100000,
+		.hw_fn = smbb_imax_fn,
+	},
+};
+
+static int smbb_charger_attr_write(struct smbb_charger *chg,
+		enum smbb_attr which, unsigned int val)
+{
+	const struct smbb_charger_attr *prop;
+	unsigned int wval;
+	unsigned int out;
+	int rc;
+
+	prop = &smbb_charger_attrs[which];
+
+	if (val > prop->max || val < prop->min) {
+		dev_err(chg->dev, "value out of range for %s [%u:%u]\n",
+			prop->name, prop->min, prop->max);
+		return -EINVAL;
+	}
+
+	if (prop->safe_reg) {
+		rc = regmap_read(chg->regmap,
+				chg->addr + prop->safe_reg, &wval);
+		if (rc) {
+			dev_err(chg->dev,
+				"unable to read safe value for '%s'\n",
+				prop->name);
+			return rc;
+		}
+
+		wval = prop->hw_fn(wval);
+
+		if (val > wval) {
+			dev_warn(chg->dev,
+				"%s above safe value, clamping at %u\n",
+				prop->name, wval);
+			val = wval;
+		}
+	}
+
+	wval = smbb_hw_lookup(val, prop->hw_fn);
+
+	rc = regmap_write(chg->regmap, chg->addr + prop->reg, wval);
+	if (rc) {
+		dev_err(chg->dev, "unable to update %s", prop->name);
+		return rc;
+	}
+	out = prop->hw_fn(wval);
+	if (out != val) {
+		dev_warn(chg->dev,
+			"%s inaccurate, rounded to %u\n",
+			prop->name, out);
+	}
+
+	dev_dbg(chg->dev, "%s <= %d\n", prop->name, out);
+
+	chg->attr[which] = out;
+
+	return 0;
+}
+
+static int smbb_charger_attr_read(struct smbb_charger *chg,
+		enum smbb_attr which)
+{
+	const struct smbb_charger_attr *prop;
+	unsigned int val;
+	int rc;
+
+	prop = &smbb_charger_attrs[which];
+
+	rc = regmap_read(chg->regmap, chg->addr + prop->reg, &val);
+	if (rc) {
+		dev_err(chg->dev, "failed to read %s\n", prop->name);
+		return rc;
+	}
+	val = prop->hw_fn(val);
+	dev_dbg(chg->dev, "%s => %d\n", prop->name, val);
+
+	chg->attr[which] = val;
+
+	return 0;
+}
+
+static int smbb_charger_attr_parse(struct smbb_charger *chg,
+		enum smbb_attr which)
+{
+	const struct smbb_charger_attr *prop;
+	unsigned int val;
+	int rc;
+
+	prop = &smbb_charger_attrs[which];
+
+	rc = of_property_read_u32(chg->dev->of_node, prop->name, &val);
+	if (rc == 0) {
+		rc = smbb_charger_attr_write(chg, which, val);
+		if (!rc || !prop->fail_ok)
+			return rc;
+	}
+	return smbb_charger_attr_read(chg, which);
+}
+
+static void smbb_set_line_flag(struct smbb_charger *chg, int irq, int flag)
+{
+	bool state;
+	int ret;
+
+	ret = irq_get_irqchip_state(irq, IRQCHIP_STATE_LINE_LEVEL, &state);
+	if (ret < 0) {
+		dev_err(chg->dev, "failed to read irq line\n");
+		return;
+	}
+
+	mutex_lock(&chg->statlock);
+	if (state)
+		chg->status |= flag;
+	else
+		chg->status &= ~flag;
+	mutex_unlock(&chg->statlock);
+
+	dev_dbg(chg->dev, "status = %03lx\n", chg->status);
+}
+
+static irqreturn_t smbb_usb_valid_handler(int irq, void *_data)
+{
+	struct smbb_charger *chg = _data;
+
+	smbb_set_line_flag(chg, irq, STATUS_USBIN_VALID);
+	power_supply_changed(chg->usb_psy);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t smbb_dc_valid_handler(int irq, void *_data)
+{
+	struct smbb_charger *chg = _data;
+
+	smbb_set_line_flag(chg, irq, STATUS_DCIN_VALID);
+	if (!chg->dc_disabled)
+		power_supply_changed(chg->dc_psy);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t smbb_bat_temp_handler(int irq, void *_data)
+{
+	struct smbb_charger *chg = _data;
+	unsigned int val;
+	int rc;
+
+	rc = regmap_read(chg->regmap, chg->addr + SMBB_BAT_TEMP_STATUS, &val);
+	if (rc)
+		return IRQ_HANDLED;
+
+	mutex_lock(&chg->statlock);
+	if (val & TEMP_STATUS_OK) {
+		chg->status |= STATUS_BAT_OK;
+	} else {
+		chg->status &= ~STATUS_BAT_OK;
+		if (val & TEMP_STATUS_HOT)
+			chg->status |= STATUS_BAT_HOT;
+	}
+	mutex_unlock(&chg->statlock);
+
+	power_supply_changed(chg->bat_psy);
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t smbb_bat_present_handler(int irq, void *_data)
+{
+	struct smbb_charger *chg = _data;
+
+	smbb_set_line_flag(chg, irq, STATUS_BAT_PRESENT);
+	power_supply_changed(chg->bat_psy);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t smbb_chg_done_handler(int irq, void *_data)
+{
+	struct smbb_charger *chg = _data;
+
+	smbb_set_line_flag(chg, irq, STATUS_CHG_DONE);
+	power_supply_changed(chg->bat_psy);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t smbb_chg_gone_handler(int irq, void *_data)
+{
+	struct smbb_charger *chg = _data;
+
+	smbb_set_line_flag(chg, irq, STATUS_CHG_GONE);
+	power_supply_changed(chg->bat_psy);
+	power_supply_changed(chg->usb_psy);
+	if (!chg->dc_disabled)
+		power_supply_changed(chg->dc_psy);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t smbb_chg_fast_handler(int irq, void *_data)
+{
+	struct smbb_charger *chg = _data;
+
+	smbb_set_line_flag(chg, irq, STATUS_CHG_FAST);
+	power_supply_changed(chg->bat_psy);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t smbb_chg_trkl_handler(int irq, void *_data)
+{
+	struct smbb_charger *chg = _data;
+
+	smbb_set_line_flag(chg, irq, STATUS_CHG_TRKL);
+	power_supply_changed(chg->bat_psy);
+
+	return IRQ_HANDLED;
+}
+
+static const struct smbb_irq {
+	const char *name;
+	irqreturn_t (*handler)(int, void *);
+} smbb_charger_irqs[] = {
+	{ "chg-done", smbb_chg_done_handler },
+	{ "chg-fast", smbb_chg_fast_handler },
+	{ "chg-trkl", smbb_chg_trkl_handler },
+	{ "bat-temp-ok", smbb_bat_temp_handler },
+	{ "bat-present", smbb_bat_present_handler },
+	{ "chg-gone", smbb_chg_gone_handler },
+	{ "usb-valid", smbb_usb_valid_handler },
+	{ "dc-valid", smbb_dc_valid_handler },
+};
+
+static int smbb_usbin_get_property(struct power_supply *psy,
+		enum power_supply_property psp,
+		union power_supply_propval *val)
+{
+	struct smbb_charger *chg = power_supply_get_drvdata(psy);
+	int rc = 0;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_ONLINE:
+		mutex_lock(&chg->statlock);
+		val->intval = !(chg->status & STATUS_CHG_GONE) &&
+				(chg->status & STATUS_USBIN_VALID);
+		mutex_unlock(&chg->statlock);
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT:
+		val->intval = chg->attr[ATTR_USBIN_IMAX];
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT_MAX:
+		val->intval = 2500000;
+		break;
+	default:
+		rc = -EINVAL;
+		break;
+	}
+
+	return rc;
+}
+
+static int smbb_usbin_set_property(struct power_supply *psy,
+		enum power_supply_property psp,
+		const union power_supply_propval *val)
+{
+	struct smbb_charger *chg = power_supply_get_drvdata(psy);
