#ifndef LINUX_BCMA_DRIVER_CC_H_
#define LINUX_BCMA_DRIVER_CC_H_

/** ChipCommon core registers. **/
#define BCMA_CC_ID			0x0000
#define  BCMA_CC_ID_ID			0x0000FFFF
#define  BCMA_CC_ID_ID_SHIFT		0
#define  BCMA_CC_ID_REV			0x000F0000
#define  BCMA_CC_ID_REV_SHIFT		16
#define  BCMA_CC_ID_PKG			0x00F00000
#define  BCMA_CC_ID_PKG_SHIFT		20
#define  BCMA_CC_ID_NRCORES		0x0F000000
#define  BCMA_CC_ID_NRCORES_SHIFT	24
#define  BCMA_CC_ID_TYPE		0xF0000000
#define  BCMA_CC_ID_TYPE_SHIFT		28
#define BCMA_CC_CAP			0x0004		/* Capabilities */
#define  BCMA_CC_CAP_NRUART		0x00000003	/* # of UARTs */
#define  BCMA_CC_CAP_MIPSEB		0x00000004	/* MIPS in BigEndian Mode */
#define  BCMA_CC_CAP_UARTCLK		0x00000018	/* UART clock select */
#define   BCMA_CC_CAP_UARTCLK_INT	0x00000008	/* UARTs are driven by internal divided clock */
#define  BCMA_CC_CAP_UARTGPIO		0x00000020	/* UARTs on GPIO 15-12 */
#define  BCMA_CC_CAP_EXTBUS		0x000000C0	/* External buses present */
#define  BCMA_CC_CAP_FLASHT		0x00000700	/* Flash Type */
#define   BCMA_CC_FLASHT_NONE		0x00000000	/* No flash */
#define   BCMA_CC_FLASHT_STSER		0x00000100	/* ST serial flash */
#define   BCMA_CC_FLASHT_ATSER		0x00000200	/* Atmel serial flash */
#define   BCMA_CC_FLASHT_NFLASH		0x00000200
#define	  BCMA_CC_FLASHT_PARA		0x00000700	/* Parallel flash */
#define  BCMA_CC_CAP_PLLT		0x00038000	/* PLL Type */
#define   BCMA_PLLTYPE_NONE		0x00000000
#define   BCMA_PLLTYPE_1		0x00010000	/* 48Mhz base, 3 dividers */
#define   BCMA_PLLTYPE_2		0x00020000	/* 48Mhz, 4 dividers */
#define   BCMA_PLLTYPE_3		0x00030000	/* 25Mhz, 2 dividers */
#define   BCMA_PLLTYPE_4		0x00008000	/* 48Mhz, 4 dividers */
#define   BCMA_PLLTYPE_5		0x00018000	/* 25Mhz, 4 dividers */
#define   BCMA_PLLTYPE_6		0x00028000	/* 100/200 or 120/240 only */
#define   BCMA_PLLTYPE_7		0x00038000	/* 25Mhz, 4 dividers */
#define  BCMA_CC_CAP_PCTL		0x00040000	/* Power Control */
#define  BCMA_CC_CAP_OTPS		0x00380000	/* OTP size */
#define  BCMA_CC_CAP_OTPS_SHIFT		19
#define  BCMA_CC_CAP_OTPS_BASE		5
#define  BCMA_CC_CAP_JTAGM		0x00400000	/* JTAG master present */
#define  BCMA_CC_CAP_BROM		0x00800000	/* Internal boot ROM active */
#define  BCMA_CC_CAP_64BIT		0x08000000	/* 64-bit Backplane */
