diff --git a/Documentation/devicetree/bindings/net/broadcom-mdio-unimac.txt b/Documentation/devicetree/bindings/net/broadcom-mdio-unimac.txt
new file mode 100644
index 0000000..ab0bb42
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/broadcom-mdio-unimac.txt
@@ -0,0 +1,39 @@
+* Broadcom UniMAC MDIO bus controller
+
+Required properties:
+- compatible: should one from "brcm,genet-mdio-v1", "brcm,genet-mdio-v2",
+  "brcm,genet-mdio-v3", "brcm,genet-mdio-v4" or "brcm,unimac-mdio"
+- reg: address and length of the regsiter set for the device, first one is the
+  base register, and the second one is optional and for indirect accesses to
+  larger than 16-bits MDIO transactions
+- reg-names: name(s) of the register must be "mdio" and optional "mdio_indir_rw"
+- #size-cells: must be 1
+- #address-cells: must be 0
+
+Optional properties:
+- interrupts: must be one if the interrupt is shared with the Ethernet MAC or
+  Ethernet switch this MDIO block is integrated from, or must be two, if there
+  are two separate interrupts, first one must be "mdio done" and second must be
+  for "mdio error"
+- interrupt-names: must be "mdio_done_error" when there is a share interrupt fed
+  to this hardware block, or must be "mdio_done" for the first interrupt and
+  "mdio_error" for the second when there are separate interrupts
+
+Child nodes of this MDIO bus controller node are standard Ethernet PHY device
+nodes as described in Documentation/devicetree/bindings/net/phy.txt
+
+Example:
+
+mdio@403c0 {
+	compatible = "brcm,unimac-mdio";
+	reg = <0x403c0 0x8 0x40300 0x18>;
+	reg-names = "mdio", "mdio_indir_rw";
+	#size-cells = <1>;
+	#address-cells = <0>;
+
+	...
+	phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/broadcom-sf2.txt b/Documentation/devicetree/bindings/net/broadcom-sf2.txt
new file mode 100644
index 0000000..30d4875
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/broadcom-sf2.txt
@@ -0,0 +1,78 @@
+* Broadcom Starfighter 2 integrated swich
+
+Required properties:
+
+- compatible: should be "brcm,bcm7445-switch-v4.0"
+- reg: addresses and length of the register sets for the device, must be 6
+  pairs of register addresses and lengths
+- interrupts: interrupts for the devices, must be two interrupts
+- dsa,mii-bus: phandle to the MDIO bus controller, see dsa/dsa.txt
+- dsa,ethernet: phandle to the CPU network interface controller, see dsa/dsa.txt
+- #size-cells: must be 0
+- #address-cells: must be 2, see dsa/dsa.txt
+
+Subnodes:
+
+The integrated switch subnode should be specified according to the binding
+described in dsa/dsa.txt.
+
+Optional properties:
+
+- reg-names: litteral names for the device base register addresses, when present
+  must be: "core", "reg", "intrl2_0", "intrl2_1", "fcb", "acb"
+
+- interrupt-names: litternal names for the device interrupt lines, when present
+  must be: "switch_0" and "switch_1"
+
+- brcm,num-gphy: specify the maximum number of integrated gigabit PHYs in the
+  switch
+
+- brcm,num-rgmii-ports: specify the maximum number of RGMII interfaces supported
+  by the switch
+
+- brcm,fcb-pause-override: boolean property, if present indicates that the switch
+  supports Failover Control Block pause override capability
+
+- brcm,acb-packets-inflight: boolean property, if present indicates that the switch
+  Admission Control Block supports reporting the number of packets in-flight in a
+  switch queue
+
+Example:
+
+switch_top@f0b00000 {
+	compatible = "simple-bus";
+	#size-cells = <1>;
+	#address-cells = <1>;
+	ranges = <0 0xf0b00000 0x40804>;
+
+	ethernet_switch@0 {
+		compatible = "brcm,bcm7445-switch-v4.0";
+		#size-cells = <0>;
+		#address-cells = <2>;
+		reg = <0x0 0x40000
+			0x40000 0x110
+			0x40340 0x30
+			0x40380 0x30
+			0x40400 0x34
+			0x40600 0x208>;
+		interrupts = <0 0x18 0
+				0 0x19 0>;
+		brcm,num-gphy = <1>;
+		brcm,num-rgmii-ports = <2>;
+		brcm,fcb-pause-override;
+		brcm,acb-packets-inflight;
+
+		...
+		switch@0 {
+			reg = <0 0>;
+			#size-cells = <0>;
+			#address-cells <1>;
+
+			port@0 {
+				label = "gphy";
+				reg = <0>;
+			};
+			...
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt
index 49f4f7a..a62c889 100644
--- a/Documentation/devicetree/bindings/net/dsa/dsa.txt
+++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt
@@ -39,6 +39,22 @@
 			  This property is only used when switches are being
 			  chained/cascaded together.
 
+- phy-handle		: Phandle to a PHY on an external MDIO bus, not the
+			  switch internal one. See
+			  Documentation/devicetree/bindings/net/ethernet.txt
+			  for details.
+
+- phy-mode		: String representing the connection to the designated
+			  PHY node specified by the 'phy-handle' property. See
+			  Documentation/devicetree/bindings/net/ethernet.txt
+			  for details.
+
+Optional subnodes:
+- fixed-link		: Fixed-link subnode describing a link to a non-MDIO
+			  managed entity. See
+			  Documentation/devicetree/bindings/net/fixed-link.txt
+			  for details.
+
 Example:
 
 	dsa@0 {
@@ -58,6 +74,7 @@
 			port@0 {
 				reg = <0>;
 				label = "lan1";
+				phy-handle = <&phy0>;
 			};
 
 			port@1 {
diff --git a/drivers/net/dsa/Kconfig b/drivers/net/dsa/Kconfig
index b8fe808..c6ee07c 100644
--- a/drivers/net/dsa/Kconfig
+++ b/drivers/net/dsa/Kconfig
@@ -36,4 +36,15 @@
 	  This enables support for the Marvell 88E6123/6161/6165
 	  ethernet switch chips.
 
