// SPDX-License-Identifier: GPL-2.0
/*
 * Driver for the Apex chip.
 *
 * Copyright (C) 2018 Google, Inc.
 */

#include <linux/atomic.h>
#include <linux/compiler.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/fs.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/pci.h>
#include <linux/printk.h>
#include <linux/sched.h>
#include <linux/uaccess.h>
#include <linux/workqueue.h>

#include "apex.h"

#include "gasket_core.h"
#include "gasket_interrupt.h"
#include "gasket_page_table.h"
#include "gasket_sysfs.h"

/* Constants */
#define APEX_DEVICE_NAME "Apex"
#define APEX_DRIVER_VERSION "1.1"

/* CSRs are in BAR 2. */
#define APEX_BAR_INDEX 2

#define APEX_PCI_VENDOR_ID 0x1ac1
#define APEX_PCI_DEVICE_ID 0x089a

/* Bar Offsets. */
#define APEX_BAR_OFFSET 0
#define APEX_CM_OFFSET 0x1000000

/* The sizes of each Apex BAR 2. */
#define APEX_BAR_BYTES 0x100000
#define APEX_CH_MEM_BYTES (PAGE_SIZE * MAX_NUM_COHERENT_PAGES)

/* The number of user-mappable memory ranges in BAR2 of a Apex chip. */
#define NUM_REGIONS 3

/* The number of nodes in a Apex chip. */
#define NUM_NODES 1

/*
 * The total number of entries in the page table. Should match the value read
 * from the register APEX_BAR2_REG_KERNEL_HIB_PAGE_TABLE_SIZE.
 */
#define APEX_PAGE_TABLE_TOTAL_ENTRIES 8192

#define APEX_EXTENDED_SHIFT 63 /* Extended address bit position. */

/* Check reset 120 times */
#define APEX_RESET_RETRY 120
/* Wait 100 ms between checks. Total 12 sec wait maximum. */
#define APEX_RESET_DELAY 100

/* Interval between temperature polls, 0 disables polling */
#define DEFAULT_APEX_TEMP_POLL_INTERVAL 5000

/* apex device private data */
struct apex_dev {
	struct gasket_dev *gasket_dev_ptr;
	struct delayed_work check_temperature_work;
	u32 adc_trip_points[3];
	atomic_t temp_poll_interval;
};

/* Enumeration of the supported sysfs entries. */
enum sysfs_attribute_type {
	ATTR_KERNEL_HIB_PAGE_TABLE_SIZE,
	ATTR_KERNEL_HIB_SIMPLE_PAGE_TABLE_SIZE,
	ATTR_KERNEL_HIB_NUM_ACTIVE_PAGES,
	ATTR_TEMP,
	ATTR_TEMP_WARN1,
	ATTR_TEMP_WARN1_EN,
	ATTR_TEMP_WARN2,
	ATTR_TEMP_WARN2_EN,
	ATTR_TEMP_TRIP0,
	ATTR_TEMP_TRIP1,
	ATTR_TEMP_TRIP2,
	ATTR_TEMP_POLL_INTERVAL,
	ATTR_UNIQUE_ID,
};

/*
 * Register offsets into BAR2 memory.
 * Only values necessary for driver implementation are defined.
 */
enum apex_bar2_regs {
	APEX_BAR2_REG_SCU_BASE = 0x1A300,
	APEX_BAR2_REG_KERNEL_HIB_PAGE_TABLE_SIZE = 0x46000,
	APEX_BAR2_REG_KERNEL_HIB_EXTENDED_TABLE = 0x46008,
	APEX_BAR2_REG_KERNEL_HIB_TRANSLATION_ENABLE = 0x46010,
	APEX_BAR2_REG_KERNEL_HIB_INSTR_QUEUE_INTVECCTL = 0x46018,
	APEX_BAR2_REG_KERNEL_HIB_INPUT_ACTV_QUEUE_INTVECCTL = 0x46020,
	APEX_BAR2_REG_KERNEL_HIB_PARAM_QUEUE_INTVECCTL = 0x46028,
	APEX_BAR2_REG_KERNEL_HIB_OUTPUT_ACTV_QUEUE_INTVECCTL = 0x46030,
	APEX_BAR2_REG_KERNEL_HIB_SC_HOST_INTVECCTL = 0x46038,
	APEX_BAR2_REG_KERNEL_HIB_TOP_LEVEL_INTVECCTL = 0x46040,
	APEX_BAR2_REG_KERNEL_HIB_FATAL_ERR_INTVECCTL = 0x46048,
	APEX_BAR2_REG_KERNEL_HIB_DMA_PAUSE = 0x46050,
	APEX_BAR2_REG_KERNEL_HIB_DMA_PAUSE_MASK = 0x46058,
	APEX_BAR2_REG_KERNEL_HIB_STATUS_BLOCK_DELAY = 0x46060,
	APEX_BAR2_REG_KERNEL_HIB_MSIX_PENDING_BIT_ARRAY0 = 0x46068,
	APEX_BAR2_REG_KERNEL_HIB_MSIX_PENDING_BIT_ARRAY1 = 0x46070,
	APEX_BAR2_REG_KERNEL_HIB_PAGE_TABLE_INIT = 0x46078,
	APEX_BAR2_REG_KERNEL_HIB_MSIX_TABLE_INIT = 0x46080,
	APEX_BAR2_REG_KERNEL_WIRE_INT_PENDING_BIT_ARRAY = 0x48778,
	APEX_BAR2_REG_KERNEL_WIRE_INT_MASK_ARRAY = 0x48780,
	APEX_BAR2_REG_USER_HIB_DMA_PAUSE = 0x486D8,
	APEX_BAR2_REG_USER_HIB_DMA_PAUSED = 0x486E0,
	APEX_BAR2_REG_IDLEGENERATOR_IDLEGEN_IDLEREGISTER = 0x4A000,
	APEX_BAR2_REG_KERNEL_HIB_PAGE_TABLE = 0x50000,
	APEX_BAR2_REG_OMC0_D0 = 0x01a0d0,
	APEX_BAR2_REG_OMC0_D4 = 0x01a0d4,
	APEX_BAR2_REG_OMC0_D8 = 0x01a0d8,
	APEX_BAR2_REG_OMC0_DC = 0x01a0dc,
	APEX_BAR2_REG_EFUSE_DC = 0x01a2dc,
	APEX_BAR2_REG_EFUSE_E0 = 0x01a2e0,
	APEX_BAR2_REG_EFUSE_E4 = 0x01a2e4,
	APEX_BAR2_REG_EFUSE_E8 = 0x01a2e8,