#define  BCMA_CC_CAP_PMU		0x10000000	/* PMU available (rev >= 20) */
#define  BCMA_CC_CAP_ECI		0x20000000	/* ECI available (rev >= 20) */
#define  BCMA_CC_CAP_SPROM		0x40000000	/* SPROM present */
#define BCMA_CC_CORECTL			0x0008
#define  BCMA_CC_CORECTL_UARTCLK0	0x00000001	/* Drive UART with internal clock */
#define	 BCMA_CC_CORECTL_SE		0x00000002	/* sync clk out enable (corerev >= 3) */
#define  BCMA_CC_CORECTL_UARTCLKEN	0x00000008	/* UART clock enable (rev >= 21) */
#define BCMA_CC_BIST			0x000C
#define BCMA_CC_OTPS			0x0010		/* OTP status */
#define	 BCMA_CC_OTPS_PROGFAIL		0x80000000
#define	 BCMA_CC_OTPS_PROTECT		0x00000007
#define	 BCMA_CC_OTPS_HW_PROTECT	0x00000001
#define	 BCMA_CC_OTPS_SW_PROTECT	0x00000002
#define	 BCMA_CC_OTPS_CID_PROTECT	0x00000004
#define  BCMA_CC_OTPS_GU_PROG_IND	0x00000F00	/* General Use programmed indication */
#define  BCMA_CC_OTPS_GU_PROG_IND_SHIFT	8
#define  BCMA_CC_OTPS_GU_PROG_HW	0x00000100	/* HW region programmed */
#define BCMA_CC_OTPC			0x0014		/* OTP control */
#define	 BCMA_CC_OTPC_RECWAIT		0xFF000000
#define	 BCMA_CC_OTPC_PROGWAIT		0x00FFFF00
#define	 BCMA_CC_OTPC_PRW_SHIFT		8
#define	 BCMA_CC_OTPC_MAXFAIL		0x00000038
#define	 BCMA_CC_OTPC_VSEL		0x00000006
#define	 BCMA_CC_OTPC_SELVL		0x00000001
#define BCMA_CC_OTPP			0x0018		/* OTP prog */
#define	 BCMA_CC_OTPP_COL		0x000000FF
#define	 BCMA_CC_OTPP_ROW		0x0000FF00
#define	 BCMA_CC_OTPP_ROW_SHIFT		8
#define	 BCMA_CC_OTPP_READERR		0x10000000
#define	 BCMA_CC_OTPP_VALUE		0x20000000
#define	 BCMA_CC_OTPP_READ		0x40000000
#define	 BCMA_CC_OTPP_START		0x80000000
#define	 BCMA_CC_OTPP_BUSY		0x80000000
#define BCMA_CC_OTPL			0x001C		/* OTP layout */
#define  BCMA_CC_OTPL_GURGN_OFFSET	0x00000FFF	/* offset of general use region */
#define BCMA_CC_IRQSTAT			0x0020
#define BCMA_CC_IRQMASK			0x0024
#define	 BCMA_CC_IRQ_GPIO		0x00000001	/* gpio intr */
#define	 BCMA_CC_IRQ_EXT		0x00000002	/* ro: ext intr pin (corerev >= 3) */
#define	 BCMA_CC_IRQ_WDRESET		0x80000000	/* watchdog reset occurred */
#define BCMA_CC_CHIPCTL			0x0028		/* Rev >= 11 only */
#define BCMA_CC_CHIPSTAT		0x002C		/* Rev >= 11 only */
#define  BCMA_CC_CHIPST_4313_SPROM_PRESENT	1
#define  BCMA_CC_CHIPST_4313_OTP_PRESENT	2
#define  BCMA_CC_CHIPST_4331_SPROM_PRESENT	2