+config NET_DSA_BCM_SF2
+	tristate "Broadcom Starfighter 2 Ethernet switch support"
+	select NET_DSA
+	select NET_DSA_TAG_BRCM
+	select FIXED_PHY if NET_DSA_BCM_SF2=y
+	select BCM7XXX_PHY
+	select MDIO_BCM_UNIMAC
+	---help---
+	  This enables support for the Broadcom Starfighter 2 Ethernet
+	  switch chips.
+
 endmenu
diff --git a/drivers/net/dsa/Makefile b/drivers/net/dsa/Makefile
index f3bda05..dd3cd3b 100644
--- a/drivers/net/dsa/Makefile
+++ b/drivers/net/dsa/Makefile
@@ -7,3 +7,4 @@
 ifdef CONFIG_NET_DSA_MV88E6131
 mv88e6xxx_drv-y += mv88e6131.o
 endif
+obj-$(CONFIG_NET_DSA_BCM_SF2)	+= bcm_sf2.o
diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
new file mode 100644
index 0000000..bb7cb8e
--- /dev/null
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -0,0 +1,626 @@
+/*
+ * Broadcom Starfighter 2 DSA switch driver
+ *
+ * Copyright (C) 2014, Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/phy.h>
+#include <linux/phy_fixed.h>
+#include <linux/mii.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <net/dsa.h>
+
+#include "bcm_sf2.h"
+#include "bcm_sf2_regs.h"
+
+/* String, offset, and register size in bytes if different from 4 bytes */
+static const struct bcm_sf2_hw_stats bcm_sf2_mib[] = {
+	{ "TxOctets",		0x000, 8	},
+	{ "TxDropPkts",		0x020		},
+	{ "TxQPKTQ0",		0x030		},
+	{ "TxBroadcastPkts",	0x040		},
+	{ "TxMulticastPkts",	0x050		},
+	{ "TxUnicastPKts",	0x060		},
+	{ "TxCollisions",	0x070		},
+	{ "TxSingleCollision",	0x080		},
+	{ "TxMultipleCollision", 0x090		},
+	{ "TxDeferredCollision", 0x0a0		},
+	{ "TxLateCollision",	0x0b0		},
+	{ "TxExcessiveCollision", 0x0c0		},
+	{ "TxFrameInDisc",	0x0d0		},
+	{ "TxPausePkts",	0x0e0		},
+	{ "TxQPKTQ1",		0x0f0		},
+	{ "TxQPKTQ2",		0x100		},
+	{ "TxQPKTQ3",		0x110		},
+	{ "TxQPKTQ4",		0x120		},
+	{ "TxQPKTQ5",		0x130		},
+	{ "RxOctets",		0x140, 8	},
+	{ "RxUndersizePkts",	0x160		},
+	{ "RxPausePkts",	0x170		},
+	{ "RxPkts64Octets",	0x180		},
+	{ "RxPkts65to127Octets", 0x190		},
+	{ "RxPkts128to255Octets", 0x1a0		},
+	{ "RxPkts256to511Octets", 0x1b0		},
+	{ "RxPkts512to1023Octets", 0x1c0	},
+	{ "RxPkts1024toMaxPktsOctets", 0x1d0	},
+	{ "RxOversizePkts",	0x1e0		},
+	{ "RxJabbers",		0x1f0		},
+	{ "RxAlignmentErrors",	0x200		},
+	{ "RxFCSErrors",	0x210		},
+	{ "RxGoodOctets",	0x220, 8	},
+	{ "RxDropPkts",		0x240		},
+	{ "RxUnicastPkts",	0x250		},
+	{ "RxMulticastPkts",	0x260		},
+	{ "RxBroadcastPkts",	0x270		},
+	{ "RxSAChanges",	0x280		},
+	{ "RxFragments",	0x290		},
+	{ "RxJumboPkt",		0x2a0		},
+	{ "RxSymblErr",		0x2b0		},
+	{ "InRangeErrCount",	0x2c0		},
+	{ "OutRangeErrCount",	0x2d0		},
+	{ "EEELpiEvent",	0x2e0		},
+	{ "EEELpiDuration",	0x2f0		},
+	{ "RxDiscard",		0x300, 8	},
+	{ "TxQPKTQ6",		0x320		},
+	{ "TxQPKTQ7",		0x330		},
+	{ "TxPkts64Octets",	0x340		},
+	{ "TxPkts65to127Octets", 0x350		},
+	{ "TxPkts128to255Octets", 0x360		},
+	{ "TxPkts256to511Ocets", 0x370		},
+	{ "TxPkts512to1023Ocets", 0x380		},
+	{ "TxPkts1024toMaxPktOcets", 0x390	},
+};
+
+#define BCM_SF2_STATS_SIZE	ARRAY_SIZE(bcm_sf2_mib)
+
+static void bcm_sf2_sw_get_strings(struct dsa_switch *ds,
+				   int port, uint8_t *data)
+{
+	unsigned int i;
+
+	for (i = 0; i < BCM_SF2_STATS_SIZE; i++)
+		memcpy(data + i * ETH_GSTRING_LEN,
+		       bcm_sf2_mib[i].string, ETH_GSTRING_LEN);
+}
+
+static void bcm_sf2_sw_get_ethtool_stats(struct dsa_switch *ds,
+					 int port, uint64_t *data)
+{
+	struct bcm_sf2_priv *priv = ds_to_priv(ds);
+	const struct bcm_sf2_hw_stats *s;
+	unsigned int i;
+	u64 val = 0;
+	u32 offset;
+
+	mutex_lock(&priv->stats_mutex);
+
+	/* Now fetch the per-port counters */
+	for (i = 0; i < BCM_SF2_STATS_SIZE; i++) {
+		s = &bcm_sf2_mib[i];
+
+		/* Do a latched 64-bit read if needed */
+		offset = s->reg + CORE_P_MIB_OFFSET(port);
+		if (s->sizeof_stat == 8)
+			val = core_readq(priv, offset);
+		else
+			val = core_readl(priv, offset);
+
+		data[i] = (u64)val;
+	}
+
+	mutex_unlock(&priv->stats_mutex);
+}
+
+static int bcm_sf2_sw_get_sset_count(struct dsa_switch *ds)
+{
+	return BCM_SF2_STATS_SIZE;
+}
+
+static char *bcm_sf2_sw_probe(struct mii_bus *bus, int sw_addr)
+{
+	return "Broadcom Starfighter 2";
+}
+
+static void bcm_sf2_imp_setup(struct dsa_switch *ds, int port)
+{
+	struct bcm_sf2_priv *priv = ds_to_priv(ds);
+	unsigned int i;
+	u32 reg, val;
+
+	/* Enable the port memories */
+	reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL);
+	reg &= ~P_TXQ_PSM_VDD(port);
+	core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
+
+	/* Enable Broadcast, Multicast, Unicast forwarding to IMP port */
+	reg = core_readl(priv, CORE_IMP_CTL);
+	reg |= (RX_BCST_EN | RX_MCST_EN | RX_UCST_EN);
+	reg &= ~(RX_DIS | TX_DIS);
+	core_writel(priv, reg, CORE_IMP_CTL);
+
+	/* Enable forwarding */
+	core_writel(priv, SW_FWDG_EN, CORE_SWMODE);
+
+	/* Enable IMP port in dumb mode */
+	reg = core_readl(priv, CORE_SWITCH_CTRL);
+	reg |= MII_DUMB_FWDG_EN;
+	core_writel(priv, reg, CORE_SWITCH_CTRL);
+
+	/* Resolve which bit controls the Broadcom tag */
+	switch (port) {
+	case 8:
+		val = BRCM_HDR_EN_P8;
+		break;
+	case 7:
+		val = BRCM_HDR_EN_P7;
+		break;
+	case 5:
+		val = BRCM_HDR_EN_P5;
+		break;
+	default:
+		val = 0;
+		break;
+	}
+
+	/* Enable Broadcom tags for IMP port */
+	reg = core_readl(priv, CORE_BRCM_HDR_CTRL);
+	reg |= val;
+	core_writel(priv, reg, CORE_BRCM_HDR_CTRL);
+
+	/* Enable reception Broadcom tag for CPU TX (switch RX) to
+	 * allow us to tag outgoing frames
+	 */
+	reg = core_readl(priv, CORE_BRCM_HDR_RX_DIS);
+	reg &= ~(1 << port);
+	core_writel(priv, reg, CORE_BRCM_HDR_RX_DIS);
+
+	/* Enable transmission of Broadcom tags from the switch (CPU RX) to
+	 * allow delivering frames to the per-port net_devices
+	 */
+	reg = core_readl(priv, CORE_BRCM_HDR_TX_DIS);
+	reg &= ~(1 << port);
+	core_writel(priv, reg, CORE_BRCM_HDR_TX_DIS);
+
+	/* Force link status for IMP port */
+	reg = core_readl(priv, CORE_STS_OVERRIDE_IMP);
+	reg |= (MII_SW_OR | LINK_STS);
+	core_writel(priv, reg, CORE_STS_OVERRIDE_IMP);
+
+	/* Enable the IMP Port to be in the same VLAN as the other ports
+	 * on a per-port basis such that we only have Port i and IMP in
+	 * the same VLAN.
+	 */
+	for (i = 0; i < priv->hw_params.num_ports; i++) {
+		if (!((1 << i) & ds->phys_port_mask))
+			continue;
+
+		reg = core_readl(priv, CORE_PORT_VLAN_CTL_PORT(i));
+		reg |= (1 << port);
+		core_writel(priv, reg, CORE_PORT_VLAN_CTL_PORT(i));
+	}
+}
+
+static void bcm_sf2_port_setup(struct dsa_switch *ds, int port)
+{
+	struct bcm_sf2_priv *priv = ds_to_priv(ds);
+	u32 reg;
+
+	/* Clear the memory power down */
+	reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL);
+	reg &= ~P_TXQ_PSM_VDD(port);
+	core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
+
+	/* Clear the Rx and Tx disable bits and set to no spanning tree */
+	core_writel(priv, 0, CORE_G_PCTL_PORT(port));
+
+	/* Enable port 7 interrupts to get notified */
+	if (port == 7)
+		intrl2_1_mask_clear(priv, P_IRQ_MASK(P7_IRQ_OFF));
+
+	/* Set this port, and only this one to be in the default VLAN */
+	reg = core_readl(priv, CORE_PORT_VLAN_CTL_PORT(port));
+	reg &= ~PORT_VLAN_CTRL_MASK;
+	reg |= (1 << port);
+	core_writel(priv, reg, CORE_PORT_VLAN_CTL_PORT(port));
+}
+
+static void bcm_sf2_port_disable(struct dsa_switch *ds, int port)
+{
+	struct bcm_sf2_priv *priv = ds_to_priv(ds);
+	u32 off, reg;
+
+	if (dsa_is_cpu_port(ds, port))
+		off = CORE_IMP_CTL;
+	else
+		off = CORE_G_PCTL_PORT(port);
+
+	reg = core_readl(priv, off);
+	reg |= RX_DIS | TX_DIS;
+	core_writel(priv, reg, off);
+
+	/* Power down the port memory */
+	reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL);
+	reg |= P_TXQ_PSM_VDD(port);
+	core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
+}
+
+static irqreturn_t bcm_sf2_switch_0_isr(int irq, void *dev_id)
+{
+	struct bcm_sf2_priv *priv = dev_id;
+
+	priv->irq0_stat = intrl2_0_readl(priv, INTRL2_CPU_STATUS) &
+				~priv->irq0_mask;
+	intrl2_0_writel(priv, priv->irq0_stat, INTRL2_CPU_CLEAR);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t bcm_sf2_switch_1_isr(int irq, void *dev_id)
+{
+	struct bcm_sf2_priv *priv = dev_id;
+
+	priv->irq1_stat = intrl2_1_readl(priv, INTRL2_CPU_STATUS) &
+				~priv->irq1_mask;
+	intrl2_1_writel(priv, priv->irq1_stat, INTRL2_CPU_CLEAR);
+
+	if (priv->irq1_stat & P_LINK_UP_IRQ(P7_IRQ_OFF))
+		priv->port_sts[7].link = 1;
+	if (priv->irq1_stat & P_LINK_DOWN_IRQ(P7_IRQ_OFF))
+		priv->port_sts[7].link = 0;
+
+	return IRQ_HANDLED;
+}
+
+static int bcm_sf2_sw_setup(struct dsa_switch *ds)
+{
+	const char *reg_names[BCM_SF2_REGS_NUM] = BCM_SF2_REGS_NAME;
+	struct bcm_sf2_priv *priv = ds_to_priv(ds);
+	struct device_node *dn;
+	void __iomem **base;
+	unsigned int port;
+	unsigned int i;
+	u32 reg, rev;
+	int ret;
+
+	spin_lock_init(&priv->indir_lock);
+	mutex_init(&priv->stats_mutex);
+
+	/* All the interesting properties are at the parent device_node
+	 * level
+	 */
+	dn = ds->pd->of_node->parent;
+
+	priv->irq0 = irq_of_parse_and_map(dn, 0);
+	priv->irq1 = irq_of_parse_and_map(dn, 1);
+
+	base = &priv->core;
+	for (i = 0; i < BCM_SF2_REGS_NUM; i++) {
+		*base = of_iomap(dn, i);
+		if (*base == NULL) {
+			pr_err("unable to find register: %s\n", reg_names[i]);
+			return -ENODEV;
+		}
+		base++;
+	}
+
+	/* Disable all interrupts and request them */
+	intrl2_0_writel(priv, 0xffffffff, INTRL2_CPU_MASK_SET);
+	intrl2_0_writel(priv, 0xffffffff, INTRL2_CPU_CLEAR);
+	intrl2_0_writel(priv, 0, INTRL2_CPU_MASK_CLEAR);
+	intrl2_1_writel(priv, 0xffffffff, INTRL2_CPU_MASK_SET);
+	intrl2_1_writel(priv, 0xffffffff, INTRL2_CPU_CLEAR);
+	intrl2_1_writel(priv, 0, INTRL2_CPU_MASK_CLEAR);
+
+	ret = request_irq(priv->irq0, bcm_sf2_switch_0_isr, 0,
+			  "switch_0", priv);
+	if (ret < 0) {
+		pr_err("failed to request switch_0 IRQ\n");
+		goto out_unmap;
+	}
+
+	ret = request_irq(priv->irq1, bcm_sf2_switch_1_isr, 0,
+			  "switch_1", priv);
+	if (ret < 0) {
+		pr_err("failed to request switch_1 IRQ\n");
+		goto out_free_irq0;
+	}
+
+	/* Reset the MIB counters */
+	reg = core_readl(priv, CORE_GMNCFGCFG);
+	reg |= RST_MIB_CNT;
+	core_writel(priv, reg, CORE_GMNCFGCFG);
+	reg &= ~RST_MIB_CNT;
+	core_writel(priv, reg, CORE_GMNCFGCFG);
+
+	/* Get the maximum number of ports for this switch */
+	priv->hw_params.num_ports = core_readl(priv, CORE_IMP0_PRT_ID) + 1;
+	if (priv->hw_params.num_ports > DSA_MAX_PORTS)
+		priv->hw_params.num_ports = DSA_MAX_PORTS;
+
+	/* Assume a single GPHY setup if we can't read that property */
+	if (of_property_read_u32(dn, "brcm,num-gphy",
+				 &priv->hw_params.num_gphy))
+		priv->hw_params.num_gphy = 1;
+
+	/* Enable all valid ports and disable those unused */
+	for (port = 0; port < priv->hw_params.num_ports; port++) {
+		/* IMP port receives special treatment */
+		if ((1 << port) & ds->phys_port_mask)
+			bcm_sf2_port_setup(ds, port);
+		else if (dsa_is_cpu_port(ds, port))
+			bcm_sf2_imp_setup(ds, port);
+		else
+			bcm_sf2_port_disable(ds, port);
+	}
+
+	/* Include the pseudo-PHY address and the broadcast PHY address to
+	 * divert reads towards our workaround
+	 */
+	ds->phys_mii_mask |= ((1 << 30) | (1 << 0));
+
+	rev = reg_readl(priv, REG_SWITCH_REVISION);
+	priv->hw_params.top_rev = (rev >> SWITCH_TOP_REV_SHIFT) &
+					SWITCH_TOP_REV_MASK;
+	priv->hw_params.core_rev = (rev & SF2_REV_MASK);
+
+	pr_info("Starfighter 2 top: %x.%02x, core: %x.%02x base: 0x%p, IRQs: %d, %d\n",
+		priv->hw_params.top_rev >> 8, priv->hw_params.top_rev & 0xff,
+		priv->hw_params.core_rev >> 8, priv->hw_params.core_rev & 0xff,
+		priv->core, priv->irq0, priv->irq1);
+
+	return 0;
+
+out_free_irq0:
+	free_irq(priv->irq0, priv);
+out_unmap:
+	base = &priv->core;
+	for (i = 0; i < BCM_SF2_REGS_NUM; i++) {
+		iounmap(*base);
+		base++;
+	}
+	return ret;
+}
+
+static int bcm_sf2_sw_set_addr(struct dsa_switch *ds, u8 *addr)
+{
+	return 0;
+}
+
+static int bcm_sf2_sw_indir_rw(struct dsa_switch *ds, int op, int addr,
+			       int regnum, u16 val)
+{
+	struct bcm_sf2_priv *priv = ds_to_priv(ds);
+	int ret = 0;
+	u32 reg;
+
+	reg = reg_readl(priv, REG_SWITCH_CNTRL);
+	reg |= MDIO_MASTER_SEL;
+	reg_writel(priv, reg, REG_SWITCH_CNTRL);
+
+	/* Page << 8 | offset */
+	reg = 0x70;
+	reg <<= 2;
+	core_writel(priv, addr, reg);
+
+	/* Page << 8 | offset */
+	reg = 0x80 << 8 | regnum << 1;
+	reg <<= 2;
+
+	if (op)
+		ret = core_readl(priv, reg);
+	else
+		core_writel(priv, val, reg);
+
+	reg = reg_readl(priv, REG_SWITCH_CNTRL);
+	reg &= ~MDIO_MASTER_SEL;
+	reg_writel(priv, reg, REG_SWITCH_CNTRL);
+
+	return ret & 0xffff;
+}
+
+static int bcm_sf2_sw_phy_read(struct dsa_switch *ds, int addr, int regnum)
+{
+	/* Intercept reads from the MDIO broadcast address or Broadcom
+	 * pseudo-PHY address
+	 */
+	switch (addr) {
+	case 0:
+	case 30:
+		return bcm_sf2_sw_indir_rw(ds, 1, addr, regnum, 0);
+	default:
+		return 0xffff;
+	}
+}
+
+static int bcm_sf2_sw_phy_write(struct dsa_switch *ds, int addr, int regnum,
+				u16 val)
+{
+	/* Intercept writes to the MDIO broadcast address or Broadcom
+	 * pseudo-PHY address
+	 */
+	switch (addr) {
+	case 0:
+	case 30:
+		bcm_sf2_sw_indir_rw(ds, 0, addr, regnum, val);
+		break;
+	}
+
+	return 0;
+}
+
+static void bcm_sf2_sw_adjust_link(struct dsa_switch *ds, int port,
+				   struct phy_device *phydev)
+{
+	struct bcm_sf2_priv *priv = ds_to_priv(ds);
+	u32 id_mode_dis = 0, port_mode;
+	const char *str = NULL;
+	u32 reg;
+
+	switch (phydev->interface) {
+	case PHY_INTERFACE_MODE_RGMII:
+		str = "RGMII (no delay)";
+		id_mode_dis = 1;
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		if (!str)
+			str = "RGMII (TX delay)";
+		port_mode = EXT_GPHY;
+		break;
+	case PHY_INTERFACE_MODE_MII:
+		str = "MII";
+		port_mode = EXT_EPHY;
+		break;
+	case PHY_INTERFACE_MODE_REVMII:
+		str = "Reverse MII";
+		port_mode = EXT_REVMII;
+		break;
+	default:
+		goto force_link;
+	}
+
+	/* Clear id_mode_dis bit, and the existing port mode, but
+	 * make sure we enable the RGMII block for data to pass
+	 */
+	reg = reg_readl(priv, REG_RGMII_CNTRL_P(port));
+	reg &= ~ID_MODE_DIS;
+	reg &= ~(PORT_MODE_MASK << PORT_MODE_SHIFT);
+	reg &= ~(RX_PAUSE_EN | TX_PAUSE_EN);
+
+	reg |= port_mode | RGMII_MODE_EN;
+	if (id_mode_dis)
+		reg |= ID_MODE_DIS;
+
+	if (phydev->pause) {
+		if (phydev->asym_pause)
+			reg |= TX_PAUSE_EN;
+		reg |= RX_PAUSE_EN;
+	}
+
+	reg_writel(priv, reg, REG_RGMII_CNTRL_P(port));
+
+	pr_info("Port %d configured for %s\n", port, str);
+
+force_link:
+	/* Force link settings detected from the PHY */
+	reg = SW_OVERRIDE;
+	switch (phydev->speed) {
+	case SPEED_1000:
+		reg |= SPDSTS_1000 << SPEED_SHIFT;
+		break;
+	case SPEED_100:
+		reg |= SPDSTS_100 << SPEED_SHIFT;
+		break;
+	}
+
+	if (phydev->link)
+		reg |= LINK_STS;
+	if (phydev->duplex == DUPLEX_FULL)
+		reg |= DUPLX_MODE;
+
+	core_writel(priv, reg, CORE_STS_OVERRIDE_GMIIP_PORT(port));
+}
+
+static void bcm_sf2_sw_fixed_link_update(struct dsa_switch *ds, int port,
+					 struct fixed_phy_status *status)
+{
+	struct bcm_sf2_priv *priv = ds_to_priv(ds);
+	u32 link, duplex, pause, speed;
+	u32 reg;
+
+	link = core_readl(priv, CORE_LNKSTS);
+	duplex = core_readl(priv, CORE_DUPSTS);
+	pause = core_readl(priv, CORE_PAUSESTS);
+	speed = core_readl(priv, CORE_SPDSTS);
+
+	speed >>= (port * SPDSTS_SHIFT);
+	speed &= SPDSTS_MASK;
+
+	status->link = 0;
+
+	/* Port 7 is special as we do not get link status from CORE_LNKSTS,
+	 * which means that we need to force the link at the port override
+	 * level to get the data to flow. We do use what the interrupt handler
+	 * did determine before.
+	 */
+	if (port == 7) {
+		status->link = priv->port_sts[port].link;
+		reg = core_readl(priv, CORE_STS_OVERRIDE_GMIIP_PORT(7));
+		reg |= SW_OVERRIDE;
+		if (status->link)
+			reg |= LINK_STS;
+		else
+			reg &= ~LINK_STS;
+		core_writel(priv, reg, CORE_STS_OVERRIDE_GMIIP_PORT(7));
+		status->duplex = 1;
+	} else {
+		status->link = !!(link & (1 << port));
+		status->duplex = !!(duplex & (1 << port));
+	}
+
+	switch (speed) {
+	case SPDSTS_10:
+		status->speed = SPEED_10;
+		break;
+	case SPDSTS_100:
+		status->speed = SPEED_100;
+		break;
+	case SPDSTS_1000:
+		status->speed = SPEED_1000;
+		break;
+	}
+
+	if ((pause & (1 << port)) &&
+	    (pause & (1 << (port + PAUSESTS_TX_PAUSE_SHIFT)))) {
+		status->asym_pause = 1;
+		status->pause = 1;
+	}
+
+	if (pause & (1 << port))
+		status->pause = 1;
+}
+
+static struct dsa_switch_driver bcm_sf2_switch_driver = {
+	.tag_protocol		= htons(ETH_P_BRCMTAG),
+	.priv_size		= sizeof(struct bcm_sf2_priv),
+	.probe			= bcm_sf2_sw_probe,
+	.setup			= bcm_sf2_sw_setup,
+	.set_addr		= bcm_sf2_sw_set_addr,
+	.phy_read		= bcm_sf2_sw_phy_read,
+	.phy_write		= bcm_sf2_sw_phy_write,
+	.get_strings		= bcm_sf2_sw_get_strings,
+	.get_ethtool_stats	= bcm_sf2_sw_get_ethtool_stats,
+	.get_sset_count		= bcm_sf2_sw_get_sset_count,
+	.adjust_link		= bcm_sf2_sw_adjust_link,
+	.fixed_link_update	= bcm_sf2_sw_fixed_link_update,
+};
+
+static int __init bcm_sf2_init(void)
+{
+	register_switch_driver(&bcm_sf2_switch_driver);
+
+	return 0;
+}
+module_init(bcm_sf2_init);
+
+static void __exit bcm_sf2_exit(void)
+{
+	unregister_switch_driver(&bcm_sf2_switch_driver);
+}
+module_exit(bcm_sf2_exit);
+
+MODULE_AUTHOR("Broadcom Corporation");
+MODULE_DESCRIPTION("Driver for Broadcom Starfighter 2 ethernet switch chip");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:brcm-sf2");
diff --git a/drivers/net/dsa/bcm_sf2.h b/drivers/net/dsa/bcm_sf2.h
new file mode 100644
index 0000000..260bab3
--- /dev/null
+++ b/drivers/net/dsa/bcm_sf2.h
@@ -0,0 +1,140 @@
+/*
+ * Broadcom Starfighter2 private context
+ *
+ * Copyright (C) 2014, Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __BCM_SF2_H
+#define __BCM_SF2_H
+
+#include <linux/platform_device.h>
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <linux/spinlock.h>
+#include <linux/mutex.h>
+#include <linux/mii.h>
+
+#include <net/dsa.h>
+
+#include "bcm_sf2_regs.h"
+
+struct bcm_sf2_hw_params {
+	u16	top_rev;
+	u16	core_rev;
+	u32	num_gphy;
+	u8	num_acb_queue;
+	u8	num_rgmii;
+	u8	num_ports;
+	u8	fcb_pause_override:1;
+	u8	acb_packets_inflight:1;
+};
+
+#define BCM_SF2_REGS_NAME {\
+	"core", "reg", "intrl2_0", "intrl2_1", "fcb", "acb" \
+}
+
+#define BCM_SF2_REGS_NUM	6
+
+struct bcm_sf2_port_status {
+	unsigned int link;
+};
+
+struct bcm_sf2_priv {
+	/* Base registers, keep those in order with BCM_SF2_REGS_NAME */
+	void __iomem			*core;
+	void __iomem			*reg;
+	void __iomem			*intrl2_0;
+	void __iomem			*intrl2_1;
+	void __iomem			*fcb;
+	void __iomem			*acb;
+
+	/* spinlock protecting access to the indirect registers */
+	spinlock_t			indir_lock;
+
+	int				irq0;
+	int				irq1;
+	u32				irq0_stat;
+	u32				irq0_mask;
+	u32				irq1_stat;
+	u32				irq1_mask;
+
+	/* Mutex protecting access to the MIB counters */
+	struct mutex			stats_mutex;
+
+	struct bcm_sf2_hw_params	hw_params;
+
+	struct bcm_sf2_port_status	port_sts[DSA_MAX_PORTS];
+};
+
+struct bcm_sf2_hw_stats {
+	const char	*string;
+	u16		reg;
+	u8		sizeof_stat;
+};
+
+#define SF2_IO_MACRO(name) \
+static inline u32 name##_readl(struct bcm_sf2_priv *priv, u32 off)	\
+{									\
+	return __raw_readl(priv->name + off);				\
+}									\
+static inline void name##_writel(struct bcm_sf2_priv *priv,		\
+				  u32 val, u32 off)			\
+{									\
+	__raw_writel(val, priv->name + off);				\
+}									\
+
+/* Accesses to 64-bits register requires us to latch the hi/lo pairs
+ * using the REG_DIR_DATA_{READ,WRITE} ancillary registers. The 'indir_lock'
+ * spinlock is automatically grabbed and released to provide relative
+ * atomiticy with latched reads/writes.
+ */
+#define SF2_IO64_MACRO(name) \
+static inline u64 name##_readq(struct bcm_sf2_priv *priv, u32 off)	\
+{									\
+	u32 indir, dir;							\
+	spin_lock(&priv->indir_lock);					\
+	indir = reg_readl(priv, REG_DIR_DATA_READ);			\
+	dir = __raw_readl(priv->name + off);				\
+	spin_unlock(&priv->indir_lock);					\
+	return (u64)indir << 32 | dir;					\
+}									\
+static inline void name##_writeq(struct bcm_sf2_priv *priv, u32 off,	\
+							u64 val)	\
+{									\
+	spin_lock(&priv->indir_lock);					\
+	reg_writel(priv, upper_32_bits(val), REG_DIR_DATA_WRITE);	\
+	__raw_writel(lower_32_bits(val), priv->name + off);		\
+	spin_unlock(&priv->indir_lock);					\
+}
+
+#define SWITCH_INTR_L2(which)						\
+static inline void intrl2_##which##_mask_clear(struct bcm_sf2_priv *priv, \
+						u32 mask)		\
+{									\
+	intrl2_##which##_writel(priv, mask, INTRL2_CPU_MASK_CLEAR);	\
+	priv->irq##which##_mask &= ~(mask);				\
+}									\
+static inline void intrl2_##which##_mask_set(struct bcm_sf2_priv *priv, \
+						u32 mask)		\
+{									\
+	intrl2_## which##_writel(priv, mask, INTRL2_CPU_MASK_SET);	\
+	priv->irq##which##_mask |= (mask);				\
+}									\
+
+SF2_IO_MACRO(core);
+SF2_IO_MACRO(reg);
+SF2_IO64_MACRO(core);
+SF2_IO_MACRO(intrl2_0);
+SF2_IO_MACRO(intrl2_1);
+SF2_IO_MACRO(fcb);
+SF2_IO_MACRO(acb);
+
+SWITCH_INTR_L2(0);
+SWITCH_INTR_L2(1);
+
+#endif /* __BCM_SF2_H */
diff --git a/drivers/net/dsa/bcm_sf2_regs.h b/drivers/net/dsa/bcm_sf2_regs.h
new file mode 100644
index 0000000..885c231
--- /dev/null
+++ b/drivers/net/dsa/bcm_sf2_regs.h
@@ -0,0 +1,227 @@
+/*
+ * Broadcom Starfighter 2 switch register defines
+ *
+ * Copyright (C) 2014, Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef __BCM_SF2_REGS_H
+#define __BCM_SF2_REGS_H
+
+/* Register set relative to 'REG' */
+#define REG_SWITCH_CNTRL		0x00
+#define  MDIO_MASTER_SEL		(1 << 0)
+
+#define REG_SWITCH_STATUS		0x04
+#define REG_DIR_DATA_WRITE		0x08
+#define REG_DIR_DATA_READ		0x0C
+
+#define REG_SWITCH_REVISION		0x18
+#define  SF2_REV_MASK			0xffff
+#define  SWITCH_TOP_REV_SHIFT		16
+#define  SWITCH_TOP_REV_MASK		0xffff
+
+#define REG_PHY_REVISION		0x1C
+
+#define REG_SPHY_CNTRL			0x2C
+#define  IDDQ_BIAS			(1 << 0)
+#define  EXT_PWR_DOWN			(1 << 1)
+#define  FORCE_DLL_EN			(1 << 2)
+#define  IDDQ_GLOBAL_PWR		(1 << 3)
+#define  CK25_DIS			(1 << 4)
+#define  PHY_RESET			(1 << 5)
+#define  PHY_PHYAD_SHIFT		8
+#define  PHY_PHYAD_MASK			0x1F
+
+#define REG_RGMII_0_BASE		0x34
+#define REG_RGMII_CNTRL			0x00
+#define REG_RGMII_IB_STATUS		0x04
+#define REG_RGMII_RX_CLOCK_DELAY_CNTRL	0x08
+#define REG_RGMII_CNTRL_SIZE		0x0C
+#define REG_RGMII_CNTRL_P(x)		(REG_RGMII_0_BASE + \
+					((x) * REG_RGMII_CNTRL_SIZE))
+/* Relative to REG_RGMII_CNTRL */
+#define  RGMII_MODE_EN			(1 << 0)
+#define  ID_MODE_DIS			(1 << 1)
+#define  PORT_MODE_SHIFT		2
+#define  INT_EPHY			(0 << PORT_MODE_SHIFT)
+#define  INT_GPHY			(1 << PORT_MODE_SHIFT)
+#define  EXT_EPHY			(2 << PORT_MODE_SHIFT)
+#define  EXT_GPHY			(3 << PORT_MODE_SHIFT)
+#define  EXT_REVMII			(4 << PORT_MODE_SHIFT)
+#define  PORT_MODE_MASK			0x7
+#define  RVMII_REF_SEL			(1 << 5)
+#define  RX_PAUSE_EN			(1 << 6)
+#define  TX_PAUSE_EN			(1 << 7)
+#define  TX_CLK_STOP_EN			(1 << 8)
+#define  LPI_COUNT_SHIFT		9
+#define  LPI_COUNT_MASK			0x3F
+
+/* Register set relative to 'INTRL2_0' and 'INTRL2_1' */
+#define INTRL2_CPU_STATUS		0x00
+#define INTRL2_CPU_SET			0x04
+#define INTRL2_CPU_CLEAR		0x08
+#define INTRL2_CPU_MASK_STATUS		0x0c
+#define INTRL2_CPU_MASK_SET		0x10
+#define INTRL2_CPU_MASK_CLEAR		0x14
+
+/* Shared INTRL2_0 and INTRL2_ interrupt sources macros */
+#define P_LINK_UP_IRQ(x)		(1 << (0 + (x)))
+#define P_LINK_DOWN_IRQ(x)		(1 << (1 + (x)))
+#define P_ENERGY_ON_IRQ(x)		(1 << (2 + (x)))
+#define P_ENERGY_OFF_IRQ(x)		(1 << (3 + (x)))
+#define P_GPHY_IRQ(x)			(1 << (4 + (x)))
+#define P_NUM_IRQ			5
+#define P_IRQ_MASK(x)			(P_LINK_UP_IRQ((x)) | \
+					 P_LINK_DOWN_IRQ((x)) | \
+					 P_ENERGY_ON_IRQ((x)) | \
+					 P_ENERGY_OFF_IRQ((x)) | \
+					 P_GPHY_IRQ((x)))
+
+/* INTRL2_0 interrupt sources */
+#define P0_IRQ_OFF			0
+#define MEM_DOUBLE_IRQ			(1 << 5)
+#define EEE_LPI_IRQ			(1 << 6)
+#define P5_CPU_WAKE_IRQ			(1 << 7)
+#define P8_CPU_WAKE_IRQ			(1 << 8)
+#define P7_CPU_WAKE_IRQ			(1 << 9)
+#define IEEE1588_IRQ			(1 << 10)
+#define MDIO_ERR_IRQ			(1 << 11)
+#define MDIO_DONE_IRQ			(1 << 12)
+#define GISB_ERR_IRQ			(1 << 13)
+#define UBUS_ERR_IRQ			(1 << 14)
+#define FAILOVER_ON_IRQ			(1 << 15)
+#define FAILOVER_OFF_IRQ		(1 << 16)
+#define TCAM_SOFT_ERR_IRQ		(1 << 17)
+
+/* INTRL2_1 interrupt sources */
+#define P7_IRQ_OFF			0
+#define P_IRQ_OFF(x)			((6 - (x)) * P_NUM_IRQ)
+
+/* Register set relative to 'CORE' */
+#define CORE_G_PCTL_PORT0		0x00000
+#define CORE_G_PCTL_PORT(x)		(CORE_G_PCTL_PORT0 + (x * 0x4))
+#define CORE_IMP_CTL			0x00020
+#define  RX_DIS				(1 << 0)
+#define  TX_DIS				(1 << 1)
+#define  RX_BCST_EN			(1 << 2)
+#define  RX_MCST_EN			(1 << 3)
+#define  RX_UCST_EN			(1 << 4)
+#define  G_MISTP_STATE_SHIFT		5
+#define  G_MISTP_NO_STP			(0 << G_MISTP_STATE_SHIFT)
+#define  G_MISTP_DIS_STATE		(1 << G_MISTP_STATE_SHIFT)
+#define  G_MISTP_BLOCK_STATE		(2 << G_MISTP_STATE_SHIFT)
+#define  G_MISTP_LISTEN_STATE		(3 << G_MISTP_STATE_SHIFT)
+#define  G_MISTP_LEARN_STATE		(4 << G_MISTP_STATE_SHIFT)
+#define  G_MISTP_FWD_STATE		(5 << G_MISTP_STATE_SHIFT)
+#define  G_MISTP_STATE_MASK		0x7
+
+#define CORE_SWMODE			0x0002c
+#define  SW_FWDG_MODE			(1 << 0)
+#define  SW_FWDG_EN			(1 << 1)
+#define  RTRY_LMT_DIS			(1 << 2)
+
+#define CORE_STS_OVERRIDE_IMP		0x00038
+#define  GMII_SPEED_UP_2G		(1 << 6)
+#define  MII_SW_OR			(1 << 7)
+
+#define CORE_NEW_CTRL			0x00084
+#define  IP_MC				(1 << 0)
+#define  OUTRANGEERR_DISCARD		(1 << 1)
+#define  INRANGEERR_DISCARD		(1 << 2)
+#define  CABLE_DIAG_LEN			(1 << 3)
+#define  OVERRIDE_AUTO_PD_WAR		(1 << 4)
+#define  EN_AUTO_PD_WAR			(1 << 5)
+#define  UC_FWD_EN			(1 << 6)
+#define  MC_FWD_EN			(1 << 7)
+
+#define CORE_SWITCH_CTRL		0x00088
+#define  MII_DUMB_FWDG_EN		(1 << 6)
+
+#define CORE_SFT_LRN_CTRL		0x000f8
+#define  SW_LEARN_CNTL(x)		(1 << (x))
+
+#define CORE_STS_OVERRIDE_GMIIP_PORT(x)	(0x160 + (x) * 4)
+#define  LINK_STS			(1 << 0)
+#define  DUPLX_MODE			(1 << 1)
+#define  SPEED_SHIFT			2
+#define  SPEED_MASK			0x3
+#define  RXFLOW_CNTL			(1 << 4)
+#define  TXFLOW_CNTL			(1 << 5)
+#define  SW_OVERRIDE			(1 << 6)
+
+#define CORE_WATCHDOG_CTRL		0x001e4
+#define  SOFTWARE_RESET			(1 << 7)
+#define  EN_CHIP_RST			(1 << 6)
+#define  EN_SW_RESET			(1 << 4)
+
+#define CORE_LNKSTS			0x00400
+#define  LNK_STS_MASK			0x1ff
+
+#define CORE_SPDSTS			0x00410
+#define  SPDSTS_10			0
+#define  SPDSTS_100			1
+#define  SPDSTS_1000			2
+#define  SPDSTS_SHIFT			2
+#define  SPDSTS_MASK			0x3
+
+#define CORE_DUPSTS			0x00420
+#define  CORE_DUPSTS_MASK		0x1ff
+
+#define CORE_PAUSESTS			0x00428
+#define  PAUSESTS_TX_PAUSE_SHIFT	9
+
+#define CORE_GMNCFGCFG			0x0800
+#define  RST_MIB_CNT			(1 << 0)
+#define  RXBPDU_EN			(1 << 1)
+
+#define CORE_IMP0_PRT_ID		0x0804
+
+#define CORE_BRCM_HDR_CTRL		0x0080c
+#define  BRCM_HDR_EN_P8			(1 << 0)
+#define  BRCM_HDR_EN_P5			(1 << 1)
+#define  BRCM_HDR_EN_P7			(1 << 2)
+
+#define CORE_BRCM_HDR_CTRL2		0x0828
+
+#define CORE_HL_PRTC_CTRL		0x0940
+#define  ARP_EN				(1 << 0)
+#define  RARP_EN			(1 << 1)
+#define  DHCP_EN			(1 << 2)
+#define  ICMPV4_EN			(1 << 3)
+#define  ICMPV6_EN			(1 << 4)
+#define  ICMPV6_FWD_MODE		(1 << 5)
+#define  IGMP_DIP_EN			(1 << 8)
+#define  IGMP_RPTLVE_EN			(1 << 9)
+#define  IGMP_RTPLVE_FWD_MODE		(1 << 10)
+#define  IGMP_QRY_EN			(1 << 11)
+#define  IGMP_QRY_FWD_MODE		(1 << 12)
+#define  IGMP_UKN_EN			(1 << 13)
+#define  IGMP_UKN_FWD_MODE		(1 << 14)
+#define  MLD_RPTDONE_EN			(1 << 15)
+#define  MLD_RPTDONE_FWD_MODE		(1 << 16)
+#define  MLD_QRY_EN			(1 << 17)
+#define  MLD_QRY_FWD_MODE		(1 << 18)
+
+#define CORE_RST_MIB_CNT_EN		0x0950
+
+#define CORE_BRCM_HDR_RX_DIS		0x0980
+#define CORE_BRCM_HDR_TX_DIS		0x0988
+
+#define CORE_MEM_PSM_VDD_CTRL		0x2380
+#define  P_TXQ_PSM_VDD_SHIFT		2
+#define  P_TXQ_PSM_VDD_MASK		0x3
+#define  P_TXQ_PSM_VDD(x)		(P_TXQ_PSM_VDD_MASK << \
+					((x) * P_TXQ_PSM_VDD_SHIFT))
+
+#define	CORE_P0_MIB_OFFSET		0x8000
+#define P_MIB_SIZE			0x400
+#define CORE_P_MIB_OFFSET(x)		(CORE_P0_MIB_OFFSET + (x) * P_MIB_SIZE)
+
+#define CORE_PORT_VLAN_CTL_PORT(x)	(0xc400 + ((x) * 0x8))
+#define  PORT_VLAN_CTRL_MASK		0x1ff
+
+#endif /* __BCM_SF2_REGS_H */
diff --git a/drivers/net/ethernet/arc/Kconfig b/drivers/net/ethernet/arc/Kconfig
index 514c57f..89e04fd 100644
--- a/drivers/net/ethernet/arc/Kconfig
+++ b/drivers/net/ethernet/arc/Kconfig
@@ -17,10 +17,14 @@
 