+	int rc;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT:
+		rc = smbb_charger_attr_write(chg, ATTR_USBIN_IMAX,
+				val->intval);
+		break;
+	default:
+		rc = -EINVAL;
+		break;
+	}
+
+	return rc;
+}
+
+static int smbb_dcin_get_property(struct power_supply *psy,
+		enum power_supply_property psp,
+		union power_supply_propval *val)
+{
+	struct smbb_charger *chg = power_supply_get_drvdata(psy);
+	int rc = 0;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_ONLINE:
+		mutex_lock(&chg->statlock);
+		val->intval = !(chg->status & STATUS_CHG_GONE) &&
+				(chg->status & STATUS_DCIN_VALID);
+		mutex_unlock(&chg->statlock);
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT:
+		val->intval = chg->attr[ATTR_DCIN_IMAX];
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT_MAX:
+		val->intval = 2500000;
+		break;
+	default:
+		rc = -EINVAL;
+		break;
+	}
+
+	return rc;
+}
+
+static int smbb_dcin_set_property(struct power_supply *psy,
+		enum power_supply_property psp,
+		const union power_supply_propval *val)
+{
+	struct smbb_charger *chg = power_supply_get_drvdata(psy);
+	int rc;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT:
+		rc = smbb_charger_attr_write(chg, ATTR_DCIN_IMAX,
+				val->intval);
+		break;
+	default:
+		rc = -EINVAL;
+		break;
+	}
+
+	return rc;
+}
+
+static int smbb_charger_writable_property(struct power_supply *psy,
+		enum power_supply_property psp)
+{
+	return psp == POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT;
+}
+
+static int smbb_battery_get_property(struct power_supply *psy,
+		enum power_supply_property psp,
+		union power_supply_propval *val)
+{
+	struct smbb_charger *chg = power_supply_get_drvdata(psy);
+	unsigned long status;
+	int rc = 0;
+
+	mutex_lock(&chg->statlock);
+	status = chg->status;
+	mutex_unlock(&chg->statlock);
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_STATUS:
+		if (status & STATUS_CHG_GONE)
+			val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+		else if (!(status & (STATUS_DCIN_VALID | STATUS_USBIN_VALID)))
+			val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+		else if (status & STATUS_CHG_DONE)
+			val->intval = POWER_SUPPLY_STATUS_FULL;
+		else if (!(status & STATUS_BAT_OK))
+			val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+		else if (status & (STATUS_CHG_FAST | STATUS_CHG_TRKL))
+			val->intval = POWER_SUPPLY_STATUS_CHARGING;
+		else /* everything is ok for charging, but we are not... */
+			val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+		break;
+	case POWER_SUPPLY_PROP_HEALTH:
+		if (status & STATUS_BAT_OK)
+			val->intval = POWER_SUPPLY_HEALTH_GOOD;
+		else if (status & STATUS_BAT_HOT)
+			val->intval = POWER_SUPPLY_HEALTH_OVERHEAT;
+		else
+			val->intval = POWER_SUPPLY_HEALTH_COLD;
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_TYPE:
+		if (status & STATUS_CHG_FAST)
+			val->intval = POWER_SUPPLY_CHARGE_TYPE_FAST;
+		else if (status & STATUS_CHG_TRKL)
+			val->intval = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
+		else
+			val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE;
+		break;
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = !!(status & STATUS_BAT_PRESENT);
+		break;
+	case POWER_SUPPLY_PROP_CURRENT_MAX:
+		val->intval = chg->attr[ATTR_BAT_IMAX];
+		break;
+	case POWER_SUPPLY_PROP_VOLTAGE_MAX:
+		val->intval = chg->attr[ATTR_BAT_VMAX];
+		break;
+	case POWER_SUPPLY_PROP_TECHNOLOGY:
+		/* this charger is a single-cell lithium-ion battery charger
+		* only.  If you hook up some other technology, there will be
+		* fireworks.
+		*/
+		val->intval = POWER_SUPPLY_TECHNOLOGY_LION;
+		break;
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
+		val->intval = 3000000; /* single-cell li-ion low end */
+		break;
+	default:
+		rc = -EINVAL;
+		break;
+	}
+
+	return rc;
+}
+
+static int smbb_battery_set_property(struct power_supply *psy,
+		enum power_supply_property psp,
+		const union power_supply_propval *val)
+{
+	struct smbb_charger *chg = power_supply_get_drvdata(psy);
+	int rc;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_CURRENT_MAX:
+		rc = smbb_charger_attr_write(chg, ATTR_BAT_IMAX, val->intval);
+		break;
+	case POWER_SUPPLY_PROP_VOLTAGE_MAX:
+		rc = smbb_charger_attr_write(chg, ATTR_BAT_VMAX, val->intval);
+		break;
+	default:
+		rc = -EINVAL;
+		break;
+	}
+
+	return rc;
+}
+
+static int smbb_battery_writable_property(struct power_supply *psy,
+		enum power_supply_property psp)
+{
+	switch (psp) {
+	case POWER_SUPPLY_PROP_CURRENT_MAX:
+	case POWER_SUPPLY_PROP_VOLTAGE_MAX:
+		return 1;
+	default:
+		return 0;
+	}
+}
+
+static enum power_supply_property smbb_charger_properties[] = {
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT,
+	POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT_MAX,
+};
+
+static enum power_supply_property smbb_battery_properties[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_CHARGE_TYPE,
+	POWER_SUPPLY_PROP_CURRENT_MAX,
+	POWER_SUPPLY_PROP_VOLTAGE_MAX,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+};
+
+static const struct reg_off_mask_default {
+	unsigned int offset;
+	unsigned int mask;
+	unsigned int value;
+	unsigned int rev_mask;
+} smbb_charger_setup[] = {
+	/* The bootloader is supposed to set this... make sure anyway. */
+	{ SMBB_MISC_BOOT_DONE, BOOT_DONE, BOOT_DONE },
+
+	/* Disable software timer */
+	{ SMBB_CHG_TCHG_MAX_EN, TCHG_MAX_EN, 0 },
+
+	/* Clear and disable watchdog */
+	{ SMBB_CHG_WDOG_TIME, 0xff, 160 },
+	{ SMBB_CHG_WDOG_EN, WDOG_EN, 0 },
+
+	/* Use charger based EoC detection */
+	{ SMBB_CHG_IBAT_TERM_CHG, IBAT_TERM_CHG_IEOC, IBAT_TERM_CHG_IEOC_CHG },
+
+	/* Disable GSM PA load adjustment.
+	* The PA signal is incorrectly connected on v2.
+	*/
+	{ SMBB_CHG_CFG, 0xff, 0x00, BIT(3) },
+
+	/* Use VBAT (not VSYS) to compensate for IR drop during fast charging */
+	{ SMBB_BUCK_REG_MODE, BUCK_REG_MODE, BUCK_REG_MODE_VBAT },
+
+	/* Enable battery temperature comparators */
+	{ SMBB_BAT_BTC_CTRL, BTC_CTRL_COMP_EN, BTC_CTRL_COMP_EN },
+
+	/* Stop USB enumeration timer */
+	{ SMBB_USB_ENUM_TIMER_STOP, ENUM_TIMER_STOP, ENUM_TIMER_STOP },
+
+#if 0 /* FIXME supposedly only to disable hardware ARB termination */
+	{ SMBB_USB_SEC_ACCESS, SEC_ACCESS_MAGIC },
+	{ SMBB_USB_REV_BST, 0xff, REV_BST_CHG_GONE },