#define  BCMA_CC_CHIPST_4331_OTP_PRESENT	4
#define BCMA_CC_JCMD			0x0030		/* Rev >= 10 only */
#define  BCMA_CC_JCMD_START		0x80000000
#define  BCMA_CC_JCMD_BUSY		0x80000000
#define  BCMA_CC_JCMD_PAUSE		0x40000000
#define  BCMA_CC_JCMD0_ACC_MASK		0x0000F000
#define  BCMA_CC_JCMD0_ACC_IRDR		0x00000000
#define  BCMA_CC_JCMD0_ACC_DR		0x00001000
#define  BCMA_CC_JCMD0_ACC_IR		0x00002000
#define  BCMA_CC_JCMD0_ACC_RESET	0x00003000
#define  BCMA_CC_JCMD0_ACC_IRPDR	0x00004000
#define  BCMA_CC_JCMD0_ACC_PDR		0x00005000
#define  BCMA_CC_JCMD0_IRW_MASK		0x00000F00
#define  BCMA_CC_JCMD_ACC_MASK		0x000F0000	/* Changes for corerev 11 */
#define  BCMA_CC_JCMD_ACC_IRDR		0x00000000
#define  BCMA_CC_JCMD_ACC_DR		0x00010000
#define  BCMA_CC_JCMD_ACC_IR		0x00020000
#define  BCMA_CC_JCMD_ACC_RESET		0x00030000
#define  BCMA_CC_JCMD_ACC_IRPDR		0x00040000
#define  BCMA_CC_JCMD_ACC_PDR		0x00050000
#define  BCMA_CC_JCMD_IRW_MASK		0x00001F00
#define  BCMA_CC_JCMD_IRW_SHIFT		8
#define  BCMA_CC_JCMD_DRW_MASK		0x0000003F
#define BCMA_CC_JIR			0x0034		/* Rev >= 10 only */
#define BCMA_CC_JDR			0x0038		/* Rev >= 10 only */
#define BCMA_CC_JCTL			0x003C		/* Rev >= 10 only */
#define  BCMA_CC_JCTL_FORCE_CLK		4		/* Force clock */
#define  BCMA_CC_JCTL_EXT_EN		2		/* Enable external targets */
#define  BCMA_CC_JCTL_EN		1		/* Enable Jtag master */
#define BCMA_CC_FLASHCTL		0x0040
#define  BCMA_CC_FLASHCTL_START		0x80000000
#define  BCMA_CC_FLASHCTL_BUSY		BCMA_CC_FLASHCTL_START
#define BCMA_CC_FLASHADDR		0x0044
#define BCMA_CC_FLASHDATA		0x0048
#define BCMA_CC_BCAST_ADDR		0x0050
#define BCMA_CC_BCAST_DATA		0x0054
#define BCMA_CC_GPIOPULLUP		0x0058		/* Rev >= 20 only */
#define BCMA_CC_GPIOPULLDOWN		0x005C		/* Rev >= 20 only */
#define BCMA_CC_GPIOIN			0x0060
#define BCMA_CC_GPIOOUT			0x0064
#define BCMA_CC_GPIOOUTEN		0x0068
#define BCMA_CC_GPIOCTL			0x006C
#define BCMA_CC_GPIOPOL			0x0070
#define BCMA_CC_GPIOIRQ			0x0074
#define BCMA_CC_WATCHDOG		0x0080
#define BCMA_CC_GPIOTIMER		0x0088		/* LED powersave (corerev >= 16) */
#define  BCMA_CC_GPIOTIMER_OFFTIME	0x0000FFFF
#define  BCMA_CC_GPIOTIMER_OFFTIME_SHIFT	0
#define  BCMA_CC_GPIOTIMER_ONTIME	0xFFFF0000
#define  BCMA_CC_GPIOTIMER_ONTIME_SHIFT	16
#define BCMA_CC_GPIOTOUTM		0x008C		/* LED powersave (corerev >= 16) */