 if NET_VENDOR_ARC
 
-config ARC_EMAC
-	tristate "ARC EMAC support"
+config ARC_EMAC_CORE
+	tristate
 	select MII
 	select PHYLIB
+
+config ARC_EMAC
+	tristate "ARC EMAC support"
+	select ARC_EMAC_CORE
 	depends on OF_IRQ
 	depends on OF_NET
 	---help---
diff --git a/drivers/net/ethernet/arc/Makefile b/drivers/net/ethernet/arc/Makefile
index 00c8657..241bb80 100644
--- a/drivers/net/ethernet/arc/Makefile
+++ b/drivers/net/ethernet/arc/Makefile
@@ -3,4 +3,5 @@
 #
 
 arc_emac-objs := emac_main.o emac_mdio.o
-obj-$(CONFIG_ARC_EMAC) += arc_emac.o
+obj-$(CONFIG_ARC_EMAC_CORE) += arc_emac.o
+obj-$(CONFIG_ARC_EMAC) += emac_arc.o
diff --git a/drivers/net/ethernet/arc/emac.h b/drivers/net/ethernet/arc/emac.h
index 36cc9bd..eb2ba67 100644
--- a/drivers/net/ethernet/arc/emac.h
+++ b/drivers/net/ethernet/arc/emac.h
@@ -124,6 +124,8 @@
  */
 struct arc_emac_priv {
 	/* Devices */
+	const char *drv_name;
+	const char *drv_version;
 	struct device *dev;
 	struct phy_device *phy_dev;
 	struct mii_bus *bus;
@@ -204,7 +206,9 @@
 	arc_reg_set(priv, reg, value & ~mask);
 }
 
-int arc_mdio_probe(struct platform_device *pdev, struct arc_emac_priv *priv);
+int arc_mdio_probe(struct arc_emac_priv *priv);
 int arc_mdio_remove(struct arc_emac_priv *priv);
+int arc_emac_probe(struct net_device *ndev, int interface);
+int arc_emac_remove(struct net_device *ndev);
 
 #endif /* ARC_EMAC_H */
diff --git a/drivers/net/ethernet/arc/emac_arc.c b/drivers/net/ethernet/arc/emac_arc.c
new file mode 100644
index 0000000..f9cb99b
--- /dev/null
+++ b/drivers/net/ethernet/arc/emac_arc.c
@@ -0,0 +1,95 @@
+/**
+ * emac_arc.c - ARC EMAC specific glue layer
+ *
+ * Copyright (C) 2014 Romain Perier
+ *
+ * Romain Perier  <romain.perier@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/module.h>
+#include <linux/of_net.h>
+#include <linux/platform_device.h>
+
+#include "emac.h"
+
+#define DRV_NAME    "emac_arc"
+#define DRV_VERSION "1.0"
+
+static int emac_arc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct net_device *ndev;
+	struct arc_emac_priv *priv;
+	int interface, err;
+
+	if (!dev->of_node)
+		return -ENODEV;
+
+	ndev = alloc_etherdev(sizeof(struct arc_emac_priv));
+	if (!ndev)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, ndev);
+	SET_NETDEV_DEV(ndev, dev);
+
+	priv = netdev_priv(ndev);
+	priv->drv_name = DRV_NAME;
+	priv->drv_version = DRV_VERSION;
+
+	interface = of_get_phy_mode(dev->of_node);
+	if (interface < 0)
+		interface = PHY_INTERFACE_MODE_MII;
+
+	priv->clk = devm_clk_get(dev, "hclk");
+	if (IS_ERR(priv->clk)) {
+		dev_err(dev, "failed to retrieve host clock from device tree\n");
+		err = -EINVAL;
+		goto out_netdev;
+	}
+
+	err = arc_emac_probe(ndev, interface);
+out_netdev:
+	if (err)
+		free_netdev(ndev);
+	return err;
+}
+
+static int emac_arc_remove(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	int err;
+
+	err = arc_emac_remove(ndev);
+	free_netdev(ndev);
+	return err;
+}
+
+static const struct of_device_id emac_arc_dt_ids[] = {
+	{ .compatible = "snps,arc-emac" },
+	{ /* Sentinel */ }
+};
+
+static struct platform_driver emac_arc_driver = {
+	.probe = emac_arc_probe,
+	.remove = emac_arc_remove,
+	.driver = {
+		.name = DRV_NAME,
+		.of_match_table  = emac_arc_dt_ids,
+	},
+};
+
+module_platform_driver(emac_arc_driver);
+
+MODULE_AUTHOR("Romain Perier <romain.perier@gmail.com>");
+MODULE_DESCRIPTION("ARC EMAC platform driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/ethernet/arc/emac_main.c b/drivers/net/ethernet/arc/emac_main.c
index fe5cfea..b35c69e 100644
--- a/drivers/net/ethernet/arc/emac_main.c
+++ b/drivers/net/ethernet/arc/emac_main.c
@@ -26,8 +26,6 @@
 
 #include "emac.h"
 
-#define DRV_NAME	"arc_emac"
-#define DRV_VERSION	"1.0"
 
 /**
  * arc_emac_adjust_link - Adjust the PHY link duplex.
@@ -120,8 +118,10 @@
 static void arc_emac_get_drvinfo(struct net_device *ndev,
 				 struct ethtool_drvinfo *info)
 {
-	strlcpy(info->driver, DRV_NAME, sizeof(info->driver));
-	strlcpy(info->version, DRV_VERSION, sizeof(info->version));
+	struct arc_emac_priv *priv = netdev_priv(ndev);
+
+	strlcpy(info->driver, priv->drv_name, sizeof(info->driver));
+	strlcpy(info->version, priv->drv_version, sizeof(info->version));
 }
 
 static const struct ethtool_ops arc_emac_ethtool_ops = {
@@ -671,46 +671,38 @@
 #endif
 };
 
-static int arc_emac_probe(struct platform_device *pdev)
+int arc_emac_probe(struct net_device *ndev, int interface)
 {
+	struct device *dev = ndev->dev.parent;
 	struct resource res_regs;
 	struct device_node *phy_node;
 	struct arc_emac_priv *priv;
-	struct net_device *ndev;
 	const char *mac_addr;
 	unsigned int id, clock_frequency, irq;
 	int err;
 
-	if (!pdev->dev.of_node)
-		return -ENODEV;
 
 	/* Get PHY from device tree */
-	phy_node = of_parse_phandle(pdev->dev.of_node, "phy", 0);
+	phy_node = of_parse_phandle(dev->of_node, "phy", 0);
 	if (!phy_node) {
-		dev_err(&pdev->dev, "failed to retrieve phy description from device tree\n");
+		dev_err(dev, "failed to retrieve phy description from device tree\n");
 		return -ENODEV;
 	}
 
 	/* Get EMAC registers base address from device tree */
-	err = of_address_to_resource(pdev->dev.of_node, 0, &res_regs);
+	err = of_address_to_resource(dev->of_node, 0, &res_regs);
 	if (err) {
-		dev_err(&pdev->dev, "failed to retrieve registers base from device tree\n");
+		dev_err(dev, "failed to retrieve registers base from device tree\n");
 		return -ENODEV;
 	}
 
 	/* Get IRQ from device tree */
-	irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
+	irq = irq_of_parse_and_map(dev->of_node, 0);
 	if (!irq) {
-		dev_err(&pdev->dev, "failed to retrieve <irq> value from device tree\n");
+		dev_err(dev, "failed to retrieve <irq> value from device tree\n");
 		return -ENODEV;
 	}
 
-	ndev = alloc_etherdev(sizeof(struct arc_emac_priv));
-	if (!ndev)
-		return -ENOMEM;
-
-	platform_set_drvdata(pdev, ndev);
-	SET_NETDEV_DEV(ndev, &pdev->dev);
 
 	ndev->netdev_ops = &arc_emac_netdev_ops;
 	ndev->ethtool_ops = &arc_emac_ethtool_ops;
@@ -719,60 +711,57 @@
 	ndev->flags &= ~IFF_MULTICAST;
 
 	priv = netdev_priv(ndev);
-	priv->dev = &pdev->dev;
+	priv->dev = dev;
 
-	priv->regs = devm_ioremap_resource(&pdev->dev, &res_regs);
+	priv->regs = devm_ioremap_resource(dev, &res_regs);
 	if (IS_ERR(priv->regs)) {
-		err = PTR_ERR(priv->regs);
-		goto out_netdev;
+		return PTR_ERR(priv->regs);
 	}
-	dev_dbg(&pdev->dev, "Registers base address is 0x%p\n", priv->regs);
+	dev_dbg(dev, "Registers base address is 0x%p\n", priv->regs);
 
-	priv->clk = of_clk_get(pdev->dev.of_node, 0);
-	if (IS_ERR(priv->clk)) {
-		/* Get CPU clock frequency from device tree */
-		if (of_property_read_u32(pdev->dev.of_node, "clock-frequency",
-					&clock_frequency)) {
-			dev_err(&pdev->dev, "failed to retrieve <clock-frequency> from device tree\n");
-			err = -EINVAL;
-			goto out_netdev;
-		}
-	} else {
+	if (priv->clk) {
 		err = clk_prepare_enable(priv->clk);
 		if (err) {
-			dev_err(&pdev->dev, "failed to enable clock\n");
-			goto out_clkget;
+			dev_err(dev, "failed to enable clock\n");
+			return err;
 		}
 
 		clock_frequency = clk_get_rate(priv->clk);
+	} else {
+		/* Get CPU clock frequency from device tree */
+		if (of_property_read_u32(dev->of_node, "clock-frequency",
+					 &clock_frequency)) {
+			dev_err(dev, "failed to retrieve <clock-frequency> from device tree\n");
+			return -EINVAL;
+		}
 	}
 
 	id = arc_reg_get(priv, R_ID);
 
 	/* Check for EMAC revision 5 or 7, magic number */
 	if (!(id == 0x0005fd02 || id == 0x0007fd02)) {
-		dev_err(&pdev->dev, "ARC EMAC not detected, id=0x%x\n", id);
+		dev_err(dev, "ARC EMAC not detected, id=0x%x\n", id);
 		err = -ENODEV;
 		goto out_clken;
 	}
-	dev_info(&pdev->dev, "ARC EMAC detected with id: 0x%x\n", id);
+	dev_info(dev, "ARC EMAC detected with id: 0x%x\n", id);
 
 	/* Set poll rate so that it polls every 1 ms */
 	arc_reg_set(priv, R_POLLRATE, clock_frequency / 1000000);
 
 	ndev->irq = irq;
-	dev_info(&pdev->dev, "IRQ is %d\n", ndev->irq);
+	dev_info(dev, "IRQ is %d\n", ndev->irq);
 
 	/* Register interrupt handler for device */
-	err = devm_request_irq(&pdev->dev, ndev->irq, arc_emac_intr, 0,
+	err = devm_request_irq(dev, ndev->irq, arc_emac_intr, 0,
 			       ndev->name, ndev);
 	if (err) {
-		dev_err(&pdev->dev, "could not allocate IRQ\n");
+		dev_err(dev, "could not allocate IRQ\n");
 		goto out_clken;
 	}
 
 	/* Get MAC address from device tree */
-	mac_addr = of_get_mac_address(pdev->dev.of_node);
+	mac_addr = of_get_mac_address(dev->of_node);
 
 	if (mac_addr)
 		memcpy(ndev->dev_addr, mac_addr, ETH_ALEN);
@@ -780,14 +769,14 @@
 		eth_hw_addr_random(ndev);
 
 	arc_emac_set_address_internal(ndev);
-	dev_info(&pdev->dev, "MAC address is now %pM\n", ndev->dev_addr);
+	dev_info(dev, "MAC address is now %pM\n", ndev->dev_addr);
 
 	/* Do 1 allocation instead of 2 separate ones for Rx and Tx BD rings */
-	priv->rxbd = dmam_alloc_coherent(&pdev->dev, RX_RING_SZ + TX_RING_SZ,
+	priv->rxbd = dmam_alloc_coherent(dev, RX_RING_SZ + TX_RING_SZ,
 					 &priv->rxbd_dma, GFP_KERNEL);
 
 	if (!priv->rxbd) {
-		dev_err(&pdev->dev, "failed to allocate data buffers\n");
+		dev_err(dev, "failed to allocate data buffers\n");
 		err = -ENOMEM;
 		goto out_clken;
 	}
@@ -795,31 +784,31 @@
 	priv->txbd = priv->rxbd + RX_BD_NUM;
 
 	priv->txbd_dma = priv->rxbd_dma + RX_RING_SZ;
-	dev_dbg(&pdev->dev, "EMAC Device addr: Rx Ring [0x%x], Tx Ring[%x]\n",
+	dev_dbg(dev, "EMAC Device addr: Rx Ring [0x%x], Tx Ring[%x]\n",
 		(unsigned int)priv->rxbd_dma, (unsigned int)priv->txbd_dma);
 
-	err = arc_mdio_probe(pdev, priv);
+	err = arc_mdio_probe(priv);
 	if (err) {
-		dev_err(&pdev->dev, "failed to probe MII bus\n");
+		dev_err(dev, "failed to probe MII bus\n");
 		goto out_clken;
 	}
 
 	priv->phy_dev = of_phy_connect(ndev, phy_node, arc_emac_adjust_link, 0,
-				       PHY_INTERFACE_MODE_MII);
+				       interface);
 	if (!priv->phy_dev) {
-		dev_err(&pdev->dev, "of_phy_connect() failed\n");
+		dev_err(dev, "of_phy_connect() failed\n");
 		err = -ENODEV;
 		goto out_mdio;
 	}
 
-	dev_info(&pdev->dev, "connected to %s phy with id 0x%x\n",
+	dev_info(dev, "connected to %s phy with id 0x%x\n",
 		 priv->phy_dev->drv->name, priv->phy_dev->phy_id);
 
 	netif_napi_add(ndev, &priv->napi, arc_emac_poll, ARC_EMAC_NAPI_WEIGHT);
 
 	err = register_netdev(ndev);
 	if (err) {
-		dev_err(&pdev->dev, "failed to register network device\n");
+		dev_err(dev, "failed to register network device\n");
 		goto out_netif_api;
 	}
 
@@ -832,19 +821,15 @@
 out_mdio:
 	arc_mdio_remove(priv);
 out_clken:
-	if (!IS_ERR(priv->clk))
+	if (priv->clk)
 		clk_disable_unprepare(priv->clk);
-out_clkget:
-	if (!IS_ERR(priv->clk))
-		clk_put(priv->clk);
-out_netdev:
-	free_netdev(ndev);
 	return err;
 }
+EXPORT_SYMBOL_GPL(arc_emac_probe);
 
-static int arc_emac_remove(struct platform_device *pdev)
+int arc_emac_remove(struct net_device *ndev)
 {
-	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct device *dev = ndev->dev.parent;
 	struct arc_emac_priv *priv = netdev_priv(ndev);
 
 	phy_disconnect(priv->phy_dev);
@@ -855,31 +840,12 @@
 
 	if (!IS_ERR(priv->clk)) {
 		clk_disable_unprepare(priv->clk);
-		clk_put(priv->clk);
 	}
 
-	free_netdev(ndev);
 
 	return 0;
 }
-
-static const struct of_device_id arc_emac_dt_ids[] = {
-	{ .compatible = "snps,arc-emac" },
-	{ /* Sentinel */ }
-};
-MODULE_DEVICE_TABLE(of, arc_emac_dt_ids);
-
-static struct platform_driver arc_emac_driver = {
-	.probe = arc_emac_probe,
-	.remove = arc_emac_remove,
-	.driver = {
-		.name = DRV_NAME,
-		.owner = THIS_MODULE,
-		.of_match_table  = arc_emac_dt_ids,
-		},
-};
-
-module_platform_driver(arc_emac_driver);
+EXPORT_SYMBOL_GPL(arc_emac_remove);
 
 MODULE_AUTHOR("Alexey Brodkin <abrodkin@synopsys.com>");
 MODULE_DESCRIPTION("ARC EMAC driver");
diff --git a/drivers/net/ethernet/arc/emac_mdio.c b/drivers/net/ethernet/arc/emac_mdio.c
index 26ba242..d5ee986 100644
--- a/drivers/net/ethernet/arc/emac_mdio.c
+++ b/drivers/net/ethernet/arc/emac_mdio.c
@@ -100,7 +100,6 @@
 
 /**
  * arc_mdio_probe - MDIO probe function.
- * @pdev:	Pointer to platform device.
  * @priv:	Pointer to ARC EMAC private data structure.
  *
  * returns:	0 on success, -ENOMEM when mdiobus_alloc
@@ -108,7 +107,7 @@
  *
  * Sets up and registers the MDIO interface.
  */
-int arc_mdio_probe(struct platform_device *pdev, struct arc_emac_priv *priv)
+int arc_mdio_probe(struct arc_emac_priv *priv)
 {
 	struct mii_bus *bus;
 	int error;
@@ -124,9 +123,9 @@
 	bus->read = &arc_mdio_read;
 	bus->write = &arc_mdio_write;
 
-	snprintf(bus->id, MII_BUS_ID_SIZE, "%s", pdev->name);
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s", bus->name);
 
-	error = of_mdiobus_register(bus, pdev->dev.of_node);
+	error = of_mdiobus_register(bus, priv->dev->of_node);
 	if (error) {
 		dev_err(priv->dev, "cannot register MDIO bus %s\n", bus->name);
 		mdiobus_free(bus);
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index 2f394b8..93132d8f 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -985,7 +985,7 @@
 		/* Tx */
 		for_each_cos_in_tx_queue(fp, cos)
 		{
-			if (!fp->txdata_ptr)
+			if (!fp->txdata_ptr[cos])
 				break;
 
 			txdata = *fp->txdata_ptr[cos];
@@ -1140,7 +1140,7 @@
 		for_each_cos_in_tx_queue(fp, cos) {
 			struct bnx2x_fp_txdata *txdata = fp->txdata_ptr[cos];
 
-			if (!fp->txdata_ptr)
+			if (!fp->txdata_ptr[cos])
 				break;
 
 			if (!txdata->tx_cons_sb)
diff --git a/drivers/net/ethernet/dec/tulip/dmfe.c b/drivers/net/ethernet/dec/tulip/dmfe.c
index 322213d..c820560 100644
--- a/drivers/net/ethernet/dec/tulip/dmfe.c
+++ b/drivers/net/ethernet/dec/tulip/dmfe.c
@@ -328,10 +328,10 @@
 static void update_cr6(u32, void __iomem *);
 static void send_filter_frame(struct DEVICE *);
 static void dm9132_id_table(struct DEVICE *);
-static u16 phy_read(void __iomem *, u8, u8, u32);
-static void phy_write(void __iomem *, u8, u8, u16, u32);
-static void phy_write_1bit(void __iomem *, u32);
-static u16 phy_read_1bit(void __iomem *);
+static u16 dmfe_phy_read(void __iomem *, u8, u8, u32);
+static void dmfe_phy_write(void __iomem *, u8, u8, u16, u32);
+static void dmfe_phy_write_1bit(void __iomem *, u32);
+static u16 dmfe_phy_read_1bit(void __iomem *);
 static u8 dmfe_sense_speed(struct dmfe_board_info *);
 static void dmfe_process_mode(struct dmfe_board_info *);
 static void dmfe_timer(unsigned long);
@@ -770,7 +770,7 @@
 	/* Reset & stop DM910X board */
 	dw32(DCR0, DM910X_RESET);
 	udelay(100);
-	phy_write(ioaddr, db->phy_addr, 0, 0x8000, db->chip_id);
+	dmfe_phy_write(ioaddr, db->phy_addr, 0, 0x8000, db->chip_id);
 
 	/* free interrupt */
 	free_irq(db->pdev->irq, dev);
@@ -1154,7 +1154,7 @@
 		if (db->chip_type && (db->chip_id==PCI_DM9102_ID)) {
 			db->cr6_data &= ~0x40000;
 			update_cr6(db->cr6_data, ioaddr);
-			phy_write(ioaddr, db->phy_addr, 0, 0x1000, db->chip_id);
+			dmfe_phy_write(ioaddr, db->phy_addr, 0, 0x1000, db->chip_id);
 			db->cr6_data |= 0x40000;
 			update_cr6(db->cr6_data, ioaddr);
 			db->timer.expires = DMFE_TIMER_WUT + HZ * 2;
@@ -1230,9 +1230,9 @@
 	*/
 