	/* Error registers - Used mostly for debug */
	APEX_BAR2_REG_USER_HIB_ERROR_STATUS = 0x86f0,
	APEX_BAR2_REG_SCALAR_CORE_ERROR_STATUS = 0x41a0,
};

/* Addresses for packed registers. */
#define APEX_BAR2_REG_AXI_QUIESCE (APEX_BAR2_REG_SCU_BASE + 0x2C)
#define APEX_BAR2_REG_GCB_CLOCK_GATE (APEX_BAR2_REG_SCU_BASE + 0x14)
#define APEX_BAR2_REG_SCU_0 (APEX_BAR2_REG_SCU_BASE + 0xc)
#define APEX_BAR2_REG_SCU_1 (APEX_BAR2_REG_SCU_BASE + 0x10)
#define APEX_BAR2_REG_SCU_2 (APEX_BAR2_REG_SCU_BASE + 0x14)
#define APEX_BAR2_REG_SCU_3 (APEX_BAR2_REG_SCU_BASE + 0x18)
#define APEX_BAR2_REG_SCU_4 (APEX_BAR2_REG_SCU_BASE + 0x1c)
#define APEX_BAR2_REG_SCU_5 (APEX_BAR2_REG_SCU_BASE + 0x20)

#define SCU3_RG_PWR_STATE_OVR_BIT_OFFSET 26
#define SCU3_RG_PWR_STATE_OVR_MASK_WIDTH 2
#define SCU3_CUR_RST_GCB_BIT_MASK 0x10
#define SCU2_RG_RST_GCB_BIT_MASK 0xc

/* Configuration for page table. */
static struct gasket_page_table_config apex_page_table_configs[NUM_NODES] = {
	{
		.id = 0,
		.mode = GASKET_PAGE_TABLE_MODE_NORMAL,
		.total_entries = APEX_PAGE_TABLE_TOTAL_ENTRIES,
		.base_reg = APEX_BAR2_REG_KERNEL_HIB_PAGE_TABLE,
		.extended_reg = APEX_BAR2_REG_KERNEL_HIB_EXTENDED_TABLE,
		.extended_bit = APEX_EXTENDED_SHIFT,
	},
};

/* The regions in the BAR2 space that can be mapped into user space. */
static const struct gasket_mappable_region mappable_regions[NUM_REGIONS] = {
	{ 0x40000, 0x1000 },
	{ 0x44000, 0x1000 },
	{ 0x48000, 0x1000 },
};

/* Gasket device interrupts enums must be dense (i.e., no empty slots). */
enum apex_interrupt {
	APEX_INTERRUPT_INSTR_QUEUE = 0,
	APEX_INTERRUPT_INPUT_ACTV_QUEUE = 1,
	APEX_INTERRUPT_PARAM_QUEUE = 2,
	APEX_INTERRUPT_OUTPUT_ACTV_QUEUE = 3,
	APEX_INTERRUPT_SC_HOST_0 = 4,
	APEX_INTERRUPT_SC_HOST_1 = 5,
	APEX_INTERRUPT_SC_HOST_2 = 6,
	APEX_INTERRUPT_SC_HOST_3 = 7,
	APEX_INTERRUPT_TOP_LEVEL_0 = 8,
	APEX_INTERRUPT_TOP_LEVEL_1 = 9,
	APEX_INTERRUPT_TOP_LEVEL_2 = 10,
	APEX_INTERRUPT_TOP_LEVEL_3 = 11,
	APEX_INTERRUPT_FATAL_ERR = 12,
	APEX_INTERRUPT_COUNT = 13,
};

/* Interrupt descriptors for Apex */
static struct gasket_interrupt_desc apex_interrupts[] = {
	{
		APEX_INTERRUPT_INSTR_QUEUE,
		APEX_BAR2_REG_KERNEL_HIB_INSTR_QUEUE_INTVECCTL,
		UNPACKED,
	},
	{
		APEX_INTERRUPT_INPUT_ACTV_QUEUE,
		APEX_BAR2_REG_KERNEL_HIB_INPUT_ACTV_QUEUE_INTVECCTL,
		UNPACKED
	},
	{
		APEX_INTERRUPT_PARAM_QUEUE,
		APEX_BAR2_REG_KERNEL_HIB_PARAM_QUEUE_INTVECCTL,
		UNPACKED
	},
	{
		APEX_INTERRUPT_OUTPUT_ACTV_QUEUE,
		APEX_BAR2_REG_KERNEL_HIB_OUTPUT_ACTV_QUEUE_INTVECCTL,
		UNPACKED
	},
	{
		APEX_INTERRUPT_SC_HOST_0,
		APEX_BAR2_REG_KERNEL_HIB_SC_HOST_INTVECCTL,
		PACK_0
	},
	{
		APEX_INTERRUPT_SC_HOST_1,
		APEX_BAR2_REG_KERNEL_HIB_SC_HOST_INTVECCTL,
		PACK_1
	},
	{
		APEX_INTERRUPT_SC_HOST_2,
		APEX_BAR2_REG_KERNEL_HIB_SC_HOST_INTVECCTL,
		PACK_2
	},
	{
		APEX_INTERRUPT_SC_HOST_3,
		APEX_BAR2_REG_KERNEL_HIB_SC_HOST_INTVECCTL,
		PACK_3
	},
	{
		APEX_INTERRUPT_TOP_LEVEL_0,
		APEX_BAR2_REG_KERNEL_HIB_TOP_LEVEL_INTVECCTL,
		PACK_0
	},
	{
		APEX_INTERRUPT_TOP_LEVEL_1,
		APEX_BAR2_REG_KERNEL_HIB_TOP_LEVEL_INTVECCTL,
		PACK_1
	},
	{
		APEX_INTERRUPT_TOP_LEVEL_2,
		APEX_BAR2_REG_KERNEL_HIB_TOP_LEVEL_INTVECCTL,
		PACK_2
	},
	{
		APEX_INTERRUPT_TOP_LEVEL_3,
		APEX_BAR2_REG_KERNEL_HIB_TOP_LEVEL_INTVECCTL,
		PACK_3
	},
	{
		APEX_INTERRUPT_FATAL_ERR,
		APEX_BAR2_REG_KERNEL_HIB_FATAL_ERR_INTVECCTL,
		UNPACKED
	},
};