#define BCMA_CC_CLOCK_N			0x0090
#define BCMA_CC_CLOCK_SB		0x0094
#define BCMA_CC_CLOCK_PCI		0x0098
#define BCMA_CC_CLOCK_M2		0x009C
#define BCMA_CC_CLOCK_MIPS		0x00A0
#define BCMA_CC_CLKDIV			0x00A4		/* Rev >= 3 only */
#define	 BCMA_CC_CLKDIV_SFLASH		0x0F000000
#define	 BCMA_CC_CLKDIV_SFLASH_SHIFT	24
#define	 BCMA_CC_CLKDIV_OTP		0x000F0000
#define	 BCMA_CC_CLKDIV_OTP_SHIFT	16
#define	 BCMA_CC_CLKDIV_JTAG		0x00000F00
#define	 BCMA_CC_CLKDIV_JTAG_SHIFT	8
#define	 BCMA_CC_CLKDIV_UART		0x000000FF
#define BCMA_CC_CAP_EXT			0x00AC		/* Capabilities */
#define BCMA_CC_PLLONDELAY		0x00B0		/* Rev >= 4 only */
#define BCMA_CC_FREFSELDELAY		0x00B4		/* Rev >= 4 only */
#define BCMA_CC_SLOWCLKCTL		0x00B8		/* 6 <= Rev <= 9 only */
#define  BCMA_CC_SLOWCLKCTL_SRC		0x00000007	/* slow clock source mask */
#define	  BCMA_CC_SLOWCLKCTL_SRC_LPO	0x00000000	/* source of slow clock is LPO */
#define   BCMA_CC_SLOWCLKCTL_SRC_XTAL	0x00000001	/* source of slow clock is crystal */
#define	  BCMA_CC_SLOECLKCTL_SRC_PCI	0x00000002	/* source of slow clock is PCI */
#define  BCMA_CC_SLOWCLKCTL_LPOFREQ	0x00000200	/* LPOFreqSel, 1: 160Khz, 0: 32KHz */
#define  BCMA_CC_SLOWCLKCTL_LPOPD	0x00000400	/* LPOPowerDown, 1: LPO is disabled, 0: LPO is enabled */
#define  BCMA_CC_SLOWCLKCTL_FSLOW	0x00000800	/* ForceSlowClk, 1: sb/cores running on slow clock, 0: power logic control */
#define  BCMA_CC_SLOWCLKCTL_IPLL	0x00001000	/* IgnorePllOffReq, 1/0: power logic ignores/honors PLL clock disable requests from core */
#define  BCMA_CC_SLOWCLKCTL_ENXTAL	0x00002000	/* XtalControlEn, 1/0: power logic does/doesn't disable crystal when appropriate */
#define  BCMA_CC_SLOWCLKCTL_XTALPU	0x00004000	/* XtalPU (RO), 1/0: crystal running/disabled */
#define  BCMA_CC_SLOWCLKCTL_CLKDIV	0xFFFF0000	/* ClockDivider (SlowClk = 1/(4+divisor)) */
#define  BCMA_CC_SLOWCLKCTL_CLKDIV_SHIFT	16
#define BCMA_CC_SYSCLKCTL		0x00C0		/* Rev >= 3 only */
#define	 BCMA_CC_SYSCLKCTL_IDLPEN	0x00000001	/* ILPen: Enable Idle Low Power */
#define	 BCMA_CC_SYSCLKCTL_ALPEN	0x00000002	/* ALPen: Enable Active Low Power */
#define	 BCMA_CC_SYSCLKCTL_PLLEN	0x00000004	/* ForcePLLOn */
#define	 BCMA_CC_SYSCLKCTL_FORCEALP	0x00000008	/* Force ALP (or HT if ALPen is not set */