 	/* need a dummy read because of PHY's register latch*/
-	phy_read (db->ioaddr, db->phy_addr, 1, db->chip_id);
-	link_ok_phy = (phy_read (db->ioaddr,
-		       db->phy_addr, 1, db->chip_id) & 0x4) ? 1 : 0;
+	dmfe_phy_read (db->ioaddr, db->phy_addr, 1, db->chip_id);
+	link_ok_phy = (dmfe_phy_read (db->ioaddr,
+				      db->phy_addr, 1, db->chip_id) & 0x4) ? 1 : 0;
 
 	if (link_ok_phy != link_ok) {
 		DMFE_DBUG (0, "PHY and chip report different link status", 0);
@@ -1247,8 +1247,8 @@
 		/* For Force 10/100M Half/Full mode: Enable Auto-Nego mode */
 		/* AUTO or force 1M Homerun/Longrun don't need */
 		if ( !(db->media_mode & 0x38) )
-			phy_write(db->ioaddr, db->phy_addr,
-				  0, 0x1000, db->chip_id);
+			dmfe_phy_write(db->ioaddr, db->phy_addr,
+				       0, 0x1000, db->chip_id);
 
 		/* AUTO mode, if INT phyxcer link failed, select EXT device */
 		if (db->media_mode & DMFE_AUTO) {
@@ -1649,16 +1649,16 @@
 	/* CR6 bit18=0, select 10/100M */
 	update_cr6(db->cr6_data & ~0x40000, ioaddr);
 
-	phy_mode = phy_read(db->ioaddr, db->phy_addr, 1, db->chip_id);
-	phy_mode = phy_read(db->ioaddr, db->phy_addr, 1, db->chip_id);
+	phy_mode = dmfe_phy_read(db->ioaddr, db->phy_addr, 1, db->chip_id);
+	phy_mode = dmfe_phy_read(db->ioaddr, db->phy_addr, 1, db->chip_id);
 
 	if ( (phy_mode & 0x24) == 0x24 ) {
 		if (db->chip_id == PCI_DM9132_ID)	/* DM9132 */
-			phy_mode = phy_read(db->ioaddr,
-				    db->phy_addr, 7, db->chip_id) & 0xf000;
+			phy_mode = dmfe_phy_read(db->ioaddr,
+						 db->phy_addr, 7, db->chip_id) & 0xf000;
 		else 				/* DM9102/DM9102A */
-			phy_mode = phy_read(db->ioaddr,
-				    db->phy_addr, 17, db->chip_id) & 0xf000;
+			phy_mode = dmfe_phy_read(db->ioaddr,
+						 db->phy_addr, 17, db->chip_id) & 0xf000;
 		switch (phy_mode) {
 		case 0x1000: db->op_mode = DMFE_10MHF; break;
 		case 0x2000: db->op_mode = DMFE_10MFD; break;
@@ -1695,15 +1695,15 @@
 
 	/* DM9009 Chip: Phyxcer reg18 bit12=0 */
 	if (db->chip_id == PCI_DM9009_ID) {
-		phy_reg = phy_read(db->ioaddr,
-				   db->phy_addr, 18, db->chip_id) & ~0x1000;
+		phy_reg = dmfe_phy_read(db->ioaddr,
+					db->phy_addr, 18, db->chip_id) & ~0x1000;
 
-		phy_write(db->ioaddr,
-			  db->phy_addr, 18, phy_reg, db->chip_id);
+		dmfe_phy_write(db->ioaddr,
+			       db->phy_addr, 18, phy_reg, db->chip_id);
 	}
 
 	/* Phyxcer capability setting */
-	phy_reg = phy_read(db->ioaddr, db->phy_addr, 4, db->chip_id) & ~0x01e0;
+	phy_reg = dmfe_phy_read(db->ioaddr, db->phy_addr, 4, db->chip_id) & ~0x01e0;
 
 	if (db->media_mode & DMFE_AUTO) {
 		/* AUTO Mode */
@@ -1724,13 +1724,13 @@
 		phy_reg|=db->PHY_reg4;
 		db->media_mode|=DMFE_AUTO;
 	}
-	phy_write(db->ioaddr, db->phy_addr, 4, phy_reg, db->chip_id);
+	dmfe_phy_write(db->ioaddr, db->phy_addr, 4, phy_reg, db->chip_id);
 
  	/* Restart Auto-Negotiation */
 	if ( db->chip_type && (db->chip_id == PCI_DM9102_ID) )
-		phy_write(db->ioaddr, db->phy_addr, 0, 0x1800, db->chip_id);
+		dmfe_phy_write(db->ioaddr, db->phy_addr, 0, 0x1800, db->chip_id);
 	if ( !db->chip_type )
-		phy_write(db->ioaddr, db->phy_addr, 0, 0x1200, db->chip_id);
+		dmfe_phy_write(db->ioaddr, db->phy_addr, 0, 0x1200, db->chip_id);
 }
 
 
@@ -1762,7 +1762,7 @@
 	/* 10/100M phyxcer force mode need */
 	if ( !(db->media_mode & 0x18)) {
 		/* Forece Mode */
-		phy_reg = phy_read(db->ioaddr, db->phy_addr, 6, db->chip_id);
+		phy_reg = dmfe_phy_read(db->ioaddr, db->phy_addr, 6, db->chip_id);
 		if ( !(phy_reg & 0x1) ) {
 			/* parter without N-Way capability */
 			phy_reg = 0x0;
@@ -1772,12 +1772,12 @@
 			case DMFE_100MHF: phy_reg = 0x2000; break;
 			case DMFE_100MFD: phy_reg = 0x2100; break;
 			}
-			phy_write(db->ioaddr,
-				  db->phy_addr, 0, phy_reg, db->chip_id);
+			dmfe_phy_write(db->ioaddr,
+				       db->phy_addr, 0, phy_reg, db->chip_id);
        			if ( db->chip_type && (db->chip_id == PCI_DM9102_ID) )
 				mdelay(20);
-			phy_write(db->ioaddr,
-				  db->phy_addr, 0, phy_reg, db->chip_id);
+			dmfe_phy_write(db->ioaddr,
+				       db->phy_addr, 0, phy_reg, db->chip_id);
 		}
 	}
 }
@@ -1787,8 +1787,8 @@
  *	Write a word to Phy register
  */
 
-static void phy_write(void __iomem *ioaddr, u8 phy_addr, u8 offset,
-		      u16 phy_data, u32 chip_id)
+static void dmfe_phy_write(void __iomem *ioaddr, u8 phy_addr, u8 offset,
+			   u16 phy_data, u32 chip_id)
 {
 	u16 i;
 
@@ -1799,34 +1799,34 @@
 
 		/* Send 33 synchronization clock to Phy controller */
 		for (i = 0; i < 35; i++)
-			phy_write_1bit(ioaddr, PHY_DATA_1);
+			dmfe_phy_write_1bit(ioaddr, PHY_DATA_1);
 
 		/* Send start command(01) to Phy */
-		phy_write_1bit(ioaddr, PHY_DATA_0);
-		phy_write_1bit(ioaddr, PHY_DATA_1);
+		dmfe_phy_write_1bit(ioaddr, PHY_DATA_0);
+		dmfe_phy_write_1bit(ioaddr, PHY_DATA_1);
 
 		/* Send write command(01) to Phy */
-		phy_write_1bit(ioaddr, PHY_DATA_0);
-		phy_write_1bit(ioaddr, PHY_DATA_1);
+		dmfe_phy_write_1bit(ioaddr, PHY_DATA_0);
+		dmfe_phy_write_1bit(ioaddr, PHY_DATA_1);
 
 		/* Send Phy address */
 		for (i = 0x10; i > 0; i = i >> 1)
-			phy_write_1bit(ioaddr,
-				       phy_addr & i ? PHY_DATA_1 : PHY_DATA_0);
+			dmfe_phy_write_1bit(ioaddr,
+					    phy_addr & i ? PHY_DATA_1 : PHY_DATA_0);
 
 		/* Send register address */
 		for (i = 0x10; i > 0; i = i >> 1)
-			phy_write_1bit(ioaddr,
-				       offset & i ? PHY_DATA_1 : PHY_DATA_0);
+			dmfe_phy_write_1bit(ioaddr,
+					    offset & i ? PHY_DATA_1 : PHY_DATA_0);
 
 		/* written trasnition */
-		phy_write_1bit(ioaddr, PHY_DATA_1);
-		phy_write_1bit(ioaddr, PHY_DATA_0);
+		dmfe_phy_write_1bit(ioaddr, PHY_DATA_1);
+		dmfe_phy_write_1bit(ioaddr, PHY_DATA_0);
 
 		/* Write a word data to PHY controller */
 		for ( i = 0x8000; i > 0; i >>= 1)
-			phy_write_1bit(ioaddr,
-				       phy_data & i ? PHY_DATA_1 : PHY_DATA_0);
+			dmfe_phy_write_1bit(ioaddr,
+					    phy_data & i ? PHY_DATA_1 : PHY_DATA_0);
 	}
 }
 
@@ -1835,7 +1835,7 @@
  *	Read a word data from phy register
  */
 
-static u16 phy_read(void __iomem *ioaddr, u8 phy_addr, u8 offset, u32 chip_id)
+static u16 dmfe_phy_read(void __iomem *ioaddr, u8 phy_addr, u8 offset, u32 chip_id)
 {
 	int i;
 	u16 phy_data;
@@ -1848,33 +1848,33 @@
 
 		/* Send 33 synchronization clock to Phy controller */
 		for (i = 0; i < 35; i++)
-			phy_write_1bit(ioaddr, PHY_DATA_1);
+			dmfe_phy_write_1bit(ioaddr, PHY_DATA_1);
 
 		/* Send start command(01) to Phy */
-		phy_write_1bit(ioaddr, PHY_DATA_0);
-		phy_write_1bit(ioaddr, PHY_DATA_1);
+		dmfe_phy_write_1bit(ioaddr, PHY_DATA_0);
+		dmfe_phy_write_1bit(ioaddr, PHY_DATA_1);
 
 		/* Send read command(10) to Phy */
-		phy_write_1bit(ioaddr, PHY_DATA_1);
-		phy_write_1bit(ioaddr, PHY_DATA_0);
+		dmfe_phy_write_1bit(ioaddr, PHY_DATA_1);
+		dmfe_phy_write_1bit(ioaddr, PHY_DATA_0);
 
 		/* Send Phy address */
 		for (i = 0x10; i > 0; i = i >> 1)
-			phy_write_1bit(ioaddr,
-				       phy_addr & i ? PHY_DATA_1 : PHY_DATA_0);
+			dmfe_phy_write_1bit(ioaddr,
+					    phy_addr & i ? PHY_DATA_1 : PHY_DATA_0);
 
 		/* Send register address */
 		for (i = 0x10; i > 0; i = i >> 1)
-			phy_write_1bit(ioaddr,
-				       offset & i ? PHY_DATA_1 : PHY_DATA_0);
+			dmfe_phy_write_1bit(ioaddr,
+					    offset & i ? PHY_DATA_1 : PHY_DATA_0);
 
 		/* Skip transition state */
-		phy_read_1bit(ioaddr);
+		dmfe_phy_read_1bit(ioaddr);
 
 		/* read 16bit data */
 		for (phy_data = 0, i = 0; i < 16; i++) {
 			phy_data <<= 1;
-			phy_data |= phy_read_1bit(ioaddr);
+			phy_data |= dmfe_phy_read_1bit(ioaddr);
 		}
 	}
 
@@ -1886,7 +1886,7 @@
  *	Write one bit data to Phy Controller
  */
 
-static void phy_write_1bit(void __iomem *ioaddr, u32 phy_data)
+static void dmfe_phy_write_1bit(void __iomem *ioaddr, u32 phy_data)
 {
 	dw32(DCR9, phy_data);		/* MII Clock Low */
 	udelay(1);
@@ -1901,7 +1901,7 @@
  *	Read one bit phy data from PHY controller
  */
 
-static u16 phy_read_1bit(void __iomem *ioaddr)
+static u16 dmfe_phy_read_1bit(void __iomem *ioaddr)
 {
 	u16 phy_data;
 
@@ -1995,11 +1995,11 @@
 	/* Check DM9801 or DM9802 present or not */
 	db->HPNA_present = 0;
 	update_cr6(db->cr6_data | 0x40000, db->ioaddr);
-	tmp_reg = phy_read(db->ioaddr, db->phy_addr, 3, db->chip_id);
+	tmp_reg = dmfe_phy_read(db->ioaddr, db->phy_addr, 3, db->chip_id);
 	if ( ( tmp_reg & 0xfff0 ) == 0xb900 ) {
 		/* DM9801 or DM9802 present */
 		db->HPNA_timer = 8;
-		if ( phy_read(db->ioaddr, db->phy_addr, 31, db->chip_id) == 0x4404) {
+		if ( dmfe_phy_read(db->ioaddr, db->phy_addr, 31, db->chip_id) == 0x4404) {
 			/* DM9801 HomeRun */
 			db->HPNA_present = 1;
 			dmfe_program_DM9801(db, tmp_reg);
@@ -2025,29 +2025,29 @@
 	switch(HPNA_rev) {
 	case 0xb900: /* DM9801 E3 */
 		db->HPNA_command |= 0x1000;
-		reg25 = phy_read(db->ioaddr, db->phy_addr, 24, db->chip_id);
+		reg25 = dmfe_phy_read(db->ioaddr, db->phy_addr, 24, db->chip_id);
 		reg25 = ( (reg25 + HPNA_NoiseFloor) & 0xff) | 0xf000;
-		reg17 = phy_read(db->ioaddr, db->phy_addr, 17, db->chip_id);
+		reg17 = dmfe_phy_read(db->ioaddr, db->phy_addr, 17, db->chip_id);
 		break;
 	case 0xb901: /* DM9801 E4 */
-		reg25 = phy_read(db->ioaddr, db->phy_addr, 25, db->chip_id);
+		reg25 = dmfe_phy_read(db->ioaddr, db->phy_addr, 25, db->chip_id);
 		reg25 = (reg25 & 0xff00) + HPNA_NoiseFloor;
-		reg17 = phy_read(db->ioaddr, db->phy_addr, 17, db->chip_id);
+		reg17 = dmfe_phy_read(db->ioaddr, db->phy_addr, 17, db->chip_id);
 		reg17 = (reg17 & 0xfff0) + HPNA_NoiseFloor + 3;
 		break;
 	case 0xb902: /* DM9801 E5 */
 	case 0xb903: /* DM9801 E6 */
 	default:
 		db->HPNA_command |= 0x1000;
-		reg25 = phy_read(db->ioaddr, db->phy_addr, 25, db->chip_id);
+		reg25 = dmfe_phy_read(db->ioaddr, db->phy_addr, 25, db->chip_id);
 		reg25 = (reg25 & 0xff00) + HPNA_NoiseFloor - 5;
-		reg17 = phy_read(db->ioaddr, db->phy_addr, 17, db->chip_id);
+		reg17 = dmfe_phy_read(db->ioaddr, db->phy_addr, 17, db->chip_id);
 		reg17 = (reg17 & 0xfff0) + HPNA_NoiseFloor;
 		break;
 	}
-	phy_write(db->ioaddr, db->phy_addr, 16, db->HPNA_command, db->chip_id);
-	phy_write(db->ioaddr, db->phy_addr, 17, reg17, db->chip_id);
-	phy_write(db->ioaddr, db->phy_addr, 25, reg25, db->chip_id);
+	dmfe_phy_write(db->ioaddr, db->phy_addr, 16, db->HPNA_command, db->chip_id);
+	dmfe_phy_write(db->ioaddr, db->phy_addr, 17, reg17, db->chip_id);
+	dmfe_phy_write(db->ioaddr, db->phy_addr, 25, reg25, db->chip_id);
 }
 
 
@@ -2060,10 +2060,10 @@
 	uint phy_reg;
 
 	if ( !HPNA_NoiseFloor ) HPNA_NoiseFloor = DM9802_NOISE_FLOOR;
-	phy_write(db->ioaddr, db->phy_addr, 16, db->HPNA_command, db->chip_id);
-	phy_reg = phy_read(db->ioaddr, db->phy_addr, 25, db->chip_id);
+	dmfe_phy_write(db->ioaddr, db->phy_addr, 16, db->HPNA_command, db->chip_id);
+	phy_reg = dmfe_phy_read(db->ioaddr, db->phy_addr, 25, db->chip_id);
 	phy_reg = ( phy_reg & 0xff00) + HPNA_NoiseFloor;
-	phy_write(db->ioaddr, db->phy_addr, 25, phy_reg, db->chip_id);
+	dmfe_phy_write(db->ioaddr, db->phy_addr, 25, phy_reg, db->chip_id);
 }
 
 
@@ -2077,7 +2077,7 @@
 	uint phy_reg;
 
 	/* Got remote device status */
-	phy_reg = phy_read(db->ioaddr, db->phy_addr, 17, db->chip_id) & 0x60;
+	phy_reg = dmfe_phy_read(db->ioaddr, db->phy_addr, 17, db->chip_id) & 0x60;
 	switch(phy_reg) {
 	case 0x00: phy_reg = 0x0a00;break; /* LP/LS */
 	case 0x20: phy_reg = 0x0900;break; /* LP/HS */
@@ -2087,8 +2087,8 @@
 
 	/* Check remote device status match our setting ot not */
 	if ( phy_reg != (db->HPNA_command & 0x0f00) ) {
-		phy_write(db->ioaddr, db->phy_addr, 16, db->HPNA_command,
-			  db->chip_id);
+		dmfe_phy_write(db->ioaddr, db->phy_addr, 16, db->HPNA_command,
+			       db->chip_id);
 		db->HPNA_timer=8;
 	} else
 		db->HPNA_timer=600;	/* Match, every 10 minutes, check */
diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c
index 89c29b4..89de7fe 100644
--- a/drivers/net/ethernet/intel/igb/igb_main.c
+++ b/drivers/net/ethernet/intel/igb/igb_main.c
@@ -4813,6 +4813,41 @@
 	tx_desc->read.olinfo_status = cpu_to_le32(olinfo_status);
 }
 
+static int __igb_maybe_stop_tx(struct igb_ring *tx_ring, const u16 size)
+{
+	struct net_device *netdev = tx_ring->netdev;
+
+	netif_stop_subqueue(netdev, tx_ring->queue_index);
+
+	/* Herbert's original patch had:
+	 *  smp_mb__after_netif_stop_queue();
+	 * but since that doesn't exist yet, just open code it.
+	 */
+	smp_mb();
+
+	/* We need to check again in a case another CPU has just
+	 * made room available.
+	 */
+	if (igb_desc_unused(tx_ring) < size)
+		return -EBUSY;
+
+	/* A reprieve! */
+	netif_wake_subqueue(netdev, tx_ring->queue_index);
+
+	u64_stats_update_begin(&tx_ring->tx_syncp2);
+	tx_ring->tx_stats.restart_queue2++;
+	u64_stats_update_end(&tx_ring->tx_syncp2);
+
+	return 0;
+}
+
+static inline int igb_maybe_stop_tx(struct igb_ring *tx_ring, const u16 size)
+{
+	if (igb_desc_unused(tx_ring) >= size)
+		return 0;
+	return __igb_maybe_stop_tx(tx_ring, size);
+}
+
 static void igb_tx_map(struct igb_ring *tx_ring,
 		       struct igb_tx_buffer *first,
 		       const u8 hdr_len)
@@ -4915,7 +4950,10 @@
 
 	tx_ring->next_to_use = i;
 
-	if (!skb->xmit_more) {
+	/* Make sure there is space in the ring for the next send. */
+	igb_maybe_stop_tx(tx_ring, DESC_NEEDED);
+
+	if (netif_xmit_stopped(txring_txq(tx_ring)) || !skb->xmit_more) {
 		writel(i, tx_ring->tail);
 
 		/* we need this if more than one processor can write to our tail
@@ -4942,41 +4980,6 @@
 	tx_ring->next_to_use = i;
 }
 
-static int __igb_maybe_stop_tx(struct igb_ring *tx_ring, const u16 size)
-{
-	struct net_device *netdev = tx_ring->netdev;
-
-	netif_stop_subqueue(netdev, tx_ring->queue_index);
-
-	/* Herbert's original patch had:
-	 *  smp_mb__after_netif_stop_queue();
-	 * but since that doesn't exist yet, just open code it.
-	 */
-	smp_mb();
-
-	/* We need to check again in a case another CPU has just
-	 * made room available.
-	 */
-	if (igb_desc_unused(tx_ring) < size)
-		return -EBUSY;
-
-	/* A reprieve! */
-	netif_wake_subqueue(netdev, tx_ring->queue_index);
-
-	u64_stats_update_begin(&tx_ring->tx_syncp2);
-	tx_ring->tx_stats.restart_queue2++;
-	u64_stats_update_end(&tx_ring->tx_syncp2);
-
-	return 0;
-}
-
-static inline int igb_maybe_stop_tx(struct igb_ring *tx_ring, const u16 size)
-{
-	if (igb_desc_unused(tx_ring) >= size)
-		return 0;
-	return __igb_maybe_stop_tx(tx_ring, size);
-}
-
 netdev_tx_t igb_xmit_frame_ring(struct sk_buff *skb,
 				struct igb_ring *tx_ring)
 {
@@ -5047,9 +5050,6 @@
 
 	igb_tx_map(tx_ring, first, hdr_len);
 
-	/* Make sure there is space in the ring for the next send. */
-	igb_maybe_stop_tx(tx_ring, DESC_NEEDED);
-
 	return NETDEV_TX_OK;
 
 out_drop:
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
index ba9ceaa..53fbf06 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -6837,6 +6837,36 @@
 	tx_desc->read.olinfo_status = cpu_to_le32(olinfo_status);
 }
 
+static int __ixgbe_maybe_stop_tx(struct ixgbe_ring *tx_ring, u16 size)
+{
+	netif_stop_subqueue(tx_ring->netdev, tx_ring->queue_index);
+
+	/* Herbert's original patch had:
+	 *  smp_mb__after_netif_stop_queue();
+	 * but since that doesn't exist yet, just open code it.
+	 */
+	smp_mb();
+
+	/* We need to check again in a case another CPU has just
+	 * made room available.
+	 */
+	if (likely(ixgbe_desc_unused(tx_ring) < size))
+		return -EBUSY;
+
+	/* A reprieve! - use start_queue because it doesn't call schedule */
+	netif_start_subqueue(tx_ring->netdev, tx_ring->queue_index);
+	++tx_ring->tx_stats.restart_queue;
+	return 0;
+}
+
+static inline int ixgbe_maybe_stop_tx(struct ixgbe_ring *tx_ring, u16 size)
+{
+	if (likely(ixgbe_desc_unused(tx_ring) >= size))
+		return 0;
+
+	return __ixgbe_maybe_stop_tx(tx_ring, size);
+}
+
 #define IXGBE_TXD_CMD (IXGBE_TXD_CMD_EOP | \
 		       IXGBE_TXD_CMD_RS)
 