/* Allows device to enter power save upon driver close(). */
static int allow_power_save = 1;

/* Allows SW based clock gating. */
static int allow_sw_clock_gating;

/* Allows HW based clock gating. */
/* Note: this is not mutual exclusive with SW clock gating. */
static int allow_hw_clock_gating = 1;

/* Act as if only GCB is instantiated. */
static int bypass_top_level;

module_param(allow_power_save, int, 0644);
module_param(allow_sw_clock_gating, int, 0644);
module_param(allow_hw_clock_gating, int, 0644);
module_param(bypass_top_level, int, 0644);

/* Temperature points in milli C at which DFS is toggled */
#define DEFAULT_TRIP_POINT0_TEMP 85000
#define DEFAULT_TRIP_POINT1_TEMP 90000
#define DEFAULT_TRIP_POINT2_TEMP 95000

static int trip_point0_temp = DEFAULT_TRIP_POINT0_TEMP;
static int trip_point1_temp = DEFAULT_TRIP_POINT1_TEMP;
static int trip_point2_temp = DEFAULT_TRIP_POINT2_TEMP;

module_param(trip_point0_temp, int, 0644);
module_param(trip_point1_temp, int, 0644);
module_param(trip_point2_temp, int, 0644);

/* Hardware monitored temperature trip points in milli C
   Apex chip drives INTR line when reaching hw_temp_warn1 temperature,
   and SD_ALARM line when reaching hw_temp_warn2 if corresponding
   hw_temp_warn*_en is set to true.
 */
static int hw_temp_warn1 = 100000;
static int hw_temp_warn2 = 100000;
static bool hw_temp_warn1_en = false;
static bool hw_temp_warn2_en = true;

module_param(hw_temp_warn1, int, 0644);
module_param(hw_temp_warn2, int, 0644);
module_param(hw_temp_warn1_en, bool, 0644);
module_param(hw_temp_warn2_en, bool, 0644);

/* Temperature poll interval in ms */
static int temp_poll_interval = DEFAULT_APEX_TEMP_POLL_INTERVAL;
module_param(temp_poll_interval, int, 0644);

/* Check the device status registers and return device status ALIVE or DEAD. */
static int apex_get_status(struct gasket_dev *gasket_dev)
{
	/* TODO: Check device status. */
	return GASKET_STATUS_ALIVE;
}

/* Enter GCB reset state. */
static int apex_enter_reset(struct gasket_dev *gasket_dev)
{
	if (bypass_top_level)
		return 0;

	/*
	 * Software reset:
	 * Enable sleep mode
	 *  - Software force GCB idle
	 *    - Enable GCB idle
	 */
	gasket_read_modify_write_64(gasket_dev, APEX_BAR_INDEX,
				    APEX_BAR2_REG_IDLEGENERATOR_IDLEGEN_IDLEREGISTER,
				    0x0, 1, 32);

	/*    - Initiate DMA pause */
	gasket_dev_write_64(gasket_dev, 1, APEX_BAR_INDEX,
			    APEX_BAR2_REG_USER_HIB_DMA_PAUSE);

	/*    - Wait for DMA pause complete. */
	if (gasket_wait_with_reschedule(gasket_dev, APEX_BAR_INDEX,
					APEX_BAR2_REG_USER_HIB_DMA_PAUSED, 1, 1,
					APEX_RESET_DELAY, APEX_RESET_RETRY)) {
		dev_err(gasket_dev->dev,
			"DMAs did not quiesce within timeout (%d ms)\n",
			APEX_RESET_RETRY * APEX_RESET_DELAY);
		return -ETIMEDOUT;
	}

	/*  - Enable GCB reset (0x1 to rg_rst_gcb) */
	gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
				    APEX_BAR2_REG_SCU_2, 0x1, 2, 2);

	/*  - Enable GCB clock Gate (0x1 to rg_gated_gcb) */
	gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
				    APEX_BAR2_REG_SCU_2, 0x1, 2, 18);

	/*  - Enable GCB memory shut down (0x3 to rg_force_ram_sd) */
	gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
				    APEX_BAR2_REG_SCU_3, 0x3, 2, 14);

	/*    - Wait for RAM shutdown. */
	if (gasket_wait_with_reschedule(gasket_dev, APEX_BAR_INDEX,
					APEX_BAR2_REG_SCU_3, 1 << 6, 1 << 6,
					APEX_RESET_DELAY, APEX_RESET_RETRY)) {
		dev_err(gasket_dev->dev,
			"RAM did not shut down within timeout (%d ms)\n",
			APEX_RESET_RETRY * APEX_RESET_DELAY);
		return -ETIMEDOUT;
	}

	return 0;
}

/* Quit GCB reset state. */
static int apex_quit_reset(struct gasket_dev *gasket_dev)
{
	u32 val0, val1;

	if (bypass_top_level)
		return 0;

	/*
	 * Disable sleep mode:
	 *  - Disable GCB memory shut down:
	 *    - b00: Not forced (HW controlled)
	 *    - b1x: Force disable
	 */
	gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
				    APEX_BAR2_REG_SCU_3, 0x0, 2, 14);

	/*
	 *  - Disable software clock gate:
	 *    - b00: Not forced (HW controlled)
	 *    - b1x: Force disable
	 */
	gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
				    APEX_BAR2_REG_SCU_2, 0x0, 2, 18);

	/*
	 *  - Disable GCB reset (rg_rst_gcb):
	 *    - b00: Not forced (HW controlled)
	 *    - b1x: Force disable = Force not Reset
	 */
	gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
				    APEX_BAR2_REG_SCU_2, 0x2, 2, 2);