+#endif
+
+	/* Stop USB enumeration timer, again */
+	{ SMBB_USB_ENUM_TIMER_STOP, ENUM_TIMER_STOP, ENUM_TIMER_STOP },
+
+	/* Enable charging */
+	{ SMBB_CHG_CTRL, CTRL_EN, CTRL_EN },
+};
+
+static char *smbb_bif[] = { "smbb-bif" };
+
+static const struct power_supply_desc bat_psy_desc = {
+	.name = "smbb-bif",
+	.type = POWER_SUPPLY_TYPE_BATTERY,
+	.properties = smbb_battery_properties,
+	.num_properties = ARRAY_SIZE(smbb_battery_properties),
+	.get_property = smbb_battery_get_property,
+	.set_property = smbb_battery_set_property,
+	.property_is_writeable = smbb_battery_writable_property,
+};
+
+static const struct power_supply_desc usb_psy_desc = {
+	.name = "smbb-usbin",
+	.type = POWER_SUPPLY_TYPE_USB,
+	.properties = smbb_charger_properties,
+	.num_properties = ARRAY_SIZE(smbb_charger_properties),
+	.get_property = smbb_usbin_get_property,
+	.set_property = smbb_usbin_set_property,
+	.property_is_writeable = smbb_charger_writable_property,
+};
+
+static const struct power_supply_desc dc_psy_desc = {
+	.name = "smbb-dcin",
+	.type = POWER_SUPPLY_TYPE_MAINS,
+	.properties = smbb_charger_properties,
+	.num_properties = ARRAY_SIZE(smbb_charger_properties),
+	.get_property = smbb_dcin_get_property,
+	.set_property = smbb_dcin_set_property,
+	.property_is_writeable = smbb_charger_writable_property,
+};
+
+static int smbb_charger_probe(struct platform_device *pdev)
+{
+	struct power_supply_config bat_cfg = {};
+	struct power_supply_config usb_cfg = {};
+	struct power_supply_config dc_cfg = {};
+	struct smbb_charger *chg;
+	int rc, i;
+
+	chg = devm_kzalloc(&pdev->dev, sizeof(*chg), GFP_KERNEL);
+	if (!chg)
+		return -ENOMEM;
+
+	chg->dev = &pdev->dev;
+	mutex_init(&chg->statlock);
+
+	chg->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!chg->regmap) {
+		dev_err(&pdev->dev, "failed to locate regmap\n");
+		return -ENODEV;
+	}
+
+	rc = of_property_read_u32(pdev->dev.of_node, "reg", &chg->addr);
+	if (rc) {
+		dev_err(&pdev->dev, "missing or invalid 'reg' property\n");
+		return rc;
+	}
+
+	rc = regmap_read(chg->regmap, chg->addr + SMBB_MISC_REV2, &chg->revision);
+	if (rc) {
+		dev_err(&pdev->dev, "unable to read revision\n");
+		return rc;
+	}
+
+	chg->revision += 1;
+	if (chg->revision != 2 && chg->revision != 3) {
+		dev_err(&pdev->dev, "v1 hardware not supported\n");
+		return -ENODEV;
+	}
+	dev_info(&pdev->dev, "Initializing SMBB rev %u", chg->revision);
+
+	chg->dc_disabled = of_property_read_bool(pdev->dev.of_node, "qcom,disable-dc");
+
+	for (i = 0; i < _ATTR_CNT; ++i) {
+		rc = smbb_charger_attr_parse(chg, i);
+		if (rc) {
+			dev_err(&pdev->dev, "failed to parse/apply settings\n");
+			return rc;
+		}
+	}
+
+	bat_cfg.drv_data = chg;
+	bat_cfg.of_node = pdev->dev.of_node;
+	chg->bat_psy = devm_power_supply_register(&pdev->dev,
+						  &bat_psy_desc,
+						  &bat_cfg);
+	if (IS_ERR(chg->bat_psy)) {
+		dev_err(&pdev->dev, "failed to register battery\n");
+		return PTR_ERR(chg->bat_psy);
+	}
+
+	usb_cfg.drv_data = chg;
+	usb_cfg.supplied_to = smbb_bif;
+	usb_cfg.num_supplicants = ARRAY_SIZE(smbb_bif);
+	chg->usb_psy = devm_power_supply_register(&pdev->dev,
+						  &usb_psy_desc,
+						  &usb_cfg);
+	if (IS_ERR(chg->usb_psy)) {
+		dev_err(&pdev->dev, "failed to register USB power supply\n");
+		return PTR_ERR(chg->usb_psy);
+	}
+
+	if (!chg->dc_disabled) {
+		dc_cfg.drv_data = chg;
+		dc_cfg.supplied_to = smbb_bif;
+		dc_cfg.num_supplicants = ARRAY_SIZE(smbb_bif);
+		chg->dc_psy = devm_power_supply_register(&pdev->dev,
+							 &dc_psy_desc,
+							 &dc_cfg);
+		if (IS_ERR(chg->dc_psy)) {
+			dev_err(&pdev->dev, "failed to register DC power supply\n");
+			return PTR_ERR(chg->dc_psy);
+		}
+	}
+
+	for (i = 0; i < ARRAY_SIZE(smbb_charger_irqs); ++i) {
+		int irq;
+
+		irq = platform_get_irq_byname(pdev, smbb_charger_irqs[i].name);
+		if (irq < 0) {
+			dev_err(&pdev->dev, "failed to get irq '%s'\n",
+				smbb_charger_irqs[i].name);
+			return irq;
+		}
+
+		smbb_charger_irqs[i].handler(irq, chg);
+
+		rc = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+				smbb_charger_irqs[i].handler, IRQF_ONESHOT,
+				smbb_charger_irqs[i].name, chg);
+		if (rc) {
+			dev_err(&pdev->dev, "failed to request irq '%s'\n",
+				smbb_charger_irqs[i].name);
+			return rc;
+		}
+	}
+
+	chg->jeita_ext_temp = of_property_read_bool(pdev->dev.of_node,
+			"qcom,jeita-extended-temp-range");
+
+	/* Set temperature range to [35%:70%] or [25%:80%] accordingly */
+	rc = regmap_update_bits(chg->regmap, chg->addr + SMBB_BAT_BTC_CTRL,
+			BTC_CTRL_COLD_EXT | BTC_CTRL_HOT_EXT_N,
+			chg->jeita_ext_temp ?
+				BTC_CTRL_COLD_EXT :
+				BTC_CTRL_HOT_EXT_N);
+	if (rc) {
+		dev_err(&pdev->dev,
+			"unable to set %s temperature range\n",
+			chg->jeita_ext_temp ? "JEITA extended" : "normal");
+		return rc;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(smbb_charger_setup); ++i) {
+		const struct reg_off_mask_default *r = &smbb_charger_setup[i];
+
+		if (r->rev_mask & BIT(chg->revision))
+			continue;
+
+		rc = regmap_update_bits(chg->regmap, chg->addr + r->offset,
+				r->mask, r->value);
+		if (rc) {
+			dev_err(&pdev->dev,
+				"unable to initializing charging, bailing\n");
+			return rc;
+		}
+	}
+
+	platform_set_drvdata(pdev, chg);
+
+	return 0;
+}
+
+static int smbb_charger_remove(struct platform_device *pdev)
+{
+	struct smbb_charger *chg;
+
+	chg = platform_get_drvdata(pdev);
+
+	regmap_update_bits(chg->regmap, chg->addr + SMBB_CHG_CTRL, CTRL_EN, 0);
+
+	return 0;
+}
+
+static const struct of_device_id smbb_charger_id_table[] = {
+	{ .compatible = "qcom,pm8941-charger" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, smbb_charger_id_table);
+
+static struct platform_driver smbb_charger_driver = {
+	.probe	  = smbb_charger_probe,
+	.remove	 = smbb_charger_remove,
+	.driver	 = {
+		.name   = "qcom-smbb",
+		.of_match_table = smbb_charger_id_table,
+	},
+};
+module_platform_driver(smbb_charger_driver);
+
+MODULE_DESCRIPTION("Qualcomm Switch-Mode Battery Charger and Boost driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig
index 5a0189b..1131cf7 100644
--- a/drivers/power/reset/Kconfig
+++ b/drivers/power/reset/Kconfig
@@ -15,7 +15,7 @@
 	  This driver supports turning off board via a ams AS3722 power-off.
 