@@ -6958,10 +6988,13 @@
 
 	tx_ring->next_to_use = i;
 
-	if (!skb->xmit_more) {
+	ixgbe_maybe_stop_tx(tx_ring, DESC_NEEDED);
+
+	if (netif_xmit_stopped(txring_txq(tx_ring)) || !skb->xmit_more) {
 		/* notify HW of packet */
 		ixgbe_write_tail(tx_ring, i);
 	}
+
 	return;
 dma_error:
 	dev_err(tx_ring->dev, "TX DMA map failed\n");
@@ -7068,32 +7101,6 @@
 					      input, common, ring->queue_index);
 }
 
-static int __ixgbe_maybe_stop_tx(struct ixgbe_ring *tx_ring, u16 size)
-{
-	netif_stop_subqueue(tx_ring->netdev, tx_ring->queue_index);
-	/* Herbert's original patch had:
-	 *  smp_mb__after_netif_stop_queue();
-	 * but since that doesn't exist yet, just open code it. */
-	smp_mb();
-
-	/* We need to check again in a case another CPU has just
-	 * made room available. */
-	if (likely(ixgbe_desc_unused(tx_ring) < size))
-		return -EBUSY;
-
-	/* A reprieve! - use start_queue because it doesn't call schedule */
-	netif_start_subqueue(tx_ring->netdev, tx_ring->queue_index);
-	++tx_ring->tx_stats.restart_queue;
-	return 0;
-}
-
-static inline int ixgbe_maybe_stop_tx(struct ixgbe_ring *tx_ring, u16 size)
-{
-	if (likely(ixgbe_desc_unused(tx_ring) >= size))
-		return 0;
-	return __ixgbe_maybe_stop_tx(tx_ring, size);
-}
-
 static u16 ixgbe_select_queue(struct net_device *dev, struct sk_buff *skb,
 			      void *accel_priv, select_queue_fallback_t fallback)
 {
@@ -7262,8 +7269,6 @@
 #endif /* IXGBE_FCOE */
 	ixgbe_tx_map(tx_ring, first, hdr_len);
 
-	ixgbe_maybe_stop_tx(tx_ring, DESC_NEEDED);
-
 	return NETDEV_TX_OK;
 
 out_drop:
diff --git a/drivers/net/ethernet/sun/sungem.c b/drivers/net/ethernet/sun/sungem.c
index f7415b6..fef5dec 100644
--- a/drivers/net/ethernet/sun/sungem.c
+++ b/drivers/net/ethernet/sun/sungem.c
@@ -115,7 +115,7 @@
 
 MODULE_DEVICE_TABLE(pci, gem_pci_tbl);
 
-static u16 __phy_read(struct gem *gp, int phy_addr, int reg)
+static u16 __sungem_phy_read(struct gem *gp, int phy_addr, int reg)
 {
 	u32 cmd;
 	int limit = 10000;
@@ -141,18 +141,18 @@
 	return cmd & MIF_FRAME_DATA;
 }
 
-static inline int _phy_read(struct net_device *dev, int mii_id, int reg)
+static inline int _sungem_phy_read(struct net_device *dev, int mii_id, int reg)
 {
 	struct gem *gp = netdev_priv(dev);
-	return __phy_read(gp, mii_id, reg);
+	return __sungem_phy_read(gp, mii_id, reg);
 }
 
-static inline u16 phy_read(struct gem *gp, int reg)
+static inline u16 sungem_phy_read(struct gem *gp, int reg)
 {
-	return __phy_read(gp, gp->mii_phy_addr, reg);
+	return __sungem_phy_read(gp, gp->mii_phy_addr, reg);
 }
 
-static void __phy_write(struct gem *gp, int phy_addr, int reg, u16 val)
+static void __sungem_phy_write(struct gem *gp, int phy_addr, int reg, u16 val)
 {
 	u32 cmd;
 	int limit = 10000;
@@ -174,15 +174,15 @@
 	}
 }
 
-static inline void _phy_write(struct net_device *dev, int mii_id, int reg, int val)
+static inline void _sungem_phy_write(struct net_device *dev, int mii_id, int reg, int val)
 {
 	struct gem *gp = netdev_priv(dev);
-	__phy_write(gp, mii_id, reg, val & 0xffff);
+	__sungem_phy_write(gp, mii_id, reg, val & 0xffff);
 }
 
-static inline void phy_write(struct gem *gp, int reg, u16 val)
+static inline void sungem_phy_write(struct gem *gp, int reg, u16 val)
 {
-	__phy_write(gp, gp->mii_phy_addr, reg, val);
+	__sungem_phy_write(gp, gp->mii_phy_addr, reg, val);
 }
 
 static inline void gem_enable_ints(struct gem *gp)
@@ -1687,9 +1687,9 @@
 			/* Some PHYs used by apple have problem getting back to us,
 			 * we do an additional reset here
 			 */
-			phy_write(gp, MII_BMCR, BMCR_RESET);
+			sungem_phy_write(gp, MII_BMCR, BMCR_RESET);
 			msleep(20);
-			if (phy_read(gp, MII_BMCR) != 0xffff)
+			if (sungem_phy_read(gp, MII_BMCR) != 0xffff)
 				break;
 			if (i == 2)
 				netdev_warn(gp->dev, "GMAC PHY not responding !\n");
@@ -2012,7 +2012,7 @@
 
 		for (i = 0; i < 32; i++) {
 			gp->mii_phy_addr = i;
-			if (phy_read(gp, MII_BMCR) != 0xffff)
+			if (sungem_phy_read(gp, MII_BMCR) != 0xffff)
 				break;
 		}
 		if (i == 32) {
@@ -2696,13 +2696,13 @@
 		/* Fallthrough... */
 
 	case SIOCGMIIREG:		/* Read MII PHY register. */
-		data->val_out = __phy_read(gp, data->phy_id & 0x1f,
+		data->val_out = __sungem_phy_read(gp, data->phy_id & 0x1f,
 					   data->reg_num & 0x1f);
 		rc = 0;
 		break;
 
 	case SIOCSMIIREG:		/* Write MII PHY register. */
-		__phy_write(gp, data->phy_id & 0x1f, data->reg_num & 0x1f,
+		__sungem_phy_write(gp, data->phy_id & 0x1f, data->reg_num & 0x1f,
 			    data->val_in);
 		rc = 0;
 		break;
@@ -2933,8 +2933,8 @@
 
 	/* Fill up the mii_phy structure (even if we won't use it) */
 	gp->phy_mii.dev = dev;
-	gp->phy_mii.mdio_read = _phy_read;
-	gp->phy_mii.mdio_write = _phy_write;
+	gp->phy_mii.mdio_read = _sungem_phy_read;
+	gp->phy_mii.mdio_write = _sungem_phy_write;
 #ifdef CONFIG_PPC_PMAC
 	gp->phy_mii.platform_data = gp->of_node;
 #endif
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 65de0ca..28437ab 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -205,6 +205,14 @@
 
 	  Currently, only 8-bit registers are supported.
 
+config MDIO_BCM_UNIMAC
+	tristate "Broadcom UniMAC MDIO bus controller"
+	help
+	  This module provides a driver for the Broadcom UniMAC MDIO busses.
+	  This hardware can be found in the Broadcom GENET Ethernet MAC
+	  controllers as well as some Broadcom Ethernet switches such as the
+	  Starfighter 2 switches.
+
 endif # PHYLIB
 
 config MICREL_KS8995MA
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 7dc3d5b..eb3b18b 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -34,3 +34,4 @@
 obj-$(CONFIG_MDIO_SUN4I)	+= mdio-sun4i.o
 obj-$(CONFIG_MDIO_MOXART)	+= mdio-moxart.o
 obj-$(CONFIG_AMD_XGBE_PHY)	+= amd-xgbe-phy.o
+obj-$(CONFIG_MDIO_BCM_UNIMAC)	+= mdio-bcm-unimac.o
diff --git a/drivers/net/phy/bcm7xxx.c b/drivers/net/phy/bcm7xxx.c
index e98c510..09dd6e1 100644
--- a/drivers/net/phy/bcm7xxx.c
+++ b/drivers/net/phy/bcm7xxx.c
@@ -319,44 +319,28 @@
 	return 0;
 }
 
+#define BCM7XXX_28NM_GPHY(_oui, _name)					\
+{									\
+	.phy_id		= (_oui),					\
+	.phy_id_mask	= 0xfffffff0,					\
+	.name		= _name,					\
+	.features	= PHY_GBIT_FEATURES |				\
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,	\
+	.flags		= PHY_IS_INTERNAL,				\
+	.config_init	= bcm7xxx_28nm_afe_config_init,			\
+	.config_aneg	= genphy_config_aneg,				\
+	.read_status	= genphy_read_status,				\
+	.resume		= bcm7xxx_28nm_resume,				\
+	.driver		= { .owner = THIS_MODULE },			\
+}
+
 static struct phy_driver bcm7xxx_driver[] = {
+	BCM7XXX_28NM_GPHY(PHY_ID_BCM7250, "Broadcom BCM7250"),
+	BCM7XXX_28NM_GPHY(PHY_ID_BCM7364, "Broadcom BCM7364"),
+	BCM7XXX_28NM_GPHY(PHY_ID_BCM7366, "Broadcom BCM7366"),
+	BCM7XXX_28NM_GPHY(PHY_ID_BCM7439, "Broadcom BCM7439"),
+	BCM7XXX_28NM_GPHY(PHY_ID_BCM7445, "Broadcom BCM7445"),
 {
-	.phy_id		= PHY_ID_BCM7366,
-	.phy_id_mask	= 0xfffffff0,
-	.name		= "Broadcom BCM7366",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
-	.flags		= PHY_IS_INTERNAL,
-	.config_init	= bcm7xxx_28nm_afe_config_init,
-	.config_aneg	= genphy_config_aneg,
-	.read_status	= genphy_read_status,
-	.resume		= bcm7xxx_28nm_resume,
-	.driver		= { .owner = THIS_MODULE },
-}, {
-	.phy_id		= PHY_ID_BCM7439,
-	.phy_id_mask	= 0xfffffff0,
-	.name		= "Broadcom BCM7439",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
-	.flags		= PHY_IS_INTERNAL,
-	.config_init	= bcm7xxx_28nm_afe_config_init,
-	.config_aneg	= genphy_config_aneg,
-	.read_status	= genphy_read_status,
-	.resume		= bcm7xxx_28nm_resume,
-	.driver		= { .owner = THIS_MODULE },
-}, {
-	.phy_id		= PHY_ID_BCM7445,
-	.phy_id_mask	= 0xfffffff0,
-	.name		= "Broadcom BCM7445",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
-	.flags		= PHY_IS_INTERNAL,
-	.config_init	= bcm7xxx_28nm_config_init,
-	.config_aneg	= genphy_config_aneg,
-	.read_status	= genphy_read_status,
-	.resume		= bcm7xxx_28nm_afe_config_init,
-	.driver		= { .owner = THIS_MODULE },
-}, {
 	.phy_id		= PHY_BCM_OUI_4,
 	.phy_id_mask	= 0xffff0000,
 	.name		= "Broadcom BCM7XXX 40nm",
@@ -385,6 +369,8 @@
 } };
 
 static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = {
+	{ PHY_ID_BCM7250, 0xfffffff0, },
+	{ PHY_ID_BCM7364, 0xfffffff0, },
 	{ PHY_ID_BCM7366, 0xfffffff0, },
 	{ PHY_ID_BCM7439, 0xfffffff0, },
 	{ PHY_ID_BCM7445, 0xfffffff0, },
diff --git a/drivers/net/phy/mdio-bcm-unimac.c b/drivers/net/phy/mdio-bcm-unimac.c
new file mode 100644
index 0000000..e6b08ce
--- /dev/null
+++ b/drivers/net/phy/mdio-bcm-unimac.c
@@ -0,0 +1,212 @@
+/*
+ * Broadcom UniMAC MDIO bus controller driver
+ *
+ * Copyright (C) 2014, Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/of_mdio.h>
+
+#define MDIO_CMD		0x00
+#define  MDIO_START_BUSY	(1 << 29)
+#define  MDIO_READ_FAIL		(1 << 28)
+#define  MDIO_RD		(2 << 26)
+#define  MDIO_WR		(1 << 26)
+#define  MDIO_PMD_SHIFT		21
+#define  MDIO_PMD_MASK		0x1F
+#define  MDIO_REG_SHIFT		16
+#define  MDIO_REG_MASK		0x1F
+
+#define MDIO_CFG		0x04
+#define  MDIO_C22		(1 << 0)
+#define  MDIO_C45		0
+#define  MDIO_CLK_DIV_SHIFT	4
+#define  MDIO_CLK_DIV_MASK	0x3F
+#define  MDIO_SUPP_PREAMBLE	(1 << 12)
+
+struct unimac_mdio_priv {
+	struct mii_bus		*mii_bus;
+	void __iomem		*base;
+};
+
+static inline void unimac_mdio_start(struct unimac_mdio_priv *priv)
+{
+	u32 reg;
+
+	reg = __raw_readl(priv->base + MDIO_CMD);
+	reg |= MDIO_START_BUSY;
+	__raw_writel(reg, priv->base + MDIO_CMD);
+}
+
+static inline unsigned int unimac_mdio_busy(struct unimac_mdio_priv *priv)
+{
+	return __raw_readl(priv->base + MDIO_CMD) & MDIO_START_BUSY;
+}
+
+static int unimac_mdio_read(struct mii_bus *bus, int phy_id, int reg)
+{
+	struct unimac_mdio_priv *priv = bus->priv;
+	unsigned int timeout = 1000;
+	u32 cmd;
+
+	/* Prepare the read operation */
+	cmd = MDIO_RD | (phy_id << MDIO_PMD_SHIFT) | (reg << MDIO_REG_SHIFT);
+	__raw_writel(cmd, priv->base + MDIO_CMD);
+
+	/* Start MDIO transaction */
+	unimac_mdio_start(priv);
+
+	do {
+		if (!unimac_mdio_busy(priv))
+			break;
+
+		usleep_range(1000, 2000);
+	} while (timeout--);
+
+	if (!timeout)
+		return -ETIMEDOUT;
+
+	cmd = __raw_readl(priv->base + MDIO_CMD);
+	if (cmd & MDIO_READ_FAIL)
+		return -EIO;
+
+	return cmd & 0xffff;
+}
+
+static int unimac_mdio_write(struct mii_bus *bus, int phy_id,
+			     int reg, u16 val)
+{
+	struct unimac_mdio_priv *priv = bus->priv;
+	unsigned int timeout = 1000;
+	u32 cmd;
+
+	/* Prepare the write operation */
+	cmd = MDIO_WR | (phy_id << MDIO_PMD_SHIFT) |
+		(reg << MDIO_REG_SHIFT) | (0xffff & val);
+	__raw_writel(cmd, priv->base + MDIO_CMD);
+
+	unimac_mdio_start(priv);
+
+	do {
+		if (!unimac_mdio_busy(priv))
+			break;
+
+		usleep_range(1000, 2000);
+	} while (timeout--);
+
+	if (!timeout)
+		return -ETIMEDOUT;
+
+	return 0;
+}
+
+static int unimac_mdio_probe(struct platform_device *pdev)
+{
+	struct unimac_mdio_priv *priv;
+	struct device_node *np;
+	struct mii_bus *bus;
+	struct resource *r;
+	int ret;
+
+	np = pdev->dev.of_node;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+	/* Just ioremap, as this MDIO block is usually integrated into an
+	 * Ethernet MAC controller register range
+	 */
+	priv->base = devm_ioremap(&pdev->dev, r->start, resource_size(r));
+	if (!priv->base) {
+		dev_err(&pdev->dev, "failed to remap register\n");
+		return -ENOMEM;
+	}
+
+	priv->mii_bus = mdiobus_alloc();
+	if (!priv->mii_bus)
+		return -ENOMEM;
+
+	bus = priv->mii_bus;
+	bus->priv = priv;
+	bus->name = "unimac MII bus";
+	bus->parent = &pdev->dev;
+	bus->read = unimac_mdio_read;
+	bus->write = unimac_mdio_write;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s", pdev->name);
+
+	bus->irq = kcalloc(PHY_MAX_ADDR, sizeof(int), GFP_KERNEL);
+	if (!bus->irq) {
+		ret = -ENOMEM;
+		goto out_mdio_free;
+	}
+
+	ret = of_mdiobus_register(bus, np);
+	if (ret) {
+		dev_err(&pdev->dev, "MDIO bus registration failed\n");
+		goto out_mdio_irq;
+	}
+
+	platform_set_drvdata(pdev, priv);
+
+	dev_info(&pdev->dev, "Broadcom UniMAC MDIO bus at 0x%p\n", priv->base);
+
+	return 0;
+
+out_mdio_irq:
+	kfree(bus->irq);
+out_mdio_free:
+	mdiobus_free(bus);
+	return ret;
+}
+
+static int unimac_mdio_remove(struct platform_device *pdev)
+{
+	struct unimac_mdio_priv *priv = platform_get_drvdata(pdev);
+
+	mdiobus_unregister(priv->mii_bus);
+	kfree(priv->mii_bus->irq);
+	mdiobus_free(priv->mii_bus);
+
+	return 0;
+}
+
+static struct of_device_id unimac_mdio_ids[] = {
+	{ .compatible = "brcm,genet-mdio-v4", },
+	{ .compatible = "brcm,genet-mdio-v3", },
+	{ .compatible = "brcm,genet-mdio-v2", },
+	{ .compatible = "brcm,genet-mdio-v1", },
+	{ .compatible = "brcm,unimac-mdio", },
+};
+
+static struct platform_driver unimac_mdio_driver = {
+	.driver = {
+		.name = "unimac-mdio",
+		.owner = THIS_MODULE,
+		.of_match_table = unimac_mdio_ids,
+	},
+	.probe	= unimac_mdio_probe,
+	.remove	= unimac_mdio_remove,
+};
+module_platform_driver(unimac_mdio_driver);
+
+MODULE_AUTHOR("Broadcom Corporation");
+MODULE_DESCRIPTION("Broadcom UniMAC MDIO bus controller");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:unimac-mdio");
diff --git a/drivers/net/sungem_phy.c b/drivers/net/sungem_phy.c
index ae7cd7f..92578d72 100644
--- a/drivers/net/sungem_phy.c
+++ b/drivers/net/sungem_phy.c
@@ -47,22 +47,22 @@
 	{ 1, 0, 1 },	/* 1000BT */
 };
 
-static inline int __phy_read(struct mii_phy* phy, int id, int reg)
+static inline int __sungem_phy_read(struct mii_phy* phy, int id, int reg)
 {
 	return phy->mdio_read(phy->dev, id, reg);
 }
 
-static inline void __phy_write(struct mii_phy* phy, int id, int reg, int val)
+static inline void __sungem_phy_write(struct mii_phy* phy, int id, int reg, int val)
 {
 	phy->mdio_write(phy->dev, id, reg, val);
 }
 
-static inline int phy_read(struct mii_phy* phy, int reg)
+static inline int sungem_phy_read(struct mii_phy* phy, int reg)
 {
 	return phy->mdio_read(phy->dev, phy->mii_id, reg);
 }
 
-static inline void phy_write(struct mii_phy* phy, int reg, int val)
+static inline void sungem_phy_write(struct mii_phy* phy, int reg, int val)
 {
 	phy->mdio_write(phy->dev, phy->mii_id, reg, val);
 }
@@ -72,21 +72,21 @@
 	u16 val;
 	int limit = 10000;
 
-	val = __phy_read(phy, phy_id, MII_BMCR);
+	val = __sungem_phy_read(phy, phy_id, MII_BMCR);
 	val &= ~(BMCR_ISOLATE | BMCR_PDOWN);
 	val |= BMCR_RESET;
-	__phy_write(phy, phy_id, MII_BMCR, val);
+	__sungem_phy_write(phy, phy_id, MII_BMCR, val);
 
 	udelay(100);
 
 	while (--limit) {
-		val = __phy_read(phy, phy_id, MII_BMCR);
+		val = __sungem_phy_read(phy, phy_id, MII_BMCR);
 		if ((val & BMCR_RESET) == 0)
 			break;
 		udelay(10);
 	}
 	if ((val & BMCR_ISOLATE) && limit > 0)
-		__phy_write(phy, phy_id, MII_BMCR, val & ~BMCR_ISOLATE);
+		__sungem_phy_write(phy, phy_id, MII_BMCR, val & ~BMCR_ISOLATE);
 
 	return limit <= 0;
 }
@@ -95,19 +95,19 @@
 {
 	u16 data;
 
-	data = phy_read(phy, MII_BCM5201_MULTIPHY);
+	data = sungem_phy_read(phy, MII_BCM5201_MULTIPHY);
 	data &= ~MII_BCM5201_MULTIPHY_SUPERISOLATE;
-	phy_write(phy, MII_BCM5201_MULTIPHY, data);
+	sungem_phy_write(phy, MII_BCM5201_MULTIPHY, data);
 
-	phy_write(phy, MII_BCM5201_INTERRUPT, 0);
+	sungem_phy_write(phy, MII_BCM5201_INTERRUPT, 0);
 
 	return 0;
 }
 
 static int bcm5201_suspend(struct mii_phy* phy)
 {
-	phy_write(phy, MII_BCM5201_INTERRUPT, 0);
-	phy_write(phy, MII_BCM5201_MULTIPHY, MII_BCM5201_MULTIPHY_SUPERISOLATE);
+	sungem_phy_write(phy, MII_BCM5201_INTERRUPT, 0);
+	sungem_phy_write(phy, MII_BCM5201_MULTIPHY, MII_BCM5201_MULTIPHY_SUPERISOLATE);
 
 	return 0;
 }
@@ -116,20 +116,20 @@
 {
 	u16 data;
 
-	data = phy_read(phy, MII_BCM5221_TEST);
-	phy_write(phy, MII_BCM5221_TEST,
+	data = sungem_phy_read(phy, MII_BCM5221_TEST);
+	sungem_phy_write(phy, MII_BCM5221_TEST,
 		data | MII_BCM5221_TEST_ENABLE_SHADOWS);
 
-	data = phy_read(phy, MII_BCM5221_SHDOW_AUX_STAT2);
-	phy_write(phy, MII_BCM5221_SHDOW_AUX_STAT2,
+	data = sungem_phy_read(phy, MII_BCM5221_SHDOW_AUX_STAT2);
+	sungem_phy_write(phy, MII_BCM5221_SHDOW_AUX_STAT2,
 		data | MII_BCM5221_SHDOW_AUX_STAT2_APD);
 