	/*    - Wait for RAM enable. */
	if (gasket_wait_with_reschedule(gasket_dev, APEX_BAR_INDEX,
					APEX_BAR2_REG_SCU_3, 1 << 6, 0,
					APEX_RESET_DELAY, APEX_RESET_RETRY)) {
		dev_err(gasket_dev->dev,
			"RAM did not enable within timeout (%d ms)\n",
			APEX_RESET_RETRY * APEX_RESET_DELAY);
		return -ETIMEDOUT;
	}

	/*    - Wait for Reset complete. */
	if (gasket_wait_with_reschedule(gasket_dev, APEX_BAR_INDEX,
					APEX_BAR2_REG_SCU_3,
					SCU3_CUR_RST_GCB_BIT_MASK, 0,
					APEX_RESET_DELAY, APEX_RESET_RETRY)) {
		dev_err(gasket_dev->dev,
			"GCB did not leave reset within timeout (%d ms)\n",
			APEX_RESET_RETRY * APEX_RESET_DELAY);
		return -ETIMEDOUT;
	}

	if (!allow_hw_clock_gating) {
		val0 = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					  APEX_BAR2_REG_SCU_3);
		/* Inactive and Sleep mode are disabled. */
		gasket_read_modify_write_32(gasket_dev,
					    APEX_BAR_INDEX,
					    APEX_BAR2_REG_SCU_3, 0x3,
					    SCU3_RG_PWR_STATE_OVR_MASK_WIDTH,
					    SCU3_RG_PWR_STATE_OVR_BIT_OFFSET);
		val1 = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					  APEX_BAR2_REG_SCU_3);
		dev_dbg(gasket_dev->dev,
			"Disallow HW clock gating 0x%x -> 0x%x\n", val0, val1);
	} else {
		val0 = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					  APEX_BAR2_REG_SCU_3);
		/* Inactive mode enabled - Sleep mode disabled. */
		gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
					    APEX_BAR2_REG_SCU_3, 2,
					    SCU3_RG_PWR_STATE_OVR_MASK_WIDTH,
					    SCU3_RG_PWR_STATE_OVR_BIT_OFFSET);
		val1 = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					  APEX_BAR2_REG_SCU_3);
		dev_dbg(gasket_dev->dev, "Allow HW clock gating 0x%x -> 0x%x\n",
			val0, val1);
	}

	return 0;
}

/* Reset the Apex hardware. Called on final close via device_close_cb. */
static int apex_device_cleanup(struct gasket_dev *gasket_dev)
{
	u64 scalar_error;
	u64 hib_error;
	int ret = 0;

	hib_error = gasket_dev_read_64(gasket_dev, APEX_BAR_INDEX,
				       APEX_BAR2_REG_USER_HIB_ERROR_STATUS);
	scalar_error = gasket_dev_read_64(gasket_dev, APEX_BAR_INDEX,
					  APEX_BAR2_REG_SCALAR_CORE_ERROR_STATUS);

	dev_dbg(gasket_dev->dev,
		"%s 0x%p hib_error 0x%llx scalar_error 0x%llx\n",
		__func__, gasket_dev, hib_error, scalar_error);

	if (allow_power_save)
		ret = apex_enter_reset(gasket_dev);

	return ret;
}

/* Determine if GCB is in reset state. */
static bool is_gcb_in_reset(struct gasket_dev *gasket_dev)
{
	u32 val = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
				     APEX_BAR2_REG_SCU_3);

	/* Masks rg_rst_gcb bit of SCU_CTRL_2 */
	return (val & SCU3_CUR_RST_GCB_BIT_MASK);
}

/* Reset the hardware, then quit reset.  Called on device open. */
static int apex_reset(struct gasket_dev *gasket_dev)
{
	int ret;

	if (bypass_top_level)
		return 0;

	if (!is_gcb_in_reset(gasket_dev)) {
		/* We are not in reset - toggle the reset bit so as to force
		 * re-init of custom block
		 */
		dev_dbg(gasket_dev->dev, "%s: toggle reset\n", __func__);

		ret = apex_enter_reset(gasket_dev);
		if (ret)
			return ret;
	}
	ret = apex_quit_reset(gasket_dev);

	return ret;
}

/*
 * Check permissions for Apex ioctls.
 * Returns true if the current user may execute this ioctl, and false otherwise.
 */
static bool apex_ioctl_check_permissions(struct file *filp, uint cmd)
{
	return !!(filp->f_mode & FMODE_WRITE);
}

/* Gates or un-gates Apex clock. */
static long apex_clock_gating(struct gasket_dev *gasket_dev,
			      struct apex_gate_clock_ioctl __user *argp)
{
	struct apex_gate_clock_ioctl ibuf;

	if (bypass_top_level || !allow_sw_clock_gating)
		return 0;

	if (copy_from_user(&ibuf, argp, sizeof(ibuf)))
		return -EFAULT;

	dev_dbg(gasket_dev->dev, "%s %llu\n", __func__, ibuf.enable);

	if (ibuf.enable) {
		/* Quiesce AXI, gate GCB clock. */
		gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
					    APEX_BAR2_REG_AXI_QUIESCE, 0x1, 1,
					    16);
		gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
					    APEX_BAR2_REG_GCB_CLOCK_GATE, 0x1,
					    2, 18);
	} else {
		/* Un-gate GCB clock, un-quiesce AXI. */
		gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
					    APEX_BAR2_REG_GCB_CLOCK_GATE, 0x0,
					    2, 18);
		gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
					    APEX_BAR2_REG_AXI_QUIESCE, 0x0, 1,
					    16);
	}
	return 0;
}

/* apex_set_performance_expectation: Adjust clock rates for Apex. */
static long apex_set_performance_expectation(
	struct gasket_dev *gasket_dev,
	struct apex_performance_expectation_ioctl __user *argp)
{
	struct apex_performance_expectation_ioctl ibuf;
	uint32_t rg_gcb_clk_div = 0;
	uint32_t rg_axi_clk_fixed = 0;
	const int AXI_CLK_FIXED_SHIFT = 2;
	const int MCU_CLK_FIXED_SHIFT = 3;