 config POWER_RESET_AT91_POWEROFF
-	bool "Atmel AT91 poweroff driver"
+	tristate "Atmel AT91 poweroff driver"
 	depends on ARCH_AT91
 	default SOC_AT91SAM9 || SOC_SAMA5
 	help
@@ -23,7 +23,7 @@
 	  SoCs
 
 config POWER_RESET_AT91_RESET
-	bool "Atmel AT91 reset driver"
+	tristate "Atmel AT91 reset driver"
 	depends on ARCH_AT91
 	default SOC_AT91SAM9 || SOC_SAMA5
 	help
diff --git a/drivers/power/reset/at91-poweroff.c b/drivers/power/reset/at91-poweroff.c
index 9847cfb..e9e24df 100644
--- a/drivers/power/reset/at91-poweroff.c
+++ b/drivers/power/reset/at91-poweroff.c
@@ -10,6 +10,7 @@
  * warranty of any kind, whether express or implied.
  */
 
+#include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/module.h>
 #include <linux/of.h>
@@ -48,6 +49,7 @@
 };
 
 static void __iomem *at91_shdwc_base;
+static struct clk *sclk;
 
 static void __init at91_wakeup_status(void)
 {
@@ -119,9 +121,10 @@
 	writel(wakeup_mode | mode, at91_shdwc_base + AT91_SHDW_MR);
 }
 
-static int at91_poweroff_probe(struct platform_device *pdev)
+static int __init at91_poweroff_probe(struct platform_device *pdev)
 {
 	struct resource *res;
+	int ret;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	at91_shdwc_base = devm_ioremap_resource(&pdev->dev, res);
@@ -130,6 +133,16 @@
 		return PTR_ERR(at91_shdwc_base);
 	}
 
+	sclk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(sclk))
+		return PTR_ERR(sclk);
+
+	ret = clk_prepare_enable(sclk);
+	if (ret) {
+		dev_err(&pdev->dev, "Could not enable slow clock\n");
+		return ret;
+	}
+
 	at91_wakeup_status();
 
 	if (pdev->dev.of_node)
@@ -140,6 +153,16 @@
 	return 0;
 }
 
+static int __exit at91_poweroff_remove(struct platform_device *pdev)
+{
+	if (pm_power_off == at91_poweroff)
+		pm_power_off = NULL;
+
+	clk_disable_unprepare(sclk);
+
+	return 0;
+}
+
 static const struct of_device_id at91_poweroff_of_match[] = {
 	{ .compatible = "atmel,at91sam9260-shdwc", },
 	{ .compatible = "atmel,at91sam9rl-shdwc", },
@@ -148,10 +171,14 @@
 };
 
 static struct platform_driver at91_poweroff_driver = {
-	.probe = at91_poweroff_probe,
+	.remove = __exit_p(at91_poweroff_remove),
 	.driver = {
 		.name = "at91-poweroff",
 		.of_match_table = at91_poweroff_of_match,
 	},
 };
-module_platform_driver(at91_poweroff_driver);
+module_platform_driver_probe(at91_poweroff_driver, at91_poweroff_probe);
+
+MODULE_AUTHOR("Atmel Corporation");
+MODULE_DESCRIPTION("Shutdown driver for Atmel SoCs");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/power/reset/at91-reset.c b/drivers/power/reset/at91-reset.c
index c378d4e..3f6b5dd 100644
--- a/drivers/power/reset/at91-reset.c
+++ b/drivers/power/reset/at91-reset.c
@@ -1,5 +1,5 @@
 /*
- * Atmel AT91 SAM9 SoCs reset code
+ * Atmel AT91 SAM9 & SAMA5 SoCs reset code
  *
  * Copyright (C) 2007 Atmel Corporation.
  * Copyright (C) BitBox Ltd 2010
@@ -11,6 +11,7 @@
  * warranty of any kind, whether express or implied.
  */
 