-	data = phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
-	phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
+	data = sungem_phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
+	sungem_phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
 		data | MII_BCM5221_SHDOW_AUX_MODE4_CLKLOPWR);
 
-	data = phy_read(phy, MII_BCM5221_TEST);
-	phy_write(phy, MII_BCM5221_TEST,
+	data = sungem_phy_read(phy, MII_BCM5221_TEST);
+	sungem_phy_write(phy, MII_BCM5221_TEST,
 		data & ~MII_BCM5221_TEST_ENABLE_SHADOWS);
 
 	return 0;
@@ -139,12 +139,12 @@
 {
 	u16 data;
 
-	data = phy_read(phy, MII_BCM5221_TEST);
-	phy_write(phy, MII_BCM5221_TEST,
+	data = sungem_phy_read(phy, MII_BCM5221_TEST);
+	sungem_phy_write(phy, MII_BCM5221_TEST,
 		data | MII_BCM5221_TEST_ENABLE_SHADOWS);
 
-	data = phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
-	phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
+	data = sungem_phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
+	sungem_phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
 		  data | MII_BCM5221_SHDOW_AUX_MODE4_IDDQMODE);
 
 	return 0;
@@ -154,20 +154,20 @@
 {
 	u16 data;
 
-	data = phy_read(phy, MII_BCM5221_TEST);
-	phy_write(phy, MII_BCM5221_TEST,
+	data = sungem_phy_read(phy, MII_BCM5221_TEST);
+	sungem_phy_write(phy, MII_BCM5221_TEST,
 		data | MII_BCM5221_TEST_ENABLE_SHADOWS);
 
-	data = phy_read(phy, MII_BCM5221_SHDOW_AUX_STAT2);
-	phy_write(phy, MII_BCM5221_SHDOW_AUX_STAT2,
+	data = sungem_phy_read(phy, MII_BCM5221_SHDOW_AUX_STAT2);
+	sungem_phy_write(phy, MII_BCM5221_SHDOW_AUX_STAT2,
 		data | MII_BCM5221_SHDOW_AUX_STAT2_APD);
 
-	data = phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
-	phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
+	data = sungem_phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
+	sungem_phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
 		data & ~MII_BCM5241_SHDOW_AUX_MODE4_STANDBYPWR);
 
-	data = phy_read(phy, MII_BCM5221_TEST);
-	phy_write(phy, MII_BCM5221_TEST,
+	data = sungem_phy_read(phy, MII_BCM5221_TEST);
+	sungem_phy_write(phy, MII_BCM5221_TEST,
 		data & ~MII_BCM5221_TEST_ENABLE_SHADOWS);
 
 	return 0;
@@ -177,12 +177,12 @@
 {
 	u16 data;
 
-	data = phy_read(phy, MII_BCM5221_TEST);
-	phy_write(phy, MII_BCM5221_TEST,
+	data = sungem_phy_read(phy, MII_BCM5221_TEST);
+	sungem_phy_write(phy, MII_BCM5221_TEST,
 		data | MII_BCM5221_TEST_ENABLE_SHADOWS);
 
-	data = phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
-	phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
+	data = sungem_phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
+	sungem_phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
 		  data | MII_BCM5241_SHDOW_AUX_MODE4_STANDBYPWR);
 
 	return 0;
@@ -193,26 +193,26 @@
 	u16 data;
 
 	/* Configure for gigabit full duplex */
-	data = phy_read(phy, MII_BCM5400_AUXCONTROL);
+	data = sungem_phy_read(phy, MII_BCM5400_AUXCONTROL);
 	data |= MII_BCM5400_AUXCONTROL_PWR10BASET;
-	phy_write(phy, MII_BCM5400_AUXCONTROL, data);
+	sungem_phy_write(phy, MII_BCM5400_AUXCONTROL, data);
 
-	data = phy_read(phy, MII_BCM5400_GB_CONTROL);
+	data = sungem_phy_read(phy, MII_BCM5400_GB_CONTROL);
 	data |= MII_BCM5400_GB_CONTROL_FULLDUPLEXCAP;
-	phy_write(phy, MII_BCM5400_GB_CONTROL, data);
+	sungem_phy_write(phy, MII_BCM5400_GB_CONTROL, data);
 
 	udelay(100);
 
 	/* Reset and configure cascaded 10/100 PHY */
 	(void)reset_one_mii_phy(phy, 0x1f);
 
-	data = __phy_read(phy, 0x1f, MII_BCM5201_MULTIPHY);
+	data = __sungem_phy_read(phy, 0x1f, MII_BCM5201_MULTIPHY);
 	data |= MII_BCM5201_MULTIPHY_SERIALMODE;
-	__phy_write(phy, 0x1f, MII_BCM5201_MULTIPHY, data);
+	__sungem_phy_write(phy, 0x1f, MII_BCM5201_MULTIPHY, data);
 
-	data = phy_read(phy, MII_BCM5400_AUXCONTROL);
+	data = sungem_phy_read(phy, MII_BCM5400_AUXCONTROL);
 	data &= ~MII_BCM5400_AUXCONTROL_PWR10BASET;
-	phy_write(phy, MII_BCM5400_AUXCONTROL, data);
+	sungem_phy_write(phy, MII_BCM5400_AUXCONTROL, data);
 
 	return 0;
 }
@@ -220,7 +220,7 @@
 static int bcm5400_suspend(struct mii_phy* phy)
 {
 #if 0 /* Commented out in Darwin... someone has those dawn docs ? */
-	phy_write(phy, MII_BMCR, BMCR_PDOWN);
+	sungem_phy_write(phy, MII_BMCR, BMCR_PDOWN);
 #endif
 	return 0;
 }
@@ -230,7 +230,7 @@
 	u16 data;
 	int rev;
 
-	rev = phy_read(phy, MII_PHYSID2) & 0x000f;
+	rev = sungem_phy_read(phy, MII_PHYSID2) & 0x000f;
 	if (rev == 0 || rev == 3) {
 		/* Some revisions of 5401 appear to need this
 		 * initialisation sequence to disable, according
@@ -243,32 +243,32 @@
 		 * Note: This should (and does) match tg3_init_5401phy_dsp
 		 *       in the tg3.c driver. -DaveM
 		 */
-		phy_write(phy, 0x18, 0x0c20);
-		phy_write(phy, 0x17, 0x0012);
-		phy_write(phy, 0x15, 0x1804);
-		phy_write(phy, 0x17, 0x0013);
-		phy_write(phy, 0x15, 0x1204);
-		phy_write(phy, 0x17, 0x8006);
-		phy_write(phy, 0x15, 0x0132);
-		phy_write(phy, 0x17, 0x8006);
-		phy_write(phy, 0x15, 0x0232);
-		phy_write(phy, 0x17, 0x201f);
-		phy_write(phy, 0x15, 0x0a20);
+		sungem_phy_write(phy, 0x18, 0x0c20);
+		sungem_phy_write(phy, 0x17, 0x0012);
+		sungem_phy_write(phy, 0x15, 0x1804);
+		sungem_phy_write(phy, 0x17, 0x0013);
+		sungem_phy_write(phy, 0x15, 0x1204);
+		sungem_phy_write(phy, 0x17, 0x8006);
+		sungem_phy_write(phy, 0x15, 0x0132);
+		sungem_phy_write(phy, 0x17, 0x8006);
+		sungem_phy_write(phy, 0x15, 0x0232);
+		sungem_phy_write(phy, 0x17, 0x201f);
+		sungem_phy_write(phy, 0x15, 0x0a20);
 	}
 
 	/* Configure for gigabit full duplex */
-	data = phy_read(phy, MII_BCM5400_GB_CONTROL);
+	data = sungem_phy_read(phy, MII_BCM5400_GB_CONTROL);
 	data |= MII_BCM5400_GB_CONTROL_FULLDUPLEXCAP;
-	phy_write(phy, MII_BCM5400_GB_CONTROL, data);
+	sungem_phy_write(phy, MII_BCM5400_GB_CONTROL, data);
 
 	udelay(10);
 
 	/* Reset and configure cascaded 10/100 PHY */
 	(void)reset_one_mii_phy(phy, 0x1f);
 
-	data = __phy_read(phy, 0x1f, MII_BCM5201_MULTIPHY);
+	data = __sungem_phy_read(phy, 0x1f, MII_BCM5201_MULTIPHY);
 	data |= MII_BCM5201_MULTIPHY_SERIALMODE;
-	__phy_write(phy, 0x1f, MII_BCM5201_MULTIPHY, data);
+	__sungem_phy_write(phy, 0x1f, MII_BCM5201_MULTIPHY, data);
 
 	return 0;
 }
@@ -276,7 +276,7 @@
 static int bcm5401_suspend(struct mii_phy* phy)
 {
 #if 0 /* Commented out in Darwin... someone has those dawn docs ? */
-	phy_write(phy, MII_BMCR, BMCR_PDOWN);
+	sungem_phy_write(phy, MII_BMCR, BMCR_PDOWN);
 #endif
 	return 0;
 }
@@ -288,19 +288,19 @@
 	/* Here's some more Apple black magic to setup
 	 * some voltage stuffs.
 	 */
-	phy_write(phy, 0x1c, 0x8c23);
-	phy_write(phy, 0x1c, 0x8ca3);
-	phy_write(phy, 0x1c, 0x8c23);
+	sungem_phy_write(phy, 0x1c, 0x8c23);
+	sungem_phy_write(phy, 0x1c, 0x8ca3);
+	sungem_phy_write(phy, 0x1c, 0x8c23);
 
 	/* Here, Apple seems to want to reset it, do
 	 * it as well
 	 */
-	phy_write(phy, MII_BMCR, BMCR_RESET);
-	phy_write(phy, MII_BMCR, 0x1340);
+	sungem_phy_write(phy, MII_BMCR, BMCR_RESET);
+	sungem_phy_write(phy, MII_BMCR, 0x1340);
 
-	data = phy_read(phy, MII_BCM5400_GB_CONTROL);
+	data = sungem_phy_read(phy, MII_BCM5400_GB_CONTROL);
 	data |= MII_BCM5400_GB_CONTROL_FULLDUPLEXCAP;
-	phy_write(phy, MII_BCM5400_GB_CONTROL, data);
+	sungem_phy_write(phy, MII_BCM5400_GB_CONTROL, data);
 
 	udelay(10);
 
@@ -321,7 +321,7 @@
 	phy->advertising = advertise;
 
 	/* Setup standard advertise */
-	adv = phy_read(phy, MII_ADVERTISE);
+	adv = sungem_phy_read(phy, MII_ADVERTISE);
 	adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
 	if (advertise & ADVERTISED_10baseT_Half)
 		adv |= ADVERTISE_10HALF;
@@ -331,12 +331,12 @@
 		adv |= ADVERTISE_100HALF;
 	if (advertise & ADVERTISED_100baseT_Full)
 		adv |= ADVERTISE_100FULL;
-	phy_write(phy, MII_ADVERTISE, adv);
+	sungem_phy_write(phy, MII_ADVERTISE, adv);
 
 	/* Start/Restart aneg */
-	ctl = phy_read(phy, MII_BMCR);
+	ctl = sungem_phy_read(phy, MII_BMCR);
 	ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
-	phy_write(phy, MII_BMCR, ctl);
+	sungem_phy_write(phy, MII_BMCR, ctl);
 
 	return 0;
 }
@@ -350,11 +350,11 @@
 	phy->duplex = fd;
 	phy->pause = 0;
 
-	ctl = phy_read(phy, MII_BMCR);
+	ctl = sungem_phy_read(phy, MII_BMCR);
 	ctl &= ~(BMCR_FULLDPLX|BMCR_SPEED100|BMCR_ANENABLE);
 
 	/* First reset the PHY */
-	phy_write(phy, MII_BMCR, ctl | BMCR_RESET);
+	sungem_phy_write(phy, MII_BMCR, ctl | BMCR_RESET);
 
 	/* Select speed & duplex */
 	switch(speed) {
@@ -369,7 +369,7 @@
 	}
 	if (fd == DUPLEX_FULL)
 		ctl |= BMCR_FULLDPLX;
-	phy_write(phy, MII_BMCR, ctl);
+	sungem_phy_write(phy, MII_BMCR, ctl);
 
 	return 0;
 }
@@ -378,8 +378,8 @@
 {
 	u16 status;
 
-	(void)phy_read(phy, MII_BMSR);
-	status = phy_read(phy, MII_BMSR);
+	(void)sungem_phy_read(phy, MII_BMSR);
+	status = sungem_phy_read(phy, MII_BMSR);
 	if ((status & BMSR_LSTATUS) == 0)
 		return 0;
 	if (phy->autoneg && !(status & BMSR_ANEGCOMPLETE))
@@ -392,7 +392,7 @@
 	u16 lpa;
 
 	if (phy->autoneg) {
-		lpa = phy_read(phy, MII_LPA);
+		lpa = sungem_phy_read(phy, MII_LPA);
 
 		if (lpa & (LPA_10FULL | LPA_100FULL))
 			phy->duplex = DUPLEX_FULL;
@@ -413,7 +413,7 @@
 
 static int generic_suspend(struct mii_phy* phy)
 {
-	phy_write(phy, MII_BMCR, BMCR_PDOWN);
+	sungem_phy_write(phy, MII_BMCR, BMCR_PDOWN);
 
 	return 0;
 }
@@ -423,27 +423,27 @@
 	u16 data;
 	unsigned int id;
 
-	id = (phy_read(phy, MII_PHYSID1) << 16 | phy_read(phy, MII_PHYSID2));
+	id = (sungem_phy_read(phy, MII_PHYSID1) << 16 | sungem_phy_read(phy, MII_PHYSID2));
 
 	/* Revision 0 of 5421 needs some fixups */
 	if (id == 0x002060e0) {
 		/* This is borrowed from MacOS
 		 */
-		phy_write(phy, 0x18, 0x1007);
-		data = phy_read(phy, 0x18);
-		phy_write(phy, 0x18, data | 0x0400);
-		phy_write(phy, 0x18, 0x0007);
-		data = phy_read(phy, 0x18);
-		phy_write(phy, 0x18, data | 0x0800);
-		phy_write(phy, 0x17, 0x000a);
-		data = phy_read(phy, 0x15);
-		phy_write(phy, 0x15, data | 0x0200);
+		sungem_phy_write(phy, 0x18, 0x1007);
+		data = sungem_phy_read(phy, 0x18);
+		sungem_phy_write(phy, 0x18, data | 0x0400);
+		sungem_phy_write(phy, 0x18, 0x0007);
+		data = sungem_phy_read(phy, 0x18);
+		sungem_phy_write(phy, 0x18, data | 0x0800);
+		sungem_phy_write(phy, 0x17, 0x000a);
+		data = sungem_phy_read(phy, 0x15);
+		sungem_phy_write(phy, 0x15, data | 0x0200);
 	}
 
 	/* Pick up some init code from OF for K2 version */
 	if ((id & 0xfffffff0) == 0x002062e0) {
-		phy_write(phy, 4, 0x01e1);
-		phy_write(phy, 9, 0x0300);
+		sungem_phy_write(phy, 4, 0x01e1);
+		sungem_phy_write(phy, 9, 0x0300);
 	}
 
 	/* Check if we can enable automatic low power */
@@ -455,9 +455,9 @@
 			can_low_power = 0;
 		if (can_low_power) {
 			/* Enable automatic low-power */
-			phy_write(phy, 0x1c, 0x9002);
-			phy_write(phy, 0x1c, 0xa821);
-			phy_write(phy, 0x1c, 0x941d);
+			sungem_phy_write(phy, 0x1c, 0x9002);
+			sungem_phy_write(phy, 0x1c, 0xa821);
+			sungem_phy_write(phy, 0x1c, 0x941d);
 		}
 	}
 #endif /* CONFIG_PPC_PMAC */
@@ -476,7 +476,7 @@
 	phy->advertising = advertise;
 
 	/* Setup standard advertise */
-	adv = phy_read(phy, MII_ADVERTISE);
+	adv = sungem_phy_read(phy, MII_ADVERTISE);
 	adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
 	if (advertise & ADVERTISED_10baseT_Half)
 		adv |= ADVERTISE_10HALF;
@@ -490,21 +490,21 @@
 		adv |= ADVERTISE_PAUSE_CAP;
 	if (advertise & ADVERTISED_Asym_Pause)
 		adv |= ADVERTISE_PAUSE_ASYM;
-	phy_write(phy, MII_ADVERTISE, adv);
+	sungem_phy_write(phy, MII_ADVERTISE, adv);
 
 	/* Setup 1000BT advertise */
-	adv = phy_read(phy, MII_1000BASETCONTROL);
+	adv = sungem_phy_read(phy, MII_1000BASETCONTROL);
 	adv &= ~(MII_1000BASETCONTROL_FULLDUPLEXCAP|MII_1000BASETCONTROL_HALFDUPLEXCAP);
 	if (advertise & SUPPORTED_1000baseT_Half)
 		adv |= MII_1000BASETCONTROL_HALFDUPLEXCAP;
 	if (advertise & SUPPORTED_1000baseT_Full)
 		adv |= MII_1000BASETCONTROL_FULLDUPLEXCAP;
-	phy_write(phy, MII_1000BASETCONTROL, adv);
+	sungem_phy_write(phy, MII_1000BASETCONTROL, adv);
 
 	/* Start/Restart aneg */
-	ctl = phy_read(phy, MII_BMCR);
+	ctl = sungem_phy_read(phy, MII_BMCR);
 	ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
-	phy_write(phy, MII_BMCR, ctl);
+	sungem_phy_write(phy, MII_BMCR, ctl);
 
 	return 0;
 }
@@ -518,11 +518,11 @@
 	phy->duplex = fd;
 	phy->pause = 0;
 
-	ctl = phy_read(phy, MII_BMCR);
+	ctl = sungem_phy_read(phy, MII_BMCR);
 	ctl &= ~(BMCR_FULLDPLX|BMCR_SPEED100|BMCR_SPD2|BMCR_ANENABLE);
 
 	/* First reset the PHY */
-	phy_write(phy, MII_BMCR, ctl | BMCR_RESET);
+	sungem_phy_write(phy, MII_BMCR, ctl | BMCR_RESET);
 
 	/* Select speed & duplex */
 	switch(speed) {
@@ -539,7 +539,7 @@
 
 	// XXX Should we set the sungem to GII now on 1000BT ?
 
-	phy_write(phy, MII_BMCR, ctl);
+	sungem_phy_write(phy, MII_BMCR, ctl);
 
 	return 0;
 }
@@ -550,7 +550,7 @@
 	u16 val;
 
 	if (phy->autoneg) {
-	    	val = phy_read(phy, MII_BCM5400_AUXSTATUS);
+	    	val = sungem_phy_read(phy, MII_BCM5400_AUXSTATUS);
 		link_mode = ((val & MII_BCM5400_AUXSTATUS_LINKMODE_MASK) >>
 			     MII_BCM5400_AUXSTATUS_LINKMODE_SHIFT);
 		phy->duplex = phy_BCM5400_link_table[link_mode][0] ?
@@ -559,7 +559,7 @@
 				SPEED_1000 :
 				(phy_BCM5400_link_table[link_mode][1] ?
 				 SPEED_100 : SPEED_10);
-		val = phy_read(phy, MII_LPA);
+		val = sungem_phy_read(phy, MII_LPA);
 		phy->pause = (phy->duplex == DUPLEX_FULL) &&
 			((val & LPA_PAUSE) != 0);
 	}
@@ -575,19 +575,19 @@
 	u16 rev;
 
 	/* magic init sequence for rev 0 */
-	rev = phy_read(phy, MII_PHYSID2) & 0x000f;
+	rev = sungem_phy_read(phy, MII_PHYSID2) & 0x000f;
 	if (rev == 0) {
-		phy_write(phy, 0x1d, 0x000a);
-		phy_write(phy, 0x1e, 0x0821);
+		sungem_phy_write(phy, 0x1d, 0x000a);
+		sungem_phy_write(phy, 0x1e, 0x0821);
 
-		phy_write(phy, 0x1d, 0x0006);
-		phy_write(phy, 0x1e, 0x8600);
+		sungem_phy_write(phy, 0x1d, 0x0006);
+		sungem_phy_write(phy, 0x1e, 0x8600);
 
-		phy_write(phy, 0x1d, 0x000b);
-		phy_write(phy, 0x1e, 0x0100);
+		sungem_phy_write(phy, 0x1d, 0x000b);
+		sungem_phy_write(phy, 0x1e, 0x0100);
 
-		phy_write(phy, 0x1d, 0x0004);
-		phy_write(phy, 0x1e, 0x4850);
+		sungem_phy_write(phy, 0x1d, 0x0004);
+		sungem_phy_write(phy, 0x1e, 0x4850);
 	}
 	return 0;
 }
@@ -600,8 +600,8 @@
 	int mode;
 
 	/* find out in what mode we are */
-	phy_write(phy, MII_NCONFIG, 0x1000);
-	phy_reg = phy_read(phy, MII_NCONFIG);
+	sungem_phy_write(phy, MII_NCONFIG, 0x1000);
+	phy_reg = sungem_phy_read(phy, MII_NCONFIG);
 
 	mode = (phy_reg & BCM5421_MODE_MASK) >> 5;
 
@@ -609,8 +609,8 @@
 		return genmii_poll_link(phy);
 
 	/* try to find out whether we have a link */
-	phy_write(phy, MII_NCONFIG, 0x2000);
-	phy_reg = phy_read(phy, MII_NCONFIG);
+	sungem_phy_write(phy, MII_NCONFIG, 0x2000);
+	phy_reg = sungem_phy_read(phy, MII_NCONFIG);
 
 	if (phy_reg & 0x0020)
 		return 0;
@@ -624,8 +624,8 @@
 	int mode;
 
 	/* find out in what mode we are */
-	phy_write(phy, MII_NCONFIG, 0x1000);
-	phy_reg = phy_read(phy, MII_NCONFIG);
+	sungem_phy_write(phy, MII_NCONFIG, 0x1000);
+	phy_reg = sungem_phy_read(phy, MII_NCONFIG);
 
 	mode = (phy_reg & BCM5421_MODE_MASK ) >> 5;
 
@@ -635,8 +635,8 @@
 	phy->speed = SPEED_1000;
 