#define	 BCMA_CC_SYSCLKCTL_FORCEHT	0x00000010	/* Force HT */
#define  BCMA_CC_SYSCLKCTL_CLKDIV	0xFFFF0000	/* ClkDiv  (ILP = 1/(4+divisor)) */
#define  BCMA_CC_SYSCLKCTL_CLKDIV_SHIFT	16
#define BCMA_CC_CLKSTSTR		0x00C4		/* Rev >= 3 only */
#define BCMA_CC_EROM			0x00FC
#define BCMA_CC_PCMCIA_CFG		0x0100
#define BCMA_CC_PCMCIA_MEMWAIT		0x0104
#define BCMA_CC_PCMCIA_ATTRWAIT		0x0108
#define BCMA_CC_PCMCIA_IOWAIT		0x010C
#define BCMA_CC_IDE_CFG			0x0110
#define BCMA_CC_IDE_MEMWAIT		0x0114
#define BCMA_CC_IDE_ATTRWAIT		0x0118
#define BCMA_CC_IDE_IOWAIT		0x011C
#define BCMA_CC_PROG_CFG		0x0120
#define BCMA_CC_PROG_WAITCNT		0x0124
#define BCMA_CC_FLASH_CFG		0x0128
#define  BCMA_CC_FLASH_CFG_DS		0x0010	/* Data size, 0=8bit, 1=16bit */
#define BCMA_CC_FLASH_WAITCNT		0x012C
#define BCMA_CC_SROM_CONTROL		0x0190
#define  BCMA_CC_SROM_CONTROL_START	0x80000000
#define  BCMA_CC_SROM_CONTROL_BUSY	0x80000000
#define  BCMA_CC_SROM_CONTROL_OPCODE	0x60000000
#define  BCMA_CC_SROM_CONTROL_OP_READ	0x00000000
#define  BCMA_CC_SROM_CONTROL_OP_WRITE	0x20000000
#define  BCMA_CC_SROM_CONTROL_OP_WRDIS	0x40000000
#define  BCMA_CC_SROM_CONTROL_OP_WREN	0x60000000
#define  BCMA_CC_SROM_CONTROL_OTPSEL	0x00000010
#define  BCMA_CC_SROM_CONTROL_LOCK	0x00000008
#define  BCMA_CC_SROM_CONTROL_SIZE_MASK	0x00000006
#define  BCMA_CC_SROM_CONTROL_SIZE_1K	0x00000000
#define  BCMA_CC_SROM_CONTROL_SIZE_4K	0x00000002
#define  BCMA_CC_SROM_CONTROL_SIZE_16K	0x00000004
#define  BCMA_CC_SROM_CONTROL_SIZE_SHIFT	1
#define  BCMA_CC_SROM_CONTROL_PRESENT	0x00000001
/* 0x1E0 is defined as shared BCMA_CLKCTLST */
#define BCMA_CC_HW_WORKAROUND		0x01E4 /* Hardware workaround (rev >= 20) */
#define BCMA_CC_UART0_DATA		0x0300
#define BCMA_CC_UART0_IMR		0x0304
#define BCMA_CC_UART0_FCR		0x0308
#define BCMA_CC_UART0_LCR		0x030C
#define BCMA_CC_UART0_MCR		0x0310
#define BCMA_CC_UART0_LSR		0x0314
#define BCMA_CC_UART0_MSR		0x0318
#define BCMA_CC_UART0_SCRATCH		0x031C
#define BCMA_CC_UART1_DATA		0x0400
#define BCMA_CC_UART1_IMR		0x0404
#define BCMA_CC_UART1_FCR		0x0408
#define BCMA_CC_UART1_LCR		0x040C
#define BCMA_CC_UART1_MCR		0x0410
#define BCMA_CC_UART1_LSR		0x0414
#define BCMA_CC_UART1_MSR		0x0418
#define BCMA_CC_UART1_SCRATCH		0x041C
/* PMU registers (rev >= 20) */