+#include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/module.h>
 #include <linux/of_address.h>
@@ -46,6 +47,7 @@
 };
 
 static void __iomem *at91_ramc_base[2], *at91_rstc_base;
+static struct clk *sclk;
 
 /*
 * unless the SDRAM is cleanly shutdown before we hit the
@@ -178,11 +180,11 @@
 	.priority = 192,
 };
 
-static int at91_reset_of_probe(struct platform_device *pdev)
+static int __init at91_reset_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *match;
 	struct device_node *np;
-	int idx = 0;
+	int ret, idx = 0;
 
 	at91_rstc_base = of_iomap(pdev->dev.of_node, 0);
 	if (!at91_rstc_base) {
@@ -204,57 +206,36 @@
 
 	match = of_match_node(at91_reset_of_match, pdev->dev.of_node);
 	at91_restart_nb.notifier_call = match->data;
-	return register_restart_handler(&at91_restart_nb);
-}
 
-static int at91_reset_platform_probe(struct platform_device *pdev)
-{
-	const struct platform_device_id *match;
-	struct resource *res;
-	int idx = 0;
+	sclk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(sclk))
+		return PTR_ERR(sclk);
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	at91_rstc_base = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(at91_rstc_base)) {
-		dev_err(&pdev->dev, "Could not map reset controller address\n");
-		return PTR_ERR(at91_rstc_base);
-	}
-
-	for (idx = 0; idx < 2; idx++) {
-		res = platform_get_resource(pdev, IORESOURCE_MEM, idx + 1 );
-		at91_ramc_base[idx] = devm_ioremap(&pdev->dev, res->start,
-						   resource_size(res));
-		if (!at91_ramc_base[idx]) {
-			dev_err(&pdev->dev, "Could not map ram controller address\n");
-			return -ENOMEM;
-		}
-	}
-
-	match = platform_get_device_id(pdev);
-	at91_restart_nb.notifier_call =
-		(int (*)(struct notifier_block *,
-			 unsigned long, void *)) match->driver_data;
-
-	return register_restart_handler(&at91_restart_nb);
-}
-
-static int at91_reset_probe(struct platform_device *pdev)
-{
-	int ret;
-
-	if (pdev->dev.of_node)
-		ret = at91_reset_of_probe(pdev);
-	else
-		ret = at91_reset_platform_probe(pdev);
-
-	if (ret)
+	ret = clk_prepare_enable(sclk);
+	if (ret) {
+		dev_err(&pdev->dev, "Could not enable slow clock\n");
 		return ret;
+	}
+
+	ret = register_restart_handler(&at91_restart_nb);
+	if (ret) {
+		clk_disable_unprepare(sclk);
+		return ret;
+	}
 
 	at91_reset_status(pdev);
 
 	return 0;
 }
 
+static int __exit at91_reset_remove(struct platform_device *pdev)
+{
+	unregister_restart_handler(&at91_restart_nb);
+	clk_disable_unprepare(sclk);
+
+	return 0;
+}
+
 static const struct platform_device_id at91_reset_plat_match[] = {
 	{ "at91-sam9260-reset", (unsigned long)at91sam9260_restart },
 	{ "at91-sam9g45-reset", (unsigned long)at91sam9g45_restart },
@@ -262,11 +243,15 @@
 };
 
 static struct platform_driver at91_reset_driver = {
-	.probe = at91_reset_probe,
+	.remove = __exit_p(at91_reset_remove),
 	.driver = {
 		.name = "at91-reset",
 		.of_match_table = at91_reset_of_match,
 	},
 	.id_table = at91_reset_plat_match,
 };
-module_platform_driver(at91_reset_driver);
+module_platform_driver_probe(at91_reset_driver, at91_reset_probe);
+
+MODULE_AUTHOR("Atmel Corporation");
+MODULE_DESCRIPTION("Reset driver for Atmel SoCs");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/power/rt9455_charger.c b/drivers/power/rt9455_charger.c
index a49a9d4..cfdbde9 100644
--- a/drivers/power/rt9455_charger.c
+++ b/drivers/power/rt9455_charger.c
@@ -1760,5 +1760,4 @@
 
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Anda-Maria Nicolae <anda-maria.nicolae@intel.com>");
-MODULE_ALIAS("i2c:rt9455-charger");
 MODULE_DESCRIPTION("Richtek RT9455 Charger Driver");
diff --git a/drivers/power/smb347-charger.c b/drivers/power/smb347-charger.c
index 0b60a0b..072c518 100644
--- a/drivers/power/smb347-charger.c
+++ b/drivers/power/smb347-charger.c
@@ -1332,4 +1332,3 @@
 MODULE_AUTHOR("Mika Westerberg <mika.westerberg@linux.intel.com>");
 MODULE_DESCRIPTION("SMB347 battery charger driver");
 MODULE_LICENSE("GPL");
-MODULE_ALIAS("i2c:smb347");
diff --git a/drivers/power/tps65090-charger.c b/drivers/power/tps65090-charger.c
index 7e8fbd2..1b4b5e0 100644
--- a/drivers/power/tps65090-charger.c
+++ b/drivers/power/tps65090-charger.c
@@ -353,6 +353,7 @@
 	{ .compatible = "ti,tps65090-charger", },
 	{ /* end */ }
 };
+MODULE_DEVICE_TABLE(of, of_tps65090_charger_match);
 