 	/* find out whether we are running half- or full duplex */
-	phy_write(phy, MII_NCONFIG, 0x2000);
-	phy_reg = phy_read(phy, MII_NCONFIG);
+	sungem_phy_write(phy, MII_NCONFIG, 0x2000);
+	phy_reg = sungem_phy_read(phy, MII_NCONFIG);
 
 	if ( (phy_reg & 0x0080) >> 7)
 		phy->duplex |=  DUPLEX_HALF;
@@ -649,14 +649,14 @@
 static int bcm5421_enable_fiber(struct mii_phy* phy, int autoneg)
 {
 	/* enable fiber mode */
-	phy_write(phy, MII_NCONFIG, 0x9020);
+	sungem_phy_write(phy, MII_NCONFIG, 0x9020);
 	/* LEDs active in both modes, autosense prio = fiber */
-	phy_write(phy, MII_NCONFIG, 0x945f);
+	sungem_phy_write(phy, MII_NCONFIG, 0x945f);
 
 	if (!autoneg) {
 		/* switch off fibre autoneg */
-		phy_write(phy, MII_NCONFIG, 0xfc01);
-		phy_write(phy, 0x0b, 0x0004);
+		sungem_phy_write(phy, MII_NCONFIG, 0xfc01);
+		sungem_phy_write(phy, 0x0b, 0x0004);
 	}
 
 	phy->autoneg = autoneg;
@@ -673,8 +673,8 @@
 	int mode;
 
 	/* find out in what mode we are */
-	phy_write(phy, MII_NCONFIG, 0x7c00);
-	phy_reg = phy_read(phy, MII_NCONFIG);
+	sungem_phy_write(phy, MII_NCONFIG, 0x7c00);
+	phy_reg = sungem_phy_read(phy, MII_NCONFIG);
 
 	mode = (phy_reg & BCM5461_MODE_MASK ) >> 1;
 
@@ -682,8 +682,8 @@
 		return genmii_poll_link(phy);
 
 	/* find out whether we have a link */
-	phy_write(phy, MII_NCONFIG, 0x7000);
-	phy_reg = phy_read(phy, MII_NCONFIG);
+	sungem_phy_write(phy, MII_NCONFIG, 0x7000);
+	phy_reg = sungem_phy_read(phy, MII_NCONFIG);
 
 	if (phy_reg & BCM5461_FIBER_LINK)
 		return 1;
@@ -699,8 +699,8 @@
 	int mode;
 
 	/* find out in what mode we are */
-	phy_write(phy, MII_NCONFIG, 0x7c00);
-	phy_reg = phy_read(phy, MII_NCONFIG);
+	sungem_phy_write(phy, MII_NCONFIG, 0x7c00);
+	phy_reg = sungem_phy_read(phy, MII_NCONFIG);
 
 	mode = (phy_reg & BCM5461_MODE_MASK ) >> 1;
 
@@ -711,8 +711,8 @@
 	phy->speed = SPEED_1000;
 
 	/* find out whether we are running half- or full duplex */
-	phy_write(phy, MII_NCONFIG, 0x7000);
-	phy_reg = phy_read(phy, MII_NCONFIG);
+	sungem_phy_write(phy, MII_NCONFIG, 0x7000);
+	phy_reg = sungem_phy_read(phy, MII_NCONFIG);
 
 	if (phy_reg & BCM5461_FIBER_DUPLEX)
 		phy->duplex |=  DUPLEX_FULL;
@@ -725,15 +725,15 @@
 static int bcm5461_enable_fiber(struct mii_phy* phy, int autoneg)
 {
 	/* select fiber mode, enable 1000 base-X registers */
-	phy_write(phy, MII_NCONFIG, 0xfc0b);
+	sungem_phy_write(phy, MII_NCONFIG, 0xfc0b);
 
 	if (autoneg) {
 		/* enable fiber with no autonegotiation */
-		phy_write(phy, MII_ADVERTISE, 0x01e0);
-		phy_write(phy, MII_BMCR, 0x1140);
+		sungem_phy_write(phy, MII_ADVERTISE, 0x01e0);
+		sungem_phy_write(phy, MII_BMCR, 0x1140);
 	} else {
 		/* enable fiber with autonegotiation */
-		phy_write(phy, MII_BMCR, 0x0140);
+		sungem_phy_write(phy, MII_BMCR, 0x0140);
 	}
 
 	phy->autoneg = autoneg;
@@ -752,7 +752,7 @@
 	phy->advertising = advertise;
 
 	/* Setup standard advertise */
-	adv = phy_read(phy, MII_ADVERTISE);
+	adv = sungem_phy_read(phy, MII_ADVERTISE);
 	adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
 	if (advertise & ADVERTISED_10baseT_Half)
 		adv |= ADVERTISE_10HALF;
@@ -766,7 +766,7 @@
 		adv |= ADVERTISE_PAUSE_CAP;
 	if (advertise & ADVERTISED_Asym_Pause)
 		adv |= ADVERTISE_PAUSE_ASYM;
-	phy_write(phy, MII_ADVERTISE, adv);
+	sungem_phy_write(phy, MII_ADVERTISE, adv);
 
 	/* Setup 1000BT advertise & enable crossover detect
 	 * XXX How do we advertise 1000BT ? Darwin source is
@@ -774,7 +774,7 @@
 	 * write to control... Someone has specs for those
 	 * beasts ?
 	 */
-	adv = phy_read(phy, MII_M1011_PHY_SPEC_CONTROL);
+	adv = sungem_phy_read(phy, MII_M1011_PHY_SPEC_CONTROL);
 	adv |= MII_M1011_PHY_SPEC_CONTROL_AUTO_MDIX;
 	adv &= ~(MII_1000BASETCONTROL_FULLDUPLEXCAP |
 			MII_1000BASETCONTROL_HALFDUPLEXCAP);
@@ -782,12 +782,12 @@
 		adv |= MII_1000BASETCONTROL_HALFDUPLEXCAP;
 	if (advertise & SUPPORTED_1000baseT_Full)
 		adv |= MII_1000BASETCONTROL_FULLDUPLEXCAP;
-	phy_write(phy, MII_1000BASETCONTROL, adv);
+	sungem_phy_write(phy, MII_1000BASETCONTROL, adv);
 
 	/* Start/Restart aneg */
-	ctl = phy_read(phy, MII_BMCR);
+	ctl = sungem_phy_read(phy, MII_BMCR);
 	ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
-	phy_write(phy, MII_BMCR, ctl);
+	sungem_phy_write(phy, MII_BMCR, ctl);
 
 	return 0;
 }
@@ -801,7 +801,7 @@
 	phy->duplex = fd;
 	phy->pause = 0;
 
-	ctl = phy_read(phy, MII_BMCR);
+	ctl = sungem_phy_read(phy, MII_BMCR);
 	ctl &= ~(BMCR_FULLDPLX|BMCR_SPEED100|BMCR_SPD2|BMCR_ANENABLE);
 	ctl |= BMCR_RESET;
 
@@ -824,7 +824,7 @@
 	/* Disable crossover. Again, the way Apple does it is strange,
 	 * though I don't assume they are wrong ;)
 	 */
-	ctl2 = phy_read(phy, MII_M1011_PHY_SPEC_CONTROL);
+	ctl2 = sungem_phy_read(phy, MII_M1011_PHY_SPEC_CONTROL);
 	ctl2 &= ~(MII_M1011_PHY_SPEC_CONTROL_MANUAL_MDIX |
 		MII_M1011_PHY_SPEC_CONTROL_AUTO_MDIX |
 		MII_1000BASETCONTROL_FULLDUPLEXCAP |
@@ -833,11 +833,11 @@
 		ctl2 |= (fd == DUPLEX_FULL) ?
 			MII_1000BASETCONTROL_FULLDUPLEXCAP :
 			MII_1000BASETCONTROL_HALFDUPLEXCAP;
-	phy_write(phy, MII_1000BASETCONTROL, ctl2);
+	sungem_phy_write(phy, MII_1000BASETCONTROL, ctl2);
 
 	// XXX Should we set the sungem to GII now on 1000BT ?
 
-	phy_write(phy, MII_BMCR, ctl);
+	sungem_phy_write(phy, MII_BMCR, ctl);
 
 	return 0;
 }
@@ -847,7 +847,7 @@
 	u16 status, pmask;
 
 	if (phy->autoneg) {
-		status = phy_read(phy, MII_M1011_PHY_SPEC_STATUS);
+		status = sungem_phy_read(phy, MII_M1011_PHY_SPEC_STATUS);
 		if ((status & MII_M1011_PHY_SPEC_STATUS_RESOLVED) == 0)
 			return -EAGAIN;
 		if (status & MII_M1011_PHY_SPEC_STATUS_1000)
@@ -1174,7 +1174,7 @@
 		goto fail;
 
 	/* Read ID and find matching entry */
-	id = (phy_read(phy, MII_PHYSID1) << 16 | phy_read(phy, MII_PHYSID2));
+	id = (sungem_phy_read(phy, MII_PHYSID1) << 16 | sungem_phy_read(phy, MII_PHYSID2));
 	printk(KERN_DEBUG KBUILD_MODNAME ": " "PHY ID: %x, addr: %x\n",
 	       id, mii_id);
 	for (i=0; (def = mii_phy_table[i]) != NULL; i++)
diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c
index 2470d9c..33dcc97 100644
--- a/drivers/net/usb/r8152.c
+++ b/drivers/net/usb/r8152.c
@@ -3151,8 +3151,8 @@
 {
 	struct r8152 *tp = netdev_priv(netdev);
 
-	strncpy(info->driver, MODULENAME, ETHTOOL_BUSINFO_LEN);
-	strncpy(info->version, DRIVER_VERSION, ETHTOOL_BUSINFO_LEN);
+	strlcpy(info->driver, MODULENAME, sizeof(info->driver));
+	strlcpy(info->version, DRIVER_VERSION, sizeof(info->version));
 	usb_make_path(tp->udev, info->bus_info, sizeof(info->bus_info));
 }
 
diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
index f0c2824..9359a13 100644
--- a/drivers/net/virtio_net.c
+++ b/drivers/net/virtio_net.c
@@ -953,7 +953,7 @@
 		}
 	}
 
-	if (!skb->xmit_more)
+	if (__netif_subqueue_stopped(dev, qnum) || !skb->xmit_more)
 		virtqueue_kick(sq->vq);
 
 	return NETDEV_TX_OK;
diff --git a/drivers/usb/gadget/function/f_ncm.c b/drivers/usb/gadget/function/f_ncm.c
index cb5d646..146f48c 100644
--- a/drivers/usb/gadget/function/f_ncm.c
+++ b/drivers/usb/gadget/function/f_ncm.c
@@ -1101,7 +1101,15 @@
 	/* Only send if data is available. */
 	if (ncm->skb_tx_data) {
 		ncm->timer_force_tx = true;
-		netdev_start_xmit(NULL, ncm->netdev);
+
+		/* XXX This allowance of a NULL skb argument to ndo_start_xmit
+		 * XXX is not sane.  The gadget layer should be redesigned so
+		 * XXX that the dev->wrap() invocations to build SKBs is transparent
+		 * XXX and performed in some way outside of the ndo_start_xmit
+		 * XXX interface.
+		 */
+		ncm->netdev->netdev_ops->ndo_start_xmit(NULL, ncm->netdev);
+
 		ncm->timer_force_tx = false;
 	}
 }
diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
index ee1431d9..5bd35cc 100644
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@@ -13,6 +13,8 @@
 #define PHY_ID_BCM5461			0x002060c0
 #define PHY_ID_BCM57780			0x03625d90
 
+#define PHY_ID_BCM7250			0xae025280
+#define PHY_ID_BCM7364			0xae025260
 #define PHY_ID_BCM7366			0x600d8490
 #define PHY_ID_BCM7439			0x600d8480
 #define PHY_ID_BCM7445			0x600d8510
@@ -21,9 +23,9 @@
 #define PHY_BCM_OUI_1			0x00206000
 #define PHY_BCM_OUI_2			0x0143bc00
 #define PHY_BCM_OUI_3			0x03625c00
-#define PHY_BCM_OUI_4			0x600d0000
+#define PHY_BCM_OUI_4			0x600d8400
 #define PHY_BCM_OUI_5			0x03625e00
-
+#define PHY_BCM_OUI_6			0xae025000
 
 #define PHY_BCM_FLAGS_MODE_COPPER	0x00000001
 #define PHY_BCM_FLAGS_MODE_1000BX	0x00000002
diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h
index 039b237..4298013 100644
--- a/include/linux/netdevice.h
+++ b/include/linux/netdevice.h
@@ -1781,24 +1781,13 @@
 #endif
 }
 
-static inline bool netdev_uses_dsa_tags(struct net_device *dev)
+static inline bool netdev_uses_dsa(struct net_device *dev)
 {
-#ifdef CONFIG_NET_DSA_TAG_DSA
+#ifdef CONFIG_NET_DSA
 	if (dev->dsa_ptr != NULL)
-		return dsa_uses_dsa_tags(dev->dsa_ptr);
+		return dsa_uses_tagged_protocol(dev->dsa_ptr);
 #endif
-
-	return 0;
-}
-
-static inline bool netdev_uses_trailer_tags(struct net_device *dev)
-{
-#ifdef CONFIG_NET_DSA_TAG_TRAILER
-	if (dev->dsa_ptr != NULL)
-		return dsa_uses_trailer_tags(dev->dsa_ptr);
-#endif
-
-	return 0;
+	return false;
 }
 
 /**
@@ -1933,6 +1922,13 @@
 	struct offload_callbacks callbacks;
 };
 
+struct dsa_device_ops {
+	netdev_tx_t (*xmit)(struct sk_buff *skb, struct net_device *dev);
+	int (*rcv)(struct sk_buff *skb, struct net_device *dev,
+		   struct packet_type *pt, struct net_device *orig_dev);
+};
+
+
 /* often modified stats are per cpu, other are shared (netdev->stats) */
 struct pcpu_sw_netstats {
 	u64     rx_packets;
diff --git a/include/linux/phy_fixed.h b/include/linux/phy_fixed.h
index ae612ac..9411386 100644
--- a/include/linux/phy_fixed.h
+++ b/include/linux/phy_fixed.h
@@ -18,6 +18,9 @@
 			      struct fixed_phy_status *status,
 			      struct device_node *np);
 extern void fixed_phy_del(int phy_addr);
+extern int fixed_phy_set_link_update(struct phy_device *phydev,
+			int (*link_update)(struct net_device *,
+					   struct fixed_phy_status *));
 #else
 static inline int fixed_phy_add(unsigned int irq, int phy_id,
 				struct fixed_phy_status *status)
@@ -34,14 +37,12 @@
 {
 	return -ENODEV;
 }
-#endif /* CONFIG_FIXED_PHY */
-
-/*
- * This function issued only by fixed_phy-aware drivers, no need
- * protect it with #ifdef
- */
-extern int fixed_phy_set_link_update(struct phy_device *phydev,
+static inline int fixed_phy_set_link_update(struct phy_device *phydev,
 			int (*link_update)(struct net_device *,
-					   struct fixed_phy_status *));
+					   struct fixed_phy_status *))
+{
+	return -ENODEV;
+}
+#endif /* CONFIG_FIXED_PHY */
 
 #endif /* __PHY_FIXED_H */
diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h
index 9b3802a..b69b7b5 100644
--- a/include/linux/skbuff.h
+++ b/include/linux/skbuff.h
@@ -580,7 +580,7 @@
 	__u8			encap_hdr_csum:1;
 	__u8			csum_valid:1;
 	__u8			csum_complete_sw:1;
-	/* 2/4 bit hole (depending on ndisc_nodetype presence) */
+	/* 1/3 bit hole (depending on ndisc_nodetype presence) */
 	kmemcheck_bitfield_end(flags2);
 
 #if defined CONFIG_NET_DMA || defined CONFIG_NET_RX_BUSY_POLL
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 6efce38..9771292 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -15,6 +15,14 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/workqueue.h>
+#include <linux/of.h>
+#include <linux/phy.h>
+#include <linux/phy_fixed.h>
+
+/* Not an official ethertype value, used only internally for DSA
+ * demultiplexing
+ */
+#define ETH_P_BRCMTAG		(ETH_P_XDSA + 1)
 
 #define DSA_MAX_SWITCHES	4
 #define DSA_MAX_PORTS		12
@@ -26,6 +34,12 @@
 	struct device	*mii_bus;
 	int		sw_addr;
 
+	/* Device tree node pointer for this specific switch chip
+	 * used during switch setup in case additional properties
+	 * and resources needs to be used
+	 */
+	struct device_node *of_node;
+
 	/*
 	 * The names of the switch's ports.  Use "cpu" to
 	 * designate the switch port that the cpu is connected to,
@@ -34,6 +48,7 @@
 	 * or any other string to indicate this is a physical port.
 	 */
 	char		*port_names[DSA_MAX_PORTS];
+	struct device_node *port_dn[DSA_MAX_PORTS];
 
 	/*
 	 * An array (with nr_chips elements) of which element [a]
@@ -59,6 +74,8 @@
 	struct dsa_chip_data	*chip;
 };
 
+struct dsa_device_ops;
+
 struct dsa_switch_tree {
 	/*
 	 * Configuration data for the platform device that owns
@@ -71,6 +88,7 @@
 	 * protocol to use.
 	 */
 	struct net_device	*master_netdev;
+	const struct dsa_device_ops	*ops;
 	__be16			tag_protocol;
 
 	/*
@@ -119,6 +137,7 @@
 	 */
 	u32			dsa_port_mask;
 	u32			phys_port_mask;
+	u32			phys_mii_mask;
 	struct mii_bus		*slave_mii_bus;
 	struct net_device	*ports[DSA_MAX_PORTS];
 };
@@ -170,6 +189,14 @@
 	void	(*poll_link)(struct dsa_switch *ds);
 
 	/*
+	 * Link state adjustment (called from libphy)
+	 */
+	void	(*adjust_link)(struct dsa_switch *ds, int port,
+				struct phy_device *phydev);
+	void	(*fixed_link_update)(struct dsa_switch *ds, int port,
+				struct fixed_phy_status *st);
+
+	/*
 	 * ethtool hardware statistics.
 	 */
 	void	(*get_strings)(struct dsa_switch *ds, int port, uint8_t *data);
@@ -186,21 +213,9 @@
 	return (void *)(ds + 1);
 }
 
-/*
- * The original DSA tag format and some other tag formats have no
- * ethertype, which means that we need to add a little hack to the
- * networking receive path to make sure that received frames get
- * the right ->protocol assigned to them when one of those tag
- * formats is in use.
- */
-static inline bool dsa_uses_dsa_tags(struct dsa_switch_tree *dst)
+static inline bool dsa_uses_tagged_protocol(struct dsa_switch_tree *dst)
 {
-	return !!(dst->tag_protocol == htons(ETH_P_DSA));
-}
-
-static inline bool dsa_uses_trailer_tags(struct dsa_switch_tree *dst)
-{
-	return !!(dst->tag_protocol == htons(ETH_P_TRAILER));
+	return dst->tag_protocol != 0;
 }
 
 #endif
diff --git a/include/uapi/linux/if_ether.h b/include/uapi/linux/if_ether.h
index 0f8210b..aa63ed0 100644
--- a/include/uapi/linux/if_ether.h
+++ b/include/uapi/linux/if_ether.h
@@ -128,6 +128,7 @@
 #define ETH_P_PHONET	0x00F5		/* Nokia Phonet frames          */
 #define ETH_P_IEEE802154 0x00F6		/* IEEE802.15.4 frame		*/
 #define ETH_P_CAIF	0x00F7		/* ST-Ericsson CAIF protocol	*/
+#define ETH_P_XDSA	0x00F8		/* Multiplexed DSA protocol	*/
 
 /*
  *	This is an Ethernet frame header.
diff --git a/net/dsa/Kconfig b/net/dsa/Kconfig
index f5eede1..a585fd6 100644
--- a/net/dsa/Kconfig
+++ b/net/dsa/Kconfig
@@ -12,6 +12,9 @@
 if NET_DSA
 
 # tagging formats
+config NET_DSA_TAG_BRCM
+	bool
+
 config NET_DSA_TAG_DSA
 	bool
 
diff --git a/net/dsa/Makefile b/net/dsa/Makefile
index 7b9fcbb..da06ed1 100644
--- a/net/dsa/Makefile
+++ b/net/dsa/Makefile
@@ -3,6 +3,7 @@
 dsa_core-y += dsa.o slave.o
 
 # tagging formats
+dsa_core-$(CONFIG_NET_DSA_TAG_BRCM) += tag_brcm.o
 dsa_core-$(CONFIG_NET_DSA_TAG_DSA) += tag_dsa.o
 dsa_core-$(CONFIG_NET_DSA_TAG_EDSA) += tag_edsa.o
 dsa_core-$(CONFIG_NET_DSA_TAG_TRAILER) += tag_trailer.o
diff --git a/net/dsa/dsa.c b/net/dsa/dsa.c
index 0a49632..484f695 100644
--- a/net/dsa/dsa.c
+++ b/net/dsa/dsa.c
@@ -144,6 +144,11 @@
 		goto out;
 	}
 
+	/* Make the built-in MII bus mask match the number of ports,
+	 * switch drivers can override this later
+	 */
+	ds->phys_mii_mask = ds->phys_port_mask;
+
 	/*
 	 * If the CPU connects to this switch, set the switch tree
 	 * tagging protocol to the preferred tagging format of this
@@ -410,6 +415,7 @@
 		chip_index++;
 		cd = &pd->chip[chip_index];
 
+		cd->of_node = child;
 		cd->mii_bus = &mdio_bus->dev;
 
 		sw_addr = of_get_property(child, "reg", NULL);
@@ -431,6 +437,8 @@
 			if (!port_name)
 				continue;
 
+			cd->port_dn[port_index] = port;
+
 			cd->port_names[port_index] = kstrdup(port_name,
 					GFP_KERNEL);
 			if (!cd->port_names[port_index]) {
@@ -608,7 +616,26 @@
 {
 }
 
+static int dsa_switch_rcv(struct sk_buff *skb, struct net_device *dev,
+			  struct packet_type *pt, struct net_device *orig_dev)
+{
+	struct dsa_switch_tree *dst = dev->dsa_ptr;
+
+	if (unlikely(dst == NULL)) {
+		kfree_skb(skb);
+		return 0;
+	}
+
+	return dst->ops->rcv(skb, dev, pt, orig_dev);
+}
+
+struct packet_type dsa_pack_type __read_mostly = {
+	.type	= cpu_to_be16(ETH_P_XDSA),
+	.func	= dsa_switch_rcv,
+};
+
 static const struct of_device_id dsa_of_match_table[] = {
+	{ .compatible = "brcm,bcm7445-switch-v4.0" },
 	{ .compatible = "marvell,dsa", },
 	{}
 };
@@ -633,30 +660,15 @@
 	if (rc)
 		return rc;
 