#define BCMA_CC_PMU_CTL			0x0600 /* PMU control */
#define  BCMA_CC_PMU_CTL_ILP_DIV	0xFFFF0000 /* ILP div mask */
#define  BCMA_CC_PMU_CTL_ILP_DIV_SHIFT	16
#define  BCMA_CC_PMU_CTL_PLL_UPD	0x00000400
#define  BCMA_CC_PMU_CTL_NOILPONW	0x00000200 /* No ILP on wait */
#define  BCMA_CC_PMU_CTL_HTREQEN	0x00000100 /* HT req enable */
#define  BCMA_CC_PMU_CTL_ALPREQEN	0x00000080 /* ALP req enable */
#define  BCMA_CC_PMU_CTL_XTALFREQ	0x0000007C /* Crystal freq */
#define  BCMA_CC_PMU_CTL_XTALFREQ_SHIFT	2
#define  BCMA_CC_PMU_CTL_ILPDIVEN	0x00000002 /* ILP div enable */
#define  BCMA_CC_PMU_CTL_LPOSEL		0x00000001 /* LPO sel */
#define BCMA_CC_PMU_CAP			0x0604 /* PMU capabilities */
#define  BCMA_CC_PMU_CAP_REVISION	0x000000FF /* Revision mask */
#define BCMA_CC_PMU_STAT		0x0608 /* PMU status */
#define  BCMA_CC_PMU_STAT_INTPEND	0x00000040 /* Interrupt pending */
#define  BCMA_CC_PMU_STAT_SBCLKST	0x00000030 /* Backplane clock status? */
#define  BCMA_CC_PMU_STAT_HAVEALP	0x00000008 /* ALP available */
#define  BCMA_CC_PMU_STAT_HAVEHT	0x00000004 /* HT available */
#define  BCMA_CC_PMU_STAT_RESINIT	0x00000003 /* Res init */
#define BCMA_CC_PMU_RES_STAT		0x060C /* PMU res status */
#define BCMA_CC_PMU_RES_PEND		0x0610 /* PMU res pending */
#define BCMA_CC_PMU_TIMER		0x0614 /* PMU timer */
#define BCMA_CC_PMU_MINRES_MSK		0x0618 /* PMU min res mask */
#define BCMA_CC_PMU_MAXRES_MSK		0x061C /* PMU max res mask */
#define BCMA_CC_PMU_RES_TABSEL		0x0620 /* PMU res table sel */
#define BCMA_CC_PMU_RES_DEPMSK		0x0624 /* PMU res dep mask */
#define BCMA_CC_PMU_RES_UPDNTM		0x0628 /* PMU res updown timer */
#define BCMA_CC_PMU_RES_TIMER		0x062C /* PMU res timer */
#define BCMA_CC_PMU_CLKSTRETCH		0x0630 /* PMU clockstretch */
#define BCMA_CC_PMU_WATCHDOG		0x0634 /* PMU watchdog */
#define BCMA_CC_PMU_RES_REQTS		0x0640 /* PMU res req timer sel */
#define BCMA_CC_PMU_RES_REQT		0x0644 /* PMU res req timer */
#define BCMA_CC_PMU_RES_REQM		0x0648 /* PMU res req mask */
#define BCMA_CC_CHIPCTL_ADDR		0x0650
#define BCMA_CC_CHIPCTL_DATA		0x0654
#define BCMA_CC_REGCTL_ADDR		0x0658
#define BCMA_CC_REGCTL_DATA		0x065C
#define BCMA_CC_PLLCTL_ADDR		0x0660
#define BCMA_CC_PLLCTL_DATA		0x0664
#define BCMA_CC_SPROM			0x0800 /* SPROM beginning */

