Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Fix incorrect use of loose in vpe.c
diff --git a/drivers/acpi/battery.c b/drivers/acpi/battery.c
index 4fb3c12..1423b0c 100644
--- a/drivers/acpi/battery.c
+++ b/drivers/acpi/battery.c
@@ -173,19 +173,7 @@
val->intval = battery->voltage_now * 1000;
break;
case POWER_SUPPLY_PROP_CURRENT_NOW:
- val->intval = battery->current_now;
- if (battery->power_unit) {
- val->intval *= 1000;
- } else {
- /*
- * If power units are mW, convert to mA by dividing by
- * current voltage.
- */
- if (battery->voltage_now)
- val->intval /= battery->voltage_now;
- else
- val->intval = -1;
- }
+ val->intval = battery->current_now * 1000;
break;
case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
case POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN:
diff --git a/drivers/char/serial167.c b/drivers/char/serial167.c
index 3b23270..a8f15e6 100644
--- a/drivers/char/serial167.c
+++ b/drivers/char/serial167.c
@@ -418,7 +418,7 @@
TTY_OVERRUN);
/*
If the flip buffer itself is
- overflowing, we still loose
+ overflowing, we still lose
the next incoming character.
*/
if (tty_buffer_request_room(tty, 1) !=
diff --git a/drivers/message/i2o/i2o_block.c b/drivers/message/i2o/i2o_block.c
index 84bdc2e..a443e13 100644
--- a/drivers/message/i2o/i2o_block.c
+++ b/drivers/message/i2o/i2o_block.c
@@ -354,7 +354,7 @@
* @req: the request to prepare
*
* Allocate the necessary i2o_block_request struct and connect it to
- * the request. This is needed that we not loose the SG list later on.
+ * the request. This is needed that we not lose the SG list later on.
*
* Returns BLKPREP_OK on success or BLKPREP_DEFER on failure.
*/
diff --git a/drivers/message/i2o/iop.c b/drivers/message/i2o/iop.c
index be2b592..6e53a30 100644
--- a/drivers/message/i2o/iop.c
+++ b/drivers/message/i2o/iop.c
@@ -49,7 +49,6 @@
/**
* i2o_msg_get_wait - obtain an I2O message from the IOP
* @c: I2O controller
- * @msg: pointer to a I2O message pointer
* @wait: how long to wait until timeout
*
* This function waits up to wait seconds for a message slot to be
diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c
index 6117d3d..28c00c3 100644
--- a/drivers/serial/mpc52xx_uart.c
+++ b/drivers/serial/mpc52xx_uart.c
@@ -591,8 +591,8 @@
/* Update the per-port timeout */
uart_update_timeout(port, new->c_cflag, baud);
- /* Do our best to flush TX & RX, so we don't loose anything */
- /* But we don't wait indefinitly ! */
+ /* Do our best to flush TX & RX, so we don't lose anything */
+ /* But we don't wait indefinitely ! */
j = 5000000; /* Maximum wait */
/* FIXME Can't receive chars since set_termios might be called at early
* boot for the console, all stuff is not yet ready to receive at that
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 51d7bde..aad1359 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -1498,7 +1498,7 @@
priv->interface, buf, 0, WDR_TIMEOUT);
/* Termios defaults are set by usb_serial_init. We don't change
- port->tty->termios - this would loose speed settings, etc.
+ port->tty->termios - this would lose speed settings, etc.
This is same behaviour as serial.c/rs_open() - Kuba */
/* ftdi_set_termios will send usb control messages */