	// 8051 clock is fixed for PCIe, as it's not used at all.
	const uint32_t rg_8051_clk_fixed = 1;

	if (bypass_top_level)
		return 0;

	if (copy_from_user(&ibuf, argp, sizeof(ibuf)))
		return -EFAULT;

	switch (ibuf.performance) {
		case APEX_PERFORMANCE_LOW:
			rg_gcb_clk_div = 3;
			rg_axi_clk_fixed = 0;
			break;

		case APEX_PERFORMANCE_MED:
			rg_gcb_clk_div = 2;
			rg_axi_clk_fixed = 0;
			break;

		case APEX_PERFORMANCE_HIGH:
			rg_gcb_clk_div = 1;
			rg_axi_clk_fixed = 0;
			break;

		case APEX_PERFORMANCE_MAX:
			rg_gcb_clk_div = 0;
			rg_axi_clk_fixed = 0;
			break;

		default:
			return -EINVAL;
	}

	/*
	 * Set clock rates for GCB, AXI, and 8051:
	 */
	gasket_read_modify_write_32(
		gasket_dev, APEX_BAR_INDEX, APEX_BAR2_REG_SCU_3,
                (rg_gcb_clk_div | (rg_axi_clk_fixed << AXI_CLK_FIXED_SHIFT) | (rg_8051_clk_fixed << MCU_CLK_FIXED_SHIFT)),
                /*mask_width=*/4, /*mask_shift=*/28);

	return 0;
}

/* Apex-specific ioctl handler. */
static long apex_ioctl(struct file *filp, uint cmd, void __user *argp)
{
	struct gasket_dev *gasket_dev = filp->private_data;

	if (!apex_ioctl_check_permissions(filp, cmd))
		return -EPERM;

	switch (cmd) {
	case APEX_IOCTL_GATE_CLOCK:
		return apex_clock_gating(gasket_dev, argp);
	case APEX_IOCTL_PERFORMANCE_EXPECTATION:
		return apex_set_performance_expectation(gasket_dev, argp);
	default:
		return -ENOTTY; /* unknown command */
	}
}

/* Linear fit optimized for 25C-100C */
static int adc_to_millic(int adc)
{
	return (662 - adc) * 250 + 550;
}

static int millic_to_adc(int millic)
{
	return (550 - millic) / 250 + 662;
}

/* Display driver sysfs entries. */
static ssize_t sysfs_show(struct device *device, struct device_attribute *attr,
			  char *buf)
{
	int ret;
	unsigned value, value2, value3, value4;
	struct gasket_dev *gasket_dev;
	struct apex_dev *apex_dev;
	struct gasket_sysfs_attribute *gasket_attr;
	enum sysfs_attribute_type type;

	gasket_dev = gasket_sysfs_get_device_data(device);
	if (!gasket_dev) {
		dev_err(device, "No Apex device sysfs mapping found\n");
		return -ENODEV;
	}

	if (!gasket_dev->pci_dev ||
	    !(apex_dev = pci_get_drvdata(gasket_dev->pci_dev))) {
		dev_err(device, "Can't find apex_dev data\n");
		gasket_sysfs_put_device_data(device, gasket_dev);
		return -ENODEV;
	}

	gasket_attr = gasket_sysfs_get_attr(device, attr);
	if (!gasket_attr) {
		dev_err(device, "No Apex device sysfs attr data found\n");
		gasket_sysfs_put_device_data(device, gasket_dev);
		return -ENODEV;
	}

	type = (enum sysfs_attribute_type)gasket_attr->data.attr_type;
	switch (type) {
	case ATTR_KERNEL_HIB_PAGE_TABLE_SIZE:
		ret = scnprintf(buf, PAGE_SIZE, "%u\n",
				gasket_page_table_num_entries(
					gasket_dev->page_table[0]));
		break;
	case ATTR_KERNEL_HIB_SIMPLE_PAGE_TABLE_SIZE:
		ret = scnprintf(buf, PAGE_SIZE, "%u\n",
				gasket_page_table_num_simple_entries(
					gasket_dev->page_table[0]));
		break;
	case ATTR_KERNEL_HIB_NUM_ACTIVE_PAGES:
		ret = scnprintf(buf, PAGE_SIZE, "%u\n",
				gasket_page_table_num_active_pages(
					gasket_dev->page_table[0]));
		break;
	case ATTR_TEMP:
		value = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					   APEX_BAR2_REG_OMC0_DC);
		value = (value >> 16) & ((1 << 10) - 1);
		ret = scnprintf(buf, PAGE_SIZE, "%i\n", adc_to_millic(value));
		break;
	case ATTR_TEMP_WARN1:
		value = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					   APEX_BAR2_REG_OMC0_D4);
		value = (value >> 16) & ((1 << 10) - 1);
		ret = scnprintf(buf, PAGE_SIZE, "%i\n", adc_to_millic(value));
		break;
	case ATTR_TEMP_WARN2:
		value = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					   APEX_BAR2_REG_OMC0_D8);
		value = (value >> 16) & ((1 << 10) - 1);
		ret = scnprintf(buf, PAGE_SIZE, "%i\n", adc_to_millic(value));
		break;
	case ATTR_TEMP_WARN1_EN:
		value = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					   APEX_BAR2_REG_OMC0_D4);
		ret = scnprintf(buf, PAGE_SIZE, "%i\n", value >> 31);
		break;
	case ATTR_TEMP_WARN2_EN:
		value = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					   APEX_BAR2_REG_OMC0_D8);
		ret = scnprintf(buf, PAGE_SIZE, "%i\n", value >> 31);
		break;
	case ATTR_TEMP_TRIP0:
		ret = scnprintf(buf, PAGE_SIZE, "%i\n",
				adc_to_millic(apex_dev->adc_trip_points[0]));
		break;
	case ATTR_TEMP_TRIP1:
		ret = scnprintf(buf, PAGE_SIZE, "%i\n",
				adc_to_millic(apex_dev->adc_trip_points[1]));
		break;
	case ATTR_TEMP_TRIP2:
		ret = scnprintf(buf, PAGE_SIZE, "%i\n",
				adc_to_millic(apex_dev->adc_trip_points[2]));
		break;
	case ATTR_TEMP_POLL_INTERVAL:
		ret = scnprintf(buf, PAGE_SIZE, "%i\n",
				atomic_read(&apex_dev->temp_poll_interval));
		break;
	case ATTR_UNIQUE_ID:
		value = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					   APEX_BAR2_REG_EFUSE_DC);
		value2 = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					    APEX_BAR2_REG_EFUSE_E0);
		value3 = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					    APEX_BAR2_REG_EFUSE_E4);
		value4 = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
					    APEX_BAR2_REG_EFUSE_E8);
		ret = snprintf(buf, PAGE_SIZE, "%.8x%.8x%.8x%.8x\n", value4,
			       value3, value2, value);
		break;