/* Divider allocation in 4716/47162/5356 */
#define BCMA_CC_PMU5_MAINPLL_CPU	1
#define BCMA_CC_PMU5_MAINPLL_MEM	2
#define BCMA_CC_PMU5_MAINPLL_SSB	3

/* PLL usage in 4716/47162 */
#define BCMA_CC_PMU4716_MAINPLL_PLL0	12

/* PLL usage in 5356/5357 */
#define BCMA_CC_PMU5356_MAINPLL_PLL0	0
#define BCMA_CC_PMU5357_MAINPLL_PLL0	0

/* 4706 PMU */
#define BCMA_CC_PMU4706_MAINPLL_PLL0	0

/* ALP clock on pre-PMU chips */
#define BCMA_CC_PMU_ALP_CLOCK		20000000
/* HT clock for systems with PMU-enabled chipcommon */
#define BCMA_CC_PMU_HT_CLOCK		80000000

/* PMU rev 5 (& 6) */
#define BCMA_CC_PPL_P1P2_OFF		0
#define BCMA_CC_PPL_P1_MASK		0x0f000000
#define BCMA_CC_PPL_P1_SHIFT		24
#define BCMA_CC_PPL_P2_MASK		0x00f00000
#define BCMA_CC_PPL_P2_SHIFT		20
#define BCMA_CC_PPL_M14_OFF		1
#define BCMA_CC_PPL_MDIV_MASK		0x000000ff
#define BCMA_CC_PPL_MDIV_WIDTH		8
#define BCMA_CC_PPL_NM5_OFF		2
#define BCMA_CC_PPL_NDIV_MASK		0xfff00000
#define BCMA_CC_PPL_NDIV_SHIFT		20
#define BCMA_CC_PPL_FMAB_OFF		3
#define BCMA_CC_PPL_MRAT_MASK		0xf0000000
#define BCMA_CC_PPL_MRAT_SHIFT		28
#define BCMA_CC_PPL_ABRAT_MASK		0x08000000
#define BCMA_CC_PPL_ABRAT_SHIFT		27
#define BCMA_CC_PPL_FDIV_MASK		0x07ffffff
#define BCMA_CC_PPL_PLLCTL_OFF		4
#define BCMA_CC_PPL_PCHI_OFF		5
#define BCMA_CC_PPL_PCHI_MASK		0x0000003f

/* BCM4331 ChipControl numbers. */
#define BCMA_CHIPCTL_4331_BT_COEXIST		BIT(0)	/* 0 disable */
#define BCMA_CHIPCTL_4331_SECI			BIT(1)	/* 0 SECI is disabled (JATG functional) */
#define BCMA_CHIPCTL_4331_EXT_LNA		BIT(2)	/* 0 disable */
#define BCMA_CHIPCTL_4331_SPROM_GPIO13_15	BIT(3)	/* sprom/gpio13-15 mux */
#define BCMA_CHIPCTL_4331_EXTPA_EN		BIT(4)	/* 0 ext pa disable, 1 ext pa enabled */
#define BCMA_CHIPCTL_4331_GPIOCLK_ON_SPROMCS	BIT(5)	/* set drive out GPIO_CLK on sprom_cs pin */
#define BCMA_CHIPCTL_4331_PCIE_MDIO_ON_SPROMCS	BIT(6)	/* use sprom_cs pin as PCIE mdio interface */
#define BCMA_CHIPCTL_4331_EXTPA_ON_GPIO2_5	BIT(7)	/* aband extpa will be at gpio2/5 and sprom_dout */
#define BCMA_CHIPCTL_4331_OVR_PIPEAUXCLKEN	BIT(8)	/* override core control on pipe_AuxClkEnable */
#define BCMA_CHIPCTL_4331_OVR_PIPEAUXPWRDOWN	BIT(9)	/* override core control on pipe_AuxPowerDown */
#define BCMA_CHIPCTL_4331_PCIE_AUXCLKEN		BIT(10)	/* pcie_auxclkenable */
#define BCMA_CHIPCTL_4331_PCIE_PIPE_PLLDOWN	BIT(11)	/* pcie_pipe_pllpowerdown */
#define BCMA_CHIPCTL_4331_BT_SHD0_ON_GPIO4	BIT(16)	/* enable bt_shd0 at gpio4 */
#define BCMA_CHIPCTL_4331_BT_SHD1_ON_GPIO5	BIT(17)	/* enable bt_shd1 at gpio5 */

/* Data for the PMU, if available.
 * Check availability with ((struct bcma_chipcommon)->capabilities & BCMA_CC_CAP_PMU)
 */
struct bcma_chipcommon_pmu {
	u8 rev;			/* PMU revision */
	u32 crystalfreq;	/* The active crystal frequency (in kHz) */
};