 static struct platform_driver tps65090_charger_driver = {
 	.driver	= {
diff --git a/drivers/power/tps65217_charger.c b/drivers/power/tps65217_charger.c
new file mode 100644
index 0000000..d9f5673
--- /dev/null
+++ b/drivers/power/tps65217_charger.c
@@ -0,0 +1,264 @@
+/*
+ * Battery charger driver for TI's tps65217
+ *
+ * Copyright (c) 2015, Collabora Ltd.
+
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * Battery charger driver for TI's tps65217
+ */
+#include <linux/kernel.h>
+#include <linux/kthread.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/power_supply.h>
+
+#include <linux/mfd/core.h>
+#include <linux/mfd/tps65217.h>
+
+#define POLL_INTERVAL		(HZ * 2)
+
+struct tps65217_charger {
+	struct tps65217 *tps;
+	struct device *dev;
+	struct power_supply *ac;
+
+	int	ac_online;
+	int	prev_ac_online;
+
+	struct task_struct	*poll_task;
+};
+
+static enum power_supply_property tps65217_ac_props[] = {
+	POWER_SUPPLY_PROP_ONLINE,
+};
+
+static int tps65217_config_charger(struct tps65217_charger *charger)
+{
+	int ret;
+
+	dev_dbg(charger->dev, "%s\n", __func__);
+
+	/*
+	 * tps65217 rev. G, p. 31 (see p. 32 for NTC schematic)
+	 *
+	 * The device can be configured to support a 100k NTC (B = 3960) by
+	 * setting the the NTC_TYPE bit in register CHGCONFIG1 to 1. However it
+	 * is not recommended to do so. In sleep mode, the charger continues
+	 * charging the battery, but all register values are reset to default
+	 * values. Therefore, the charger would get the wrong temperature
+	 * information. If 100k NTC setting is required, please contact the
+	 * factory.
+	 *
+	 * ATTENTION, conflicting information, from p. 46
+	 *
+	 * NTC TYPE (for battery temperature measurement)
+	 *   0 – 100k (curve 1, B = 3960)
+	 *   1 – 10k  (curve 2, B = 3480) (default on reset)
+	 *
+	 */
+	ret = tps65217_clear_bits(charger->tps, TPS65217_REG_CHGCONFIG1,
+				  TPS65217_CHGCONFIG1_NTC_TYPE,
+				  TPS65217_PROTECT_NONE);
+	if (ret) {
+		dev_err(charger->dev,
+			"failed to set 100k NTC setting: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int tps65217_enable_charging(struct tps65217_charger *charger)
+{
+	int ret;
+
+	/* charger already enabled */
+	if (charger->ac_online)
+		return 0;
+
+	dev_dbg(charger->dev, "%s: enable charging\n", __func__);
+	ret = tps65217_set_bits(charger->tps, TPS65217_REG_CHGCONFIG1,
+				TPS65217_CHGCONFIG1_CHG_EN,
+				TPS65217_CHGCONFIG1_CHG_EN,
+				TPS65217_PROTECT_NONE);
+	if (ret) {
+		dev_err(charger->dev,
+			"%s: Error in writing CHG_EN in reg 0x%x: %d\n",
+			__func__, TPS65217_REG_CHGCONFIG1, ret);
+		return ret;
+	}
+
+	charger->ac_online = 1;
+
+	return 0;
+}
+
+static int tps65217_ac_get_property(struct power_supply *psy,
+			enum power_supply_property psp,
+			union power_supply_propval *val)
+{
+	struct tps65217_charger *charger = power_supply_get_drvdata(psy);
+
+	if (psp == POWER_SUPPLY_PROP_ONLINE) {
+		val->intval = charger->ac_online;
+		return 0;
+	}
+	return -EINVAL;
+}
+
+static irqreturn_t tps65217_charger_irq(int irq, void *dev)
+{
+	int ret, val;
+	struct tps65217_charger *charger = dev;
+
+	charger->prev_ac_online = charger->ac_online;
+
+	ret = tps65217_reg_read(charger->tps, TPS65217_REG_STATUS, &val);
+	if (ret < 0) {
+		dev_err(charger->dev, "%s: Error in reading reg 0x%x\n",
+			__func__, TPS65217_REG_STATUS);
+		return IRQ_HANDLED;
+	}
+
+	dev_dbg(charger->dev, "%s: 0x%x\n", __func__, val);
+
+	/* check for AC status bit */
+	if (val & TPS65217_STATUS_ACPWR) {
+		ret = tps65217_enable_charging(charger);
+		if (ret) {
+			dev_err(charger->dev,
+				"failed to enable charger: %d\n", ret);
+			return IRQ_HANDLED;
+		}
+	} else {
+		charger->ac_online = 0;
+	}
+
+	if (charger->prev_ac_online != charger->ac_online)
+		power_supply_changed(charger->ac);
+
+	ret = tps65217_reg_read(charger->tps, TPS65217_REG_CHGCONFIG0, &val);
+	if (ret < 0) {
+		dev_err(charger->dev, "%s: Error in reading reg 0x%x\n",
+			__func__, TPS65217_REG_CHGCONFIG0);
+		return IRQ_HANDLED;
+	}
+
+	if (val & TPS65217_CHGCONFIG0_ACTIVE)
+		dev_dbg(charger->dev, "%s: charger is charging\n", __func__);
+	else
+		dev_dbg(charger->dev,
+			"%s: charger is NOT charging\n", __func__);
+
+	return IRQ_HANDLED;
+}
+
+static int tps65217_charger_poll_task(void *data)
+{
+	set_freezable();
+
+	while (!kthread_should_stop()) {
+		schedule_timeout_interruptible(POLL_INTERVAL);
+		try_to_freeze();
+		tps65217_charger_irq(-1, data);
+	}
+	return 0;
+}
+
+static const struct power_supply_desc tps65217_charger_desc = {
+	.name			= "tps65217-ac",
+	.type			= POWER_SUPPLY_TYPE_MAINS,
+	.get_property		= tps65217_ac_get_property,
+	.properties		= tps65217_ac_props,
+	.num_properties		= ARRAY_SIZE(tps65217_ac_props),
+};
+
+static int tps65217_charger_probe(struct platform_device *pdev)
+{
+	struct tps65217 *tps = dev_get_drvdata(pdev->dev.parent);
+	struct tps65217_charger *charger;
+	int ret;
+
+	dev_dbg(&pdev->dev, "%s\n", __func__);
+
+	charger = devm_kzalloc(&pdev->dev, sizeof(*charger), GFP_KERNEL);
+	if (!charger)
+		return -ENOMEM;
+
+	charger->tps = tps;
+	charger->dev = &pdev->dev;
+
+	charger->ac = devm_power_supply_register(&pdev->dev,
+						 &tps65217_charger_desc,
+						 NULL);
+	if (IS_ERR(charger->ac)) {
+		dev_err(&pdev->dev, "failed: power supply register\n");
+		return PTR_ERR(charger->ac);
+	}
+
+	ret = tps65217_config_charger(charger);
+	if (ret < 0) {
+		dev_err(charger->dev, "charger config failed, err %d\n", ret);
+		return ret;
+	}
+
+	charger->poll_task = kthread_run(tps65217_charger_poll_task,
+				      charger, "ktps65217charger");
+	if (IS_ERR(charger->poll_task)) {
+		ret = PTR_ERR(charger->poll_task);
+		dev_err(charger->dev, "Unable to run kthread err %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int tps65217_charger_remove(struct platform_device *pdev)
+{
+	struct tps65217_charger *charger = platform_get_drvdata(pdev);
+
+	kthread_stop(charger->poll_task);
+
+	return 0;
+}
+
+static const struct of_device_id tps65217_charger_match_table[] = {
+	{ .compatible = "ti,tps65217-charger", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, tps65217_charger_match_table);
+
+static struct platform_driver tps65217_charger_driver = {
+	.probe	= tps65217_charger_probe,
+	.remove = tps65217_charger_remove,
+	.driver	= {
+		.name	= "tps65217-charger",
+		.of_match_table = of_match_ptr(tps65217_charger_match_table),
+	},
+
+};
+module_platform_driver(tps65217_charger_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Enric Balletbo Serra <enric.balletbo@collabora.com>");
+MODULE_DESCRIPTION("TPS65217 battery charger driver");
diff --git a/drivers/power/twl4030_charger.c b/drivers/power/twl4030_charger.c
index 74f2d3f..bcd4dc3 100644
--- a/drivers/power/twl4030_charger.c
+++ b/drivers/power/twl4030_charger.c
@@ -22,7 +22,7 @@
 #include <linux/power_supply.h>
 #include <linux/notifier.h>
 #include <linux/usb/otg.h>
-#include <linux/i2c/twl4030-madc.h>
+#include <linux/iio/consumer.h>
 