	default:
		dev_dbg(gasket_dev->dev, "Unknown attribute: %s\n",
			attr->attr.name);
		ret = 0;
		break;
	}

	gasket_sysfs_put_attr(device, gasket_attr);
	gasket_sysfs_put_device_data(device, gasket_dev);
	return ret;
}

/* Set driver sysfs entries. */
static ssize_t sysfs_store(struct device *device, struct device_attribute *attr,
			   const char *buf, size_t count)
{
	int ret = count, value;
	struct gasket_dev *gasket_dev;
	struct apex_dev *apex_dev;
	struct gasket_sysfs_attribute *gasket_attr;
	enum sysfs_attribute_type type;

	if (kstrtoint(buf, 10, &value))
		return -EINVAL;

	gasket_dev = gasket_sysfs_get_device_data(device);
	if (!gasket_dev) {
		dev_err(device, "No Apex device sysfs mapping found\n");
		return -ENODEV;
	}

	if (!gasket_dev->pci_dev ||
	    !(apex_dev = pci_get_drvdata(gasket_dev->pci_dev))) {
		dev_err(device, "Can't find apex_dev data\n");
		gasket_sysfs_put_device_data(device, gasket_dev);
		return -ENODEV;
	}

	gasket_attr = gasket_sysfs_get_attr(device, attr);
	if (!gasket_attr) {
		dev_err(device, "No Apex device sysfs attr data found\n");
		gasket_sysfs_put_device_data(device, gasket_dev);
		return -ENODEV;
	}

	type = (enum sysfs_attribute_type)gasket_attr->data.attr_type;
	switch (type) {
	case ATTR_TEMP_WARN1:
		value = millic_to_adc(value);
		gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
					    APEX_BAR2_REG_OMC0_D4, value, 10,
					    16);
		break;
	case ATTR_TEMP_WARN2:
		value = millic_to_adc(value);
		gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
					    APEX_BAR2_REG_OMC0_D8, value, 10,
					    16);
		break;
	case ATTR_TEMP_WARN1_EN:
		value = value > 0 ? 1 : 0;
		gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
					    APEX_BAR2_REG_OMC0_D4, value, 1,
					    31);
		break;
	case ATTR_TEMP_WARN2_EN:
		value = value > 0 ? 1 : 0;
		gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
					    APEX_BAR2_REG_OMC0_D8, value, 1,
					    31);
		break;
	case ATTR_TEMP_TRIP0:
		value = millic_to_adc(value);
		/* Note: that adc values should be in descending order */
		if (value >= apex_dev->adc_trip_points[1]) {
			apex_dev->adc_trip_points[0] = value;
		} else ret = -EINVAL;
		break;
	case ATTR_TEMP_TRIP1:
		value = millic_to_adc(value);
		if (value <= apex_dev->adc_trip_points[0] &&
		    value >= apex_dev->adc_trip_points[2]) {
			apex_dev->adc_trip_points[1] = value;
		} else ret = -EINVAL;
		break;
	case ATTR_TEMP_TRIP2:
		value = millic_to_adc(value);
		if (value <= apex_dev->adc_trip_points[1]) {
			apex_dev->adc_trip_points[2] = value;
		} else ret = -EINVAL;
		break;
	case ATTR_TEMP_POLL_INTERVAL:
		cancel_delayed_work_sync(&apex_dev->check_temperature_work);
		atomic_set(&apex_dev->temp_poll_interval, value);
		if (value > 0)
			schedule_delayed_work(&apex_dev->check_temperature_work,
					      msecs_to_jiffies(value));

		break;
	default:
		dev_dbg(gasket_dev->dev, "Unknown attribute: %s\n",
			attr->attr.name);
		ret = 0;
		break;
	}

	gasket_sysfs_put_attr(device, gasket_attr);
	gasket_sysfs_put_device_data(device, gasket_dev);
	return ret;
}

static struct gasket_sysfs_attribute apex_sysfs_attrs[] = {
	GASKET_SYSFS_RO(node_0_page_table_entries, sysfs_show,
			ATTR_KERNEL_HIB_PAGE_TABLE_SIZE),
	GASKET_SYSFS_RO(node_0_simple_page_table_entries, sysfs_show,
			ATTR_KERNEL_HIB_SIMPLE_PAGE_TABLE_SIZE),
	GASKET_SYSFS_RO(node_0_num_mapped_pages, sysfs_show,
			ATTR_KERNEL_HIB_NUM_ACTIVE_PAGES),
	GASKET_SYSFS_RO(temp, sysfs_show, ATTR_TEMP),
	GASKET_SYSFS_RW(hw_temp_warn1, sysfs_show, sysfs_store,
			ATTR_TEMP_WARN1),
	GASKET_SYSFS_RW(hw_temp_warn1_en, sysfs_show, sysfs_store,
			ATTR_TEMP_WARN1_EN),
	GASKET_SYSFS_RW(hw_temp_warn2, sysfs_show, sysfs_store,
			ATTR_TEMP_WARN2),
	GASKET_SYSFS_RW(hw_temp_warn2_en, sysfs_show, sysfs_store,
			ATTR_TEMP_WARN2_EN),
	GASKET_SYSFS_RW(trip_point0_temp, sysfs_show, sysfs_store,
			ATTR_TEMP_TRIP0),
	GASKET_SYSFS_RW(trip_point1_temp, sysfs_show, sysfs_store,
			ATTR_TEMP_TRIP1),
	GASKET_SYSFS_RW(trip_point2_temp, sysfs_show, sysfs_store,
			ATTR_TEMP_TRIP2),
	GASKET_SYSFS_RW(temp_poll_interval, sysfs_show, sysfs_store,
			ATTR_TEMP_POLL_INTERVAL),
	GASKET_SYSFS_RO(unique_id, sysfs_show, ATTR_UNIQUE_ID),
	GASKET_END_OF_ATTR_ARRAY
};

static void apply_module_params(struct apex_dev *apex_dev) {
	kernel_param_lock(THIS_MODULE);