-#ifdef CONFIG_NET_DSA_TAG_DSA
-	dev_add_pack(&dsa_packet_type);
-#endif
-#ifdef CONFIG_NET_DSA_TAG_EDSA
-	dev_add_pack(&edsa_packet_type);
-#endif
-#ifdef CONFIG_NET_DSA_TAG_TRAILER
-	dev_add_pack(&trailer_packet_type);
-#endif
+	dev_add_pack(&dsa_pack_type);
+
 	return 0;
 }
 module_init(dsa_init_module);
 
 static void __exit dsa_cleanup_module(void)
 {
-#ifdef CONFIG_NET_DSA_TAG_TRAILER
-	dev_remove_pack(&trailer_packet_type);
-#endif
-#ifdef CONFIG_NET_DSA_TAG_EDSA
-	dev_remove_pack(&edsa_packet_type);
-#endif
-#ifdef CONFIG_NET_DSA_TAG_DSA
-	dev_remove_pack(&dsa_packet_type);
-#endif
+	dev_remove_pack(&dsa_pack_type);
 	platform_driver_unregister(&dsa_driver);
 }
 module_exit(dsa_cleanup_module);
diff --git a/net/dsa/dsa_priv.h b/net/dsa/dsa_priv.h
index d4cf5cc..98afed4 100644
--- a/net/dsa/dsa_priv.h
+++ b/net/dsa/dsa_priv.h
@@ -33,6 +33,10 @@
 	 * to this port.
 	 */
 	struct phy_device	*phy;
+	phy_interface_t		phy_interface;
+	int			old_link;
+	int			old_pause;
+	int			old_duplex;
 };
 
 /* dsa.c */
@@ -45,16 +49,16 @@
 				    int port, char *name);
 
 /* tag_dsa.c */
-netdev_tx_t dsa_xmit(struct sk_buff *skb, struct net_device *dev);
-extern struct packet_type dsa_packet_type;
+extern const struct dsa_device_ops dsa_netdev_ops;
 
 /* tag_edsa.c */
-netdev_tx_t edsa_xmit(struct sk_buff *skb, struct net_device *dev);
-extern struct packet_type edsa_packet_type;
+extern const struct dsa_device_ops edsa_netdev_ops;
 
 /* tag_trailer.c */
-netdev_tx_t trailer_xmit(struct sk_buff *skb, struct net_device *dev);
-extern struct packet_type trailer_packet_type;
+extern const struct dsa_device_ops trailer_netdev_ops;
+
+/* tag_brcm.c */
+extern const struct dsa_device_ops brcm_netdev_ops;
 
 
 #endif
diff --git a/net/dsa/slave.c b/net/dsa/slave.c
index 45a1e34..7333a4a 100644
--- a/net/dsa/slave.c
+++ b/net/dsa/slave.c
@@ -12,6 +12,8 @@
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
 #include <linux/phy.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
 #include "dsa_priv.h"
 
 /* slave mii_bus handling ***************************************************/
@@ -19,7 +21,7 @@
 {
 	struct dsa_switch *ds = bus->priv;
 
-	if (ds->phys_port_mask & (1 << addr))
+	if (ds->phys_mii_mask & (1 << addr))
 		return ds->drv->phy_read(ds, addr, reg);
 
 	return 0xffff;
@@ -29,7 +31,7 @@
 {
 	struct dsa_switch *ds = bus->priv;
 
-	if (ds->phys_port_mask & (1 << addr))
+	if (ds->phys_mii_mask & (1 << addr))
 		return ds->drv->phy_write(ds, addr, reg, val);
 
 	return 0;
@@ -171,6 +173,25 @@
 	return -EOPNOTSUPP;
 }
 
+static netdev_tx_t dsa_slave_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+	struct dsa_slave_priv *p = netdev_priv(dev);
+	struct dsa_switch_tree *dst = p->parent->dst;
+
+	return dst->ops->xmit(skb, dev);
+}
+
+static netdev_tx_t dsa_slave_notag_xmit(struct sk_buff *skb,
+					struct net_device *dev)
+{
+	struct dsa_slave_priv *p = netdev_priv(dev);
+
+	skb->dev = p->parent->dst->master_netdev;
+	dev_queue_xmit(skb);
+
+	return NETDEV_TX_OK;
+}
+
 
 /* ethtool operations *******************************************************/
 static int
@@ -293,44 +314,107 @@
 	.get_sset_count		= dsa_slave_get_sset_count,
 };
 
-#ifdef CONFIG_NET_DSA_TAG_DSA
-static const struct net_device_ops dsa_netdev_ops = {
+static const struct net_device_ops dsa_slave_netdev_ops = {
 	.ndo_init		= dsa_slave_init,
 	.ndo_open	 	= dsa_slave_open,
 	.ndo_stop		= dsa_slave_close,
-	.ndo_start_xmit		= dsa_xmit,
+	.ndo_start_xmit		= dsa_slave_xmit,
 	.ndo_change_rx_flags	= dsa_slave_change_rx_flags,
 	.ndo_set_rx_mode	= dsa_slave_set_rx_mode,
 	.ndo_set_mac_address	= dsa_slave_set_mac_address,
 	.ndo_do_ioctl		= dsa_slave_ioctl,
 };
-#endif
-#ifdef CONFIG_NET_DSA_TAG_EDSA
-static const struct net_device_ops edsa_netdev_ops = {
-	.ndo_init		= dsa_slave_init,
-	.ndo_open	 	= dsa_slave_open,
-	.ndo_stop		= dsa_slave_close,
-	.ndo_start_xmit		= edsa_xmit,
-	.ndo_change_rx_flags	= dsa_slave_change_rx_flags,
-	.ndo_set_rx_mode	= dsa_slave_set_rx_mode,
-	.ndo_set_mac_address	= dsa_slave_set_mac_address,
-	.ndo_do_ioctl		= dsa_slave_ioctl,
+
+static const struct dsa_device_ops notag_netdev_ops = {
+	.xmit	= dsa_slave_notag_xmit,
+	.rcv	= NULL,
 };
-#endif
-#ifdef CONFIG_NET_DSA_TAG_TRAILER
-static const struct net_device_ops trailer_netdev_ops = {
-	.ndo_init		= dsa_slave_init,
-	.ndo_open	 	= dsa_slave_open,
-	.ndo_stop		= dsa_slave_close,
-	.ndo_start_xmit		= trailer_xmit,
-	.ndo_change_rx_flags	= dsa_slave_change_rx_flags,
-	.ndo_set_rx_mode	= dsa_slave_set_rx_mode,
-	.ndo_set_mac_address	= dsa_slave_set_mac_address,
-	.ndo_do_ioctl		= dsa_slave_ioctl,
-};
-#endif
+
+static void dsa_slave_adjust_link(struct net_device *dev)
+{
+	struct dsa_slave_priv *p = netdev_priv(dev);
+	struct dsa_switch *ds = p->parent;
+	unsigned int status_changed = 0;
+
+	if (p->old_link != p->phy->link) {
+		status_changed = 1;
+		p->old_link = p->phy->link;
+	}
+
+	if (p->old_duplex != p->phy->duplex) {
+		status_changed = 1;
+		p->old_duplex = p->phy->duplex;
+	}
+
+	if (p->old_pause != p->phy->pause) {
+		status_changed = 1;
+		p->old_pause = p->phy->pause;
+	}
+
+	if (ds->drv->adjust_link && status_changed)
+		ds->drv->adjust_link(ds, p->port, p->phy);
+
+	if (status_changed)
+		phy_print_status(p->phy);
+}
+
+static int dsa_slave_fixed_link_update(struct net_device *dev,
+				       struct fixed_phy_status *status)
+{
+	struct dsa_slave_priv *p = netdev_priv(dev);
+	struct dsa_switch *ds = p->parent;
+
+	if (ds->drv->fixed_link_update)
+		ds->drv->fixed_link_update(ds, p->port, status);
+
+	return 0;
+}
 
 /* slave device setup *******************************************************/
+static void dsa_slave_phy_setup(struct dsa_slave_priv *p,
+				struct net_device *slave_dev)
+{
+	struct dsa_switch *ds = p->parent;
+	struct dsa_chip_data *cd = ds->pd;
+	struct device_node *phy_dn, *port_dn;
+	bool phy_is_fixed = false;
+	int ret;
+
+	port_dn = cd->port_dn[p->port];
+	p->phy_interface = of_get_phy_mode(port_dn);
+
+	phy_dn = of_parse_phandle(port_dn, "phy-handle", 0);
+	if (of_phy_is_fixed_link(port_dn)) {
+		/* In the case of a fixed PHY, the DT node associated
+		 * to the fixed PHY is the Port DT node
+		 */
+		ret = of_phy_register_fixed_link(port_dn);
+		if (ret) {
+			pr_err("failed to register fixed PHY\n");
+			return;
+		}
+		phy_is_fixed = true;
+		phy_dn = port_dn;
+	}
+
+	if (phy_dn)
+		p->phy = of_phy_connect(slave_dev, phy_dn,
+					dsa_slave_adjust_link, 0,
+					p->phy_interface);
+
+	if (p->phy && phy_is_fixed)
+		fixed_phy_set_link_update(p->phy, dsa_slave_fixed_link_update);
+
+	/* We could not connect to a designated PHY, so use the switch internal
+	 * MDIO bus instead
+	 */
+	if (!p->phy)
+		p->phy = ds->slave_mii_bus->phy_map[p->port];
+	else
+		pr_info("attached PHY at address %d [%s]\n",
+			p->phy->addr, p->phy->drv->name);
+}
+
 struct net_device *
 dsa_slave_create(struct dsa_switch *ds, struct device *parent,
 		 int port, char *name)
@@ -349,35 +433,48 @@
 	slave_dev->ethtool_ops = &dsa_slave_ethtool_ops;
 	eth_hw_addr_inherit(slave_dev, master);
 	slave_dev->tx_queue_len = 0;
+	slave_dev->netdev_ops = &dsa_slave_netdev_ops;
 
 	switch (ds->dst->tag_protocol) {
 #ifdef CONFIG_NET_DSA_TAG_DSA
 	case htons(ETH_P_DSA):
-		slave_dev->netdev_ops = &dsa_netdev_ops;
+		ds->dst->ops = &dsa_netdev_ops;
 		break;
 #endif
 #ifdef CONFIG_NET_DSA_TAG_EDSA
 	case htons(ETH_P_EDSA):
-		slave_dev->netdev_ops = &edsa_netdev_ops;
+		ds->dst->ops = &edsa_netdev_ops;
 		break;
 #endif
 #ifdef CONFIG_NET_DSA_TAG_TRAILER
 	case htons(ETH_P_TRAILER):
-		slave_dev->netdev_ops = &trailer_netdev_ops;
+		ds->dst->ops = &trailer_netdev_ops;
+		break;
+#endif
+#ifdef CONFIG_NET_DSA_TAG_BRCM
+	case htons(ETH_P_BRCMTAG):
+		ds->dst->ops = &brcm_netdev_ops;
 		break;
 #endif
 	default:
-		BUG();
+		ds->dst->ops = &notag_netdev_ops;
+		break;
 	}
 
 	SET_NETDEV_DEV(slave_dev, parent);
+	slave_dev->dev.of_node = ds->pd->port_dn[port];
 	slave_dev->vlan_features = master->vlan_features;
 
 	p = netdev_priv(slave_dev);
 	p->dev = slave_dev;
 	p->parent = ds;
 	p->port = port;
-	p->phy = ds->slave_mii_bus->phy_map[port];
+
+	p->old_pause = -1;
+	p->old_link = -1;
+	p->old_duplex = -1;
+
+	dsa_slave_phy_setup(p, slave_dev);
 
 	ret = register_netdev(slave_dev);
 	if (ret) {
diff --git a/net/dsa/tag_brcm.c b/net/dsa/tag_brcm.c
new file mode 100644
index 0000000..e0b759e
--- /dev/null
+++ b/net/dsa/tag_brcm.c
@@ -0,0 +1,173 @@
+/*
+ * Broadcom tag support
+ *
+ * Copyright (C) 2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/list.h>
+#include <linux/netdevice.h>
+#include <linux/slab.h>
+#include "dsa_priv.h"
+
+/* This tag length is 4 bytes, older ones were 6 bytes, we do not
+ * handle them
+ */
+#define BRCM_TAG_LEN	4
+
+/* Tag is constructed and desconstructed using byte by byte access
+ * because the tag is placed after the MAC Source Address, which does
+ * not make it 4-bytes aligned, so this might cause unaligned accesses
+ * on most systems where this is used.
+ */
+
+/* Ingress and egress opcodes */
+#define BRCM_OPCODE_SHIFT	5
+#define BRCM_OPCODE_MASK	0x7
+
+/* Ingress fields */
+/* 1st byte in the tag */
+#define BRCM_IG_TC_SHIFT	2
+#define BRCM_IG_TC_MASK		0x7
+/* 2nd byte in the tag */
+#define BRCM_IG_TE_MASK		0x3
+#define BRCM_IG_TS_SHIFT	7
+/* 3rd byte in the tag */
+#define BRCM_IG_DSTMAP2_MASK	1
+#define BRCM_IG_DSTMAP1_MASK	0xff
+
+/* Egress fields */
+
+/* 2nd byte in the tag */
+#define BRCM_EG_CID_MASK	0xff
+
+/* 3rd byte in the tag */
+#define BRCM_EG_RC_MASK		0xff
+#define  BRCM_EG_RC_RSVD	(3 << 6)
+#define  BRCM_EG_RC_EXCEPTION	(1 << 5)
+#define  BRCM_EG_RC_PROT_SNOOP	(1 << 4)
+#define  BRCM_EG_RC_PROT_TERM	(1 << 3)
+#define  BRCM_EG_RC_SWITCH	(1 << 2)
+#define  BRCM_EG_RC_MAC_LEARN	(1 << 1)
+#define  BRCM_EG_RC_MIRROR	(1 << 0)
+#define BRCM_EG_TC_SHIFT	5
+#define BRCM_EG_TC_MASK		0x7
+#define BRCM_EG_PID_MASK	0x1f
+
+static netdev_tx_t brcm_tag_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+	struct dsa_slave_priv *p = netdev_priv(dev);
+	u8 *brcm_tag;
+
+	dev->stats.tx_packets++;
+	dev->stats.tx_bytes += skb->len;
+
+	if (skb_cow_head(skb, BRCM_TAG_LEN) < 0)
+		goto out_free;
+
+	skb_push(skb, BRCM_TAG_LEN);
+
+	memmove(skb->data, skb->data + BRCM_TAG_LEN, 2 * ETH_ALEN);
+
+	/* Build the tag after the MAC Source Address */
+	brcm_tag = skb->data + 2 * ETH_ALEN;
+
+	/* Set the ingress opcode, traffic class, tag enforcment is
+	 * deprecated
+	 */
+	brcm_tag[0] = (1 << BRCM_OPCODE_SHIFT) |
+			((skb->priority << BRCM_IG_TC_SHIFT) & BRCM_IG_TC_MASK);
+	brcm_tag[1] = 0;
+	brcm_tag[2] = 0;
+	if (p->port == 8)
+		brcm_tag[2] = BRCM_IG_DSTMAP2_MASK;
+	brcm_tag[3] = (1 << p->port) & BRCM_IG_DSTMAP1_MASK;
+
+	/* Queue the SKB for transmission on the parent interface, but
+	 * do not modify its EtherType
+	 */
+	skb->protocol = htons(ETH_P_BRCMTAG);
+	skb->dev = p->parent->dst->master_netdev;
+	dev_queue_xmit(skb);
+
+	return NETDEV_TX_OK;
+
+out_free:
+	kfree_skb(skb);
+	return NETDEV_TX_OK;
+}
+
+static int brcm_tag_rcv(struct sk_buff *skb, struct net_device *dev,
+			struct packet_type *pt, struct net_device *orig_dev)
+{
+	struct dsa_switch_tree *dst = dev->dsa_ptr;
+	struct dsa_switch *ds;
+	int source_port;
+	u8 *brcm_tag;
+
+	if (unlikely(dst == NULL))
+		goto out_drop;
+
+	ds = dst->ds[0];
+
+	skb = skb_unshare(skb, GFP_ATOMIC);
+	if (skb == NULL)
+		goto out;
+
+	if (unlikely(!pskb_may_pull(skb, BRCM_TAG_LEN)))
+		goto out_drop;
+
+	/* skb->data points to the EtherType, the tag is right before it */
+	brcm_tag = skb->data - 2;
+
+	/* The opcode should never be different than 0b000 */
+	if (unlikely((brcm_tag[0] >> BRCM_OPCODE_SHIFT) & BRCM_OPCODE_MASK))
+		goto out_drop;
+
+	/* We should never see a reserved reason code without knowing how to
+	 * handle it
+	 */
+	WARN_ON(brcm_tag[2] & BRCM_EG_RC_RSVD);
+
+	/* Locate which port this is coming from */
+	source_port = brcm_tag[3] & BRCM_EG_PID_MASK;
+
+	/* Validate port against switch setup, either the port is totally */
+	if (source_port >= DSA_MAX_PORTS || ds->ports[source_port] == NULL)
+		goto out_drop;
+
+	/* Remove Broadcom tag and update checksum */
+	skb_pull_rcsum(skb, BRCM_TAG_LEN);
+
+	/* Move the Ethernet DA and SA */
+	memmove(skb->data - ETH_HLEN,
+		skb->data - ETH_HLEN - BRCM_TAG_LEN,
+		2 * ETH_ALEN);
+
+	skb_push(skb, ETH_HLEN);
+	skb->pkt_type = PACKET_HOST;
+	skb->dev = ds->ports[source_port];
+	skb->protocol = eth_type_trans(skb, skb->dev);
+
+	skb->dev->stats.rx_packets++;
+	skb->dev->stats.rx_bytes += skb->len;
+
+	netif_receive_skb(skb);
+
+	return 0;
+
+out_drop:
+	kfree_skb(skb);
+out:
+	return 0;
+}
+
+const struct dsa_device_ops brcm_netdev_ops = {
+	.xmit	= brcm_tag_xmit,
+	.rcv	= brcm_tag_rcv,
+};
diff --git a/net/dsa/tag_dsa.c b/net/dsa/tag_dsa.c
index cacce1e..d7dbc5b 100644
--- a/net/dsa/tag_dsa.c
+++ b/net/dsa/tag_dsa.c
@@ -16,7 +16,7 @@
 
 #define DSA_HLEN	4
 
-netdev_tx_t dsa_xmit(struct sk_buff *skb, struct net_device *dev)
+static netdev_tx_t dsa_xmit(struct sk_buff *skb, struct net_device *dev)
 {
 	struct dsa_slave_priv *p = netdev_priv(dev);
 	u8 *dsa_header;
@@ -186,7 +186,7 @@
 	return 0;
 }
 
-struct packet_type dsa_packet_type __read_mostly = {
-	.type	= cpu_to_be16(ETH_P_DSA),
-	.func	= dsa_rcv,
+const struct dsa_device_ops dsa_netdev_ops = {
+	.xmit	= dsa_xmit,
+	.rcv	= dsa_rcv,
 };
diff --git a/net/dsa/tag_edsa.c b/net/dsa/tag_edsa.c
index e70c43c..6b30abe 100644
--- a/net/dsa/tag_edsa.c
+++ b/net/dsa/tag_edsa.c
@@ -17,7 +17,7 @@
 #define DSA_HLEN	4
 #define EDSA_HLEN	8
 
-netdev_tx_t edsa_xmit(struct sk_buff *skb, struct net_device *dev)
+static netdev_tx_t edsa_xmit(struct sk_buff *skb, struct net_device *dev)
 {
 	struct dsa_slave_priv *p = netdev_priv(dev);
 	u8 *edsa_header;
@@ -205,7 +205,7 @@
 	return 0;
 }
 
-struct packet_type edsa_packet_type __read_mostly = {
-	.type	= cpu_to_be16(ETH_P_EDSA),
-	.func	= edsa_rcv,
+const struct dsa_device_ops edsa_netdev_ops = {
+	.xmit	= edsa_xmit,
+	.rcv	= edsa_rcv,
 };
diff --git a/net/dsa/tag_trailer.c b/net/dsa/tag_trailer.c
index 94bc260..5fe9444 100644
--- a/net/dsa/tag_trailer.c
+++ b/net/dsa/tag_trailer.c
@@ -14,7 +14,7 @@
 #include <linux/slab.h>
 #include "dsa_priv.h"
 
-netdev_tx_t trailer_xmit(struct sk_buff *skb, struct net_device *dev)
+static netdev_tx_t trailer_xmit(struct sk_buff *skb, struct net_device *dev)
 {
 	struct dsa_slave_priv *p = netdev_priv(dev);
 	struct sk_buff *nskb;
@@ -114,7 +114,7 @@
 	return 0;
 }
 
-struct packet_type trailer_packet_type __read_mostly = {
-	.type	= cpu_to_be16(ETH_P_TRAILER),
-	.func	= trailer_rcv,
+const struct dsa_device_ops trailer_netdev_ops = {
+	.xmit	= trailer_xmit,
+	.rcv	= trailer_rcv,
 };
diff --git a/net/ethernet/eth.c b/net/ethernet/eth.c
index f405e05..5cebca1 100644
--- a/net/ethernet/eth.c
+++ b/net/ethernet/eth.c
@@ -181,11 +181,8 @@
 	 * variants has been configured on the receiving interface,
 	 * and if so, set skb->protocol without looking at the packet.
 	 */
-	if (unlikely(netdev_uses_dsa_tags(dev)))
-		return htons(ETH_P_DSA);
-
-	if (unlikely(netdev_uses_trailer_tags(dev)))
-		return htons(ETH_P_TRAILER);
+	if (unlikely(netdev_uses_dsa(dev)))
+		return htons(ETH_P_XDSA);
 
 	if (likely(ntohs(eth->h_proto) >= ETH_P_802_3_MIN))
 		return eth->h_proto;
diff --git a/net/ipv4/syncookies.c b/net/ipv4/syncookies.c
index c0c7568..0431a8f 100644
--- a/net/ipv4/syncookies.c
+++ b/net/ipv4/syncookies.c
@@ -25,7 +25,7 @@
 
 extern int sysctl_tcp_syncookies;
 
-static u32 syncookie_secret[2][16-4+SHA_DIGEST_WORDS];
+static u32 syncookie_secret[2][16-4+SHA_DIGEST_WORDS] __read_mostly;
 
 #define COOKIEBITS 24	/* Upper bits store count */
 #define COOKIEMASK (((__u32)1 << COOKIEBITS) - 1)
diff --git a/net/ipv6/syncookies.c b/net/ipv6/syncookies.c
index 83cea1d..c643dc9 100644
--- a/net/ipv6/syncookies.c
+++ b/net/ipv6/syncookies.c
@@ -24,7 +24,7 @@
 #define COOKIEBITS 24	/* Upper bits store count */
 #define COOKIEMASK (((__u32)1 << COOKIEBITS) - 1)
 
-static u32 syncookie6_secret[2][16-4+SHA_DIGEST_WORDS];
+static u32 syncookie6_secret[2][16-4+SHA_DIGEST_WORDS] __read_mostly;
 
 /* RFC 2460, Section 8.3:
  * [ipv6 tcp] MSS must be computed as the maximum packet size minus 60 [..]