#ifdef CONFIG_BCMA_DRIVER_MIPS
struct bcma_pflash {
	u8 buswidth;
	u32 window;
	u32 window_size;
};

struct bcma_serial_port {
	void *regs;
	unsigned long clockspeed;
	unsigned int irq;
	unsigned int baud_base;
	unsigned int reg_shift;
};
#endif /* CONFIG_BCMA_DRIVER_MIPS */

struct bcma_drv_cc {
	struct bcma_device *core;
	u32 status;
	u32 capabilities;
	u32 capabilities_ext;
	u8 setup_done:1;
	/* Fast Powerup Delay constant */
	u16 fast_pwrup_delay;
	struct bcma_chipcommon_pmu pmu;
#ifdef CONFIG_BCMA_DRIVER_MIPS
	struct bcma_pflash pflash;

	int nr_serial_ports;
	struct bcma_serial_port serial_ports[4];
#endif /* CONFIG_BCMA_DRIVER_MIPS */
};

/* Register access */
#define bcma_cc_read32(cc, offset) \
	bcma_read32((cc)->core, offset)
#define bcma_cc_write32(cc, offset, val) \
	bcma_write32((cc)->core, offset, val)

#define bcma_cc_mask32(cc, offset, mask) \
	bcma_cc_write32(cc, offset, bcma_cc_read32(cc, offset) & (mask))
#define bcma_cc_set32(cc, offset, set) \
	bcma_cc_write32(cc, offset, bcma_cc_read32(cc, offset) | (set))
#define bcma_cc_maskset32(cc, offset, mask, set) \
	bcma_cc_write32(cc, offset, (bcma_cc_read32(cc, offset) & (mask)) | (set))

extern void bcma_core_chipcommon_init(struct bcma_drv_cc *cc);

extern void bcma_chipco_suspend(struct bcma_drv_cc *cc);
extern void bcma_chipco_resume(struct bcma_drv_cc *cc);

void bcma_chipco_bcm4331_ext_pa_lines_ctl(struct bcma_drv_cc *cc, bool enable);

extern void bcma_chipco_watchdog_timer_set(struct bcma_drv_cc *cc,
					  u32 ticks);

void bcma_chipco_irq_mask(struct bcma_drv_cc *cc, u32 mask, u32 value);

u32 bcma_chipco_irq_status(struct bcma_drv_cc *cc, u32 mask);

/* Chipcommon GPIO pin access. */
u32 bcma_chipco_gpio_in(struct bcma_drv_cc *cc, u32 mask);
u32 bcma_chipco_gpio_out(struct bcma_drv_cc *cc, u32 mask, u32 value);
u32 bcma_chipco_gpio_outen(struct bcma_drv_cc *cc, u32 mask, u32 value);
u32 bcma_chipco_gpio_control(struct bcma_drv_cc *cc, u32 mask, u32 value);
u32 bcma_chipco_gpio_intmask(struct bcma_drv_cc *cc, u32 mask, u32 value);
u32 bcma_chipco_gpio_polarity(struct bcma_drv_cc *cc, u32 mask, u32 value);

/* PMU support */
extern void bcma_pmu_init(struct bcma_drv_cc *cc);

extern void bcma_chipco_pll_write(struct bcma_drv_cc *cc, u32 offset,
				  u32 value);
extern void bcma_chipco_pll_maskset(struct bcma_drv_cc *cc, u32 offset,
				    u32 mask, u32 set);
extern void bcma_chipco_chipctl_maskset(struct bcma_drv_cc *cc,
					u32 offset, u32 mask, u32 set);
extern void bcma_chipco_regctl_maskset(struct bcma_drv_cc *cc,
				       u32 offset, u32 mask, u32 set);

#endif /* LINUX_BCMA_DRIVER_CC_H_ */