	/* use defaults if trip point temperatures are not in ascending order */
	if (trip_point0_temp > trip_point1_temp ||
	    trip_point1_temp > trip_point2_temp) {
		dev_warn(apex_dev->gasket_dev_ptr->dev,
			 "Invalid module parameters for temperature trip points"
			 ", using defaults\n");
		trip_point0_temp = DEFAULT_TRIP_POINT0_TEMP;
		trip_point1_temp = DEFAULT_TRIP_POINT1_TEMP;
		trip_point2_temp = DEFAULT_TRIP_POINT2_TEMP;
	}

	apex_dev->adc_trip_points[0] = millic_to_adc(trip_point0_temp);
	apex_dev->adc_trip_points[1] = millic_to_adc(trip_point1_temp);
	apex_dev->adc_trip_points[2] = millic_to_adc(trip_point2_temp);
	atomic_set(&apex_dev->temp_poll_interval, temp_poll_interval);

	gasket_read_modify_write_32(apex_dev->gasket_dev_ptr, APEX_BAR_INDEX,
				    APEX_BAR2_REG_OMC0_D4,
				    millic_to_adc(hw_temp_warn1), 10, 16);
	gasket_read_modify_write_32(apex_dev->gasket_dev_ptr, APEX_BAR_INDEX,
				    APEX_BAR2_REG_OMC0_D8,
				    millic_to_adc(hw_temp_warn2), 10, 16);
	if (hw_temp_warn1_en)
		gasket_read_modify_write_32(apex_dev->gasket_dev_ptr,
					    APEX_BAR_INDEX,
					    APEX_BAR2_REG_OMC0_D4, 1, 1, 31);

	if (hw_temp_warn2_en)
		gasket_read_modify_write_32(apex_dev->gasket_dev_ptr,
					    APEX_BAR_INDEX,
					    APEX_BAR2_REG_OMC0_D8, 1, 1, 31);

	kernel_param_unlock(THIS_MODULE);
}

static void check_temperature_work_handler(struct work_struct *work) {
	int i, temp_poll_interval;
	u32 adc_temp, clk_div, tmp;
	const u32 mask = ((1 << 2) - 1) << 28;
	struct apex_dev *apex_dev =
		container_of(work, struct apex_dev,
			     check_temperature_work.work);
	struct gasket_dev *gasket_dev = apex_dev->gasket_dev_ptr;

	mutex_lock(&gasket_dev->mutex);

	/* Read current temperature */
	adc_temp = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
				      APEX_BAR2_REG_OMC0_DC);
	adc_temp = (adc_temp >> 16) & ((1 << 10) - 1);

	/* Find closest trip point
	   Note: that adc values are in descending order */
	for (i = ARRAY_SIZE(apex_dev->adc_trip_points) - 1; i >= 0; --i) {
		if (adc_temp <= apex_dev->adc_trip_points[i])
			break;
	}
	/* Compute divider value and shift into appropriate bit location */
	clk_div = (i + 1) << 28;

	/* Modify gcb clk divider if it's different from current one */
	tmp = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
				 APEX_BAR2_REG_SCU_3);
	if (clk_div != (tmp & mask)) {
		tmp = (tmp & ~mask) | clk_div;
		gasket_dev_write_32(gasket_dev, tmp, APEX_BAR_INDEX,
				    APEX_BAR2_REG_SCU_3);
		dev_warn(gasket_dev->dev,
			 "Apex performance %sthrottled due to temperature\n",
			 i == -1 ? "not " : "");
	}

	mutex_unlock(&gasket_dev->mutex);

	temp_poll_interval = atomic_read(&apex_dev->temp_poll_interval);
	if (temp_poll_interval > 0)
		schedule_delayed_work(&apex_dev->check_temperature_work,
				      msecs_to_jiffies(temp_poll_interval));
}

/* On device open, perform a core reinit reset. */
static int apex_device_open_cb(struct gasket_dev *gasket_dev)
{
	return gasket_reset_nolock(gasket_dev);
}

static const struct pci_device_id apex_pci_ids[] = {
	{ PCI_DEVICE(APEX_PCI_VENDOR_ID, APEX_PCI_DEVICE_ID) }, { 0 }
};

static void apex_pci_fixup_class(struct pci_dev *pdev)
{
	pdev->class = (PCI_CLASS_SYSTEM_OTHER << 8) | pdev->class;
}
DECLARE_PCI_FIXUP_CLASS_HEADER(APEX_PCI_VENDOR_ID, APEX_PCI_DEVICE_ID,
			       PCI_ANY_ID, 8, apex_pci_fixup_class);

static int apex_pci_probe(struct pci_dev *pci_dev,
			  const struct pci_device_id *id)
{
	int ret, temp_poll_interval;
	ulong page_table_ready, msix_table_ready;
	int retries = 0;
	struct gasket_dev *gasket_dev;
	struct apex_dev *apex_dev;

	ret = pci_enable_device(pci_dev);
#ifdef MODULE
	if (ret) {
		apex_pci_fixup_class(pci_dev);
		pci_bus_assign_resources(pci_dev->bus);
		ret = pci_enable_device(pci_dev);
	}
#endif
	if (ret) {
		dev_err(&pci_dev->dev, "error enabling PCI device\n");
		return ret;
	}

	pci_set_master(pci_dev);

	ret = gasket_pci_add_device(pci_dev, &gasket_dev);
	if (ret) {
		dev_err(&pci_dev->dev, "error adding gasket device\n");
		pci_disable_device(pci_dev);
		return ret;
	}

	apex_dev = kzalloc(sizeof(*apex_dev), GFP_KERNEL);
	if (!apex_dev) {
		dev_err(&pci_dev->dev, "no memory for device\n");
		ret = -ENOMEM;
		goto remove_device;
	}