 #define TWL4030_BCIMDEN		0x00
 #define TWL4030_BCIMDKEY	0x01
@@ -91,21 +91,23 @@
 #define TWL4030_MSTATEC_COMPLETE1	0x0b
 #define TWL4030_MSTATEC_COMPLETE4	0x0e
 
-#if IS_REACHABLE(CONFIG_TWL4030_MADC)
 /*
  * If AC (Accessory Charger) voltage exceeds 4.5V (MADC 11)
  * then AC is available.
  */
-static inline int ac_available(void)
+static inline int ac_available(struct iio_channel *channel_vac)
 {
-	return twl4030_get_madc_conversion(11) > 4500;
+	int val, err;
+
+	if (!channel_vac)
+		return 0;
+
+	err = iio_read_channel_processed(channel_vac, &val);
+	if (err < 0)
+		return 0;
+	return val > 4500;
 }
-#else
-static inline int ac_available(void)
-{
-	return 0;
-}
-#endif
+
 static bool allow_usb;
 module_param(allow_usb, bool, 0644);
 MODULE_PARM_DESC(allow_usb, "Allow USB charge drawing default current");
@@ -128,6 +130,7 @@
 	 */
 	unsigned int		ichg_eoc, ichg_lo, ichg_hi;
 	unsigned int		usb_cur, ac_cur;
+	struct iio_channel	*channel_vac;
 	bool			ac_is_active;
 	int			usb_mode, ac_mode; /* charging mode requested */
 #define	CHARGE_OFF	0
@@ -278,7 +281,7 @@
 	 * If AC (Accessory Charger) voltage exceeds 4.5V (MADC 11)
 	 * and AC is enabled, set current for 'ac'
 	 */
-	if (ac_available()) {
+	if (ac_available(bci->channel_vac)) {
 		cur = bci->ac_cur;
 		bci->ac_is_active = true;
 	} else {
@@ -1048,6 +1051,12 @@
 		return ret;
 	}
 
+	bci->channel_vac = iio_channel_get(&pdev->dev, "vac");
+	if (IS_ERR(bci->channel_vac)) {
+		bci->channel_vac = NULL;
+		dev_warn(&pdev->dev, "could not request vac iio channel");
+	}
+
 	INIT_WORK(&bci->work, twl4030_bci_usb_work);
 	INIT_DELAYED_WORK(&bci->current_worker, twl4030_current_worker);
 
@@ -1069,7 +1078,7 @@
 			       TWL4030_INTERRUPTS_BCIIMR1A);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "failed to unmask interrupts: %d\n", ret);
-		return ret;
+		goto fail;
 	}
 
 	reg = ~(u32)(TWL4030_VBATOV | TWL4030_VBUSOV | TWL4030_ACCHGOV);
@@ -1102,6 +1111,10 @@
 		twl4030_charger_enable_backup(0, 0);
 
 	return 0;
+fail:
+	iio_channel_release(bci->channel_vac);
+
+	return ret;
 }
 
 static int __exit twl4030_bci_remove(struct platform_device *pdev)
@@ -1112,6 +1125,8 @@
 	twl4030_charger_enable_usb(bci, false);
 	twl4030_charger_enable_backup(0, 0);
 
+	iio_channel_release(bci->channel_vac);
+
 	device_remove_file(&bci->usb->dev, &dev_attr_max_current);
 	device_remove_file(&bci->usb->dev, &dev_attr_mode);
 	device_remove_file(&bci->ac->dev, &dev_attr_max_current);
diff --git a/drivers/power/wm831x_power.c b/drivers/power/wm831x_power.c
index db11ae6..7082301 100644
--- a/drivers/power/wm831x_power.c
+++ b/drivers/power/wm831x_power.c
@@ -499,7 +499,8 @@
 	struct wm831x_power *power;
 	int ret, irq, i;
 
-	power = kzalloc(sizeof(struct wm831x_power), GFP_KERNEL);
+	power = devm_kzalloc(&pdev->dev, sizeof(struct wm831x_power),
+			     GFP_KERNEL);
 	if (power == NULL)
 		return -ENOMEM;
 
@@ -536,7 +537,7 @@
 					    NULL);
 	if (IS_ERR(power->wall)) {
 		ret = PTR_ERR(power->wall);
-		goto err_kmalloc;
+		goto err;
 	}
 
 	power->usb_desc.name = power->usb_name,
@@ -572,7 +573,7 @@
 
 	irq = wm831x_irq(wm831x, platform_get_irq_byname(pdev, "SYSLO"));
 	ret = request_threaded_irq(irq, NULL, wm831x_syslo_irq,
-				   IRQF_TRIGGER_RISING, "System power low",
+				   IRQF_TRIGGER_RISING | IRQF_ONESHOT, "System power low",
 				   power);
 	if (ret != 0) {
 		dev_err(&pdev->dev, "Failed to request SYSLO IRQ %d: %d\n",
@@ -582,7 +583,7 @@
 
 	irq = wm831x_irq(wm831x, platform_get_irq_byname(pdev, "PWR SRC"));
 	ret = request_threaded_irq(irq, NULL, wm831x_pwr_src_irq,
-				   IRQF_TRIGGER_RISING, "Power source",
+				   IRQF_TRIGGER_RISING | IRQF_ONESHOT, "Power source",
 				   power);
 	if (ret != 0) {
 		dev_err(&pdev->dev, "Failed to request PWR SRC IRQ %d: %d\n",
@@ -595,7 +596,7 @@
 				 platform_get_irq_byname(pdev,
 							 wm831x_bat_irqs[i]));
 		ret = request_threaded_irq(irq, NULL, wm831x_bat_irq,
-					   IRQF_TRIGGER_RISING,
+					   IRQF_TRIGGER_RISING | IRQF_ONESHOT,
 					   wm831x_bat_irqs[i],
 					   power);
 		if (ret != 0) {
@@ -626,8 +627,7 @@
 	power_supply_unregister(power->usb);
 err_wall:
 	power_supply_unregister(power->wall);
-err_kmalloc:
-	kfree(power);
+err:
 	return ret;
 }
 
