Fix some typos in Documentation/: 'A'
This patch fixes typos in various Documentation txts.
This patch addresses some words starting with the letter 'A'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
diff --git a/Documentation/networking/3c509.txt b/Documentation/networking/3c509.txt
index 867a99f..0643e3b 100644
--- a/Documentation/networking/3c509.txt
+++ b/Documentation/networking/3c509.txt
@@ -126,7 +126,7 @@
or impossible in normal operation. Possible causes of this error report are:
- a "green" mode enabled that slows the processor down when there is no
- keyboard activitiy.
+ keyboard activity.
- some other device or device driver hogging the bus or disabling interrupts.
Check /proc/interrupts for excessive interrupt counts. The timer tick
diff --git a/Documentation/networking/cxgb.txt b/Documentation/networking/cxgb.txt
index 7632463..7b23175 100644
--- a/Documentation/networking/cxgb.txt
+++ b/Documentation/networking/cxgb.txt
@@ -56,7 +56,7 @@
ethtool -C eth0 rx-usecs 100
- You may also provide a timer latency value while disabling adpative-rx:
+ You may also provide a timer latency value while disabling adaptive-rx:
ethtool -C <interface> adaptive-rx off rx-usecs <microseconds>
diff --git a/Documentation/networking/dl2k.txt b/Documentation/networking/dl2k.txt
index d4604920..a3a3c6e 100644
--- a/Documentation/networking/dl2k.txt
+++ b/Documentation/networking/dl2k.txt
@@ -173,7 +173,7 @@
Parameter Description
=====================
-You can install this driver without any addtional parameter. However, if you
+You can install this driver without any additional parameter. However, if you
are going to have extensive functions then it is necessary to set extra
parameter. Below is a list of the command line parameters supported by the
Linux device
diff --git a/Documentation/networking/dmfe.txt b/Documentation/networking/dmfe.txt
index 0463635..b1b7499 100644
--- a/Documentation/networking/dmfe.txt
+++ b/Documentation/networking/dmfe.txt
@@ -34,7 +34,7 @@
ifconfig eth0 172.22.3.18
^^^^^^^^^^^
- Your IP Adress
+ Your IP Address
Then you may have to modify the default routing table with command :
diff --git a/Documentation/networking/operstates.txt b/Documentation/networking/operstates.txt
index 4a21d9b..c9074f9 100644
--- a/Documentation/networking/operstates.txt
+++ b/Documentation/networking/operstates.txt
@@ -2,7 +2,7 @@
1. Introduction
Linux distinguishes between administrative and operational state of an
-interface. Admininstrative state is the result of "ip link set dev
+interface. Administrative state is the result of "ip link set dev
<dev> up or down" and reflects whether the administrator wants to use
the device for traffic.
diff --git a/Documentation/networking/packet_mmap.txt b/Documentation/networking/packet_mmap.txt
index aaf99d5..7816262 100644
--- a/Documentation/networking/packet_mmap.txt
+++ b/Documentation/networking/packet_mmap.txt
@@ -296,7 +296,7 @@
- struct tpacket_hdr
- pad to TPACKET_ALIGNMENT=16
- struct sockaddr_ll
- - Gap, chosen so that packet data (Start+tp_net) alignes to
+ - Gap, chosen so that packet data (Start+tp_net) aligns to
TPACKET_ALIGNMENT=16
- Start+tp_mac: [ Optional MAC header ]
- Start+tp_net: Packet data, aligned to TPACKET_ALIGNMENT=16.
diff --git a/Documentation/networking/pktgen.txt b/Documentation/networking/pktgen.txt
index 18d385c..c2f859f 100644
--- a/Documentation/networking/pktgen.txt
+++ b/Documentation/networking/pktgen.txt
@@ -7,7 +7,7 @@
Enable CONFIG_NET_PKTGEN to compile and build pktgen.o either in kernel
or as module. Module is preferred. insmod pktgen if needed. Once running
-pktgen creates a thread on each CPU where each thread has affinty it's CPU.
+pktgen creates a thread on each CPU where each thread has affinity to its CPU.
Monitoring and controlling is done via /proc. Easiest to select a suitable
a sample script and configure.
@@ -32,7 +32,7 @@
Stopped: eth1
Result: OK: max_before_softirq=10000
-Most important the devices assigend to thread. Note! A device can only belong
+Most important the devices assigned to thread. Note! A device can only belong
to one thread.