	INIT_DELAYED_WORK(&apex_dev->check_temperature_work,
			  check_temperature_work_handler);
	apex_dev->gasket_dev_ptr = gasket_dev;
	apply_module_params(apex_dev);
	pci_set_drvdata(pci_dev, apex_dev);
	apex_reset(gasket_dev);

	while (retries < APEX_RESET_RETRY) {
		page_table_ready =
			gasket_dev_read_64(gasket_dev, APEX_BAR_INDEX,
					   APEX_BAR2_REG_KERNEL_HIB_PAGE_TABLE_INIT);
		msix_table_ready =
			gasket_dev_read_64(gasket_dev, APEX_BAR_INDEX,
					   APEX_BAR2_REG_KERNEL_HIB_MSIX_TABLE_INIT);
		if (page_table_ready && msix_table_ready)
			break;
		schedule_timeout(msecs_to_jiffies(APEX_RESET_DELAY));
		retries++;
	}

	if (retries == APEX_RESET_RETRY) {
		if (!page_table_ready)
			dev_err(gasket_dev->dev, "Page table init timed out\n");
		if (!msix_table_ready)
			dev_err(gasket_dev->dev, "MSI-X table init timed out\n");
		ret = -ETIMEDOUT;
		goto remove_device;
	}

	// Enable thermal sensor clocks
	gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
				    APEX_BAR2_REG_OMC0_D0, 0x1, 1, 7);

	// Enable thermal sensor (ENAD ENVR ENBG)
	gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
				    APEX_BAR2_REG_OMC0_D8, 0x7, 3, 0);

	// Enable OMC thermal sensor controller
	// This bit should be asserted 100 us after ENAD ENVR ENBG
	schedule_timeout(usecs_to_jiffies(100));
	gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
				    APEX_BAR2_REG_OMC0_DC, 0x1, 1, 0);

	ret = gasket_sysfs_create_entries(gasket_dev->dev_info.device,
					  apex_sysfs_attrs);
	if (ret)
		dev_err(&pci_dev->dev, "error creating device sysfs entries\n");

	ret = gasket_enable_device(gasket_dev);
	if (ret) {
		dev_err(&pci_dev->dev, "error enabling gasket device\n");
		goto remove_device;
	}

	/* Place device in low power mode until opened */
	if (allow_power_save)
		apex_enter_reset(gasket_dev);

	/* Enable thermal polling */
	temp_poll_interval = atomic_read(&apex_dev->temp_poll_interval);
	if (temp_poll_interval > 0)
		schedule_delayed_work(&apex_dev->check_temperature_work,
				      msecs_to_jiffies(temp_poll_interval));
	return 0;

remove_device:
	gasket_pci_remove_device(pci_dev);
	pci_disable_device(pci_dev);
	kfree(apex_dev);
	return ret;
}

static void apex_pci_remove(struct pci_dev *pci_dev)
{
	struct apex_dev *apex_dev = pci_get_drvdata(pci_dev);
	struct gasket_dev *gasket_dev;

	if (!apex_dev) {
		dev_err(&pci_dev->dev, "NULL apex_dev\n");
		goto remove_device;
	}
	gasket_dev = apex_dev->gasket_dev_ptr;

	cancel_delayed_work_sync(&apex_dev->check_temperature_work);
	kfree(apex_dev);

	gasket_disable_device(gasket_dev);
remove_device:
	gasket_pci_remove_device(pci_dev);
	pci_disable_device(pci_dev);
}

static struct gasket_driver_desc apex_desc = {
	.name = "apex",
	.driver_version = APEX_DRIVER_VERSION,
	.major = 120,
	.minor = 0,
	.module = THIS_MODULE,
	.pci_id_table = apex_pci_ids,

	.num_page_tables = NUM_NODES,
	.page_table_bar_index = APEX_BAR_INDEX,
	.page_table_configs = apex_page_table_configs,
	.page_table_extended_bit = APEX_EXTENDED_SHIFT,

	.bar_descriptions = {
		GASKET_UNUSED_BAR,
		GASKET_UNUSED_BAR,
		{ APEX_BAR_BYTES, (VM_WRITE | VM_READ), APEX_BAR_OFFSET,
			NUM_REGIONS, mappable_regions, PCI_BAR },
		GASKET_UNUSED_BAR,
		GASKET_UNUSED_BAR,
		GASKET_UNUSED_BAR,
	},
	.coherent_buffer_description = {
		APEX_CH_MEM_BYTES,
		(VM_WRITE | VM_READ),
		APEX_CM_OFFSET,
	},
	.interrupt_type = PCI_MSIX,
	.interrupt_bar_index = APEX_BAR_INDEX,
	.num_interrupts = APEX_INTERRUPT_COUNT,
	.interrupts = apex_interrupts,
	.interrupt_pack_width = 7,

	.device_open_cb = apex_device_open_cb,
	.device_close_cb = apex_device_cleanup,

	.ioctl_handler_cb = apex_ioctl,
	.device_status_cb = apex_get_status,
	.hardware_revision_cb = NULL,
	.device_reset_cb = apex_reset,
};

static struct pci_driver apex_pci_driver = {
	.name = "apex",
	.probe = apex_pci_probe,
	.remove = apex_pci_remove,
	.id_table = apex_pci_ids,
};

static int __init apex_init(void)
{
	int ret;

	ret = gasket_register_device(&apex_desc);
	if (ret)
		return ret;
	ret = pci_register_driver(&apex_pci_driver);
	if (ret)
		gasket_unregister_device(&apex_desc);
	return ret;
}

static void apex_exit(void)
{
	pci_unregister_driver(&apex_pci_driver);
	gasket_unregister_device(&apex_desc);
}
MODULE_DESCRIPTION("Google Apex driver");
MODULE_VERSION(APEX_DRIVER_VERSION);
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("John Joseph <jnjoseph@google.com>");
MODULE_DEVICE_TABLE(pci, apex_pci_ids);
module_init(apex_init);
module_exit(apex_exit);