@@ -654,7 +654,6 @@
 		power_supply_unregister(wm831x_power->battery);
 	power_supply_unregister(wm831x_power->wall);
 	power_supply_unregister(wm831x_power->usb);
-	kfree(wm831x_power);
 	return 0;
 }
 
diff --git a/drivers/w1/slaves/w1_bq27000.c b/drivers/w1/slaves/w1_bq27000.c
index caafb17..9f4a86b 100644
--- a/drivers/w1/slaves/w1_bq27000.c
+++ b/drivers/w1/slaves/w1_bq27000.c
@@ -15,7 +15,7 @@
 #include <linux/types.h>
 #include <linux/platform_device.h>
 #include <linux/mutex.h>
-#include <linux/power/bq27x00_battery.h>
+#include <linux/power/bq27xxx_battery.h>
 
 #include "../w1.h"
 #include "../w1_int.h"
@@ -39,9 +39,10 @@
 	return val;
 }
 
-static struct bq27000_platform_data bq27000_battery_info = {
+static struct bq27xxx_platform_data bq27000_battery_info = {
 	.read   = w1_bq27000_read,
 	.name   = "bq27000-battery",
+	.chip   = BQ27000,
 };
 
 static int w1_bq27000_add_slave(struct w1_slave *sl)
diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
index cc8ad1e..b24c771 100644
--- a/include/linux/mfd/axp20x.h
+++ b/include/linux/mfd/axp20x.h
@@ -11,6 +11,8 @@
 #ifndef __LINUX_MFD_AXP20X_H
 #define __LINUX_MFD_AXP20X_H
 
+#include <linux/regmap.h>
+
 enum {
 	AXP152_ID = 0,
 	AXP202_ID,
@@ -438,4 +440,26 @@
 	struct gpio_desc *gpio_mux_cntl;
 };
 
+/* generic helper function for reading 9-16 bit wide regs */
+static inline int axp20x_read_variable_width(struct regmap *regmap,
+	unsigned int reg, unsigned int width)
+{
+	unsigned int reg_val, result;
+	int err;
+
+	err = regmap_read(regmap, reg, &reg_val);
+	if (err)
+		return err;
+
+	result = reg_val << (width - 8);
+
+	err = regmap_read(regmap, reg + 1, &reg_val);
+	if (err)
+		return err;
+
+	result |= reg_val;
+
+	return result;
+}
+
 #endif /* __LINUX_MFD_AXP20X_H */
diff --git a/include/linux/power/bq27x00_battery.h b/include/linux/power/bq27x00_battery.h
deleted file mode 100644
index a857f71..0000000
--- a/include/linux/power/bq27x00_battery.h
+++ /dev/null
@@ -1,19 +0,0 @@
-#ifndef __LINUX_BQ27X00_BATTERY_H__
-#define __LINUX_BQ27X00_BATTERY_H__
-
-/**
- * struct bq27000_plaform_data - Platform data for bq27000 devices
- * @name: Name of the battery. If NULL the driver will fallback to "bq27000".
- * @read: HDQ read callback.
- *	This function should provide access to the HDQ bus the battery is
- *	connected to.
- *	The first parameter is a pointer to the battery device, the second the
- *	register to be read. The return value should either be the content of
- *	the passed register or an error value.
- */
-struct bq27000_platform_data {
-	const char *name;
-	int (*read)(struct device *dev, unsigned int);
-};
-
-#endif
diff --git a/include/linux/power/bq27xxx_battery.h b/include/linux/power/bq27xxx_battery.h
new file mode 100644
index 0000000..45f6a7b
--- /dev/null
+++ b/include/linux/power/bq27xxx_battery.h
@@ -0,0 +1,31 @@
+#ifndef __LINUX_BQ27X00_BATTERY_H__
+#define __LINUX_BQ27X00_BATTERY_H__
+
+/**
+ * struct bq27xxx_plaform_data - Platform data for bq27xxx devices
+ * @name: Name of the battery.
+ * @chip: Chip class number of this device.
+ * @read: HDQ read callback.
+ *	This function should provide access to the HDQ bus the battery is
+ *	connected to.
+ *	The first parameter is a pointer to the battery device, the second the
+ *	register to be read. The return value should either be the content of
+ *	the passed register or an error value.
+ */
+enum bq27xxx_chip {
+	BQ27000 = 1, /* bq27000, bq27200 */
+	BQ27010, /* bq27010, bq27210 */
+	BQ27500, /* bq27500, bq27510, bq27520 */
+	BQ27530, /* bq27530, bq27531 */
+	BQ27541, /* bq27541, bq27542, bq27546, bq27742 */
+	BQ27545, /* bq27545 */
+	BQ27421, /* bq27421, bq27425, bq27441, bq27621 */
+};
+
+struct bq27xxx_platform_data {
+	const char *name;
+	enum bq27xxx_chip chip;
+	int (*read)(struct device *dev, unsigned int);
+};
+
+#endif
diff --git a/include/linux/power/charger-manager.h b/include/linux/power/charger-manager.h
index eadf28c..c4fa907 100644
--- a/include/linux/power/charger-manager.h
+++ b/include/linux/power/charger-manager.h
@@ -65,7 +65,7 @@
 	const char *extcon_name;
 	const char *name;
 
-	/* The charger-manager use Exton framework*/
+	/* The charger-manager use Extcon framework */
 	struct extcon_specific_cable_nb extcon_dev;
 	struct work_struct wq;
 	struct notifier_block nb;
@@ -94,7 +94,7 @@
  *	the charger will be maintained with disabled state.
  * @cables:
  *	the array of charger cables to enable/disable charger
- *	and set current limit according to constratint data of
+ *	and set current limit according to constraint data of
  *	struct charger_cable if only charger cable included
  *	in the array of charger cables is attached/detached.
  * @num_cables: the number of charger cables.
@@ -148,7 +148,7 @@
  * @polling_interval_ms: interval in millisecond at which
  *	charger manager will monitor battery health
  * @battery_present:
- *	Specify where information for existance of battery can be obtained
+ *	Specify where information for existence of battery can be obtained
  * @psy_charger_stat: the names of power-supply for chargers
  * @num_charger_regulator: the number of entries in charger_regulators
  * @charger_regulators: array of charger regulators
@@ -156,7 +156,7 @@
  * @thermal_zone : the name of thermal zone for battery
  * @temp_min : Minimum battery temperature for charging.
  * @temp_max : Maximum battery temperature for charging.
- * @temp_diff : Temperature diffential to restart charging.
+ * @temp_diff : Temperature difference to restart charging.
  * @measure_battery_temp:
  *	true: measure battery temperature
  *	false: measure ambient temperature